Guest

Multiprotocol Label Switching over ATM (MPLS over ATM)

Configuring VPN MPLS over ATM with Cisco 7500 Routers and LightStream 1010 Switches

Document ID: 10533

Updated: Jun 05, 2005

   Print

Introduction

This document shows how to configure Virtual Private Network (VPN) Multiprotocol Label Switching (MPLS) over ATM with Cisco 7500 routers as Label Edge Routers (LERs) and LightStream 1010 switches as Label Switch Routers (LSRs). Two ethernet-connected routers, each on a remote customer site, are part of a VPN. In this document, we look at the end-to-end device configurations and helpful show commands.

Prerequisites

Requirements

There are no specific requirements for this document.

Conventions

Refer to Cisco Technical Tips Conventions for more information on document conventions.

Configure

In this section, you are presented with the information to configure the features described in this document.

Network Diagram

This document uses this network setup:

vpn-mpls-1.gif

Network Description

The current setup contains these elements in VPN terminology:

  • CE = Customer Edge Router

  • PE = Provider Edge Router

  • P=Provider Router

The current setup contains these elements in MPLS terminology:

  • LER = Label Edge Router

  • LSR = Label Switch Router

  • TDP/LDP = Tag Distribution Protocol/Label Distribution Protocol

Configurations

This document uses these configurations:

  • PE1 and PE2 are the LERs in our ATM network.

  • P1 and P2 are the LSRs.

  • CE1 and CE2 are Customer Edge Routers that are unaware and do not carry out VPN or MPLS.

  • CE1 and CE2 are Ethernet connected to PE1 and PE2 respectively, and carry out Routing Information Protocol (RIP).

  • PE1, PE2, P1 and P2 do Open Shortest Path First (OSPF) and are all in Area 0. OSPF is the Interior Gateway Protocol (IGP) used in the ATM network. Tag-switching is used on the ATM interfaces on all four ATM devices. Tag Distribution Protocol (TDP) assigns Tags to the OSPF routes.

  • PE1 and PE2 are Multiprotocol-Border Gateway Protocol (MP-BGP) peers.

  • RIP routes are redistributed into MP-BGP. MP-BGP routes redistributed into RIP on PE1 and PE2 routers.

  • The setup maintains separate VRF routing tables in the PE1 and PE2 routers.

  • The name of the VPN used in this example is NEW.

CE1
! 
version 12.1 
service timestamps debug datetime msec 
service timestamps log datetime msec 

! 
boot system flashow c4500-js-mz.121-5 
! 

ip subnet-zero 

! 
interface Loopback0 
 ip address 10.1.1.1 255.255.255.0 
! 
interface Loopback1 
 ip address 10.2.2.2 255.255.255.0 
! 
interface Loopback2 
 ip address 10.3.3.3 255.255.255.0 
! 
interface Ethernet0 
 ip address 100.1.1.2 255.255.255.0 
 media-type 10BaseT 

! 

router rip 
 version 2 
 network 10.0.0.0 
 network 100.0.0.0 
 no auto-summary 
! 
ip classless 
!

PE1
! 
version 12.1 

service timestamps debug uptime 
service timestamps log uptime 

! 
boot system flashow slot1:rsp-jsv-mz.121-5a.bin 
! 

ip subnet-zero 

! 
ip vrf NEW 
 rd 200:1 
 route-target export 200:1 
 route-target import 200:1 
ip cef distributed 

! 
interface Loopback0 
 ip address 1.1.1.1 255.255.255.255 
! 
interface ATM2/0/0 
 mtu 1500 
 no ip address 
! 
interface ATM2/0/0.10 tag-switching 
 ip unnumbered Loopback0 
 tag-switching ip 
! 
interface Ethernet2/1/0 
 ip vrf forwarding NEW 
 ip address 100.1.1.1 255.255.255.0 

