Feedback
Table Of Contents
Cisco NX-OS Interfaces Commands
dual-active exclude interface-vlan
port-channel load-balance ethernet
show interface counters errors
show interface counters storm-control
show interface port-channel counters
show port-channel compatibility-parameters
show port-channel load-balance
show port-channel rbh-distribution
show running-config interface mgmt
show vpc consistency-parameters
Cisco NX-OS Interfaces Commands
This chapter describes the Cisco NX-OS interfaces commands.
bandwidth (interface)
To set the inherited and received bandwidth values for an interface, use the bandwidth command in interface configuration mode. To restore the default values, use the no form of this command.
bandwidth {kbps | inherit [kbps]}
no bandwidth {kbps | inherit [kbps]}
Syntax Description
Defaults
1000000 kbps
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
The bandwidth command sets an informational parameter to communicate only the current bandwidth to the higher-level protocols; you cannot adjust the actual bandwidth of an interface using this command.
Note
This is a routing parameter only. It does not affect the physical interface.
The bandwidth inherit command controls how a subinterface inherits the bandwidth of its main interface.
The no bandwidth inherit command enables all subinterfaces to inherit the default bandwidth of the main interface, regardless of the configured bandwidth. If a bandwidth is not configured on a subinterface, and you use the bandwidth inherit command, all subinterfaces will inherit the current bandwidth of the main interface. If you configure a new bandwidth on the main interface, all subinterfaces will use this new value.
If you do not configure a bandwidth on the subinterface and you configure the bandwidth inherit command on the main interface, the subinterfaces will inherit the specified bandwidth.
In all cases, if an interface has an explicit bandwidth setting configured, then that interface will use that setting, regardless of whether the bandwidth inheritance setting is in effect.
This command does not require a license.
Examples
This example shows how to configure all subinterfaces off this main interface to inherit the configured bandwidth:
switch(config-if)# bandwidth inherit 30000Related Commands
beacon
To enable the beacon mode for an interface, use the beacon command. To disable the beacon mode for an interface, use the no form of this command.
beacon
no beacon
Syntax Description
This command has no arguments or keywords.
Command Default
Disabled
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
The beacon mode allows you to identify a physical port by flashing its link-state LED with a green light. To identify the physical port for an interface, you activate the beacon parameter for the interface.
This command does not require a license.
Examples
This example shows how to enable the beacon mode for the Ethernet port 3/1:
switch(config)# interface ethernet 3/1switch(config-if)# beaconswitch(config-if)#Related Commands
show interface
Displays the interface status, which includes the beacon mode state.
carrier-delay
To set the carrier delay on an interface, use the carrier-delay command. To return to the default carrier delay value, use the no form of this command.
carrier-delay {sec | {msec value}}
no carrier-delay
Syntax Description
sec
Seconds of delay. The range of values is from 0 to 60.
value
Milliseconds of delay. The range of values is from 0 to 1000.
Defaults
The default is 2 seconds or 100 milliseconds.
Command Modes
Interface
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
Note
If a link goes down and comes back up before the carrier delay timer expires, the down state is effectively filtered, and the rest of the software on the device is not aware that a link-down event occurred. A large carrier delay timer results in fewer link-up/link-down events being detected. When you set the carrier delay time to 0, the device detects each link-up/link-down event that occurs.
Note
In most environments, a lower carrier delay time is better than a higher one. The exact value that you choose depends on the nature of the link outages and how long you expect these linkages to last in your network. If your data links are subject to short outages (especially if those outages last less time than it takes for your IP routing to converge) you should set a long carrier delay value to prevent these short outages from causing unnecessary churn in your routing tables. However, if you outages tend to be longer, then you may want to set a shorter carrier delay time so that the outages are detected sooner, and the IP route convergence begins and ends sooner.
This command does not require a license.
Examples
This example shows how to set the carrier delay timer to 20 minutes for VLAN 6:
switch(config)# interface vlan 6switch(config-if)# carrier-delay 20switch(config-if)#Related Commands
channel-group
To assign and configure a physical interface to a port-channel group, use the channel-group command. To remove the channel-group configuration from the interface, use the no form of this command.
channel-group number [force] [mode {active | on | passive}]
no channel-group [number]
Syntax Description
number
Number of channel group. Maximum number of port channels that can be configured is 256 across all VDCs, and the range of values is from 1 to 4096.
force
Forces the interface to join the channel group, although some parameters are not compatible. See Usage Guidelines below for information on the compatibility parameters and which ones can be forced.
mode
Specifies the port-channel mode of the interface.
on
This is the default channel mode, and all port channels that are not running LACP remain in this mode. If you attempt to change the channel mode to active or passive before enabling LACP, the device returns an error message.
After you enable LACP globally, by using the feature lacp command, you enable LACP on each channel by configuring the channel mode as either active or passive. An interface in this mode does not initiate or respond to LACP packets. When an LACP attempts to negotiate with an interface in the on state, it does not receive any LACP packets and becomes an individual link with that interface; it does not join the channel group.The default mode is on.
active
Specifies that when you enable the Link Aggregation Control Protocol (LACP), this command enables LACP on the specified interface. Interface is in active negotiating state, in which the port initiates negotiations with other ports by sending LACP packets.
passive
Specifies that when you enable LACP, this command enables LACP only if an LACP device is detected.The interface is in a passive negotiation state, in which the port responds to LACP packets that it receives but does not initiate LACP negotiation.
Defaults
None
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
Use this command to create a channel group that includes the interface that you are working on and to add or remove specific interfaces from the channel group. Use this command to move a port from one channel group to another. You enter the channel group that you want the port to move to; the device automatically removes the specified from its present channel group and adds that port to the specified channel group.
After you enable LACP globally, by using the feature lacp command, you enable LACP on each channel by configuring the channel mode as either active or passive. A port channel in the on channel mode is a pure port channel and can aggregate a maximum of eight ports. It does not run LACP.
You cannot change the mode for an existing port channel or any of its interfaces if that port channel is not running LACP; the channel mode remains as on. The system returns an error message if you try.
All ports in one port channel must be in the same virtual device context (VDC). With LACP enabled, this requirement applies to the possible eight active ports and the possible eight standby ports. The port channels can originate in one VDC (with all ports in that channel in the same VDC) and partner with a port channel in another VDC (again, all ports in that channel must be in that VDC).
Use the no form of this command to remove the physical interface from the port channel. When you delete the last physical interface from a port channel, the port channel remains. To delete the port channel completely, use the no form of this interface port-channel command.
The compatibility check includes the following operational attributes:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Use the show port-channel compatibility-parameters command to see the full list of compatibility checks that the Cisco NX-OS uses.
You can only add interfaces configured with the channel mode set to on to static port channels, that is without a configured aggregation protocol. And you can only add interfaces configured with the channel mode as active or passive to port channels that are running LACP.
You can configure these attributes on an individual member port. If you configure a member port with an incompatible attribute, Cisco NX-OS suspends that port in the port channel.
Alternatively, you can force ports with incompatible parameters to join the port channel as long the following parameters are the same:
•
•
•
•
•
•
When the interface joins a port channel, some of its individual parameters are removed and replaced with the values on the port channel, as follows:
•
•
•
•
•
•
•
•
•
•
•
Also, many interface parameters remain unaffected with the interface joins or leaves a port channel, as follows:
•
•
•
•
•
•
•
•
•
•
If subinterfaces are configured for the port-channel interface and a member port is removed from the port channel, the configuration of the port-channel subinterface is not propagated to the member ports.
Any configuration changes that you make in any of the compatibility parameters to the port-channel interface are propagated to all interfaces within the same channel group as the port channel (for example, configuration changes are also propagated to the physical interfaces that are not part of the port channel but are part of the channel group).
You do not have to create a port-channel interface before you assign a physical interface to a channel group. A port-channel interface is created automatically when the channel group gets its first physical interface, if it is not already created.
You can create either a Layer 2 or a Layer 3 port channel by entering the interface port-channel command or when the channel group gets its first physical interface assignment. The port channels are not created at run time or dynamically.
This command does not require a license.
Examples
This example shows how to add an interface to LACP channel group 5 in active mode:
switch(config-if)# channel-group 5 mode activeswitch(config-if)#Related Commands
clear counters interface
To clear the interface counters, use the clear counters interface command.
clear counters interface {all | ethernet slot/port | loopback number | mgmt number | port-channel channel-number | tunnel tunnel-number | vlan vlan-number}
Syntax Description
Command Default
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to clear and reset the counters on Ethernet port 5/5:
switch# clear counters interface ethernet 5/5switch#Related Commands
show interface counters
Displays in and out counters for all interfaces in the system.
clear lacp counters
To clear the statistics for all interfaces for Link Aggregation Control Protocol (LACP) groups, use the clear lacp counters command.
clear lacp counters [interface port-channel channel-number]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
If you enter this command for a static port-channel group, without the aggregation protocol enabled, the device ignores the command.
If you do not specify a channel number, the LACP counters for all LACP port groups are cleared.
This command does not require a license.
Examples
This example shows how to clear all the LACP counters:
switch(config)# clear lacp countersswitch(config) #This example shows how to clear all LACP counters for the LACP port-channel group 20:
switch(config)# clear lacp counters interface port-channel 20switch(config)#Related Commands
clear vpc statistics
To clear virtual port-channel (vPC) statistics, use the clear vpc statistics command.
clear vpc statistics {all | peer-keepalive | peer-link | vpc number}
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
Use the clear vpc statistics command to clear the vPC statistics. If the feature is not enabled, this command is unavailable.
The clear vpc statistics peer-link and clear vpc statistics vpc number commands are redirected to the appropriate port channel and the clear statistics port-channel channel-number command.
This command does not require a license.
Examples
This example shows how to clear the statistics for vPC 10:
switch(config)# clear vpc statistics vpc 10switch(config) #Related Commands
show vpc statistics
Displays vPC statistical information on vPCs. If the feature is not enabled, the system displays an error when you enter this command.
delay
To configure the interface throughput delay for Ethernet interfaces, use the delay command. To remove the configured throughput delay, use the no form of this command.
delay value
no delay
Syntax Description
value
Specify the delay time in tens of microseconds. You can set an informational value range between 1 and 16777215 tens of microseconds.
Command Default
10 microseconds for all interfaces except loopback ports
5000 microseconds for loopback ports
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Beginning with Cisco NX-OS Release 4.2(1) for the Cisco Nexus 7000 Series devices, the default delay values are changed. Prior to this release, all the default delay value for all interfaces was 100 microseconds.
Note
Specifying a value for the throughput delay provides a value for use by Layer 3 protocols; it does not change the actual throughput delay of an interface.
This command does not require a license.
Examples
This example shows how to configure the throughput-delay time to 100,000 microseconds for the slot 3 port 1 Ethernet interface:
switch(config)# interface ethernet 3/1switch(config-if)# delay 10000Related Commands
show interface
Displays information about the interface, which includes the delay parameter.
delay restore
To delay the vPC coming up on the restored vPC peer device after a reload and after the peer adjacency is established and the VLAN interfaces are back up, use the delay restore command. To return to the default value, use the no form of the command.
delay restore seconds
no delay restore seconds
Syntax Description
Defaults
30 seconds
Command Modes
vpc-domain command mode.
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the delay restore command to avoid upstream traffic from the access device to the core from being dropped when you restore the vPC peer devices. Sometimes, the restored vPCs may come up before the routing tables are converged, and you may see packet drops.
The delay restore command delays bringing up the vPC after the peer adjacency has formed and VLAN interface are up on the restored device after a reload to let the routing protocols converge.
This command does not require a license.
Examples
This example shows how to configure the delay reload:
switch# config tswitch(config)# vpc domain 5switch(config-vpc-domain)# delay restore 40Related Commands
description
To provide textual interface descriptions for the Ethernet and management interfaces, use the description command. To remove the description, use the no form of the command.
description text
Syntax Description
Command Default
None
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
You use the description command to provide textual interface descriptions. Descriptions can be a maximum of 80 case-sensitive alphanumeric characters.
This command does not require a license.
Examples
This example shows how to add the description server1 to the Ethernet interface on slot 5, port 2:
switch(config)# interface ethernet 5/1switch(config-if)# description server1Related Commands
show interface
Displays information about the interface, which includes the description parameter.
dual-active exclude interface-vlan
To ensure that certain VLAN interfaces are not shut down on the virtual port-channel (vPC) secondary peer device when the vPC peer link fails for those VLANs carried on the vPC peer link but not on the vPC configuration itself, use the dual-active exclude interface-vlan command. To return to the default value, use the no form of this command.
dual-active exclude interface-vlan {range}
no dual-active exclude interface-vlan {range}
Syntax Description
Command Default
None
Command Modes
vpc-domain configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the dual-active exclude interface-vlan command to ensure that those VLAN interfaces on the vPC secondary peer device that are carried on the vPC peer link but not by the vPC configuration itself do not go down if the vPC peer link fails. The VLAN interfaces must have already been configured.
Note
This command does not require a license.
Examples
This example shows how to configure the device to keep the VLAN interfaces up on the vPC peer devices if the peer link fails:
switch# config tswitch(config)# vpc-domain 5switch(config-vpc-domain)# dual-active exclude interface-vlan 10Related Commands
vpc-domain
Configures a vPC domain and enters the vpc-domain configuration mode.
duplex
To specify the duplex mode as full, half, or autonegotiate, use the duplex command. To return the system to default mode, use the no form of this command.
duplex {full | half | auto}
no duplex {full | half | auto}
Syntax Description
full
Specify the duplex mode as full.
half
Specify the duplex mode as half.
auto
Specify the duplex mode as autonegotiate.
Command Default
None
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
The interface speed that you specify can affect the duplex mode used for an interface, so you should set the speed before setting the duplex mode. If you set the speed for autonegotiation, the duplex mode is automatically set to be autonegotiated. If you specify 10- or 100-Mbps speed, the port is automatically configured to use half-duplex mode, but you can specify full-duplex mode instead. Gigabit Ethernet is full duplex only. You cannot change the duplex mode on Gigabit Ethernet ports or on a 10/100/1000-Mbps port that is set for Gigabit Ethernet.
See the Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide for more information on interface speed and duplex settings.
This command does not require a license.
Examples
This example shows how to specify the duplex mode for full-duplex:
switch(config-if)# duplex fullRelated Commands
show interface
Displays information about the interface, which includes the duplex parameter.
encapsulation dot1Q
To enable IEEE 802.1Q encapsulation of traffic on a specified subinterface in a virtual LAN (VLAN), use the encapsulation dot1q command in subinterface configuration mode. To disable encapsulation, use the no form of this command.
encapsulation dot1Q vlan-id
no encapsulation dot1Q vlan-id
Syntax Description
vlan-id
VLAN to set when the interface is in access mode; valid values are from 1 to 4094, except for the VLANs reserved for internal switch use.
Defaults
No encapsulation
Command Modes
Subinterface configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
IEEE 802.1Q encapsulation is configurable on Ethernet interfaces. IEEE 802.1Q is a standard protocol for interconnecting multiple switches and routers and for defining VLAN topologies.
Use the encapsulation dot1q command in subinterface range configuration mode to apply a VLAN ID to the subinterface.
This command does not require a license.
Examples
This example shows how to enable dot1Q encapsulation on a subinterface for VLAN 30:
switch(config-subif)# encapsulation dot1q 30Related Commands
errdisable detect cause
To enable error-disabled (errdisable) detection for an application, use the errdisable detect cause command. To return to the default setting, use the no version of this command.
errdisable detect cause {acl-exception | all | link-flap | loopback}
no errdisable detect cause {acl-exception | all | link-flap | loopback}
Syntax Description
Command Default
Disabled
Command Modes
Global configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the errdisable detect cause command to enable error detection for an application.
A cause is defined as the reason why the error-disabled state occurred. When a cause is detected on an interface, the interface is placed in an error-disabled state. This error-disabled state is an operational state that is similar to the link-down state. You must enter the shutdown command and then the no shutdown command to recover an interface manually from the error-disabled state.
This command does not require a license.
Examples
This example shows how to enable error-disabled detection on all cases:
switch(config)# errdisable detect cause allRelated Commands
shutdown
Brings the port down administratively.
no shutdown
Brings the port up administratively.
show interface status err-disabled
Displays the interface error-disabled state.
errdisable recovery cause
To enable the automatic recovery from the error-disabled (errdisable) state for an application, use the errdisable recovery cause command. To return to the default setting, use the no version of this command.
errdisable recovery cause {all | bpduguard | link-flap | failed-port-state | psecure-violation | security-violation | storm-control | udld | vpc-peerlink}
no errdisable recovery cause {all | bpduguard | link-flap | psecure-violation | security-violation | storm-control | udld | vpc-peerlink}
Syntax Description
Command Default
Disabled
Command Modes
Global configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the errdisable recovery cause command to enable automatic recovery on the interface from the error-disabled state for an application. This command tries to bring the interface out of the error-disabled state and retry operation once all the causes have timed out. The interface automatically tries to come up again after 300 seconds. To change this interval, use the errdisable recovery interval command.
This command does not require a license.
Examples
This example shows how to automatically recover from the error-disabled state for link flapping after you have enabled the recovery timer:
switch(config)# errdisable recovery cause link-flapRelated Commands
errdisable recovery interval
Enables the recovery timer.
show interface status err-disabled
Displays interface error-disabled state.
errdisable recovery interval
To enable the recovery timer, use the errdisable recovery interval command.
errdisable recovery interval interval
Syntax Description
Command Default
300 seconds
Command Modes
Global configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the errdisable recovery interval command to configure the recovery timer.
This command does not require a license.
Examples
This example shows how to configure the recovery timer:
switch(config)# errdisable recovery interval 32Related Commands
errdisable recovery cause
Enables the error-disabled recovery for an application.
show interface status err-disabled
Displays the interface error-disabled state.
feature interface-vlan
To enable the creation of VLAN interfaces (switched virtual interfaces [SVI]), use the feature interface-vlan command in global configuration mode. To disable the VLAN interface feature, use the no form of this command.
feature interface-vlan
no feature interface-vlan
Syntax Description
This command has no arguments or keywords.
Defaults
Disabled
Command Modes
Global configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
You must use the feature interface-vlan command before you can create VLAN interfaces.
This command does not require a license.
Examples
This example shows how to enable the interface VLAN feature:
switch(config)# feature interface-vlanRelated Commands
feature lacp
To enable Link Aggregation Control Protocol (LACP) port channeling on the device, use the feature lacp command. To disable LACP on the device, use the no form of this command.
feature lacp
no feature lacp
Syntax Description
This command has no arguments or keywords.
Defaults
Disabled
Command Modes
Global configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
You must remove all the LACP configuration parameters from all port channels on the device before you can disable LACP. You cannot disable LACP while LACP configurations remain on the device.
Even after you enable LACP globally, you do not have to run LACP on all port channels on the device. You enable LACP on each channel mode using the channel-group mode command.
When you enter the no form of this command, the system removes all the LACP configuration from the device.
This command does not require a license.
Examples
This example shows how to enable LACP port channeling on the device:
switch(config)# feature lacpRelated Commands
feature tunnel
To enable the creation of tunnel interfaces, use the feature tunnel command in global configuration mode. To disable the tunnel interface feature, use the no form of this command.
feature tunnel
no feature tunnel
Syntax Description
This command has no arguments or keywords.
Defaults
Disabled
Command Modes
Global configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
You must use the feature tunnel command before you can create tunnel interfaces.
This command requires the Enterprise license.
Examples
This example shows how to enable the interface tunnel feature:
switch(config)# feature tunnelRelated Commands
feature udld
To enable UDLD globally on the device, use the feature udld command. To disable UDLD globally on the device, use the no feature udld command.
feature udld
no feature udld
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Global configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the feature udld command to enable UDLD globally on the device. UDLD must be also enabled on the other linked interface and its device. After enabling the devices, it is possible to enable a UDLD mode for an interface.
