cc/td/doc/cisintwk
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

B

B


B8ZS

binary 8-zero substitution. Line-code type, used on T1 and E1 circuits, in which a special code is substituted whenever 8 consecutive zeros are sent over the link. This code is then interpreted at the remote end of the connection. This technique guarantees ones density independent of the data stream. Sometimes called bipolar 8-zero substitution. Compare with AMI. See also ones density.

backbone

Part of a network that acts as the primary path for traffic that is most often sourced from, and destined for, other networks.

back end

Node or software program that provides services to a front end. See also client, FRF.11, and server.

backoff

The (usually random) retransmission delay enforced by contentious MAC protocols after a network node with data to transmit determines that the physical medium is already in use.

backplane

Physical connection between an interface processor or card and the data buses and the power distribution buses inside a chassis.

back pressure

Propagation of network congestion information upstream through an internetwork.

backward explicit congestion notification

See BECN.

backward learning

Algorithmic process used for routing traffic that surmises information by assuming symmetrical network conditions. For example, if node A receives a packet from node B through intermediate node C, the backward-learning routing algorithm will assume that A can optimally reach B through C.

balanced configuration

In HDLC, a point-to-point network configuration with two combined stations.

balanced, unbalanced

See balun.

balun

balanced, unbalanced. Device used for matching impedance between a balanced and an unbalanced line, usually twisted-pair and coaxial cable.

bandwidth

Difference between the highest and lowest frequencies available for network signals. The term is also used to describe the rated throughput capacity of a given network medium or protocol.

bandwidth allocation

See bandwidth reservation.

bandwidth reservation

Process of assigning bandwidth to users and applications served by a network. Involves assigning priority to different flows of traffic based on how critical and delay-sensitive they are. This makes the best use of available bandwidth, and if the network becomes congested, lower-priority traffic can be dropped. Sometimes called bandwidth allocation. See also call leg.

Banyan VINES

See VINES.

BARRNet

Bay Area Regional Research Network. Regional network serving the San Francisco Bay Area. The BARRNet backbone is composed of four University of California campuses (Berkeley, Davis, Santa Cruz, and San Francisco), Stanford University, Lawrence Livermore National Laboratory, and NASA Ames Research Center. BARRNet is now part of BBN Planet. See also BBN Planet.

baseband

Characteristic of a network technology where only one carrier frequency is used. Ethernet is an example of a baseband network. Also called narrowband. Contrast with broadband.

bash

Bourne-again shell. Interactive UNIX shell based on the traditional Bourne shell, but with increased functionality. See also root account.

basic encoding rules

See BER.

Basic Rate Interface

See BRI.

Basic Research and Human Resources

See BRHR.

baud

Unit of signaling speed equal to the number of discrete signal elements transmitted per second. Baud is synonymous with bits per second (bps) if each signal element represents exactly 1 bit.

Bay Area Regional Research Network

See BARRNet.

BBN

Bolt, Beranek, and Newman, Inc. High-technology company located in Massachusetts that developed and maintained the ARPANET (and later, the Internet) core gateway system. See also BBN Planet.

BBN Planet

Subsidiary company of BBN that operates a nationwide Internet access network composed in part by the former regional networks BARRNet, NEARNET, and SURAnet. See also BARRNet, BBN, NEARNET, and SURAnet.

Bc

Committed Burst. Negotiated tariff metric in Frame Relay internetworks. The maximum amount of data (in bits) that a Frame Relay internetwork is committed to accept and transmit at the CIR. See also Be and CIR.

B channel

bearer channel. In ISDN, a full-duplex, 64-kbps channel used to send user data. Compare to D channel, E channel, and H channel.

BCP

Best Current Practices. The newest subseries of RFCs that are written to describe BCPs in the Internet. Rather than specifying a protocol, these documents specify the best ways to use the protocols and the best ways to configure options to ensure interoperability between various vendors' products.

BDCS

Broadband Digital Cross-Connect System. SONET DCS capable of cross-connecting DS-3, STS-1 and STS-3c signals. See also DCS.