! 
router ospf 100 
 no log-adjacency-changes 
 network 1.0.0.0 0.255.255.255 area 0 
 network 100.1.1.0 0.0.0.255 area 0 
! 
router rip 
 version 2 
 network 100.0.0.0 
 no auto-summary 
 ! 
 address-family ipv4 vrf NEW 
 version 2 
 redistribute bgp 200 metric 0 
 network 100.0.0.0 
 no auto-summary 
 exit-address-family 
! 
router bgp 200 
 bgp log-neighbor-changes 
 neighbor 2.2.2.2 remote-as 200 

 neighbor 2.2.2.2 update-source Loopback0 
 no auto-summary 
 ! 
 address-family ipv4 vrf NEW 
 redistribute rip 
 no auto-summary 
 no synchronization 
 exit-address-family 
 ! 
 address-family vpnv4 
 neighbor 2.2.2.2 activate 
 neighbor 2.2.2.2 send-community extended 
 no auto-summary 
 exit-address-family 
! 
ip classless 
!

P1
!

service timestamps debug uptime 
service timestamps log uptime 
!

ip subnet-zero 
! 

interface Loopback0 
 ip address 4.4.4.4 255.255.255.255 
 no ip directed-broadcast 
! 
interface ATM12/0/0 
 ip unnumbered Loopback0 
 no ip directed-broadcast 

 tag-switching ip 
! 
interface ATM12/0/1 
 ip unnumbered Loopback0 
 no ip directed-broadcast 

 tag-switching ip 

! 
router ospf 100 
 network 4.0.0.0 0.255.255.255 area 0 
! 
ip classless 
! 

P2
! 
service timestamps debug uptime 
service timestamps log uptime 

! 
ip subnet-zero 

! 
interface Loopback0 
 ip address 3.3.3.3 255.255.255.255 
 no ip directed-broadcast 
!  
interface ATM0/1/1 
 ip unnumbered Loopback0 
 no ip directed-broadcast 

 tag-switching ip 
! 
interface ATM0/1/3 
 ip unnumbered Loopback0 
 no ip directed-broadcast 

 tag-switching ip 

! 
router ospf 100 
 network 3.0.0.0 0.255.255.255 area 0 
! 
ip classless 
!

PE2
! 
version 12.1 
service timestamps debug datetime msec 
service timestamps log datetime msec 

! 
boot system flashow slot0:rsp-jsv-mz.121-5a 
! 

ip subnet-zero 

! 
ip vrf NEW 
 rd 200:1 
 route-target export 200:1 
 route-target import 200:1 
ip cef distributed 

! 
interface Loopback0 
 ip address 2.2.2.2 255.255.255.255 
! 

interface FastEthernet3/0/0 
 ip vrf forwarding NEW 
 ip address 110.1.1.1 255.255.255.0 

 half-duplex 
! 

interface ATM3/1/0.1 tag-switching 
 ip unnumbered Loopback0 
 tag-switching ip 
! 
router ospf 100 
 log-adjacency-changes 
 network 2.0.0.0 0.255.255.255 area 0 

! 
router rip 
 version 2 
 network 110.0.0.0 
 no auto-summary 
 ! 
 address-family ipv4 vrf NEW 
 version 2 
 redistribute bgp 200 metric 0 
 network 110.0.0.0 
 no auto-summary 
 exit-address-family 
! 
router bgp 200 
 bgp log-neighbor-changes 
 neighbor 1.1.1.1 remote-as 200 

 neighbor 1.1.1.1 update-source Loopback0 

 no auto-summary 
 ! 
 address-family ipv4 vrf NEW 
 redistribute rip 
 no auto-summary 
 no synchronization 
 exit-address-family 
 ! 
 address-family vpnv4 
 neighbor 1.1.1.1 activate 
 neighbor 1.1.1.1 send-community extended
 no auto-summary 
 exit-address-family 
! 
ip classless 
!

