Step 1 | enable
Example:
Device> enable
|
Enables
privileged EXEC mode.
|
Step 2 | configure terminal
Example:
Device# configure terminal
|
Enters global
configuration mode.
|
Step 3 | interface tunnel
number
Example:
Device(config)# interface tunnel 11
|
Specifies the
interface tunnel number and enters interface configuration mode.
|
Step 4 | ip address
ip-address
mask
Example:
Device(config-if)# 11.1.1.1 255.255.255.0
|
Configures the
IP address on the interface.
|
Step 5 | ip pim passive
Example:
Device(config-if)# ip pim passive
|
Enables IP PIM
passive mode operation.
|
Step 6 | ip igmp version
version
number
Example:
Device(config-if)# ip igmp version 3
|
Specifies IGMP
version.
|
Step 7 | ipv6 enable
Example:
Device(config-if)# ipv6 enable
|
Enables IPv6
on interface.
|
Step 8 | ipv6 pim passive
Example:
Device(config-if)# ipv6 pim passive
|
Enables IPv6
PIM passive mode operation.
|
Step 9 | tunnel source
interface-type
interface-number
Example:
Device(config-if)# tunnel source loopback 0
|
Configures
tunnel source as a loopback interface.
|
Step 10 | tunnel mode udp ip
Example:
Device(config-if)# tunnel mode udp ip
|
Specifies the
UDP encapsulation protocol.
|
Step 11 | tunnel destination dynamic
Example:
Device(config-if)# tunnel destination dynamic
|
Applies the
tunnel destination address dynamically to the tunnel interface.
|
Step 12 | tunnel dst-port dynamic
Example:
Device(config-if)# tunnel dst-port dynamic
|
Applies the
tunnel destination port dynamically.
|
Step 13 | tunnel src-port dynamic
Example:
Device(config-if)# tunnel src-port dynamic
|
Applies the
tunnel source port dynamically.
|
Step 14 | amt gateway traffic
{ip |
ipv6}
Example:
Device(config-if)# amt gateway traffic ipv6
|
Enables IPv4
or IPv6 traffic on AMT gateway interface.
|
Step 15 | amt gateway
relay-address
IP
address
Example:
Device(config-if)# amt gateway relay-address 172.16.0.0
|
Specifies
the destination IP address of AMT discovery.
|
Step 16 | exit
Example:
Device(config-if)# exit
|
Exits
interface configuration mode and returns to global configuration mode.
|
Step 17 | ip multicast-routing
distributed
Example:
Device(config)# ip multicast-routing distributed
|
Enables
Multicast Distributed Switching (MDS).
|
Step 18 | ipv6
multicast-routing
Example:
Device(config)# ipv6 multicast-routing
|
Enables
multicast routing using Protocol Independent Multicast (PIM) and Multicast
Listener Discovery (MLD).
|
Step 19 | ip pim ssm {default
|
range
access-list}
Example:
Device(config)# ip pim ssm default
|
Specifies
the Source Specific Multicast (SSM) range of IP multicast addresses.
|
Step 20 | ipv6 multicast
pim-passive-enable
Example:
Device(config)# ipv6 multicast pim-passive-enable
|
Enables
passive PIM operation.
|
Step 21 | ip route
ip-address
interface-type interface-number [multicast]
Example:
Device(config)# ip route 101.0.0.2 255.255.255.255 tunnel10 multicast
|
Specifies
the IP address along with interface type, interface number, and multicast
route.
|
Step 22 | ipv6 route
ipv6-prefix/prefix-length
interface-type interface-number
[multicast]
Example:
Device(config)# ipv6 route 2011::101:0:0:2/128 Tunnel10 multicast
|
Specifies
the IPv6 prefix and length along with interface type, interface number, and
multicast route (route only usable by multicast).
|