Guest

Cisco IOS Software Releases 12.4 T

ADSL HWICs

  • Viewing Options

  • PDF (419.6 KB)
  • Feedback
ADSL HWICs

Table Of Contents

ADSL HWICs

Contents

Restrictions for ADSL HWICs

Information about ADSL HWICs

ADSL Features

Interface Numbering on Cisco Integrated Services Routers

How to Configure ADSL HWICs

Configuring an ADSL HWIC

Configuration Example for ADSL HWICs

VoIP over ATM (AAL5) on the ADSL Interface: Example

Additional References

Related Documents

Standards

MIBs

RFCs

Technical Assistance

Command Reference

dsl operating-mode

show diag


ADSL HWICs


The ADSL high speed WAN interface cards (HWICs) feature for Cisco modular integrated services routers provide high-speed ADSL digital data transfer between a single customer premises equipment (CPE) subscriber and a central office (CO). ADSL HWICs are available in the following variations:

HWIC-1ADSL, a 1-port ADSL over POTS (ADSLoPOTS) card

HWIC-1ADSLI, a 1-port ADSL over ISDN (ADSLoISDN) card

Feature History for ADSL HWICs

Release
Modification

12.4(4)T

This feature was introduced.


Finding Support Information for Platforms and Cisco IOS Software Images

Use Cisco Feature Navigator to find information about platform support and Cisco IOS software image support. Access Cisco Feature Navigator at http://www.cisco.com/go/fn. You must have an account on Cisco.com. If you do not have an account or have forgotten your username or password, click Cancel at the login dialog box and follow the instructions that appear.

Contents

Restrictions for ADSL HWICs

Information about ADSL HWICs

How to Configure ADSL HWICs

Configuration Example for ADSL HWICs

Additional References

Command Reference

Restrictions for ADSL HWICs

ADSL HWICs can be inserted only into onboard HWIC-enabled slots on Cisco routers. Initially, these routers are the Cisco 1800 series (modular), the Cisco 2800 series, and the Cisco 3800 series integrated services routers.

ATM adaption layer 2 (AAL2) is not supported.

ADSL HWICs do not support dual latency. When the ADSL link is intended to support both voice and data traffic simultaneously, the link should be configured for either all fast-path data or all interleave data with an interleave depth of zero to insure that latency is minimized. In addition, the total supported data rate must be reduced to adjust for the reduced coding gain, which is usually present with high-latency traffic.

The following command is not supported by ADSL HWICs:

clock rate

Loop back functionality is not supported.

Information about ADSL HWICs

This section provides information about the ADSL HWICs feature.

ADSL Features

Interface Numbering on Cisco Integrated Services Routers

ADSL Features

Supported ADSL features are as follows:

HWIC-1ADSL and HWIC-1ADSLI provide ADSL high-speed digital data transmissions between the customer premises equipment (CPE) and the central office (CO).

HWIC-1ADSL supports ADSL-over-POTS (ADSL, ADSL2, and ADSL2+), complying with Annex A of ITU G.992.1, G.992.3, and G.992.5.

HWIC-1ADSLI supports ADSL-over-ISDN (ADSL, ADSL2, and ADSL2+), complying with Annex B of ITU G.992.1, G.992.3, and G.992.5. It also supports and complies with ETSI 101-388 and the Deutsche Telekom U-R2 specification.

HWIC-1ADSL and HWIC-1ADSLI support reach-extended ADSL2, complying with Annex L of ITU G.992.3.

HWIC-1ADSL and HWIC-1ADSLI comply with ANSI T1.413 issue 2.

HWIC-1ADSL and HWIC-1ADSLI support ATM AAL5 services and applications, ATM class of service (constant bit rate [CBR], variable bit rate-nonreal time [VBR-nrt], variable bit rate-real time [VBR-rt], and unspecified bit rate [UBR]), and up to 23 virtual circuits on an HWIC in Cisco routers.

HWIC-1ADSL and HWIC-1ADSLI provide ATM traffic management and Quality of Service (QoS) features to enable service providers to manage their core ATM network infrastructures.

HWIC-1ADSL and HWIC-1ADSLI support Dying Gasp functionality.

Interface Numbering on Cisco Integrated Services Routers

This section describes the interface numbering scheme for Cisco integrated services routers If an interface card is installed in a Cisco 1800 series (modular), Cisco 2800 series, or Cisco 3800 series router, the interfaces must use a triple-number scheme to identify them. This triple-number assignment is different from the standard interface numbering scheme on other Cisco routers.

Table 1 shows the interface numbering for the onboard Fast Ethernet ports and the interface slots on Cisco 1800 series (modular), Cisco 2800 series, and Cisco 3800 series integrated services routers.

Table 1 Interface Numbering on Cisco Integrated Services Routers

Port/Slot
Interface Numbering
Example

Fast Ethernet ports (onboard)

0/0, 0/1

FE 0/0, 0/1

Slot 0

Slot 0/0/0

FE 0/0/0, 0/0/1, 0/0/2, 0/0/3

Slot 1

Slot 0/1/0

(Serial 2T) Serial 0/1/0, 0/1/1

Slot 2

Slot 0/2/0

FE 0/2/0

Slot 3

Slot 0/3/0

(ADSL) ATM 0/3/0


How to Configure ADSL HWICs

This section describes the ADSL configuration task for this feature.


Note Features configured on the ADSL HWIC must also be configured on the Digital Subscriber Loop Access Multiplexer (DSLAM) located in the CO. See the documentation for the specific DSLAM for information about configuring features.


Configuring an ADSL HWIC

To configure an ADSL HWIC, complete the following steps:

SUMMARY STEPS

1. enable

2. configure terminal

3. interface atm interface-id

4. ip address IP-address

5. pvc [name] vpi/vci

6. protocol ip IP-address

7. vbr-rt peak-rate average-rate burst

8. encapsulation {aal5autoppp | aal5ciscoppp | aal5mux | aal5nlpid | aal5snap}

9. exit

10. dsl operating-mode {ansi-dmt | auto | itu-dmt | adsl2 | adsl2+}
or
dsl operating-mode {etsi | auto | itu-dmt | adsl2 | adsl2+}

11. no shutdown

12. exit

13. exit

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

Router(config)# interface atm interface-id

Example:

Router(config)# interface atm 0/1/0

Enters ATM configuration mode for the ATM interface in the specified slot and port.

Step 4 

Router(config-if)# ip address IP-address

Example:

Router(config-if)# ip address 192.168.10.25 255.255.255.0

Assigns an IP address to the ADSL ATM interface.

