Cisco Wide Area Application Services Command Reference (Software Version 4.1.3)
Cisco WAAS Software Command Summary
Downloads: This chapterpdf (PDF - 416.0KB) The complete bookPDF (PDF - 7.09MB) | Feedback

Cisco WAAS Software Command Summary

Table Of Contents

Cisco WAAS Software Command Summary


Cisco WAAS Software Command Summary


This chapter summarizes the Cisco WAAS 4.1.1 software commands.

Table 2-1 lists the WAAS commands (alphabetically) and indicates the command mode for each command. The commands used to access configuration modes are marked with an asterisk. Commands that do not indicate a particular mode are EXEC mode commands. The same command may have different effects when entered in a different command mode, so they are listed and documented separately. (See Chapter 1, "Using the WAAS Command-Line Interface" for a discussion about using CLI command modes.)

In Table 2-1, in the Device Mode column "All" indicates that the particular CLI command is supported in both central-manager mode and application-accelerator mode.

Table 2-1 Command Summary 

Command
Description
CLI Mode
Device Mode

(config) aaa accounting

Configures AAA accounting.

global configuration

All

(config) accelerator cifs

Enables the CIFS application accelerator.

global configuration

application-accelerator

(config) accelerator cifs preposition

Configures a CIFS application accelerator preposition directive.

global configuration

application-accelerator

(config) accelerator epm

Enables the EPM application accelerator.

global configuration

application-accelerator

(config) accelerator http

Enables the HTTP application accelerator.

global configuration

application-accelerator

(config) accelerator mapi

Enables the MAPI application accelerator.

global configuration

application-accelerator

(config) accelerator nfs

Enables the NFS application accelerator.

global configuration

application-accelerator

(config) accelerator ssl

Enables the SSL application accelerator.

global configuration

application-accelerator

(config) accelerator video

Enables the video application accelerator.

global configuration

application-accelerator

(config) accelerator windows-print

Enables the Windows print accelerator

global configuration

application-accelerator

(config) alarm overload-detect

Configures the detection of an alarm overload.

global configuration

All

(config) asset

Configures the tag name for the asset tag string.

global configuration

All

(config) authentication configuration

Configures administrative authentication and authorization parameters.

global configuration

All

(config) authentication content-request

Configures request for content authentication and authorization parameters.

global configuration

All

(config) authentication fail-over

Configures authentication failover if the primary authentication server is unreachable.

global configuration

All

(config) authentication login

Configures administrative login authentication and authorization parameters.

global configuration

All

(config) authentication strict-password-policy

Configures strong password policy parameters.

global configuration

All

(config) auto-discovery

Discovers origin servers that cannot receive TCP packets with options and adds the IP addresses to a blacklist for a specified number of minutes.

global configuration

application-accelerator

(config) auto-register

Enables the discovery of a primary interface on a WAE and its automatic registration with the WAAS Central Manager through DHCP.

global configuration

application-accelerator

(config-if) autosense

Sets the current interface to autosense.

interface configuration

All

(config-vb) autostart

Sets a virtual blade to automatically start when the WAE is started.

virtual blade configuration

application-accelerator

(config-if) bandwidth

Sets the specified interface bandwidth to 10, 100, or 1000 Mbps.

interface configuration

All

(config) banner

Configures message-of-the-day, login, login and EXEC banners.

global configuration

All

(config-vb) boot

Configures the boot image location and source for a virtual blade.

virtual blade configuration

application-accelerator

(config) bypass

Configures the bypass functions on a WAE.

global configuration

application-accelerator

(config-ca) ca-certificate

Sets the certification authority file.

certification authority configuration

All

cd

Changes the directory.

user-level EXEC and privileged-level EXEC

All

(config) cdp

Enables the Cisco Discovery Protocol (CDP) for the WAAS device.

global configuration

All

(config-if) cdp

Enables CDP on an interface.

interface configuration

All

(config) central-manager

In application-accelerator mode, used to specify the IP address of the WAAS Central Manager with which the WAE needs to register. In central-manager mode, used to specify the WAAS Central Manager's role and GUI port number.

global configuration

All

cifs

Controls CIFS adapter operations and run-time configurations.

user-level EXEC and privileged-level EXEC

application-accelerator

(config-cipher-list) cipher

Configures a cipher suite on the cipher list.

cipher list configuration

All

clear arp-cache

Resets the ARP cache.

privileged-level EXEC

All

clear cache

Resets the cached objects.

privileged-level EXEC

All

clear cdp

Resets Cisco Discovery Protocol statistics.

privileged-level EXEC

All

clear ip

Resets IP access list statistics.

privileged-level EXEC

All

clear license

Resets licensing configuration.

privileged-level EXEC

All

clear logging

Resets the syslog messages saved in a disk file.

