Guest

Asynchronous Connections

Comparing NextPort SPE Commands to MICA Modem Commands

Cisco - Comparing NextPort SPE Commands to MICA Modem Commands

Document ID: 9287

Updated: Feb 04, 2010

   Print

Introduction

This document compares the Software Port Entity (SPE) commands with their equivalent MICA commands.

Prerequisites

Requirements

There are no specific requirements for this document.

Components Used

The information in this document is based on a Cisco AS5400 that runs Cisco IOS® Software Release 12.1(4.1)T.

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Conventions

For more information on document conventions, refer to the Cisco Technical Tips Conventions.

NextPort to MICA Command Translations

EXEC Commands

Command Description Equivalent MICA Commands
show spe [slot/spe] [slot/spe] To show the SPE status. None
show spe log [reverse] [slot] To show the SPE system log. None
show spe modem summary | [slot/spe] [slot/spe] To show the modem service history statistics for specified SPEs. show modem [slot/port]
show spe modem active [slot/spe] [slot/spe] To show the statistics of all active calls on specified SPEs. show modem
show spe modem csr [[slot/spe | slot/spe-range] | summary [slot/spe-range]] To display the call success rate (CSR) for the specified SPE. None
show spe modem disconnect-reason [slot[/spe] [slot[/spe]] | [slot [slot]] [summary] To display all modem disconnect reasons for the specified SPEs. show modem call-stats
show spe modem high speed [slot[/spe] slot[/spe] [summary] To display the total number of connections that have been negotiated within each modulation or coder-decoder (codec) for specific range of SPEs. show modem speed
show spe modem high standard [slot[/spe] slot[/spe] [summary] To display the total number of connections that have been negotiated within each high modulation or codec for a specific range of SPEs or for all the SPEs. None
show spe modem low speed [slot[/spe] slot[/spe] [summary] To display the connect-speeds negotiated within each low speed modulation or codec for a specific range of SPEs or for all the SPEs. show modem speed
show spe modem low standard [slot[/spe] slot[/spe] | summary] To display the total number of connections that have been negotiated within each low modulation or codec for a specific range of SPEs or for all the SPEs. None
show spe version [slot[/spe] slot[/spe]] To display all MICA and NextPort firmware versions that are stored in Flash, and the firmware assigned to each SPE. show modem mapping
show port modem log [reverse] [slot[/port] slot[/port]] To display the events generated by the modem sessions. show modem log
show port operational-status [slot[/port] slot[/port]] To display the statistics of the current active session. show modem operational-status
show port config [slot[/port] slot[/port]] To display the configuration parameters of the current active session. show modem config
clear spe [slot/spe slot/spe] To reboot all specified SPEs. All calls will be torn down. None
clear spe counters [slot[/spe] slot[/spe]] To clear all statistics. clear modem counters
clear spe log [slot] To clear all log entries for specified SPEs. clear modem log
clear port [slot/port slot/port] To activate shut and no shut on specified ports. clear modem
clear port log [slot/port] [slot/port] To clear all log entries for the specified ports. clear modem log
show port modem calltracker [slot[/port] slot[/port]] To display call tracker information. For details, see Call Tracker plus ISDN and AAA Enhancements for the Cisco AS5300 and Cisco AS5800. show modem calltracker
show port modem test [slot[/port] slot[/port]] To display port modem test results. show modem test

SPE Configuration Commands

Command Description Equivalent MICA Commands
spe country To set the system country code. modem country
spe log-size To set the maximum log entries for each port. modem buffer-size
spe poll [auto | time][retry] To set the statistic polling interval. modem poll
spe call-record To generate a modem call record at the end of each call. modem call-record
spe [slot/spe [slot/spe]] To configure the SPE. Already implemented on the AS5300 and AS5800 platforms.
busyout To gracefully busy out active calls. modem busyout
shutdown To tear down all active calls on the specified SPEs. modem shutdown
port modem autotest To enable modem autotest. modem autotest
port modem startup-test To run a statup test on all the modems when the system boots up. modem startup-test
firmware upgrade [busyout | reboot | recovery] To specify the upgrade method. Already implemented on the 5300 platform.
firmware location filename To specify the firmware file to be upgraded. Already implemented on the 5300 and 5800 platforms.

