The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
This section describes open and resolved severity 1 and 2 caveats and select severity 3 caveats:
The “Open Caveats” sections list open caveats that apply to the current release and may apply to previous releases. A caveat that is open for a prior release and is still unresolved applies to all future releases until it is resolved.
The “Resolved Caveats” sections list caveats resolved in a specific release, but open in previous releases.
Cisco Bug Search Tool (BST), the online successor to Bug Toolkit, is designed to improve effectiveness in network risk management and device troubleshooting. You can search for bugs based on product, release, and keyword, and aggregates key data such as bug details, product, and version. For more details on the tool, see the help page located at http://www.cisco.com/web/applicat/cbsshelp/help.html .
W |
Description |
---|---|
Symptom: In a very rare occurrence, continuous tracebacks occur. The standby Supervisor card is continuously reset. the following traceback is observed: %COMMON_FIB-2-IF_NUMBER_ILLEGAL: STANDBY:Attempt to create CEF interface for Qam7/1.44 with illegal if_number: 0 Condition: This occurs when the max carriers are removed and set. The Supervisor card is configured with 1:1 line card redundancy and all channels in the line card are configured with Video and DEPI mode. Automated script configures supervisor max-carriers by setting & unsetting it continously using cable downstream max-carriers on range of QAM interfaces thru interface range qam. This behavior was never observed with manual operation with the above command. One of 20 attempts can get this scenerio with automated script. Repeat these steps atleast 16-17 times. 1. Config 192 powerkey encrypted channels, 143 remote depi channels in LC7 and config 1:1 LCRED (LC 7, LC12) 2. Remove max-carriers using the cmd interface range qam & no cable downstream max-carriers. 3. Set the Max-carriers using the command cable downstream max-carriers. 4. Tracebacks are thrown. Workaround: Active Supervisor card gets into inconsistent mode with standby Supervisor card and it can be recovered by resetting the chassis. Configure cable downstream max-carriers command in maintenance window. |
|
Symptom: Cisco RFGW10 with 9:1 DS384 line card redundancy configured, displays NO in output of “show cable video session all” command. Conditions: This occurs rarely when any line card switches over. Workaround: None since there is no service impact and this is a display problem. |
|
Symptom: The following memory allocation error message occurs on the Cisco RFGW-10 platform with DS384 line card. %SYS-2-MALLOCFAIL: Memory allocation of 756 bytes failed from 0x104BCF8C, alignment 8 Pool: I/O Free: 69328 Cause: Memory fragmentation Alternate Pool: None Free: 0 Cause: No Alternate pool -Process= "IF-MGR control process", ipl= 0, pid= 65 %RFGW-3-UNEXPECTED: DB tx failed with reason 6 for VSCM SESSION DB using non-blocking ipc; db sync = DYNAMIC_SYNC, db operation = DB_UPDATE, db key Conditions: This issue occurs when there is a image upgrade for Cisco RFGW-10 platform from earlier releases to IOS-XE Release 3.3.1SQ. Workaround: Wait for the chassis to recover automatically or reload the chassis again with old IOS image. |
|
Symptom: On a very rare occurrence, line card crashes with the following error message: %RFGW-3-LINECARD_FAILURE: Linecard in slot 3 is reporting a Fpga Major Failure (0x0001) %C4K_CHASSIS-2-LINECARDDS384MAJOREVENT: Slot 3, source 1 state 1 detects SH Watchdog Expired, sequence: 207 (0x9BCF206A) %RFGW-6-HEARTBEAT_WARNING: Heartbeat process has failed to receive heartbeats (for 3 consecutive seconds), for linecard 3 Conditions: This issue occurs during longevity and if Cisco RFGW-10 is idle for a long time. Workaround: Line card automatically recovers and no workaround is required. |
|
Symptoms: Cisco RFGW-10 platform running ten DS384 line crads (9:1 redundancy) with 40 Gbps DEPI traffic and 26K Video sessions might hit with below tracebacks vscm_source_get_fsm_state_by_obj -> Dst slot -1 in FSM doesn't match the input dst slot 12 Conditions: Multiple Line card Switchovers with SDV 90 channel changes per second and VOD 20 channel changes per second Workaround: None, since there is no service impact. |
|