privileged-level EXEC

All

clear statistics

Resets statistics data.

privileged-level EXEC

All

clear statistics accelerator

Resets all global statistics.

privileged-level EXEC

All

clear statistics connection

Resets connection statistics.

privileged-level EXEC

All

clear transaction-log

Archives the working transaction log file.

privileged-level EXEC

All

clear users

Resets user connections or unlocks users that have been locked out.

privileged-level EXEC

All

clear windows-domain-log

Clears user connections and unlocks users that have been locked out.

privileged-level EXEC

All

clock

Manages the system clock.

privileged-level EXEC

All

(config) clock

Sets the summer daylight saving time of day and time zone.

global configuration

All

cms

Configures the parameters for the Centralized Management System (CMS) embedded database.

privileged-level EXEC

All

cms secure-store

Configures secure store encryption

privileged-level EXEC

All

(config) cms

Schedules the maintenance and enables the Centralized Management System on a specific WAAS device.

global configuration

All

configure*

Enters configuration mode from privileged EXEC mode.

privileged-level EXEC

All

copy cdrom

Copies files from a CD-ROM.

privileged-level EXEC

All

copy cdrom wow-recovery

Recovers Windows on a virtual blade without reloading the software.

privileged-level EXEC

All

copy compactflash

Copies files from the Compact Flash card.

privileged-level EXEC

All

copy disk

Copies configuration information or files from a disk.

privileged-level EXEC

All

copy ftp

Copies files from an FTP server.

privileged-level EXEC

All

copy http

Copies files from an HTTP server.

privileged-level EXEC

All

copy running-config

Copies information from the current system configuration.

privileged-level EXEC

All

copy startup-config

Copies information from the startup configuration.

privileged-level EXEC

All

copy sysreport

Copies system troubleshooting information.

privileged-level EXEC

All

copy system-status

Copies the system status for debugging reference.

privileged-level EXEC

All

copy tech-support

Copies system information for technical support.

privileged-level EXEC

All

copy tftp

Copies the software image from the TFTP server.

privileged-level EXEC

All

copy virtual-blade

Copies software configuration or image data from a virtual blade disk image to an FTP server.

privileged-level EXEC

All

cpfile

Copies a file to the current directory.

privileged-level EXEC

All

(config-preposition) credentials

Sets the username and password credentials.

preposition configuration

application-accelerator

crypto delete

Removes SSL certificate and key files.

privileged-level EXEC

application-accelerator

crypto export

Exports SSL certificate and key files.

privileged-level EXEC

application-accelerator

crypto generate

Generates a self-signed certificate or a certificate signing request.

privileged-level EXEC

All

crypto import

Imports SSL certificate and key files.

privileged-level EXEC

application-accelerator

crypto pki

Initializes the PKI managed store.

privileged-level EXEC

All

(config) crypto pki

Configures public key infrastructure (PKI) encryption parameters.

global configuration

All

(config) crypto ssl

Configures secure sockets layer (SSL) encryption parameters.

global configuration

All

debug aaa accounting

Configures AAA accounting debugging.

privileged-level EXEC

All

debug accelerator

Configures accelerator debugging.

privileged-level EXEC

All

debug all

Configures all debugging.

privileged-level EXEC

All

debug authentication

Configures authentication debugging.

privileged-level EXEC

All

debug buf

Configures buffer manager debugging.

privileged-level EXEC

All

debug cdp

Configures CDP debugging.

privileged-level EXEC

All

debug cli

Configures CLI debugging.

privileged-level EXEC

All

debug cms

Configures CMS debugging.

privileged-level EXEC

All

debug dataserver

Configures data server debugging.

privileged-level EXEC

All

debug dhcp

Configures DHCP debugging.

privileged-level EXEC

All

debug dre

Configures DRE debugging.

privileged-level EXEC

application-accelerator

debug egress-method

Configures egress method debugging.

privileged-level EXEC

application-accelerator

debug emdb

Configures embedded database debugging.

privileged-level EXEC

All

debug epm

Configures DCE-RPC EPM debugging.

privileged-level EXEC

application-accelerator

debug flow

Configures network traffic flow debugging.

privileged-level EXEC

All

debug generic-gre

Configures generic GRE egress method debugging.

privileged-level EXEC

All

debug key-manager

Configures Central Manager key manager debugging.

privileged-level EXEC

All

debug logging

Configures logging debugging.

privileged-level EXEC

All

debug ntp

Configures NTP debugging.

privileged-level EXEC

All

debug print-spooler

Configures print spooler debugging.

privileged-level EXEC

application-accelerator

debug rbcp

Configures RBCP debugging.

privileged-level EXEC

All

debug rpc

Configures record remote procedure calls debugging.

privileged-level EXEC

All

debug snmp

Configures SNMP debugging.

privileged-level EXEC

All

debug stats

Configures statistics debugging.

privileged-level EXEC

All

debug tfo

Configures TFO flow optimization debugging.

privileged-level EXEC

application-accelerator

debug translog

Configures transaction logging debugging.

privileged-level EXEC

All

debug wafs

Sets the log level of WAFS running components.

privileged-level EXEC

application-accelerator

debug wccp

Configures WCCP information debugging.

privileged-level EXEC

application-accelerator

(config-std-nacl) delete

Deletes a line from the standard ACL.

standard ACL configuration

All

(config-ext-nacl) delete

Deletes a line from the extended ACL.

extended ACL configuration

All

delfile

Deletes a file.

privileged-level EXEC

All

deltree

Deletes a directory and its subdirectories.

privileged-level EXEC

All

(config-std-nacl) deny

Adds a line to a standard access list that specifies the type of packets that you want the WAAS device to drop.

standard ACL configuration

All

(config-ext-nacl) deny

Adds a line to an extended access-list that specifies the type of packets that you want the WAAS device to drop.

extended ACL configuration

All

(config-ca) description

Configures a description for the certification authority.

certification authority configuration

All

(config-vb) description

Configures a description for a virtual blade on your WAE.

virtual blade configuration

application-accelerator

(config-vb) device

Configures the device emulation parameters used by the virtual blade on your WAE.

virtual blade configuration

application-accelerator

(config) device mode

Specifies the device mode of the WAAS device.

global configuration

All

dir

Displays the files in a long list format.

user-level EXEC and privileged-level EXEC

All

(config) directed-mode

Configures the mode by which traffic is sent between two WAEs.

global configuration

application-accelerator

disable

Turns off the privileged EXEC commands.

privileged-level EXEC

All

disk

Configures the disks on the WAAS device.

privileged-level EXEC

All

(config-vb) disk

Configures disk space for a virtual blade on the WAE hard drive.

virtual blade configuration

application-accelerator

(config) disk disk-name

Disables a RAID-1 disk for online removal.

global configuration

All

(config) disk encrypt

Enables disk encryption.

global configuration

application-accelerator

(config) disk error-handling

Configures how the disk errors should be handled.

global configuration

All

(config) disk logical shutdown

Shuts down the RAID-5 logical disk drive.

global configuration

All

dnslookup

Resolves a DNS hostname.

user-level EXEC and privileged-level EXEC

All

(config-preposition) dscp

Setshe DSCP marking value for a preposition task.

preposition configuration

application-accelerator

(config-preposition) duration

Sets the maximum duration for a preposition task.

preposition configuration

application-accelerator

(config) egress-method

Configures the egress method for intercepted connections.

global configuration

application-accelerator

enable*

Accesses the privileged EXEC commands.

user-level EXEC

All

(config-preposition) enable

Enables or disables a preposition directive.

preposition configuration

application-accelerator

(config-if) encapsulation dot1Q

Sets the VLAN ID of traffic leaving the Cisco WAE Inline Network Adapter interface.

interface configuration

application-accelerator

(config) end

Exits configuration and privileged EXEC modes.

global configuration

All

(config) exec-timeout

Configures the length of time that an inactive Telnet or SSH session remains open.

global configuration

All

exit

Exits from privileged EXEC mode.

privileged-level EXEC

All

(config) exit

Exits from global configuration mode.

global configuration

All

(config-if) exit

Exits from interface configuration mode.

interface configuration

All

(config-std-nacl) exit

Exits from standard ACL configuration mode.

standard ACL configuration

All

(config-ext-nacl) exit

Exits from extended ACL configuration mode.

extended ACL configuration

All

(config-if) failover timeout

Configures the maximum time for the inline interface to transition traffic to another port after a failure event.

interface configuration

All

find-pattern

Searches for a particular pattern in a file.

privileged-level EXEC

All

(config) flow monitor

Configures network traffic flow monitoring.

global configuration

application-accelerator

(config-if) full-duplex

Sets the current interface to the full-duplex mode.

interface configuration

All

(config-if) half-duplex

Sets the current interface to half-duplex mode.

interface configuration

All

help

Provides assistance for the WAAS command-line interface in EXEC mode.

user-level EXEC and privileged-level EXEC

All

(config) help

Provides assistance for the WAAS command-line interface.

global configuration

All

(config) hostname

Configures the hostname of the WAAS device in global configuration mode.

global configuration

All

(config-preposition) ignore-hidden-dir

Configures to ignore hidden directories in the set of files to be prepositioned.

preposition configuration

application-accelerator

(config) inetd

Enables FTP, RCP, and TFTP services.

global configuration

All

(config-if) inline

Configures inline interception for an inlineGroup interface.

interface configuration

All

(config) inline vlan-id-connection-check

Enables VLAN ID checking on intercepted traffic.

