Cisco Wide Area Applications Services Command Reference Guide 5.3.1
AppNav Controller Group Configuration Mode Commands
Downloads: This chapterpdf (PDF - 54.0KB) The complete bookPDF (PDF - 8.77MB) | Feedback

AppNav Controller Group Configuration Mode Commands

Table Of Contents

AppNav Controller Group Configuration Mode Commands

(config-scg) appnav-controller

(config-scg) description


AppNav Controller Group Configuration Mode Commands


To configure an AppNav Controller group (ANCG) that is part of an AppNav Cluster, use the service-insertion appnav-controller-group global configuration command. To unconfigure settings, use the no form of this command.

service-insertion appnav-controller-group ancgroupname{description description | appnav-controller ip-address [description description]}

no service-insertion appnav-controller-group ancgroupname {description description | appnav-controller ip-address [description description]}

Syntax Description

ancgroupname

Specifies the name of an ANCG to configure and enters AppNav Controller group configuration mode to configure ANCG settings. If the ANCG does not exist, this command creates it.

description description

(Optional) Specifies a description of the ANCG with up to 200 alphanumeric and space characters.

appnav-controller ip-address

Specifies the IP address of an ANC to be added to the ANCG. The address must be the IP address of the interface on which the ANC communicates with other devices in the cluster.

description description

(Optional) Specifies a description of the ANC with up to 200 alphanumeric and space characters.


Defaults

No default behavior or values.

Command Modes

global configuration

Device Modes

appnav-controller

Usage Guidelines

Use the service-insertion appnav-controller-group command to configure an ANCG that is part of a AppNav Cluster. This command initiates the AppNav Controller group configuration mode, which is indicated by a different prompt (config-scg). To return to global configuration mode, enter the exit command.

Each ANC in the AppNav Cluster must be configured with the settings for each ANCG in the cluster by using the service-insertion appnav-controller-group command.

An ANCG can contain a maximum of eight ANCs.

Examples

The following example shows how to configure and enable an ANCG with two ANC members, on an ANC:

ANC(config)# service-insertion appnav-controller-group myControllerGroup
ANC(config-scg)# description AppNav Controller group
ANC(config-scg)# appnav-controller 10.10.8.15 description Primary controller
ANC(config-scg)# appnav-controller 10.10.8.16 description Secondary controller
 
   

Related Commands

(config-scg) appnav-controller

(config-scg) description

(config) service-insertion

show service-insertion

(config-scg) appnav-controller

To configure the IP address and description of an ANC to be added to the ANCG, use the appnav-controller AppNav Controller group configuration command. To unconfigure the IP address or description, use the no form of this command.

appnav-controller ip-address [description description]

no appnav-controller ip-address [description description]

Syntax Description

ip-address

Specifies the IP address of an ANC to be added to the ANCG. The address must be the IP address of the interface on which the ANC communicates with other devices in the cluster.

description description

(Optional) Specifies a description of the ANC with up to 200 alphanumeric and space characters.


Defaults

No default behavior or values.

Command Modes

AppNav Controller group configuration

Device Modes

appnav-controller

Usage Guidelines

An ANCG can contain a maximum of eight ANCs.

Examples

The following example shows how to configure the IP addresses of two ANCs in an ANCG:

ANC(config)# service-insertion appnav-controller-group myControllerGroup
ANC(config-scg)# appnav-controller 10.10.8.15 description Primary controller
ANC(config-scg)# appnav-controller 10.10.8.16 description Secondary controller
 
   

Related Commands

(config-scg) description

(config) service-insertion

show service-insertion

(config-scg) description

To configure the ANC description, use the description AppNav Controller group configuration command. To unconfigure the description, use the no form of this command.

description description

no description description

Syntax Description

description

Specifies a description of the ANC with up to 200 alphanumeric and space characters.


Defaults

No default behavior or values.

Command Modes

AppNav Controller group configuration

Device Modes

appnav-controller

Examples

The following example shows how to configure an ANC description:

ANC(config)# service-insertion appnav-controller-group myControllerGroup
ANC(config-scg)# description AppNav Controller group
 
   

Related Commands

(config-scg) appnav-controller

(config) service-insertion

show service-insertion