Step 5 

Router(config-if)# pvc [name] vpi/vci

Example:

Router(config-if)# pvc [name] vpi/vci

Enters atm-virtual-circuit (interface-atm-vc) configuration mode, and configures a new ATM PVC by assigning a name (optional) and virtual path identifier (VPI)/virtual channel identifier (VCI) numbers.

The default traffic shaping is UBR; the default encapsulation is AAL5+LLC/SNAP.

Step 6 

Router(config-if-vc)# protocol ip IP-address

Example:

Router(config-if-vc)# protocol ip 192.168.0.4

(Optional) Enables IP connectivity and create a point-to-point IP address for the virtual circuit (VC).

Step 7 

Router(config-if-vc)# vbr-rt peak-rate average-rate burst

Example:

Router(config-if-vc)# vbr-rt peak-rate average-rate burst

(Optional) Configures the PVC for real-time variable bit rate (VBR) traffic shaping.

Peak rate—Peak information rate (PIR)

Average rate—Average information rate (AIR)

Burst—Burst size in cells

Step 8 

Router(config-if-vc)# encapsulation {aal5autoppp | aal5ciscoppp | aal5mux | aal5nlpid | aal5snap}

Example:

Router(config-if-vc)# encapsulation aal5snap

(Optional) Configures the ATM adaptation layer (AAL) and encapsulation type.

aal5autoppp—Cisco AUTO PPP over AAL5

aal5ciscoppp—Cisco PPP over AAL5

aal5mux—AAL5+MUX

aal5nlpid—AAL5+NLPID

aal5snap—AAL5+LLC/SNAP (the default)

Step 9 

Router(config-if-vc)# exit

Example:

Router(config-if-vc)# exit

Exits from interface-atm-vc configuration mode.

Step 10 

Router(config-if)# dsl operating-mode {ansi-dmt 
| auto | itu-dmt | adsl2 | adsl2+}









or

Router(config-if)# dsl operating-mode {etsi | 
auto | itu-dmt | adsl2 | adsl2+}
Example:

Router(config-if)# dsl operating-mode auto

Configures HWIC-1ADSL to operate in a specified mode:

ansi-dmt—ANSI full rate mode per T1.413, Issue 2)

auto—Automatic detection mode

itu-dmt—ITU full rate mode (ITU G.992.1)

adsl2—ADSL 2 mode per ITU G.992.3

adsl2+—ADSL 2+ mode per ITU G.992.5

Configures HWIC-1ADSLI to operate in a specified mode:

etsi—Alcatel proprietary ETSI mode

auto—Automatic selection mode

itu-dmt—ITU full rate mode (ITU G.992.1)

adsl2—ADSL 2 mode per ITU G.992.3

adsl2+—ADSL 2+ mode per ITU G.992.5


Caution This command is for testing or lab environments only. Using a configuration other than the default configuration for the DSL operating mode can lead to unpredictable behavior on the ADSL line.

Step 11 

Router(config-if)# no shutdown

Example:

Router(config-if)# no shutdown

Activates the ATM interface.

Step 12 

Router(config-if)# exit

Example:

Router(config-if)# exit

Exits from ATM interface configuration mode.

Step 13 

Router(config)# exit

Example:

Router(config)# exit

Exits from global configuration mode.

Configuration Example for ADSL HWICs

This section provides the following configuration example:

VoIP over ATM (AAL5)

VoIP over ATM (AAL5) on the ADSL Interface: Example

The following example shows a Cisco router configured for VoIP over ATM (AAL5) on the ADSL interface with an ADSL HWIC.

Router#
version 12.4
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
no logging buffered
no logging buffered
logging rate-limit console 10 except errors
!
no aaa new-model

resource policy

mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmisnmp-timeout 180
ip subnet-zero
ipcef
!
no ip domain-lookup
!
!
interface FastEthernet0/0
 ip address 10.0.0.1 255.255.0.0
 duplex auto
 speed auto
!
!
interface FastEthernet0/1
 no ip address
 duplex auto
 speed auto
!
interface ATM0/1/0
 ip address 100.0.0.1 255.255.0.0
 no atm ilmi-keepalive
 dsl operating-mode auto
 pvc 1/100
  protocol ip 100.0.0.2 broadcast
!
!
ip classless
!
ip http server
no ip http secure-server
!
!
control-plane
!
!
dial-peer voice 10000 voip
 destination-pattern 10000
 session target ipv4:100.0.0.2
!
!
line con 0
 exec-timeout 0 0
line aux 0
line vty 0 4
 login
!
end

Additional References

The following sections provide references related to ADSL HWICs.

Related Documents

Related Topic
Document Title

Interface Card Installation

Cisco Interface Cards Hardware Installation Guide


Standards

Standards
Title

No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.


MIBs

MIBs
MIBs Link

No new or modified MIBs are supported by this feature, and support for existing MIBs has not been modified by this feature.

To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs


RFCs

RFCs
Title

No new or modified RFCs are supported by this feature, and support for existing RFCs has not been modified by this feature.


Technical Assistance

Description
Link

Technical Assistance Center (TAC) home page, containing 30,000 pages of searchable technical content, including links to products, technologies, solutions, technical tips, and tools. Registered Cisco.com users can log in from this page to access even more content.

http://www.cisco.com/techsupport


Command Reference

This section documents modified commands. All other commands used with this feature are documented in the Cisco IOS Release 12.4T command reference publications.

dsl operating-mode

show diag

dsl operating-mode


Caution This command is for testing or lab environments only. Using a configuration other than the default configuration for the digital subscriber line (DSL) operating mode can lead to unpredictable behavior on the asymmetric digital subscriber line (ADSL).

To modify the operating mode of the digital subscriber line for an ATM interface, use the dsl operating-mode command in interface configuration mode. To reset the operating mode to the default, use the no form of this command.