global configuration

All

install

Installs a new image into Flash memory.

privileged-level EXEC

All

(config-vb) interface

Bridges a virtual blade interface to an interface on your WAE.

virtual blade configuration

application-accelerator

(config) interface GigabitEthernet*

Configures a Gigabit Ethernet interface. Provides access to interface configuration mode.

global configuration

All

(config) interface InlineGroup*

Configures a Inline Group channel, or standby interface. Provides access to interface configuration mode.

global configuration

All

(config) interface PortChannel*

Configures a port channel interface. Provides access to interface configuration mode.

global configuration

All

(config) interface standby*

Configures a standby interface. Provides access to interface configuration mode.

global configuration

All

(config) ip

Configures the initial network device configuration settings (for example, the IP address of the default gateway) on a WAAS device.

global configuration

All

(config-if) ip

Configures the IP address, subnet mask, or DHCP IP address negotiation on the interface of the WAAS device or Cisco WAE Inline Network Adapter.

interface configuration

All

(config-if) ip access-group

Controls the connections on a specific interface by applying a predefined access list.

interface configuration

All

(config) ip access-list*

Creates and modifies the access lists for controlling access to interfaces or applications. Provides access to ACL configuration mode.

global configuration

All

(config) kerberos

Configures user authentication against a Kerberos database.

global configuration

All

(config) kernel kdb

Enables the kernel debugger configuration mode.

global configuration

All

(config) kernel kdump

Enables the kernel crash dump mechanism.

global configuration

All

less

Displays the contents of a file using the LESS application.

user-level EXEC and privileged-level EXEC

All

license add

Adds a software license.

privileged-level EXEC

All

(config) line

Specifies the terminal line settings.

global configuration

All

(config-std-nacl) list

Displays a list of specified entries within the standard ACL

standard ACL configuration

All

(config-ext-nacl) list

Displays a list of specified entries within the extended ACL

extended ACL configuration

All

lls

Displays the files in a long list format.

user-level EXEC and privileged-level EXEC

All

(config) logging console

Configures system logging (syslog) to the console.

global configuration

All

(config) logging disk

Configures system logging (syslog) to a disk file.

global configuration

All

(config) logging facility

Sets the facility parameter for system logging (syslog).

global configuration

All

(config) logging host

Configures system logging (syslog) to a remote host.

global configuration

All

ls

Lists the files and subdirectories in a directory.

user-level EXEC and privileged-level EXEC

All

(config-preposition) max-cache

Sets the maximum cache percentage that prepositioned files can use.

preposition configuration

application-accelerator

(config-preposition) max-file-size

Sets the maximum size of a prepositioned file.

preposition configuration

application-accelerator

(config-vb) memory

Configures memory for a virtual blade from the WAE system.

virtual blade configuration

application-accelerator

(config-preposition) min-file-size

Sets the minimum size of a prepositioned file.

preposition configuration

application-accelerator

mkdir

Makes a directory.

privileged-level EXEC

All

mkfile

Makes a file (for testing).

privileged-level EXEC

All

(config-std-nacl) move

Moves a line to a new position within the standard ACL

standard ACL configuration

All

(config-ext-nacl) move

Moves a line to a new position within the extended ACL

extended ACL configuration

All

(config-if) mtu

Sets the interface Maximum Transmission Unit (MTU) packet size.

interface configuration

All

(config-preposition) name

Sets the name of a preposition directive.

preposition configuration

application-accelerator

(config) ntp

Configures the NTP server.

global configuration

All

ntpdate

Sets the NTP server name.

privileged-level EXEC

All

(config-pki-global-settings) ocsp

Configures the URL to be used as the global settings for the Online Certificate Status Protocol (OCSP) protocol revocation status checking.

PKI global-settings configuration

All

(config-preposition) pattern

Sets a file filter for a preposition directive.

preposition configuration

application-accelerator

(config-std-nacl) permit

Adds a line to a standard access list that specifies the type of packets that you want the WAAS device to permit for further processing.

standard ACL configuration

All

(config-ext-nacl) permit

Adds a line to an extended access list that specifies the type of packets that you want the WAAS device to permit for further processing.

extended ACL configuration

All

ping

Sends the echo packets.

user-level EXEC and privileged-level EXEC

All

(config) policy-engine application classifier

Defines a WAE's application policy and assigns the policy a name, a classifier, and a policy map.

global configuration

application-accelerator

(config) policy-engine application map adaptor EPM

Configures a WAE's application policy with advanced policy map lists of the EndPoint Mapper (EPM) service.

global configuration

application-accelerator

(config) policy-engine application map adaptor WAFS transport

Configures a WAE's application policies with the WAFS transport option.

global configuration

application-accelerator

(config) policy-engine application map basic

Deletes a specific basic (static) application policy map from the WAE's list of application policy maps.

