Guest

Cisco BPX 8600 Series Switches

Connecting an MGX 8220 AUSM-8T1/B to a 3620 Using IMA Trunks Sample Configuration

Cisco - Connecting an MGX 8220 AUSM-8T1/B to a 3620 Using IMA Trunks Sample Configuration

Document ID: 22203

Updated: Oct 23, 2009

   Print

Introduction

This document provides configuration information for a service-interworking (SIW) connection over an inverse multiplexing for ATM (IMA) trunk group. The configuration for each device is created using the command line interface (CLI). The SIW connection establishes IP connectivity between a Cisco 3620 router ATM interface and a Cisco MC 3810 frame relay interface. The four T1 IMA trunk groups are established between the 3620 router T1 IMA and MGX 8220 AUSM-8T1/B service modules. The MGX 8220 is connected as a feeder shelf to the BPX 8600. The BPX 8600 provides the switching from the AUSM-8T1/B ATM connection to the FRSM-8T1 frame relay connection on the same MGX 8220. The MGX 8220 FRSM-8T1 service module provides the SIW conversion from ATM (aal5snap encapsulation) to frame relay (IETF encapsulation).

This document is intended to be used as an aid for configuring Cisco equipment, but is not a substitute for proper network design and planning with your Cisco Sales Engineer, Systems Engineer, or Account Manager.

Prerequisites

Requirements

There are no specific requirements for this document.

Components Used

The information in this document is based on these software and hardware versions:

  • 3620:

    • Software - Cisco IOS® Software Release 12.1(1a)T1.

    • Hardware - Cisco 3620 with 8-port T1 IMA network interface.

  • MC 3810

    • Software - Cisco IOS Software Release 12.0(4)T.

    • Hardware - Cisco MC 3810 with T1 multi-flex trunk (MFT) interface.

  • MGX 8220

    • Firmware - Cisco release 5.0.14 and the appropriate versions of service module hardware and firmware. Refer to the WAN Switching Software Center (registered customers only) .

    • Hardware - Cisco AUSM model B service module is used for ATM Forum compliant IMA. Four T1 trunks are used to connect between the 8-port AUSM-8T1/B service module and the 8-port 3620 T1 IMA module. Both the AUSM-8T1/B and 3620 T1 IMA service modules use RJ48 connectors.

    • FRSM-8T1 service module uses RJ48 connectors.

  • BPX 8600

    • Software - Cisco switch software release 9.1.18 and the appropriate versions of card hardware and firmware as specified in the Release Notes.

    • Hardware - The BPX 8600 is connected to the MGX 8220 feeder shelf using a BNI-T3 card set.

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Conventions

For more information on document conventions, refer to the Cisco Technical Tips Conventions.

Configure

In this section, you are presented with the information to configure the features described in this document.

Note: To find additional information on the commands used in this document, use the Command Lookup Tool (registered customers only) .

Network Diagram

This document uses this network setup:

ausmb_3640config.gif

3620 Router

Configure ATM interfaces as an IMA group and assign IP address to the logical IMA interface. All show command output is in the Show Command section of this document. For additional show commands and troubleshooting information, refer to Troubleshooting ATM IMA Links on Cisco 2600 and 3600 Routers.

r3620(config)#interface atm0/0 
  r3620(config-if)#ima-group 1
  
!-1- Add the interface to IMA group 1.

  r3620(config-if)#no shut
  r3620(config-if)#int atm0/1 
  r3620(config-if)#ima-group 1
  
!--- Each interface must be added to IMA group 1.

  r3620(config-if)#no shut
  r3620(config)#int atm0/2
  r3620(config-if)#ima-group 1
  r3620(config-if)#no shut
  r3620(config)#int atm0/3
  r3620(config-if)#ima-group 1
  r3620(config-if)#no shut
  r3620(config-if)#int ATM0/IMA1.10 point-to-point
  
!--- Configure the IMA interface.

  r3620(config-subif)#ip add 2.2.2.1 255.255.255.0
  r3620(config-subif)#ima active-links-minimum 1
  r3620(config-subif)#ima differential-delay-maximum 75
  r3620(config-subif)#pvc IMA-VC 10/20
  r3620(config-if-at)#protocol ip 10.1.1.2 broadcast
  r3620(config-if-at)#encapsulation aal5snap
  r3620(config-if-at)#vbr-nrt 512 384 128
  
!--- Set the connection type. 

This output is the minimum number of active links required for the IMA group to be operational. The default value is 1.

ima active-links-minimum 1

This output is the maximum timing delay that can exist among the active links in the IMA group. The default value is 25 milliseconds (msec).

ima differential-delay-maximum 75

This output specifies a non-realtime variable bit-rate connection with a Peak Cell Rate (PCR) of 512 kbps, sustained cell rate (SCR) of 384 kbps, and Maximum Burst Size (MBS) of 128 cells.

vbr-nrt 512 384 128

Configuring traffic-shaping parameters for PCR, SCR, and MBS on the router is important to avoid data loss caused by discards on the switch. When traffic-shaping parameters are not configured on the router, the initial router burst of data may be transmitted at port speed. In this example with four physical T1s composing one IMA port, the port speed is high. If the switch is not configured to accept large initial bursts, data is discarded.

MGX 8220 AUSM-8T1/B

Issue the StrataCom-level dspfeature command to verify the IMA feature is enabled on the AUSM-8T1/B service module. If StrataCom-level access is not available, proceed with the configuration.

a1.1.10.AUSMB8.a > dspfeature

  Channelized:  Off
  Rate Control:  On
  IMA feature:  On

If IMA feature is off or you are unable to add the IMA group, contact Cisco Technical Support (registered customers only) for assistance with enabling this feature.

Add the lines on the AUSM-8T1/B card that are included in the IMA group. The relationship between the AUSM-8T1/B and 3620 T1 IMA lines is shown here.

Service Module Physical Ports
3620 T1 IMA 0, 1, 2, 3
AUSM-8T1/B 1, 2, 3, 4

a1.1.10.AUSMB8.a > addln 1 
a1.1.10.AUSMB8.a > addln 2 
a1.1.10.AUSMB8.a > addln 3 
a1.1.10.AUSMB8.a > addln 4 

Check all the lines and clear any alarms before adding them into the IMA group. Using contiguous lines in an IMA group is recommended but not required. An IMA group can be composed of lines 1, 3, 4, and 5. Note that line framing and line coding for the T1s between the AUSM/B and 3620 must match. For IMA groups that span international boundaries, configure network clock sources before you add the lines.

a1.1.10.AUSMB8.a > dsplns 

  Line   Conn      Type      Status/Coding    Length      XmtClock  Alarm   Stats
         Type                                             Source            Alarm 
  ----   -----  ------------ -------------- ------------- --------  -----   -----
  14.1   RJ-48  dsx1ESF      Ena/dsx1B8ZS     0-131 ft    LocalTim   No      No
  14.2   RJ-48  dsx1ESF      Ena/dsx1B8ZS     0-131 ft    LocalTim   No      No
  14.3   RJ-48  dsx1ESF      Ena/dsx1B8ZS     0-131 ft    LocalTim   No      No
  14.4   RJ-48  dsx1ESF      Ena/dsx1B8ZS     0-131 ft    LocalTim   No      No
  14.5   RJ-48  dsx1ESF      Dis/dsx1B8ZS     0-131 ft    LocalTim
  14.6   RJ-48  dsx1ESF      Dis/dsx1B8ZS     0-131 ft    LocalTim
  14.7   RJ-48  dsx1ESF      Dis/dsx1B8ZS     0-131 ft    LocalTim
  14.8   RJ-48  dsx1ESF      Dis/dsx1B8ZS     0-131 ft    LocalTim

 LineNumOfValidEntries: 8
  
a1.1.10.AUSMB8.a > dspalms -ds1

 Line  AlarmState   StatisticalAlarmState
 ----  -----------  ---------------------
 14.1  No Alarms    No Statistical Alarms
 14.2  No Alarms    No Statistical Alarms 
 14.3  No Alarms    No Statistical Alarms 
 14.4  No Alarms    No Statistical Alarms 

Add the IMA group and include all the above added lines into the group. If the IMA group does not clear the alarm after it is added at each end of the network, try to add one trunk IMA group and successive trunks one-by-one.

a1.1.10.AUSMB8.a > addimagrp 1 1 1.2.3.4 1 
User Input Definition
addimagrp Add IMA Group.
1 IMA group number—Value that ranges from 1 to 8.
1 Port Type -- 1 - UNI, 2 - NNI
1.2.3.4 List of links—List of links separated by dots.
1 minimum no of links—Minimum number of links for the group formation. The values range from 1 to 8.