CE2
! 
version 12.1 

service timestamps debug uptime 
service timestamps log uptime 

! 

boot system disk0:c7100-jo3s56i-mz.121-5.T.bin 

! 
ip subnet-zero 

! 
interface Loopback0 
 ip address 30.1.1.1 255.255.255.0 
! 
interface Loopback1 
 ip address 30.2.2.2 255.255.255.0 
! 
interface Loopback2 
 ip address 30.3.3.3 255.255.255.0 
! 
interface FastEthernet0/0 
 ip address 110.1.1.2 255.255.255.0 

! 
router rip 
 version 2 
 network 30.0.0.0 
 network 110.0.0.0 
 no auto-summary 
! 

show Commands

Use these commands to test that your network operates properly:

  • show ip route - Displays IP routing table entries.

  • show ip rip database vrf - Shows information contained in the RIP database for a particular VRF.

  • show ip bgp vpnv4 vrf - Displays VPN address information from the BGP table.

  • show tag-switching interfaces detail - Displays information about one or more interfaces that have the MPLS feature enabled.

  • show tag-switching tdp bindings - Displays the requested entries from the ATM LDP label binding database.

  • show tag-switching forwarding-table vrf - Checks the label stack used for a particular route.

The output shown below is a result of these entered commands on the devices shown in the network diagram. This output shows that the network operates properly.

CE1

Cisco4500#show ip route 
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP 
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP 
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area 
       * - candidate default, U - per-user static route, o - ODR 
       P - periodic downloaded static route 

Gateway of last resort is not set 

     100.0.0.0/24 is subnetted, 1 subnets 
C       100.1.1.0 is directly connected, Ethernet0 
     110.0.0.0/24 is subnetted, 1 subnets 
R       110.1.1.0 [120/1] via 100.1.1.1, 00:00:14, Ethernet0 
     10.0.0.0/24 is subnetted, 3 subnets 
C       10.3.3.0 is directly connected, Loopback2 
C       10.2.2.0 is directly connected, Loopback1 
C       10.1.1.0 is directly connected, Loopback0 
     30.0.0.0/24 is subnetted, 3 subnets 
R       30.3.3.0 [120/1] via 100.1.1.1, 00:00:14, Ethernet0 
R       30.2.2.0 [120/1] via 100.1.1.1, 00:00:15, Ethernet0 
R       30.1.1.0 [120/1] via 100.1.1.1, 00:00:15, Ethernet0 

PE1

Cisco7500a#show ip route 
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP 
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP 
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area 
       * - candidate default, U - per-user static route, o - ODR 
       P - periodic downloaded static route 

Gateway of last resort is not set 

     1.0.0.0/32 is subnetted, 1 subnets 
C       1.1.1.1 is directly connected, Loopback0 
     2.0.0.0/32 is subnetted, 1 subnets 
O       2.2.2.2 [110/4] via 4.4.4.4, 18:17:37, ATM2/0/0.10 
     3.0.0.0/32 is subnetted, 1 subnets 
O       3.3.3.3 [110/3] via 4.4.4.4, 18:17:37, ATM2/0/0.10 
     4.0.0.0/32 is subnetted, 1 subnets 
O       4.4.4.4 [110/2] via 4.4.4.4, 18:17:37, ATM2/0/0.10 

Cisco7500a#show ip route vrf NEW 
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP 
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP 
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area 
       * - candidate default, U - per-user static route, o - ODR 
       P - periodic downloaded static route 

Gateway of last resort is not set 

     100.0.0.0/24 is subnetted, 1 subnets 
C       100.1.1.0 is directly connected, Ethernet2/1/0 
     110.0.0.0/24 is subnetted, 1 subnets 
B       110.1.1.0 [200/0] via 2.2.2.2, 00:26:11 
     10.0.0.0/24 is subnetted, 3 subnets 
R       10.3.3.0 [120/1] via 100.1.1.2, 00:00:11, Ethernet2/1/0 
R       10.2.2.0 [120/1] via 100.1.1.2, 00:00:11, Ethernet2/1/0 
R       10.1.1.0 [120/1] via 100.1.1.2, 00:00:11, Ethernet2/1/0 
     30.0.0.0/24 is subnetted, 3 subnets 
B       30.3.3.0 [200/1] via 2.2.2.2, 00:26:12 
B       30.2.2.0 [200/1] via 2.2.2.2, 00:26:12 
B       30.1.1.0 [200/1] via 2.2.2.2, 00:26:12