Be

excess burst. Negotiated tariff metric in Frame Relay internetworks. The number of bits that a Frame Relay internetwork will attempt to transmit after Bc is accommodated. Be data is, in general, delivered with a lower probability than Bc data because Be data can be marked as DE by the network. See also Bc and DE.

beacon

Frame from a Token Ring or FDDI device indicating a serious problem with the ring, such as a broken cable. A beacon frame contains the address of the station assumed to be down. See also failure domain.

bearer channel

See B channel.

Because It's Time Network

See BITNET.

BECN

backward explicit congestion notification. Bit set by a Frame Relay network in frames traveling in the opposite direction of frames encountering a congested path. DTE receiving frames with the BECN bit set can request that higher-level protocols take flow control action as appropriate. Compare with FE.

Bell Communications Research

See Bellcore.

Bellcore

Bell Communications Research. Organization that performs research and development on behalf of the RBOCs.

Bellman-Ford routing algorithm

See distance vector routing algorithm.

Bell operating company

See BOC.

BER

1. bit error rate. Ratio of received bits that contain errors.

2. basic encoding rules. Rules for encoding data units described in the ISO ASN.1 standard. See also
ASN.1.

Berkeley Internet Name Domain

See BIND.

Berkeley Standard Distribution

See BSD.

BERT

bit error rate tester. Device that determines the BER on a given communications channel. See also BER, bit error rate.

best-effort delivery

Describes a network system that does not use a sophisticated acknowledgment system to guarantee reliable delivery of information.

BGP

Border Gateway Protocol. Interdomain routing protocol that replaces EGP. BGP exchanges reachability information with other BGP systems. It is defined by RFC 1163. See also BGP4 and EGP.

BGP4

BGP Version 4. Version 4 of the predominant interdomain routing protocol used on the Internet. BGP4 supports CIDR and uses route aggregation mechanisms to reduce the size of routing tables. See also BGP and CIDR.

BIA

burned-in MAC address.

BICI

Broadband Inter-Carrier Interface. ITU-T standard that defines the protocols and procedures needed for establishing, maintaining, and terminating broadband switched virtual connections between public networks.

BIGA

See BIGA (Bus Interface Gate Array) in the "Cisco Systems Terms and Acronyms" section.

big-endian

Method of storing or transmitting data in which the most significant bit or byte is presented first. Compare with little-endian.

binary

Numbering system characterized by ones and zeros (1 = on, 0 = off).

binary 8-zero substitution

See B8ZS.

binary coded alternate mark inversion

See AMI.

binary synchronous communication

See BSC.

Binary Synchronous Communication Protocol

See bisync.

BIND

Berkeley Internet Name Domain. Implementation of DNS developed and distributed by the University of California at Berkeley (United States). Many Internet hosts run BIND, which is the ancestor of many commercial BIND implementations.

BinHex

Binary Hexadecimal. Method for converting binary files into ASCII for transmission by applications, such as e-mail, that can only handle ASCII.

BIP

bit interleaved parity. In ATM, a method used to monitor errors on a link. A check bit or word is sent in the link overhead for the previous block or frame. Bit errors in the payload can then be detected and reported as maintenance information.

biphase coding

Bipolar coding scheme originally developed for use in Ethernet. Clocking information is embedded into and recovered from the synchronous data stream without the need for separate clocking leads. The biphase signal contains no direct current energy.

bipolar

Electrical characteristic denoting a circuit with both negative and positive polarity. Contrast with unipolar.

bipolar 8-zero substitution

See B8ZS.

BISDN

Broadband ISDN. ITU-T communication standards designed to handle high-bandwidth applications such as video. BISDN currently uses ATM technology over SONET-based transmission circuits to provide data rates from 155 to 622 Mbps and beyond. Contrast with N-ISDN. See also BRI, ISDN, and PRI.

bisync

Binary Synchronous Communication Protocol. Character-oriented data-link protocol for applications. Contrast with Synchronous Data Link Control (SDLC).

bit

Binary digit used in the binary numbering system. Can be 0 or 1.

bit error rate

See BER.

bit error rate tester

See BERT.

bit interleaved parity

See BIP.

BITNET

"Because It's Time" Networking Services. Low-cost, low-speed academic network consisting primarily of IBM mainframes and 9600-bps leased lines. BITNET is now part of CREN. See also CREN.

