Table Of Contents
SAN Interconnect Device Matrix
Cisco Devices
Switch Interoperability Matrix
NPV
IBM eServer Bladecenter Interoperability Matrix
NPV Interoperability Matrix
SAN Interconnect Device Matrix
This chapter lists devices tested by Cisco Solution-Interoperability Engineering group (iLAB) used for connecting SAN islands over metropolitan networks (MAN) and wide area networks (WAN).
•Cisco Devices
•Switch Interoperability Matrix
•NPV
•IBM eServer Bladecenter Interoperability Matrix
•NPV Interoperability Matrix
Cisco Devices
Table 4-1 Cisco System Ethernet/ MAN/WAN Device Status
Vendor
MAN/WAN Device
Protocol
Qualified
Cisco Systems
Storage Router 5420, 5428, 5428-2
FC, iSCSI
Yes
Cisco Systems
ONS 1553/15540/15252/15454
FC
Cisco Systems
Cisco 1000Base cWDM GBICs + Add/Drop Modules
FC
Cisco Systems
IPS-4, IPS-8, MPS-14/2, MDS9216i, MDS9222i, MPS 18/4
iSCSI, FCIP
Cisco Systems
Cisco 7000 Router w/Port Adapter Module (PAM)
FC
Switch Interoperability Matrix
The switch Interoperability test was performed per the Fibre Channel Methodologies for Interconnect (FC-MI) Technical Report version 1.92 which describes common methodologies for facilitating interoperability in a heterogeneous switch SAN environment.
The MDS family is SANmark 3001and 3002 qualified.
IBM Supports MDS InterOp Mode-1 (FC-MI standard), Mode-2 (Brocade PID=0), Mode-3 (Brocade PID=1), and Mode-4 (McDATA native). Please refer to the following IBM documnet for more information:
f tp://service.boulder.ibm.com/storage/san/cisco/mds9216.pdf
EMC Supports all MDS InterOp Modes with Brocade and McDATA outlined in the Switched Fabric Topology Parameters section EMC Support Matrix:
http://www.emc.com/collateral/elab/emc-support-matrices.pdf
HDS Supports MDS InterOp Mode-1 with Brocade and McDATA
HP Supports MDS InterOp Mode-1 with Brocade and McDATA, refer to the below link for more information:
http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00758719/c00758719.pdf
Table 4-2 Switch Interoperability Matrix
Switch Vendor
Switch Models
Firmware Version
Cisco SAN-OS Version
Interop Mode
Brocade
2400, 2800
2.6.0j
1.2(1b)
11 , 22
2.6.1a
1.2(1a)
2.6.1c
1.2(1b)
2.6.2
1.3(4a)
2.6.2b
2.0(1b)
2.1(1a)
1, 2, 33
200E
5.1.0d
3.1.2b,