Cisco WIC-1ADSL

dsl operating-mode {auto | ansi-dmt | itu-dmt | splitterless}

no dsl operating-mode {auto | ansi-dmt | itu-dmt | splitterless}

Cisco WIC-1ADSL-I-DG

dsl operating-mode {auto | etsi | itu-dmt} [tone low]

no dsl operating-mode {auto | etsi | itu-dmt} [tone low]

Cisco HWIC-1ADSL

dsl operating-mode {auto | ansi-dmt | itu-dmt | adsl2 | adsl2+}

no dsl operating-mode {auto | ansi-dmt | itu-dmt | adsl2 | adsl2+}

Cisco HWIC-1ADSLI

dsl operating-mode {auto | etsi | itu-dmt | adsl2 | adsl2+} [tone low]

no dsl operating-mode {auto | etsi | itu-dmt | adsl2 | adsl2+} [tone low]

Syntax Description

auto

Configures the ADSL line after automatic negotiation with the DSLAM located at the Central Office.

ansi-dmt

Configures the ADSL line to train in the ANSI T1.413 Issue 2 mode.

itu-dmt

Configures the ADSL line to train in the G.992.1 mode.

splitterless

Configures the ADSL line to train in the G.992.2 (G.Lite) mode.

etsi

Configures the ADSL line to train in the ETSI mode.

tone low

Enables the WIC-1ADSL-I-DG to use carrier tones 29 through 48. The absence of tone low tells the WIC-1ADSL-I-DG to use carrier tones 33 through 56. The latter tone set is used when the WIC is operating in accordance with Deutsche Telekom specification U-R2.

adsl2

Configures the ADSL line to train in the G.992.3 (adsl2) mode.

adsl2+

Configures the ADSL line to train in the G.992.5 (adsl2+) mode.


Defaults

The default DSL operating mode is auto.

Command Modes

Interface configuration

Command History

Release
Modification

12.1(3)XJ

This command was introduced on the Cisco 1700 series routers.

12.2(2)T

This command was integrated into Cisco IOS Release 12.2(2)T.

12.2(13)ZH

This command was modified to include the keyword splitterless for the Cisco WIC-1ADSL, and syntax (including tone low) for the Cisco WIC-1ADSL-I-DG.

12.2(15)ZJ

The command changes made in Cisco IOS Release 12.2(13)ZH were integrated into Cisco IOS Release 12.2(15)ZJ.

12.3(4)T

The command changes made in Cisco IOS Release 12.2(15)ZJ were integrated into Cisco IOS Release 12.3(4)T.

12.4(4)T

The command was modified for the Cisco HWIC-1ADSL and the Cisco HWIC-1ADSLI to include the keywords adsl2 and adsl2+, and to remove splitterless support for HWICs.


Usage Guidelines


Caution This command is for testing or lab environments only. Using a configuration other than the default configuration for the DSL operating mode can lead to unpredictable behavior on the ADSL line.

Examples

The following example shows how to configure the DSL operating mode for ATM interface 0/0/0:

Router# configure terminal 
Enter configuration commands, one per line. End with CNTL/Z. 
Router(config)# interface atm 0/0/0 
Router(config-if)# dsl operating-mode itu-dmt 
Router(config-if)# end 
Router#

Related Commands

Command
Description

show diag

Displays diagnostic information about the memory on an ADSL WIC, ADSL HWIC, and the ADSL line training log.

show dsl interface atm

Displays information specific to the ADSL for a specified ATM interface.


show diag

To display hardware and diagnostic information for a networking device, use the show diag command in privileged EXEC configuration mode.

show diag [slot-number] [details | summary]

Cisco 7304 Router

show diag [slot-number | chassis | subslot slot/subslot] [details | summary]

Shared Port Adapters

show diag [subslot slot/subslot] [details | summary]

Syntax Description

slot-number

(Optional) Slot number of the interface. If a slot number is not specified, diagnostic information for all slots is displayed.

chassis

(Optional) Cisco 7304 Router

Specifies the display of diagnostic information about the backplane, power supplies, and fan modules.

subslot slot/subslot

(Optional) Shared Port Adapters

Specifies the display of diagnostic information about the shared port adapter (SPA), where:

slot—Chassis slot number.

Refer to the appropriate hardware manual for slot information. For SIPs, refer to the platform-specific SPA hardware installation guide or the corresponding "Identifying Slots and Subslots for SIPs and SPAs" topic in the platform-specific SPA software configuration guide.

subslot—Secondary slot number on a SIP where a SPA is installed.

Refer to the platform-specific SPA hardware installation guide and the corresponding "Specifying the Interface Address on a SPA" topic in the platform-specific SPA software configuration guide for subslot information.

details

(Optional) Displays more details than the normal show diag output.

summary

(Optional) Displays a summary (one line per slot) of the chassis.


Defaults

No default behavior or values

Command Modes

Privileged EXEC

Command History

Release
Modification

11.1CA

This command was introduced.

11.2

This command was integrated into Cisco IOS Release 11.2.

11.2P

This command output was modified for the PA-12E/2FE port adapter, PA-E3 port adapter, and PA-T3 port adapter.

11.2GS

This command was implemented on the Cisco 12000 series Gigabit Switch Routers (GSRs).

12.0

This command was implemented on the Cisco AS5300.

12.0(5)XQ

This command was implemented on the Cisco 1750 router.

12.0(7)T

This command was integrated into Cisco IOS Release 12.0(7)T.

12.1(9)EX

This command was introduced on the Cisco 7300 series routers, and the slot-number argument and chassis keyword were added.

12.2(8)T

This command was implemented for AIC and WIC cards on the Cisco 2600 series routers and the Cisco 3600 series routers.

12.2(13)T

This command was implemented for the AIM-VPN/EPII and AIM-VPN/HPII cards on the Cisco 2691, Cisco 3660, Cisco 3725, and Cisco 3745.

12.2(15)ZJ

This command was implemented for the AIM-VPN/BPII card on the Cisco 2610XM, Cisco 2611XM, Cisco 2620XM, Cisco 2621XM, Cisco 2650XM, and Cisco 2651XM.

12.2(18)S

This command was integrated into Cisco IOS Release 12.2(18)S and implemented on the Cisco 7304 router.

12.3(4)T

Support for the AIM-VPN/BPII card on the Cisco 2600XM series was integrated into Cisco IOS Release 12.3(4)T.

12.2(20)S2

This command was integrated into Cisco IOS Release 12.2(20)S2 and the subslot slot/subslot keyword and arguments were added to support SPAs on the Cisco 7304 router.

12.0(31)S

This command was integrated into Cisco IOS Release 12.0(31)S and the subslot slot/subslot keyword and arguments were added to support SIPs and SPAs on the Cisco 12000 series router.

12.4(4)T

This command was implemented for the HWIC-1ADSL and HWIC-1ADSLI interface cards on the following platforms: Cisco 1800 (modular) series, Cisco 2800 series, and Cisco 3800 series.


Usage Guidelines

Use this command to determine the type of hardware installed in your router, and to show detailed hardware information and EEPROM version information.

This command displays information for the motherboard, WAN interface cards (WICs), voice interface cards (VICs), high-speed WICs (HWICs), ATM interface cards (AICs), advanced integration modules (AIMs), port adapters, shared port adapters (SPAs), modular services cards (MSCs), and SPA interface processors (SIPs).