Cisco7500a#show ip rip database vrf NEW 
10.0.0.0/8    auto-summary 
10.1.1.0/24 
    [1] via 100.1.1.2, 00:00:18, Ethernet2/1/0 
10.2.2.0/24 
    [1] via 100.1.1.2, 00:00:18, Ethernet2/1/0 
10.3.3.0/24 
    [1] via 100.1.1.2, 00:00:18, Ethernet2/1/0 
30.0.0.0/8    auto-summary 
30.1.1.0/24    redistributed 
    [1] via 2.2.2.2, 
30.2.2.0/24    redistributed 
    [1] via 2.2.2.2, 
30.3.3.0/24    redistributed 
    [1] via 2.2.2.2, 
100.0.0.0/8    auto-summary 
100.1.1.0/24    directly connected, Ethernet2/1/0 
110.0.0.0/8    auto-summary 
110.1.1.0/24    redistributed 
    [1] via 2.2.2.2, 

Cisco7500a#show ip bgp vpnv4 vrf NEW 
BGP table version is 17, local router ID is 1.1.1.1 
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal 
Origin codes: i - IGP, e - EGP, ? - incomplete 

   Network          Next Hop            Metric LocPrf Weight Path 
Route Distinguisher: 200:1 (default for vrf NEW) 
*> 10.1.1.0/24      100.1.1.2                1         32768 ? 
*> 10.2.2.0/24      100.1.1.2                1         32768 ? 
*> 10.3.3.0/24      100.1.1.2                1         32768 ? 
*>i30.1.1.0/24      2.2.2.2                  1    100      0 ? 
*>i30.2.2.0/24      2.2.2.2                  1    100      0 ? 
*>i30.3.3.0/24      2.2.2.2                  1    100      0 ? 
*> 100.1.1.0/24     0.0.0.0                  0         32768 ? 
*>i110.1.1.0/24     2.2.2.2                  0    100      0 ? 

Cisco7500a#show tag-switching interfaces 
Interface              IP    Tunnel   Operational 
ATM2/0/0.10            Yes   No       Yes         (ATM tagging) 

Cisco7500a#show tag-switching interfaces detail 
Interface ATM2/0/0.10: 
        IP tagging enabled 
        TSP Tunnel tagging not enabled 
        Tagging operational 
        Tagswitching turbo vector 
        MTU = 4470 
        ATM tagging: 
                Tag VPI = 1 
                Tag VCI range = 33 - 65535 
                Control VC = 0/32 

Cisco7500a#show tag-switching ? 
  atm-tdp           ATM Tagging Protocol information 
  cos-map           Show Tag CoS ATM Multi-VC CoS Map 
  forwarding-table  Show the Tag Forwarding Information Base (TFIB) 
  interfaces        Show per-interface tag switching 
  prefix-map        Show Tag CoS Prefix Map 
  tdp               Tag Distribution Protocol information 
  
Cisco7500a#show tag-switching tdp bindings 
  tib entry: 1.1.1.1/32, rev 2 
        local binding:  tag: imp-null 
  tib entry: 2.2.2.2/32, rev 23 
        local binding:  tag: 27 
  tib entry: 3.3.3.3/32, rev 21 
        local binding:  tag: 26 
  tib entry: 4.4.4.4/32, rev 10 
        local binding:  tag: 28 

