Authentication, Authorization, and Accounting Configuration Guide, Cisco IOS Release 15SY
AAA-SERVER-MIB Set Operation
Downloads: This chapterpdf (PDF - 1.3MB) The complete bookPDF (PDF - 4.02MB) | The complete bookePub (ePub - 713.0KB) | Feedback

AAA-SERVER-MIB Set Operation

AAA-SERVER-MIB Set Operation

The AAA-SERVER-MIB Set Operation feature allows the authentication, authorization, and accounting (AAA) server configuration to be extended or expanded by using the CISCO-AAA-SERVER-MIB to create and add new AAA servers, modify the “KEY” under the CISCO-AAA-SERVER-MIB, and delete the AAA server configuration.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Prerequisites for AAA-SERVER-MIB Set Operation

AAA must have been enabled on the router, that is, the aaa new-model command must have been configured. If this configuration has not been accomplished, the set operation fails.

Restrictions for AAA-SERVER-MIB Set Operation

Currently, the CISCO SNMP set operation is supported only for the RADIUS protocol. Therefore, only RADIUS servers in global configuration mode can be added, modified, or deleted.

Information About AAA-SERVER-MIB Set Operation

CISCO-AAA-SERVER-MIB

The CISCO-AAA-SERVER-MIB provides that statistics reflect both the state of the AAA server operation with the server itself and of AAA communications with external servers. The CISCO-AAA-SERVER-MIB provides the following information:

  • Statistics for each AAA operation

  • Status of servers that are providing AAA functions

  • Identities of external AAA servers

CISCO-AAA-SERVER-MIB Set Operation

Before Cisco IOS Release 12.4(4)T, the CISCO-AAA-SERVER-MIB supported only the “get” operation. Effective with this release, the CISCO-AAA-SERVER-MIB supports the set operation. With the set operation, you can do the following:

  • Create or add a new AAA server.

  • Modify the KEY under the CISCO-AAA-SERVER-MIB. This “secret key” is used for secure connectivity to the AAA server, which is present with the network access server (NAS) and the AAA server.

  • Delete the AAA server configuration.

How to Configure AAA-SERVER-MIB Set Operation

Configuring AAA-SERVER-MIB Set Operations

No special configuration is required for this feature. The Simple Network Management Protocol (SNMP) framework can be used to manage MIBs. See the Additional References section for a reference to configuring SNMP.

Verifying SNMP Values

SNMP values can be verified by performing the following steps.

SUMMARY STEPS

    1.    enable

    2.    show running-config | include radius-server host

    3.    show aaa servers


DETAILED STEPS
     Command or ActionPurpose
    Step 1 enable


    Example:
    Router> enable
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.

     
    Step 2 show running-config | include radius-server host


    Example:
    Router# show running-config | include radius-server host
     

    Displays all the RADIUS servers that are configured in the global configuration mode.

     
    Step 3 show aaa servers


    Example:
    Router# show aaa servers
     

    Displays information about the number of requests sent to and received from authentication, authorization, and accounting (AAA) servers.

     

    Configuration Examples for AAA-SERVER-MIB Set Operation

    RADIUS Server Configuration and Server Statistics Example

    The following sample output shows the RADIUS server configuration and server statistics before and after the set operation.

    Before the Set Operation

    Router# show running-config | include radius-server host
    ! The following line is for server 1.
    radius-server host 172.19.192.238 auth-port 2095 acct-port 2096 key cisco2
    ! The following line is for server 2.
    radius-server host 172.19.192.238 auth-port 1645 acct-port 1646

    Server Statistics

    Router# show aaa servers
    RADIUS: id 2, priority 1, host 172.19.192.238, auth-port 2095, acct-port 2096
    State: current UP, duration 25s, previous duration 0s
         Dead: total time 0s, count 7
    Authen: request 8, timeouts 8
         Response: unexpected 0, server error 0, incorrect 0, time 0ms
         Transaction: success 0, failure 2
    Author: request 0, timeouts 0
         Response: unexpected 0, server error 0, incorrect 0, time 0ms
         Transaction: success 0, failure 0
    Account: request 0, timeouts 0
         Response: unexpected 0, server error 0, incorrect 0, time 0ms
         Transaction: success 0, failure 0
    Elapsed time since counters last cleared: 5m
    RADIUS: id 3, priority 2, host 172.19.192.238, auth-port 1645, acct-port 1646
    State: current UP, duration 5s, previous duration 0s
         Dead: total time 0s, count 2
    Authen: request 8, timeouts 8
         Response: unexpected 0, server error 0, incorrect 0, time 0ms
         Transaction: success 0, failure 4
    Author: request 0, timeouts 0
         Response: unexpected 0, server error 0, incorrect 0, time 0ms
         Transaction: success 0, failure 0
    Account: request 0, timeouts 0
         Response: unexpected 0, server error 0, incorrect 0, time 0ms
         Transaction: success 0, failure 0
    Elapsed time since counters last cleared: 3m