Symptoms: The following error occurs: LC_ERRMSG_FAILOVER_TRIGGER Video Session Mutex lock not released" Conditions: This occurs in a rare instance, on a Cisco RFGW-10 platform running ten DS384 LC (9:1 line card redundancy) with 40 Gbps DEPI traffic and 27K Video sessions. This occurs when the chassis is in churn for a longer duration of SDV 90channel changes/sec and VOD 20 channel changes/sec, followed by series of linecard switchovers, followed by a series of linecard switchovers. Workaround: None. The linecard recovers automatically after rebooting. |
|
Symptom: The standby line card is reset and goes to RPR mode. Conditions: This occurs when the line card configured with video configurations, is removed, followed by a Stateful Switch Over (SSO). Workaround: Reload the chassis. |
|
Symptom: The video QAMs configured on some line cards are muted. Conditions: This occurs on a fully loaded chassis with 9:1 line card redundancy configured, and the IOS on the Cisco CMTS is upgraded from Cisco IOS-XE Release 3.3.0SQ to Cisco IOS-XE Release 3.4.1SQ. Workaround: Manually unmute the video QAMs. |
|
Symptom: Enforcement of Dual-Crypt algorithm using GUI fails. Conditions: This occurs when the GUI is used enforce the dual-crypt algorithm. The GUI does not have a dual-crypt button. The option is displayed as pkey csa. Workaround: Enforce dual-crypt using the CLI. |
|
Symptom: Cisco RFGW10 platform with 10 DS384 LC ( 9:1 LCRED) with 20K Video session with 400 SUP SSOs might hit below errors, configuration sync issue and Stby SUP would drop to RPR. %FILESYS-4-RCSF: Secondary running config write error (-1) <Error Sending Request> Oct 11 03:38:18.886 EDT: %ISSU-3-INCOMPATIBLE_PEER_UID: Setting image (rfgwk10-ENTSERVICESK9-M), version (03.04.00.SQ28) on peer uid (1) as incompatible Oct 11 03:38:18.886 EDT: Config Sync: Bulk-sync failure due to Servicing Incompatibility. Please check full list of mismatched commands via: show redundancy config-sync failures mcl Conditions: This occurs when the supervisor card undergoes several stateful switch overs (SSOs). Workaround: To recover the secondary supervisor card, reload the chassis. Services may not be impacted. |
|
Symptom: Cisco RFGW10 platform running 10 DS384 LC ( 9:1 LC RED) with 40 Gbps DEPI traffic and 27K Video sessions might hit the below error message with heartbeat failure %RFGW-3-HEARTBEAT_ALIVE: Heartbeat process has failed to receive the first heartbeat message (for 600 consecutive seconds), resetting linecard Conditions: This occurs in a very rare instance when chassis is in churn with SDV 90channel changes/sec and VOD 20 channel changes/sec, on performing multiple linecard switchovers. Workaround: Reset the linecard. |
|
Symptom: Cisco RFGW-10 platform having multicast uplink and generic PIM combination, may have multicast video sessions Input set to OFF. Conditions: This occurs when a series linecard and supervisor switchovers occur. Workaround: There is no workaround. This issue is seen when the multicast uplink only or Generic PIM with specific routes only, are used for multicast traffic. |
Caveat |
Description |
---|---|
Symptom: Timestamp column details is missing in Alarm and Summary pages. Conditions: None. Workaround: None. |
|
Symptom: QAMs assigned to an LQAM group are displayed even if the QAMs are not configured under that LQAM group. Conditions: This occurs in rare cases where LQAM groups have stale entries. Workaround: Use an LQAM group which is not already in use. Use the following commands: To delete particular stale LQAM group entries use the clear cable downstream slot lqam-group command. Or To delete a particular QAM entry in stale LQAM group entries use the clear cable downstream slot lqam-group carrier-id command. |
|
Symptom: DEPI down message is not displayed on the RFGW-10. The show cable depi-ctrl-sessions teardown detail command displays these details. Conditions: This is observed on the Cisco RFGW-10 platform. Workaround: This is expected behavior. The show cable depi-ctrl-sessions teardown detail command displays the details. There is no service impact. |
|
Symptom: Input voltage is lowered to near to shut off and TCC cards go off line for low power with out low power alarms *May 4 11:51:21.570: %C4K_CHASSIS-3-LINECARDSEEPROMREADFAILED: Failed to read module 13's serial eeprom, try reinserting module *May 4 11:51:21.580: %C4K_CHASSIS-3-LINECARDSEEPROMREADFAILED: Failed to read module 14's serial eeprom, try reinserting module Conditions: This occurs when the voltage input is lowered to approximately 38.0 Volts. Workaround: There is no workaround. |
|
Symptom: The RFGW-10 GigabitEthernet Spanning Tree Blocking port allows packets to pass through. In very rare instances, the blocked ports send SNMP and IGMP messages, while MAC flaps occur on the Cisco 2960 switch. Conditions: This occurs on Cisco RFGW-10 platforms connected to Cisco 2960 switch with redundant links from Supervisor slots (Tengigabit interface 1/1 and Tengigabit interface 2/1) running management traffic (SNMP or IGMP) and when the redundant links are shut using Spanning tree protocol (STP). Workaround: Reset the Supervisor card whose port is blocked by STP. |
|
Symptom: All modems connected to a Cisco RFGW-10 DS384 linecard go offline. The show tech command becomes unresponsive. The linecard logs show the same messages continuously repeating at the time the modems go offline. Conditions: This occurs on the Cisco RFGW-10 DS384 linecard on Cisco RFGW-10 chassis running the Cisco IOS-XE Release 3.2.2SQ. Workaround: A manual linecard rest or switchover and revertback may resolve the issue. |
|
Symptom: DCC Technique 4 fails when a modem is moved (downstream-only, no upstream move) from a group of four QAMs to another group of four or more QAMs on the same port of the Cisco RFGW-10 DS384 linecard. Conditions: This occurs on the Cisco RFGW-10 DS384 linecard. Workaround: Linecard failover and revertback or Removing the DEPI configuration of all the QAMs on the port and reconfiguring the QAMs again, may resolve the issue. |
|
Symptom: ceRedunEnableSwitchoverNotifs mib object is not set as true When '. Conditions: This occurs when snmp-server enable traps entity-red command is configured to generate the trap and the linecard switches over. Workaround: There is no workaround. |
|
Symptom: Notification OID for ceRedunEventSwitchover is 1.3.6.1.4.1.9.9.498 instead of the expected OID 1.3.6.1.4.1.9.9.498.0.1. Conditions: This occurs when the SNMP configuration is correct, NMS is in use, and a linecard switchover occurs. Workaround: The NMS software may be modified to shorten the OID. |
|
Symptom: Linecard crashes with the following message in the log: "ERROR, process bb_video launch too many times"
Conditions: This occurs in the rfgwk10-entservicesk9.03.03.01.SQ.150-2.SQB1.bin file. Workaround: There is no workaround. |
|
Symptom: DS384 LC reload due to unavailability of free ring buffers. Following error messages are noticed in logs - Jun 10 07:08:37.608 EDT: RFGW-6-HEARTBEAT_WARNING Heartbeat process has failed to receive heartbeats (for 3 consecutive seconds), for linecard 11 Jun 10 07:08:39.608 EDT: RFGW-3-HEARTBEAT_FATAL Heartbeat process has failed to receive heartbeats (for 5 consecutive seconds), resetting linecard 11 Jun 10 07:08:39.630 EDT: C4K_IOSMODPORTMAN-6-MODULEOFFLINE Module 11 is offline Jun 10 07:08:39.630 EDT: C4K_IOSMODPORTMAN-6-MODULEREMOVED Module 11 is removed Conditions: This occurs on Cisco RFGW-10 running rfgwk10-entservicesk9.03.03.01.SQ.150-2.SQB1 IOS release. Workaround: There is no workaround. |
|
Symptoms: The session count is not decremented and the bandwidth is not released from the deleted sessions. Conditions: This occurs when the ERMI qam-partition configured on the qam-channel is removed using the no cable partition command. Workaround: Remove the route to release the bandwidth. |
|
Symptom: “Uptime in current state” field in the show redundancy command output shows incorrect time after Supervisor card switchover on the Cisco RFGW-10. Conditions: This occurs on the supervisor card on Cisco RFGW-10 chassis. Workaround: There is no workaround. |
|
Symptom: RFGW-10 DS384 linecard crashes and recovers. Conditions: This occurs when the DEPI message handler thread gets a message from the configuration message queue, but the queue is empty (no IPC message is received in that queue). Workaround: There is no workaround. |
|
Symptom: The ONID/SDT ID is not removed from the port configuration. Conditions: This occurs when a standalone linecard is added to a linecard Redundancy (LCRED) group as secondary linecard. Workaround: The ONID/SDT ID is changed after removing the linecard from the LCRED group. |
|
Symptom: Standby SUP fails to boot because of Bulk Sync failure. Conditions: This occurs when a TSID is removed/Defaulted from ERMI QAM. Workaround: ERMI QAM Partition is removed from respective QAM on active supervisor and then we can load the standby supervisor. |
|
Symptom: The standby line card is reset and goes to RPR mode. Conditions: This occurs when the line card configured with DVB configurations, is removed, followed by a Stateful Switch Over (SSO). Workaround: Reload the chassis. |
|
Symptom: Video sessions are scrambled with duplicate TSID value. Conditions: This occurs when the same TSID is configured on two QAM channels (one with video mode local and another with video mode local encrypt) of same QAM port, then create video sessions on both the QAM channels, and overwrite the QAM mode as 'cable mode local encrypt' in a video mode local channel. The TSID is removed in the QAM configuration, but the video session will be scrambled with previous TSID. Workaround: Configure a unique TSID for that qam-channel. |
|
Symptom: The following tracebacks occur: *Aug 19 05:14:25.181 IST: rfgw_sdt_service_desc_show_rec -> ERROR: Unable to find SDT profile 22 *Aug 19 05:14:25.183 IST: -Traceback= 1#51562121bc405f90b02b90d81079d595 :10000000+12B6C4C :10000000+C4D800 :10000000+C4BB18 :10000000+C4DBF0 :10000000+C4E050 :10000000+1221624 :10000000+127EFA8 :10000000+1F325C0 :10000000+1F30138 :10000000+154AE34 :10000000+156385C *Aug 19 05:14:25.183 IST: rfgw_sdt_service_desc_show_rec -> ERROR: Unable to find SDT profile 22 Conditions: This occurs when the show cable video sdt profile, show cable video service descriptor id commands are executed. Workaround: No workaround, since there is no service impact. |
|
Symptom: Multicast Sessions are off while re-establishing. Conditions: This occurs when the primary link is in “Admin Down” state and the backup uplink is Active. Re-establishing the session after the cleared the session using “clear cable video session Qam” command. Workaround: There is no workaround. |
|
Symptom: Bulk synchronization failure occurs when the standby supervisor boot up and the ERMI QAM partition is not active but the partition is associated to the QAM interface. Condition: Bulk synchronization failure occurs when the “cable partition <qp-id>” command is synchronized to standby card that is under QAM sub-interface configuration. Workaround: Activate ERMI QAM partition by using “active” command under cable partition, then boot up the standby supervisor. |
|
Symptom: Multicast sessions turn off. Conditions: This occurs after linecard switchover (LCSO) and the primary uplink down. Workaround: There is no workaround. |
|
Symptom: The rf-power value is not synchronized with some QAM channels in standby supervisor card. Conditions: This occurs while changing the max-carrier value with QAM configurations in the linecard Workaround: Copy the configuration to the start-up configuration and statefully switchover (SSO) the chassis. |
Caveat |
Description |
---|---|
Symptoms: The following error messages are seen in supervisor console during churn: LC_ERRMSG_IPC_MALLOC_BUFFER_FAILED VIDEO-EVT LC_ERRMSG_IPC_MALLOC_BUFFER_FAILED VIDEO SERVICE_CHANGE LC_ERRMSG_IPC_MALLOC_BUFFER_FAILED VIDEO SCG_PROV
Conditions: This issue occurs in a rare instance. The error message pops up after about 48 hours of the SDV and VOD churn. Workaround: There is no impact and the Cisco RFGW-10 recovers automatically if a redundant line card is configured. |
|
Symptoms: The show cable video session all command displays both MPTS Remap and MPTS Passthru sessions as ACTIVE, and the following error occurs: LC_ERRMSG_VIDEO_PROG_NUM_IN_USE Conditions: This issue occurs when a program number conflict exists between a MPTS Passthru session and MPTS remap session of QAM Channel in the LC. Workaround: Reconfigure the MPTS Remap session with unique program number such that there is no program number conflict with the MPTS Passthru. |
|
Symptom: The downstream license consumed count is not updated after upgrading the local video sessions. Conditions: This issue occurs when the DS license is downgraded and upgraded after enabling 192 local video sessions (tier-based). Workaround: Reset the Cisco RFGW-10 DS-384 line card. |
|
Symptoms: CA descriptor, bound with ES descriptors, is missing in PMT table of a program in QAM output. Conditions: This issue occurs when the incoming PMT is modified changing the stream type of a PID to a different stream type, the CA descriptor associated is lost. Workaround: There is no workaround. |
|
Symptoms: The following error message is seen during supervisor switchover: LC_ERRMSG_VIDEO_PSI_CRC_ERROR PMT: Conditions: This issue is observed during the supervisor switchover when standby supervisor is initializing as active. Workaround: There is no workaround. |
|