Cisco7500a#show tag-switching atm-tdp bindings 
 Destination: 4.4.4.4/32 
    Headend Router ATM2/0/0.10 (1 hop) 1/33  Active, VCD=24 
 Destination: 3.3.3.3/32 
    Headend Router ATM2/0/0.10 (2 hops) 1/43  Active, VCD=25 
 Destination: 2.2.2.2/32 
    Headend Router ATM2/0/0.10 (3 hops) 1/42  Active, VCD=26 
 Destination: 1.1.1.1/32 
    Tailend Router ATM2/0/0.10 1/33 Active, VCD=24 

Cisco7500a#show tag-switching forwarding-table vrf NEW 
Local  Outgoing    Prefix            Bytes tag  Outgoing   Next Hop 
tag    tag or VC   or Tunnel Id      switched   interface 
29     Aggregate   100.1.1.0/24[V]   2080 
30     Untagged    10.3.3.0/24[V]    0          Et2/1/0    100.1.1.2 
31     Untagged    10.2.2.0/24[V]    0          Et2/1/0    100.1.1.2 
32     Untagged    10.1.1.0/24[V]    0          Et2/1/0    100.1.1.2 

P1

LS1010#show ip route 
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP 
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP 
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default 
       U - per-user static route, o - ODR 
       T - traffic engineered route 

Gateway of last resort is not set 

     1.0.0.0/32 is subnetted, 1 subnets 
O       1.1.1.1 [110/2] via 1.1.1.1, 19:00:12, ATM12/0/0 
     2.0.0.0/32 is subnetted, 1 subnets 
O       2.2.2.2 [110/3] via 3.3.3.3, 19:00:12, ATM12/0/1 
     3.0.0.0/32 is subnetted, 1 subnets 
O       3.3.3.3 [110/2] via 3.3.3.3, 19:00:12, ATM12/0/1 
     4.0.0.0/32 is subnetted, 1 subnets 
C       4.4.4.4 is directly connected, Loopback0 

LS1010#show tag-switching atm-tdp bindings 
 Destination: 4.4.4.4/32 
    Tailend Switch ATM12/0/0 1/33 Active -> Terminating Active 
    Tailend Switch ATM12/0/1 1/34 Active -> Terminating Active 
 Destination: 2.2.2.2/32 
    Transit ATM12/0/0 1/42 Active -> ATM12/0/1 1/35 Active 
 Destination: 1.1.1.1/32 
    Transit ATM12/0/1 1/33 Active -> ATM12/0/0 1/33 Active 
 Destination: 3.3.3.3/32 
    Transit ATM12/0/0 1/43 Active -> ATM12/0/1 1/34 Active 

P2

LS1010#show ip route 
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP 
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP 
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default 
       U - per-user static route, o - ODR 

Gateway of last resort is 10.118.1.21 to network 0.0.0.0 

     1.0.0.0/32 is subnetted, 1 subnets 
O       1.1.1.1 [110/3] via 4.4.4.4, 19:46:00, ATM0/1/1 
     2.0.0.0/32 is subnetted, 1 subnets 
O       2.2.2.2 [110/2] via 2.2.2.2, 19:46:00, ATM0/1/3 
     3.0.0.0/32 is subnetted, 1 subnets 
C       3.3.3.3 is directly connected, Loopback0 
     4.0.0.0/32 is subnetted, 1 subnets 
O       4.4.4.4 [110/2] via 4.4.4.4, 19:46:00, ATM0/1/1 
     10.0.0.0/24 is subnetted, 1 subnets 
C       10.118.1.0 is directly connected, Ethernet2/0/0 
S*   0.0.0.0/0 [1/0] via 10.118.1.21

LS1010#show tag-switching atm-tdp bindings 
 Destination: 1.1.1.1/32 
    Transit ATM0/1/3 1/33 Active -> ATM0/1/1 1/33 Active 
 Destination: 3.3.3.3/32 
    Tailend Switch ATM0/1/3 1/34 Active -> Terminating Active 
    Tailend Switch ATM0/1/1 1/34 Active -> Terminating Active 
 Destination: 4.4.4.4/32 
    Transit ATM0/1/3 1/35 Active -> ATM0/1/1 1/34 Active 
 Destination: 2.2.2.2/32 
    Transit ATM0/1/1 1/35 Active -> ATM0/1/3 1/33 Active 