Cisco 7304 Router Usage Guidelines

For the Cisco 7304 router, this command applies to NSEs, line cards, MSCs, and SPAs.

To display hardware information for an NSE, line card, or MSC in the specified slot, use the slot-number argument. For MSCs, information about the MSC and each of its installed SPAs is displayed.

To display hardware information about the backplane, power supplies, and fan modules, use the chassis keyword.

Shared Port Adapter Usage Guidelines

To display hardware information for an MSC or SIP only in a specified slot, use the slot-number argument.

To display hardware information for a SPA only, use the show diag subslot slot/subslot version of this command.

Examples

Example for a 1-Port T3 Serial Port Adapter

The following is sample output from the show diag command for a 1-port T3 serial port adapter in chassis slot 1 on a Cisco 7200 series router:

Router# show diag 1

Slot 1:
        Physical slot 1, ~physical slot 0xE, logical slot 1, CBus 0
        Microcode Status 0x4
        Master Enable, LED, WCS Loaded
        Board is analyzed
        Pending I/O Status: None
        EEPROM format version 1
        VIP2 controller, HW rev 2.4, board revision D0
        Serial number: 04372053  Part number: 73-1684-03
        Test history: 0x00        RMA number: 00-00-00
        Flags: cisco 7000 board; 7500 compatible

        EEPROM contents (hex):
          0x20: 01 15 02 04 00 42 B6 55 49 06 94 03 00 00 00 00
          0x30: 68 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

        Slot database information:
        Flags: 0x4      Insertion time: 0x14A8 (5d02h ago)

        Controller Memory Size: 16 MBytes DRAM, 1024 KBytes SRAM

        PA Bay 0 Information:
                T3 Serial PA, 1 ports
                EEPROM format version 1
                HW rev FF.FF, Board revision UNKNOWN
                Serial number: 4294967295  Part number: 255-65535-255

Examples for a Cisco 12000 Series Internet Router

The following is sample output from the show diag command on a Cisco 12000 series Internet router:

Router# show diag 3

SLOT 3  (RP/LC 3 ): 4 Port Packet Over SONET OC-3c/STM-1 Multi Mode
  MAIN: type 33,  00-0000-00 rev 70 dev 0
        HW config: 0x01    SW key: 00-00-00
  PCA:  73-2147-02 rev 94 ver 2
        HW version 1.0  S/N 04499695
  MBUS: MBUS Agent (1)  73-2146-05 rev 73 dev 0
        HW version 1.1  S/N 04494882
        Test hist: 0x00    RMA#: 00-00-00    RMA hist: 0x00
  DIAG: Test count: 0x05000001    Test results: 0x00000000
  MBUS Agent Software version 01.27 (RAM) using CAN Bus A
  ROM Monitor version 00.0D
  Fabric Downloader version used 00.0D (ROM version is 00.0D)
  Board is analyzed 
  Board State is Line Card Enabled (IOS  RUN )
  Insertion time: 00:00:10 (00:04:51 ago)
  DRAM size: 33554432 bytes
  FrFab SDRAM size: 67108864 bytes
  ToFab SDRAM size: 16777216 bytes

The following is sample output from the show diag command with the summary keyword:

Router# show diag summary

SLOT 0  (RP/LC 0 ): Route Processor
SLOT 2  (RP/LC 2 ): 4 Port Packet Over SONET OC-3c/STM-1 Single Mode
SLOT 4  (RP/LC 4 ): 4 Port Packet Over SONET OC-3c/STM-1 Single Mode
SLOT 7  (RP/LC 7 ): 4 Port Packet Over SONET OC-3c/STM-1 Single Mode
SLOT 9  (RP/LC 9 ): 4 Port Packet Over SONET OC-3c/STM-1 Single Mode
SLOT 11 (RP/LC 11): 4 Port Packet Over SONET OC-3c/STM-1 Single Mode
SLOT 16 (CSC 0   ): Clock Scheduler Card
SLOT 17 (CSC 1   ): Clock Scheduler Card
SLOT 18 (SFC 0   ): Switch Fabric Card
SLOT 19 (SFC 1   ): Switch Fabric Card
SLOT 20 (SFC 2   ): Switch Fabric Card
SLOT 24 (PS A1   ): AC Power Supply
SLOT 26 (PS B1   ): AC Power Supply
SLOT 28 (TOP FAN ): Blower Module
SLOT 29 (BOT FAN ): Blower Module

The following is sample output from the show diag command with the details keyword:

Router# show diag 4 details 

SLOT 4  (RP/LC 4): 4 Port Packet Over SONET OC-3c/STM-1 Single Mode
  MAIN: type 33,  800-2389-01 rev 71 dev 16777215
        HW config: 0x00    SW key: FF-FF-FF
  PCA:  73-2275-03 rev 75 ver 3
        HW version 1.1  S/N 04529465
  MBUS: MBUS Agent (1)  73-2146-06 rev 73 dev 0
        HW version 1.1  S/N 04541395
        Test hist: 0xFF    RMA#: FF-FF-FF    RMA hist: 0xFF
  DIAG: Test count: 0x05000001    Test results: 0x00000000
  EEPROM contents (hex):
  00: 01 00 01 00  49 00 08 62  06 03 00 00  00 FF FF FF
  10: 30 34 35 34  31 33 39 35  FF FF FF FF  FF FF FF FF
  20: 01 01 00 00  00 00 00 FF  FF FF FF FF  FF FF FF FF
  30: A5 FF A5 A5  A5 A5 FF A5  A5 A5 A5 A5  A5 A5 A5 A5
  40: 00 21 01 01  00 49 00 08  E3 03 05 03  00 01 FF FF
  50: 03 20 00 09  55 01 01 FF  FF FF 00 FF  FF FF FF FF
  60: 30 34 35 32  39 34 36 35  FF FF FF FF  FF FF FF FF
  70: FF FF FF FF  FF FF FF FF  05 00 00 01  00 00 00 00
  MBUS Agent Software version 01.24 (RAM)
  Fabric Downloader version 00.0D
  Board is analyzed
  Flags: 0x4
  Board State is Line Card Enabled (IOS  RUN)
  Insertion time: 00:00:10 (00:04:51 ago)
  DRAM size: 33554432 bytes
  FrFab SDRAM size: 67108864 bytes
  ToFab SDRAM size: 16777216 bytes

Example for an ATM SAR AIM in a Cisco 3660

The following is sample output from the show diag command for one ATM Segmentation and Reassembly (SAR) AIM in a Cisco 3660 router:

Router# show diag 0

3660 Chassis type: ENTERPRISE

c3600 Backplane EEPROM:
	Hardware Revision        : 1.0
	Top Assy. Part Number    : 800-04740-02
.
.
.
ATM AIM: 1
	ATM AIM module with SAR only (no DSPs)
	Hardware Revision        : 1.0
	Top Assy. Part Number    : 800-03700-01
	Board Revision           : A0
	Deviation Number         : 0-0
	Fab Version              : 02
	PCB Serial Number        : JAB9801ABCD

Example for an NM-AIC-64 Installed in a Cisco 2611

The following is sample output from the show diag command for a Cisco 2611 router with the NM-AIC-64 installed.