Use the no feature udld command to disable UDLD globally for Ethernet interfaces on the device.
This command does not require a license.
Examples
This example shows how to enable the UDLD for a device:
switch# config tswitch(config)# feature udldThis example shows how to disable UDLD for a device:
switch# config tswitch(config)# no feature udldRelated Commands
feature vpc
To enable virtual port channels (vPCs), use the feature vpc command. To return to the default setting, use the no form of this command.
feature vpc
no feature vpc
Syntax Description
This command has no arguments or keywords.
Defaults
Disabled
Command Modes
Global configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
You must use the feature vpc command to enable the vPC functionality. You must enable vPCs before you can configure them.
Note
This command does not require a license.
Examples
This example shows how to enable vPC functionality on the device:
switch(config)# feature vpcRelated Commands
flowcontrol
To enable or disable the ability of the Ethernet port to send and receive flow-control pause frames, use the flowcontrol command. To return to the default flow-control settings, use the no version of the command.
flowcontrol {send | receive} {desired | on | off}
no flowcontrol {send | receive}
Syntax Description
Command Default
1-Gb/s interfaces—Off for receive; off for send
10-Gb/s interfaces—Off for receive; off for send
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the flowcontrol command to enable or disable the ability of the Ethernet port to send and receive flow-control pause frames.
Make sure that the remote port has the corresponding setting for the flow control that you need. If you want the local port to send flow-control pause frames, the remote port has a receive parameter set to on or desired. If you want the local port to receive flow-control frames, you must make sure that the remote port has a send parameter set to on or desired. If you do not want to use flow control, you can set the remote port's send and receive parameters to off.
For Ethernet ports that run at 1 Gbps or faster, you can enable or disable the port's ability to send and receive flow-control pause frames. For Ethernet ports that run slower than 1 Gbps, you can enable or disable only the port's ability to receive pause frames.
When enabling flow control for the local port, you either fully enable the local port to send or receive frames regardless of the flow-control setting of the remote port, or you set the local port to use the desired setting used by the remote port. If you enable both the local and remote ports for flow control, or set the desired flow control of the other port, or set a combination of those two states, flow control is enabled for those ports.
Note
To see how the different port flow-control states affect the link flow-control state, see Table 1.
This command does not require a license.
Examples
This example shows how to set Ethernet port 3/1 to send flow-control pause frames:
switch# config tswitch(config)# interface ethernet 3/1switch(config-if)# flowcontrol send onRelated Commands
show interface flowcontrol
Displays information about the interface flowcontrol.
show interface
Displays information about the interface, which includes the flowcontrol parameter.
inherit port-profile
To assign a port profile to an interface or range of interfaces and to inherit an additional port profile onto an existing port profile, use the inherit port-profile command. To remove an inherited port profile or to remove a port profile from specified interfaces, use the no form of this command.
inherit port-profile name
no inherit port-profile name
Syntax Description
name
Port profile that you want to assign to interfaces or to inherit onto the existing port profile.
Defaults
None
Command Modes
Interface configuration
Port-profile configurationSupported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the inherit port-profile command to do the following:
•
•
See the port-profile command and the state-enabled command for information about creating, configuring, and enabling port profiles.
If you attempt to inherit a port profile to the wrong type of interface, the system returns an error.
When you remove a port profile from a range of interfaces, the system undoes the configuration from the interfaces first and then removes the port-profile link itself. Also, when you remove a port profile, the system checks the interface configuration and either skips port-profiles commands that have been overridden by directly entered interface commands or returns the command to the default value.
You can also choose a subset of interfaces from which to remove a port profile from those interfaces to which you originally applied the profile. For example, if you configured a port profile and configured 10 interfaces to inherit that port profile, you can remove the port profile from just some of the specified 10 interfaces. The port profile continues to operate on the remaining interfaces to which it is applied.
You use the port-profile configuration mode to remove an inherited port profile from an original port profile.
This command does not require a license.
Examples
This example shows how to assign a specified port profile to a range of interfaces:
switch(config)# interface ethernet 2/1-10switch(config-if)# port-profile testThis example shows how to inherit the configuration parameters from the port profile named switch onto the port profile named test:
switch(config)# testswitch(config-ppm)# inherit port-profile switchRelated Commands
interface cmp-mgmt module
To create a CMP management interface and enter interface configuration mode, use the interface cmp-mgmt module command.
interface cmp-mgmt module number
Syntax Description
Defaults
None
Command Modes
Global configuration
Interface configurationSupported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the interface cmp-mgmt module command to create a CMP management interface.
This command does not require a license.
Examples
This example shows how to create a CMP management interface:
switch(config)# interface cmp-mgmt module 9switch(config-if-cmp)#interface ethernet
To configure an Ethernet interface and enter interface configuration mode, use the interface ethernet command.
interface ethernet slot/port
Syntax Description
Defaults
None
Command Modes
Global configuration
Interface configurationSupported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the interface ethernet command to enter the interface configuration mode for the specified interface or range of interfaces.
This command does not require a license.
Examples
This example shows how to enter the interface command mode for the Ethernet interface on slot 2, port 1:
switch(config)# interface ethernet 2/1switch(config-if)#Related Commands
show interface ethernet slot/port
Displays information about the Ethernet interface.
interface loopback
To create a loopback interface and enter interface configuration mode, use the interface loopback command. To remove a loopback interface, use the no form of this command.
interface loopback number
no interface loopback number
Syntax Description
Defaults
None
Command Modes
Global configuration
Interface configurationSupported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
Use the interface loopback command to create or modify loopback interfaces.
This command does not require a license.
Examples
This example shows how to create a loopback interface:
switch(config)# interface loopback 50switch(config-if)#Related Commands
show interface loopback
Displays information about the traffic on the specified loopback interface.
interface mgmt
To configure the management interface and enter interface configuration mode, use the interface management command.
interface mgmt0
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Global configuration
Interface configurationSupported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
Use the interface mgmt0 command to configure the management interface and to enter the interface configuration mode.
This command does not require a license.
Examples
This example shows how to enter the interface configuration mode to configure the management interface:
switch(config)# interface mgmt0switch(config-if)#Related Commands
show interface mgmt0
Displays information about the traffic on the management interface.
interface port-channel
To create a port-channel interface and enter interface configuration mode, use the interface port-channel command. To remove a logical port-channel interface or subinterface, use the no form of this command.
interface port-channel channel-number
no interface port-channel channel-number
Syntax Description
channel-number
Channel number that is assigned to this port-channel logical interface. The range of valid values is from 1 to 4096.
Defaults
None
Command Modes
Global configuration
Interface configurationSupported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
Use the interface port-channel command to create or delete port-channel groups and to enter the interface configuration mode for the port channel.
You can create port channels implicitly using the bandwidth (interface) command or explicitly using the feature tunnel command.
A port can belong to only one channel group.
You can create subinterfaces on a Layer 3 port-channel interface. However, you cannot add a Layer 3 interface that has existing subinterfaces to a port channel.
Note
The Link Aggregation Control Protocol (LACP) system ID is unique for each VDC, and channel-group numbers and names can be re-used in different VDCs.
When you use the interface port-channel command, follow these guidelines:
•
•
•
This command does not require a license.
Examples
This example shows how to create a port-channel group interface with channel-group number 50:
switch(config)# interface port-channel 50switch(config-if)#Related Commands
interface tunnel
To create a tunnel interface and enter interface configuration mode, use the interface tunnel command. To remove a tunnel interface, use the no form of this command.
interface tunnel number
no interface tunnel number
Syntax Description
Defaults
None
Command Modes
Global configuration
Interface configurationSupported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
Use the interface tunnel command to create or modify tunnel interfaces.
Cisco NX-OS supports the GRE header defined in IETF RFC 2784. Cisco NX-OS does not support tunnel keys and other options from IETF RFC 1701.
You can configure IP tunnels only in the default virtual device context (VDC).
This command requires the Enterprise license.
Examples
This example shows how to create a tunnel interface:
switch(config)# interface tunnel 50switch(config-if)#Related Commands
interface vlan
To create a VLAN interface and enter interface configuration mode, use the interface vlan command. To remove a VLAN interface, use the no form of this command.
interface vlan vlan-id
no interface vlan vlan-id
Syntax Description
vlan-id
VLAN to set when the interface is in access mode; valid values are from 1 to 4094, except for the VLANs reserved for the internal switch use.
Defaults
None
Command Modes
Global configuration
Interface configurationSupported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
Use the interface vlan command to create or modify VLAN interfaces.
The VLAN interface is created the first time that you enter the interface vlan command for a particular VLAN. The vlan-id argument corresponds to the VLAN tag that is associated with the data frames on an Inter-Switch Link (ISL), the IEEE 802.1Q-encapsulated trunk, or the VLAN ID that is configured for an access port.
This command does not require a license.
Examples
This example shows how to create a VLAN interface for VLAN 50:
switch(config)# interface vlan 50switch(config-if)#Related Commands
feature interface-vlan
Enables the ability to create VLAN interfaces.
show interface vlan
Displays information about the traffic on the specified VLAN interface.
lacp graceful-convergence
To configure port-channel graceful convergences for the Link Aggregation Control Protocol (LACP), use the lacp graceful-convergence command. To disable port-channel graceful convergences, use the no form of this command.
lacp graceful-convergence
no lacp graceful-convergence
Syntax Description
This command has no arguments or keywords.
Defaults
LACP graceful convergence is enabled.
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
By default LACP graceful convergence is enabled. In situations where you need to support LACP interoperability with devices where the graceful failover defaults may delay the time taken for a disabled port to be brought down or cause traffic from the peer to be lost, you can disable convergence.
Caution
Note
This command does not require a license.
Examples
This example shows how to disable LACP graceful convergence on a port channel:
switch (config)# interface port-channel 1switch(config-if)# shutdownswitch(config-if)# no lacp graceful-convergenceswitch(config-if)# no shutdownRelated Commands
lacp port-priority
To set the priority for the physical interfaces for the Link Aggregation Control Protocol (LACP), use the lacp port-priority command. To return the port priority to the default value, use the no form of this command.
lacp port-priority priority
no lacp port-priority
Syntax Description
Defaults
32768
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
Each port configured to use LACP has an LACP port priority. You can accept the default value of 32768 for the LACP port priority, or you can configure a value between 1 and 65535. LACP uses the port priority in combination with the port number to form the port identifier. The port priority is used with the port number to form the port identifier. The port priority is used to decide which ports should be put into standby mode when there is a hardware limitation that prevents all compatible ports from aggregating or when you have more than eight ports configured for the channel group.
When setting the priority, note that a higher number means a lower priority.
This command does not require a license.
Examples
This example shows how to set the LACP port priority for the interface to 2000:
switch(config-if)# lacp port-priority 2000Related Commands
lacp suspend-individual
To enable individual Link Aggregation Control Protocol (LACP) port suspension behavior on a port channel, use the lacp suspend-individual command. To disable individual port suspension behavior on the port channel, use the no form of this command.
lacp suspend-individual
no lacp suspend-individual
Syntax Description
This command has no arguments or keywords.
Defaults
LACP suspend-individual is enabled.
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
By default LACP suspend-individual is enabled. LACP sets a port to the suspended state if it does not receive an LACP PDU from the peer. This can cause some servers to fail to boot up as they require LACP to logically bring-up the port. You can tune behavior to individual use.
Note
This command does not require a license.
Examples
This example shows how to disable LACP suspend-individual on a port channel:
switch (config)# interface port-channel 1switch(config-if)# shutdownswitch(config-if)# no lacp suspend-individualswitch(config-if)# no shutdownRelated Commands
lacp system-priority
To set the system priority of the device for the Link Aggregation Control Protocol (LACP), use the lacp system-priority command. To return the system priority to the default value, use the no form of this command.
lacp system-priority priority
no lacp system-priority
Syntax Description
Defaults
32768
Command Modes
Global configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
Each device that runs LACP has an LACP system priority value. You can accept the default value of 32768 for this parameter, or you can configure a value between 1 and 65535. LACP uses the system priority with the MAC address to form the system ID and also during negotiation with other systems. The system ID is unique for each virtual device context (VDC).
When setting the priority, note that a higher number means a lower priority.
This command does not require a license.
Examples
This example shows how to set the LACP system priority for the device to 2500:
switch(config)# lacp system-priority 2500switch(config)#Related Commands
show lacp
Displays LACP information.
show lacp system identifier
Displays information on the LACP system identifier.
link debounce
To enable the debounce timer for Ethernet ports and specify a debounce time, use the link debounce command. To disable the timer, use the no form of this command.
link debounce [time milliseconds]
no link debounce
Syntax Description
time milliseconds
(Optional) Debounce timer for the time you want to specify. The range of time is from 0 to 5000 ms.
Command Default
Enabled
100 milliseconds
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the link debounce command to enable the debounce timer for Ethernet ports and set it for a specified amount of time in milliseconds. The default debounce time applies when you enter the link debounce command with no arguments.
The range of time is from 1 to 5000 ms. The debounce timer is disabled if you specify the time to 0 ms.
This command does not require a license.
Examples
This example shows how to enable the debounce timer and set the debounce time to 1000 ms for the Ethernet port 3/1:
switch# config tswitch(config)# interface ethernet 3/1switch(config-if)# link debounce time 1000This example shows how to disable the debounce timer for the Ethernet port 3/1:
switch# config tswitch(config)# interface ethernet 3/1switch(config-if)# no link debounceRelated Commands
show interface debounce
Displays the debounce time information about the interface.
load-interval
To change the sampling interval for statistics collections on interfaces, use the load-interval command. To return to the default sampling interval, use the no form of this command.
load-interval [counter {1 | 2 | 3}] seconds
no load-interval [counter {1 | 2 | 3}] [seconds]
Syntax Description
Command Default
1—30 seconds; 60 seconds for VLAN network interface
2—300 seconds
3—not configured
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the load-interval command to obtain bit-rate and packet-rate statistics for three different durations.
You can set the statistics collection intervals on the following types of interfaces:
•
•
•
You cannot use this command on the management interface or subinterfaces.
This command sets the sampling interval for such statistics as packet rate and bit rate on the specified interface.
This command does not require a license.
Examples
This example shows how to set the three sample intervals for the Ethernet port 3/1:
switch# config tswitch(config)# interface ethernet 3/1switch(config-if)# load-interval counter 1 60switch(config-if)# load-interval counter 2 135switch(config-if)# load-interval counter 3 225Related Commands
max-ports
To assign a maximum possible number of interfaces that a port profile can inherit, use the max-ports command. To return to the default value, use the no form of this command.
max-ports number
no max-ports number
Syntax Description
number
Maximum number of interfaces that a port profile can inherit. The range is from 1 to 512 ports, and there is no default value.
Defaults
None
Command Modes
Port-profile configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
You must be in the port-profile configuration mode in order to issue this command.
You must enable each specific port profile using the state-enabled command.
This command does not require a license.
Examples
This example shows how to enter the port-profile configuration mode and to configure the maximum possible number of interfaces that a port profile can inherit:
switch(config)# port-profile type ethernet type testswitch(config-ppm)# max-ports 500Related Commands
state-enabled
Enables a specified port profile.
show port-profile
Displays information about port profiles.
mdix auto
To enable automatic medium-dependent independent crossover (MDIX) detection for the interface, use the mdix auto command. To turn automatic detection off, use the no form of this command.
mdix auto
no mdix
Syntax Description
This command has no arguments or keywords.
Command Default
Enabled
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the mdix auto command to enable automatic MDIX detection for the port. Use the no mdix command to disable MDIX detection for the port.
This command is only available on copper Ethernet ports. To detect the type of connection (crossover or straight) with another copper Ethernet port, enable the MDIX parameter for the local port. Before you begin, MDIX must be enabled on the remote port.
This command does not require a license.
Examples
This example shows how to enable MDIX for Ethernet port 3/1:
switch# config tswitch(config)# interface ethernet 3/1switch(config-if)# mdix autoThis example shows how to disable MDIX for Ethernet port 3/1:
switch# config tswitch(config)# interface ethernet 3/1switch(config-if)# no mdixRelated Commands
show interface
Displays information about the interface, which includes the MDIX status.
medium
To set the medium mode for an interface, use the medium command in interface configuration command. To remove the entry, use the no form of this command.
medium {broadcast | p2p}
no medium {broadcast | p2p}
Syntax Description
broadcast
Configures the interface as a broadcast medium.
p2p
Configures the interface as a point-to-point medium.
Defaults
None
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
The medium command is used to configure the interface as broadcast or point to point.
This command does not require a license.
Examples
This example shows how to configure the interface for point-to-point medium:
switch(config-if)# medium p2pmtu
To configure the maximum transmission unit (MTU) size for Layer 2 and Layer 3 Ethernet interfaces, use the mtu command. To return to the default value, use the no form of this command.
mtu size
no mtu
Syntax Description
Command Default
1500 bytes
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the mtu size command to configure the MTU size for Layer 2 and Layer 3 Ethernet interfaces.
For Layer 3 interfaces, you can configure the MTU to be between 576 and 9216 bytes (even values are required). For Layer 2 interfaces, you can configure the MTU to be either the system default MTU (1500 bytes) or the system jumbo MTU size (which has the default size of 9216 bytes).
Note
This command does not require a license.
Examples
This example shows how to configure the Layer 2 Ethernet port 3/1 with the default MTU size (1500):
switch# config tswitch(config)# interface ethernet 3/1switch(config-if)# mtu 1500Related Commands
show interface
Displays information about the interface, which includes the MTU size.
peer-gateway
To configure the device to send virtual port-channel (vPC) packets to the device's MAC address, use the peer-gateway command. To return to the default value, use the no form of this command.
peer-gateway
no peer-gateway
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
vpc-domain configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the peer-gateway command to have a vPC peer device act as the gateway even for packets that are destined to the vPC peer device's MAC address.
This command does not require a license.
Examples
This example shows how to configure the device to use the switch gateway even for the packets that are destined the vPC:
switch# config tswitch(config)# vpc-domain 5switch(config-vpc-domain)# peer-gatewayRelated Commands
vpc-domain
Configures a vPC domain and enters the vpc-domain configuration mode.
peer-keepalive destination
To configure the virtual port-channel (vPC) peer-keepalive link and message between vPC peer devices, use the peer-keepalive destination command.
peer-keepalive destination ipaddress
[hold-timeout secs]
[interval msecs {timeout secs}
[{precedence {prec-value | network | internet | critical | flash-override | flash | immediate | priority | routine}} | {tos {tos-value | max-reliability | max-throughput | min-delay | min-monetary-cost | normal}} | tos-byte tos-byte-value]
[source ipaddress]
[udp-port number]
[vrf {name | management | vpc-keepalive}]
Syntax Description
.
Defaults
Peer-keepalive is disabled.
Hold-timeout is 3 seconds.
Interval is 1000 milliseconds.
Timeout is 5 seconds.
Precedence is default, with a level of 6 (internet).
UDP port is 3200.
VRF is management VRF.
Command Modes
vpc-domain configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
You must enable the vPC feature before you can configure the peer-keepalive parameters. The vPC keepalive messages notify the system if one of the vPC peer devices goes down.
Note
Although the keepalive messages can transmit over any Layer 3 topology, we recommend that you create and configure a separate VRF with Layer 3 ports on each vPC peer device as the source and destination for the vPC keepalive messages. The default ports and VRF for the peer-alive link are the management ports and the management VRF. Do not use the peer link itself for the vPC peer-keepalive messages.
Note
The vPC keepalive messages are IP/UDP messages.
This command accepts only IPv4 addresses.
Note
The device assumes that its vPC peer device is down when the device does not receive any messages from the peer during the timeout period. We recommend that you configure the timeout value to be three times the interval value.
You can configure either the precedence, tos, or tos-byte value to ensure throughput for the vPC peer-keepalive message.
Note
This command does not require a license.