Note: This number must be the same at each end of the IMA group. In this case one end of the IMA group is at the 3620, the other end is at the AUSM-8T1/B.

a1.1.10.AUSMB8.a > dspaimgrp 1 
   IMA Group number                 : 1 
   Port type                        : UNI 
   Lines configured                 : 1.2.3.4 
   Enable                           : Enabled 
   IMA Port state                   : Active 
   IMA Group Ne state               : operational 
   PortSpeed (cells/sec)            : 14364 
   GroupTxAvailCellRate (cells/sec) : 14364 
   ImaGroupTxFrameLength(cells)     : 128 
   LcpDelayTolerance (IMA frames)   : 1 
   ReadPtrWrPtrDiff  (cells)        : 4 
   Minimum number of links          : 1 
   MaxTolerableDiffDelay (msec)     : 275 
   Lines Present                    : 1.2.3.4 

!--- Verify all configured links are present. 

   ImaGroupRxImaId                  : 0x2 
   ImaGroupTxImaId                  : 0x2 
   Observed Diff delay (msec)       : 0 
   Clock Mode                       : CTC 
   GroupAlpha                       : 2 
   GroupBeta                        : 2 
   GroupGamma                       : 1 

Type <CR> to continue, Q<CR> to stop: 


   GroupConfiguration               : 1 
   IMAGrp Failure status            : No Failure 
   Timing reference link            : 3 

Verify the AUSM-8T1/B IMA port payload scrambling configuration is the same as that of the 3620 interface. Payload scrambling was developed to ensure that ATM cell payload does not resemble cell header and is only locally significant. Specifically, each side of an ATM interface must have the same payload scrambling value, but all ATM interfaces in the network do not require the same configuration.

a1.1.10.AUSMB8.a > dspports 

  

No ATM T1/E1 UNI ports currently active 

 List of IMA groups: 
 =================== 

ImaGrp PortType  Conf  Avail  Lines configured  Lines present   Tol Diff  Port e 
                 rate   rate                                    Delay(ms) 
------ -------- -----  ------  ---------------  --------------- --------- ------ 
 14.1   UNI     14364   3591  1.2.3.4          1.2.3.4           275      Active 

  NextPortNumAvailable:  8 

a1.1.10.AUSMB8.a > dspplpp 1 

  PhysicalPortNumber:            1 
  CellFraming:                   ATM 
  CellScramble:                  No Scramble 
  Plpp Loopback:                 No Loopback 
  Single-bit error correction:   Disabled

Now add a VBR connection to the IMA port with VPI 10 and VCI 20.

a1.1.10.AUSMB8.a > addcon 200 0 1 10 20 2 
User Input Definition
addcon Add a connection to the current AUSM.
200 channel number—Value that ranges from 16 to 1015.
0 Connection Type—Connection Type : 0 - VCC , non zero - Local VP Id of the VPC (1 to 20(UNI)/100(STI)/340(NNI))
1 port number—Values that range from 1 to 8.
10 Channel VPI—Virtual Path Identifier: 0 - 255. Must match VPI on 3620.
20 Channel VCI—Virtual Channel Identifier: 0 - 65535 for VCC, * for VPC. Must match VCI on 3620.
2 Service Type—Service Type: 1 - CBR, 2 - VBR, 3 - ABR, 4 - UBR. Should match connection type on 3620.

Configure the VBR connection values to reflect those of the 3620. The connection values are not optimized and are used for example only.

a1.1.10.AUSMB8.a > cnfupcvbr

ERR : incorrect number of parameters (not enough)
Syntax : cnfupcvbr "chan_num enable pcr[0+1] cdvt[0+1] scr scr_police
                    mbs IngPcUtil EgSrvRate EgPcUtil clp_tag "

         Channel # -- Channel Number : 16 - 1015
         Enable/Disable -- UPC : 1 - Disable, 2 - Enable
         PeakCellRate -- PCR [0+1]: 10-PortRate(T1-3622,E1-4528,clearE1-4830),
                For IMA,T1-3591,E1-4490,clrE1-4789, multiply rate by #links
         CDVT[0+1] -- Cell Delay Variation [0+1]: 1 - 250000 micro_secs
         SCR -- Sustained Cell Rate:10-PortRate(T1-3622,E1-4528,clearE1-4830),
                For IMA,T1-3591,E1-4490,clrE1-4789, multiply rate by #links
         SCR Policing -- 1 - CLP[0] Cells, 2 - CLP[0+1] Cells, 3 - No SCR Policg
         Maximum Burst -- 1 - 5000 cells
         IngPcUtil -- Ingress percentage util: 1 to 127.  0 for default
         EgSrvRate -- Egress service rate:1-PortRate(T1-3622,E1-4528,clearE1-48,
                For IMA,T1-3591,E1-4490,clrE1-4789, multiply rate by #links
         EgPcUtil -- Egress percentage util: 1 to 127.  0 for default
         Clp Tagging -- CLP TAG Enable : 1 - Disable, 2 - Enable

a1.1.10.AUSMB8.a > cnfupcvbr 200 2 3622 25000 2048 1 1000 100 2633 100 2

MC 3810

r3a#conf t
  r3a(config)#cont t1 0
  r3a(config-controller)#framing esf
  r3a(config-controller)#linecode b8zs
  r3a(config-controller)#channel-group 0 timeslots 1-24 speed 64
  r3a(config-controller)#no shut 
  r3a(config-controller)#int s0:0
  r3a(config-if)#ip address 2.2.2.2 255.255.255.0
  r3a(config-if)#encapsulation frame-relay IETF
  r3a(config-if)#frame-relay map ip 2.2.2.1 100 broadcast 
  
!-- associate the DLCI to the IP address

  r3a(config-if)#no shut 

MGX 8220 FRSM

Verify the existing lines.

a1.1.9.FRSM.a > dsplns 
  Line  Conn  Type     Status/Coding      Length     XmtClock Alarm Stats 
        Type                                         Source         Alarm 
  ----  ----- -------  -------------     ---------   -------- ----- ----- 
  6.1   DB-15 dsx1ESF  Dis/dsx1B8ZS       0-110 ft   LocalTim 
  6.2   DB-15 dsx1ESF  Dis/dsx1B8ZS       0-110 ft   LocalTim 
  6.3   DB-15 dsx1ESF  Dis/dsx1B8ZS       0-110 ft   LocalTim 
  6.4   DB-15 dsx1ESF  Dis/dsx1B8ZS       0-110 ft   LocalTim 

  LineNumOfValidEntries: 4 

Enable the line connected to the MC 3810 router. Note that line framing and line coding for the T1 between the FRSM and MC 3810 must match.

a1.1.9.FRSM.a > addln 1 

Enable the logical port and configure for frame-relay service.

a1.1.9.FRSM.a > addport 1 1 2 1 24 1
User Input Definition
addport Add a Port
1 port number—Values that range from 1 to192 are accepted for T1 and 1-2481.
1 line number—Value that ranges from 1 to 8.
2 DS0 speed—1 for 56 K, 2 for 64 K
1 beginning slot—Beginning time slot in 1 base.
24 number of slot—Number of DS0 time slots assigned to.
1 port type—Values 1-3, 1=frame relay, 2=FUNI mode-1a, 3=frForward

Configure the logical port to use local management interface (LMI) signaling. This example uses StrataLMI with asynchronous updates enabled and enhanced LMI disabled.

a1.1.9.FRSM.a > cnfport 1 S 2 n 
User Input Definition
cnfport Configure Port
1 port number—Values that range from 1 to 192 are accepted for T1 and 1 to 2481 for E1.
S LMI signaling—(N)one (S)trataLMI au-AnnexAUNI du-AnnexDUNI an-AnnexANNI dn-AnnexDNNI. Must match LMI on MC 3810.
2 asyn UPD/UFS —(UPD = Update Status, UFS = Unsolicited Full Status) (n or 1) = both dis, (y or 2) = UPD en, 3 = UFS en, 4 = both en
n Enhanced LMI—(N or n) disable (Y or y) enable

Display and verify the configuration of the logical port.

a1.1.9.FRSM.a > dspports 

  Port   Ena/Speed   EQServ  SignalType  T391 T392 N391 N392 N393 Type    I 
                     Ratio 
  ------ ----------- ------ ------------ ---- ---- ---- ---- ---- --------- 
  6.1.1  Mod/1536 Kbps  1   StrataLMI    10   15    6    3    4 frameRel 

  Number of ports:              1 

  PortDs0UsedLine1:             0x00ffffff 
  PortDs0UsedLine2:             0x00000000 
  PortDs0UsedLine3:             0x00000000 
  PortDs0UsedLine4:             0x00000000 
  PortNumNextAvailable:         7 

Add the connection and enable service internetworking translation. Note that connection values are not optimized and are used for example only.

a1.1.9.FRSM.a > addchan 100 1 100 1536000 3 
User Input Definition
addchan Add a channel to the current FRSM
100 channel number—Value that ranges from 16 to 1015.
1 port number—Values that range from 1 to 192 are accepted for T1 and 1 to 2481 for E1.
100 DLCI number—Value that ranges from 0 to 1023. Must match DLCI on MC 3810.
1536000 committed rate -- 0-1536000 bps for T1; 0-2048000 bps for E1.
3 chan type—Values 1 to 5, 1=NIW 2=SIW-transparent 3=SIW-xlation 4=FUNI 5=frForward