BITNET III

Dial-up service providing connectivity for members of CREN. See also CREN.

bit-oriented protocol

Class of data link layer communication protocols that can transmit frames regardless of frame content. Unlike byte-oriented protocols, bit-oriented protocols provide full-duplex operation and are more efficient and reliable. Compare with byte-oriented protocol.

bit rate

Speed at which bits are transmitted, usually expressed in bits per second.

bits per second

Abbreviated bps. See also bit rate.

black hole

Routing term for an area of the internetwork where packets enter, but do not emerge, due to adverse conditions or poor system configuration within a portion of the network.

blocking

In a switching system, a condition in which no paths are available to complete a circuit. The term is also used to describe a situation in which one activity cannot begin until another is completed.

block multiplexer channel

IBM-style channel that implements the FIPS-60 channel, a U.S. channel standard. This channel is also referred to as OEMI channel and 370 block mux channel.

blower

Internal cooling fan used in larger router and switch chassis.

BLSR

Bidirectional Line Switch Ring. SONET ring architecture that provides working and protection fibers between nodes. If the working fiber between nodes is cut, traffic is automatically routed onto the protection fiber. See also SONET.

BNC connector

Standard connector used to connect IEEE 802.3 10Base2 coaxial cable to an MAU.

BNI

Broadband Network Interface.

BNM

Broadband Network Module.

BNN

boundary network node. In SNA terminology, a subarea node that provides boundary function support for adjacent peripheral nodes. This support includes sequencing, pacing, and address translation. Also called boundary node.

BOC

Bell operating company. Twenty-two local phone companies formed by the breakup of AT&T. See RBOC.

Bolt, Beranek, and Newman, Inc.

See BBN.

BOOTP

Bootstrap Protocol. Protocol used by a network node to determine the IP address of its Ethernet interfaces, in order to affect network booting.

boot programmable read-only memory

See boot PROM.

boot PROM

boot programmable read-only memory. Chip mounted on a printed circuit board used to provide executable boot instructions to a computer device.

Bootstrap Protocol

See BOOTP.

border gateway

Router that communicates with routers in other autonomous systems.

Border Gateway Protocol

See BGP.

boundary function

Capability of SNA subarea nodes to provide protocol support for attached peripheral nodes. Typically found in IBM 3745 devices.

boundary network node

See BNN.

boundary node

See BNN.

BPDU

Bridge Protocol Data Unit. Spanning-Tree Protocol hello packet that is sent out at configurable intervals to exchange information among bridges in the network. See also PDU.

BPI

baseline privacy interface.

bps

bits per second.

BPV

bipolar violation.

BPX Service Node

See BPX Service Node in the "Cisco Systems Terms and Acronyms" section.

break-out/break-in

See BOBI in the "Cisco Systems Terms and Acronyms" section.

BRHR

Basic Research and Human Resources. Component of the HPCC program designed to support research, training, and education in computer science, computer engineering, and computational science. See also HPCC.

BRF

bridge relay function.

BRI

Basic Rate Interface. ISDN interface composed of two B channels and one D channel for circuit-switched communication of voice, video, and data. Compare with PRI. See also BISDN, ISDN, and N-ISDN.

bridge

Device that connects and passes packets between two network segments that use the same communications protocol. Bridges operate at the data link layer (Layer 2) of the OSI reference model. In general, a bridge will filter, forward, or flood an incoming frame based on the MAC address of that frame. See also relay.

bridge forwarding

Process that uses entries in a filtering database to determine whether frames with a given MAC destination address can be forwarded to a given port or ports. Described in the IEEE 802.1 standard. See also IEEE 802.1.

bridge group

Bridging feature that assigns network interfaces to a particular spanning-tree group. Bridge groups can be compatible with the IEEE 802.1 or the DEC specification.

bridge number

Number that identifies each bridge in an SRB LAN. Parallel bridges must have different bridge numbers.

bridge protocol data unit

See BPDU.

bridge static filtering

Process in which a bridge maintains a filtering database consisting of static entries. Each static entry equates a MAC destination address with a port that can receive frames with this MAC destination address and a set of ports on which the frames can be transmitted. Defined in the IEEE 802.1 standard. See also IEEE 802.1.

broadband

1. Transmission system that multiplexes multiple independent signals onto one cable.

2. Telecommunications terminology: Any channel having a bandwidth greater than a voice-grade channel (4 kHz).

3. LAN terminology: A coaxial cable on which analog signaling is used. Also called wideband. Contrast with
baseband.

Broadband ISDN

See BISDN.