global configuration

application-accelerator

(config) policy-engine application map other optimize DRE

Configures the WAE's optimize DRE command action for nonclassified traffic.

global configuration

application-accelerator

(config) policy-engine application map other optimize full

Configures the application policy for nonclassified traffic with the optimize full command action.

global configuration

application-accelerator

(config) policy-engine application map other pass-through

Configures the application policy for nonclassified traffic with the pass-through command action.

global configuration

application-accelerator

(config) policy-engine application name

Creates a new application definition that specifies general information about an application.

global configuration

application-accelerator

(config) policy-engine application set-dscp

Sets the default DSCP marking value.

global configuration

application-accelerator

(config) policy-engine config

Removes all of the application policy configuration or restores the application policy factory defaults on a WAE.

global configuration

application-accelerator

(config) port-channel

Configures the port channel load-balancing options.

global configuration

All

(config) primary-interface

Configures a primary interface for the WAAS device.

global configuration

All

(config) print-services

Enables and disables WAAS print services and configures an administrative group.

global configuration

All

pwd

Displays the present working directory.

user-level EXEC and privileged-level EXEC

All

(config) radius-server

Configures the RADIUS parameters on a WAAS device.

global configuration

All

(config-preposition) recursive

Enables or disables recursion for a preposition directive.

preposition configuration

application-accelerator

reload

Halts a device and performs a cold restart.

privileged-level EXEC

All

rename

Renames a file.

privileged-level EXEC

All

restore

Restores a device to its manufactured default status.

privileged-level EXEC

All

(config-ca) revocation-check

Configures the certification authority revocation checking method.

certification authority configuration

All

(config-pki-global-settings) revocation-check

Configures the the global settings revocation checking method.

PKI global-settings configuration

All

rmdir

Removes a directory.

privileged-level EXEC

All

(config-preposition) root

Sets the root directory for a preposition directive.

preposition configuration

application-accelerator

(config-preposition) scan-type

Sets the file scanning type for a preposition directive.

preposition configuration

application-accelerator

(config-preposition) schedule

Sets the schedule for a preposition directive.

preposition configuration

application-accelerator

scp

Specifies the SCP client.

privileged-level EXEC

All

script

Checks the errors in a script or executes a script.

privileged-level EXEC

All

(config-preposition) server

Sets the file server for a preposition directive.

preposition configuration

application-accelerator

setup

Configures the basic configuration settings. Invokes the interactive setup utility.

privileged-level EXEC

All

show aaa accounting

Displays the AAA accounting configuration.

privileged-level EXEC

All

show accelerator

Displays the status and configuration of the application accelerators.

user-level EXEC and privileged-level EXEC

application-accelerator

show alarms

Displays information on various types of alarms, their status, and history.

privileged-level EXEC

All

show arp

Displays the ARP entries.

user-level EXEC and privileged-level EXEC

All

show authentication

Displays the authentication configuration.

user-level EXEC and privileged-level EXEC

All

show auto-discovery

Displays auto-discovery information for a WAE.

user-level EXEC and privileged-level EXEC

application-accelerator

show auto-register

Displays the status of the autoregistration feature for a WAE.

privileged-level EXEC

application-accelerator

show banner

Displays the message of the day, login, and EXEC banner settings.

privileged-level EXEC

All

show bypass

Displays the bypass configuration of a WAE.

user-level EXEC and privileged-level EXEC

application-accelerator

show cdp

Displays the CDP configuration.

user-level EXEC and privileged-level EXEC

All

show cifs

Displays CIFS run-time information.

user-level EXEC and privileged-level EXEC

application-accelerator

show clock

Displays the system clock.

user-level EXEC and privileged-level EXEC

All

show cms

Displays the management service information.

user-level EXEC and privileged-level EXEC

All

show cms secure-store

Displays the secure disk encryption status.

privileged-level EXEC

All

show crypto

Displays crypto layer information.

user-level EXEC and privileged-level EXEC

All

show debugging

Displays the state of each debugging option.

user-level EXEC and privileged-level EXEC

All

show device-mode

Displays the device mode.

user-level EXEC and privileged-level EXEC

All

show directed-mode

Displays directed mode information.

user-level EXEC and privileged-level EXEC

application-accelerator

show disks

Displays the disk configurations.

user-level EXEC and privileged-level EXEC

All

show egress-methods

Displays the egress method that is configured and that is being used on a particular WAE.

user-level EXEC and privileged-level EXEC

application-accelerator

show filtering list

Displays TFO flow information for a WAE.

user-level EXEC and privileged-level EXEC

application-accelerator

show flash

Displays the flash memory information.

user-level EXEC and privileged-level EXEC

All

show hardware

Displays the system hardware information.

user-level EXEC and privileged-level EXEC

All

show hosts

Displays the IP domain name, name servers, IP addresses, and host table.