BPX 8600

Add the MGX 8220 as a feeder shelf to the BPX 8600 switch. Issue the uptrk command to activate the T3 trunk.

b3             TRM   SuperUser       BPX 8600  9.1.18    Oct. 6 2000  10:48 GMT 
TRK     Type     Current Line Alarm Status               Other End 
 2.1    T3       Clear - OK                              - 
  

Last Command: uptrk 2.1 
  

Next Command: 

Check the trunk and clear any alarms. Once the trunk is clear of alarms, issue the addshelf command.

b3             TRM   SuperUser       BPX 8600  9.1.18    Oct. 6 2000  10:54 GMT 
                   BPX 8600 Interface Shelf Information 

Trunk    Name      Type          Part Id   Ctrl Id   Alarm 
 2.1     a1        AXIS             -         -      MIN 
  

Last Command: addshelf 2.1 A 

Shelf has been added 
Next Command: 

Add the connection on the BPX 8600 switch by issuing the addcon command. The connection values are not optimized for frame relay to ATM service interworking and are used for example only. For more information about ATM connection configuration and troubleshooting, refer to ATM Connection Configuration and Troubleshooting for the Cisco BPX 8600 Series Switch and Troubleshooting ATM PVC Problems.

addcon 2.1.9.100 b3 2.1.10.200 atfr 2000/2000 * 25000/25000 1000/1000 * * * * *
User Input Definition
addcon Add a connection.
2.1.9.100 connection number — <feeder_trunk_slot.feeder_trunk_port.FRSM_slot.FRSM_channel>
b3 remote node name—Repeat the name for locally-switched connections.
2.1.10.200 connection number — <feeder_trunk_slot.feeder_trunk_port.AUSM_slot.AUSM_channel>
atfr connection type —ATM (at) to frame relay (fr)
2000/2000 PCR (0 + 1) [50/50] — Peak Cell Rate. Equivalent to frame relay peak information rate (PIR) for cell loss priority (CLP) 0 and CLP=1 traffic. Default value is 50 in both transmit and receive directions.
100/100 % Util [100/100] — Percent utilization. Default value is 100 in both transmit and receive directions.
25000/25000 CDVT (0 + 1) [250000/250000] — Cell Delay Variation Tolerance. Default value is 250000 in both transmit and receive directions.
1000/1000 SCR [50/50] — Sustainable Cell Rate. Equivalent to frame relay committed information rate (CIR). Default value is 50 in both transmit and receive directions.
1000/1000 MBS [1000/1000] — Maximum Burst Size. Equivalent to frame relay excess burst size (Be). Default value is 1000 in both transmit and receive directions.
3 Policing [3] — The algorithm used to determine conformance to traffic contract. Default value is 3 for ATM Forum Traffic Management Specification Version 4.0 VBR.3.
1280/1280 VC Qdepth [1280/1280] — Virtual Connection Queue Depth. Default value is1280 in both transmit and receive directions.
35/35 EFCI [35/35] — Explicit Forward Congestion Indication. Equivalent to frame relay forward explicit congestion notification (FECN). Configured per port queue for the BXM. Default value is35 in both transmit and receive directions.
1/1 IBS [1/1] — Initial Burst Size. Equivalent to frame relay Cmax. Default value is1 in both transmit and receive directions.

Show Commands

Certain show commands are supported by the Output Interpreter Tool (registered customers only) , which allows you to view an analysis of show command output.

Command summary:

r3620#ping 2.2.2.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 104/136/148 ms


r3620#show version
Cisco Internetwork Operating System Software 
IOS (tm) 3600 Software (C3620-JS-M), Version 12.1(1a)T1,  RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Mon 03-Apr-00 11:10 by ccai
Image text-base: 0x600088F0, data-base: 0x612A6000

ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE ()

r3620 uptime is 4 hours, 27 minutes
System returned to ROM by power-on
System image file is "flash:c3620-js-mz.121-1a.T1"

cisco 3620 (R4700) processor (revision 0x81) with 57344K/8192K bytes of memory.
Processor board ID 10707918
R4700 CPU at 80Mhz, Implementation 33, Rev 1.0
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
16 ATM network interface(s)
DRAM configuration is 32 bits wide with parity disabled.
29K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102
r3620#show run
Building configuration...

Current configuration:
!
version 12.1
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname r3620
!
!
!
!
!
!
ip subnet-zero
no ip domain-lookup
!
cns event-service server
!
!
!
! 
interface ATM0/0
 no ip address
 no atm ilmi-keepalive
 ima-group 1
 no scrambling-payload
!
interface ATM0/1
 no ip address
 no atm ilmi-keepalive
 ima-group 1
 no scrambling-payload
!
interface ATM0/2
 no ip address
 no atm ilmi-keepalive
 ima-group 1
 no scrambling-payload
!
interface ATM0/3
 no ip address
 no atm ilmi-keepalive
 ima-group 1
 no scrambling-payload
!
interface ATM0/4
 no ip address
 shutdown
 no atm ilmi-keepalive
 no scrambling-payload
!
interface ATM0/5
 no ip address
 shutdown
 no atm ilmi-keepalive
 no scrambling-payload
!
interface ATM0/6
 no ip address
 shutdown
 no atm ilmi-keepalive
 no scrambling-payload
!
interface ATM0/7
 no ip address
 shutdown 
 no atm ilmi-keepalive
 no scrambling-payload
!
interface ATM0/IMA1
 no ip address
 no atm ilmi-keepalive
!
interface ATM0/IMA1.10 point-to-point
 ip address 2.2.2.1 255.255.255.0
 pvc 10/20 
  protocol ip 2.2.2.2 broadcast
  encapsulation aal5snap
 !
!
interface ATM1/0
 no ip address
 shutdown
 no atm ilmi-keepalive
 no scrambling-payload
!
interface ATM1/1
 no ip address
 shutdown 
 no atm ilmi-keepalive
 no scrambling-payload
!
interface ATM1/2
 no ip address
 shutdown
 no atm ilmi-keepalive
 no scrambling-payload
!
interface ATM1/3
 no ip address
 shutdown
 no atm ilmi-keepalive
 no scrambling-payload
!
interface ATM1/4
 no ip address
 shutdown
 no atm ilmi-keepalive
 no scrambling-payload
!
interface ATM1/5
hutdown
 no atm ilmi-keepalive
 no scrambling-payload
!
interface ATM1/6
 no ip address
 shutdown
 no atm ilmi-keepalive
 no scrambling-payload
!
interface ATM1/7
 no ip address
 shutdown
 no atm ilmi-keepalive
 no scrambling-payload
!
ip classless
no ip http server
!
!
!
line con 0
 transport input none
line aux 0
line vty 0 4
 login
!
end
r3620#show atm pvc
            VCD /                                      Peak  Avg/Min Burst
Interface   Name       VPI   VCI  Type   Encaps   SC   Kbps   Kbps   Cells  Sts
0/IMA1.10  1           10    20   PVC    SNAP     UBR    1500                UP
r3620#show interface atm0/0
ATM0/0 is up, line protocol is up 
  Hardware is ATM T1
  MTU 4470 bytes, sub MTU 4470, BW 1500 Kbit, DLY 20000 usec, 
     reliability 0/255, txload 1/255, rxload 1/255
  Encapsulation ATM, loopback not set
  Keepalive not supported 
  Encapsulation(s): AAL5
  256 maximum active VCs, 0 current VCCs
  VC idle disconnect time: 300 seconds
  Last input never, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: Per VC Queueing
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     0 packets output, 0 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 output buffer failures, 0 output buffers swapped out
r3620#show atm interface atm0/0
Interface ATM0/0:
AAL enabled:  AAL5 , Maximum VCs: 256, Current VCCs: 0

