Cisco IP Phone 7821/7841/7861 Firmware Load 10.1(1) SIP

Firmware Version 10.1(1) for Cisco Unified IP Phone 7821/7841/7861 (SIP)

The 10.1(1) firmware image within the installation program supports the SIP protocol for the following Cisco Unified IP Phones:

· Cisco Unified IP Phone 7821/7841/7861

This firmware version is supported on Cisco Unified Communications Manager 8.5(1) and later.

Release Notes and Documentation

For a list of Resolved Problems and Known Problems with this firmware version, you can obtain the Firmware Release Notes by clicking the following URL:

http://www.cisco.com/en/US/products/ps10453/prod_release_notes_list.html-TOBEUPDATED

For all phone documentation, click the following URL:

Cisco Unified IP Phone 7821/7841/7861:

http://www.cisco.com/en/US/products/ps10453/tsd_products_support_series_home.html-TOBEUPDATED

Installing the Firmware Load

Before using the Cisco Unified IP Phone 7821/7841/7861 with Cisco Unified Communications Manager Release 8.5(1) or later, you must install the latest firmware on all Cisco Unified Communications Manager servers in the cluster.

The 10.1(1) installation programs for the Cisco Unified IP Phone 7821/7841/7861 are listed below.

Note: For the Cisco Unified IP Phone 7821/7841/7861, you should not add the .loads extension to the firmware version name in the Cisco Unified Communications Manager database.

Cisco Unified IP Phone 7821/7841/7861 Installation Instructions

Perform the following procedure:

1. Click the following URL: http://www.cisco.com/cisco/web/support/index.html#~shp_download.

2. Log in to the Support and Downloads Software page.

3. Choose the Voice and Unified Communications Category.

4. Choose the IP Telephony folder.

5. Choose the Unified Communications Endpoints folder.

6. Choose Cisco Unified IP Phones 7800 Series.

7. Choose Cisco Unified IP Phone 7821/7841/7861.

8. Choose Session Initiation Protocol (SIP) Software.

9. Choose 10.1(1) under the Latest Releases folder.

10. Download the files that are listed in Table 1 to your hard drive.

Table 1: Cisco Unified IP Phone 7821/7841/7861 Firmware Loads

Cisco Unified IP Phone Model	Cisco Unified Communications Manager Version	Installer name on Software Page	MD5 hash
78xx	8.5(1) or later	cmterm-78xx.10-1-1-9.cop.sgn	5a25c22b55da25a57bf4f826ca99df45

11. Using your web browser, log in to the Cisco Unified OS Administration web page.

12. Under the Software Upgrades menu, select Install/Upgrade.

13. Fill in the appropriate values in the Software Location section for the downloaded files as listed in Table 1 and click Next.

14. In the Options/Upgrades drop-down box, select a file you downloaded and click Next.

15. Enusre that the downloaded file has the same MD5 hash value as listed in Table 1.

16. Click Next.

17. Check the installation log and verify the file installed successfully.

18. To install another file, click Install Another and repeat steps 6 – 16.

19. Log in to Cisco Unified Serviceability web page.

20. Under the Tools menu, select Control Center - Feature Services.

21. Select the Cisco Tftp service, and click the Restart button.

Verifying the Firmware Load

You may verify the installation of the firmware as follows:

1. Log in to the Cisco Unified CM Administration web page.

2. Under the Device menu, select Device Settings > Device Defaults.

3. Verify the new firmware image name is listed in the Load Information field for the Cisco Unified IP Phone 7821/7841/7861.

Cisco Unified IP Phone 7821/7841/7861 Alternate Firmware Format

The Cisco Unified IP Phone 7821/7841/7861 firmware version 10.1(1) is also supplied in a zip file as an alternative, in case a Cisco Unified Communications Manager is not available to load the installer program. The name of this file is: cmterm-78xx.10-1-1-9_REL.zip.

After unzipping the firmware files, they should be manually copied to the appropriate directory on the TFTP server.