user-level EXEC and privileged-level EXEC

All

show inetd

Displays the status of TCP/IP services.

user-level EXEC and privileged-level EXEC

All

show interface

Displays the hardware interface information.

user-level EXEC and privileged-level EXEC

All

show inventory

Displays the system inventory information.

user-level EXEC and privileged-level EXEC

All

show ip access-list

Displays the information about access lists that are defined and applied to specific interfaces or applications.

user-level EXEC and privileged-level EXEC

All

show ip routes

Displays the IP routing table.

user-level EXEC and privileged-level EXEC

All

show kdump

Displays the kernel crash dump information.

privileged-level EXEC

All

show kerberos

Displays the Kerberos authentication configuration.

user-level EXEC and privileged-level EXEC

All

show license

Displays the license information.

user-level EXEC and privileged-level EXEC

All

show logging

Displays the system logging configuration.

user-level EXEC and privileged-level EXEC

All

show memory

Displays the memory blocks and statistics.

user-level EXEC and privileged-level EXEC

All

show ntp

Displays the NTP configuration status.

user-level EXEC and privileged-level EXEC

All

show policy-engine application

Displays the display application policy information.

user-level EXEC and privileged-level EXEC

application-accelerator

show policy-engine status

Displays the policy-engine high-level information. This information includes the usage of the available resources, which include application names, classifiers, and conditions

user-level EXEC and privileged-level EXEC

application-accelerator

show print-services

Displays the print services administrator and process information.

user-level EXEC and privileged-level EXEC

All

show processes

Displays the process status.

user-level EXEC and privileged-level EXEC

All

show radius-server

Displays the RADIUS server information.

user-level EXEC and privileged-level EXEC

All

show running-config

Displays the current operating configuration.

user-level EXEC and privileged-level EXEC

All

show services

Displays information related to services.

user-level EXEC and privileged-level EXEC

All

show smb-conf

Displays the smb-conf configurations.

user-level EXEC and privileged-level EXEC

All

show snmp

Displays the SNMP statistics.

user-level EXEC and privileged-level EXEC

All

show ssh

Displays the status and configuration of the Secure Shell (SSH) service.

user-level EXEC and privileged-level EXEC

All

show startup-config

Displays the startup configuration.

user-level EXEC and privileged-level EXEC

All

show statistics accelerator

Displays the application accelerator statistics information.

user-level EXEC and privileged-level EXEC

application-accelerator

show statistics aoim

Displays AO (accelerator) Information Manager statistics.

privileged-level EXEC

application-accelerator

show statistics application

Displays the status of the application statistics.

privileged-level EXEC

All

show statistics authentication

Displays the authentication statistics.

user-level EXEC and privileged-level EXEC

All

show statistics auto-discovery

Displays TFO auto-discovery statistics for a WAE.

user-level EXEC and privileged-level EXEC

application-accelerator

show statistics cifs

Displays the CIFS statistics information.

user-level EXEC and privileged-level EXEC

application-accelerator

show statistics connection

Displays the connection statistics for a WAE.

user-level EXEC and privileged-level EXEC

application-accelerator

show statistics connection auto-discovery

Displays the auto-discovery connection statistics for a WAE.

user-level EXEC and privileged-level EXEC

application-accelerator

show statistics connection closed

Displays the closed connection statistics for a WAE.

user-level EXEC and privileged-level EXEC

application-accelerator

show statistics connection conn-id

Displays the connection ID statistics for a WAE.

user-level EXEC and privileged-level EXEC

application-accelerator

show statistics connection egress-methods

Displays detailed egress method-related information about the connection segments for a WAE.

privileged-level EXEC

application-accelerator

show statistics connection optimized

Displays optimized information about the connection segments for a WAE.

privileged-level EXEC

application-accelerator

show statistics connection pass-through

Displays pass through information about the connection segments for a WAE.

privileged-level EXEC

application-accelerator

show statistics crypto ssl ciphers

Displays crypto SSL cipher usage statistics.

privileged-level EXEC

application-accelerator

show statistics datamover

Displays internal datamover information.

user-level EXEC and privileged-level EXEC

application-accelerator

show statistics directed-mode

Displays directed mode statistics.

user-level EXEC and privileged-level EXEC

application-accelerator

show statistics dre

Displays the Data Redundancy Elimination (DRE) statistics for a WAE.

user-level EXEC and privileged-level EXEC

application-accelerator

show statistics filtering

Displays TFO flow statistics for a WAE.

user-level EXEC and privileged-level EXEC

application-accelerator

show statistics flow

Displays the flow statistics.

user-level EXEC and privileged-level EXEC

application-accelerator

show statistics generic-gre

Displays the generic GRE tunnel statistics.