Maximum Transmit Channels: 0
Max. Datagram Size: 4496
PLIM Type: DS1, Framing is T1 ESF, TX clocking: LINE
Cell-payload scrambling: OFF
0 input, 0 output, 0 IN fast, 0 OUT fast, 0 out drop
 Avail bw = 1500 
Config. is ACTIVE
r3620#show interface ATM0/IMA1
ATM0/IMA1 is up, line protocol is up 
  Hardware is ATM IMA
  MTU 4470 bytes, sub MTU 4470, BW 6000 Kbit, DLY 20000 usec, 
     reliability 236/255, txload 1/255, rxload 1/255
  Encapsulation ATM, loopback not set
  Keepalive not supported 
  Encapsulation(s): AAL5
  256 maximum active VCs, 1 current VCCs
  VC idle disconnect time: 300 seconds
  Last input 00:04:32, output 00:04:32, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: Per VC Queueing
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     41 packets input, 4548 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     493 packets output, 30688 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 output buffer failures, 0 output buffers swapped out
r3620#show interface ATM0/IMA1.10      
ATM0/IMA1.10 is up, line protocol is up 
  Hardware is ATM IMA
  Internet address is 2.2.2.1/24
  MTU 4470 bytes, BW 6000 Kbit, DLY 20000 usec, 
     reliability 236/255, txload 1/255, rxload 1/255
  Encapsulation ATM
  41 packets input, 4548 bytes 
  493 packets output,30688 bytes 
  438 OAM cells input, 438 OAM cells output
  AAL5 CRC errors : 0
  AAL5 SAR Timeouts : 0
  AAL5 Oversized SDUs : 0
r3620#show ima interface atm0/0
Interface ATM0/0 is up
        ifIndex 1, Group Index 1, Row Status is active
        Tx/Rx Lid 0/0, relative delay 0ms
        Ne Tx/Rx state active/active
        Fe Tx/Rx state active/active
        Ne Rx failure status is noFailure
        Fe Rx failure status is noFailure
        Rx test pattern 0x43, test procedure disabled
    IMA Link Current Counters (time elapsed 756 seconds):
        0 Ima Violations, 0 Oif Anomalies
        0 Ne Severely Err Secs, 0 Fe Severely Err Secs
        0 Ne Unavail Secs, 0 Fe Unavail Secs
        0 Ne Tx Unusable Secs, 0 Ne Rx Unusable Secs
        0 Fe Tx Unusable Secs, 0 Fe Rx Unusable Secs
        0 Ne Tx Failures, 0 Ne Rx Failures
        0 Fe Tx Failures, 0 Fe Rx Failures
    IMA Link Total Counters (last 7 15 minute intervals):
        1 Ima Violations, 3 Oif Anomalies
        12 Ne Severely Err Secs, 0 Fe Severely Err Secs
        3600 Ne Unavail Secs, 0 Fe Unavail Secs
        1802 Ne Tx Unusable Secs, 3602 Ne Rx Unusable Secs
        2 Fe Tx Unusable Secs, 0 Fe Rx Unusable Secs
        0 Ne Tx Failures, 8 Ne Rx Failures
        0 Fe Tx Failures, 0 Fe Rx Failures
r3620#show ima interface atm0/ima1 detail
Interface ATM0/IMA1 is up
        Group index is 1
        Ne state is operational, failure status is noFailure
        Active links bitmap 0xF
    IMA Group Current Configuration:
        Tx/Rx configured links bitmap 0xF/0xF
        Tx/Rx minimum required links 1/1
        Maximum allowed diff delay is 25ms, Tx frame length 128
        Ne Tx clock mode CTC, configured timing reference link ATM0/0
        Test pattern procedure is disabled
    Detailed group Information:
        Tx/Rx Ima_id 0x1/0x0, symmetry symmetricOperation
        Number of Tx/Rx configured links 4/4
        Number of Tx/Rx active links 4/4
        Fe Tx clock mode ctc, Rx frame length 128
        Tx/Rx timing reference link 0/0
        Maximum observed diff delay 0ms, least delayed link 2
        Running seconds 9273
        GTSM last changed 03:49:15 UTC Mon Mar 1 1993
    IMA Group Current Counters (time elapsed 870 seconds):
        0 Ne Failures, 0 Fe Failures, 0 Unavail Secs
    IMA Group Interval(1) Counters:
        0 Ne Failures, 0 Fe Failures, 0 Unavail Secs
    IMA Group Interval(2) Counters:
        0 Ne Failures, 0 Fe Failures, 0 Unavail Secs
    IMA Group Interval(3) Counters:
        0 Ne Failures, 0 Fe Failures, 0 Unavail Secs
    IMA Group Interval(4) Counters:
        1 Ne Failures, 1 Fe Failures, 900 Unavail Secs
    IMA Group Interval(5) Counters:
        0 Ne Failures, 0 Fe Failures, 900 Unavail Secs
    IMA Group Interval(6) Counters:
        0 Ne Failures, 0 Fe Failures, 900 Unavail Secs
    IMA Group Interval(7) Counters:
        1 Ne Failures, 0 Fe Failures, 900 Unavail Secs
    IMA Group Total Counters (last 8 15 minute intervals):
        3 Ne Failures, 2 Fe Failures, 3604 Unavail Secs
    Detailed IMA link Information:

Interface ATM0/0 is up
        ifIndex 1, Group Index 1, Row Status is active
        Tx/Rx Lid 0/0, relative delay 0ms
        Ne Tx/Rx state active/active
        Fe Tx/Rx state active/active
        Ne Rx failure status is noFailure
        Fe Rx failure status is noFailure
       Rx test pattern 0x43, test procedure disabled
    IMA Link Current Counters (time elapsed 61 seconds):
        0 Ima Violations, 0 Oif Anomalies
        0 Ne Severely Err Secs, 0 Fe Severely Err Secs
        0 Ne Unavail Secs, 0 Fe Unavail Secs
        0 Ne Tx Unusable Secs, 0 Ne Rx Unusable Secs
        0 Fe Tx Unusable Secs, 0 Fe Rx Unusable Secs
        0 Ne Tx Failures, 0 Ne Rx Failures
        0 Fe Tx Failures, 0 Fe Rx Failures
    IMA Link Interval(1) Counters: 
        0 Ima Violations, 0 Oif Anomalies
        0 Ne Severely Err Secs, 0 Fe Severely Err Secs
        0 Ne Unavail Secs, 0 Fe Unavail Secs
        0 Ne Tx Unusable Secs, 0 Ne Rx Unusable Secs
        0 Fe Tx Unusable Secs, 0 Fe Rx Unusable Secs
        0 Ne Tx Failures, 0 Ne Rx Failures
        0 Fe Tx Failures, 0 Fe Rx Failures
    IMA Link Interval(2) Counters: 
        0 Ima Violations, 0 Oif Anomalies
        0 Ne Severely Err Secs, 0 Fe Severely Err Secs
        0 Ne Unavail Secs, 0 Fe Unavail Secs
        0 Ne Tx Unusable Secs, 0 Ne Rx Unusable Secs
        0 Fe Tx Unusable Secs, 0 Fe Rx Unusable Secs
        0 Ne Tx Failures, 0 Ne Rx Failures
        0 Fe Tx Failures, 0 Fe Rx Failures
    IMA Link Interval(3) Counters: 
        0 Ima Violations, 0 Oif Anomalies
        0 Ne Severely Err Secs, 0 Fe Severely Err Secs
        0 Ne Unavail Secs, 0 Fe Unavail Secs
        0 Ne Tx Unusable Secs, 0 Ne Rx Unusable Secs
        0 Fe Tx Unusable Secs, 0 Fe Rx Unusable Secs
        0 Ne Tx Failures, 0 Ne Rx Failures
        0 Fe Tx Failures, 0 Fe Rx Failures
r3620#show cont atm0/ima1
Interface ATM0/IMA1 is up
  Hardware is ATM IMA
LANE client MAC address is 0050.7305.e681
  hwidb=0x62384A14, ds=0x61D6D2E0
  slot 0, unit 1, subunit 1
  rs8234 base 0x3C000000, slave base 0x3C000000
  rs8234 ds 0x61D6D2E0
  SBDs - avail 2048, guaranteed 1, unguaranteed 2047, starved 0
 Seg VCC table 3C00B800, Shadow Seg VCC Table 61D89928, VCD Table 61D9F954
 Schedule table 3C016800, Shadow Schedule table 61DA5980, Size C7E
 RSM VCC Table 3C03EA80, Shadow RSM VCC Table 61DABC80
 VPI Index Table 3C03C000, VCI Index Table 3C03E680
 Bucket2 Table 3C026200, Shadow Bucket2 Table 61DA8BA4
 MCR Limit Table 3C026600, Shadow MCR Table 61DAA7D0
 ABR template 3C026800, Shadow template 61A738E0
 RM Cell RS Queue 3C03C680
 Queue           TXQ Addr  Pos  StQ Addr  Pos
 0  UBR CHN0     3C038800  0    039184A0  0  
 1  UBR CHN1     3C038C00  0    03918CA0  0  
 2  UBR CHN2     3C039000  0    039194A0  0  

 3  UBR CHN3     3C039400  237  03919CA0  237
 4  VBR/ABR CHN0 3C039800  0    0391A4A0  0  
 5  VBR/ABR CHN1 3C039C00  0    0391ACA0  0  
 6  VBR/ABR CHN2 3C03A000  0    0391B4A0  0  
 7  VBR/ABR CHN3 3C03A400  0    0391BCA0  0  
 8  VBR-RT CHN0  3C03A800  0    0391C4A0  0  
 9  VBR-RT CHN1  3C03AC00  0    0391CCA0  0  
 10 VBR-RT CHN2  3C03B000  0    0391D4A0  0  
 11 VBR-RT CHN3  3C03B400  0    0391DCA0  0  
 12 SIG          3C03B800  0    0391E4A0  0  
 13 VPD          3C03BC00  0    0391ECA0  0  

