Cisco MGX 8800 Series Switches

Cisco MGX 8800/8900 Series 16-Port OC-3c/STM-1 ATM Switch Service Module

  • Viewing Options

  • PDF (134.8 KB)
  • Feedback

Product Overview

The Cisco MGX ® 8800/8900 Series Switches provide the industry's most scalable family of multiservice switches, scaling from 1.2 Gbps to 180 Gbps redundant switching capacity and from DS0 to OC-192/STM-64 interface capacity. This scalability provides exceptional savings and efficiency for network operations and services growth. The Cisco ® MGX 8800/8900 Series includes the Cisco MGX 8830/B, MGX 8850, MGX 8850/B, and MGX 8950 Multiservice Switches.
The Cisco 16-Port OC-3c/STM-1 ATM Switch Service Module is a line card for use in the Cisco MGX 8800/8900 Series multiservice Cisco MGX Switches in combination with the Cisco MGX 8800/8900 Series PXM-45 Processor Switch Module and the Cisco MGX 8950 XM-60 Switching Module (the latter for use on the Cisco MGX 8950 only). This ATM switch service module has 16 physical 155-Mbps interfaces that can be used to deliver high-density OC-3c or STM-1 trunking and User-Network Interface (UNI).
Up to 12 Cisco 16-port OC-3c/STM-1 ATM Switch Service Modules can reside in the Cisco MGX 8850, MGX 8850/B, or MGX 8950 to provide support for up to 192 OC-3c/STM-1 interfaces for service providers that require both high bandwidth and high network availability.
The Cisco 16-Port OC-3c/STM-1 ATM Switch Service Module meets service providers' demand for carrier-class availability by offering hot-standby 1+1 card redundancy as well as port redundancy with SONET/SDH automatic protection switching (APS). (See Figure 1.)

Figure 1. Cisco MGX 8800/8900 Series 16-Port OC-3c/STM-1 ATM Switch Service Module

Key Features

The main features of the Cisco MGX 8800/8900 16-Port OC-3c/STM-1 ATM Switch Service Module are listed here.

• Full nonblocking, full-duplex line-rate throughput on all 16 ports

• High reliability with hot-standby 1+1 16-port ATM switch service module card redundancy

• Per-virtual-path and per-virtual-circuit traffic shaping and available bit rate (ABR) with virtual source and virtual destination

• Y-cable and APS (1:1 and 1+1) port redundancy, plus APS 1+1 card redundancy

• Up to 4 million cell buffers

• Up to 16 classes of service (CoS) that can be used to support IP or ATM services

• Support for standards-based Private Network-to-Network Interface (PNNI), switched virtual circuit (SVC) and switched virtual path (SVP), soft permanent virtual connection (SPVC) and soft permanent virtual path (SPVP), and Multiprotocol Label Switching (MPLS) services

Technical Specifications

Table 1 lists the specifications for the Cisco 16-Port OC-3c/STM-1 ATM Switch Service Module.

Table 1. Product Specifications



Chassis Compatibility

Cisco MGX 8830/B, MGX 8850, MGX 8850/B, and MGX 8950

Software Compatibility

Cisco MGX 8800/8900 SW Release 5.0.20 and above



Port Density

16 ports

Layer 1 (Physical Layer) Feature Summary

• Support for ports and trunks on the same Cisco 155-Mbps 16-port ATM switch service module
• UNI 3.0, 3.1, and 4.0 physical layer specifications
• Compliance with the following SONET standards:
• Bellcore GR-253-CORE
• ANSI T1.105
• Compliance with the following SDH standards:
• ITU-T G.707, G.708, G.709, and G.783
• ITU-T G.957 and G.958

Layer 1 (Physical Layer) Feature Summary (continued)

Additional Physical Layer Specifications for Ports and Optics

Connection Options




Port speed

155 Mbps

155 Mbps

155 Mbps

Number of ports per Cisco MGX 8800/8900 Series 16-Port OC-3c/STM-1 ATM Switch Service Module




Port media




Port connector




Optics (nanometers- [nm])

Laser 1310 nm

Laser 1310 nm

Laser 1310 nm

Transmit power level (decibels per milliwatt [dBm])

-15 minimum and
-8 maximum

-15 minimum and
-8 maximum

-5 minimum and
-0 maximum

Receive power level (dBm)

-23 minimum and
-8 maximum

-28 minimum and
-8 maximum

-34 minimum and
-8 maximum

Typical reach

200 meters [218 yards) with 62.5 micrometer core) and 500 meters [545 yards] with 50 micrometer core

15 km [9.3 mi]

40 km [24.85 mi]


1+1 and 1:1 APS line

1+1 and 1:1 APS line

1+1 and 1:1 APS line

1Multimode fiber

2Single-mode fiber, short reach

3Single-mode fiber, long reach

Layer 2 (ATM) Feature Summary

• Configurable for trunk, Network-to-Network Interface (NNI), or UNI application
• Conformant to ATM Forum UNI 3.0, 3.1, and 4.0 and ITU-T I.361 and I.432 specifications
• Supports up to 16 CoS queues for IP and ATM traffic and includes all ATM Forum traffic-type services: ABR, unspecified bit rate (UBR), non-real-time variable bit rate (VBR-nrt), real-time variable bit rate (VBR-rt), constant bit rate (CBR); ABR supported with explicit forward congestion indicator (EFCI), RM marking, and explicit-rate stamping; supports ABR virtual source and destination
• Supports Integrated Local Management Interface (ILMI) 4.0
• Complies with standard usage parameter control (UPC) as specified by ATM Forum UNI 3.0 and 4.0, TM 4.1, and ITU-T I.371
• Supports early packet discard (EPD), Weighted Random Early Detection (WRED), and partial packet discard (PPD)
• Supports virtual circuit connections (VCCs) and virtual path connections (VPCs)
• Supports up to 128,000 connections per 16-port ATM switch service module controlled by PNNI
• Supports virtual path identifier (VPI) and virtual circuit identifier (VCI) range for VCCs and VPCs per UNI 3.1
• Supports virtual circuit merge, per-virtual-circuit and per-virtual-path shaping, and multipoint connections