user-level EXEC and privileged-level EXEC

application-accelerator

show statistics icmp

Displays the ICMP statistics.

user-level EXEC and privileged-level EXEC

All

show statistics ip

Displays the IP statistics.

user-level EXEC and privileged-level EXEC

All

show statistics netstat

Displays the Internet socket connection statistics.

user-level EXEC and privileged-level EXEC

All

show statistics pass-through

Displays the pass-through statistics.

user-level EXEC and privileged-level EXEC

application-accelerator

show statistics peer

Displays the DRE peer statistics for a WAE.

user-level EXEC and privileged-level EXEC

application-accelerator

show statistics radius

Displays the RADIUS authentication statistics.

user-level EXEC and privileged-level EXEC

All

show statistics services

Displays the services statistics.

user-level EXEC and privileged-level EXEC

All

show statistics snmp

Displays the SNMP statistics.

user-level EXEC and privileged-level EXEC

All

show statistics synq

Displays statistics for the SynQ module.

user-level EXEC and privileged-level EXEC

application-accelerator

show statistics tacacs

Displays the TACACS+ authentication and authorization statistics.

user-level EXEC and privileged-level EXEC

All

show statistics tcp

Displays the Transmission Control Protocol statistics.

user-level EXEC and privileged-level EXEC

All

show statistics tfo

Displays the Transport Flow Optimization (TFO) statistics for a WAE.

user-level EXEC and privileged-level EXEC

application-accelerator

show statistics udp

Displays the User Datagram Protocol (UDP) statistics.

user-level EXEC and privileged-level EXEC

All

show statistics wccp

Displays the WCCP statistics for a WAE.

user-level EXEC and privileged-level EXEC

application-accelerator

show statistics windows-domain

Displays the Windows domain configuration.

user-level EXEC and privileged-level EXEC

All

show statistics windows-print requests

Displays the Windows print accelerator statistics.

user-level EXEC and privileged-level EXEC

application-accelerator

show synq list

Displays connections for the SynQ module.

user-level EXEC and privileged-level EXEC

application-accelerator

show sysfs volumes

Displays the system file system (SYSFS) information.

user-level EXEC and privileged-level EXEC

All

show tacacs

Displays the TACACS+ configuration.

user-level EXEC and privileged-level EXEC

All

show tcp

Displays the TCP configuration.

user-level EXEC and privileged-level EXEC

All

show tech-support

Displays the system information for Cisco technical support.

user-level EXEC and privileged-level EXEC

All

show telnet

Displays the Telnet services configuration.

user-level EXEC and privileged-level EXEC

All

show tfo tcp

Displays TFO TCP buffer information.

user-level EXEC and privileged-level EXEC

application-accelerator

show transaction-logging

Displays the transaction logging information for a WAE.

user-level EXEC and privileged-level EXEC

application-accelerator

show user

Displays information about a particular user.

user-level EXEC and privileged-level EXEC

All

show users administrative

Displays the administrative users.

user-level EXEC and privileged-level EXEC

All

show version

Displays the software version.

user-level EXEC and privileged-level EXEC

All

show virtual-blade

Displays virtual blade information on your WAE device.

privileged-level EXEC

application-accelerator

show wccp

Displays the WCCP information for a WAE.

user-level EXEC and privileged-level EXEC

application-accelerator

show windows-domain

Displays the Windows domain configuration.

user-level EXEC and privileged-level EXEC

All

(config-if) shutdown

Shuts down the specified interface.

interface configuration

All

shutdown

Shuts down the device (stops all applications and operating system).

privileged-level EXEC

All

(config) smb-conf

Manually configures parameters in the Samba configuration file, smb-conf.

global configuration

All

(config) snmp-server access-list

Configures an access control list to allow access through an SNMP agent.

global configuration

All

(config) snmp-server community

Enables SNMP; sets the community string, optionally names the group, and enables the read-write access with the community string.

global configuration

All

(config) snmp-server contact

Specifies the text for the system contact MIB object.

global configuration

All

(config) snmp-server enable traps

Enables the SNMP traps.

global configuration

All

(config) snmp-server group

Defines a user security model group.

global configuration

All

(config) snmp-server host

Specifies the hosts to receive SNMP traps.

global configuration

All

(config) snmp-server location

Specifies the path for MIB object sysLocation.

global configuration

All

(config) snmp-server mib

Configures the persistence for the SNMP Event MIB.

global configuration

All

(config) snmp-server notify inform

Configures the SNMP inform request.

global configuration

All

(config) snmp-server trap-source

Configures the SNMP trap source.

global configuration

All

(config) snmp-server user

Defines a user who can access the SNMP engine.

global configuration

All

(config) snmp-server view

Defines an SNMPv2 MIB view.

global configuration

All

snmp trigger

Creates or deletes SNMP triggers on a MIB variable.

