Guest

Cisco 1605-R Dual Ethernet/WAN Interface Card Slot Router Cable Specifications

Cisco - Cisco 1605-R Dual Ethernet/WAN Interface Card Slot Router Cable Specifications

Document ID: 46788

Updated: Jul 07, 2005

   Print

Introduction

This document provides the cabling specifications for the Cisco 1605-R Dual Ethernet/WAN Interface Card Slot router.

Prerequisites

Requirements

There are no specific requirements for this document.

Components Used

The information in this document is based on the hardware version:

  • Cisco 1605-R Router

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Conventions

For more information on document conventions, see the Cisco Technical Tips Conventions.

Cabling Specifications

The Cisco 1605-R router has two Ethernet interfaces, and one WAN interface card (WIC) slot.

1605R.gif

The cabling details for the Cisco 1605-R are as follows:

Console

The console cable is an RJ-45, the CAB-1600-CON=.

Ethernet

On the 1605-R router, there are two functional ports for either the 10Base-T (RJ-45) or AUI (DB-15) cables. The cable details are:

  • CAB-ETH-S-RJ45=

  • Yellow Cable for Ethernet

  • Straight-through

  • RJ-45

  • 6 ft.

The AUI adapter cable is a CAB-3CE18=.

WAN Interface Cards

WAN interface cards supported on the Cisco 1605-R consist of the following:

  • WIC-1T: 1-port serial, async and sync (T1/E1)

  • WIC-1DSU-56K4: 1 serial with integrated 56/64 Kbps 4-wire DSU/CSU

  • WIC-1DSU-T1: 1 serial with integrated T1/Fractional T1 DSU/CSU

  • WIC-1B-S/T: 1 ISDN BRI S/T

  • WIC-1B-U: 1 ISDN BRI U with integrated NT-1

Front Panel LEDs

1605led.gif

The table below shows the front panel LED functions for the Cisco 1605 router.

LED Color Description
SYSTEM PWR Green The router is on, and DC power is being supplied.
SYSTEM OK Green The router has successfully booted. Blinks during the boot cycle.
ETH ACT Green Data is being sent to or received from the first Ethernet LAN.
ETH COL Yellow Flashing indicates packet collisions on the first Ethernet LAN.
ETH1 ACT Green Data is being sent to or received from the second Ethernet LAN.
ETH1 COL Yellow Flashing indicates packet collisions on the second Ethernet LAN.
WIC CD/B1 Green Data is being sent to or received from the WAN interface card port.
WIC ACT/B2 Green Data is being sent to or received from the WAN interface card port.

Rear Panel LEDs

The table below explains the rear panel LED functions.

LED Color Description
All Models
LNK (next to ETHERNET 10BASET) Green Indicates 10BaseT link integrity. This LED is not on when connected to an Ethernet network through the AUI port. The Cisco 1605 has two LNK LEDs, one for each Ethernet 10BaseT port.
OK (next to FLASH PC CARD slot) Green The Flash PC card is correctly installed.
Cisco 1601
RDY Green A serial port cable connection has been made to a modem or DSU/CSU.
Cisco 1602
LOOPBACK Yellow The DSU/CSU is in DSU or CSU loopback mode.
ALARM Yellow An alarm condition exists on the DSU/CSU port.
CARRIER Green Indicates line synchronization or connection on the DSU/CSU port.
Cisco 1603
OK (next to ISDN BRI S/T port) Green A physical connection has been established with the ISDN central office switch.
Cisco 1604
NT1 Green A physical connection has been established from the router internal NT1 to the ISDN central office switch.
OK (next to ISDN PHONE port) Green The device connected to the router ISDN S/T port has established a physical connection with the ISDN central office switch.
Cisco 1605
LNK (next to ETHERNET1 10BASET) Green Indicates 10BaseT link integrity for the Ethernet 1 port.
OK (next to WIC slot) Green The WAN interface card is correctly installed in the router.

Related Information

Updated: Jul 07, 2005
Document ID: 46788