Examples
This example shows how to configure the IP address of the remote vPC peer device for the fault-tolerant link:
switch(config-vpc-domain)# peer-keepalive destination 172.28.231.85Related Commands
port-channel load-balance ethernet
To set the load-balancing method among the interfaces in the channel-group bundle, use the port-channel load-balance ethernet command. To return the system priority to the default value, use the no form of this command.
port-channel load-balance ethernet method [module slot]
no port-channel load-balance ethernet [method [module slot]]
Syntax Description
method
Load-balancing method. See the "Usage Guidelines" section for a list of valid values.
module slot
(Optional) Specifies the module slot number.
Defaults
Layer 2 packets—source-dest-mac
Layer 3 packets—source-dest-ip-port
Command Modes
Global configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
When you do not specify a module, you are configuring load balancing for the entire device. When you use the module parameter, you are configuring load balancing for the specified modules
Valid method values are as follows:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Note
Use the module argument to configure the module independently for port-channeling and load-balancing mode. When you do this, the remaining module use the current load-balancing method configured for the entire device, or the default method if you have not configured a method for the entire device. When you enter the no argument in conjunction with a module argument, the load-balancing method for the specified module takes the current load-balancing method that is in use for the entire device. If you configured a load-balancing method for the entire device, the specified module uses that configured method, rather than the default source-dest-ip-port/source-dest-mac. The per module configuration takes precedence over the load-balancing method configured for the entire device.
You can configure one load-balancing mode for the entire device, a different mode for specified modules, and yet another mode for other specified modules. The per module configuration takes precedence over the load balancing configuration for the entire device.
Use the option that provides the balance criteria with the greatest variety in your configuration. For example, if the traffic on a port channel is going only to a single MAC address and you use the destination MAC address as the basis of port channel load balancing, the port channel always chooses the same link in that port channel; using source addresses or IP addresses might result in better load balancing.
This command does not require a license.
Examples
This example shows how to set the load-balancing method for the entire device to use the source port:
switch(config)# port-channel load-balance ethernet source-portRelated Commands
show port-channel load-balance
Displays information on port-channel load balancing.
port-profile
To create a port profile and enter the port-profile configuration mode or to enter into the port-profile configuration mode of a previously created port profile, use the port-profile command. To remove the port profile, use the no form of this command.
port-profile [type {ethernet | interface-vlan | port-channel}] name
no port-profile [type {ethernet | interface-vlan | port-channel}] name
Syntax Description
Defaults
None
Command Modes
Interface configuration
Port-profile configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
Use the port-profile command to group configuration commands and apply them to several interfaces simultaneously. All interfaces in the range must be the same type. The maximum number of interfaces that can inherit a single port profile is 512.
The port-profile name must be globally unique across types and networks.
Each port profile can be applied only to a specific type of interface; the choices are as follows:
•
•
•
Note
A subset of commands are available under the port-profile configuration mode, depending on which interface type you specify. Layer 3 and CTS commands are not supported by port profiles.
You can configure the following port-profile operations:
•
•
•
•
•
•
•
You inherit the port profile when you attach the port profile to an interface or range of interfaces. The maximum number of interfaces that can inherit a single profile is 512. When you attach, or inherit, a port profile to an interface or range of interfaces, the system applies all the commands in that port profile to the interfaces.
Additionally, you can have one port profile inherit another port profile, which allows the initial port profile to assume all of the commands of the second, inherited, port profile that do not conflict with the initial port profile. Four levels of inheritance are supported except for the switchport private-vlan mapping and private-vlan mapping commands, which support only one level of inheritance. See the inherit port-profile command for information about inheriting an additional port profile and assigning port profiles to specified interfaces.
The system applies the commands inherited by the interface or range of interfaces according to the following guidelines:
•
•
•
•
•
Note
If you delete a specific configuration for a specified range of interfaces using the interface configuration mode, that configuration is also deleted from the port profile for that range of interfaces only. For example, if you have a channel group inside a port profile and you are in the interface configuration mode and you delete that port channel, the specified port channel is also deleted from the port profile as well.
Just as in the device, you can enter a configuration for an object in port profiles without that object being applied to interfaces yet. For example, you can configure a virtual routing and forward instance (VRF) without it being applied to the system. If you then delete that VRF and its configurations from the port profile, the system is unaffected.
After you inherit a port profile on an interface or range of interfaces and you delete a specific configuration value, that port-profile configuration will not operate on the specified interfaces.
You must enable each specific port profile using the state-enabled command.
This command does not require a license.
Examples
This example shows how to configure, name a port profile, and enter the port-profile configuration mode:
switch(config)# port-profile type ethernet testswitch(config-ppm)#Related Commands
state-enable
Enables a specified port profile.
show port-profile
Displays information about port profiles.
rate-mode dedicated
To set the dedicated rate mode for the specified ports, use the rate-mode dedicated command.
rate-mode dedicated
no rate-mode
Syntax Description
This command has no arguments or keywords.
Command Default
Shared rate mode is the default.
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the rate-mode dedicated command to set the dedicated rate mode for the specified ports.
On a 32-port 10-Gigabit Ethernet module, each set of four ports can handle 10 gigabits per second (Gb/s) of bandwidth. You can use the rate-mode parameter to dedicate that bandwidth to the first port in the set of four ports or share the bandwidth across all four ports.
Note
Table 1-2 identifies the ports that are grouped together to share each 10 Gb/s of bandwidth and which port in the group can be dedicated to utilize the entire bandwidth.
Note
When you enter the rate-mode dedicated command, the full bandwidth of 10 Gb is dedicated to one port. When you dedicate the bandwidth, all subsequent commands for the port are for dedicated mode.
This command does not require a license.
Examples
This example shows how to configure the dedicated rate mode for Ethernet ports 4/17, 4/19, 4/21, and 4/23:
switch# config tswitch(config)# interface ethernet 4/17, ethernet 4/19, ethernet 4/21, ethernet 4/23switch(config-if)# shutdownswitch(config-if)# interface ethernet 4/17switch(config-if)# rate-mode dedicatedswitch(config-if)# no shutdownRelated Commands
show interface
Displays interface information, which includes the current rate mode dedicated.
rate-mode shared
To set the shared rate mode for the specified ports, use the rate-mode shared command.
rate-mode shared
Syntax Description
This command has no arguments or keywords.
Command Default
Shared rate mode is the default.
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the rate-mode shared command to set the shared rate mode for the specified ports. This is the default rate mode for the module.
That is, use the rate-mode shared command to specify that each 10 Gb of bandwidth on a 32-port 10 GE Ethernet module is shared by ports in the same port group.
If the port group is in dedicated rate mode, you must first administratively shut down the ports in the group, change the rate mode to shared, and then bring the ports administratively up.
This command does not require a license.
Examples
This example shows how to configure the shared rate mode for Ethernet ports 4/17, 4/19, 4/21, and 4/23:
switch# config tswitch(config)# interface ethernet 4/17, ethernet 4/19, ethernet 4/21, ethernet 4/23switch(config-if)# shutdownswitch(config-if)# interface ethernet 4/17switch(config-if)# rate-mode sharedswitch(config-if)# no shutdownRelated Commands
show interface
Displays interface information, which includes the current rate mode shared.
role priority
To override the default selection of virtual port-channel (vPC) primary and secondary devices when you create a vPC domain, use the role priority command. To return to the default vPC system priority, use the no form of this command.
role priority priority
no role priority
Syntax Description
Defaults
32667
Command Modes
vpc-domain command mode.
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
You must enable the vPC feature before you can create a vPC system priority
By default, the system elects a primary and secondary vPC peer device after you configure the vPC domain and both sides of the vPC peer link. However, you may want the system to elect a specific vPC peer device as the primary device for the vPC. Then, you would manually configure the role value for the vPC peer device that you want as primary to be lower than that of the other vPC peer device.
This command does not require a license.
Examples
This example shows how to create a vPC role priority:
switch# config tswitch(config)# vpc domain 5switch(config-vpc-domain)# role priority 2000Related Commands
show vpc role
Displays the role for this device for the vPC domain as primary or secondary.
show interface
To display the interface status and information, use the show interface command.
show interface
Syntax Description
This command has some keywords. For more details, see the Usage Guidelines for this command.
Command Default
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the show interface command to display the interface status and information. To display show interface commands with valid keywords, see the following commands in this document:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
This command does not require a license.
Examples
This example shows how to display the interface status and information:
switch# show interfacemgmt0 is upHardware: GigabitEthernet, address: 0019.076c.1a78 (bia 0019.076c.1a78)Internet Address is 172.28.231.193/23MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,reliability 255/255, txload 1/255, rxload 1/255Encapsulation ARPAfull-duplex, 1000 Mb/sAuto-Negotiation is turned on1 minute input rate 26608 bits/sec, 10 packets/sec1 minute output rate 2272 bits/sec, 0 packets/secRx473804 input packets 51412 unicast packets 124811 multicast packets297581 broadcast packets 148270388 bytesTx51994 output packets 50387 unicast packets 1460 multicast packets147 broadcast packets 8330595 bytesEthernet2/1 is down (Administratively down)Hardware: 10/100/1000 Ethernet, address: 0018.bad8.3ffd (bia 0019.076c.4dac)MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,reliability 255/255, txload 1/255, rxload 1/255Encapsulation ARPAauto-duplex, auto-speedBeacon is turned offAuto-Negotiation is turned onInput flow-control is off, output flow-control is offAuto-mdix is turned onSwitchport monitor is offLast clearing of "show interface" counters never1 minute input rate 0 bits/sec, 0 packets/sec1 minute output rate 0 bits/sec, 0 packets/secL3 in Switched:ucast: 0 pkts, 0 bytes - mcast: 0 pkts, 0 bytesL3 out Switched:ucast: 0 pkts, 0 bytes - mcast: 0 pkts, 0 bytesRx0 input packets 0 unicast packets 0 multicast packets0 broadcast packets 0 jumbo packets 0 storm suppression packets0 bytesTx0 output packets 0 multicast packets0 broadcast packets 0 jumbo packets0 bytes0 input error 0 short frame 0 watchdog0 no buffer 0 runt 0 CRC 0 ecc0 overrun 0 underrun 0 ignored 0 bad etype drop0 bad proto drop 0 if down drop 0 input with dribble0 input discard0 output error 0 collision 0 deferred0 late collision 0 lost carrier 0 no carrier0 babble0 Rx pause 0 Tx pause0 interface resets...<additional lines truncated>Related Commands
interface
Enters the interface configuration mode, and configures the types and identities of interfaces.
show interface brief
To display brief information about the interface, use the show interface brief command.
show interface [ethernet slot/port | port-channel channel-number] command
Syntax Description
ethernet slot/port | port- channel channel-number
(Optional) Type and number of the interface that you want to display.
Command Default
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
If you do not specify an interface, this command displays information about all Layer 2 interfaces. Use the show interface brief command to display brief information about the interface.
This command does not require a license.
Examples
This example shows how to display brief information about the interface:
switch# show interface brief--------------------------------------------------------------------------------Port VRF Status IP Address Speed MTU--------------------------------------------------------------------------------mgmt0 -- up 172.28.231.193 1000 1500--------------------------------------------------------------------------------Ethernet VLAN Type Mode Status Reason Speed PortInterface Ch #--------------------------------------------------------------------------------Eth2/1 -- eth routed down Administratively down auto(D) --Eth2/2 -- eth routed down Administratively down auto(D) --Eth2/3 -- eth routed down Administratively down auto(D) --Eth2/4 1 eth pvlan down Administratively down auto(D) --Eth2/5 -- eth routed down Administratively down auto(D) --Eth2/6 1 eth access down Link not connected auto(D) --Eth2/7 1 eth access up none 1000(D) --Eth2/8 -- eth routed down Administratively down auto(D) --Eth2/9 1 eth access up none 1000(D) --Eth2/10 1 eth access down Link not connected auto(D) --Eth2/11 -- eth routed down Administratively down auto(D) --Eth2/12 -- eth routed down Administratively down auto(D) --Eth2/13 -- eth routed down Administratively down auto(D) --Eth2/14 -- eth routed down Administratively down auto(D) --Eth2/15 -- eth routed down Administratively down auto(D) --Eth2/16 -- eth routed down Administratively down auto(D) --Eth2/17 -- eth routed down Administratively down auto(D) --Eth2/18 -- eth routed down Administratively down auto(D) --Eth2/19 -- eth routed down Administratively down auto(D) --Eth2/20 -- eth routed down Administratively down auto(D) --Eth2/21 -- eth routed down Administratively down auto(D) --Eth2/22 -- eth routed down Administratively down auto(D) --Eth2/23 -- eth routed down Administratively down auto(D) --Eth2/24 -- eth routed down Administratively down auto(D) --Eth2/25 -- eth routed down Administratively down auto(D) --Eth2/26 -- eth routed down Administratively down auto(D) --Eth2/27 -- eth routed down Administratively down auto(D) --Eth2/28 -- eth routed down Administratively down auto(D) --Eth2/29 -- eth routed down Administratively down auto(D) --Eth2/30 -- eth routed down Administratively down auto(D) --Eth2/31 -- eth routed down Administratively down auto(D) --Eth2/32 -- eth routed down Administratively down auto(D) --Eth2/33 -- eth routed down Administratively down auto(D) --Eth2/34 -- eth routed down Administratively down auto(D) --Eth2/35 -- eth routed down Administratively down auto(D) --Eth2/36 -- eth routed down Administratively down auto(D) --Eth2/37 -- eth routed down Administratively down auto(D) --Eth2/38 -- eth routed down Administratively down auto(D) --Eth2/39 -- eth routed down Administratively down auto(D) --Eth2/40 -- eth routed down Administratively down auto(D) --Eth2/41 -- eth routed down Administratively down auto(D) --Eth2/42 -- eth routed down Administratively down auto(D) --Eth2/43 -- eth routed down Administratively down auto(D) --Eth2/44 -- eth routed down Administratively down auto(D) --Eth2/45 -- eth routed down Administratively down auto(D) --Eth2/46 -- eth routed down Administratively down auto(D) --Eth2/47 -- eth routed down Administratively down auto(D) --Eth2/48 -- eth routed down Administratively down auto(D) ---------------------------------------------------------------------------------Interface Secondary VLAN(Type) Status Reason-------------------------------------------------------------------------------Vlan1 -- down noneRelated Commands
interface
Enters the interface configuration mode, and configures the types and identities of interfaces.
show interface capabilities
To display information about the interface capabilities, use the show interface capabilities command.
show interface [ethernet slot/port | port-channel channel-number] capabilities
Syntax Description
ethernet slot/port | port-channel channel-number
(Optional) Type and number of the interface that you want to display.
Command Default
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the show interface capabilities command to display information about the capabilities of the interface such as the speed, duplex, and rate mode. If you do not specify an interface, this command displays information about all Layer 2 interfaces.
This command does not require a license.
Examples
This example shows how to display the capabilities for a specific interface:
switch# show interface ethernet 2/7 capabilitiesEthernet2/7Model: COPPERType: 1000BaseTSpeed: 10,100,1000,autoDuplex: half/full/autoTrunk encap. type: 802.1QChannel: yesBroadcast suppression: percentage(0-100)Flowcontrol: rx-(off/on/desired),tx-(off/on/desired)Rate mode: dedicatedQOS scheduling: rx-(2q4t),tx-(1p3q4t)CoS rewrite: yesToS rewrite: yesSPAN: yesUDLD: yesLink Debounce: yesLink Debounce Time: yesMDIX: yesPort Group Members: noneRelated Commands
interface
Enters the interface configuration mode, and configures the types and identities of interfaces.
show interface counters
To display in and out counters for all interfaces in the system, use the show interface counters command.
show interface [ethernet slot/port | port-channel channel-number] counters
Syntax Description
ethernet slot/port | port-channel channel-number
(Optional) Type and number of the interface that you want to display
Command Default
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the show interface counters command to display in and out counters for all or a specific interface. If you do not specify an interface, this command displays information about all Layer 2 interfaces.
This command does not require a license.
Examples
This example shows how to display the in and out counters for all interfaces:
switch# show interface counters--------------------------------------------------------------------------------Port InOctets InUcastPkts InMcastPkts InBcastPkts--------------------------------------------------------------------------------mgmt0 137046816 46882 115497 267729Eth2/1 0 0 0 0Eth2/2 0 0 0 0Eth2/3 0 0 0 0Eth2/4 0 0 0 0Eth2/5 0 0 0 0Eth2/6 0 0 0 0Eth2/7 295061 0 1348 0Eth2/8 0 0 0 0Eth2/9 4174381 0 53303 0Eth2/10 0 0 0 0Eth2/11 0 0 0 0Eth2/12 0 0 0 0Eth2/13 0 0 0 0Eth2/14 0 0 0 0Eth2/15 0 0 0 0Eth2/16 0 0 0 0Eth2/17 0 0 0 0Eth2/18 0 0 0 0Eth2/19 0 0 0 0Eth2/20 0 0 0 0Eth2/21 0 0 0 0Eth2/22 0 0 0 0Eth2/23 0 0 0 0Eth2/24 0 0 0 0Eth2/25 0 0 0 0Eth2/26 0 0 0 0Eth2/27 0 0 0 0Eth2/28 0 0 0 0Eth2/29 0 0 0 0Eth2/30 0 0 0 0Eth2/31 0 0 0 0Eth2/32 0 0 0 0Eth2/33 0 0 0 0Eth2/34 0 0 0 0Eth2/35 0 0 0 0Eth2/36 0 0 0 0Eth2/37 0 0 0 0Eth2/38 0 0 0 0Eth2/39 0 0 0 0Eth2/40 0 0 0 0Eth2/41 0 0 0 0Eth2/42 0 0 0 0Eth2/43 0 0 0 0Eth2/44 0 0 0 0Eth2/45 0 0 0 0Eth2/46 0 0 0 0Eth2/47 0 0 0 0Eth2/48 0 0 0 0Vlan1 0 0 0 ----------------------------------------------------------------------------------Port OutOctets OutUcastPkts OutMcastPkts OutBcastPkts--------------------------------------------------------------------------------mgmt0 7555343 45951 1352 136Eth2/1 0 0 0 0Eth2/2 0 0 0 0Eth2/3 0 0 0 0Eth2/4 0 0 0 0Eth2/5 0 0 0 0Eth2/6 0 0 0 0Eth2/7 4174381 0 53303 0Eth2/8 0 0 0 0Eth2/9 295061 0 1348 0Eth2/10 0 0 0 0Eth2/11 0 0 0 0Eth2/12 0 0 0 0Eth2/13 0 0 0 0Eth2/14 0 0 0 0Eth2/15 0 0 0 0Eth2/16 0 0 0 0Eth2/17 0 0 0 0Eth2/18 0 0 0 0Eth2/19 0 0 0 0Eth2/20 0 0 0 0Eth2/21 0 0 0 0Eth2/22 0 0 0 0Eth2/23 0 0 0 0Eth2/24 0 0 0 0Eth2/25 0 0 0 0Eth2/26 0 0 0 0Eth2/27 0 0 0 0Eth2/28 0 0 0 0Eth2/29 0 0 0 0Eth2/30 0 0 0 0Eth2/31 0 0 0 0Eth2/32 0 0 0 0Eth2/33 0 0 0 0Eth2/34 0 0 0 0Eth2/35 0 0 0 0Eth2/36 0 0 0 0Eth2/37 0 0 0 0Eth2/38 0 0 0 0Eth2/39 0 0 0 0Eth2/40 0 0 0 0Eth2/41 0 0 0 0Eth2/42 0 0 0 0Eth2/43 0 0 0 0Eth2/44 0 0 0 0Eth2/45 0 0 0 0Eth2/46 0 0 0 0Eth2/47 0 0 0 0Eth2/48 0 0 0 0Vlan1 0 0 0 --Related Commands
show interface counters errors
To display interface error counters, use the show interface counters errors.
show interface [ethernet slot/port | port-channel channel-number] counter errors
Syntax Description
ethernet slot/port | port-channel channel-number
(Optional) Type and number of the interface that you want to display.
Command Default
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the show interface counters errors command to display interface error counters. If you do not specify an interface, this command displays information about all Layer 2 interfaces.
This command does not require a license.
Examples
This example shows how to display the interface error counters:
switch# show interface counters errors--------------------------------------------------------------------------------Port Align-Err FCS-Err Xmit-Err Rcv-Err UnderSize OutDiscards--------------------------------------------------------------------------------mgmt0 -- -- -- -- -- --Eth2/1 0 0 0 0 0 0Eth2/2 0 0 0 0 0 0Eth2/3 0 0 0 0 0 0Eth2/4 0 0 0 0 0 0Eth2/5 0 0 0 0 0 0Eth2/6 0 0 0 0 0 0Eth2/7 0 0 0 0 0 0Eth2/8 0 0 0 0 0 0Eth2/9 0 0 0 0 0 0Eth2/10 0 0 0 0 0 0Eth2/11 0 0 0 0 0 0Eth2/12 0 0 0 0 0 0Eth2/13 0 0 0 0 0 0Eth2/14 0 0 0 0 0 0Eth2/15 0 0 0 0 0 0Eth2/16 0 0 0 0 0 0Eth2/17 0 0 0 0 0 0Eth2/18 0 0 0 0 0 0Eth2/19 0 0 0 0 0 0Eth2/20 0 0 0 0 0 0Eth2/21 0 0 0 0 0 0Eth2/22 0 0 0 0 0 0Eth2/23 0 0 0 0 0 0Eth2/24 0 0 0 0 0 0Eth2/25 0 0 0 0 0 0Eth2/26 0 0 0 0 0 0Eth2/27 0 0 0 0 0 0Eth2/28 0 0 0 0 0 0Eth2/29 0 0 0 0 0 0Eth2/30 0 0 0 0 0 0Eth2/31 0 0 0 0 0 0Eth2/32 0 0 0 0 0 0Eth2/33 0 0 0 0 0 0Eth2/34 0 0 0 0 0 0Eth2/35 0 0 0 0 0 0Eth2/36 0 0 0 0 0 0Eth2/37 0 0 0 0 0 0Eth2/38 0 0 0 0 0 0Eth2/39 0 0 0 0 0 0Eth2/40 0 0 0 0 0 0Eth2/41 0 0 0 0 0 0Eth2/42 0 0 0 0 0 0Eth2/43 0 0 0 0 0 0Eth2/44 0 0 0 0 0 0Eth2/45 0 0 0 0 0 0Eth2/46 0 0 0 0 0 0Eth2/47 0 0 0 0 0 0Eth2/48 0 0 0 0 0 0--------------------------------------------------------------------------------Port Single-Col Multi-Col Late-Col Exces-Col Carri-Sen Runts--------------------------------------------------------------------------------mgmt0 -- -- -- -- -- --Eth2/1 0 0 0 0 0 0Eth2/2 0 0 0 0 0 0Eth2/3 0 0 0 0 0 0Eth2/4 0 0 0 0 0 0Eth2/5 0 0 0 0 0 0Eth2/6 0 0 0 0 0 0Eth2/7 0 0 0 0 0 0Eth2/8 0 0 0 0 0 0Eth2/9 0 0 0 0 0 0Eth2/10 0 0 0 0 0 0Eth2/11 0 0 0 0 0 0Eth2/12 0 0 0 0 0 0Eth2/13 0 0 0 0 0 0Eth2/14 0 0 0 0 0 0Eth2/15 0 0 0 0 0 0Eth2/16 0 0 0 0 0 0Eth2/17 0 0 0 0 0 0Eth2/18 0 0 0 0 0 0Eth2/19 0 0 0 0 0 0Eth2/20 0 0 0 0 0 0Eth2/21 0 0 0 0 0 0Eth2/22 0 0 0 0 0 0Eth2/23 0 0 0 0 0 0Eth2/24 0 0 0 0 0 0Eth2/25 0 0 0 0 0 0Eth2/26 0 0 0 0 0 0Eth2/27 0 0 0 0 0 0Eth2/28 0 0 0 0 0 0Eth2/29 0 0 0 0 0 0Eth2/30 0 0 0 0 0 0Eth2/31 0 0 0 0 0 0Eth2/32 0 0 0 0 0 0Eth2/33 0 0 0 0 0 0Eth2/34 0 0 0 0 0 0Eth2/35 0 0 0 0 0 0Eth2/36 0 0 0 0 0 0Eth2/37 0 0 0 0 0 0Eth2/38 0 0 0 0 0 0Eth2/39 0 0 0 0 0 0Eth2/40 0 0 0 0 0 0Eth2/41 0 0 0 0 0 0Eth2/42 0 0 0 0 0 0Eth2/43 0 0 0 0 0 0Eth2/44 0 0 0 0 0 0Eth2/45 0 0 0 0 0 0Eth2/46 0 0 0 0 0 0Eth2/47 0 0 0 0 0 0Eth2/48 0 0 0 0 0 0--------------------------------------------------------------------------------Port Giants SQETest-Err Deferred-Tx IntMacTx-Er IntMacRx-Er Symbol-Err--------------------------------------------------------------------------------mgmt0 -- -- -- -- -- --Eth2/1 0 -- 0 0 0 0Eth2/2 0 -- 0 0 0 0Eth2/3 0 -- 0 0 0 0Eth2/4 0 -- 0 0 0 0Eth2/5 0 -- 0 0 0 0Eth2/6 0 -- 0 0 0 0Eth2/7 0 -- 0 0 0 0Eth2/8 0 -- 0 0 0 0Eth2/9 0 -- 0 0 0 0Eth2/10 0 -- 0 0 0 0Eth2/11 0 -- 0 0 0 0Eth2/12 0 -- 0 0 0 0Eth2/13 0 -- 0 0 0 0Eth2/14 0 -- 0 0 0 0Eth2/15 0 -- 0 0 0 0Eth2/16 0 -- 0 0 0 0Eth2/17 0 -- 0 0 0 0Eth2/18 0 -- 0 0 0 0Eth2/19 0 -- 0 0 0 0Eth2/20 0 -- 0 0 0 0Eth2/21 0 -- 0 0 0 0Eth2/22 0 -- 0 0 0 0Eth2/23 0 -- 0 0 0 0Eth2/24 0 -- 0 0 0 0Eth2/25 0 -- 0 0 0 0Eth2/26 0 -- 0 0 0 0Eth2/27 0 -- 0 0 0 0Eth2/28 0 -- 0 0 0 0Eth2/29 0 -- 0 0 0 0Eth2/30 0 -- 0 0 0 0Eth2/31 0 -- 0 0 0 0Eth2/32 0 -- 0 0 0 0Eth2/33 0 -- 0 0 0 0Eth2/34 0 -- 0 0 0 0Eth2/35 0 -- 0 0 0 0Eth2/36 0 -- 0 0 0 0Eth2/37 0 -- 0 0 0 0Eth2/38 0 -- 0 0 0 0Eth2/39 0 -- 0 0 0 0Eth2/40 0 -- 0 0 0 0Eth2/41 0 -- 0 0 0 0Eth2/42 0 -- 0 0 0 0Eth2/43 0 -- 0 0 0 0Eth2/44 0 -- 0 0 0 0Eth2/45 0 -- 0 0 0 0Eth2/46 0 -- 0 0 0 0Eth2/47 0 -- 0 0 0 0Eth2/48 0 -- 0 0 0 0Related Commands
show interface counters storm-control
To display interface storm control discard counters, use the show interface counters storm-control.
show interface [ethernet slot/port | port-channel channel-number] counters storm-control
Syntax Description
ethernet slot/port | port-channel channel-number
(Optional) Type and number of the interface that you want to display
Command Default
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the show interface counters storm-control command to display interface storm control discard counters. If you do not specify an interface, this command displays information about all Layer 2 interfaces.
This command does not require a license.
Examples
This example shows how to display the interface storm control discard counters:
switch# show interface counters storm-control--------------------------------------------------------------------------------Port UcastSupp % McastSupp % BcastSupp % TotalSuppDiscards--------------------------------------------------------------------------------Eth2/1 100.00 100.00 100.00 0Eth2/2 100.00 100.00 100.00 0Eth2/3 100.00 100.00 100.00 0Eth2/4 100.00 100.00 100.00 0Eth2/5 100.00 100.00 100.00 0Eth2/6 100.00 100.00 100.00 0Eth2/7 100.00 100.00 100.00 0Eth2/8 100.00 100.00 100.00 0Eth2/9 100.00 100.00 100.00 0Eth2/10 100.00 100.00 100.00 0Eth2/11 100.00 100.00 100.00 0Eth2/12 100.00 100.00 100.00 0Eth2/13 100.00 100.00 100.00 0Eth2/14 100.00 100.00 100.00 0Eth2/15 100.00 100.00 100.00 0Eth2/16 100.00 100.00 100.00 0Eth2/17 100.00 100.00 100.00 0Eth2/18 100.00 100.00 100.00 0Eth2/19 100.00 100.00 100.00 0Eth2/20 100.00 100.00 100.00 0Eth2/21 100.00 100.00 100.00 0Eth2/22 100.00 100.00 100.00 0Eth2/23 100.00 100.00 100.00 0Eth2/24 100.00 100.00 100.00 0Eth2/25 100.00 100.00 100.00 0Eth2/26 100.00 100.00 100.00 0Eth2/27 100.00 100.00 100.00 0Eth2/28 100.00 100.00 100.00 0Eth2/29 100.00 100.00 100.00 0Eth2/30 100.00 100.00 100.00 0Eth2/31 100.00 100.00 100.00 0Eth2/32 100.00 100.00 100.00 0Eth2/33 100.00 100.00 100.00 0Eth2/34 100.00 100.00 100.00 0Eth2/35 100.00 100.00 100.00 0Eth2/36 100.00 100.00 100.00 0Eth2/37 100.00 100.00 100.00 0Eth2/38 100.00 100.00 100.00 0Eth2/39 100.00 100.00 100.00 0Eth2/40 100.00 100.00 100.00 0Eth2/41 100.00 100.00 100.00 0Eth2/42 100.00 100.00 100.00 0Eth2/43 100.00 100.00 100.00 0Eth2/44 100.00 100.00 100.00 0Eth2/45 100.00 100.00 100.00 0Eth2/46 100.00 100.00 100.00 0Eth2/47 100.00 100.00 100.00 0Eth2/48 100.00 100.00 100.00 0Related Commands
show interface counters trunk
To display the counters for Layer 2 switch port trunk interfaces, use the show interface counters trunk command.
show interface {ethernet slot/port} counters trunk
Syntax Description
ethernet slot/port
Specifies the module number and port number for the trunk interface that you want to display.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
The device supports only IEEE 802.1Q encapsulation. This command also displays the counters for trunk port channels.
This command does not require a license.
Examples
This example shows how to display the counters for a trunk interface. This display shows the frames transmitted and received through the trunk interface, as well as the number of frames with the wrong trunk encapsulation:
switch# show interface ethernet 2/9 counters trunk---------------------------------------------------------------------Port TrunkFramesTx TrunkFramesRx WrongEncap---------------------------------------------------------------------Ethernet2/9 0 0 0Related Commands
show interface debounce
To display the debounce time information about the interface, use the show interface debounce command.
show interface [ethernet slot/port | port-channel channel-number] debounce
Syntax Description
ethernet slot/port | port-channel channel-number
(Optional) Type and number of the interface that you want to display
Command Default
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the show interface debounce command to display debounce time information about the interface. If you do not specify an interface, this command displays information about all Layer 2 interfaces.
This command does not require a license.
Examples
This example shows how to display debounce time information about the interface:
switch# show interface debounce--------------------------------------------------------------------------------Port Debounce time Value(ms)--------------------------------------------------------------------------------Eth2/1 enable 100Eth2/2 enable 100Eth2/3 enable 100Eth2/4 enable 100Eth2/5 enable 100Eth2/6 enable 100Eth2/7 enable 100Eth2/8 enable 100Eth2/9 enable 100Eth2/10 enable 100Eth2/11 enable 100Eth2/12 enable 100Eth2/13 enable 100Eth2/14 enable 100Eth2/15 enable 100Eth2/16 enable 100Eth2/17 enable 100Eth2/18 enable 100Eth2/19 enable 100Eth2/20 enable 100Eth2/21 enable 100Eth2/22 enable 100Eth2/23 enable 100Eth2/24 enable 100Eth2/25 enable 100Eth2/26 enable 100Eth2/27 enable 100Eth2/28 enable 100Eth2/29 enable 100Eth2/30 enable 100Eth2/31 enable 100Eth2/32 enable 100Eth2/33 enable 100Eth2/34 enable 100Eth2/35 enable 100Eth2/36 enable 100Eth2/37 enable 100Eth2/38 enable 100Eth2/39 enable 100Eth2/40 enable 100Eth2/41 enable 100Eth2/42 enable 100Eth2/43 enable 100Eth2/44 enable 100Eth2/45 enable 100Eth2/46 enable 100Eth2/47 enable 100Eth2/48 enable 100Related Commands
show interface description
To display a description about the interface, use the show interface description command.
show interface description
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the show interface description command to display the interface description.
This command does not require a license.
Examples
This example shows how to display a description of the interface:
switch# show interface description-------------------------------------------------------------------------------Interface Description-------------------------------------------------------------------------------mgmt0 ---------------------------------------------------------------------------------Port Type Speed Description-------------------------------------------------------------------------------Eth2/1 eth 1000 --Eth2/2 eth 1000 --Eth2/3 eth 1000 --Eth2/4 eth 1000 --Eth2/5 eth 1000 --Eth2/6 eth 1000 --Eth2/7 eth 1000 server2Eth2/8 eth 1000 --Eth2/9 eth 1000 --Eth2/10 eth 1000 ethernet slot 2 port 10Eth2/11 eth 1000 --Eth2/12 eth 1000 --Eth2/13 eth 1000 --Eth2/14 eth 1000 --Eth2/15 eth 1000 --Eth2/16 eth 1000 --Eth2/17 eth 1000 --Eth2/18 eth 1000 --Eth2/19 eth 1000 --Eth2/20 eth 1000 --Eth2/21 eth 1000 --Eth2/22 eth 1000 --Eth2/23 eth 1000 --Eth2/24 eth 1000 --Eth2/25 eth 1000 --Eth2/26 eth 1000 --Eth2/27 eth 1000 --Eth2/28 eth 1000 --Eth2/29 eth 1000 --Eth2/30 eth 1000 --Eth2/31 eth 1000 --Eth2/32 eth 1000 --Eth2/33 eth 1000 --...<additional lines truncated>Related Commands
show interface ethernet
To display information about the Ethernet interface, use the show interface ethernet command.
show interface ethernet slot/port
Syntax Description
Command Default
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the show interface ethernet command to display information about the Ethernet interface.
This command does not require a license.
Examples
This example shows how to display information about the Ethernet interface:
switch# show interface ethernet 2/5Ethernet2/5 is down (Administratively down)Hardware: 10/100/1000 Ethernet, address: 0018.bad8.3ffd (bia 0019.076c.4db0)MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,reliability 255/255, txload 1/255, rxload 1/255Encapsulation ARPAauto-duplex, auto-speedBeacon is turned offAuto-Negotiation is turned onInput flow-control is off, output flow-control is offAuto-mdix is turned onSwitchport monitor is offLast clearing of "show interface" counters never1 minute input rate 0 bits/sec, 0 packets/sec1 minute output rate 0 bits/sec, 0 packets/secL3 in Switched:ucast: 0 pkts, 0 bytes - mcast: 0 pkts, 0 bytesL3 out Switched:ucast: 0 pkts, 0 bytes - mcast: 0 pkts, 0 bytesRx0 input packets 0 unicast packets 0 multicast packets0 broadcast packets 0 jumbo packets 0 storm suppression packets0 bytesTx0 output packets 0 multicast packets0 broadcast packets 0 jumbo packets0 bytes0 input error 0 short frame 0 watchdog0 no buffer 0 runt 0 CRC 0 ecc0 overrun 0 underrun 0 ignored 0 bad etype drop0 bad proto drop 0 if down drop 0 input with dribble0 input discard0 output error 0 collision 0 deferred0 late collision 0 lost carrier 0 no carrier0 babble0 Rx pause 0 Tx pause0 interface resetsRelated Commands
interface
Enters the interface configuration mode, and configures the types and identities of interfaces.
show interface flowcontrol
To display the flowcontrol configuration for all or a specified interface, use the show interface flowcontrol command.
show interface [ethernet slot/port | port-channel channel-number] flowcontrol
Syntax Description
ethernet slot/port | port-channel channel-number
(Optional) Type and number of the interface that you want to display
Command Default
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin 2
vdc-adminCommand History
Usage Guidelines
Use the show interface flowcontrol command to display information about the interface flowcontrol. If you do not specify an interface, this command displays information about all Layer 2 interfaces.
This command does not require a license.
Examples
This example shows how to display the interface flow control information:
switch# show interface flowcontrol--------------------------------------------------------------------------------Port Send FlowControl Receive FlowControl RxPause TxPauseadmin oper admin oper--------------------------------------------------------------------------------Eth2/1 off off off off 0 0Eth2/2 off off off off 0 0Eth2/3 off off off off 0 0Eth2/4 off off off off 0 0Eth2/5 off off off off 0 0Eth2/6 off off off off 0 0Eth2/7 off off off off 0 0Eth2/8 off off off off 0 0Eth2/9 off off off off 0 0Eth2/10 off off off off 0 0Eth2/11 off off off off 0 0Eth2/12 off off off off 0 0Eth2/13 off off off off 0 0Eth2/14 off off off off 0 0Eth2/15 off off off off 0 0Eth2/16 off off off off 0 0Eth2/17 off off off off 0 0Eth2/18 off off off off 0 0Eth2/19 off off off off 0 0Eth2/20 off off off off 0 0Eth2/21 off off off off 0 0Eth2/22 off off off off 0 0Eth2/23 off off off off 0 0Eth2/24 off off off off 0 0Eth2/25 off off off off 0 0Eth2/26 off off off off 0 0Eth2/27 off off off off 0 0Eth2/28 off off off off 0 0Eth2/29 off off off off 0 0Eth2/30 off off off off 0 0Eth2/31 off off off off 0 0Eth2/32 off off off off 0 0Eth2/33 off off off off 0 0Eth2/34 off off off off 0 0Eth2/35 off off off off 0 0Eth2/36 off off off off 0 0Eth2/37 off off off off 0 0Eth2/38 off off off off 0 0Eth2/39 off off off off 0 0Eth2/40 off off off off 0 0Eth2/41 off off off off 0 0Eth2/42 off off off off 0 0Eth2/43 off off off off 0 0Eth2/44 off off off off 0 0Eth2/45 off off off off 0 0Eth2/46 off off off off 0 0Eth2/47 off off off off 0 0Eth2/48 off off off off 0 0Related Commands
flowcontrol
Enables or disables the ability of the Ethernet port to send and receive flow-control pause frames.
show interface mgmt
To display the management interface information, use the show interface mgmt command.
show interface mgmt number [brief | counters [detailed [all] | errors [snmp]] | description | status]
Syntax Description
Command Default
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the show interface mgmt number command to display information about the management interface.
This command does not require a license.
Examples
This example shows how to display the management interface information:
switch# show interface mgmt0mgmt0 is upHardware: GigabitEthernet, address: 0019.076c.1a78 (bia 0019.076c.1a78)Internet Address is 172.28.231.193/23MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,reliability 255/255, txload 1/255, rxload 1/255Encapsulation ARPAfull-duplex, 1000 Mb/sAuto-Negotiation is turned on1 minute input rate 6446522 bits/sec, 78642 packets/sec1 minute output rate 1965455 bits/sec, 20644 packets/secRx78681 input packets 15607 unicast packets 20178 multicast packets42896 broadcast packets 24189392 bytesTx20647 output packets 20377 unicast packets 246 multicast packets24 broadcast packets 7370904 bytesRelated Commands
interface
Enters the interface configuration mode, and configures the types and identities of interfaces.
show interface port-channel
To display descriptive information about port channels, use the show interface port-channel command.
show interface port-channel channel-number [brief | description | flowcontrol | status | switchport | trunk]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
4.0
This command was introduced.
4.2(1)
Display of configured static MAC address for Layer 3 port channels added.
Usage Guidelines
To display more statistics for the specified port channels, use the show interface port-channel counters command.
This command does not require a license.
Examples
This example shows how to display information for a specific port channel. This command displays statistical information gathered on the port channel at 1-minute intervals:
switch(config)# show interface port-channel 50port-channel50 is down (No operational members)Hardware is Port-Channel, address is 0000.0000.0000 (bia 0000.0000.0000)MTU 1500 bytes, BW 100000 Kbit, DLY 10 usec,reliability 255/255, txload 1/255, rxload 1/255Encapsulation ARPAPort mode is accessauto-duplex, auto-speedBeacon is turned offInput flow-control is off, output flow-control is offSwitchport monitor is offMembers in this channel: Eth2/10Last clearing of "show interface" counters 2d71.2uh1 minute input rate 0 bytes/sec, 0 packets/sec1 minute output rate 0 bytes/sec, 0 packets/secRx0 input packets 0 unicast packets 0 multicast packets0 broadcast packets 0 jumbo packets 0 storm suppression packets0 bytesTx0 output packets 0 multicast packets0 broadcast packets 0 jumbo packets0 bytes0 input error 0 short frame 0 watchdog0 no buffer 0 runt 0 CRC 0 ecc0 overrun 0 underrun 0 ignored 0 bad etype drop0 bad proto drop 0 if down drop 0 input with dribble0 input discard0 output error 0 collision 0 deferred0 late collision 0 lost carrier 0 no carrier0 babble0 Rx pause 0 Tx pause 0 resetThis example shows how to display a brief description for a specific port channel, including the mode for the port channel, the status, speed, and protocol:
switch# show interface port-channel 5 brief--------------------------------------------------------------------------------Port-channel VLAN Type Mode Status Reason Speed ProtocolInterface--------------------------------------------------------------------------------eth access down No operational members auto(D) lacpThis example shows how to display the description for a specific port channel:
switch# show interface port-channel 5 description-------------------------------------------------------------------------------Interface Description-------------------------------------------------------------------------------port-channel5 testThis example shows how to display the flow-control information for a specific port channel:
switch# show interface port-channel 50 flowcontrol------------------------------------------------------------------------------Port Send FlowControl Receive FlowControl RxPause TxPauseadmin oper admin oper------------------------------------------------------------------------------Po50 off off off off 0 0The oper display for the show interface port-channel flowcontrol command shows as on if one member of the port channel is set to on for flow control; then all the of the members and the entire port channel is set to on for flow control.
This example shows how to display the status of a specific port channel:
switch# show interface port-channel 5 status--------------------------------------------------------------------------------Port Name Status Vlan Duplex Speed Type--------------------------------------------------------------------------------test down 1 auto auto --This example shows how to display information for a specific Layer 2 port channel:
switch# show interface port-channel 50 switchportName: port-channel50Switchport: EnabledSwitchport Monitor: Not enabledOperational Mode: trunkAccess Mode VLAN: 1 (default)Trunking Native Mode VLAN: 1 (default)Trunking VLANs Enabled: 1-3967,4048-4093Administrative private-vlan primary host-association: noneAdministrative private-vlan secondary host-association: noneAdministrative private-vlan primary mapping: noneAdministrative private-vlan secondary mapping: noneAdministrative private-vlan trunk native VLAN: noneAdministrative private-vlan trunk encapsulation: dot1qAdministrative private-vlan trunk normal VLANs: noneAdministrative private-vlan trunk private VLANs: noneOperational private-vlan: noneThis command displays information for Layer 2 port channels in both the access and trunk modes.
When you use this command for a routed port channel, the device returns the following message:
Name: port-channel20Switchport: DisabledThis example shows how to display information for a specific Layer 2 port channel that is in trunk mode:
switch# show interface port-channel 5 trunkswitch# show interface port-channel 50 trunkport-channel50 is down (No operational members)Hardware is Ethernet, address is 0000.0000.0000MTU 1500 bytes, BW 100000 Kbit, DLY 10 usecPort mode is accessSpeed is auto-speedDuplex mode is autoBeacon is turned offReceive flow-control is off, Send flow-control is offRate mode is dedicatedMembers in this channel: Eth2/10Native Vlan: 1Allowed Vlans: 1-3967,4048-4093This command displays information for only Layer 2 port channels in the trunk modes; you cannot display information about Layer 2 port channels in the access mode with this command.
Related Commands
show interface port-channel counters
Displays the statistics for channel groups.
show interface port-channel counters
To display information about port-channel statistics, use the show interface port-channel counters command.
show interface port-channel channel-number counters [brief | detailed [all | snmp] | errors [snmp] | trunk]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
This command displays statistics for all port channels including LACP-enabled port channels and those port channels that are not associated with an aggregation protocol.
This command does not require a license.
Examples
This example shows how to display the counters for a specific port channel. This display shows the transmitted and received unicast and multicast packets:
switch# show interface port-channel 2 countersPort InOctets InUcastPkts InMcastPkts InBcastPktsPo2 6007 1 31 1Port OutOctets OutUcastPkts OutMcastPkts OutBcastPktsPo2 4428 1 25 1This example shows how to display the brief counters for a specific port channel. This display shows the transmitted and received rate and total frames:
switch# show interface port-channel 20 counters brief-------------------------------------------------------------------------------Interface Input (rate is 1 min avg) Output (rate is 1 min avg)------------------------- -----------------------------Rate Total Rate TotalMB/s Frames MB/s Frames-------------------------------------------------------------------------------port-channel20 0 0 0 0This example shows how to display all the detailed counters for a specific port channel:
switch# show interface port-channel 20 counters detailed allport-channel2064 bit counters:0. rxHCTotalPkts = 01. txHCTotalPks = 02. rxHCUnicastPkts = 03. txHCUnicastPkts = 04. rxHCMulticastPkts = 05. txHCMulticastPkts = 06. rxHCBroadcastPkts = 07. txHCBroadcastPkts = 08. rxHCOctets = 09. txHCOctets = 010. rxTxHCPkts64Octets = 011. rxTxHCpkts65to127Octets = 012. rxTxHCpkts128to255Octets = 013. rxTxHCpkts256to511Octets = 014. rxTxHCpkts512to1023Octets = 015. rxTxHCpkts1024to1518Octets = 016. rxTxHCpkts1519to1548Octets = 017. rxHCTrunkFrames = 018. txHCTrunkFrames = 019. rxHCDropEvents = 0All Port Counters:0. InPackets = 01. InOctets = 02. InUcastPkts = 03. InMcastPkts = 04. InBcastPkts = 05. InJumboPkts = 06. StormSuppressPkts = 07. OutPackets = 08. OutOctets = 09. OutUcastPkts = 010. OutMcastPkts = 011. OutBcastPkts = 012. OutJumboPkts = 013. rxHCPkts64Octets = 014. rxHCPkts65to127Octets = 015. rxHCPkts128to255Octets = 016. rxHCPkts256to511Octets = 017. rxHCpkts512to1023Octets = 018. rxHCpkts1024to1518Octets = 019. rxHCpkts1519to1548Octets = 020. txHCPkts64Octets = 021. txHCPkts65to127Octets = 022. txHCPkts128to255Octets = 023. txHCPkts256to511Octets = 024. txHCpkts512to1023Octets = 025. txHCpkts1024to1518Octets = 026. txHCpkts1519to1548Octets = 027. ShortFrames = 028. Collisions = 029. SingleCol = 030. MultiCol = 031. LateCol = 032. ExcessiveCol = 033. LostCarrier = 034. NoCarrier = 035. Runts = 036. Giants = 037. InErrors = 038. OutErrors = 039. InputDiscards = 040. BadEtypeDrops = 041. IfDownDrops = 042. InUnknownProtos = 043. txCRC = 044. rxCRC = 045. Symbol = 046. txDropped = 047. TrunkFramesTx = 048. TrunkFramesRx = 049. WrongEncap = 050. Babbles = 051. Watchdogs = 052. ECC = 053. Overruns = 054. Underruns = 055. Dribbles = 056. Deferred = 057. Jabbers = 058. NoBuffer = 059. Ignored = 060. bpduOutLost = 061. cos0OutLost = 062. cos1OutLost = 063. cos2OutLost = 064. cos3OutLost = 065. cos4OutLost = 066. cos5OutLost = 067. cos6OutLost = 068. cos7OutLost = 069. RxPause = 070. TxPause = 071. Resets = 072. SQETest = 073. InLayer3Routed = 074. InLayer3RoutedOctets = 075. OutLayer3Routed = 076. OutLayer3RoutedOctets = 077. OutLayer3Unicast = 078. OutLayer3UnicastOctets = 079. OutLayer3Multicast = 080. OutLayer3MulticastOctets = 081. InLayer3Unicast = 082. InLayer3UnicastOctets = 083. InLayer3Multicast = 084. InLayer3MulticastOctets = 085. InLayer3AverageOctets = 086. InLayer3AveragePackets = 087. OutLayer3AverageOctets = 088. OutLayer3AveragePackets = 0This example shows how to display the error counters for a specific port channel:
switch# show interface port-channel 5 counters errors--------------------------------------------------------------------------------Port Align-Err FCS-Err Xmit-Err Rcv-Err UnderSize OutDiscards--------------------------------------------------------------------------------Po5 0 0 0 0 0 0--------------------------------------------------------------------------------Port Single-Col Multi-Col Late-Col Exces-Col Carri-Sen Runts--------------------------------------------------------------------------------Po5 0 0 0 0 0 0--------------------------------------------------------------------------------Port Giants SQETest-Err Deferred-Tx IntMacTx-Er IntMacRx-Er Symbol-Err--------------------------------------------------------------------------------0 -- 0 0 0 0This example shows how to display information about the trunk interfaces for a specific port channel:
switch# show interface port-channel 5 counters trunk-------------------------------------------------------------------------------Port TrunkFramesTx TrunkFramesRx WrongEncap-------------------------------------------------------------------------------port-channel5 0 0 0Related Commands
clear counters interface port-channel channel-number
Clears the statistics for all interfaces that belong to a specific channel group.
show interface status
To display the interface line status, use the show interface status command.
show interface status [down | err-disabled | err-vlans | inactive | module number | up]
Syntax Description
Command Default
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the show interface status to display the interface line status.
This command does not require a license.
Examples
This example shows how to display the interface status for a specific module:
switch# show interface status module 2--------------------------------------------------------------------------------Port Name Status Vlan Duplex Speed Type--------------------------------------------------------------------------------Eth2/1 -- down routed auto auto 1000BaseTEth2/2 -- down routed auto auto 1000BaseTEth2/3 -- down routed auto auto 1000BaseTEth2/4 -- down 1 auto auto 1000BaseTEth2/5 -- down routed auto auto 1000BaseTEth2/6 -- down 1 auto auto 1000BaseTEth2/7 server2 up 1 full 1000 1000BaseTEth2/8 -- down routed auto auto 1000BaseTEth2/9 -- up 1 full 1000 1000BaseTEth2/10 ethernet slot 2 po down 1 auto auto 1000BaseTEth2/11 -- down routed auto auto 1000BaseTEth2/12 -- down routed auto auto 1000BaseTEth2/13 -- down routed auto auto 1000BaseTEth2/14 -- down routed auto auto 1000BaseTEth2/15 -- down routed auto auto 1000BaseTEth2/16 -- down routed auto auto 1000BaseTEth2/17 -- down routed auto auto 1000BaseTEth2/18 -- down routed auto auto 1000BaseTEth2/19 -- down routed auto auto 1000BaseTEth2/20 -- down routed auto auto 1000BaseTEth2/21 -- down routed auto auto 1000BaseTEth2/22 -- down routed auto auto 1000BaseTEth2/23 -- down routed auto auto 1000BaseTEth2/24 -- down routed auto auto 1000BaseTEth2/25 -- down routed auto auto 1000BaseTEth2/26 -- down routed auto auto 1000BaseTEth2/27 -- down routed auto auto 1000BaseTEth2/28 -- down routed auto auto 1000BaseTEth2/29 -- down routed auto auto 1000BaseTEth2/30 -- down routed auto auto 1000BaseTEth2/31 -- down routed auto auto 1000BaseTEth2/32 -- down routed auto auto 1000BaseTEth2/33 -- down routed auto auto 1000BaseTEth2/34 -- down routed auto auto 1000BaseTEth2/35 -- down routed auto auto 1000BaseTEth2/36 -- down routed auto auto 1000BaseTEth2/37 -- down routed auto auto 1000BaseTEth2/38 -- down routed auto auto 1000BaseTEth2/39 -- down routed auto auto 1000BaseTEth2/40 -- down routed auto auto 1000BaseTEth2/41 -- down routed auto auto 1000BaseTEth2/42 -- down routed auto auto 1000BaseTEth2/43 -- down routed auto auto 1000BaseTEth2/44 -- down routed auto auto 1000BaseTEth2/45 -- down routed auto auto 1000BaseTEth2/46 -- down routed auto auto 1000BaseTEth2/47 -- down routed auto auto 1000BaseTEth2/48 -- down routed auto auto 1000BaseTRelated Commands
interface
Enters the interface configuration mode, and configures the types and identities of interfaces.
show interface switchport
To display information about all the switch port interfaces, use the show interface switchport command.
show interface [ethernet type/slot | port-channel channel-number] switchport
Syntax Description
ethernet type/slot | port- channel channel-number
(Optional) Type and number of the interface that you want to display.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
4.0
This command was introduced.
4.2(1)
Information about private VLAN promiscuous trunk ports was added.
Usage Guidelines
If you do not specify an interface, this command displays information about all Layer 2 interfaces, including access, trunk, and port-channel interfaces and all private VLAN ports.
Use the show interface counters command to display statistics for the specified Layer 2 interface.
This command does not require a license.
Examples
This example shows how to display information for all Layer 2 interfaces:
switch# show interface switchportName: Ethernet2/5Switchport: EnabledSwitchport Monitor: Not enabledOperational Mode: accessAccess Mode VLAN: 1 (default)Trunking Native Mode VLAN: 1 (default)Trunking VLANs Enabled: 1-3967,4048-4093Administrative private-vlan primary host-association: noneAdministrative private-vlan secondary host-association: noneAdministrative private-vlan primary mapping: noneAdministrative private-vlan secondary mapping: noneAdministrative private-vlan trunk native VLAN: noneAdministrative private-vlan trunk encapsulation: dot1qAdministrative private-vlan trunk normal VLANs: noneAdministrative private-vlan trunk private VLANs: noneOperational private-vlan: noneName: Ethernet2/9Switchport: EnabledSwitchport Monitor: Not enabledOperational Mode: trunkAccess Mode VLAN: 1 (default)Trunking Native Mode VLAN: 1 (default)Trunking VLANs Enabled: 1-3967,4048-4093Administrative private-vlan primary host-association: noneAdministrative private-vlan secondary host-association: noneAdministrative private-vlan primary mapping: noneAdministrative private-vlan secondary mapping: noneAdministrative private-vlan trunk native VLAN: noneAdministrative private-vlan trunk encapsulation: dot1qAdministrative private-vlan trunk normal VLANs: noneAdministrative private-vlan trunk private VLANs: noneOperational private-vlan: noneName: port-channel5Switchport: EnabledSwitchport Monitor: Not enabledOperational Mode: accessAccess Mode VLAN: 1 (default)Trunking Native Mode VLAN: 1 (default)Trunking VLANs Enabled: 1-3967,4048-4093Administrative private-vlan primary host-association: noneAdministrative private-vlan secondary host-association: noneAdministrative private-vlan primary mapping: noneAdministrative private-vlan secondary mapping: noneAdministrative private-vlan trunk native VLAN: noneAdministrative private-vlan trunk encapsulation: dot1qAdministrative private-vlan trunk normal VLANs: noneAdministrative private-vlan trunk private VLANs: noneOperational private-vlan: noneBeginning with Cisco NX-OS Release 4.2(1), you can display information on private VLAN promiscuous trunk ports on Cisco Nexus 7000 Series devices. This example shows how to display information for those interfaces:
switch# show interface switchportName: Ethernet7/4Switchport: EnabledAdministrative Mode: private-vlan trunk promiscuousOperational Mode: downAdministrative Trunking Encapsulation: negotiateNegotiation of Trunking: onAccess Mode VLAN: 1 (default)Trunking Native Mode VLAN: 1 (default)Administrative Native VLAN tagging: enabledVoice VLAN: noneAdministrative private-vlan host-association: noneAdministrative private-vlan mapping: noneAdministrative private-vlan secondary mapping: noneAdministrative private-vlan trunk Native VLAN tagging: enabledAdministrative private-vlan trunk encapsulation: dot1qAdministrative private-vlan trunk normal VLANs: 1, 4, 3000-4000Administrative private-vlan trunk private VLAN mappings:2 (VLAN0002) 3 (VLAN0003) 4 (VLAN0004) 5 (VLAN00005)10 (VLAN0010) 20 (CLAN0020) 30 (VLAN0030) 40 (Inactive)Operational private-vlan: noneRelated Commands
switchport mode
Sets the specified interfaces as either Layer 2 access or trunk interfaces.
show interface transceiver
To display the interface transceiver information, use the show interface transceiver command.
show interface transceiver [calibrations | details]
Syntax Description
calibrations
(Optional) Show interface transceiver calibrations
details
(Optional) Show interface transceiver details
Command Default
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the show interface transceiver [calibrations | details] to display the interface line status.
This command does not require a license.
Examples
This example shows how to display the interface transceiver calibrations:
switch# show interface transceiver calibrationsEthernet2/1sfp is not applicableEthernet2/2sfp is not applicableEthernet2/3sfp is not applicableEthernet2/4sfp is not applicableEthernet2/5sfp is not applicable...<additional lines truncated>Related Commands
interface
Enters the interface configuration mode, and configures the types and identities of interfaces.
show interface transceiver
To display information about all the transceiver interfaces, use the show interface transceiver command.
show interface transceiver [calibrations | details]
Syntax Description
calibrations
(Optional) Displays calibration information for transceivers.
detail
(Optional) Displays detailed information for transceivers.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display calibration information for transceiver interfaces:
switch(config)# show interface transceiver calibrationsEthernet9/25sfp is presentname is CISCO-EXCELIGHTpart number is SPP5101LR-C1revision is Aserial number is ECL121601PBnominal bitrate is 10300 MBits/secLink length supported for 9/125um fiber is 10 km(s)cisco id is --cisco extended id number is 4SFP External Calibrations Information----------------------------------------------------------------------Slope Offset Rx4/Rx3/Rx2/Rx1/Rx0----------------------------------------------------------------------Temperature 0 0Voltage 0 0Current 0 0Tx Power 0 0Rx Power 0.0000/0.0000/0.0000/0.0000/0.0000This example shows how to display detailed information for transceiver interfaces:
switch(config)# show interface transceiver detailedEthernet10/9sfp is presentname is CISCOpart number is SPP5101SR-C1revision is Aserial number is ECL1120017Jnominal bitrate is 10300 MBits/secLink length supported for 50/125um fiber is 82 m(s)Link length supported for 62.5/125um fiber is 26 m(s)cisco id is --cisco extended id number is 4SFP Detail Diagnostics Information (external calibration)----------------------------------------------------------------------------Alarms WarningsHigh Low High Low----------------------------------------------------------------------------Temperature 25.54 C 75.00 C -5.00 C 70.00 C 0.00 CVoltage 3.22 V 3.63 V 2.97 V 3.46 V 3.13 VCurrent 4.49 mA 10.00 mA 0.00 mA 9.00 mA 0.00 mATx Power -3.50 dBm 2.99 dBm -11.30 dBm -1.00 dBm -7.30 dBmRx Power -2.92 dBm 2.99 dBm -13.97 dBm -1.00 dBm -9.91 dBmTransmit Fault Count = 0----------------------------------------------------------------------------Related Commands
show interface trunk
To display information about all the trunk interfaces, use the show interface trunk command.
show interface [ethernet slot/port | port-channel channel-number] trunk [module number | vlan vlan-id]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
If you do not specify an interface, a module number, or a VLAN number, the system displays information for all trunk interfaces.
This command displays information about all Layer 2 trunk interfaces and trunk port-channel interfaces.
Use the show interface counters command to display statistics for the specified Layer 2 interface.
This command does not require a license.
Examples
This example shows how to display information for all Layer 2 trunk interfaces:
switch(config)# show interface trunk-----------------------------------------------------------------------------Port Native Status PortVlan Channel-----------------------------------------------------------------------------Eth2/9 1 trunking --Eth2/10 1 trnk-bndl Po50Po50 1 not-trunking -------------------------------------------------------------------------------Port Vlans Allowed on Trunk-----------------------------------------------------------------------------Eth2/9 1-3967,4048-4093Eth2/10 1-3967,4048-4093Po50 1-3967,4048-4093-----------------------------------------------------------------------------Port STP Forwarding-----------------------------------------------------------------------------Eth2/9 noneEth2/10 nonePo50 noneRelated Commands
switchport mode trunk
Sets the specified interfaces as Layer 2 trunk interfaces.
show interface tunnel
To display information about the tunnel interfaces, use the show interface tunnel command.
show interface tunnel number
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
4.1(2)
This command was introduced.
4.2(1)
Display of configured static MAC address added.
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information on tunnel interfaces:
switch(config)# show interface tunnel 5Tunnel5 is down (Administratively down)MTU 1476 bytes, BW 9 KbitTransport protocol is in VRF "default"Tunnel protocol/transport GRE/IPLast clearing of "show interface" counters neverTx0 packets output, 1 minute output rate 0 packets/secRx0 packets input, 1 minute input rate 0 packets/secRelated Commands
show lacp counters
To display information about Link Aggregation Control Protocol (LACP) statistics, use the show lacp counters command.
show lacp counters [interface port-channel channel-number]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
If you do not specify the channel-number, all channel groups are displayed.
This command does not require a license.
Examples
This example shows how to display the LACP statistics for a specific channel group:
switch# show lacp counters interface port-channel 1LACPDUs Marker Marker Response LACPDUsPort Sent Recv Sent Recv Sent Recv Pkts Err-----------------------------------------------------------------------------port-channel1Ethernet1/1 554 536 0 0 0 0 0Ethernet1/2 527 514 0 0 0 0 0Ethernet1/3 535 520 0 0 0 0 0Ethernet1/4 515 502 0 0 0 0 0Ethernet1/5 518 505 0 0 0 0 0Ethernet1/6 540 529 0 0 0 0 0Ethernet1/7 541 530 0 0 0 0 0Ethernet1/8 547 532 0 0 0 0 0Ethernet1/9 544 532 0 0 0 0 0Ethernet1/10 513 501 0 0 0 0 0Ethernet1/11 497 485 0 0 0 0 0Ethernet1/12 493 486 0 0 0 0 0Ethernet1/13 492 485 0 0 0 0 0Ethernet1/14 482 481 0 0 0 0 0Ethernet1/15 481 476 0 0 0 0 0Ethernet1/16 482 477 0 0 0 0 0Related Commands
clear lacp counters
Clears the statistics for all LACP interfaces or those interfaces that belong to a specific LACP channel group.
show lacp interface
To display information about specific Link Aggregation Control Protocol (LACP) interfaces, use the show lacp interface command.
show lacp interface ethernet slot/port
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
The LACP_Activity field displays whether the link is configured in the active or passive port-channel mode.
The Port Identifier field displays the port priority as part of the information. The part of the information in this field is the port number. The following example shows how to identify the port priority and the port number:
Port Identifier=0x8000,0x101The port priority value is 0x8000, and the port number value is 0x101 in this example.
This command does not require a license.
Examples
This example shows how to display the LACP statistics for a specific channel group:
switch# show lacp interface ethernet 1/1switch(config-if-range)# show lacp interface eth1/1Interface Ethernet1/1 is upChannel group is 1 port channel is Po1PDUs sent: 556PDUs rcvd: 538Markers sent: 0Markers rcvd: 0Marker response sent: 0Marker response rcvd: 0Unknown packets rcvd: 0Illegal packets rcvd: 0Lag Id: [ [(8000, 0-11-11-22-22-74, 0, 8000, 101), (8000, 0-11-11-22-22-75, 0, 8000, 401)] ]Operational as aggregated link since Wed Jun 11 20:37:59 2008Local Port: Eth1/1 MAC Address= 0-11-11-22-22-74System Identifier=0x8000,0-11-11-22-22-74Port Identifier=0x8000,0x101Operational key=0LACP_Activity=activeLACP_Timeout=Long Timeout (30s)Synchronization=IN_SYNCCollecting=trueDistributing=truePartner information refresh timeout=Long Timeout (90s)Actor Admin State=Actor Oper State=Neighbor: 4/1MAC Address= 0-11-11-22-22-75System Identifier=0x8000,0-11-11-22-22-75Port Identifier=0x8000,0x401Operational key=0LACP_Activity=activeLACP_Timeout=Long Timeout (30s)Synchronization=IN_SYNCCollecting=trueDistributing=truePartner Admin State=Partner Oper State=Related Commands
show lacp neighbor
To display information about Link Aggregation Control Protocol (LACP) neighbors, use the show lacp neighbor command.
show lacp neighbor [interface port-channel channel-number]
Syntax Description
channel-number
Port-channel number for the LACP neighbor that you want to display. The range of values is from 1 to 4096.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
If you do not specify the channel-number, all channel groups are displayed.
This command does not require a license.
Examples
This example shows how to display the information about the LACP neighbors for a specific port channel:
switch# show lacp neighbor interface port-channel 1Flags: S - Device is sending Slow LACPDUs F - Device is sending Fast LACPDUsA - Device is in Active mode P - Device is in Passive modeport-channel1 neighborsPartner's informationPartner Partner PartnerPort System ID Port Number Age FlagsEth1/1 32768,0-11-11-22-22-750x401 44817 SALACP Partner Partner PartnerPort Priority Oper Key Port State32768 0x0 0x3dPartner's informationPartner Partner PartnerPort System ID Port Number Age FlagsEth1/2 32768,0-11-11-22-22-750x402 44817 SALACP Partner Partner PartnerPort Priority Oper Key Port State32768 0x0 0x3dRelated Commands
show lacp port-channel
To display information about Link Aggregation Control Protocol (LACP) port channels, use the show lacp port-channel command.
show lacp port-channel [interface port-channel channel-number]
Syntax Description
channel-number
Port-channel number for the LACP channel group that you want to display. The range of values is from 1 to 4096.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
If you do not specify the channel-number, all channel groups are displayed.
This command does not require a license.
Examples
This example shows how to display the information about LACP port channels:
switch# show lacp port-channelport-channel1Local System Identifier=0x8000,0-11-11-22-22-74Admin key=0x0Operational key=0x0Partner System Identifier=0x8000,0-11-11-22-22-75Operational key=0x0Max delay=0Aggregate or individual=1port-channel2Local System Identifier=0x8000,0-11-11-22-22-74Admin key=0x1Operational key=0x1Partner System Identifier=0x8000,0-11-11-22-22-75Operational key=0x1Max delay=0Aggregate or individual=1Related Commands
show lacp system-identifier
To display the Link Aggregation Control Protocol (LACP) system identifier for the device, use the show lacp system-identifier command.
show lacp system-identifier
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
The LACP system ID is the combination of the configurable LACP system priority value and the MAC address.
Each system that runs LACP has an LACP system priority value. You can accept the default value of 32768 for this parameter, or you can configure a value between 1 and 65535. LACP uses the system priority with the MAC address to form the system ID and also uses the system priority during negotiation with other devices. A higher system priority value means a lower priority.
The system ID is different for each virtual device context (VDC).
This command does not require a license.
Examples
This example shows how to display the information about the LACP port channel for a specific port channel:
switch> show lacp system-identifier8000,AC-12-34-56-78-90Related Commands
show port-channel capacity
To display the number of port channels currently used and the number of port channels that are still available on the device, use the show port-channel capacity command.
show port-channel capacity
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode.
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
There are a total of 768 port channels and virtual port channels (vPCs) available on each device.
This command does not require a license.
Examples
This example shows how to display the number of used and available port channels on the device:
switch (config) # show port-channel capacityPort-channel resources768 total 103 used 665 free 13% usedRelated Commands
show port-channel compatibility-parameters
To display the parameters that must be the same among the member ports in order to join a port channel, use the show port-channel compatibility parameters command.
show port-channel compatibility-parameters
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
When you add an interface to a channel group, the software checks certain interface attributes to ensure that the interface is compatible with the channel group. For example, you cannot add a Layer 3 interface to a Layer 2 channel group. The software also checks a number of operational attributes for an interface before allowing that interface to participate in the port-channel aggregation.
This command displays the list of compatibility checks that the system uses.
Using the channel-group command, you can force ports with incompatible parameters to join the port channel as long as the following parameters are the same:
•
•
•
•
•
•
Note
This command does not require a license.
Examples
This example shows how to display the list of compatibility checks that the system makes before an interface to a channel group:
switch# show port-channel compatibility-parameters* port modeMembers must have the same port mode configured, either E or AUTO. If theyare configured in AUTO port mode, they have to negotiate E mode when theycome up. If a member negotiates a different mode, it will be suspended.* speedMembers must have the same speed configured. If they are configured in AUTOspeed, they have to negotiate the same speed when they come up. If a membernegotiates a different speed, it will be suspended.* MTUMembers have to have the same MTU configured. This only applies to ethernetport-channel.* MEDIUMMembers have to have the same medium type configured. This only applies toethernet port-channel.* Span modeMembers must have the same span mode.* sub interfacesMembers must not have sub-interfaces.* Duplex ModeMembers must have same Duplex Mode configured.* Ethernet LayerMembers must have same Ethernet Layer (switchport/no-switchport) configured.* Span PortMembers cannot be SPAN ports.* Storm ControlMembers must have same storm-control configured.* Flow ControlMembers must have same flowctrl configured.* CapabilitiesMembers must have common capabilities.* portMembers port VLAN info.* portMembers port does not exist.* switching portMembers must be switching port, Layer 2.* port access VLANMembers must have the same port access VLAN.* port native VLANMembers must have the same port native VLAN.* port allowed VLAN listMembers must have the same port allowed VLAN list.Related Commands
channel-group
Adds or removes interfaces to port-channel groups and assigns the port-channel mode to the interface.
show port-channel database
To display information about the current running of the port channels, use the show port-channel database command.
show port-channel database [interface port-channel channel-number]
Syntax Description
channel-number
Port-channel number for the information that you want to display. The range of values is from 1 to 4096.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
If you do not specify the channel-number, all channel groups are displayed. This command displays Link Aggregation Control Protocol (LACP)-enabled ports channels and port channels without an associated aggregation protocol.
This command does not require a license.
Examples
This example shows how to display information about the current running of all port channels:
switch# show port-channel databaseport-channel5Administrative channel mode is activeOperational channel mode is activeLast membership update is successful1 ports in total, 0 ports upAge of the port-channel is 1d:16h:18m:50sTime since last bundle is 1d:16h:18m:56sLast bundled member isPorts: Ethernet2/5 [down]port-channel20Administrative channel mode is activeOperational channel mode is activeLast membership update is successful1 ports in total, 0 ports upAge of the port-channel is 1d:16h:18m:50sTime since last bundle is 1d:16h:18m:56sLast bundled member isPorts: Ethernet2/20 [down]This example shows how to display information about the current running of a specific port channel:
switch# show port-channel database interface port-channel 20port-channel20Administrative channel mode is activeOperational channel mode is activeLast membership update is successful1 ports in total, 0 ports upAge of the port-channel is 1d:16h:23m:14sTime since last bundle is 1d:16h:23m:20sLast bundled member isPorts: Ethernet2/20 [down]Related Commands
show port-channel summary
Displays a summary of information about all port channels.
show port-channel load-balance
To display information about load-balancing using port channels, use the show port-channel load-balance command.
show port-channel load-balance [forwarding-path interface port-channel channel-number]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about the current port-channel load balancing for the system:
switch# show port-channel load-balancePort Channel Load-Balancing Configuration:System: source-dest-ip-vlanPort Channel Load-Balancing Addresses Used Per-Protocol:Non-IP: source-dest-macIP: source-dest-ip-vlanRelated Commands
port-channel load-balance ethernet
Configures load balancing using port channels.
show port-channel rbh-distribution
To display information about the Result Bundle Hash (RBH) for port channels, use the show port-channel rbh-distribution command.
show port-channel rbh-distribution [interface port-channel channel-number]
Syntax Description
channel-number
Port-channel number for the information the you want to display. The range of values is from 1 to 4096.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
The RBH value ranges from 0 to 7 and is shared among port members in a port channel.
This command does not require a license.
Examples
This example shows how to display RBH distribution for a specific port channel:
switch# show port-channel rbh-distribution interface port-channel 4ChanId Member port RBH values Num of buckets-------- ------------- ----------------- ----------------4 Eth3/13 4,5,6,7 44 Eth3/14 0,1,2,3 4Related Commands
show port-channel summary
To display summary information about the port channels, use the show port-channel summary command.
show port-channel summary
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
If the Link Aggregation Control Protocol (LACP) is not enabled, the output shows NONE in the Protocol column of the display.
A channel-group interface can be in the following operational states:
•
•
–
–
•
•
•
•
•
–
–
•
•
This command does not require a license.
Examples
This example shows how to display summary information for the port channels:
switch# show port-channel summaryFlags: D - Down P - Up in port-channel (members)I - Individual H - Hot-standby (LACP only)s - Suspended r - Module-removedS - Switched R - RoutedU - Up (port-channel)-------------------------------------------------------------------Group Port- Type Protocol Member PortsChannel-------------------------------------------------------------------5 Po5(SD) Eth LACP Eth2/5(D)20 Po20(RD) Eth LACP Eth2/20(D)Related Commands
show port-channel traffic
To display traffic statistics for port channels, use the show port-channel traffic command.
show port-channel traffic [interface port-channel channel-number]
Syntax Description
channel-number
Port-channel number for the traffic statistics that you want to display. The range of values is from 1 to 4096.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
This command displays the percentage of transmitted and received unicast, multicast, and broadcast traffic about the port channel.
If you do not specify the channel-number, information for all port channels is displayed.
This command does not require a license.
Examples
This example shows how to display the traffic statistics for all port channels:
switch(config)# show port-channel trafficChanId Port Rx-Ucst Tx-Ucst Rx-Mcst Tx-Mcst Rx-Bcst Tx-Bcst------ --------- ------- ------- ------- ------- ------- -------5 Eth2/5 0.0% 0.0% 0.0% 0.0% 0.0% 0.0%------ --------- ------- ------- ------- ------- ------- -------20 Eth2/20 0.0% 0.0% 0.0% 0.0% 0.0% 0.0%This example shows how to display the traffic statistics for a specific port channel:
switch(config)# show port-channel traffic interface port-channel 5ChanId Port Rx-Ucst Tx-Ucst Rx-Mcst Tx-Mcst Rx-Bcst Tx-Bcst------ --------- ------- ------- ------- ------- ------- -------5 Eth2/5 0.0% 0.0% 0.0% 0.0% 0.0% 0.0%Related Commands
show port-channel usage
To display the port-channel numbers used and available, use the show port-channel usage command.
show port-channel usage
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
This command displays port-channel numbers used and available in the virtual device context (VDC) that you are monitoring.
The number of port-channel numbers available across all VDCs for the entire system is from 1 to 4096.
This command does not require a license.
Examples
This example shows how to display the usage for all port channels:
switch# show port-channel usageTotally 2 port-channel numbers used====================================Used : 5 , 20Unused: 1 - 4 , 6 - 19 , 21 - 4096Related Commands
show port-profile
To display information about port profiles, use the show port-profile command.
show port-profile [brief | expand-interface [name name] | name name | usage]
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
Use the show port-profile command to display information about the configured port profiles on the device. It displays all configured port profiles.
Port profiles are not aware of default values, so the default value configuration appears in the port profiles. For example, MTU 1500 is a default value and does not appear in the running-config display of an interface. However, because port profiles are unaware of default values, MTU 1500 appears in the port-profile display.
This command does not require a license.
Examples
These examples show how to display information about port profiles:
switch(config)# show port-profiletry1type: Ethernetdescription:status: enabledmax-ports: 512inherit:config attributes:channel-group 5evaluated config attributes:channel-group 5assigned interfaces:Ethernet1/1try2type: Ethernetdescription:status: disabledmax-ports: 512inherit:config attributes:evaluated config attributes:assigned interfaces:switch(config)# show port-profile brief----------------------------------------------------------Port Profile Conf Eval Assigned ChildProfile State Items Items Intfs Profs----------------------------------------------------------try1 1 1 1 1 0try2 0 0 0 0 0switch(config)# show port-profile expand-interfacetry1Ethernet1/1channel-group 5try2switch(config)# show port-profile name try1try1type: Ethernetdescription:status: enabledmax-ports: 512inherit:config attributes:channel-group 5evaluated config attributes:channel-group 5assigned interfaces:Ethernet1/1switch(config)# show port-profile usagetry1Ethernet1/1This example shows how to display port profiles and values that you have entered in interface configuration mode using the show running-config command:
switch(config)# show running-config interface ethernet 8/5interface ethernet8/5inherit try1mtu 3000Related Commands
show running-config interface
To display the running configuration for a specific interface, use the show running-config interface command.
show running-config interface [all | {ethernet {slot/port} [all]} | expand-port-profile | {loopback {number} [all]} | {mgmt0 [all]} | {port-channel {channel-number} [membership]} | {tunnel {number} [all]} | {vlan {vlan-id} [all]}
Syntax Description
Defaults
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
4.0
This command was introduced.
4.2(1)
The expand-port-profile parameter was introduced.
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display information about the running configuration for a specific Ethernet interface:
switch(config)# show running-config interface ethernet 2/7version 4.0(3)interface Ethernet2/7description Ethernet port 3 on module 1mtu 8000delay 20udld enableno shutdownThis example shows how to display information about the running configuration for a specific range of Ethernet interfaces:
switch(config)# show running-config interface ethernet 2/7 - 9version 4.0(3)interface Ethernet2/7description Ethernet port 3 on module 1mtu 8000delay 20udld enableno shutdowninterface Ethernet2/8no shutdowninterface Ethernet2/9no shutdownThis example shows how to display information about the running configuration for a specific loopback interface:
switch(config)# interface loopback 345switch(config-if)# show running-config interface loopback 345version 4.0(3)interface loopback345This example shows how to display the running configuration for a specific port channel:
switch(config)# show running-config interface port-channel 10version 4.0(1)interface port-channel10switchportswitchport mode trunkThis example shows how to display information about the running configuration for VLAN interface:
switch(config)# show running-config interface vlan 50version 4.0(3)interface Vlan50Related Commands
show running-config interface mgmt
To display the running configuration for a specific management interface, use the show running-config interface mgmt command.
show running-config interface mgmt {number}
Syntax Description
Command Default
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the show running-config interface mgmt command to display the running configuration for a management interface.
This command does not require a license.
Examples
This example shows how to display information about the running configuration for management interface 0:
switch# show running-config interface mgmt 0version 4.0(3)interface mgmt0ip address 172.28.231.193/23Related Commands
show running-config vpc
To display the running configuration information for virtual port channels (vPCs), use the show running-config vpc command.
show running-config vpc [all]
Syntax Description[
Defaults
None
Command Modes
Any command mode.
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the running configuration for a vPC:
switch (config)# show running-config vpcversion 4.1(2)feature vpcvpc domain 2role priority 1system-priority 32667peer-keepalive destination 10.10.76.52 source 10.10.76.51 udp-port 3200 vrf maengagement interval 1000 timeout 5interface port-channel10vpc 20interface port-channel101vpc 101interface port-channel200vpc peer-linkinterface port-channel201vpc 201Related Commands
show vpc brief
Displays information about vPCs. If the feature is not enabled, this command returns an error.
show startup-config interface
To display interface configuration information in the startup-configuration, use the show startup-config interface command.
show startup-config interface [ethernet slot/port | expand-port-profile | loopback number | mgmt0 | port-channel {channel-number} [membership] | tunnel number | {vlan vlan-id}
Syntax Description
Defaults
None
Command Modes
Any command mode.
Supported User Rolesnetwork-admin
vdc-admin
Command History
4.1(2)
This command was introduced.
4.2(1)
The expand-port-profile parameter was introduced.
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the information in the startup configuration for the interface Ethernet 7/1:
switch(config)# show startup-config interface ethernet 7/1version 4.1(2)interface Ethernet7/1ip pim sparse-modeRelated Commands
show startup-config vpc
To display virtual port-channel (vPC) configuration information in the startup-configuration, use the show startup-config vpc command.
show startup-config vpc [all]
Syntax Description[
Defaults
None
Command Modes
Any command mode.
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to display the vPC information in the startup configuration:
switch(config)# show startup-config vpcversion 4.1(2)feature vpcvpc domain 1interface port-channel10vpc peer-linkinterface port-channel20vpc 100Related Commands
show vpc brief
Displays information about vPCs. If the feature is not enabled, the system displays an error when you enter this command.
show udld
To display information about the UDLD configuration, use the show udld command.
show udld [ethernet slot/port | global | neighbors]
Syntax Description
Command Default
None
Command Modes
Any command mode
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the show udld command to display information about the UDLD configuration for an interface. UDLD must be enabled on the device before you can display this command; enter the feature udld command to enable UDLD globally on the device.
This command does not require a license.
Examples
This example shows how to display information about the UDLD configuration for Ethernet port 2/7:
switch# show udld ethernet 2/7Interface Ethernet2/7--------------------------------Port enable administrative configuration setting: disabledPort enable operational state: disabledCurrent bidirectional state: unknownCurrent operational state: udld-init - Multiple neighbor not detectedMessage interval: 7Timeout interval: 5Related Commands
udld
Configures the ports to use a UDLD mode.
feature udld
Enables UDLD globally on device.
show vpc brief
To display brief information about the virtual port channels (vPCs), use the show vpc brief command.
show vpc brief [vpc number]
Syntax Description
vpc number
(Optional) Displays the brief information for the specified vPC. The range is from 1 to 4096.
Defaults
None
Command Modes
Any command mode.
Supported User Rolesnetwork-admin
vdc-admin
Command History
4.1(3)
This command was introduced.
4.2(1)
Display showing the number of configured vPCs was added.
4.2(1)
Display showing track object, if configured, was added.
Usage Guidelines
The show vpc brief command displays the vPC domain ID, the peer-link status, the keepalive message status, whether the configuration consistency is successful, and whether peer-link formed or the failure to form.
This command is not available if you have not enabled the vPC feature. See feature vpc for information on enabling vPCs.
Beginning with Cisco Release 4.2(1), you can display the track object, if you have configured a tracked object for running vPCs on a single module under the vpc-domain configuration mode. See the Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 4.2 for information on this feature.
This command does not require a license.
Examples
This example shows how to display brief information about the vPCs:
switch(config)# show vpc briefLegend:(*) - local vpc is down, forwarding via vPC peer-linkvPC domain id : 10Peer status : peer adjacency formed okvPC keep-alive status : peer is aliveConfiguration consistency status: successvPC role : primaryNumber of vPC configured : 1vPC Peer-link status---------------------------------------------------------------------id Port Status Active vlans-- ---- ------ --------------------------------------------------1 Po10 up 1-100vPC status----------------------------------------------------------------------id Port Status Consistency Reason Active vlans-- ---- ------ ----------- -------------------------- ------------20 Po20 up success success 1-100This example also shows how to display brief information about the vPCs. In this example, the port channel failed the consistency check, and the device displays the reason for the failure:
switch(config)# show vpc briefLegend:(*) - local vpc is down, forwarding via vPC peer-linkvPC domain id : 10Peer status : peer adjacency formed okvPC keep-alive status : peer is aliveConfiguration consistency status: failedConfiguration consistency reason: vPC type-1 configuration incompatible - STP interface port type inconsistentvPC role : secondaryNumber of vPC configured : 1vPC Peer-link status---------------------------------------------------------------------id Port Status Active vlans-- ---- ------ --------------------------------------------------1 Po10 up 1-100vPC status----------------------------------------------------------------------id Port Status Consistency Reason Active vlans-- ---- ------ ----------- -------------------------- ------------20 Po20 up failed vPC type-1 configuration -incompatible - STPinterface port typeinconsistentThis example also shows how to display information about the tracked objects in the vPCs, which is available beginning in Cisco NX-OS Release 4.2(1):
switch(config)# show vpc briefLegend:(*) - local vpc is down, forwarding via vPC peer-linkvPC domain id : 1Peer status : peer adjacency formed okvPC keep-alive status : peer is aliveConfiguration consistency status: successvPC role : secondaryNumber of vPC configured : 3Track object : 12vPC Peer-link status---------------------------------------------------------------------id Port Status Active vlans-- ---- ------ --------------------------------------------------1 Po10 up 1-100Related Commands
feature vpc
Enables vPCs on the device.
show port channel summary
Displays information about port channels.
show vpc consistency-parameters
To display the consistency of parameters that must be compatible across the virtual port-channel (vPC) interfaces, use the show vpc consistency-parameters command.
show vpc consistency-parameters {global | interface port-channel channel-number | vpc number}}
Syntax Description
Defaults
None
Command Modes
Any command mode.
Supported User Rolesnetwork-admin
vdc-admin
Command History
4.2(1)
Display of local suspended VLANs was added.
Note
4.2(1)
vpc argument was added.
Usage Guidelines
The show vpc consistency-parameters command displays the configuration of all the vPC Type 1 parameters on both sides of the vPC peer link.
Note
The vPC Type 1 configuration parameters are as follows:
•
•
•
•
–
–
–
•
•
•
•
–
–
–
•
–
–
–
•
•
This command is not available if you have not enabled the vPC feature. See feature vpc for information on enabling vPCs.
This command does not require a license.
Examples
This example shows how to display the vPC consistency parameters for the specified port channel:
switch (config)# show vpc consistency-parameters globalLegend:Type 1 : vPC will be suspended in case of mismatchName Type Local Value Peer Value------------- ---- ------------------------ --------------------------STP Mode 1 Rapid-PVST Rapid-PVSTSTP Disabled 1 None NoneSTP MST 1 "" ""Region NameSTP MST 1 0 0RegionRevisionSTP MST 1RegionInstance toVLAN MappingSTP Loopguard 1 Disabled DisabledSTP Bridge 1 Enabled EnabledAssuranceSTP Port Type 1 Normal NormalAllowed VLAN - 1-100 1-100Local suspended - 1-50 -VLANsThis example shows how to display the vPC consistency parameters for the specified port channel:
switch (config)# show vpc consistency-parameters interface port-channel 20Legend:Type 1 : vPC will be suspended in case of mismatchName Type Local Value Peer Value------------- ---- ------------------------ --------------------------STP Port Type 1 Default DefaultSTP Port 1 None NoneGuardmode 1 on onSpeed 1 10 Gb/s 10 Gb/sDuplex 1 full fullPort Mode 1 trunk trunkNative Vlan 1 1 1MTU 1 1500 1500Allowed VLAN - 1-100 1-100bitsetRelated Commands
show vpc orphan-ports
To display ports that are not part of the virtual port channel (vPC) but have common VLANs, use the show vpc orphan-ports command.
show vpc orphan-ports
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode.
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
The show vpc orphan-ports command displays those ports that are not part of the vPC but that share common VLANs with ports that are part of the vPC.
This command is not available if you have not enabled the vPC feature. See feature vpc for information on enabling vPCs.
This command does not require a license.
Examples
This example shows how to display vPC orphan ports:
switch(config)# show vpc orphan portsNote:--------::Going through port database. Please be patient.::--------VLAN Orphan Ports------- -------------------------1 Po6002 Po6003 Po6004 Po6005 Po6006 Po6007 Po6008 Po6009 Po60010 Po60011 Po60012 Po60013 Po60014 Po60015 Po600Related Commands
feature vpc
Enables vPCs on the device.
show vpc brief
Displays brief information about vPCs.
show vpc peer-keepalive
To display the destination IP for the virtual port-channel (vPC) peer keepalive message and the status of the messages, use the show vpc peer-keepalive command.
show vpc peer-keepalive
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode.
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
The show vpc peer-keepalive command displays the destination IP of the peer keepalive message for the vPC. The command also displays the send and receive status as well as the last update from the peer in seconds and milliseconds
Note
This command is not available if you have not enabled the vPC feature. See feature vpc for information on enabling vPCs.
This command does not require a license.
Examples
This example shows how to display information about the peer-keepalive message:
n7k-2(config-vpc-domain)# show vpc peer-keepalivevPC keep-alive status : peer is alive--Send status : Success--Last send at : 2008.05.17 18:23:53 986 ms--Sent on interface : Eth7/16--Receive status : Success--Last receive at : 2008.05.17 18:23:54 99 ms--Received on interface : Eth7/16--Last update from peer : (0) seconds, (486) msecvPC Keep-alive parameters--Destination : 172.23.145.213--Keepalive interval : 1000 msec--Keepalive timeout : 5 seconds--Keepalive hold timeout : 3 seconds--Keepalive vrf : pkal--Keepalive udp port : 3200--Keepalive tos : 192Related Commands
show vpc brief
Displays information about vPCs. If the feature is not enabled, the system displays an error when you enter this command.
show vpc role
To display information about the virtual port-channel (vPC) role of the peer device, use the show vpc role command.
show vpc role
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any command mode.
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
The show vpc role command displays the following information about the vPC status:
•
•
•
•
•
•
This command is not available if you have not enabled the vPC feature. See feature vpc for information on enabling vPCs.
This command does not require a license.
Examples
This example shows how to display the vPC role information of the device that you are working on:
switch (config)# show vpc rolePrimary:vPC Role status----------------------------------------------------vPC role : primaryDual Active Detection Status : 0vPC system-mac : 00:23:04:ee:be:01vPC system-priority : 32667vPC local system-mac : 00:22:55:79:ea:c1vPC local role-priority : 32667Secondary:vPC Role status----------------------------------------------------vPC role : secondaryDual Active Detection Status : 0vPC system-mac : 00:23:04:ee:be:01vPC system-priority : 32667vPC local system-mac : 00:22:55:79:de:41vPC local role-priority : 32667When you reload the primary vPC peer device, the secondary vPC peer device assumes the role of primary device. The following example shows how the vPC role displays then on the new primary device:
switch (config)# show vpc rolevPC Role status----------------------------------------------------vPC role : secondary, operational primaryDual Active Detection Status : 0vPC system-mac : 00:23:04:ee:be:64vPC system-priority : 32667vPC local system-mac : 00:22:55:79:de:41vPC local role-priority : 32667Related Commands
show vpc statistics
To display virtual port-channel (vPC) statistics, use the show vpc statistics command.
show vpc statistics {peer-keepalive | peer-link | vpc number}
Syntax Description[
Defaults
None
Command Modes
Any command mode.
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
The peer-link parameter displays the same information as the show interface port-channel channel number command for the vPC peer-link port channel.
The vpc number parameter displays the same information as the show interface port-channel channel number command for the specified vPC port channel.
This command is not available if you have not enabled the vPC feature. See feature vpc for information on enabling vPCs.
This command does not require a license.
Examples
This example shows how to display statistics about the peer-keepalive message:
switch# show vpc statistics peer-keepalivevPC keep-alive status : peer is aliveVPC keep-alive statistics----------------------------------------------------peer-keepalive tx count: 1036peer-keepalive rx count: 1028average interval for peer rx: 995Count of peer state changes: 1Related Commands
shutdown
To bring the port administratively down, use the shutdown command.
To bring the port administratively up, use the no shutdown command.
shutdown [force]
no shutdown [force]
Syntax Description
Command Default
None
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the shutdown command to bring the port administratively down. Use the no shutdown command to bring the port administratively up.
This command does not require a license.
Examples
This example shows how to bring the port administratively down:
switch(config-if)# shutdownThis example shows how to bring the port administratively up:
switch(config-if)# no shutdown
Related Commands
speed
To set the speed for Ethernet ports or management interfaces or set the port to autonegotiate its speed with other ports on the link, use the speed command.
speed {10 | 100 | 1000 | 10000 | auto [10 [100 [1000]]]}
Syntax Description
10
Sets the speed at 10 Mbps.
100
Sets the speed at 100 Mbps.
1000
Sets the speed at 1 Gbps.
10000
Sets the speed at 10 Gbps.
auto
Sets the interface to autonegotiation.
Command Default
None
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Before you begin, make sure that the remote port has a speed setting that supports your changes for the local port. If you want to set the local port to use a specific speed, you must set the remote port for the same speed or set the local port to autonegotiate the speed.
The interface speed and duplex mode are interrelated, so you should configure both of their parameters at the same time.
The interface speed that you specify can affect the duplex mode used for an interface, so you should set the speed before setting the duplex mode. If you set the speed for autonegotiation, the duplex mode is automatically set to be autonegotiated. If you specify 10- or 100-Mbps speed, the port is automatically configured to use half-duplex mode, but you can specify full-duplex mode instead. If you specify a speed of 1000 Mbps (1 Gbps) or faster, full duplex is automatically used. For more details about configuring this command, see the Cisco NX-OS Interfaces Configuration Guide.
This command does not require a license.
Examples
This example shows how to set the speed of Ethernet port 1 on the 48-port 10/100/1000 module in slot 3 to 1000 Mbps and full-duplex mode:
switch# config tswitch(config)# interface ethernet 3/1switch(config-if)# speed 1000switch(config-if)# duplex fullRelated Commands
duplex
Specifies the duplex mode as full, half, or autonegotiate.
show interface
Displays the interface status, which includes the speed parameters.
state enabled
To enable the specified port profile, use the state enabled command. To return to the default value, use the no form of this command.
state enabled
no state enabled
Syntax Description
This command has no keywords or arguments.
Defaults
Disabled
Command Modes
Port-profile configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
Use the state enabled command to enable the specified port profile. See the port-profile command for information about the port-profile feature.
To apply the port-profile configurations to the interfaces, you must enable the specific port profile. You can configure and inherit a port profile onto a range of interfaces prior to enabling the port profile; you would then enable that port profile for the configurations to take effect on the specified interfaces. The maximum number of interfaces that can inherit a single profile is 512.
If you inherit one or more port profiles onto an original port profile, only the last inherited port profile must be enabled; the system assumes that the underlying port profiles are enabled.
This command does not require a license.
Examples
This example shows how to enable the port-profile feature:
switch(config)# port-profile type ethernet testswitch(config-ppm)# state enabledRelated Commands
switchport
To set the interface as a Layer 2 switching port, use the switchport command. To return the interface to the default Layer 3 routed interface status and cause all Layer 2 configuration to be erased, use the no form of this command.
switchport
no switchport
Syntax Description
This command has no keywords or arguments.
Defaults
Interfaces are Layer 3 by default.
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
You must enter the switchport command without any keywords to configure the LAN interface as a Layer 2 interface before you can enter additional switchport commands with keywords. This action is required only if you have not entered the switchport command for the interface.
The default switchport mode is the access mode. Use the switchport mode command to do the following:
•
•
•
Enter the no switchport command to shut down the port and then reenable it. This action may generate messages on the device to which the port is connected.
When you use the no switchport command, all the Layer 2 configuration is deleted from that interface, and the interface will have the default VLAN configuration.
The port will go down and reinitialize when you change the interface mode.
This command does not require a license.
Examples
This example shows how to cause a port interface to stop operating as a Cisco routed port and convert to a Layer 2 switched interface:
switch(config-if)# switchportRelated Commands
show interface switchport
Displays the administrative and operational status of a switching (nonrouting) port.
switchport access vlan
To set the access VLAN when the interface is in access mode, use the switchport access vlan command. To reset the access-mode VLAN to the appropriate default VLAN for the device, use the no form of this command.
switchport access vlan vlan-id
no switchport access vlan
Syntax Description
vlan-id
VLAN to set when the interface is in access mode; valid values are from 1 to 4094, except for the VLANs reserved for internal switch use.
Defaults
VLAN1
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
You must enter the switchport command without any keywords to configure the LAN interface as a Layer 2 interface before you can enter the switchport access vlan command. This action is required only if you have not entered the switchport command for the interface.
Enter the no switchport access vlan command to shut down the port and then reenable it. This action may generate messages on the device to which the port is connected.
Use the no form of the switchport access vlan command to reset the access-mode VLAN to the appropriate default VLAN for the device.
This command does not require a license.
Examples
This example shows how to cause a port interface that has already been configured as a switched interface to operate as an access port in VLAN 2 instead of the platform's default VLAN in the interface-configuration mode:
switch(config-if)# switchport access vlan 2Related Commands
show interface switchport
Displays the administrative and operational status of a switching (nonrouting) port.
switchport host
To configure a port that is not connected to any other devices as a Layer 2 access port with optimized packet forwarding, use the switchport host command. To disable a port that is not connected to any other devices as a Layer 2 access, use the no form of this command.
switchport host
no switchport host
Syntax Description
This command has no keywords or arguments.
Defaults
Interfaces are Layer 3 by default.
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
You must enter the switchport command without any keywords to configure the LAN interface as a Layer 2 interface before you can enter the switchport host command. This action is required only if you have not entered the switchport command for the interface.
Entering the switchport host command on an interface:
•
•
•
You should enter the switchport host command only on ports that are connected to a single host. When you use this command with an interface connected to other than a single host, the device returns an error message.
To optimize the port configuration, entering the switchport host command sets the switch port mode to access and disables channel grouping. Only an end station can accept this configuration.
This command toggles the port if it is in the UP state.
This command does not require a license.
Examples
This example shows how to optimize an access port configuration for a host connection:
switch(config-if)# switchport hostRelated Commands
show interface switchport
Displays the administrative and operational status of a switching (nonrouting) port.
switchport mode
To set the Layer 2 interface type, use the switchport mode command. To return the interface to the Layer 2 access mode, use the no form of this command.
switchport mode {access | trunk}
no switchport mode
Syntax Description
Defaults
access ports
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
You must enter the switchport command without any keywords to configure the LAN interface as a Layer 2 interface before you can enter the switchport mode command. This action is required only if you have not entered the switchport command for the interface.
If you enter access mode, the interface goes into nontrunking mode; if you enter trunk mode, the interface goes into trunking mode.
To correctly deliver the traffic on a trunk port with several VLANs, the switch uses the IEEE 802.1Q encapsulation, or tagging, method. If an access port receives a packet with an 802.1Q tag in the header, that port drops the packet without learning its MAC source address.
Note
The port will go down and reinitialize when you change the interface mode.
This command does not require a license.
Examples
This example shows how to set the interface to trunking mode:
switch(config-if)# switchport mode trunkRelated Commands
show interface switchport
Displays the administrative and operational status of a switching (nonrouting) port.
switchport trunk allowed vlan
To set the list of allowed VLANs on the trunking interface, use the switchport trunk allowed vlan command. To allow all VLANs on the trunking interface, use the no form of this command.
switchport trunk allowed vlan {vlan-list | add vlan-list | all | except vlan-list | none | remove vlan-list}
no switchport trunk allowed vlan
Syntax Description
Defaults
All VLANs
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
You must enter the switchport command without any keywords to configure the LAN interface as a Layer 2 interface before you can enter the switchport trunk allowed vlan command. This action is required only if you have not entered the switchport command for the interface.
You can enter the switchport trunk allowed vlan command on interfaces where the Switched Port Analyzer (SPAN) destination port is either a trunk or an access port.
If you remove VLAN 1 from a trunk, the trunk interface continues to send and receive management traffic in VLAN 1.
This command does not require a license.
Examples
This example shows how to add a series of consecutive VLANs to the list of allowed VLANs on a trunking port:
switch(config-if)# switchport trunk allowed vlan add 40-50Related Commands
show interface switchport
Displays the administrative and operational status of a switching (nonrouting) port.
switchport trunk native vlan
To change the native VLAN ID when the interface is in trunking mode, use the switchport trunk native vlan command. To return the native VLAN ID to VLAN 1, use the no form of this command.
switchport trunk native vlan vlan-id
no switchport trunk native vlan
Syntax Description
vlan-id
Native VLAN for the trunk in 802.1Q trunking mode. The range of valid values is from 1 to 4094, except the internally reserved VLANs 3968 to 4047 and 4094.
Defaults
VLAN1
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
You must enter the switchport command without any keywords to configure the LAN interface as a Layer 2 interface before you can enter the switchport trunk native vlan command. This action is required only if you have not entered the switchport command for the interface.
Note
Use the no form of the native vlan command to reset the native mode VLAN to the default VLAN1 for the device.
This command does not require a license.
Examples
This example shows how to configure the native VLAN for an interface in trunk mode:
switch(config-if)# switchport trunk native vlan 5Related Commands
show interface switchport
Displays the administrative and operational status of a switching (nonrouting) port.
system default switchport
To change the default interface mode for the system from Layer 3 routing to Layer 2 switching. use the system default switchport command. To return the system to Layer 3 routing default interface mode, use the no form of this command.
system default switchport [shutdown]
no system default switchport [shutdown]
Syntax Description
Defaults
None
Command Modes
Global configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
The system default switchport command makes all the interfaces Layer 2 access ports.
This command does not require a license.
Examples
This example shows how to configure the system so that all the interfaces are in Layer 2 access mode:
switch(config-if)# system default switchportRelated Commands
show interface switchport
Displays the administrative and operational status of a switching (nonrouting) port.
system jumbomtu
To configure the system jumbo MTU size for Layer 2 interfaces, use the system jumbomtu command.
system jumbomtu size
Syntax Description
Command Default
The system jumbo MTU default size is 1500 bytes.
Command Modes
Global configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Use the system jumbomtu command to specify the MTU size for Layer 2 interfaces. The range of configurable values are 1500 to 9216 bytes.
The physical level uses an unchangeable bandwidth of 1 GB.
This command does not require a license.
Examples
This example shows how to configure the system jumbo MTU as 8000 bytes and how to change the MTU specification for an interface that was configured with the previous jumbo MTU size:
switch# config tswitch(config)# system jumbomtu 8000switch(config)# show running-configswitch(config)# interface ethernet 2/2switch(config-if)# switchportswitch(config-if)# mtu 4608Related Commands
show running-config
Displays the current operating configuration, which includes the system jumbo MTU size.
system-mac
To overwrite the MAC address that the device creates for the virtual port-channel (vPC) domain when you create a vPC domain, use the system-mac command. To return to the default vPC system MAC address, use the no form of this command.
system-mac mac-address
no system-mac
Syntax Description[
Defaults
None
Command Modes
vpc-domain command mode.
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
You must enable the vPC feature before you can create a vPC system MAC address.
Use the system-mac command to overwrite the MAC address created by the system once you create a vPC domain. By default, the system creates a MAC address for the vPC when you create a vPC domain based on the domain ID. Cisco reserved a range of MAC addresses from the IEEE for this purpose and these addresses will be used to complete the last 10 bits of the vPC domain MAC address. The range of default MAC addresses is as follows:
•
•
•
This command does not require a license.
Examples
This example shows how to create a vPC system MAC address:
switch# config tswitch(config)# vpc domain 5switch(config-vpc-domain)# system-mac 22cd.34ab.ca32Related Commands
system-priority
To overwrite the system priority that the device creates for the virtual port-channel (vPC) domain when you create a vPC domain, use the system-priority command. To return to the default vPC system priority, use the no form of this command.
system-priority priority
no system-priority priority
Syntax Description[
Defaults
32667
Command Modes
vpc-domain command mode.
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
You must enable the vPC feature before you can create a vPC system priority.
Note
This command does not require a license.
Examples
This example shows how to create a vPC system priority:
switch# config tswitch(config)# vpc domain 5switch(config-vpc-domain)# system-priority 4000Related Commands
track
To configure the system to monitor the track-list object that contains all the virtual port-channel (vPC) links to the core and to the vPC peer link when you are using only a single module for all links, use the track command. To return to the default, use the no form of this command.
track track-object-id
no track track-object-id
Syntax Description
Defaults
No tracking
Command Modes
vpc configuration mode
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
Beginning with Release 4.2, if you must configure all the vPC peer links and core-facing interfaces on a single N7K-M132XP-12 module, you should configure a track object and a track list that is associated with the Layer 3 link to the core and on all vPC peer links on both vPC peer devices. You can use this configuration to avoid dropping traffic if that particular module goes down because when all the tracked objects on the track list go down, the system does the following:
•
•
Once you configure this feature and if the module fails, the system automatically suspends all the vPC links on the primary vPC peer device and stops the peer-keepalive messages. This action forces the vPC secondary device to take over the primary role and all the vPC traffic to go to this new vPC primary device until the system stabilizes.
Create a track list that contains all the links to the core and all the vPC peer links as its object. Enable tracking for the specified vPC domain for this track list. Apply this same configuration to the other PC peer device. See the Cisco Nexus 7000 Series NX-OS Unicast Routing Configuration Guide, Release 4.2, for information about configuring object tracking and track lists.
This command does not require a license.
Examples
This example shows how to put the previously configured track-list object into the vPC domain on the vPC peer device:
switch# config tswitch(config)# vpc domain 5switch(config-vpc-domain)# track object 5Related Commands
show vpc brief
Displays information on a vPC tracked object.
feature vpc
Enables vPCs on the device.
tunnel destination
To configure the destination endpoint for a tunnel, use the tunnel destination command in interface configuration mode. To remove the tunnel destination, use the no form of this command.
tunnel destination {ip-address | host-name}
no tunnel destination {ip-address | host-name}
Syntax Description
Defaults
None
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
Use the tunnel destination command to configure the destination address for an IP tunnel.
You should not have two tunnels using the same encapsulation mode with the same source and destination address.
This command requires the Enterprise license.
Examples
This example shows how to configure the tunnel destination:
switch(config-if)# tunnel destination 192.0.2.120Related Commands
tunnel mode
To configure the tunnel encapsulation mode for a tunnel, use the tunnel mode command in interface configuration mode. To restore the default value, use the no form of this command.
tunnel mode gre {ip | ipv6}
no tunnel mode gre {ip | ipv6}
Syntax Description
ip
Configures this tunnel encapsulation mode as IPv4.
ip v6
Configures this tunnel encapsulation mode as IPv6.
Defaults
None
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
Use the tunnel mode command to configure the tunnel encapsulation mode for a tunnel.
This command requires the Enterprise license.
Examples
This example shows how to configure the tunnel mode:
switch(config-if)# tunnel mode gre ipRelated Commands
tunnel path-mtu-discovery
To enable Path MTU Discovery (PMTUD) on a tunnel interface, use the tunnel path-mtu-discovery command in interface configuration mode. To disable PMTUD on a tunnel interface, use the no form of this command.
tunnel path-mtu-discovery [age-timer {aging-mins | infinite} | min-mtu mtu-bytes]
no tunnel path-mtu-discovery [age-timer {aging-mins | infinite} | min-mtu mtu-bytes]
Syntax Description
Defaults
Disabled
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
When PMTUD (RFC 1191) is enabled on a tunnel interface, the router performs PMTUD processing for the tunnel IP packets. The router always performs PMTUD processing on the original data IP packets that enter the tunnel. When PMTUD is enabled, no packet fragmentation occurs on the encapsulated packets that travel through the tunnel. Without packet fragmentation, there is a better throughput of TCP connections. PMTUD maximizes the use of available bandwidth in the network between the endpoints of a tunnel interface.
After PMTUD is enabled, the Don't Fragment (DF) bit of the IP packet header that is forwarded into the tunnel is copied to the IP header of the external IP packets. The external IP packet is the encapsulating IP packet. Adding the DF bit allows the PMTUD mechanism to work on the tunnel path of the tunnel. The tunnel endpoint listens for Internet Control Message Protocol (ICMP) unreachable too-big messages and modifies the IP MTU of the tunnel interface, if required.
When the aging timer is configured, the tunnel code resets the tunnel MTU after the aging timer expires. After the tunnel MTU is reset, a set of full-size packets with the DF bit set is required to trigger the tunnel PMTUD and lower the tunnel MTU. At least two packets are dropped each time that the tunnel MTU changes.
When PMTUD is disabled, the DF bit of an external (encapsulated) IP packet is set to zero even if the encapsulated packet has a DF bit set to one.
The min-mtu keyword sets a low limit through the MTU that can be learned through the PMTUD process. Any ICMP signal received that specifies an MTU less than the minimum MTU configured will be ignored. You can use this feature to prevent a denial- of-service attack from any node that can send an ICMP message to the router that specifies a very small MTU.
Note
This command requires the Enterprise license.
Examples
This example shows how to configure PMTUD:
switch(config-if)# tunnel path-mtu-discoveryRelated Commands
tunnel source
To configure the source endpoint for a tunnel, use the tunnel source command in interface configuration mode. To remove the tunnel source, use the no form of this command.
tunnel source {ip-address | interface-type number}
no tunnel source [ip-address | interface-type number]
Syntax Description
Defaults
None
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
Use the tunnel source command to configure the source address for an IP tunnel.
You should not have two tunnels using the same encapsulation mode with the same source and destination address.
This command requires the Enterprise license.
Examples
This example shows how to set the tunnel source:
switch(config-if)# tunnel source 192.0.2.120Related Commands
tunnel use-vrf
To specify which VRF to use to look up a tunnel destination IP address, use the tunnel use-vrf command in interface configuration mode. To return to the default, use the no form of this command.
tunnel use-vrf vrf-name
no tunnel use-vrf vrf-name
Syntax Description
Defaults
Default VRF
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
You should have the tunnel interface and tunnel destination IP address in the same VRF. In other words, you should have the same value for the vrf-name parameter in both the vrf member and tunnel use-vrf commands.
This command requires the Enterprise license.
Examples
This example shows how to specify the VRF in which to look up the tunnel destination IP address:
switch(config-if)# tunnel use-vrf blueRelated Commands
show interface tunnel
Displays information about the traffic about the specified tunnel interface.
show vrf interface tunnel
Displays information about the VRF tunnel interface.
tunnel ttl
To configure the time-to-live value for a tunnel, use the tunnel ttl command in interface configuration mode. To restore the default value, use the no form of this command.
tunnel ttl value
no tunnel ttl [value]
Syntax Description
Defaults
None
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
Use the tunnel ttl command to configure the time-to-live value for an IP tunnel.
This command requires the Enterprise license.
Examples
This example shows how to configure the time-to-live value for a tunnel interface:
switch(config-if)# tunnel ttl 30Related Commands
udld
To configure the interfaces to use a UDLD mode, use the udld command.
udld {enable | disable}
Syntax Description
disable
Disables the UDLD mode for fiber interfaces.
enable
Enables the normal UDLD mode for non-fiber interfaces.
Command Default
By default, UDLD is disabled for the 48-port, 10/100/1000 Ethernet module ports.
By default, UDLD is enabled for the 32-port, 10 gigabit Ethernet module ports.
Command Modes
Interface configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Before you can enable a UDLD mode for specified interfaces, you must make sure that UDLD is already enabled globally on the device. Use the feature udld command to enable UDLD globally.
Use the udld command to enable or disable UDLD separately on specified interfaces. This enables UDLD in normal mode. Enter the udld aggressive command to enable the aggressive mode on UDLD-enabled interfaces.
This command does not require a license.
Examples
This example shows how to enable the normal UDLD mode for Ethernet port 3/1:
switch# config tswitch(config)# feature udldswitch(config)# interface ethernet 3/1switch(config-if)# udld enableThis example shows how to disable UDLD for Ethernet port 3/1:
switch# config tswitch(config)# interface ethernet 3/1switch(config-if-range)# udld disableRelated Commands
feature udld
Enables UDLD globally on the device.
show udld
Displays information about the UDLD configuration.
udld aggressive
To configure the interfaces for aggressive UDLD mode, use the udld aggressive command.
udld aggressive
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Interface configuration
Global configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Before you can enable the aggressive UDLD mode for an interface, you must make sure that UDLD is already enabled globally on the device and on the specified interfaces.
Use the udld aggressive command to configure the ports to use a UDLD mode:
•
•
To use the aggressive UDLD mode, you must configure the interfaces on both ends of the link for the aggressive UDLD mode.
This command does not require a license.
Examples
This example shows how to enable fiber interfaces for the aggressive UDLD mode:
switch# config tswitch(config)# udld aggressiveThis example shows how to enable the aggressive UDLD mode for the copper Ethernet interface 3/1:
switch# config tswitch(config)# interface ethernet 3/1switch(config-if)# udld aggressiveRelated Commands
feature udld
Enables UDLD globally for the device.
show udld
Displays information about the UDLD configuration.
udld message-time
To set the UDLD message interval timer, use the udld message-time command.
udld message-time seconds
Syntax Description
seconds
Enter the number of seconds you want between sending UDLD messages. The range is from 7 to 90 seconds.
Defaults
15 seconds
Command Modes
Global configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
Before you can set the UDLD message timer, you must make sure that UDLD is already enabled globally on the device. Use the feature udld command to globally enable UDLD.
This command does not require a license.
Examples
This example shows how to configure UDLD interval to 30 seconds:
switch# config tswitch(config)# udld message-time 30Related Commands
feature udld
Enables UDLD globally for the device.
show udld
Displays information about the UDLD configuration.
udld reset
To reset the interfaces that UDLD has shut down and return them to the UP condition, use the udld reset command.
udld reset
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Global configuration
Supported User Rolesnetwork-admin
vdc-adminCommand History
Usage Guidelines
This command does not require a license.
Examples
This example shows how to reset those interfaces that UDLD has shut down:
switch# config tswitch(config)# udld resetRelated Commands
feature udld
Enables UDLD globally for the device.
show udld
Displays information about the UDLD configuration.
vlan dot1q tag native
To enable dot1q (IEEE 802.1Q) tagging for the native VLAN in a trunk, use the vlan dot1q tag native command. To return to the default where no packets are tagged in the native VLAN in a trunk, use the no form of this command.
vlan dot1q tag native
no vlan dot1q tag native
Syntax Description
This command has no arguments or keywords.
Defaults
Disabled
Command Modes
Global configuration
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
Typically, you configure 802.1Q trunks with a native VLAN ID, which strips tagging from all packets on that VLAN and allows all untagged traffic and control traffic to transit the switch. Packets that enter the switch with 802.1Q tags that match the native VLAN ID value are similarly stripped of tagging. If you choose to maintain the tagging on the native VLAN and drop untagged traffic, enter the vlan dot1q tag native command.
Use the vlan dot1q tag native command to configure the switch to tag the traffic received on the native VLAN and to admit only 802.1Q-tagged frame, dropping any untagged traffic, including untagged traffic in the native VLAN. Control traffic continues to be accepted untagged on the native VLAN on a trunked port, even when the vlan dot1q tag native command is enabled.
Use this command to enable the tagging behavior on all native VLANs on all trunked ports on the switch.
Note
This command does not require a license.
Examples
This example shows how to enable dot1q tagging for all VLANs on all trunk ports on the switch:
switch(config)# vlan dot1q tag nativeRelated Commands
vpc
To move other port channels into the virtual port channel (vPC), use the vpc command. To remove a port channel from the vPC, use the no form of this command.
vpc number
no vpc number
Syntax Description
Defaults
None
Command Modes
Interface command mode.
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
You must enable the vPC feature before you can create a vPC.
Once you have created the vPC domain ID and the vPC peer link, you create port channels to attach the downstream device to each vPC peer device. That is, you create one port channel from the downstream device to the primary vPC peer device and you create another port channel from the downstream device to the secondary peer device. Finally, working on each vPC peer device, you assign a vPC number to the port channel that connects to the downstream device. You will experience minimal traffic disruption when you are creating vPCs.
Note
This command does not require a license.
Examples
This example shows how to move a port channel into the vPC:
switch# config tswitch (config)# interface port-channel 10switch (config-if)# vpc 100Related Commands
show vpc brief
Displays information about vPCs. If the feature is not enabled, the system displays an error when you enter this command.
vpc domain
To create a virtual port-channel (vPC) domain, use the vpc domain command. To remove a vPC domain, use the no form of this command.
vpc domain domain-id
no vpc domain domain-id
Syntax Description
domain-id
Domain ID for the vPC. The range of numbers is from 1 to 1000. You must use unique vPC IDs for each vPC within a single VDC.
Defaults
None
Command Modes
Any command mode.
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
You must enable the vPC feature before you can create a vPC domain.
You put all vPC interfaces, including the vPC peer link, on both of the vPC peer devices into the identical vPC domain. You must have unique vPC domain numbers within each VDC. In Cisco NX-OS Release 4.1(3), you can have only one vPC per VDC. Once you create a vPC domain, the system automatically creates a vPC system MAC that is unique to that vPC.
You also use this command to enter the vpc-domain command mode in order to configure vPC parameters.
This command does not require a license.
Examples
This example shows how to create a vPC domain:
switch# config tswitch(config)# vpc domain 5switch(config-vpc-domain)#This example shows how to enter the vpc-domain command mode to configure an existing vPC domain:
switch# config tswitch(config)# vpc domain 5switch(config-vpc-domain)#Related Commands
show vpc brief
Displays information about vPCs. If the feature is not enabled, the system displays an error when you enter this command.
vpc peer-link
To create a virtual port-channel (vPC) peer link, use the vpc peer-link command. To remove a vPC peer link, use the no form of this command.
vpc peer-link
no vpc peer-link
Syntax Description
This command has no arguments or keywords
Command Modes
Interface command mode.
Supported User Rolesnetwork-admin
vdc-admin
Command History
Usage Guidelines
You must enable the vPC feature before you can create a vPC peer link.
You configure a port channel using 10-Gigabit Ethernet ports on the N7K-M132XP-12 module. We recommend that you use the 10-Gigabit Ethernet ports for the channel in dedicated mode and configure at least two of these ports on two different modules into the port channel for redundancy.
Use the vpc peer-link command to make that port channel a vPC peer link. The system returns an error message if you attempt to configure a 1-Gigabit Ethernet interface as a vPC peer link.
After you configure the vPC peer device and the vPC peer link is established, the system creates a new MAC address for the vPC and decides which vPC device is the primary device and which is the secondary.
This command does not require a license.
Examples
This example shows how to create a vPC peer link:
switch# config tswitch(config)# interface port-channel 20switch(config-if)# vpc peer-linkswitch(config-vpc-domain)#Related Commands
show vpc brief
Displays information about vPCs. If the feature is not enabled, the system displays an error when you enter this command.