PE2

Cisco7500#show ip route 
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP 
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP 
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area 
       * - candidate default, U - per-user static route, o - ODR 
       P - periodic downloaded static route 

Gateway of last resort is not set 

     1.0.0.0/32 is subnetted, 1 subnets 
O       1.1.1.1 [110/4] via 3.3.3.3, 02:58:46, ATM3/1/0.1 
     2.0.0.0/32 is subnetted, 1 subnets 
C       2.2.2.2 is directly connected, Loopback0 
     3.0.0.0/32 is subnetted, 1 subnets 
O       3.3.3.3 [110/2] via 3.3.3.3, 02:58:46, ATM3/1/0.1 
     4.0.0.0/32 is subnetted, 1 subnets 
O       4.4.4.4 [110/3] via 3.3.3.3, 02:58:46, ATM3/1/0.1 

Cisco7500#show ip route vrf NEW 
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP 
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP 
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area 
       * - candidate default, U - per-user static route, o - ODR 
       P - periodic downloaded static route 

Gateway of last resort is not set 

     100.0.0.0/24 is subnetted, 1 subnets 
B       100.1.1.0 [200/0] via 1.1.1.1, 01:16:13 
     110.0.0.0/24 is subnetted, 1 subnets 
C       110.1.1.0 is directly connected, FastEthernet3/0/0 
     10.0.0.0/24 is subnetted, 3 subnets 
B       10.3.3.0 [200/1] via 1.1.1.1, 01:16:13 
B       10.2.2.0 [200/1] via 1.1.1.1, 01:16:13 
B       10.1.1.0 [200/1] via 1.1.1.1, 01:16:13 
     30.0.0.0/24 is subnetted, 3 subnets 
R       30.3.3.0 [120/1] via 110.1.1.2, 00:00:16, FastEthernet3/0/0 
R       30.2.2.0 [120/1] via 110.1.1.2, 00:00:17, FastEthernet3/0/0 
R       30.1.1.0 [120/1] via 110.1.1.2, 00:00:17, FastEthernet3/0/0 

Cisco7500#show ip rip database vrf NEW 
10.0.0.0/8    auto-summary 
10.1.1.0/24    redistributed 
    [1] via 1.1.1.1, 
10.2.2.0/24    redistributed 
    [1] via 1.1.1.1, 
10.3.3.0/24    redistributed 
    [1] via 1.1.1.1, 
30.0.0.0/8    auto-summary 
30.1.1.0/24 
    [1] via 110.1.1.2, 00:00:09, FastEthernet3/0/0 
30.2.2.0/24 
    [1] via 110.1.1.2, 00:00:09, FastEthernet3/0/0 
30.3.3.0/24 
    [1] via 110.1.1.2, 00:00:09, FastEthernet3/0/0 
100.0.0.0/8    auto-summary 
100.1.1.0/24    redistributed 
    [1] via 1.1.1.1, 
110.0.0.0/8    auto-summary 
110.1.1.0/24    directly connected, FastEthernet3/0/0 
Cisco7500#show ip bgp vpnv4 vrf NEW 
BGP table version is 17, local router ID is 2.2.2.2 
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal 
Origin codes: i - IGP, e - EGP, ? - incomplete 

   Network          Next Hop            Metric LocPrf Weight Path 
Route Distinguisher: 200:1 (default for vrf NEW) 
*>i10.1.1.0/24      1.1.1.1                  1    100      0 ? 
*>i10.2.2.0/24      1.1.1.1                  1    100      0 ? 
*>i10.3.3.0/24      1.1.1.1                  1    100      0 ? 
*> 30.1.1.0/24      110.1.1.2                1         32768 ? 
*> 30.2.2.0/24      110.1.1.2                1         32768 ? 
*> 30.3.3.0/24      110.1.1.2                1         32768 ? 
*>i100.1.1.0/24     1.1.1.1                  0    100      0 ? 
*> 110.1.1.0/24     0.0.0.0                  0         32768 ? 

