Configuring RTP Media Loopback for SIP Calls
Download this chapter
Configuring RTP Media Loopback for SIP CallsConfiguring RTP Media Loopback for SIP Calls
 Feedback

Contents

Configuring RTP Media Loopback for SIP Calls

Last Updated: March 22, 2012

RTP packets are looped back toward the source device when the RTP Media Loopback for SIP Calls feature is configured on a dial peer. The SIP RTP media loopback can be used during Cisco UBE deployments to make test calls to verify the media path between the endpoints and Cisco UBE. In a voice loopback call, an echo is heard at the device originating the call. In a video loopback call, the locally captured video and the audio echo must be rendered at the source device.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the Feature Information Table at the end of this document.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.

Prerequisites

  • Media packets must be enabled to pass through the gateway.
  • Use the media flow-through command in dial peer voice or voice service configuration mode to enable the media packets.

Cisco Unified Border Element

  • Cisco IOS Release 15.1(4)M or a later release must be installed and running on your Cisco Unified Border Element.

Cisco Unified Border Element (Enterprise)

  • Cisco IOS XE Release 3.3S or a later release must be installed and running on your Cisco ASR 1000 Series Router.

Restrictions

  • SRTP, DTLS, and STUN are not supported in loopback mode.

  • Fax (midcall transmit function change) is not supported.

  • RSVP is not supported.

  • Call transfer is not supported.

Information About RTP Media Loopback for SIP Calls

Digital Signal Processors (DSP) generate and transmit Real-time Transport Protocol (RTP) media packets from a source to a destination transport address during a SIP call session. However, when a SIP call is put on hold the DSP stops generating the RTP media packets and resumes generating and transmitting these media packets after the SIP call is resumed. This ensures that the RTP sequence number is continuous from the time of the origin to the end of a SIP call.

How to Configure RTP Media Loopback for SIP Calls

RTP packets are looped back toward the source device when the RTP Media Loopback for SIP Calls feature is configured on a dial peer. Perform this task to enable the RTP Media Loopback for SIP Calls feature on a dial peer.

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    dial-peer voice tag voip

4.    destination-pattern string

5.    session protocol sipv2

6.    session target loopback:rtp

7.    incoming called-number string

8.    exit


DETAILED STEPS
 Command or ActionPurpose
Step 1
enable


Example:

Router> enable

 

Enables privileged EXEC mode.

  • Enter your password if prompted.
 
Step 2
configure terminal


Example:

Router# configure terminal

 

Enters global configuration mode.

 
Step 3
dial-peer voice tag voip


Example:

Router(config)# dial-peer voice 77 voip

 

Specifies that the dial peer is a VoIP peer and enters dial peer voice configuration mode.

 
Step 4
destination-pattern string


Example:

Router(config-dial-peer)# destination-pattern 77

 

Specifies the prefix or the full E.164 number for the dial peer.

 
Step 5
session protocol sipv2


Example:

Router(config-dial-peer)# session protocol sipv2

 

Specifies the session protocol for calls with the SIP option.

 
Step 6
session target loopback:rtp


Example:

Router(config-dial-peer)# session target loopback:rtp

 

Designates a network-specific address to receive calls from a VoIP dial peer and configures all voice data to loop back to the source.

 
Step 7
incoming called-number string


Example:

Router(config-dial-peer)# incoming called-number 77

 

Specifies a digit string that can be matched by an incoming call to associate the call with the dial peer.

 
Step 8
exit


Example:

Router(config-dial-peer)# exit

 

Exits dial peer voice configuration mode and enters global configuration mode.

 

Configuration Examples for RTP Media Loopback

Example: Configuring Video Loopback with Cisco Telepresence System

The following sample output shows Media Loopback for SIP Calls configured on a Cisco Telepresence System (CTS). 

!
codec profile 1 aacld 
 fmtp "fmtp:96 profile-level-id=16;streamtype=5;mode=AAChbr;config=B98C00;sizeLength=13;indexLength=3;indexDeltaLength=3;constantDura
tion=480"
!
codec profile 2 h264
 fmtp "fmtp:112 profile-level-id=4D0028;sprop-parametersets=
R00AKAmWUgDwBDyA,SGE7jyA=;packetization-mode=1"
!
voice class codec 4
 codec preference 1 aacld profile 1
 video codec h264 profile 2
!
dial-peer voice 2000 voip
 destination-pattern 2000
 rtp payload-type cisco-codec-fax-ind 110
 rtp payload-type cisco-codec-aacld 96
 rtp payload-type cisco-codec-video-h264 112
 session protocol sipv2
 session target loopback:rtp
 incoming called-number 2000
 voice-class codec 4
 voice-class sip bandwidth audio tias-modifier 64000
 voice-class sip bandwidth video tias-modifier 4500000
!

Example: Configuring Video Loopback with Cisco Unified Video Advantage

The following sample output shows Media Loopback for SIP Calls configured on a Cisco Unified Video Advantage (CUVA). 

!
codec profile 3 h264
 fmtp "fmtp:98 profile-level-id=420015"
 !
voice class codec 6
 codec preference 1 g711ulaw
 video codec h264 profile 3
 !
dial-peer voice 5000 voip
 description CUVA
 destination-pattern 5000
 rtp payload-type cisco-codec-video-h264 98
 session protocol sipv2
 session target loopback:rtp
 incoming called-number 5000
 voice-class codec 6
 voice-class sip bandwidth video tias-modifier 384000

Feature Information for RTP Media Loopback for SIP Calls

The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.

Feature History Table entry for the Cisco Unified Border Element.

Table 1Feature Information for RTP Media Loopback for SIP Calls

Feature Name

Releases

Feature Information

RTP Media Loopback for SIP Calls

15.1(4)M

15.2(1)T

RTP packets are looped back toward the source when the RTP Media Loopback for SIP Calls feature is configured on a dial peer. SIP RTP media loopback helps in verifying the media path between the device originating the call and the intermediate device.

The following commands were introduced or modified: None.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

© 2012 Cisco Systems, Inc. All rights reserved.