4.1(1a), 4.1(1b)
1, 3
3800
3.02k
1.2(1a)
1, 2
3.1.1
1.2(1a)
3.1.1c
1.2(1b)
3.1.2
1.3(4a)
3.1.3a
2.0(1b) 2.1(1a) 3.0(1) 3.0(2a) 3.0(2) 3.0(3) 3.1(2) 3.1(3)
1, 2, 3
3.2.1c
3.2(3a)
3.3(1a), 3.3(1c)
3900
4.0.2d
1.2(1a)
1
4.1.1
4.1.2b
1.2(1b)
4.2.0b
1.3(4a)
1, 3
4.2.2a
2.0(1b) 2.1(1a) 3.0(2a) 3.0(3)
4.4.0f
3.0(1) 3.0(2) 3.0(2a) 3.0(3)
4.4.0f
3.1(2) 3.1(3)
3.2(1a)
1, 2, 3
Brocade (continued)
3900
5.0.3 5.0.3b 5.0(3)
3.0(1) 3.0(2) 3.0(2a) 3.0(3)
1, 3
5.1.0d
3.1(2) 3.1.3
3.2(1a)
1, 2, 3
5.3.0
3.2(1a)
1
5.3.0b
3.2(3a)
3.3(1a), 3.3(1c),
4.1(1a), 4.1(1b)
1, 3
48000, 3850, 41004
5.0.3 5.0.3b 5.0(3)
3.0(1) 3.0(2) 3.0(2a) 3.0(3)
1, 3
5.3.0
3.2(1a)
1
5.3.0b
3.2(3a)
3.3(1a), 3.3(1c), 4.1(1a), 4.1(1b)
1, 3
4012, 4024
5.3.0b
3.3(1a), 3.3(1c)
1, 3
12000
5.0.5c
3.2(3a)
3.3(1a), 3.3(1c), 4.1(1a), 4.1(1b)
1, 3
24000
5.1.0d
3.1(2), 3.2(1a)
1, 2, 3
5.3.0b
3.2(3a)
3.3(1a), 3.3(1c), 4.1(1a), 4.1(1b)
1, 3
QLogic
SANbox2
1.4.0.43-0
1.3(4a)
Native
SAN box 5200
6.0
2.1(2b)
SANbox64
1.5.1.04
1.3(4a)
2.01
1.3(4a)
SANbox 5600
5.0.1.10.00
3.0(2a) 3.0(3)
Cisco
NX-5020
4.0(0)N1(1)
3.2(3a)/FM 3.4(1)
Native
McDATA
6064, 6140, 4500, 3232
4.01
1.2(1a)
1
5.0.1
1.2(1b)
5.0.2
1.2(1a)
1.3(4a)
6.0
1.3(4a)
6.01
6.02
2.0(1b)
7.0
2.1(1a)
7.1.0.5
4500, 6140, 6064
7.1.0.5
3.0(1) 3.0(2a)
1, 45
8.1.014
3.0(1) 3.0(2a) 3.1(2)
9.00
3.0(3) 3.1(2) 3.1(3)
9.01
3.0(3), 3.2(1a)
9.06
3.2(1a)
9.06.00 22
3.2(3a)
4.1(1a), 4.1(1b)
9.07.01.4
3.3(1a), 3.3(1c)
4.1(1a), 4.1(1b)
3032
9.07.01.4
3.3(1a), 3.3(1c)
i10k
9.2.0.8
3.2(2c), 3.2(3), 3.2(3a)
9.7.1.5
3.3(1a), 3.3(1c), 4.1(1a), 4.1(1b)
6064/6140 with 10G w/XPM card
9.06.00 22
9.07.01.4
3.2(3a)
3.3(1a), 3.3(1c), 4.1(1a), 4.1(1b)
Inrange
FC/9000
04.00.04.06
1.3(4a)
No Interop Setting required
NPV
The table below lists the OSM Qualified SAN-OS versions that supportNPV.
Table 4-3 SAN-OS Versions Supporting NPV
Connecting to >>>
Cisco Core
Brocade Core
McData Core
MDS 9200
MDS 9500
IBM Blade Switch
SAN-OS 3.2(2c), SAN-OS 3.3(1c)
SAN-OS 3.2(2c), SAN-OS 3.3(1c)
SAN-OS 3.2(2c), SAN-OS 3.3(1c)
SAN-OS 3.2(2c), SAN-OS 3.3(1c)
HP Blade Switch
SAN-OS 3.2(1a) SAN-OS 3.3(1c)
SAN-OS 3.2(1a), SAN-OS 3.3(1c)
SAN-OS 3.2(1a), SAN-OS 3.3(1c)
SAN-OS 3.2(1a), SAN-OS 3.3(1c)
IBM eServer Bladecenter Interoperability Matrix
.
Table 4-4 MDS Interoperability with IBM eServer Bladecenter
Blade SW Module Firmware
2062-D07, T07,D04, T04
(MDS 9500)
Firmware
2054-E11
(MDS9513) Firmware
2062-D01/2061-020/040
(MDS9200/9100) Firmware
2053-424 (MDS9124)
Firmware
Blade Center
2-port FC Switch Module
(No InterOp Mode Required)
2.0.1.09
1.3(2a) to 3.0(2a)
3.0(1) & 3.0(2a)
1.3(2a) to 3.0(2a)
NA
QLogic 6-port 2G Enterprise FC Switch Module
(No InterOp Mode Required)
4.1.0.22
5.5.1.10
2.1(1a) to 3.0(2a)
3.0(2a)
3.0(1) & 3.0(2a)
3.0(2a)
2.1(1a) to 3.0(2a)
3.0(2a)
NA
QLogic 6-port 4G Enterprise FC Switch Module
(No InterOp Mode Required)
5.5.1.10
3.0(2a) & higher
3.0(2a) & higher)
3.0(2a) & higher
3.1(2)
McData 6-port 2/4G FC Switch Module
(Standard Mode)
5.5.1.10
3.0(2a) & higher
(default Mode)
3.0(1) & higher
(default Mode)
3.0(2a) & higher
(default Mode)
3.1(2), 3.3(1c)
(default Mode)
Optical Pass-thru Module
NA
1.3(2a) to 3.0(2a)
3.0(1) & 3.0(2a)
1.3(2a) to 3.0(2a)
NA
Brocade Enterprise SAN Switch Module
(InterOp Mode)
4.2.1a
5.0.3a
1.3(4a), 2.0(2b), 2.1(1a)
3.0(1), 3.0(2), 3.0(2a)
(InterOp Mode 1)
3.0(2a)
(InterOp Mode 1)
1.3(4a), 2.0(2b), 2.1(1a)
3.0(1), 3.0(2), 3.0(2a)
(InterOp Mode 1)
NA)
Brocade Entry SAN Switch Module
(InterOp Mode)
Brocade Enterprise SAN Switch Module
(Native Mode)
4.2.1a
5.0.3a
1.3(4a), 2.0(2b), 2.1(1a)
3.0(1), 3.0(2), 3.0(2a)
(InterOp Mode 3)
3.0(2a)
(InterOp Mode 3)
1.3(4a), 2.0(2b), 2.1(1a)
3.0(1), 3.0(2), 3.0(2a)
(InterOp Mode 3)
NA
Brocade Entry SAN Switch Module
(Native Mode)
Brocade 4G 6-port SAN Switch Module
(InterOp Mode)
5.0.3a
3.0(1), 3.0(2), 3.0(2a) & higher
(InterOp Mode 1)
3.0(2a) & higher
(InterOp Mode 1)
3.0(1), 3.0(2), 3.0(2a) & higher
(InterOp Mode 1)
3.1(2)
(InterOp Mode 1)
Brocade 4G 6-port SAN Switch Module
(Native Mode)
5.0.3a
3.0(1), 3.0(2), 3.0(2a) & higher
(InterOp Mode 3)
3.0(2a) & higher
(InterOp Mode 3)
3.0(1), 3.0(2), 3.0(2a) & higher
(InterOp Mode 3)
3.1(2)
(InterOp Mode 3 )
Note Refer to the following URL for full IBM SAN Volume Controller compatibility information with Cisco MDS 9000 Family switches: http://www-1.ibm.com/support/docview.wss?rs=591&uid=ssg1S1002472
NPV Interoperability Matrix
.
Table 4-5 Cisco N-Port Vrtualization (NPV) InterOp Matrix
MDS 9124e Blade Switch (edge)
Switch Vendor Model
Switch Vendor Code Version
Cisco SAN-OS
Cisco MDS Switch Mode
Switch Vendor Mode
Switch Vendor
Brocade
Silkworm 3900,24000, 48000
5.3.0
3.2(1a), 3.3(1c),
4.1(1a), 4.1(1b)
Native (NPV enabled)
Native (NPIV enabled)
M6140
9.0.6
3.2(1a), 3.3(1c), 4.1(1a), 4.1(1b)