Router# show diag 

Slot 0: 
C2611 2E Mainboard Port adapter, 2 ports 
Port adapter is analyzed  
Port adapter insertion time unknown 
EEPROM contents at hardware discovery: 
Hardware Revision : 2.3 
PCB Serial Number : JAD044808SG (1090473337) 
Part Number : 73-2840-13 
RMA History : 00 
RMA Number : 0-0-0-0 
Board Revision : C0 
Deviation Number : 0-0 
EEPROM format version 4 
EEPROM contents (hex): 
0x00: 04 FF 40 00 92 41 02 03 C1 18 4A 41 44 30 34 34 
0x10: 38 30 38 53 47 20 28 31 30 39 30 34 37 33 33 33 
0x20: 37 29 82 49 0B 18 0D 04 00 81 00 00 00 00 42 43 
0x30: 30 80 00 00 00 00 FF FF FF FF FF FF FF FF FF FF 
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 
 
Slot 1: 
NM_AIC_64 Port adapter, 3 ports 
Port adapter is analyzed  
Port adapter insertion time unknown 
EEPROM contents at hardware discovery: 
Hardware Revision : 1.0 
Part Number : 74-1923-01 
Board Revision : 02 
PCB Serial Number : DAN05060012 
EEPROM format version 4 
EEPROM contents (hex): 
0x00: 04 FF 40 02 55 41 01 00 82 4A 07 83 01 42 30 32 
0x10: C1 8B 44 41 4E 30 35 30 36 30 30 31 32 FF FF FF 
0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 

Table 2 describes significant fields shown in the display.

Table 2 show diag (AIC) Field Descriptions

Field
Description

C2611 2E Mainboard Port adapter, 2 ports

Line card type; number of ports available.

Port adapter is analyzed

The system has identified the port adapter.

Port adapter insertion time

Elapsed time since insertion.

Hardware Revision

Version number of the port adapter.

PCB Serial Number

Serial number of the printed circuit board.

Part Number

Part number of the port adapter.

RMA History

Counter that indicates how many times the port adapter has been returned and repaired.

RMA Number

Return material authorization number, which is an administrative number assigned if the port adapter needs to be returned for repair.

Board Revision

Revision number (signifying a minor revision) of the port adapter.

Deviation Number

Revision number (signifying a minor deviation) of the port adapter.

EEPROM format version

Version number of the EEPROM format.

EEPROM contents (hex)

Dumps of EEPROM programmed data.


Example for an AIM-VPN in a Cisco 2611XM

The following example shows how to obtain hardware information about an installed AIM-VPN on the Cisco 2611XM router.

Router# show diag 0

Encryption AIM 1:

Hardware Revision :1.0

Top Assy. Part Number :800-03700-01

Board Revision :A0

Deviation Number :0-0

Fab Version :02

PCB Serial Number :JAB9801ABCD

RMA Test History :00

RMA Number :0-0-0-0

RMA History :00

EEPROM format version 4

EEPROM contents (hex):

0x00:04 FF 40 03 0B 41 01 00 C0 46 03 20 00 0E 74 01

0x10:42 41 30 80 00 00 00 00 02 02 C1 8B 4A 41 42 39

0x20:38 30 31 41 42 43 44 03 00 81 00 00 00 00 04 00

0x30:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x40:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x50:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Table 3 describes significant fields shown in the display.

Table 3 show diag (AIM-VPN) Field Descriptions

Field
Description

Hardware Revision

Version number of the port adapter.

Top Assy. Part Number

Part number of the port adapter.

Board Revision

Revision number (signifying a minor revision) of the port adapter.

Deviation Number

Revision number (signifying a minor deviation) of the port adapter.

PCB Serial Number

Serial number of the printed circuit board.

RMA Number

Return material authorization number, which is an administrative number assigned if the port adapter needs to be returned for repair.

RMA History

Counter that indicates how many times the port adapter has been returned and repaired.

EEPROM format version

Version number of the EEPROM format.

EEPROM contents (hex)

Dumps of EEPROM programmed data.


Example for an MSC-100 on the Cisco 7304 Router

The following is sample output from the show diag slot-number version of the command for an MSC-100 located in slot number 4 on a Cisco 7304 router. Information about the MSC is followed by information for its associated SPAs:

Router# show diag 4
Slot 4:
        7304-MSC-100 SPA Carrier Card Line Card
        Line Card state: Active
        Insertion time: 00:08:49 ago
        Bandwidth points: 4000000
        EEPROM contents at hardware discovery:
        Hardware Revision        : 0.18
        Boot Time out            : 0000
        PCB Serial Number        : CSJ07288905
        Part Number              : 73-8789-01
        Board Revision           : A0
        Fab Version              : 02
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Deviation Number         : 0-0
        Product Number           : 7304-MSC-100
        Top Assy. Part Number    : 68-1163-04
        Manufacturing Test Data  : 00 00 00 00 00 00 00 00
        Field Diagnostics Data   : 00 00 00 00 00 00 00 00
        Calibration Data         : Minimum: 0 dBmV, Maximum: 0 dBmV
              Calibration values :
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 04 50 41 00 12 46 00 00 C1 8B 43 53 4A
          0x10: 30 37 32 38 38 39 30 35 82 49 22 55 01 42 41 30
          0x20: 02 02 03 00 81 00 00 00 00 04 00 80 00 00 00 00
          0x30: CB 94 37 33 30 34 2D 4D 53 43 2D 31 30 30 20 20
          0x40: 20 20 20 20 20 20 87 44 04 8B 04 C4 08 00 00 00
          0x50: 00 00 00 00 00 C5 08 00 00 00 00 00 00 00 00 C8
          0x60: 09 00 00 00 00 00 00 00 00 00 C7 7C F6 44 3F 30
          0x70: 00 00 00 00 00 00 00 00 00 00 00 00 02 EE FF C8
          0x80: C8 37 26 05 DC 64 28 1E 37 26 09 C4 64 32 28 32
          0x90: DD 0C E4 64 32 28 43 24 2E E0 AA 82 64 F4 24 00
          0xA0: 00 00 00 00 00 00 F0 2E FF FF FF FF FF FF FF FF
          0xB0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0xC0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0xD0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x100: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x110: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x120: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x130: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x140: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x150: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x160: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x170: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x180: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x190: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x1A0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x1B0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x1C0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x1D0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x1E0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x1F0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
        FPGA information:
          Current FPGA version     : 00.23
          IOS bundled FPGA version : 00.23
        CPLD version     : 01.02

Subslot 4/1:
        Shared port adapter: SPA-4FE-7304, 4 ports
        State: ok
        Insertion time: 00:15:13 ago
        Bandwidth: 400000 kbps
        EEPROM contents:
.
.
.

Examples for Shared Port Adapters on the Cisco 7304 Router

The following is sample output from the show diag subslot command for a 4-Port 10/100 Fast Ethernet SPA located in the bottom subslot (1) of the MSC that is installed in slot 4 on a Cisco 7304 router:

Router# show diag subslot 4/1
Subslot 4/1:
        Shared port adapter: SPA-4FE-7304, 4 ports
        Info: hw-ver=0x100, sw-ver=0x0 fpga-ver=0x0
        State: ok
        Insertion time: 23:20:42 ago
        Bandwidth: 400000 kbps
        EEPROM contents:
        Hardware Revision        : 1.0
        Boot Time out            : 0190
        PCB Serial Number        : JAB073204G5
        Part Number              : 73-8717-03
        73/68 Level Revision     : 01
        Fab Version              : 02
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Deviation Number         : 0
        Product Number           : SPA-4FE-7304
        Product Version Id       : V01
        Top Assy. Part Number    : 68-2181-01
        73/68 Level Revision     : A0
        CLEI Code                : CNS9420AAA
        Base MAC Address         : 0000.0000.0000
        MAC Address block size   : 1024
        Manufacturing Test Data  : 00 00 00 00 00 00 00 00
        Field Diagnostics Data   : 00 00 00 00 00 00 00 00
        Field Diagnostics Data   : 00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00
        Calibration Data         : Minimum: 0 dBmV, Maximum: 0 dBmV
              Calibration values :
        Power Consumption        : 160000mW max
                          Mode 1 : 0mW
                          Mode 2 : 0mW
                          Mode 3 : 0mW
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 04 35 41 01 00 46 01 90 C1 8B 4A 41 42
          0x10: 30 37 33 32 30 34 47 35 82 49 22 0D 03 8A 30 31
          0x20: 20 20 02 02 03 00 81 00 00 00 00 04 00 88 00 00
          0x30: 00 00 CB 94 53 50 41 2D 34 46 45 2D 37 33 30 34
          0x40: 20 20 20 20 20 20 20 20 89 56 30 31 20 87 44 08
          0x50: 85 01 8A 41 30 20 20 C6 8A 43 4E 53 39 34 32 30
          0x60: 41 41 41 CF 06 00 00 00 00 00 00 43 04 00 C4 08
          0x70: 00 00 00 00 00 00 00 00 C5 08 00 00 00 00 00 00
          0x80: 00 00 F4 00 64 00 00 00 00 00 00 00 00 00 00 00
          0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0xE0: 00 00 00 00 00 00 00 00 00 C8 09 00 00 00 00 00
          0xF0: 00 00 00 00 D7 08 3E 80 00 00 00 00 00 00 F3 00
          0x100: 41 01 08 F6 48 43 34 F6 49 44 35 02 31 04 B0 B4
          0x110: A0 8C 00 00 05 DC 64 46 32 00 00 07 08 64 46 32
          0x120: 00 00 09 C4 64 46 32 00 00 0C E4 64 46 32 00 00
          0x130: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 FE 02
          0x140: F2 A6 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x150: CC A0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0x160: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0x170: 00 00 D4 A0 00 00 00 00 00 00 00 00 00 00 00 00
          0x180: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0x190: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0x1A0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0x1B0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0x1C0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0x1D0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0x1E0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0x1F0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
        FPGA version:
          Software version : 04.17
          Hardware version : 04.17

The following is sample output from the show diag subslot command for a 2-Port 10/100/1000 Gigabit Ethernet SPA located in the top subslot (0) of the MSC that is installed in slot 4 on a Cisco 7304 router:

Router# show diag subslot 4/0
Subslot 4/0:
        Shared port adapter: SPA-2GE-7304, 2 ports
        Info: hw-ver=0x17, sw-ver=0x0 fpga-ver=0x0
        State: ok
        Insertion time: 00:08:47 ago
        Bandwidth: 2000000 kbps
        EEPROM contents:
        Hardware Revision        : 0.23
        Boot Time out            : 0190
        PCB Serial Number        : JAB073406YH
        Part Number              : 73-8792-02
        73/68 Level Revision     : 01
        Fab Version              : 02
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Deviation Number         : 0
        Product Number           : SPA-2GE-7304
        Product Version Id       : V01
        Top Assy. Part Number    : 68-2181-01
        73/68 Level Revision     : A0
        CLEI Code                : CNS9420AAA
        Base MAC Address         : 0000.0000.0000
        MAC Address block size   : 1024
        Manufacturing Test Data  : 00 00 00 00 00 00 00 00
        Field Diagnostics Data   : 00 00 00 00 00 00 00 00
        Field Diagnostics Data   : 00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00 00 00 00 00
                                   00 00 00 00
        Calibration Data         : Minimum: 0 dBmV, Maximum: 0 dBmV
              Calibration values :
        Power Consumption        : 160000mW max
                          Mode 1 : 0mW
                          Mode 2 : 0mW
                          Mode 3 : 0mW
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 04 36 41 00 17 46 01 90 C1 8B 4A 41 42
          0x10: 30 37 33 34 30 36 59 48 82 49 22 58 02 8A 30 31
          0x20: 20 20 02 02 03 00 81 00 00 00 00 04 00 88 00 00
          0x30: 00 00 CB 94 53 50 41 2D 32 47 45 2D 37 33 30 34
          0x40: 20 20 20 20 20 20 20 20 89 56 30 31 20 87 44 08
          0x50: 85 01 8A 41 30 20 20 C6 8A 43 4E 53 39 34 32 30
          0x60: 41 41 41 CF 06 00 00 00 00 00 00 43 04 00 C4 08
          0x70: 00 00 00 00 00 00 00 00 C5 08 00 00 00 00 00 00
          0x80: 00 00 F4 00 64 00 00 00 00 00 00 00 00 00 00 00
          0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0xE0: 00 00 00 00 00 00 00 00 00 C8 09 00 00 00 00 00
          0xF0: 00 00 00 00 D7 08 3E 80 00 00 00 00 00 00 F3 00
          0x100: 41 01 08 F6 48 43 34 F6 49 44 35 02 31 03 E8 B4
          0x110: A0 8C 37 26 05 DC 64 46 32 37 26 07 08 64 46 32
          0x120: 37 26 09 C4 64 46 32 32 DD 0C E4 64 46 32 43 24
          0x130: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 FE 02
          0x140: EF E2 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x150: CC A0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0x160: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0x170: 00 00 D4 A0 00 00 00 00 00 00 00 00 00 00 00 00
          0x180: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0x190: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0x1A0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0x1B0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0x1C0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0x1D0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0x1E0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
          0x1F0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
        FPGA version:
          Software version : 04.17
          Hardware version : 04.17

Examples for a Shared Port Adapter on a Cisco 12000 Series Router

The following is sample output from the show diag subslot command for the 1-Port OC-192c/STM-64c POS/RPR XFP SPA in subslot 1 of the SIP located in chassis slot 1 on a Cisco 12000 series router:

Router# show diag subslot 1/1
SUBSLOT  1/1 (SPA-OC192POS-XFP): 1-port OC192/STM64 POS/RPR XFP Optics Shared Port Adapter
       Product Identifier (PID) : SPA-OC192POS-XFP   
       Version Identifier (VID) : V01
       PCB Serial Number        : PRTA1304061
       Top Assy. Part Number    : 68-2190-01
       Top Assy. Revision       : A0        
       Hardware Revision        : 2.0
       CLEI Code                : UNASSIGNED
       Insertion Time           : 00:00:10 (13:14:17 ago)
       Operational Status       : ok

Table 3 describes the significant fields shown in the display.

Table 4 show diag subslot Field Descriptions 

Field
Description

Product Identifier (PID)

Product number of the SPA.

Version Identifier (VID)

Version number of the SPA.

PCB Serial Number

Serial number of the printed circuit board.

Top Assy. Part Number

Part number of the SPA.

Top Assy. Revision

Revision number (signifying a minor revision) of the SPA.

Hardware Revision

Revision number (signifying a minor revision) of the SPA hardware.

CLEI Code

Common Language Equipment Identification number.

Insertion Time

Time when the SPA was installed, and elapsed time between that insertion time and the current time.

Operational Status

Current status of the SPA. For more information about the status field descriptions, refer to the show hw-module subslot oir command.


The following is sample output from the show diag subslot details command for the 1-Port OC-192c/STM-64c POS/RPR XFP SPA in subslot 1 of the SIP located in chassis slot 1 on a Cisco 12000 series router:

Router# show diag subslot 1/1 details
SUBSLOT  1/1 (SPA-OC192POS-XFP): 1-port OC192/STM64 POS/RPR XFP Optics Shared Port Adapter
       EEPROM version           : 4
       Compatible Type          : 0xFF
       Controller Type          : 1100
       Hardware Revision        : 2.0
       Boot Timeout             : 400 msecs
       PCB Serial Number        : PRTA1304061
       PCB Part Number          : 73-8546-01
       PCB Revision             : A0        Fab Version              : 01
       RMA Test History         : 00
       RMA Number               : 0-0-0-0
       RMA History              : 00
       Deviation Number         : 0
       Product Identifier (PID) : SPA-OC192POS-XFP   
       Version Identifier (VID) : V01
       Top Assy. Part Number    : 68-2190-01
       Top Assy. Revision       : A0        IDPROM Format Revision   : 36
       System Clock Frequency   : 00 00 00 00 00 00 00 00
                                  00 00 00 00 00 00 00 00
                                  00 00 00 00 00 00
       CLEI Code                : UNASSIGNED
       Base MAC Address         : 00 00 00 00 00 00
       MAC Address block size   : 0
       Manufacturing Test Data  : 00 00 00 00 00 00 00 00
       Field Diagnostics Data   : 00 00 00 00 00 00 00 00
       Calibration Data         : Minimum: 0 dBmV, Maximum: 0 dBmV
             Calibration values :
       Power Consumption        : 11000 mWatts (Maximum)
       Environment Monitor Data : 03 30 04 B0 46 32 07 08
                                  46 32 09 C4 46 32 0C E4
                                  46 32 13 88 46 32 07 08
                                  46 32 EB B0 50 3C 00 00
                                  00 00 00 00 00 00 00 00
                                  00 00 00 00 00 00 00 00
                                  00 00 FE 02 F6 AC
       Processor Label          : 00 00 00 00 00 00 00
       Platform features        : 00 00 00 00 00 00 00 00
                                  00 00 00 00 00 00 00 00
                                  00 00 00 00 00 00 00 00
                                  00 00 00 00 00 00 00
       Asset ID                 :
       Asset Alias              :
       Insertion Time           : 00:00:10 (13:14:24 ago)
       Operational Status       : ok

Example for a SPA Interface Processor on a Cisco 12000 Series Router

The following is sample output from the show diag command for a SIP located in chassis slot 2 on a Cisco 12000 series router:

Router# show diag 2 

SLOT 2  (RP/LC 2 ): Modular 10G SPA Interface Card
  MAIN: type 149,  800-26270-01 rev 84
        Deviation: 0
        HW config: 0x00    SW key: 00-00-00
  PCA:  73-9607-01 rev 91 ver 1
        Design Release 1.0  S/N SAD08460678
  MBUS: Embedded Agent
        Test hist: 0x00    RMA#: 00-00-00    RMA hist: 0x00
  DIAG: Test count: 0x00000000    Test results: 0x00000000
  FRU:  Linecard/Module: 12000-SIP-650
  FRU:  Linecard/Module: 12000-SIP-650
        Processor Memory: MEM-LC5-1024=(Non-Replaceable)
        Packet Memory: MEM-LC5-PKT-256=(Non-Replaceable)
  L3 Engine: 5 - ISE OC192 (10 Gbps)
  MBUS Agent Software version 1.114 (RAM) (ROM version is 3.4)
  ROM Monitor version 255.255
  Fabric Downloader version used 3.7 (ROM version is 255.255)
  Primary clock is CSC 1
  Board is analyzed 
  Board State is Line Card Enabled (IOS  RUN )
  Insertion time: 1d00h (2d08h ago)
  Processor Memory size: 1073741824 bytes
  TX Packet Memory size: 268435456 bytes, Packet Memory pagesize: 32768 bytes
  RX Packet Memory size: 268435456 bytes, Packet Memory pagesize: 32768 bytes
  0 crashes since restart

  SPA Information:
        subslot 2/0: SPA-OC192POS-XFP (0x44C), status is ok
        subslot 2/1: Empty
        subslot 2/2: Empty
        subslot 2/3: Empty

Example for ADSL HWICs

The following is sample output from the show diag command for a Cisco 2811 router with HWIC-1ADSL installed in slot 1 and HWIC-1ADSLI installed in slot 2. Each HWIC has a daughtercard as part of its assembly. The command results below give the output from the HWIC followed by the output from its daughtercard.