Symptoms: Some of the QRG is not removed in Standby Supervisor, in the console view. Conditions: This issue occurs when QRG is removed using GUI. Workaround: Do not verify the QRG in the console while deleting it using the GUI. |
Caveat |
Description |
---|---|
Symptom: Certain SSH version 2 packets may cause a memory leak on a Cisco IOS device configured for SSH. Authentication is needed in order to exploit this vulnerability. Conditions: This issue is observed on a Cisco IOS device configured for SSH version 2 after it has received malformed SSHv2 packets. Successful, exploitation may cause system degradation or a partial denial of service condition on an affected device. Workaround: Disable SSH version 2. |
|
Symptom: The following error is observed, on boot with redundant supervisors leading to ISSU/SSO negotiation failure: "%NTP: unreasonable value" Conditions: This issue occurs when NTP and Redundant supervisor card are configured and the NTP clock values drift above acceptable values constantly. Workaround: Remove the ntp clock-period configuration using no ntp clock-period command. Disable config-sync check for Stateful Switch-over (SSO). |
|
Symptom: The following UPX NACK error message occurs after 124 replicant groups configured on a port: %RFGW-3-LINECARD_ERRMSG_ERR: SLOT 3:BB_ERRMSG_DS_PHY_UPX_ERR:wr cmd NACK for seq_num=0xa92,addr=0x212003e0,cmddata=0xc803f07f.b7500139.000005e8.00000650 556e6d61.74636820.62657477.65656e20 34204455.43204368.69707300.00000000 00000000.00000000.00000000.00000000, 00000000.00000feb.00000000.00000000 00000000.00000000.00000000.00000000 00000000.00000000.00000000.00000000 00000000.00000000.00000000.00000000, err_code=34 Conditions: Cisco RFGW-10 is configured with RF Spanning. Port1 and port2 are configured for pilot channels with more than 124 replicate groups combined. Port3 is configured with these replicate groups from both the ports ie, port3 channels are replicates from port1 and port2 respectively in a way that port3 channels form more than 32 routing groups (each routing group supports 4 channels). Each replicate has less than 4 channels in port3 which allows more than 32 routing groups. Workaround: Do not configure a port with replicates to form more than 32 routing lqam groups. This is not recommended and supported. Currently there is no workaround. |
|
Symptoms: Invalid frequencies error messages for 8 MHz Annex A QAMs are observed. Conditions: This issue occurs when configuring frequencies with 8MHz overlap in Annex-A. Workaround: There is no workaround. |
|
Symptoms: Bulk synchronization fails. PRC errors are seen on active Supervisor card and the standby Supervisor card resets before going into RPR mode. The PRC error is as follows: Config Sync: Bulk-sync failure due to Servicing Incompatibility. Please check full list of mismatched commands via: show redundancy config-sync failures mcl interface Qam9/1.1 ! <submode> "subinterface" - cable downstream interleaver-depth I128-J1 ! </submode> "subinterface" interface Qam9/1.2 ! <submode> "subinterface" - cable downstream interleaver-depth I128-J1 Conditions: This issue occurs when the rf-profile is changed from Annex-B to Annex-A and the Supervisor card is switched over. Workaround: Reset the standby Supervisor card after trying to change the rf-profile. |
|
Symptom: The following error message is observed on Cisco RFGW-10: %RFGW-3-LINECARD_ERRMSG_ERR: SLOT 5:LC_ERRMSG_VIDEO_PROG_NUM_IN_USE ADD_SES: OUT 195, QAM 130, prog 50777 Conditions: This issue occurs when there is multiple Supervisor card switchover along with continuous churn. Workaround: There is no workaround required. |
|
Symptom: In a Annex-A high frequency profile configured port with 96 channels, upper channels from 93 to 96 will not be operational. Conditions: This issue occurs when the port is configured with maximum carriers set to 96 and configured with Annex A high frequency profile. Workaround: There is no workaround. |
|
Symptom: The following tracebacks and error messages are observed on Cisco RFGW-10 with 9:1 DS384 line card redundancy chassis with video SDV and VOD churn. vscm_source_get_fsm_state_by_obj -> Dst slot -1 in FSM doesn't match the input dst slot 12 <Active console> vscm_session_delete_db -> Unable to remove session 673059849 from carrier_id table <Active console> vscm_session_delete_db -> Unable to delete session 673059849 from database. Error code = 115 <Active console> vscm_map_chkpt_delete -> Unable to locate map 13725 from database <Stby console> vscm_source_db_chkp_decode_for_session -> Map id 6217 received from chkpt message not same as map id 3324 in existing source [176.1.1.1:0, 238.2.1.153:1] in db <Flooding stby console> vscm_map_chkpt_active_source_indx -> Unable to locate map 4385 for active_source_indx set <Flooding stby console> Conditions: This error occurs after performing multiple line card switchover. Workaround: There is no workaround required. |
