Getting Started Installing or Upgrading a Cisco StadiumVision Director Remote Server
First Published: March 19, 2013
Revised: January 14, 2014
Read this module before you perform an initial installation or upgrade of the Cisco StadiumVision Director Remote Release 3.1 software. It includes the following topics:
Before You Begin
Be sure that you understand and have met the following prerequisites before you begin to install or upgrade the Cisco StadiumVision Director Remote software:
For more information about installing your Cisco UCS C22 hardware, see the Appendix A: Cisco UCS C22 Hardware Installation Guidelines.
-
If you are using a server other than the Cisco UCS C22 server:
– Be sure that the server meets the minimum system requirements described in the Getting Started Installing or Upgrading a Cisco StadiumVision Director Remote Server.
– The server is configured with VMWare ESXi host version 4.1 or 5.1.
-
Verify that the Cisco StadiumVision Director Remote server has power and is connected to the network using the Ethernet port eth0 on the rear panel.
-
A monitor and keyboard are connected to the server.
-
Be sure to have the network information required to configure the Ethernet connection on the Cisco StadiumVision Director Remote server, such as:
– IP address (IPv4 only) and network mask
– Default gateway address
– DNS server address
– Hostname
-
You have internet access from a computer running Microsoft Windows to download the following software:
– Cisco StadiumVision Director Remote software from Cisco.com.
– VMware vSphere ESXi software (as required)
– VMware vSphere client software (requires Microsoft Windows ) (as required).
Hardware Prerequisites
You can use your own server or install a Cisco UCS C22 server to run the Cisco StadiumVision Director Remote software. Be sure that your configuration meets the miminum system requirements in
Table 1
and supports a VMware ESXi virtualized environment.
Note Cisco StadiumVision Director Remote servers are meant to be physically located close to the DMPs that they operate with, such as at the remote venue edge, and communicating to the players over a LAN. For information about installation-related licensing compliance, see the “Installation Requirements for Licensing Compliance” section of the Release Notes for Cisco StadiumVision Director Release 3.1.
Table 1 Minimum System Requirements for the Cisco StadiumVision Director Remote Server
|
|
Hard Drive Capacity
|
300 GB
Note The hard drives must be configured as a single logical volume. A RAID volume is strongly recommended.
|
Processor
|
Single processor equivalent to an Intel Xeon Processor E5-2420 (15 MB cache, 1.90 GHz clock, 7.20 GT/s Intel® QPI)
|
Virtual RAM (VRAM)
|
16 GB
|
Note To get started with installing and configuring a Cisco UCS C22 server, see the Appendix A: Cisco UCS C22 Hardware Installation Guidelines.
Overview of the Installation and Upgrade Process
There are different tasks required to install or upgrade your Cisco StadiumVision Director Remote server for software Release 3.1 depending on your current server environment:
Installing Cisco StadiumVision Director Remote on a Cisco UCS C22 Server for the First Time
The installation process for a new Cisco UCS C22 server running Cisco StadiumVision Director Remote Release 3.1 for the first time involves the following tasks:
-
Installation of the Cisco UCS C22 hardware.
-
Installation of VMware ESXi host software on the Cisco UCS C22 server.
-
Installation of VMware vSphere client software on a laptop computer used to access the ESXi host on the Cisco UCS C22 server.
-
Deployment of the Cisco StadiumVision Director Remote Open Virtual Appliance (OVA) template.
For detailed information, see the Installing Cisco StadiumVision Director Remote Software on a Server for the First Time.
Installing Cisco StadiumVision Director Remote on Your Own Server Hardware
You can use your own server hardware that meets the minimum system requirements to install Cisco StadiumVision Director Remote. The installation process for a new server running Cisco StadiumVision Director Remote Release 3.1 involves the following tasks:
Note If the server hardware already has the required VMware ESXi host version installed and you also have the VMware vSphere Client software installed, then you only need to deploy the Cisco StadiumVision Directore Remote OVA template.
-
Installation of VMware ESXi host software on the server (as needed).
-
Installation of VMware vSphere client software on a laptop computer used to access the ESXi host on the server (as needed).
-
Deployment of the Cisco StadiumVision Director Remote OVA template.
For detailed information, see the Installing Cisco StadiumVision Director Remote Software on a Server for the First Time.
Upgrading an Existing Cisco StadiumVision Director Remote Server
The software upgrade process for an existing Cisco StadiumVision Director Remote server is performed as an ISO upgrade using the Text Utility Interface (TUI) similar to the process for Cisco StadiumVision Director.
The upgrade process for Cisco StadiumVision Director Release 3.1 involves the following tasks:
-
Downloading the ISO upgrade file from Cisco.com.
-
Uploading the ISO upgrade file to the Cisco StadiumVision Director Remote server.
-
Installing the ISO upgrade image on the Cisco StadiumVision Director Remote server.
For detailed information, see the Upgrading Cisco StadiumVision Director Remote Software.