Router# show diag 0

Slot 0:

C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports
        Port adapter is analyzed 
        Port adapter insertion time unknown
        Onboard VPN             : v2.2.0
        EEPROM contents at hardware discovery:
        PCB Serial Number        : FOC09052HHA
        Hardware Revision        : 2.0
        Top Assy. Part Number    : 800-21849-02
        Board Revision           : B0
        Deviation Number         : 0
        Fab Version              : 06
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Processor type           : 87 
        Hardware date code       : 20050205
        Chassis Serial Number    : FTX0908A0B0
        Chassis MAC Address      : 0013.1ac2.2848
        MAC Address block size   : 24
        CLEI Code                : CNMJ7N0BRA
        Product (FRU) Number     : CISCO2811      
        Part Number              : 73-7214-09
        Version Identifier       :   NA 
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF C1 8B 46 4F 43 30 39 30 35 32 48 48 41 40
          0x10: 03 E7 41 02 00 C0 46 03 20 00 55 59 02 42 42 30
          0x20: 88 00 00 00 00 02 06 03 00 81 00 00 00 00 04 00
          0x30: 09 87 83 01 31 F1 1D C2 8B 46 54 58 30 39 30 38
          0x40: 41 30 42 30 C3 06 00 13 1A C2 28 48 43 00 18 C6
          0x50: 8A 43 4E 4D 4A 37 4E 30 42 52 41 CB 8F 43 49 53
          0x60: 43 4F 32 38 31 31 20 20 20 20 20 20 82 49 1C 2E
          0x70: 09 89 20 20 4E 41 D9 02 40 C1 FF FF FF FF FF FF

WIC Slot 1:
        ADSL over POTS
        Hardware Revision        : 7.0
        Top Assy. Part Number    : 800-26247-01
        Board Revision           : 01 
        Deviation Number         : 0
        Fab Version              : 07
        PCB Serial Number        : FHH093600D4
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Product (FRU) Number     : HWIC-1ADSL          
        Version Identifier       : V01 
        CLEI Code                : 
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 04 C8 41 07 00 C0 46 03 20 00 66 87 01
          0x10: 42 30 31 88 00 00 00 00 02 07 C1 8B 46 48 48 30
          0x20: 39 33 36 30 30 44 34 03 00 81 00 00 00 00 04 00
          0x30: CB 94 48 57 49 43 2D 31 41 44 53 4C 20 20 20 20
          0x40: 20 20 20 20 20 20 89 56 30 31 20 D9 02 40 C1 C6
          0x50: 8A FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

        EM Slot 0:
        ADSL over POTS non-removable daughtercard
        Hardware Revision        : 5.0 
        Part Number              : 73-9307-05
        Board Revision           : 03
        Deviation Number         : 0
        Fab Version              : 05
        PCB Serial Number        : FHH0936006E
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Fab Part Number          : 28-6607-05
        Manufacturing Test Data  : 00 00 00 00 00 00 00 00 
        Field Diagnostics Data   : 00 00 00 00 00 00 00 00 
        Connector Type           : 01
        Version Identifier       : V01 
        Product (FRU) Number     :  
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 04 7A 41 05 00 82 49 24 5B 05 42 30 33
          0x10: 88 00 00 00 00 02 05 C1 8B 46 48 48 30 39 33 36
          0x20: 30 30 36 45 03 00 81 00 00 00 00 04 00 85 1C 19
          0x30: CF 05 C4 08 00 00 00 00 00 00 00 00 C5 08 00 00
          0x40: 00 00 00 00 00 00 05 01 89 56 30 31 20 FF FF FF
          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

WIC Slot 2:
        ADSL over ISDN
        Hardware Revision        : 7.0
        Top Assy. Part Number    : 800-26248-01
        Board Revision           : 01
        Deviation Number         : 0
        Fab Version              : 07
        PCB Serial Number        : FHH093600DA
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Product (FRU) Number     : HWIC-1ADSLI         
        Version Identifier       : V01 
        CLEI Code                : 
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 04 C9 41 07 00 C0 46 03 20 00 66 88 01
          0x10: 42 30 31 88 00 00 00 00 02 07 C1 8B 46 48 48 30
          0x20: 39 33 36 30 30 44 41 03 00 81 00 00 00 00 04 00
          0x30: CB 94 48 57 49 43 2D 31 41 44 53 4C 49 20 20 20
          0x40: 20 20 20 20 20 20 89 56 30 31 20 D9 02 40 C1 C6 
          0x50: 8A FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

        EM Slot 0:
        ADSL over ISDN non-removable daughtercard
        Hardware Revision        : 5.0
        Part Number              : 73-9308-05
        Board Revision           : 03
        Deviation Number         : 0
        Fab Version              : 05
        PCB Serial Number        : FHH0936008M
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Fab Part Number          : 28-6607-05
        Manufacturing Test Data  : 00 00 00 00 00 00 00 00 
        Field Diagnostics Data   : 00 00 00 00 00 00 00 00 
        Connector Type           : 01
        Version Identifier       : V01 
        Product (FRU) Number     :  
        EEPROM format version 4
        EEPROM contents (hex): 
          0x00: 04 FF 40 04 7B 41 05 00 82 49 24 5C 05 42 30 33
          0x10: 88 00 00 00 00 02 05 C1 8B 46 48 48 30 39 33 36
          0x20: 30 30 38 4D 03 00 81 00 00 00 00 04 00 85 1C 19
          0x30: CF 05 C4 08 00 00 00 00 00 00 00 00 C5 08 00 00
          0x40: 00 00 00 00 00 00 05 01 89 56 30 31 20 FF FF FF
          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Related Commands

Command
Description

dsl operating-mode (ADSL)

Modifies the operating mode of the digital subscriber line for an ATM interface.

show dsl interface atm

Shows all of the ADSL-specific information for a specified ATM interface.

show controllers fastethernet

Displays Fast Ethernet interface information, transmission statistics and errors, and applicable MAC destination address and VLAN filtering tables.

show controllers gigabitethernet

Displays Gigabit Ethernet interface information, transmission statistics and errors, and applicable MAC destination address and VLAN filtering tables.