Cisco7500#show tag-switching interfaces 
Interface              IP    Tunnel   Operational 
ATM3/1/0.1             Yes   No       Yes         (ATM tagging) 

Cisco7500#show tag-switching interfaces detail 
Interface ATM3/1/0.1: 
        IP tagging enabled 
        TSP Tunnel tagging not enabled 
        Tagging operational 
        Tagswitching turbo vector 
        MTU = 4470 
        ATM tagging: 
                Tag VPI = 1 
                Tag VCI range = 33 - 65535 
                Control VC = 0/32 

Cisco7500#show tag-switching ? 
  atm-tdp           ATM Tagging Protocol information 
  cos-map           Show Tag CoS ATM Multi-VC CoS Map 
  forwarding-table  Show the Tag Forwarding Information Base (TFIB) 
  interfaces        Show per-interface tag switching 
  prefix-map        Show Tag CoS Prefix Map 
  tdp               Tag Distribution Protocol information

Cisco7500#show tag-switching tdp bindings 
  tib entry: 1.1.1.1/32, rev 25 
        local binding:  tag: 26 
  tib entry: 2.2.2.2/32, rev 2 
        local binding:  tag: imp-null 
  tib entry: 3.3.3.3/32, rev 27 
        local binding:  tag: 27 
  tib entry: 4.4.4.4/32, rev 29 
        local binding:  tag: 28 

Cisco7500#show tag-switching atm-tdp bindings 
 Destination: 1.1.1.1/32 
    Headend Router ATM3/1/0.1 (3 hops) 1/33  Active, VCD=8 
 Destination: 3.3.3.3/32 
    Headend Router ATM3/1/0.1 (1 hop) 1/34  Active, VCD=6 
 Destination: 4.4.4.4/32 
    Headend Router ATM3/1/0.1 (2 hops) 1/35  Active, VCD=7 
 Destination: 2.2.2.2/32 
    Tailend Router ATM3/1/0.1 1/33 Active, VCD=8 

Cisco7500#show tag-switching forwarding-table vrf NEW 
Local  Outgoing    Prefix            Bytes tag  Outgoing   Next Hop 
tag    tag or VC   or Tunnel Id      switched   interface 
33     Aggregate   110.1.1.0/24[V]   0 
34     Untagged    30.3.3.0/24[V]    0          Fa3/0/0    110.1.1.2 
35     Untagged    30.2.2.0/24[V]    0          Fa3/0/0    110.1.1.2 
36     Untagged    30.1.1.0/24[V]    0          Fa3/0/0    110.1.1.2 

CE2

Cisco7100#show ip route 
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP 
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP 
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area 
       * - candidate default, U - per-user static route, o - ODR 
       P - periodic downloaded static route 

Gateway of last resort is not set 

     100.0.0.0/24 is subnetted, 1 subnets 
R       100.1.1.0 [120/1] via 110.1.1.1, 00:00:19, FastEthernet0/0 
     110.0.0.0/24 is subnetted, 1 subnets 
C       110.1.1.0 is directly connected, FastEthernet0/0 
     10.0.0.0/24 is subnetted, 3 subnets 
R       10.3.3.0 [120/1] via 110.1.1.1, 00:00:19, FastEthernet0/0 
R       10.2.2.0 [120/1] via 110.1.1.1, 00:00:19, FastEthernet0/0 
R       10.1.1.0 [120/1] via 110.1.1.1, 00:00:19, FastEthernet0/0 
     30.0.0.0/24 is subnetted, 3 subnets 
C       30.3.3.0 is directly connected, Loopback2 
C       30.2.2.0 is directly connected, Loopback1 
C       30.1.1.0 is directly connected, Loopback0 

Related Information

Updated: Jun 05, 2005
Document ID: 10533