 Queue           FBQ Addr  Pos  RSQ Addr  Pos
 0  OAM          3C0FEA80  181  0391F560  182
 1  UBR CHN0     3C0FFA80  0    03920560  0  
 2  UBR CHN1     3C100A80  0    03921560  0  
 3  UBR CHN2     3C101A80  0    03922560  0  
 4  UBR CHN3     3C102A80  40   03923560  41 
 5  VBR/ABR CHN0 3C103A80  0    03924560  0  
 6  VBR/ABR CHN1 3C104A80  0    03925560  0  
 7  VBR/ABR CHN2 3C105A80  0    03926560  0  
 8  VBR/ABR CHN3 3C106A80  0    03927560  0  
 9  VBR-RT CHN0  3C107A80  0    03928560  0  
 10 VBR-RT CHN1  3C108A80  0    03929560  0  
 11 VBR-RT CHN2  3C109A80  0    0392A560  0  
 12 VBR-RT CHN3  3C10AA80  0    0392B560  0  
 13 SIG          3C10BA80  0    0392C560  0  
SAR Scheduling channels:  3 3 3 3 -1 -1 -1 -1
ATM channel number is 3
link members are 0xF, active links are 0xF
Group status is noFailure, 4 links configured,
Group Info: Configured links bitmap 0xF, Active links bitmap 0xF,
    Tx/Rx IMA_id 0x1/0x0,
    NE Group status is operational,
    frame length 0x80, Max Diff Delay 0,
    1 min links, clock mode ctc, symmetry symmetricOperation, trl 0, 
    Group Failure status is noFailure.
    Test pattern procedure is disabled
SAR counter totals across all links and groups:
   603 cells output, 0 cells stripped
   560 cells input, 17573739 cells discarded, 0 AAL5 frames discarded
   0 pci bus err, 0 dma fifo full err, 0 rsm parity err
   0 rsm syn err, 0 rsm/seg q full err, 0 rsm overflow err
   0 hs q full err, 0 no free buff q err, 0 seg underflow err
   0 host seg stat q full err

MGX 8220 AUSM-8T1/B

Command summary:

a1.1.10.AUSMB8.a > version

        ***** Cisco Systems, Inc. AXIS AUSM-8T1/E1 Card *****
    Firmware Version    = 5.0.12
    Backup Boot version = AU8_BT_1.0.02
    AUSM8p Xilinx file = ausm8pXilinx.h
VxWorks (for Cisco Systems, Inc.) version 5.1.1-R3000.
Kernel: WIND version 2.4.
Made on Wed Jun 21 18:24:45 PDT 2000.
Boot line:
a1.1.10.AUSMB8.a > dspfeature

  Channelized:  Off
  Rate Control:  On
  IMA feature:  On
a1.1.10.AUSMB8.a > dsplns

  Line  Conn      Type     Status/Coding      Length     XmtClock Alarm Stats
        Type                                             Source         Alarm
  ----  ----- ------------ ------ -------- ------------- -------- ----- -----
  10.1  RJ-48 dsx1ESF         Ena/dsx1B8ZS 0-131 ft      LocalTim  No    No 
  10.2  RJ-48 dsx1ESF         Ena/dsx1B8ZS 0-131 ft      LocalTim  No    No 
  10.3  RJ-48 dsx1ESF         Ena/dsx1B8ZS 0-131 ft      LocalTim  No    No 
  10.4  RJ-48 dsx1ESF         Ena/dsx1B8ZS 0-131 ft      LocalTim  No    No 
  10.5  RJ-48 dsx1ESF         Dis/dsx1B8ZS 0-131 ft      LocalTim           
  10.6  RJ-48 dsx1ESF         Dis/dsx1B8ZS 0-131 ft      LocalTim           
  10.7  RJ-48 dsx1ESF         Dis/dsx1B8ZS 0-131 ft      LocalTim           
  10.8  RJ-48 dsx1ESF         Dis/dsx1B8ZS 0-131 ft      LocalTim           

  LineNumOfValidEntries: 8
a1.1.10.AUSMB8.a > dspln 1

  LineNum:                   1
  LineConnectorType:         RJ-48
  LineType:                  dsx1ESF
  LineEnable:                Enabled
  LineCoding:                dsx1B8ZS
  LineLength:                0-131 ft
  LineXmtClockSource:        LocalTiming
  LineLoopbackCommand:       NoLoop
  LineSendCode:              NoCode
  LineUsedTimeslotsBitMap:   0xffffffff
  LineLoopbackCodeDetection: codeDetectDisabled
  LineBERTEnable:            Disable

  LineNumOfValidEntries: 8
a1.1.10.AUSMB8.a > dspports

No ATM T1/E1 UNI ports currently active

 List of IMA groups:
 ===================

ImaGrp PortType  Conf  Avail  Lines configured  Lines present   Tol Diff  Port e
                 rate   rate                                    Delay(ms)       
------ -------- -----  ------  ---------------  --------------- --------- ------
 10.1   UNI     14364  14364  1.2.3.4          1.2.3.4          275      B/w chd

  NextPortNumAvailable:  8
a1.1.10.AUSMB8.a > dspimagrp 1

   IMA Group number                 : 1
   Port type                        : UNI
   Lines configured                 : 1.2.3.4
   Enable                           : Enabled
   IMA Port state                   : B/w changed
   IMA Group Ne state               : operational
   PortSpeed (cells/sec)            : 14364
   GroupTxAvailCellRate (cells/sec) : 14364
   ImaGroupTxFrameLength(cells)     : 128
   LcpDelayTolerance (IMA frames)   : 1
   ReadPtrWrPtrDiff  (cells)        : 4
   Minimum number of links          : 1
   MaxTolerableDiffDelay (msec)     : 275
   Lines Present                    : 1.2.3.4
   Observed Diff delay (msec)       : 0
   Clock Mode                       : CTC
   GroupAlpha                       : 2
   GroupBeta                        : 2
   GroupGamma                       : 1
   GroupConfiguration               : 1
   IMAGrp Failure status            : No Failure
   Timing reference link            : 1
   ImaGroupTxImaId                  : 0x0
   ExpectedGroupRxImaId             : 0x1   
a1.1.10.AUSMB8.a > dspimainfo

Link  Group    NeTx        NeRx      FeTx         FeRx    TxLID  RxID 
              State       State     State        State                    
------------------------------------------------------------------    
   1   1   Active       Active       Active       Active       0   0
   2   1   Active       Active       Active       Active       1   1
   3   1   Active       Active       Active       Active       2   2
   4   1   Active       Active       Active       Active       3   3
a1.1.10.AUSMB8.a > dspplpp 1

  PhysicalPortNumber:            1
  CellFraming:                   ATM
  CellScramble:                  No Scramble
  Plpp Loopback:                 No Loopback
  Single-bit error correction:   Disabled
a1.1.10.AUSMB8.a > dspimagrpcnt 1

  IMA Group number:                           1
  Ne Number of failures                   :   0
a1.1.10.AUSMB8.a > dspimalncnt 1 1  

   IMA group number                : 1
   Line number                     : 1
   Icp Cells Received              : 140041
   Icp Errored Cells Recvd         : 10
   Ima Violations Count            : 10
   Ima OIF anomalies               : 0
   Ima Ne Severely Errored Seconds : 0
   Ima Fe Severely Errored Seconds : 1
   Ima Ne Unavailable Seconds      : 0
   Ima Fe Unavailable Seconds      : 0
   Ima NeTx Unusable Seconds       : 1336
   Ima NeRx Unusable Seconds       : 1335
   Ima FeTx Unusable Seconds       : 1
   Ima FeRx Unusable Seconds       : 1
   Ima FeTx Num. Failues           : 0
   Ima FeRx Num. Failures          : 0
   # HEC errored cells             : 0
   # HEC errored seconds           : 0
   # Severely HEC errored seconds  : 0
a1.1.10.AUSMB8.a > dspimaln 1 1 

   IMA Group number                 : 1
   Link number                      : 1
   ImaLink TxLId                    : 0x0
   ImaLink RxLId                    : 0x0
   LinkNeRxState                    : Active
   LinkNeTxState                    : Active
   LinkNeRxFailureStatus            : No Failure
   LinkFeRxState                    : Active
   LinkFeTxState                    : Active
   LinkFeRxFailureStatus            : No Failure
   LinkRelDelay                     : 0
   LinkRxTestPattern                : 255
   Ne Link Tx Num Failures          : 0
   Ne Link Rx Num Failures          : 0
a1.1.10.AUSMB8.a > dspchans

Chan Port.VPI.VCI  ConnType Service Type   PCR[0+1]  Q-Depth State  
---- ------------  -------  ------------  ---------  ------- -------
200  1.10.20          VCC     VBR             10      1000   Active

  ChanNumNextAvailable     :  18
  Local VpId NextAvailable :  16
a1.1.10.AUSMB8.a > tstcon 200

tstcon in progress

Test passed.

r3620#ping 2.2.2.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
a1.1.10.AUSMB8.a > dspchan 200

  ChanNum:                           200
  RowStatus:                         Mod
  ConnectionType:                    VCC
  ServiceType:                       VBR
  PortNum:                           1
  VPI:                               10
  VCI (For VCC):                     20
  Local VPId(for VPC):               0
  EgressQNum:                        3
  IngressQDepth(cells):              1000
  IngressDiscardOption:              CLP hysterisis
  IngressFrameDiscardThreshold       1000
  IngressQCLPHigh(cells):            900
  IngressQCLPLow(cells):             800
  QCLPState:                         LOW
  IngressEfciThreshold(cells):       1000

  UPCEnable:                         Enabled
  PeakCellRate[0+1](cells/sec):      50       
  
!--- PINGs set at port speed are discarded.