|
Symptom: Traceback with error message is observed during bootup. %RFGW_CSL-1-LIC_DB_GET_REC_FAIL: Slot:4 license DB record doesn't exist! Retry after bootup %RFGW_CSL-1-NULL_LICENSE_INFO: LC slot:4 license info is NULL! Conditions: This issue occurs during booutp and line card reset. Workaround: The chassis recovers automatically and no workaround is required. |
|
Symptom: The show power command output does not show any input voltage, or show utilization on a per supply basis. Conditions: This issue occurs when the show power command is used. Workaround: There is no known workaround. |
|
Symptoms: There is no prompt for confirmation to delete the video sessions. resulting in deletion of video sessions without any notification. Conditions: This issue occurs when changing the TSID using GUI. Workaround: There is no workaround. |
|
Symptom: Standby and active Supervisor cards crash. Conditions: This issue occurs when older Small Form-factor Pluggable (SFP) transceivers are used on the Cisco RFGW 10 DS384 line card and the service unsupported-transceiver command is used. Workaround: Disable the unsupported transceivers using no service unsupported-transceiver command OR Remove the SFPs before removing the Cisco RFGW 10 DS384 line card and reinsert the SFPs after the Cisco RFGW 10 DS384 line card is reinserted. |
|
Symptoms: LC crashed and stuck in init state. %C4K_CHASSIS-2-LINECARDDS384MAJOREVENT: Slot 10, source 1 state 1 detects P4080 Soft Failure, sequence: 109 (0x826D3800) Conditions: This issue occurs while booting up or after series of line card switch overs Workaround: There is no workaround. |
|
Symptoms: BB_SCs crash occurs on a large-scale test bed with 10 DS-384 line cards with 26,000 video sessions created using SDV (VSRM) and VOD. Conditions: This issue occurs when multiple line cards switch over. Workaround: The line card recovers automatically. |
|
Symptom: ACTIVE supervisor fails and switches over. Conditions: This issue occurs when the show cable video session id command is executed. Workaround: There is no workaround. |
|
Symptom: The line card crashes with errors and tracebacks. The DEPI and Video traffic is not recovered even after the line cards are operational. Conditions: This issue occurs when DEPI and Video traffic on same line card and line card is switched over. Workaround: There is no workaround. |
|
Symptoms: Warning with internal URL is displayed on IOS-XE boot on production build. Conditions: Bootparam variable is not set (ex: disableautoreboot). Workaround: There is no workaround. |
|
Symptoms: Supervisor card does not automatically reboot during a crash and the following message is observed: disableautoreboot set, switch won't reboot Conditions: This issue occurs when the following rommon variables are set during the initial bootup: BootParam1/2/3/4=ip=::::nova:eth0:off rw disableautoreboot" BootMode=0 is set as environment variable. Workaround: Power cycle the box. Unset BootParam1/2/3/4 and BootMode in rommon mode using the following commands: unset BootParam1/2/3/4 unset BootMode |
|
Symptoms: ERMI sessions lost and QAM bandwidth full problem occurs. Conditions: This issue occurs when the Supervisor card switches over with ERMI SDV churn. Workaround: There is no workaround. |
|
Symptoms: Unable to remove the cable video route configured, it is rejected with an error message: %ERROR: Routes is being used. Please remove individual routes remove sessions prior deleting the load balancing group Conditions: Clear all video session configured in LC and remove cable video route configured. Workaround: Remove configured routes one by one under load-balancing-group. |
|
Symptoms: DS48 linecard does not display rf-parameter and frequency output. Conditions: This issue occurs when trying to verify the parameters of the qam controller of Cisco DS48 line card using show controller Qam-red slot/port.channel downstream. Workaround: There is no workaround. |
|
Symptom: License page must be modified to reflect the CLI output. Conditions: None. Workaround: There is no workaround. |