privileged-level EXEC

All

ssh

Allows secure encrypted communications between an untrusted client machine and a WAAS device over an insecure network.

user-level EXEC and privileged-level EXEC

All

(config) sshd

Configures the parameters for the Secure Shell (SSH) service.

global configuration

All

(config) ssh-key-generate

Generates a SSH host key.

global configuration

All

(config-if) standby

Configures an interface to be a backup for another interface.

interface configuration

All

(config) tacacs

Configures the TACACS+ parameters on a WAAS device.

global configuration

All

(config) tcp

Configures the TCP parameters.

global configuration

All

tcpdump

Dumps the TCP traffic on the network.

privileged-level EXEC

All

telnet

Starts the Telnet client.

user-level EXEC and privileged-level EXEC

All

(config) telnet enable

Enables the Telnet services.

global configuration

All

terminal

Sets the terminal output commands.

user-level EXEC and privileged-level EXEC

All

test

Performs diagnostic tests and displays the results.

user-level EXEC and privileged-level EXEC

All

tethereal

Analyzes network traffic from the command line.

privileged-level EXEC

All

(config) tfo exception

Configures TFO exception handling.

global configuration

application-accelerator

(config) tfo optimize

Configures TFO optimization for DRE or full generic optimization on the WAE.

global configuration

application-accelerator

(config) tfo tcp adaptive-buffer-sizing

Configures TFO optimization with TCP adaptive buffer sizing.

global configuration

application-accelerator

(config) tfo tcp keepalive

Configures TFO optimization with a TCP keepalive on a WAE.

global configuration

application-accelerator

(config) tfo tcp optimized-mss

Configures TFO optimization with an optimized-side TCP maximum segment size on a WAE.

global configuration

application-accelerator

(config) tfo tcp optimized-receive-buffer

Configures TFO optimization with an optimized-side receive buffer on a WAE.

global configuration

application-accelerator

(config) tfo tcp optimized-send-buffer

Configures TFO optimization with an optimized-side send buffer on a WAE.

global configuration

application-accelerator

(config) tfo tcp original-mss

Configures TFO optimization with an unoptimized-side TCP maximum segment size on the WAE.

global configuration

application-accelerator

(config) tfo tcp original-receive-buffer

Configures TFO optimization with an unoptimized-side receive buffer on a WAE.

global configuration

application-accelerator

(config) tfo tcp original-send-buffer

Configures TFO optimization with an unoptimized-side send buffer on a WAE.

global configuration

application-accelerator

traceroute

Traces the route to a remote host.

user-level EXEC and privileged-level EXEC

All

transaction-log

Forces the transaction logging for TFO and export on a WAE.

privileged-level EXEC

application-accelerator

(config) transaction-logs

Configures the transaction logging on a WAE.

global configuration

application-accelerator

type

Displays a file.

user-level EXEC and privileged-level EXEC

All

type-tail

Displays the last several lines of a file.

user-level EXEC and privileged-level EXEC

All

(config) username

Establishes the username authentication.

global configuration

All

virtual-blade

Executes general operations on a virtual blade.

privileged-level EXEC

application-accelerator

(config) virtual-blade

Configures virtual blades on your WAE device.

global configuration

All

(config-vb) vnc

Enables or disables the VNC server for the virtual blade on your WAE.

virtual blade configuration

application-accelerator

wafs

Performs a backup or restores system configuration, and creates a system report on a WAE.

privileged-level EXEC

application-accelerator

(config) wccp access-list

Configures the IP access list for inbound Web Cache Coordination Protocol (WCCP) GRE-encapsulated traffic on a WAE.

global configuration

application-accelerator

(config) wccp flow-redirect

Enables the WCCP flow redirection on a WAE.

global configuration

application-accelerator

(config) wccp router-list

Creates a router list on a WAE for use in the WCCP Version 2 services.

global configuration

application-accelerator

(config) wccp shutdown

Sets the maximum time interval after which the WAE will perform a clean shut down.

global configuration

application-accelerator

(config) wccp tcp-promiscuous mask

Configures the TCP promiscuous mode service (WCCP Version 2 services 61 and 62) on a WAE.

global configuration

application-accelerator

(config) wccp tcp-promiscuous router-list-num

Configures the TCP promiscuous mode service (WCCP Version 2 services 61 and 62) router list on a WAE.

global configuration

application-accelerator

(config) wccp version

Specifies the WCCP version number.

global configuration

application-accelerator

whoami

Displays the name of the current user.

user-level EXEC and privileged-level EXEC

All

windows-domain

Accesses Windows domain utilities.

privileged-level EXEC

All

(config) windows-domain

Configures Windows domain server options.

global configuration

All

write

Writes or erases the startup configurations to NVRAM or to a terminal session, or writes the MIB persistence configuration to disk.

privileged-level EXEC

All