  CellDelayVariation[0+1]:           10000 (micro secs)
  PeakCellRate[0](cells/sec):        14364
  CellDelayVariation[0]:             250000 (micro secs)
  SustainedCellRate(cells/sec):      50  
  
!--- PINGs set at port speed are discarded.

  MaximumBurstSize(cells):           1000
  SCRPolicing:                       CLP[0]
  CLPTagEnable:                      Enabled
  FrameGCRAEnable:                   Disable

  ForesightEnable:                   Disable
  InitialBurstSize(cells):           0
  ForeSightPeakCellRate(cells/sec):  50
  MinimumCellRate(cells/sec):        50
  InitialCellRate(cells/sec):        50

  LocalRemoteLpbkState:              Disable
  ChanTestType:                      No Test
  ChanTestState:                     Passed
  ChanRTDresult:                     1 ms

  Ingress percentage util:           100
  Egress percentage util :           100
  Egress Service Rate:               50
  ChanOvrSubOvrRide:                 Enabled
  ChanNumNextAvailable     :  17
  Local VpId NextAvailable :  6

r3620#ping 2.2.2.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)

After cnfupcvbr command is used to increase connection parameter:

a1.1.10.AUSMB8.a > dspchan 200

  ChanNum:                           200
  RowStatus:                         Mod
  ConnectionType:                    VCC
  ServiceType:                       VBR
  PortNum:                           1
  VPI:                               10
  VCI (For VCC):                     20
  Local VPId(for VPC):               0
  EgressQNum:                        3
  IngressQDepth(cells):              1000
  IngressDiscardOption:              CLP hysterisis
  IngressFrameDiscardThreshold       1000
  IngressQCLPHigh(cells):            900
  IngressQCLPLow(cells):             800
  QCLPState:                         LOW
  IngressEfciThreshold(cells):       1000

  UPCEnable:                         Enabled
  PeakCellRate[0+1](cells/sec):      3622                    
  CellDelayVariation[0+1]:           25000 (micro secs)
  PeakCellRate[0](cells/sec):        14364
  CellDelayVariation[0]:             250000 (micro secs)
  SustainedCellRate(cells/sec):      2048  
  MaximumBurstSize(cells):           1000
  SCRPolicing:                       CLP[0]
  CLPTagEnable:                      Enabled
  FrameGCRAEnable:                   Disable

  ForesightEnable:                   Disable
  InitialBurstSize(cells):           0
  ForeSightPeakCellRate(cells/sec):  3622    
  MinimumCellRate(cells/sec):        3622    
  InitialCellRate(cells/sec):        3622    

  LocalRemoteLpbkState:              Disable
  ChanTestType:                      No Test
  ChanTestState:                     Passed
  ChanRTDresult:                     1 ms

  Ingress percentage util:           100
  Egress percentage util :           100
  Egress Service Rate:               2633    
  ChanOvrSubOvrRide:                 Enabled

  ChanNumNextAvailable     :  17
  Local VpId NextAvailable :  16

r3620#ping 2.2.2.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 8/13/28 ms

MC 3810

Command summary:

r3a#ping 2.2.2.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2.2.2.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 104/134/144 ms

r3a#show version
Cisco Internetwork Operating System Software 
IOS (tm) MC3810 Software (MC3810-JS-M), Version 12.0(4)T,  RELEASE SOFTWARE (fc)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Wed 28-Apr-99 21:19 by kpma
Image text-base: 0x00023000, data-base: 0x00AF1324

ROM: System Bootstrap, Version 11.3(1)MA1, MAINTENANCE INTERIM SOFTWARE
ROM: MC3810 Software (MC3810-WBOOT-M), Version 11.3(1)MA1,  MAINTENANCE INTERIM 

r3a uptime is 2 hours, 51 minutes
System restarted by reload
System image file is "flash:mc3810-js-mz.120-4.T.bin"

Cisco MC3810 (MPC860) processor (revision 06.07) with 27648K/5120K bytes of mem.
Processor board ID 09550018
PPC860 PowerQUICC, partnum 0x0000, version A03(0x0013)
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
Primary Rate ISDN software, Version 1.1.
MC3810 SCB board (v05.A0)
1 Multiflex T1(slot 3) RJ45 interface(v01.K0)
1 Six-Slot Analog Voice Module (v03.K0)
1    Analog FXS voice interface (v03.K0) port 1/1
1 3-DSP(slot2) Voice Compression Module(v01.--)
1 Ethernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
2 Serial(sync/async) network interface(s)
1 Channelized E1/PRI port(s)
1 Channelized T1/PRI port(s)
256K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (INTEL28F016) 

Configuration register is 0x2102
r3a#show run
Building configuration...

Current configuration:
!
version 12.0
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname r3a
enable password 7 016E2C
!
enable password
!
network-clock base-rate 56k
ip subnet-zero
no ip domain-lookup
!
!
!
controller T1 0
 framing esf
 linecode b8zs
 channel-group 0 timeslots 1-24 speed 64
!
interface Ethernet0
 ip address 172.16.150.53 255.255.255.0
 no ip directed-broadcast
!
interface Serial0
 no ip address
 no ip directed-broadcast
 no ip mroute-cache
 shutdown
 no fair-queue
!
interface Serial1
 no ip address
 no ip directed-broadcast
 shutdown
!
interface Serial0:0
 ip address 2.2.2.2 255.255.255.0
 no ip directed-broadcast
 encapsulation frame-relay IETF
 ip mroute-cache
 frame-relay map ip 2.2.2.1 100 broadcast
!
interface Switch0
 no ip address
 no ip directed-broadcast
 encapsulation frame-relay
 no fair-queue
!
ip classless
ip route 0.0.0.0 0.0.0.0 172.16.150.1
no ip http server
!
!
!
line con 0
 transport input none
line aux 0
line 2 3
line vty 0 4
 exec-timeout 0 0
 password 7 0236C1C
 login
!
!
voice-port 1/1
 timeouts call-disconnect 0
!
!
end
r3a#show fr pvc

PVC Statistics for interface Serial0:0 (Frame Relay DTE)

              Active     Inactive      Deleted       Static
  Local          1            0            0            0
  Switched       0            0            0            0
  Unused         0            0            0            0

DLCI = 100, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0:0

  input pkts 140           output pkts 161          in bytes 104560    
  out bytes 106700         dropped pkts 0           in FECN pkts 0         
  in BECN pkts 0           out FECN pkts 0          out BECN pkts 0         
  in DE pkts 0             out DE pkts 0         
  out bcast pkts 0          out bcast bytes 0         
  pvc create time 02:42:19, last time pvc status changed 01:30:06

PVC Statistics for interface Switch0 (Frame Relay DTE)
r3a#show contr t1 0
T1 0 is up.
  Applique type is Channelized T1
  Cablelength is long gain36 0db
  No alarms detected.
  Slot 3 CSU Serial #08625843 Model TEB HWVersion 4.70 RX level = -0DB
  Framing is ESF, Line Code is B8ZS, Clock Source is Line.
  Data in current interval (567 seconds elapsed):
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
  Data in Interval 1:
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
  Data in Interval 2:
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
  Data in Interval 3:
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
  Data in Interval 4:
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
  Data in Interval 5:
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
  Data in Interval 6:
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
  Data in Interval 7:
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
  Data in Interval 8:
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
  Data in Interval 9:
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
  Data in Interval 8:
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
  Data in Interval 9:
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
  Data in Interval 10:
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
  Data in Interval 11:
     7 Line Code Violations, 0 Path Code Violations
     2 Slip Secs, 0 Fr Loss Secs, 2 Line Err Secs, 0 Degraded Mins
     1 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 866 Unavail Secs
  Total Data (last 11 15 minute intervals):
     7 Line Code Violations, 0 Path Code Violations,
     2 Slip Secs, 0 Fr Loss Secs, 2 Line Err Secs, 0 Degraded Mins,
     1 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 866 Unavail Secs
r3a#show interface s0:0
Serial0:0 is up, line protocol is up 
  Hardware is PQUICC Serial
  Internet address is 2.2.2.2/24
  MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, 
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation FRAME-RELAY IETF, crc 16, loopback not set
  Keepalive set (10 sec)
  Scramble enabled 
  LMI enq sent  964, LMI stat recvd 966, LMI upd recvd 2, DTE LMI up
  LMI enq recvd 0, LMI stat sent  0, LMI upd sent  0
  LMI DLCI 1023  LMI type is CISCO  frame relay DTE
  FR SVC disabled, LAPF state down
  Broadcast queue 0/64, broadcasts sent/dropped 0/0, interface broadcasts 0
  Last input 00:00:04, output 00:00:04, output hang never
  Last clearing of "show interface" counters 02:45:12
  Input queue: 0/75/0 (size/max/drops); Total output drops: 0
  Queueing strategy: weighted fair
  Output queue: 0/1000/64/0 (size/max total/threshold/drops) 
     Conversations  0/1/256 (active/max active/max total)
     Reserved Conversations 0/0 (allocated/max allocated)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     1108 packets input, 118434 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     1133 packets output, 119338 bytes, 0 underruns
     0 output errors, 0 collisions, 2 interface resets
     0 output buffer failures, 0 output buffers swapped out
     0 carrier transitions

Note: Because the debug commands generate a significant amount of output, use them only when traffic on the IP network is low, so other activity on the system is not adversely affected.

r3a#debug frame-relay lmi
Frame Relay LMI debugging is on
Displaying all Frame Relay LMI data
r3a#terminal monitor
% Console already monitors
r3a#
02:59:35: Serial0:0(out): StEnq, myseq 206, yourseen 53, DTE up
02:59:35: datagramstart = 0x1C98A18, datagramsize = 13
02:59:35: FR encap = 0xFCF10309
02:59:35: 00 75 01 01 01 03 02 CE 35 
02:59:35: 
02:59:35: Serial0:0(in): Status, myseq 206
02:59:35: RT IE 1, length 1, type 1
02:59:35: KA IE 3, length 2, yourseq 54, myseq 206
r3a#
02:59:45: Serial0:0(out): StEnq, myseq 207, yourseen 54, DTE up
02:59:45: datagramstart = 0x1C98A18, datagramsize = 13
02:59:45: FR encap = 0xFCF10309
02:59:45: 00 75 01 01 01 03 02 CF 36 
02:59:45: 
02:59:45: Serial0:0(in): Status, myseq 207
02:59:45: RT IE 1, length 1, type 1
02:59:45: KA IE 3, length 2, yourseq 55, myseq 207

MGX 8220 FRSM-8T1

Command summary:

a1.1.9.FRSM.a > version
***** Cisco Systems, Inc. AXIS FRSM-8P Card *****
    Firmware Version    = 5.0.13
    Backup Boot version = FR8_BT_1.0.02
    ASCFRSM Xilinx file = cbslave.h
VxWorks (for Cisco Systems, Inc.) version 5.2 Rev B.
Kernel: WIND version 2.4.
Made on Wed Jun 21 16:15:40 PDT 2000.
Boot line:
a1.1.9.FRSM.a > dspfeature

  Channelized:  On
  Rate Control:  On
a1.1.9.FRSM.a > dsplns

  Line  Conn      Type     Status/Coding      Length     XmtClock Alarm Stats
        Type                                             Source         Alarm
  ----  ----- ------------ ------ -------- ------------- -------- ----- -----
  9.1   RJ-48 dsx1ESF         Ena/dsx1B8ZS 0-131 ft      LocalTim  No    No 
  9.2   RJ-48 dsx1ESF         Dis/dsx1B8ZS 0-131 ft      LocalTim           
  9.3   RJ-48 dsx1ESF         Dis/dsx1B8ZS 0-131 ft      LocalTim           
  9.4   RJ-48 dsx1ESF         Dis/dsx1B8ZS 0-131 ft      LocalTim           
  9.5   RJ-48 dsx1ESF         Dis/dsx1B8ZS 0-131 ft      LocalTim           
  9.6   RJ-48 dsx1ESF         Dis/dsx1B8ZS 0-131 ft      LocalTim           
  9.7   RJ-48 dsx1ESF         Dis/dsx1B8ZS 0-131 ft      LocalTim           
  9.8   RJ-48 dsx1ESF         Dis/dsx1B8ZS 0-131 ft      LocalTim           

  LineNumOfValidEntries: 8
a1.1.9.FRSM.a > dspln 1

  LineNum:                   1
  LineConnectorType:         RJ-48
  LineType:                  dsx1ESF
  LineEnable:                Enabled
  LineCoding:                dsx1B8ZS
  LineLength:                0-131 ft
  LineXmtClockSource:        LocalTiming
  LineLoopbackCommand:       NoLoop
  LineSendCode:              NoCode
  LineUsedTimeslotsBitMap:   0xffffff
  LineLoopbackCodeDetection: codeDetectDisabled
  LineBertEnable:            Disable

  LineNumOfValidEntries: 8
a1.1.9.FRSM.a > dspports

    Port   Ena/Speed EQServ  SignalType  T391 T392 N391 N392 N393   Type   AlarI
                     Ratio
  -------- --- ----- ------ ------------ ---- ---- ---- ---- ---- -------- -----
  9.1.1    Mod/1536k   1    StrataLMI      10   15    6    3    4 frameRel  No  

  Number of ports:              1

  PortDs0UsedLine1:             0x00ffffff
  PortDs0UsedLine2:             0x00000000
  PortDs0UsedLine3:             0x00000000
  PortDs0UsedLine4:             0x00000000
  PortDs0UsedLine5:             0x00000000
  PortDs0UsedLine6:             0x00000000
  PortDs0UsedLine7:             0x00000000
  PortDs0UsedLine8:             0x00000000
  PortNumNextAvailable:         155
a1.1.9.FRSM.a > dspport 1

  SlotNum:                      9
  PortLineNum:                  1
  PortNum:                      1
  PortRowStatus:                Mod
  PortDs0Speed:                 64k
  PortDs0ConfigBitMap(1stDS0):  0xffffff(1)
  PortEqueueServiceRatio:       1
  PortFlagsBetweenFrames:       1
  PortSpeed:                    1536kbps
  SignallingProtocolType:       StrataLMI
  AsynchronousMsgs:             UPD enabled
  T391LineIntegrityTimer:       10
  T392PollingVerificationTimer: 15
  N391FullStatusPollingCounter: 6
  N392ErrorThreshold:           3
  N393MonitoredEventCount:      4
  EnhancedLmi:                  On
  PortState:                    Active
  PortSignallingState:          No Signalling Failure
  CLLMEnableStatus:             Disable
  CLLMxmtStatusTimer:           0
  portType:                     frameRelay
  PortIngrPercentUtil:          100
  PortEgrPercentUtil:           100
  PortOversubscribed:           False
  PortSvcStatus:                Disable
  PortSvcInUse:                 Not In-Use
  PortSvcShareLcn:              Card-based
  PortSvcLcnLow:                0
  PortSvcLcnHigh:               0
  PortSvcDlciLow:               0
  PortSvcDlciHigh:              0

  PortDs0UsedLine1:             0x00ffffff
  PortDs0UsedLine2:             0x00000000
  PortDs0UsedLine3:             0x00000000
  PortDs0UsedLine4:             0x00000000
  PortDs0UsedLine5:             0x00000000
  PortDs0UsedLine6:             0x00000000
  PortDs0UsedLine7:             0x00000000
  PortDs0UsedLine8:             0x00000000
  PortNumNextAvailable:         164
a1.1.9.FRSM.a > dspchans

      DLCI      Chan EQ  I/EQDepth  I/EQDEThre  I/EECNThre  Fst/ DE Type  Alarm
  ------------- ---- -- ----- ----- ----- ----- ----- ----- --- --- ----- -----
  9.1.1.100     100  2  65535/65535 32767/32767  6553/6553  Dis/Dis SIW-X  No  

  Number of channels:    1

  ChanNumNextAvailable:  44
a1.1.9.FRSM.a > dspchan 100

  ChanNum:                  100
  ChanRowStatus:            Mod
  ChanPortNum:              1
  ChanDLCI:                 100
  EgressQSelect:            2
  IngressQDepth:            65535
  IngressQDEThresh:         32767
  IngressQECNThresh:        6553
  EgressQDepth:             65535
  EgressQDEThresh:          32767
  EgressQECNThresh:         6553
  DETaggingEnable:          Disabled
  CIR:                      1536000
  Bc:                       5100
  Be:                       5100
  IBS:                      100
  ForeSightEnable:          Disabled
  QIR:                      4000
  MIR:                      4000
  PIR:                      4000
  ChanLocalRemoteLpbkState: Disabled
  ChanTestType:             TestOff
  ChanTestState:            Passed
  ChanRTDresult:            1 ms
  ChanType:                 SIW-Xlat    
  ChanFECNmap:              setEFCIzero
  ChanDEtoCLPmap:           mapCLP    
  ChanCLPtoDEmap:           mapDE    
  ChanFrConnType:           PVC
  ChanIngrPercentUtil:      100
  ChanEgrPercentUtil:       100
  ChanEgrSrvRate:           1536000
  ChanOvrSubOvrRide:        Enabled

  ChanNumNextAvailable:  45
a1.1.9.FRSM.a > tstcon 100

TestCon in progress.

TestCon Passed.

BPX 8600

Command summary:

b3             TRM   SuperUser       BPX 8600  9.1.18    Sep. 22 2000 17:08 GMT 


   FrontCard    BackCard                    FrontCard    BackCard
   Type    Rev  Type  Rev   Status          Type    Rev  Type  Rev   Status
1  Empty                                 9  BXM-155 CDB  MM-4  BA    Standby-T
2  BNI-T3  CJM  T3-3  BE    Active       10 BXM-155 EJB  MM-4  BA    Standby
3  BNI155E DJR  Empty       Standby      11 BNI155E DJR  MMF-2 AC    Standby
4  Empty                                 12 Empty                               
5  BXM-T3  CDE  TE3-12BA    Standby      13 BXM-T3  BDY  TE3-12BA    Standby
6  ASI-T3  CDF  T3-2  BE    Standby      14 Empty                               
7  BCC-3   CLM  LM-2  AC    Active       15 ASM     ACC  LMASM AC    Active
8  BCC-3   CLM  LM-2  AC    Standby     
                                                                                
Last Command: dspcds
b3             TRM   SuperUser       BPX 8600  9.1.18    Sep. 22 2000 17:08 GMT 


                   BPX 8600 Interface Shelf Information

Trunk    Name      Type          Part Id   Ctrl Id   Alarm
 2.1     a1        AXIS             -         -      MIN

                                                                                
Last Command: dspnode
b3             TRM   SuperUser       BPX 8600  9.1.18    Sep. 22 2000 17:09 GMT 


TRK     Type     Current Line Alarm Status               Other End
 2.1    T3       Clear - OK                              a1(AXIS)
                                                                                
Last Command: dsptrks
b3             TRM   SuperUser       BPX 8600  9.1.18    Sep. 22 2000 17:09 GMT 


TRK  2.1 Config    T3      [96000 cps]     BNI-T3 slot:  2                      
Transmit Rate:         96000               VPC Conns disabled:    --           
Subrate data rate:     --                  Line framing:          PLCP         
Line DS-0 map:         --                       coding:           --           
Statistical Reserve:   1000    cps              recv impedance:   --           
Idle code:             7F hex                   cable type:                    
Max Channels/Port:     --                             length:     0-225 ft.    
Connection Channels:   2027                Pass sync:             Yes          
Traffic:   V,TS,NTS,FR,FST,CBR,VBR,ABR     Loop clock:            No           
SVC Vpi Min:           --                  HCS Masking:           Yes          
SVC Channels:          --                  Payload Scramble:      No           
SVC Bandwidth:         --     cps          Frame Scramble:        --           
Restrict CC traffic:   No                  Virtual Trunk Type:    --           
Link type:             Terrestrial         Virtual Trunk VPI:     --           
Routing Cost:          10                  Deroute delay time:    0 seconds    
                                                                                
Last Command: dsptrkcnf 2.1
b3             TRM   SuperUser       BPX 8600  9.1.18    Sep. 22 2000 17:09 GMT 


 Local           Remote      Remote                             Route
 Channel         NodeName    Channel         State  Type        Avoid COS O
 2.1.9.100       b3          2.1.10.200      Ok     atfr
 2.1.10.200      b3          2.1.9.100       Ok     atfr
                                                                                
Last Command: dspcons
b3             TRM   SuperUser       BPX 8600  9.1.18    Sep. 22 2000 17:09 GMT 


Conn:  2.1.9.100        b3          2.1.10.200        atfr      Status:OK
    PCR(0+1)    % Util    CDVT(0+1)    FBTC       SCR           MBS     PLC
   2000/2000   100/100   25000/25000    y      1000/1000     1000/1000    3


Path:   Route information not applicable for local connections


b3            BNI-T3    : OK           b3        BNI-T3    : OK
              Line  2.1 : OK                     Line  2.1 : OK
              OAM Cell RX: Clear                 NNI       : OK
              NNI       : OK
                                                                                
Conn:  2.1.9.100        b3          2.1.10.200        atfr      Status:OK
   PCR(0+1)        % Util       CDVT(0+1)            SCR               MBS     
 2000/2000        100/100      25000/25000       1000/1000         1000/1000

Policing    VC Qdepth     EFCI         IBS     
    3      1280/1280     35/35        1/1
                                                                                
Last Command: dspcon 2.1.9.100
b3             TRM   SuperUser       BPX 8600  9.1.18    Sep. 22 2000 17:13 GMT 


 Local           Remote      Remote                             Route
 Channel         NodeName    Channel         State  Type        Avoid COS O
 2.1.9.100       b3          2.1.10.200      Ok     atfr
 2.1.10.200      b3          2.1.9.100       Ok     atfr
                                                                                
This Command: dspchstats 2.1.10.200

Channel stats is not supported
Enter channel: 
b3             TRM   SuperUser       BPX 8600  9.1.18    Sep. 22 2000 17:10 GMT 


Conn:  2.1.9.100        b3          2.1.10.200        atfr      Status:OK
   PCR(0+1)        % Util       CDVT(0+1)            SCR               MBS     
 2000/2000        100/100      25000/25000       1000/1000         1000/1000

Policing    VC Qdepth     EFCI         IBS     
    3      1280/1280     35/35        1/1
                                                                                
This Command: tstconseg 2.1.9.100

Not allowed on feeder trunk endpoints
Channel: 
!-- When no corresponding connection exists on the FRSM or AUSM:


b3             TRM   SuperUser       BPX 8600  9.1.18    Sep. 22 2000 21:46 GMT 

Alarm summary   (Configured alarm slots: None)
Connections Failed:     None
TRK Alarms:             None
Line Alarms:            None
Cards Failed:           None
Slots Alarmed:          None               Connection A-bit/AIS Alarms: 2
Missing Cards:          None
Remote Node Alarms:     None


Interface Shelf Alarms: 1 Minor
ASM Alarms:             None

                                                                                
Last Command: dspalms
b3             TRM   SuperUser       BPX 8600  9.1.18    Sep. 22 2000 21:46 GMT 


 Local           Remote      Remote                    Local     Remote
 Channel         NodeName    Channel         State      A-bit     A-bit  
 2.1.9.100       b3          2.1.10.200      Ok        Failed    Failed
 2.1.10.200      b3          2.1.9.100       Ok        Failed    Failed

                                                                                
Last Command: dspcons -abit
b3             TRM   SuperUser       BPX 8600  9.1.18    Sep. 22 2000 21:47 GMT 


Conn:  2.1.9.100        b3          2.1.10.200        atfr      Status:OK
    PCR(0+1)    % Util    CDVT(0+1)    FBTC       SCR           MBS     PLC
   2000/2000   100/100   25000/25000    y      1000/1000     1000/1000    3


Path:   Route information not applicable for local connections


b3            BNI-T3    : OK           b3        BNI-T3    : OK
              Line  2.1 : OK                     Line  2.1 : OK
              OAM Cell RX: Clear                 NNI       : Rmt Segment Failure
              NNI       : Rmt Segment Failure
                                                                                
Last Command: dspcon 2.1.9.100


!--- After the frame relay side has been configured on the MGX 8220 FRSM:


b3             TRM   SuperUser       BPX 8600  9.1.18    Sep. 22 2000 21:55 GMT 

Conn:  2.1.9.100        b3          2.1.10.200        atfr      Status:OK
    PCR(0+1)    % Util    CDVT(0+1)    FBTC       SCR           MBS     PLC
   2000/2000   100/100   25000/25000    y      1000/1000     1000/1000    3


Path:   Route information not applicable for local connections


b3            BNI-T3    : OK           b3        BNI-T3    : OK
              Line  2.1 : OK                     Line  2.1 : OK
              OAM Cell RX: Clear                 NNI       : Rmt Segment Failure
              NNI       : OK
                                                                                
Last Command: dspcon 2.1.9.100


!--- When both frame relay and ATM sides have been configured on the MGX 8220 FRSM 
!--- and AUSM:
 

b3             TRM   SuperUser       BPX 8600  9.1.18    Sep. 22 2000 21:58 GMT 


Conn:  2.1.9.100        b3          2.1.10.200        atfr      Status:OK
    PCR(0+1)    % Util    CDVT(0+1)    FBTC       SCR           MBS     PLC
   2000/2000   100/100   25000/25000    y      1000/1000     1000/1000    3


Path:   Route information not applicable for local connections


b3            BNI-T3    : OK           b3        BNI-T3    : OK
              Line  2.1 : OK                     Line  2.1 : OK
              OAM Cell RX: Clear                 NNI       : OK
              NNI       : OK
                                                                                
Last Command: dspcon 2.1.9.100

Related Information

Updated: Oct 23, 2009
Document ID: 22203