Port Configuration Commands

Command Description Equivalent MICA Commands
port [slot/port slot/port] To configure the port range. modem range
default [busyout | shutdown] To display the value of the command to its default value. default modem busyout-threshold
busyout To busy out a port. modem busyout
shutdown To shut down a port. modem shutdown

Testing and Debugging Commands

Command Description Equivalent MICA Commands
debug port modem [maintenance] [slot[/spe] slot[/spe]] To debug modem maintenance. debug modem maintenance
debug spe country To display port management SPE country information. None
debug spe download-maintenance To display port management download maintenance. debug modem mica download
debug spe fm To debug firmware management. debug modem maintenance
debug spe sm To debug the SPE state machine. None
debug spe modem [error | statistics | trace] To display SPE modem statistics. debug modem [csm | trace]
debug csm modem [group] [slot/spe] To display call switching module (CSM) modem call information. debug modem csm
debug csm busyout To display CSM busyout events. debug csm busyout
debug csm neat To display CSM neat events. debug csm neat
debug nextport bs [api | cli | detail] To debug the NextPort bootstrap. None
debug nextport cli To test the NextPort command line interface (CLI) unit. None
debug nextport ddsm [api | command |detail | response] To display the NextPort Digital Data Services Manager. None
debug nextport dfc [api | cli | detail] To debug the NextPort Dial Feature Card (DFC). None
debug nextport est [module | api | data | rcv] To debug NextPort EST. None
debug nextport fd To debug NextPort Formatter and Dispatcher. None
debug nextport gdb To debug NextPort GDB source code. None
debug nextport md [api | callbacks | frame-error | init | oir | rx | throttle] To debug the NextPort modem driver. None
debug nextport mm [api | cli | detail] To debug the NextPort module manager. None
debug nextport msmgr [command | detail | response] To debug the NextPort modem service manager. None
debug nextport np-address To complete the address conversion from slot/port to NextPort. None
debug nextport secondaryq To debug the control message secondary queue. debug modem oob
debug nextport siglib [command | detail | response] To debug the NextPort Signalling Service Library. None
debug nextport spe [api | cli | detail] To debug the NextPort SPE Manager. None
debug nextport ssm [api | command | detail | oir | response] To debug the Nextport Session and Service Manager. None
test nextport Bs [crash_info | keepalive] To test the bootstrap unit test facility. None
test nextport ddsm api [get-llc-parameters | get-state | set-ppp-escape-map] To test the DDSM Cisco IOS NextPort Application Programming Interface (API). None
test nextport ddsm command [get-llc-parameters | get-running-parms | get-state | set-ppp-escape-map] To test the DDSM NextPort command messages. None
test nextport EST [add | cmdnak | delete | overflow | read | realtime | reporting | trace | rwite] To test the EST Manager unit test facility. None
test nextport mm [add | country | crash | delete | downloaded | hiirq | keepalive | loirq | nak1 | nak2 | nak3 | nop | norestart | overflow | qfail | qok | reporting | reset | restart | runtime | secondaryq] To test the Module Manager test facility. None
test nextport NP-address <1-6> To change the number of sessions per SPE. None
test nextport recovery threshold <1-10> To test the failure count that triggers recovery. None
test nextport set [dfc | module | port | slot | spe] number To set the test parameters. None
test nextport siglib [api | command] To test the Signaling Library Unit Test Facility. None
test nextport spesm information [buffers | bout [slot[/spe]] To test the SPE SM test commands. None
test nextport ssm [api | call-back | command | set [base-params | block-enable | params-count | service-type] To test the Unit Test Facility. None
test port modem back-to-back slot/spe slot/spe To execute back-to-back modem tests. test modem back-to-back slot/port slot/port
test oir [slot <1-8> [insert | remove]] To test online insertion and removal (OIR) simulation. None
busyout <slot number> To test graceful OIR removal. None