Broadband Network Interface

See BNI.

Broadband Network Module

See BNM.

Broadband Switch Module

See BXM.

broadcast

Data packet that will be sent to all nodes on a network. Broadcasts are identified by a broadcast address. Compare with multicast and unicast. See also broadcast address.

broadcast address

Special address reserved for sending a message to all stations. Generally, a broadcast address is a MAC destination address of all ones. Compare with multicast address and unicast address. See also broadcast.

broadcast and unknown server

See BUS.

broadcast domain

Set of all devices that will receive broadcast frames originating from any device within the set. Broadcast domains are typically bounded by routers because routers do not forward broadcast frames.

broadcast search

Propagation of a search request to all network nodes if the location of a resource is unknown to the requester. See also directed search.

broadcast storm

Undesirable network event in which many broadcasts are sent simultaneously across all network segments. A broadcast storm uses substantial network bandwidth and, typically, causes network time-outs.

brouter

Concatenation of "bridge" and "router." Used to refer to devices which perform both bridging and routing functions.

browser

GUI-based hypertext client application, such as Internet Explorer, Mosaic, and Netscape Navigator, used to access hypertext documents and other services located on innumerable remote servers throughout the WWW and Internet. See also hypertext, Internet, Mosaic, and WWW.

BSC

binary synchronous communication. Character-oriented data link layer protocol for half-duplex applications. A form of telecommunication line control that uses a standard set of transmission control characters and control character sequences, for binary synchronous transmission of binary-coded data between stations. Often referred to simply as .

BSD

Berkeley Standard Distribution. Term used to describe any of a variety of UNIX-type operating systems based on the UC Berkeley BSD operating system.

BSTUN

Block Serial Tunneling.

BT

burst tolerance. Parameter defined by the ATM Forum for ATM traffic management. For VBR connections, BT determines the size of the maximum burst of contiguous cells that can be transmitted. See also VBR.

BTU

British thermal units.

BTW

by the way. One of many short-hand phrases used in chat sessions and e-mail conversations. See also IMHO.

buffer

Storage area used for handling data in transit. Buffers are used in internetworking to compensate for differences in processing speed between network devices. Bursts of data can be stored in buffers until they can be handled by slower processing devices. Sometimes referred to as a packet buffer.

build

Create flat files that are ready for use by the signaling controller database.

burst tolerance

See BSTUN.

BUS

broadcast and unknown server. Multicast server used in ELANs that is used to flood traffic addressed to an unknown destination and to forward multicast and broadcast traffic to the appropriate clients. See also ELAN.

bus

1. Common physical signal path composed of wires or other media across which signals can be sent from one part of a computer to another. Sometimes called highway.

2. See
bus topology.

bus and tag channel

IBM channel, developed in the 1960s, incorporating copper multiwire technology. Replaced by the ESCON channel. See also ESCON channel and parallel channel.

Bus Interface Gate Array

See BIGA in the "Cisco Systems Terms and Acronyms" section.

bus topology

Linear LAN architecture in which transmissions from network stations propagate the length of the medium and are received by all other stations. Compare with ring topology, star topology, and tree topology.

BVI

Bridge Group Virtual Interface.

BX.25

AT&T implementation of X.25. See also X.25.

BXM

Broadband Switch Module.

bypass mode

Operating mode on FDDI and Token Ring networks in which an interface has been removed from the ring.

bypass relay

Allows a particular Token Ring interface to be shut down and thus effectively removed from the ring.

byte

Term used to refer to a series of consecutive binary digits that are operated upon as a unit (for example, an 8-bit byte).

byte-oriented protocol

Class of data-link communications protocols that use a specific character from the user character set to delimit frames. These protocols have largely been replaced by bit-oriented protocols. Compare with bit-oriented protocol.

byte reversal

Process of storing numeric data with the least-significant byte first. Used for integers and addresses on devices with Intel microprocessors.



hometocprevnextglossaryfeedbacksearchhelp
Posted: Tue Sep 21 15:34:05 PDT 1999
Copyright 1989-1999©Cisco Systems Inc.