Dial Peer Configuration Guide, Cisco IOS XE Release 3S
Modes for Dial-Peer Configuration
Downloads: This chapterpdf (PDF - 1.2MB) The complete bookPDF (PDF - 3.21MB) | The complete bookePub (ePub - 594.0KB) | Feedback

Modes for Dial-Peer Configuration

Modes for Dial-Peer Configuration

You can manipulate a dial peer by configuring relevant commands globally, at a dial-peer level, or in a voice class that is then applied to a dial peer.

How to Configure Modes for Dial-Peer Configuration

Entering Dial-Peer Configuration Mode

SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    dial-peer voice number voip

    4.    Enter a command to configure dial-peer behavior.

    5.    exit


DETAILED STEPS
     Command or ActionPurpose
    Step 1enable


    Example:
    Device> enable
     

    Enables privileged EXEC mode. Enter your password if prompted.

     
    Step 2configure terminal


    Example:
    Device# configure terminal
     

    Enters global configuration mode.

     
    Step 3dial-peer voice number voip


    Example:
     
    Device(config)# dial-peer voice 2 voip
     

    Enters dial-peer configuration mode for the specified VoIP dial peer.

     
    Step 4Enter a command to configure dial-peer behavior.    
    Step 5exit


    Example:
    Device(config-dial-peer)# exit
     

    Exits dial-peer configuration mode and returns to privileged EXEC mode.

     

    Entering Global VoIP Configuration Mode

    SUMMARY STEPS

      1.    enable

      2.    configure terminal

      3.    voice service voip

      4.    Enter a command to configure dial-peer behavior.

      5.    exit


    DETAILED STEPS
       Command or ActionPurpose
      Step 1enable


      Example:
      Device> enable
       

      Enables privileged EXEC mode. Enter your password if prompted.

       
      Step 2configure terminal


      Example:
      Device# configure terminal
       

      Enters global configuration mode.

       
      Step 3voice service voip


      Example:
      Device(config)# voice service voip
       

      Enters global VoIP configuration mode.

       
      Step 4Enter a command to configure dial-peer behavior.    
      Step 5exit


      Example:
      Device(config-voi-serv)# exit
       

      Exits global VoIP configuration current mode.

       

      Using Voice Classes to Modify Dial-Peer Behavior

      SUMMARY STEPS

        1.    enable

        2.    configure terminal

        3.    voice class media tag

        4.    Enter a command to configure dial-peer behavior.

        5.    dial-peer voice tag voip

        6.    voice class media tag

        7.    exit


      DETAILED STEPS
         Command or ActionPurpose
        Step 1enable


        Example:
        Device> enable
         

        Enables privileged EXEC mode. Enter your password if prompted.

         
        Step 2configure terminal


        Example:
        Device# configure terminal
         

        Enters global configuration mode.

         
        Step 3voice class media tag


        Example:
        Device(config)# voice class media 1
         

        Enters voice-class configuration mode and assign an identification tag for a media voice class.

         
        Step 4Enter a command to configure dial-peer behavior.    
        Step 5dial-peer voice tag voip


        Example:
        Device(config-class)# dial-peer voice 2 voip
         

        Enters dial-peer configuration mode for the dial peer of your choice. You will apply the voice class on this dial peer.

         
        Step 6voice class media tag


        Example:
        Device(config-dial-peer)# voice class media 1
         

        Applies the voice class to this dial peer. The behavior defined in the voice class is now applicable to the dial peer.

         
        Step 7exit


        Example:
        Device(config-dial-peer)# exit
         

        Exit dial-peer configuration mode and returns to privileged EXEC mode.