MICA to Nextport Command Translations

EXEC Commands

Command Description Equivalent NextPort Commands
show modem [slot/port] To show the modem service history statistics for specified SPEs. show spe modem summary | [slot/spe] [slot/spe]
show modem To show the statistics of all active calls on specified SPEs. show spe modem active [slot/spe] [slot/spe]
show modem call-stats To display all modem disconnect reasons for the specified SPEs. show spe modem disconnect-reason [slot[/spe] [slot[/spe]] | [slot [slot]] [summary]
show modem speed To display the total number of connections that have been negotiated within each modulation or coder-decoder (codec) for specific range of SPEs. show spe modem high speed [slot[/spe] slot[/spe] [summary]
show modem speed To display the connect-speeds negotiated within each low speed modulation or codec for a specific range of SPEs or for all the SPEs. show spe modem low speed [slot[/spe] slot[/spe] [summary]
show modem mapping To display all MICA and NextPort firmware versions that are stored in Flash, and the firmware assigned to each SPE. show spe version [slot[/spe] slot[/spe]]
show modem log To display the events generated by the modem sessions. show port modem log [reverse] [slot[/port] slot[/port]]
show modem operational-status To display the statistics of the current active session. show port operational-status [slot[/port] slot[/port]]
show modem config To display the configuration parameters of the current active session. show port config [slot[/port] slot[/port]]
clear modem counters To clear all statistics. clear spe counters [slot[/spe] slot[/spe]]
clear modem log To clear all log entries for specified SPEs. clear spe log [slot]
clear modem To activate shut and no shut on specified ports. clear port [slot/port slot/port]
clear modem log To clear all log entries for the specified ports. clear port log [slot/port] [slot/port]
show modem calltracker To display call tracker information. For more information, see Call Tracker plus ISDN and AAA Enhancements for the Cisco AS5300 and Cisco AS5800. show port modem calltracker [slot[/port] slot[/port]]
show modem test To display port modem test results. show port modem test [slot[/port] slot[/port]]

SPE Configuration Commands

Command Description Equivalent NextPort Commands
modem country To set the system country code. spe country
modem buffer-size To set the maximum log entries for each port. spe log-size
modem poll To set the statistic polling interval. spe poll [auto | time][retry]
modem call-record To generate a modem call record at the end of each call. spe call-record
spe [slot/spe slot/spe] (Already implemented on the AS5300 and AS5800 platforms.) To configure the SPE. spe [slot/spe [slot/spe]]
modem busyout To gracefully busyout active calls. busyout
modem shutdown To tear down all active calls on the specified SPEs. shutdown
modem autotest To enable modem autotest. port modem autotest
modem startup-test To run a statup test on all the modems when the system boots up. port modem startup-test
firmware upgrade [busyout | reboot | recovery] (Already implemented on the 5300 platform.) To specify the upgrade method. firmware upgrade [busyout | reboot | recovery]
firmware location filename (Already implemented on the 5300 and 5800 platforms.) To specify the firmware file to be upgraded. firmware location filename

Port Configuration Commands

Command Description Equivalent NextPort Commands
modem range To configure the port range. port [slot/port slot/port]
default modem busyout To display the value of the command to its default value. default [busyout | shutdown]
modem busyout To busy out a port. busyout
modem shutdown To shut down a port. shutdown

Testing and Debugging

Command Description Equivalent NextPort Commands
debug modem maintenance To debug modem maintenance. debug port modem [maintenance] [slot[/spe] slot[/spe]]
debug modem mica download To display port management download maintenance. debug spe download-maintenance
debug modem maintenance To debug firmware management. debug spe fm
debug modem [csm | trace] To display SPE modem statistics. debug spe modem [error | statistics | trace]
debug modem csm To display call switching module (CSM) modem call information. debug csm modem [group] [slot/spe]
debug csm busyout To display CSM busyout events. debug csm busyout
debug csm neat To display CSM neat events. debug csm neat
debug modem oob To debug the control message secondary queue. debug nextport secondaryq
test modem back-to-back slot/port slot/port To execute back-to-back modem tests. test port modem back-to-back slot/spe slot/spe

Related Information

Updated: Feb 04, 2010
Document ID: 9287