    SNMP Get Operation to Check the Configuration and Statistics of the RADIUS Servers

    aaa-server5:/users/smetri> getmany 10.0.1.42 casConfigTable
    casAddress.2.2 = 172.19.192.238
    casAddress.2.3 = 172.19.192.238
    casAuthenPort.2.2 = 2095
    casAuthenPort.2.3 = 1645
    casAcctPort.2.2 = 2096
    casAcctPort.2.3 = 1646
    casKey.2.2 = 
    casKey.2.3 =
    ! The following line shows priority for server 1.
    casPriority.2.2 = 1
    ! The following line shows priority for server 2.
    casPriority.2.3 = 2
    casConfigRowStatus.2.2 = active(1)
    casConfigRowStatus.2.3 = active(1)
    aaa-server5:/users/smetri> 

    SNMP Set Operation

    The key of the existing RADIUS server is being changed. The index “1” is being used. That index acts as a wildcard for addition, deletion, or modification of any entries.

    Change the key for server 1:=>
    aaa-server5:/users/smetri>  setany -v2c 10.0.1.42 public casAddress.2.1 -a 172.19.192.238 casAuthenPort.2.1 -i 2095 casAcctPort.2.1 -i 2096 casKey.2.1 -o king 
    casAddress.2.1 = 172.19.192.238
    casAuthenPort.2.1 = 2095
    casAcctPort.2.1 = 2096
    casKey.2.1 = king
    aaa-server5:/users/smetri>

    After the Set Operation

    After the above SNMP set operation, the configurations on the router change. The following output shows the output after the set operation.

    Router# show running-config | include radius-server host
    radius-server host 172.19.192.238 auth-port 1645 acct-port 1646
    ! The following line shows a change in the key value to “king.”
    radius-server host 172.19.192.238 auth-port 2095 acct-port 2096 key king

    Router# show aaa servers
    RADIUS: id 3, priority 1, host 172.19.192.238, auth-port 1645, acct-port 1646
    State: current UP, duration 189s, previous duration 0s
         Dead: total time 0s, count 2
    Authen: request 8, timeouts 8
         Response: unexpected 0, server error 0, incorrect 0, time 0ms
         Transaction: success 0, failure 4
    Author: request 0, timeouts 0
         Response: unexpected 0, server error 0, incorrect 0, time 0ms
         Transaction: success 0, failure 0
    Account: request 0, timeouts 0
         Response: unexpected 0, server error 0, incorrect 0, time 0ms
         Transaction: success 0, failure 0
    Elapsed time since counters last cleared: 6m
     
    ! The following line shows a new server with new statistics.
    RADIUS: id 4, priority 2, host 172.19.192.238, auth-port 2095, acct-port 2096
    State: current UP, duration 209s, previous duration 0s
         Dead: total time 0s, count 7
    Authen: request 0, timeouts 0
         Response: unexpected 0, server error 0, incorrect 0, time 0ms
         Transaction: success 0, failure 0
    Author: request 0, timeouts 0
         Response: unexpected 0, server error 0, incorrect 0, time 0ms
         Transaction: success 0, failure 0
    Account: request 0, timeouts 0
         Response: unexpected 0, server error 0, incorrect 0, time 0ms

    Additional References

    The following sections provide references related to the AAA-SERVER-MIB Set Operation feature.

    Related Documents

    Related Topic

    Document Title

    Configuring SNMP

    Configuring SNMP Support in the Cisco IOS Network Management Configuration Guide

    Standards

    Standard

    Title

    No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.

    --

    MIBs

    MIB

    MIBs Link

    No new or modified MIBs are supported by this feature, and support for existing MIBs has not been modified by this feature.

    To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

    http:/​/​www.cisco.com/​go/​mibs

    RFCs

    RFC

    Title

    No new or modified RFCs are supported by this feature, and support for existing RFCs has not been modified by this feature.

    --

    Technical Assistance

    Description

    Link

    The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

    To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

    Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

    http:/​/​www.cisco.com/​cisco/​web/​support/​index.html

    Feature Information for AAA-SERVER-MIB Set Operation

    The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

    Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

    Table 1 Feature Information for AAA-SERVER-MIB Set Operation

    Feature Name

    Releases

    Feature Information

    AAA-SERVER-MIB Set Operation

    12.3(11)T

    12.4(4)T

    12.2(33)SRE

    The AAA-SERVER-MIB Set Operation feature allows the authentication, authorization, and accounting (AAA) server configuration to be extended or expanded by using the CISCO-AAA-SERVER-MIB to create and add new AAA servers, modify the “KEY” under the CISCO-AAA-SERVER-MIB, and delete the AAA server configuration.

    The following commands were introduced or modified: show aaa servers, show running-config, show running-config vrf.