Virtual trunks

• Supports a maximum of 128 virtual interfaces per module; the interfaces can be ports, trunks, or virtual trunks, and each virtual interface supports 16 CoS queues

Cell buffering

• Supports 4 million cells of buffering to accommodate large traffic bursts and avoid network congestion and cell discard; suitable for TCP/IP traffic

Support for dynamic routing using PNNI 1.0

• Offers an automatic end-to-end connection management mechanism
• Deterministically allocates bandwidth and reroutes connections autonomously over optimum network paths
• Preserves service integrity during network failure
• Offers E.164 and network-service-access-point (NSAP) addressing
• Offers support for SVC and SVP and for SPVC and SPVP
• Offers quality-of-service (QoS) based routing

Enhanced call admission control

• A user-programmable Enhanced Call Admission Control (E-CAC) feature determines whether to admit or deny connections based on the requested QoS.

Layer 2 (ATM) Feature Summary (continued)


• Statistics supported per connection
• Diagnostic statistics available per interface and CoS queues

Operation, administration, and management

• F4 to F5 fault propagation
• In-band diagnostics support using loopback cells
• In-band continuity check and automatic fault reporting for PVCs
• Loopback facility support for diagnostics and self-test purposes

Network Management

• Managed by Cisco WAN Manager software suite
• Based on Simple Network Management Protocol (SNMP)


• Input power required: -48 VDC
• Power consumption: 114W

Physical Dimensions

H x D: 15.83 x 15.65 in. (40.20 x 39.75 cm)


6.5 lb (2.95 kg)

Environmental Conditions

• Storage temperature: -40 to 158°F (-40 to 70°C)
• Operating temperature:
• Normal: 41 to 104°F (5 to 40°C)
• Short term: 23 to 122°F (-5 to 50°C)
• Relative humidity:
• Normal: 5 to 85%
• Short term: 5 to 90% but not to exceed 0.024 kg (0.048 lb) of water per kg (lb) of dry air

Short term refers to a period of not more than 96 consecutive hours and a total of not more than 15 days in 1 year

Approvals and Compliance

Table 2 lists regulatory information.

Table 2. Compliance and Agency Approvals

Compliance Type


Safety standards

• UL/CSA/IEC/EN 60950-1
• IEC/EN 60825 Laser Safety
• ACA TS001
• AS/NZS 60950
• FDA-Code of Federal Regulations Laser Safety


• FCC Class A
• ICES 003 Class A
• AS/NZS 3548 Class A
• CISPR 22 (EN55022) Class A
• VCCI Class A
• BSMI Class A
• IEC/EN 61000-3-2: Power Line Harmonics
• IEC/EN 61000-3-3: Voltage Fluctuations and Flicker

Immunity (basic standards)

• IEC/EN-61000-4-2: Electrostatic Discharge Immunity (8 kV Contact and 15 kV Air)
• IEC/EN-61000-4-3: Radiated Immunity (10 V/m)
• IEC/EN-61000-4-4: Electrical Fast Transient Immunity (2 kV AC Power and 1 kV DC Power)
• IEC/EN-61000-4-5: Surge AC Port (2 kV CM and 2 kV DM)
• IEC/EN-61000-4-5: Signal Ports (1 kV)
• IEC/EN-61000-4-5: Surge DC Port (1 kV)
• IEC/EN-61000-4-6: Immunity to Conducted Disturbances (10 Vrms)
• IEC/EN-61000-4-8: Power Frequency Magnetic Field Immunity (30 A/m)
• IEC/EN-61000-4-11: Voltage DIPS, Short Interruptions, and Voltage Variations

Network Equipment Building Systems (NEBS)

This product is designed to meet the following requirements (qualification in progress):

• SR-3580: NEBS Criteria Levels (Level 3)
• GR-1089-CORE: NEBS EMC and Safety
• GR-63-CORE: NEBS Physical Protection

Telcordia CLEI

• GR-485-CORE: CLEI coding
• GR-383-CORE: CLEI code product label
• GR-209-CORE: PCN process

Ordering Information

Table 3 lists ordering information for the Cisco MGX 8800/8900 Series 16-Port OC-3c/STM-1 ATM Switch Service Module.

Table 3. Ordering Information

Part Number

Product Name


Double-height ATM VS/VD service module, 16 OC-3c/STM-1


8-port SFP back card for OC-3/STM-1


Multi Mode Fiber FRU


Single Mode Fiber FRU, Intermediate Range


Single Mode Fiber FRU, Long Range


AXSM-XG Extender Connector for MGX 8950


SM Fiber Cable, IR or LR, with LC connector


Single Mode Fiber Y-Cable, LC connector, IR or LR


LC-To-SC Adapter Cable, SM and MM


APS connector for PXM1E, SRME and AXSM product family 


APS connector for MGX 8950 

Note: An MGX8950-EXTDR-CON is required with each AXSM-16-155-XG when this front card is configured on the Cisco MGX 8950.

For More Information

For more information about Cisco service and support programs and benefits, go to: