 Feedback
|
Table Of Contents
Cisco MDS 9000 Family Release Notes
for Cisco MDS SAN-OS Release 3.3(5a)Determining the Software Version
Determining Software Version Compatibility
Selecting the Correct Software Image for an MDS 9100 Series Switch
Selecting the Correct Software Image for an MDS 9200 Series Switch
Selecting the Correct Software Image for an MDS 9500 Series Switch
Migrating from Supervisor-1 Modules to Supervisor-2 Modules
Configuring Generation 2 Switching Modules
Upgrading Your Cisco MDS SAN-OS Software Image
Upgrading Your Version of Cisco Fabric Manager
Upgrading from Release 3.1(2c) with the PostgreSQL Patch
The Fabric Manager Installation Process Overview
FICON Supported Releases and Upgrade Paths
Reconfiguring SSM Ports Before Upgrading to SAN-OS Release 3.3(5a)
Upgrading the SSI Image on Your SSM
Upgrading a Switch with Insufficient Space for Two Images on the Bootflash
Upgrading a Cisco MDS 9124 Switch
Performing a Disruptive Upgrade on a Single Supervisor MDS Family Switch
Downgrading Your Cisco MDS SAN-OS Software Image
General Downgrading Guidelines
Downgrading the SSI Image on Your SSM
Downgrading an MDS 9222i Switch
New Features in Cisco MDS SAN-OS Release 3.3(5a)
Upgrading to Recover Loss of Performance Manager Data
Maximum Number of Zones Supported in Interop Mode 4
Upgrading the SAN-OS Software on the MDS 9222i Switch
Cisco Storage Media Encryption
Cisco SME Configuration Limits
Cisco MDS 9222i Module Upgrade
Deleting SANTap Configurations Is Required Before Downgrade
Applying Zone Configurations to VSAN 1
Running Storage Applications on the MSM-18/4
Compatibility of Fabric Manager and Data Mobility Manager
A Supervisor-2 Module Might Reset in Switches Running SAN-OS Release 3.2(x)
Limited ISSU Support on the MDS 9222i Switch
PPRC Not Supported with FCIP Write Acceleration
Using IVR In a Fabric With Mixed Code Versions
HTTP Transport Method Not Supported in Call Home
Regulatory Compliance and Safety Information
Intelligent Storage Networking Services
Installation and Configuration Note
Obtaining Documentation and Submitting a Service Request
Cisco MDS 9000 Family Release Notes
for Cisco MDS SAN-OS Release 3.3(5a)
Release Date: September 23, 2010
Part Number: OL-14116-15 B0
This document describes the caveats and limitations for switches in the Cisco MDS 9000 Family. Use this document in conjunction with documents listed in the "Related Documentation" section.
Note
Release notes are sometimes updated with new information on restrictions and caveats. Refer to the following website for the most recent version of the Cisco MDS 9000 Family Release Notes: http://www.cisco.com/en/US/products/ps5989/prod_release_notes_list.html
Table 1 shows the on-line change history for this document.
Table 1 Online History Change
A0
09/23/2010
Created release notes.
B0
11/29/2011
Updated the "Nondisruptive Upgrade Path to Cisco MDS SAN-OS Release 3.3(5a)" table.
Updated "Nondisruptive Downgrade Path from Cisco MDS SAN-OS Release 3.3(5a)" table.
Added the "HTTP Transport Method Not Supported in Call Home" limitation.
Contents
This document includes the following sections:
•
•
•
•
Introduction
The Cisco MDS 9000 Family of Multilayer Directors and Fabric Switches provides industry-leading availability, scalability, security, and management, allowing you to deploy high performance storage-area networks with lowest total cost of ownership. Layering a rich set of intelligent features onto a high performance, protocol agnostic switch fabric, the Cisco MDS 9000 Family addresses the stringent requirements of large data center storage environments: uncompromising high availability, security, scalability, ease of management, and seamless integration of new technologies.
The Cisco MDS 9000 Family SAN-OS is the underlying system software that powers the Cisco MDS 9500 Series, 9200 Series, and 9100 Series multilayer switches. The Cisco SAN-OS provides intelligent networking features, such as multiprotocol and multitransport integration, virtual SANs (VSANs), advanced security, sophisticated debug analysis tools, and unified SAN management.
Components Supported
Table 2 lists the SAN-OS software part number and hardware components supported by the Cisco MDS 9000 Family.
Note
Table 2 Cisco MDS 9000 Family Supported Software and Hardware Components
Software
M95S2K9-3.3.5a
MDS 9500 Supervisor/Fabric-2, SAN-OS software.
MDS 9500 Series only
M95S1K9-3.3.5a
MDS 9500 Supervisor/Fabric-I, SAN-OS software.
MDS 9500 Series only
M92S2K9-3.3.5a
MDS 9222 Supervisor/Fabric-2, SAN-OS software.
MDS 9200 Series only
M92S1K9-3.3.5a
MDS 9216 Supervisor/Fabric-I, SAN-OS software.
MDS 9200 Series only
M91S2K9-3.3.5a
MDS 9100 Supervisor/Fabric-2, SAN-OS software.
MDS 9100 Series only
M91S1K9-3.3.5a
MDS 9100 Supervisor/Fabric-I, SAN-OS software.
MDS 9100 Series only
License
M9500ENT1K9
Enterprise package.
MDS 9500 Series
M9200ENT1K9
Enterprise package.
MDS 9200 Series
M9100ENT1K9
Enterprise package.
MDS 9100 Series
M9500FIC1K9
Mainframe package.
MDS 9500 Series
M9200FIC1K9
Mainframe package.
MDS 9200 Series
M9100FIC1K9
Mainframe package.
MDS 9100 Series
M9100FIC1EK9
FICON license.
MDS 9100 Series
M9500FMS1K9
Fabric Manager Server package.
MDS 9500 Series
M9200FMS1K9
Fabric Manager Server package.
MDS 9200 Series
M9100FMS1K9
Fabric Manager Server package.
MDS 9100 Series
M9500EXT1K9
SAN Extension over IP package for IPS-8 module.
MDS 9500 Series
M9200EXT1K9
SAN Extension over IP package for IPS-8 module.
MDS 9200 Series
License
M9500EXT14K9
SAN Extension over IP package for IPS-4 module.
MDS 9500 Series
M9200EXT14K9
SAN Extension over IP package for IPS-4 module.
MDS 9200 Series
M9500EXT12K9
SAN Extension over IP package for MPS-14/2 module.
MDS 9500 Series
M9200EXT12K9
SAN Extension over IP package for MPS-14/2 module.
MDS 9200 Series
M9500EXT1AK9
SAN Extension over IP package for MSM-18/4 module or MSFM-18/4 FIPS module.
MDS 9500 Series
M9200EXT1AK9
SAN Extension over IP package for MSM-18/4 module or MSFM-18/4 FIPS module.
MDS 9200 Series
M9500SSE1K9
Storage Services Enabler package.
MDS 9500 Series with SSM
M9200SSE1K9
Storage Services Enabler package.
MDS 9200 Series with SSM
M9500SME1MK9
Cisco Storage Media Encryption package for MSM-18/4 module
MDS 9500 Series with MSM
M9200SME1MK9
Cisco Storage Media Encryption package for MSM-18/4 module
MDS 9200 Series with MSM
M9200SME1FK9
Cisco Storage Media Encryption package for fixed slot
MDS 9222i Switch only
M95DMMS1K9
Data Mobility Manager (DMM)
MDS 9500 Series with SSM
M92DMMS1K9
Data Mobility Manager (DMM)
MDS 9200 Series with SSM
M95DMMTS1K9
Data Mobility Manager (DMM) for 180 days
MDS 9500 Series with SSM
M92DMMTS1K9
Data Mobility Manager (DMM) for 180 days
MDS 9200 Series with SSM
M9124PL8-4G
On-Demand Ports Activation License
MDS 9124 Switch
M9134PL8-4G
On-Demand Ports Activation License
MDS 9134 Switch
M9134PL2-10G
On-Demand Ports Activation License
MDS 9134 Switch
HP-PL12-4G
On-Demand Ports Activation License
Cisco Fabric Switch for HP c-Class BladeSystem only
IBM-PL10-4G
On-Demand Ports Activation License
Cisco Fabric Switch for IBM BladeCenter only
Chassis
DS-C9513
MDS 9513 director (13-slot modular chassis with 11 slots for switching modules, and 2 slots reserved for Supervisor 2 modules only—SFPs1 sold separately).
MDS 9513 Switch only
DS-C9509
MDS 9509 director, base configuration (9-slot modular chassis includes 7 slots for switching modules and 2 slots for supervisor modules—SFPs sold separately).
MDS 9509 Switch only
DS-C9506
MDS 9506 director (6-slot modular chassis includes 4 slots for switching modules and 2 slots for supervisor modules—SFPs sold separately).
MDS 9506 Switch only
DS-C9222i-K9
MDS 9222i Multiservice Modular Switch (includes 18 4-Gbps Fibre Channel ports and 4 Gigabit Ethernet IP storage services ports, and a modular expansion slot for Cisco MDS 9000 Family Switching and Service modules.)
MDS 9222i Switch only
DS-C9216-K9
MDS 9216 16-port semi-modular fabric switch (includes 16 1-Gbps/2-Gbps Fibre Channel ports, power supply, and expansion slot—SFPs sold separately).
MDS 9216 Switch only
DS-C9216A-K9
MDS 9216A 16-port semi-modular fabric switch (includes 16 1-Gbps/2-Gbps Fibre Channel ports, power supply, and expansion slot—SFPs sold separately).
MDS 9216A Switch only
DS-C9216i-K9
MDS 9216i 16-port semi-modular fabric switch (includes 14 1-Gbps/2-Gbps Fibre Channel ports, 2 Gigabit Ethernet ports, power supply, and expansion slot—SFPs sold separately).
MDS 9216i Switch only
DS-C9140-K9
MDS 9140 fixed configuration (non-modular) fabric switch (includes 8 full rate ports and 32 host-optimized ports).
MDS 9140 Switch only
DS-C9124-K9
MDS 9124 fixed configuration (non-modular) multilayer fabric switch (includes 8 enabled ports; an on-demand ports activation license can enable 8 additional ports, up to 24 ports).
MDS 9124 Switch only
DS-C9134-K9
MDS 9134 fixed configuration (non-modular) multilayer fabric switch (includes 24 enabled 4-Gbps ports; an on-demand ports activation license can enable 8 additional ports, up to 32 4-Gbps ports. An additional port activation license can enable 2 10-Gbps ports.).
MDS 9134 Switch only
DS-C9148-K9
Cisco MDS 9148 48-Port Multilayer Fabric Switch (1RU fixed-configuration multilayer fabric switch with 48 8-Gbps Fibre Channel ports)
MDS 9148 Switch
DS-C9120-K9
MDS 9120 fixed configuration, non-modular, fabric switch (includes4 full rate ports and 16 host-optimized ports).
MDS 9120 Switch only
DS-HP-FC-K9
Cisco Fabric Switch for HP c-Class BladeSystem (includes sixteen internal and eight external active ports and four 4-Gb SFPs installed, or eight internal and four external active ports and two 4-Gb SFPs installed).
Cisco Fabric Switch for HP c-Class BladeSystem only
DS-IBM-FC-K9
Cisco Fabric Switch for IBM BladeCenter (includes fourteen internal and six external ports)
Cisco Fabric Switch for IBM BladeCenter only
External crossbar module
DS-13SLT-FAB1
MDS 9513 crossbar fabric module.
MDS 9513 Switch only
Supervisor modules
DS-X9530-SF2-K9
MDS 9500 Supervisor-2 module.
MDS 9500 Series only
DS-X9530-SF2A-K9
MDS 9500 Supervisor-2A module.
DS-X9530-SF1-K9
MDS 9500 Supervisor/Fabric-I module.
Switching modules
DS-X9016
MDS 9000 16-port 1-Gbps/2-Gbps Fibre Channel module (SFPs sold separately).
MDS 9500 Series and 9200 Series
DS-X9032
MDS 9000 32-port 1-Gbps/2-Gbps Fibre Channel module (SFPs sold separately).
DS-X9112
MDS 9000 12-port 4-Gbps Fibre Channel module (SFPs sold separately).
MDS 9500 Series and 9200 Series, except for the MDS 9216 Switch
DS-X9124
MDS 9000 24-port 4-Gbps Fibre Channel module (SFPs sold separately).
MDS 9500 Series and 9200 Series, except for the MDS 9216 Switch
DS-X9148
MDS 9000 48-port 4-Gbps Fibre Channel module (SFPs sold separately).
MDS 9500 Series and 9200 Series, except for the MDS 9216 Switch
DS-X9704
MDS 9000 4-port 10-Gbps Fibre Channel module (SFPs sold separately)
MDS 9500 Series and 9200 Series, except for the MDS 9216 Switch
Services modules
DS-X9308-SMIP
8-port Gigabit Ethernet IP Storage services module.
MDS 9500 Series and 9200 Series
DS-X9304-SMIP
4-port Gigabit Ethernet IP Storage services module.
DS-X9032-SSM
MDS 9000 32-port 1-Gbps/2-Gbps Fibre Channel Storage Services Module (SSM).
DS-X9302-14K9
14-port Fibre Channel/2-port Gigabit Ethernet Multiprotocol Services (MPS-14/2) module.
DS-X9304-18K9
18-port Fibre Channel/4-port Gigabit Ethernet Multiservice (MSM-18/4) module.
DS-X9304-18FK9
18-port Fibre Channel/4-port Gigabit Ethernet Multiservice FIPS (MSFM-18/4) module.
Optics
DS-X2-FC10G-SR
X2/SC optics, 10-Gbps Fibre Channel for Short Reach.
MDS 9500 Series and 9200 Series, except for the MDS 9216 Switch
DS-X2-FC10G-LR
X2/SC optics, 10-Gbps Fibre Channel for Long Reach.
DS-X2-FC10G-ER
X2/SC optics, 10-Gbps Fibre Channel for Extended Reach (40 km).
DS-X2-E10G-SR
X2/SC optics, 10-Gbps Ethernet for Short Reach
DS-X2-FC10G_CX4
X2/CX-4 optics, 10-Gbps Fibre Channel, copper
LC-type fiber-optic SFP
DS-SFP-FC-2G-SW
2-Gbps/1-Gbps Fibre Channel—short wavelength SFP.
MDS 9000 Family
DS-SFP-FC-2G-LW
2-Gbps/1-Gbps Fibre Channel—long wavelength SFP.
DS-SFP-FCGE-SW
1-Gbps Ethernet and 1-Gbps/2-Gbps Fibre Channel—short wavelength SFP.
DS-SFP-FCGE-LW
1-Gbps Ethernet and 1-Gbps/2-Gbps Fibre Channel—long wavelength SFP.
DS-SFP-GE-T
1-Gbps Ethernet SFP.
DS-SFP-FC4G-SW
4-Gbps/2-Gbps/1-Gbps Fibre Channel—short wavelength SFP for DS-X91xx switching modules.
MDS 9500 Series and 9200 Series, except for the MDS 9216 Switch
DS-SFP-FC4G-MR
4-Gbps/2-Gbps/1-Gbps Fibre Channel—long wavelength SFP for DS-X91xx switching modules only. Supports distances up to 4 km.
DS-SFP-FC4G-LW
4-Gbps/2-Gbps/1-Gbps Fibre Channel—long wavelength SFP for DS-X91xx switching modules only. Supports distances up to 10 km.
CWDM2
DS-CWDM-xxxx
Gigabit Ethernet and 1-Gbps/2-Gbps/4-Gbps Fibre Channel SFP LC interface xxxx nm, where xxxx = 1470, 1490, 1510, 1530, 1550, 1570, 1590, or 1610 nm.
MDS 9000 Family
DS-CWDM-MUX-4
Add/drop multiplexer for four CWDM wavelengths.
DS-CWDM-MUX-8
Add/drop multiplexer for eight CWDM wavelengths.
DS-CWDMCHASSIS
Two slot chassis for CWDM add/drop multiplexers.
Power supplies
DS-CAC-6000W
6000-W AC power supply.
MDS 9513 only
DS-CAC-2500W
2500-W AC power supply.
MDS 9509 only
DS-CDC-2500W
2500-W DC power supply.
DS-CAC-3000W
3000-W AC power supply.
DS-CAC-4000W-US
4000-W AC power supply for US (cable attached).
DS-CAC-4000W-INT
4000-W AC power supply international (cable attached).
DS-CAC-1900W
1900-W AC power supply.
MDS 9506 only
DS-CDC-1900W
1900-W DC power supply.
DS-CAC-845W
845-W AC power supply.
MDS 9200 Series only
DS-CAC-300W
300-W3 AC power supply.
MDS 9100 Series only
CompactFlash
MEM-MDS-FLD51M
MDS 9500 supervisor CompactFlash disk, 512 MB.
MDS 9500 Series only
Port analyzer adapter
DS-PAA-2, DS-PAA
A standalone Fibre Channel-to-Ethernet adapter that allows for simple, transparent analysis of Fibre Channel traffic in a switched fabric.
MDS 9000 Family
CD-ROM
M90FMK9-CD322=
MDS 9000 Management Software and Documentation CD-ROM, spare.
MDS 9000 Family
1 SFP = small form-factor pluggable
2 CWDM = coarse wavelength division multiplexing
3 W = Watt
Software Download Process
Use the software download procedure to upgrade to a later version, or downgrade to an earlier version, of an operating system. This section describes the software download process for the Cisco MDS SAN-OS and includes the following topics:
•
•
•
•
•
Determining the Software Version
To determine the version of Cisco MDS SAN-OS software currently running on a Cisco MDS 9000 Family switch using the CLI, log in to the switch and enter the show version EXEC command.
To determine the version of Cisco MDS SAN-OS software currently running on a Cisco MDS 9000 Family switch using the Fabric Manager, view the Switches tab in the Information pane, locate the switch using the IP address, logical name, or WWN, and check its version in the Release column.
Determining Software Version Compatibility
Table 3 lists the software versions that are compatible in a mixed SAN environment, and the minimum software versions that are supported. We recommend that you use the latest software release supported by your vendor for all Cisco MDS 9000 Family products.
Downloading Software
The Cisco MDS SAN-OS software is designed for mission-critical high availability environments. To realize the benefits of nondisruptive upgrades on the Cisco MDS 9500 Directors, we highly recommend that you install dual supervisor modules.
To download the latest Cisco MDS SAN-OS software, access the Software Center at this URL:
http://www.cisco.com/public/sw-center
See the following sections in this release note for details on how you can nondisruptively upgrade your Cisco MDS 9000 switch. Issuing the install all command from the CLI, or using Fabric Manager to perform the downgrade, enables the compatibility check. The check indicates if the upgrade can happen nondisruptively or disruptively depending on the current configuration of your switch and the reason.
Compatibility check is done:Module bootable Impact Install-type Reason------ -------- -------------- ------------ ------1 yes non-disruptive rolling2 yes disruptive rolling Hitless upgrade is not supported3 yes disruptive rolling Hitless upgrade is not supported4 yes non-disruptive rolling5 yes non-disruptive reset6 yes non-disruptive resetAt a minimum, you need to disable the default device alias distribution feature using the no device-alias distribute command in global configuration mode. The show incompatibility system bootflash:1.3(x)_filename command determines which additional features need to be disabled.
Note
Note
Selecting the Correct Software Image for an MDS 9100 Series Switch
The system and kickstart image that you use for an MDS 9100 series switch depends on which switch you use, as shown in Table 4.
Selecting the Correct Software Image for an MDS 9200 Series Switch
The system and kickstart image that you use for an MDS 9200 series switch depends on which switch you use, as shown in Table 5.
Table 5 Software Images for MDS 9200 Series Switches
MDS 9222i
Filename begins with m9200-s2ek9
MDS 9216A or MDS 9216i
Filename begins with m9200-ek9
Selecting the Correct Software Image for an MDS 9500 Series Switch
The system and kickstart image that you use for an MDS 9500 Series switch depends on whether the switch is based on a Supervisor-1 module or a Supervisor-2 module, as shown in Table 6.
Use the show module command to display the type of supervisor module in the switch. For a Supervisor-1 module, the output might look like this:
switch# show moduleMod Ports Module-Type Model Status--- ----- -------------------------------- ------------------ ------------......5 0 Supervisor/Fabric-1 DS-X9530-SF1-K9 active*6 0 Supervisor/Fabric-1 DS-X9530-SF1-K9 ha-standbyFor a Supervisor-2 module, the output might look like this:
switch# show moduleMod Ports Module-Type Model Status--- ----- -------------------------------- ------------------ ------------......7 0 Supervisor/Fabric-2 DS-X9530-SF2-K9 active *8 0 Supervisor/Fabric-2 DS-X9530-SF2-K9 ha-standbyMigrating from Supervisor-1 Modules to Supervisor-2 Modules
As of Cisco MDS SAN-OS Release 3.0(1), the Cisco MDS 9509 and 9506 Directors support both Supervisor-1 and Supervisor-2 modules. Supervisor-1 and Supervisor-2 modules cannot be installed in the same switch, except during migration. Both the active and standby supervisor modules must be of the same type, either Supervisor-1 or Supervisor-2 modules. For Cisco MDS 9513 Directors, both supervisor modules must be Supervisor-2 modules.
Caution
Note
To migrate from a Supervisor-1 module to a Supervisor-2 module, refer to the step-by-step instructions in the Cisco MDS 9000 Family CLI Configuration Guide.
Configuring Generation 2 Switching Modules
The Cisco MDS 9500 Multilayer Directors are designed to operate with any combination of Cisco MDS 9000 Generation 1 and Generation 2 modules. However, there are limitations to consider when combining the various modules and supervisors in the Cisco MDS 9500 Series platform chassis. The references listed in this section provide specific information about configurations that combine different modules and supervisors.
For information on configuring Generation 2 switching modules, refer to the Configuring Generation 2 Switching Modules chapter in the Cisco MDS 9000 Family CLI Configuration Guide.
For information on port index availability, refer to the "Port Index Availability" section in the Product Overview chapter of the Cisco MDS 9500 Series Hardware Installation Guide.
For information on Cisco MDS 9000 hardware and software compatibility, refer to the Cisco MDS 9000 SAN-OS Hardware and Software Compatibility Information.
Upgrading Your Cisco MDS SAN-OS Software Image
This section lists the guidelines recommended for upgrading your Cisco MDS SAN-OS software image and contains the following sections:
•
•
•
•
•
•
•
•
Upgrading Your Version of Cisco Fabric Manager
As of Cisco SAN-OS Release 3.2(1), Cisco Fabric Manager is no longer packaged with a Cisco MDS 9000
Family switch. It is included on the CD-ROM that ships with the switch. You can install Fabric Manager from the CD-ROM or from files that you download.
Installing Cisco Fabric Manager is a multi-step process that involves installing a database, as well as Fabric Manager. The complete installation instructions are provided in the "Installation of Cisco MDS SAN-OS and Fabric Manager" section in the Cisco MDS 9000 Family Fabric Manager Configuration Guide, and are available on-screen once you launch the Fabric Manager installer from the CD-ROM.
Note
Note
Upgrading from Release 3.1(2c) with the PostgreSQL Patch
To upgrade Fabric Manager to Release 3.3(5a) from the UBS special version of 3.1.2c with the PostgreSQL patch, do the following:
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
The Fabric Manager Installation Process Overview
The following section presents the flow of the installation process at a high level. Review these guidelines before you begin the installation process.
1.
•
•
•
•
•
•
•
•
Note
•
•
Note
•
•
•
•
•
•
•
•
•
2.
If you are upgrading Cisco Fabric Manager in Cisco SAN-OS Releases 3.1(2b) and later, be aware that data is migrated from the Hypersonic HSQL database to either the PostgreSQL database or Oracle Database 10g Express during the installation. Data is also migrated from Oracle Database 10g Express to Oracle Database 10g Express. If you migrate the database from Oracle to Oracle, the schema is updated. Refer to Table 7 for information on the supported upgrade path.
3.
If you are upgrading Fabric Manager in a Cisco SAN-OS Release prior to 3.1(2b), be aware that data is migrated from the Hypersonic HSQL database to either the PostgreSQL database or the Oracle Database 10g Express during the installation. The Fabric Manager Installer installs the PostgreSQL database on Windows. If you want to install the PostgreSQL database on Solaris or Linux, or if you want to install the Oracle Database 10g Express database, follow the instructions in the "Installation of Cisco MDS SAN-OS and Fabric Manager" section in the Cisco MDS 9000 Family Fabric Manager Configuration Guide. Refer to Table 7 for information on the supported upgrade path.
4.
5.
If you want to use the Oracle Database 10g Express, you must install the database and create a user name and password before continuing with the Fabric Manager installation. We recommend the Oracle Database 10g Express option for all users who are running Performance Manager on large fabrics (1000 or more end devices).
If you want to install the PostgreSQL database, you must disable any security software you are running as PostgreSQL may not install certain folders or users. You must also log in as a Superuser before you start the installation.
6.
http://cisco.com/cgi-bin/tablebuild.pl/mds-fm
Installing Fabric Manager on Solaris
This section describes how to install Fabric Manager on Solaris.
To install Fabric Manager on Solaris, follow these steps:
Step 1
Step 2
Step 3
Step 4
java -Xms512m -Xmx512m -jar m9000-fm-3.3.5a.jar
Step 5
Note
Installing Fabric Manager on Windows
This section describes how to install Fabric Manager on Windows.
Note
Note
On a Windows system, the Microsoft Active Directory applies a Group Policy Object (GPO) to the Fabric Manager Server. The GPO does not recognize the local user PostgreSQL because it is not in the GPO allow list. As a result, the GPO removes it, and the PostgreSQL database stops working.
To avoid this situation, you should move the Fabric Manager Server to its own OU and apply the same feature settings as the original OU, but remove the local user account to log in as a service.
If your server is running Terminal Services in Application mode, or if you are running Citrix Metaframe or any variation thereof, you need to issue the following command on the DOS prompt before installing Fabric Manager Server.
1.
2.
Note
The following is an example of the output of this command:
C:\Documents and Settings\user.domain>USER /INSTALLUser session is ready to install applications.
3.
4.
The following is an example of the output of this command:
C:\Documents and Settings\user.domain>USER /executeUser session is ready to execute applications.To install Fabric Manager on Windows, follow these steps:
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
To install Device Manager on your workstation, follow these steps:
Step 1
Step 2
Step 3
Step 4
Note
General Upgrading Guidelines
Use the following guidelines when upgrading to Cisco MDS SAN-OS Release 3.3(5a):
•
•
•
•
•
–
–
–
–
–
Use Table 8 to determine your nondisruptive upgrade path to Cisco SAN-OS Release 3.3(5a). Find the image release number you are currently using in the Current column of the table and use the path recommended.
Note
•
•
If an upgrade is attempted when an active configurations is present, the switch will go into a disruptive upgrade.
Note
FICON Supported Releases and Upgrade Paths
Cisco MDS SAN-OS Release 3.3(5a) does not support FICON.
Table 9 lists the SAN-OS and NX-OS releases that support FICON. Refer to the specific release notes for FICON upgrade path information.
Table 9 FICON Supported Releases
NX-OS
Release 4.2(1b)
Release 4.1(1c)
SAN-OS
Release 3.3(1c)
Release 3.2(2c)
Release 3.0(3b)
Release 3.0(3)
Release 3.0(2)
Release 2.0(2b)
Upgrading with IVR Enabled
An Inter-Switch Link (ISL) flap resulting in fabric segmentation or a merge during or after an upgrade from Cisco MDS SAN-OS Release 2.0(x) to a later image where IVR is enabled might be disruptive. Some possible scenarios include the following:
•
•
•
If this problem occurs, syslogs indicate a failure and the flapped ISL could remain in a down state because of a domain overlap.
This issue was resolved in Cisco SAN-OS Release 2.1(2b); you must upgrade to Release 2.1(2b) before upgrading to Release 3.3(4). An upgrade from Cisco SAN-OS Releases 2.1(1a), 2.1(1b), or 2.1(2a) to Release 2.1(2b) when IVR is enabled requires that you follow the procedure below, and then follow the upgrade guidelines listed in the "Upgrading Your Version of Cisco Fabric Manager" section. If you have VSANs in interop mode 2 or 3, you must issue an IVR refresh for those VSANs.
To upgrade from Cisco SAN-OS Releases 2.1(1a), 2.1(1b), or 2.1(2a) to Release 2.1(2b) for all other VSANs with IVR enabled, follow these steps:
Step 1
Note
Step 2
Note
Step 3
2005 Aug 31 21:52:04 switch %FCDOMAIN-2-EPORT_ISOLATED:%$VSAN 2005%$ Isolation of interfaceport-channel 52 (reason: unknown failure)2005 Aug 31 21:52:04 switch %FCDOMAIN-2-EPORT_ISOLATED: %$VSAN 2005%$Isolation of interface port-channel 51(reason: domain ID assignment failure)Step 4
switch(config)# vsan databaseswitch(config-vsan-db)# vsan vsan-id suspendswitch(config-vsan-db)# no vsan vsan-id suspendStep 5
Step 6
Step 7
Note
Reconfiguring SSM Ports Before Upgrading to SAN-OS Release 3.3(5a)
Starting with Cisco MDS SAN-OS Release 3.0(1), the SSM front panel ports can no longer be configured in auto mode, which is the default for releases prior to Release 3.0(1).
Note
For more information on upgrading SAN-OS software, see the "Upgrading Your Cisco MDS SAN-OS Software Image" section.
If the configuration is not updated before the upgrade, the installation process for the new image will automatically convert all ports configured in auto mode to Fx mode. This change in mode might cause a disruption if the port is currently operating in E mode.
To upgrade the image on your SSM without any traffic disruption, follow these steps:
Step 1
switch# show interface fc 2/1 - 32fc2/1 is upHardware is Fibre Channel, SFP is short wave laser w/o OFC (SN)Port WWN is 20:4b:00:0d:ec:09:3c:00Admin port mode is auto <-------- shows port is configured in auto modesnmp traps are enabledPort mode is F, FCID is 0xef0300 <-------- shows current port operational mode is FPort vsan is 1Speed is 2 GbpsTransmit B2B Credit is 3Step 2
a.
switch# config tswitch(config)# interface fc 2/1switch(config-if)# switchport mode fxb.
switch# config tswitch(config)# interface fc 2/5switch(config-if)# switchport mode eStep 3
a.
switch# config tswitch(config)# interface fc 2/2switch(config-if)# switchport mode fxb.
switch# config tswitch(config)# interface fc 2/2switch(config-if)# shutdownStep 4
switch# copy running-config startup-config
Upgrading the SSI Image on Your SSM
Use the following guidelines to nondisruptively upgrade the SSI image on your SSM:
•
•
–
–
–
–
–
Caution
Upgrading a Switch with Insufficient Space for Two Images on the Bootflash
To upgrade the SAN-OS image on a Cisco MDS 9000 Family switch requires enough space on the internal CompactFlash (also referred to as bootflash) to accommodate both the old software image and the new software image.
As of Cisco MDS SAN-OS Release 3.1(1), on MDS switches with a 256-MB CompactFlash, it is possible in some scenarios that a user might be unable to fit two images on the bootflash. This lack of space on the bootflash might cause the upgrade process to fail because new images are always copied onto the bootflash during an upgrade.
The following MDS switches are affected by this issue:
•
•
•
To work around an image upgrade failure caused by a lack of space on the bootflash, follow these steps:
Step 1
Step 2
switch# delete bootflash:m9200-ek9-mz.3.0.3.bin
Note
switch# delete bootflash://sup-standby/m9500-sf1ek9-mz.3.0.3.binStep 3
Step 4
Step 5
Upgrading a Cisco MDS 9124 Switch
If you are upgrading from Cisco MDS SAN-OS Release 3.1(1) to Cisco SAN-OS Release 3.3(5a) on a Cisco MDS 9124 Switch, follow these guidelines:
•
•
•
•
•
•
Performing a Disruptive Upgrade on a Single Supervisor MDS Family Switch
Cisco MDS SAN-OS software upgrades are disruptive on the following single supervisor Cisco MDS Family switches:
•
•
•
If you are performing an upgrade on one of those switches, you should follow the nondisruptive upgrade path shown in Table 7, even though the upgrade is disruptive. Following the nondisruptive upgrade path ensures that the binary startup configuration remains intact.
If you do not follow the upgrade path, (for example, you upgrade directly from SAN-OS Release 2.1(2) or earlier version to SAN-OS Release 3.3(5a), the binary startup configuration is deleted because it is not compatible with the new image, and the ASCII startup configuration file is applied when the switch comes up with the new upgraded image. When the ASCII startup configuration file is applied, there may be errors. Because of this, we recommend that you follow the nondisruptive upgrade path.
Upgrading an MDS 9222i Switch
If you are running SAN-OS Release 3.3(5a) on an MDS 9222i switch and you want to upgrade to an NX-OS 4.x release, you can upgrade to release 4.1(3a) and higher. Do not attempt to upgrade an MDS 9222i switch from SAN-OS 3.3(5a) to NX-OS 4.1(1x) (including 4.1(1b) and 4.1(1c)) because the upgrade path is not supported on the MDS 9222i. This restriction does not apply to other platforms.
Before upgrading, issue the show install all impact upgrade-image CLI command to determine if your upgrade will be nondisruptive.
Following the upgrade, you may need to enable features with the feature feature-name command, such as the feature iscsi command. In SAN-OS 3.3(x) release, features are enabled with the feature-name enable command, such as the iscsi enable command.
Downgrading Your Cisco MDS SAN-OS Software Image
This section lists the guidelines recommended for downgrading your Cisco MDS SAN-OS software image and contains the following sections:
•
•
•
General Downgrading Guidelines
Use the following guidelines to nondisruptively downgrade your Cisco MDS SAN-OS Release 3.3(5a):
•
•
•
•
•
•
–
–
–
–
–
–
Use Table 10 to determine the nondisruptive downgrade path from Cisco SAN-OS Release 3.3(5a). Find the SAN-OS image you want to downgrade to in the To SAN-OS Release column of the table and use the path recommended.
Note
FICON Downgrade Paths
Cisco MDS SAN-OS Release 3.3(5a) does not support FICON.
Refer to Table 9 for a list SAN-OS and NX-OS releases that support FICON. Refer to the specific release notes for FICON downgrade path information.
Downgrading the SSI Image on Your SSM
Use the following guidelines when downgrading your SSI image on your SSM.
•
•
•
•
–
–
–
Downgrading an MDS 9222i Switch
If you are running MDS NX-OS 4.1(1x) on an MDS 9222i switch and you need to downgrade to a SAN-OS 3.3(x) release, you can downgrade to Release 3.3(2), 3.3(1c), or 3.3(1a), but you cannot downgrade to 3.3(5a). A nondisruptive downgrade from NX-OS 4.1(1x) to SAN-OS 3.3(5a) is not supported on the MDS 9222i switch. This restriction does not apply to other platforms.
Before downgrading, disable all features not supported by the downgrade release. Use the show incompatibility system downgrade-image CLI command to determine what features you need to disable.
Following the downgrade, you will need to enable features with the feature-name enable command, such as the iscsi enable command. In NX-OS 4.1(x) releases, features are enabled with the feature feature-name command, such as the feature iscsi command.
New Features in Cisco MDS SAN-OS Release 3.3(5a)
This section briefly describes the new features introduced in this release. For detailed information about the features listed, refer to the Cisco MDS 9000 Family CLI Configuration Guide, Release 3.x, the Cisco MDS 9000 Family Fabric Manager Configuration Guide, and the Cisco MDS 9000 Family Storage Media Encryption Configuration Guide. For information about new CLI commands associated with these features, refer to the Cisco MDS 9000 Family Command Reference. The "New and Changed Information" section in each of these books provides a detailed list of all new features and includes links to the feature description or new command.
Note
Cisco MDS SAN-OS Release 3.3(5a) is a maintenance release that includes bug fixes. Cisco MDS SAN-OS Release 3.3(5a) also supports the discovery of the Cisco MDS 9500 Series Supervisor-2A module by Device Manager.
Limitations and Restrictions
This section lists the limitations and restrictions for this release. This section includes the following topics:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Upgrading to Recover Loss of Performance Manager Data
Caution
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Maximum Number of Zones Supported in Interop Mode 4
In interop mode 4, the maximum number of zones that is supported in an active zone set is 2047, due to limitations in the connected vendor switch.
When IVR is used in interop mode 4, the maximum number of zones supported, including IVR zones, in the active zone set is 2047.
Upgrading the SAN-OS Software on the MDS 9222i Switch
On an MDS 9222i switch, an upgrade from SAN-OS Release 3.2(x), Release 3.3(1a), or Release 3.3(1c) to SAN-OS Release 3.3(5a) fails when there is an active FC-Redirect configuration (created by Cisco SME or Cisco DMM applications) on the switch. An active FC-Redirect configuration is defined as:
FC-Redirect configuration for hosts or target connected locally
FC-Redirect configuration created by application running on that switch.
If an upgrade is attempted when an active configurations is present, the switch will go into a disruptive upgrade.
Java Web Start
When using Java Web Start, it is recommended that you do not use an HTML cache or proxy server. You can use the Java Web Start Preferences panel to view or edit the proxy configuration. To do this, launch the Application Manager, either by clicking the desktop icon (Microsoft Windows), or type ./javaws in the Java Web Start installation directory (Solaris Operating Environment and Linux), and then select Edit>Preferences.
If you fail to change these settings, you may encounter installation issues regarding a version mismatch. If this occurs, you should clear your Java cache and retry.
Cisco Storage Media Encryption
The following limitations are described for Cisco SME:
•
•
Cisco SME Configuration Limits
Table 11 lists the Cisco SME configuration limits for this release.
Deleting Cisco SME Interfaces
A Cisco SME interface can be deleted from the cluster only after the interface is administratively shut-down and all related tasks associated with the interface shut-down are complete.
Emulex Driver Version
In some instances, the Emulex driver version 8.1.10.9 may set the task attribute to HEAD_OF_QUEUE instead of SIMPLE_QUEUE. Certain tape drives do not accept this attribute and may reject these commands. The Emulex driver version 8.1.10.12 does not have this issue.
Cisco MDS 9222i Module Upgrade
On the MDS 9222i module, an upgrade from SAN-OS Release 3.2(x) to Release 3.3(1c) is not supported if there is a Cisco SME or Cisco DMM configuration in the fabric for hosts and targets attached to the MDS 9222i module.
SANTap
The SANTap feature allows third party data storage applications, such as long distance replication and continuous backup, to be integrated into the SAN.
Deleting SANTap Configurations Is Required Before Downgrade
If you are running Cisco MDS NX-OS Release 4.1(1b) in combination with the SSI 4.1(1b) image and you wish to downgrade to Cisco SAN-OS Release 3.3(5a) and an SSI 3.2(3*) image, you must delete all SANTap configurations prior to the downgrade. Downgrading without completely deleting the SANTap configurations is not supported.
FCIP Interoperability
FCIP interoperability fails between two MDS switches, one running MDS NX-OS Release 4.1(1c) and the other running MDS SAN-OS Release 3.3(5a), if the IP ACL configuration for an IPsec crypto map specifies TCP as the protocol, as in the following example:
switch(config)# ip access-list acl-name permit tcp local-gige-ip-address local-mask remote-gige-ipaddress remote-maskFCIP interoperability does not fail if the IP ACL uses IP as the protocol, as in the following example:
switch(config)# ip access-list acl-name permit ip local-gige-ip-address local-mask remote-gige-ipaddress remote-maskApplying Zone Configurations to VSAN 1
In the setup script, you can configure system default values for the default-zone to be permit or deny, and you can configure default values for the zone distribution method and for the zone mode.
These default settings are applied when a VSAN is created. However, the settings will not take effect on VSAN 1, because it exists prior to running the setup script. Therefore, when you need these settings for VSAN 1, you must explicitly issue the following commands:
•
•
•
Running Storage Applications on the MSM-18/4
The Cisco MDS 9000 18/4-Port Multiservice Module (MSM-18/4) does not support multiple, concurrent storage applications. Only one application, such as SME or DMM, can run on the MSM-18/4 at a time.
Compatibility of Fabric Manager and Data Mobility Manager
Cisco Fabric Manager in any Cisco MDS Release NX-OS 4.1(x) does not support Data Mobility Manager (DMM) in any SAN-OS Release 3.3(x) or in any SAN-OS Release 3.2(x). To use the Cisco Fabric Manager GUI for DMM, both Cisco Fabric Manager and DMM must be running Cisco NX-OS or SAN-OS software from the same release series.
A Supervisor-2 Module Might Reset in Switches Running SAN-OS Release 3.2(x)
An MDS 9000 switch with a Supervisor-2 module might switch over to the standby supervisor module with a reset reason of Kernel Panic. Although there is no workaround for this issue, it happens very rarely. Additional instrumentation and checks have been added to SAN-OS Release 3.3(1c) and later and to NX-OS Release 4.2(x) to ensure that kernel panic does not occur. DDTS CSCsx18173 describes this issue.
Limited ISSU Support on the MDS 9222i Switch
An in-service software upgrade (ISSU) from SAN-OS Release 3.3(5a) to NX-OS Release 4.1(1b) or to NX-OS Release 4.1(1c) is not supported on the MDS 9222i switch. This limitation applies only to the MDS 9222i switch. You can perform an ISSU from SAN-OS Release 3.3(5a) to NX-OS Release 4.1(1b) or NX-OS Release 4.1(1c) on other MDS switches.
ISSU upgrades from SAN-OS Release 3.3(5) to NX-OS Release 4.1(3a) and to NX-OS Release 4.13(a) are supported on the MDS 9222i switch.
PPRC Not Supported with FCIP Write Acceleration
IBM Peer to Peer Remote Copy (PPRC) is not supported with FCIP Write Acceleration.
Using IVR In a Fabric With Mixed Code Versions
If you are using IVR and you are running SAN-OS 3.x software on your MDS switches, make sure that all IVR switches run the same code version. Otherwise, if you have a fabric with mixed code versions, the switches running the higher version may not be able to see all IVR devices. The mixed fabric can cause an inconsistent database among IVR switches, which might affect IVR behavior. For this reason, it is important that all IVR switches run the same SAN-OS version, preferably SAN-OS Release 3.3(4a), which has device update (DU) support, or later.
HTTP Transport Method Not Supported in Call Home
Cisco SAN-OS Release 3.x does not support the HTTP transport method in the Call Home feature.
Caveats
This section lists the open and resolved caveats for this release. Use Table 12 to determine the status of a particular caveat. In the table, "O" indicates an open caveat and "R" indicates a resolved caveat.
Resolved Caveats
•
Symptom: When stale, non-advertised IVR virtual domain entries get stuck after an HA failover, upgrading switches with these stale entries to SAN-OS Release 3.3(2) or later may fail to clear up these entries. In some corner cases, the unexpected location of the Persistent Storage Service (PSS) cursor occurs, which can lead to IVR zone set activation failures. The cursor location should be maintained by PSS not by IVR. After each deletion, the cursor location is moved automatically by PSS.
Workaround: This issue is resolved.
•
Symptom: On a Cisco MDS 9222i switch, if in-order-delivery is enabled on one or more VSANs carried over an FCIP trunk, disabling one or more Gigabit Ethernet interfaces used for FCIP can cause a module exception similar to the following:
******** Exception info for module 1 ********exception information --- exception instance 1 ----Module Slot Number: 1Device Id : 54Device Name : Tuscany-xbarDevice Errorcode : 0xc3600107Device ID : 54 (0x36)Device Instance : 00 (0x00)Dev Type (HW/SW) : 01 (0x01)ErrNum (devInfo) : 07 (0x07)System Errorcode : 0x40420031 Tuscany xbar module experienced an errorError Type : Minor errorPhyPortLayer : Fibre Channel VirtualPort(s) Affected : 19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34Error Description :DSAP : 0 (0x0)UUID : 0 (0x0)Time : Mon Nov 16 10:07:33 2009(Ticks: 4B012465 jiffies)exception information --- exception instance 2 ----Module Slot Number: 1Device Id : 54Device Name : Tuscany-xbarDevice Errorcode : 0xc3600107Device ID : 54 (0x36)Device Instance : 00 (0x00)Dev Type (HW/SW) : 01 (0x01)ErrNum (devInfo) : 07 (0x07)System Errorcode : 0x40420031 Tuscany xbar module experienced an errorError Type : Minor errorPhyPortLayer : Fibre ChannelPort(s) Affected : 1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18Error Description :DSAP : 0 (0x0)UUID : 0 (0x0)Time : Mon Nov 16 10:07:33 2009(Ticks: 4B012465 jiffies)All FC and FCIP interfaces go to the hwFailure state and the switch or module needs to be reloaded to recover.
Workaround: This issue is resolved.
•
Symptom: The adjacencies offset in an ACL was computed incorrectly.
Workaround: This issue is resolved.
•
Symptom: Fabric discovery failed because of an internal error when one or more VSANs were suspended.
Workaround: This issue is resolved.
•
Symptom: Under certain conditions, the port manager can take a long time to respond to a port configuration, which can trigger a set-port-configuration failure. If this occurs, then the FCIP tunnel will not come up and will stay in a disabled state.
Workaround: This issue is resolved.
•
Symptom: A bitmap print buffer overflow caused an SNMP process to fail.
Workaround: This issue is resolved.
•
Symptom: Following an upgrade from SAN-OS Release 3.0(2a) to Release 3.3(2), IVR zoneset activation does not go through successfully in an IVR1 (non-NAT) configuration. CFS error messages similar to the following might be displayed:
******** Exception info for module 1 ********Workaround: This issue is resolved.
•
Symptom: When the EOBC of a Generation 1 supervisor module is heavily used, the supervisor module will reload.
Workaround: This issue is resolved.
•
Symptom: In a two switch setup, the host and target are connected to the same switch, and a VSAN is used on the second switch as a transit VSAN. After the transit VSAN is removed from the IVR topology and the ISL is disconnected between the two switches, the host cannot reach the tape device. In addition, the route for this SID/DID pair has not been changed, and it goes to the deleted VSAN.
Workaround: This issue is resolved.
•
Symptom: ISCI sessions are dropped over a period of time because the mbuffer gets low and session reconnections do not succeed.
Workaround: This issue is resolved.
•
Symptom: For IVR enabled switches running SAN-OS Release 3.3(2) or NX-OS Release 4.1(3a), some host initiators lose their access to the target even though they are correctly zoned for IVR. The IVR zone set active status is successful, but the device is offline in IVR pv.
Workaround: This issue is resolved.
Open Caveats
•
Symptom: iSCSi I/O running in network conditions involving latency of 2 ms or more might stop because of an Octeon process failure.
Workaround: Restart the I/O.
Related Documentation
The documentation set for the Cisco MDS 9000 Family includes the following documents. To find a document online, use the Cisco MDS SAN-OS Documentation Locator at:
http://www.cisco.com/en/US/products/ps5989/products_documentation_roadmaps_list.htm
For information on IBM TotalStorage SAN Volume Controller Storage Software for the Cisco MDS 9000 Family, refer to the IBM TotalStorage Support website.
Release Notes
•
•
•
Compatibility Information
•
•
•
•
Regulatory Compliance and Safety Information
•
Hardware Installation
•
•
•
•
•
•
•
Cisco Fabric Manager
•
•
•
•
Command-Line Interface
•
•
•
•
•
•
•
Intelligent Storage Networking Services
•
•
•
Troubleshooting and Reference
•
•
•
•
•
•
Installation and Configuration Note
•
•
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.
This document is to be used in conjunction with the documents listed in the "Related Documentation" section.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.
© 2010 Cisco Systems, Inc. All rights reserved.
