採用PuTTY的VCS系列或Expressway系列Xconfig和Xstatus輸出集合
簡介
本檔案介紹如何從視訊通訊伺服器(VCS)系列和Expressway系列裝置（例如VCS-Control、VCS-Expressway、Expressway-C和Expressway-E）收集xconfig和xstatus命令的CLI輸出，思科技術協助中心(TAC)有時需要擷取這些輸出。
必要條件
需求
思科建議您瞭解以下主題：
- PuTTY或類似終端模擬軟體，例如SecureCRT、Tera Term或類似軟體。
- VCS/Expressway系列裝置的管理員帳戶使用者名稱和密碼。
- 網路路徑中允許的RJ45-D-Sub9針串列控制檯電纜或安全外殼(SSH)。
採用元件
本文中的資訊係根據以下軟體和硬體版本：
- PuTTY(訪問PuTTY下載頁面以獲取副本)。
- 本示例中使用的是運行版本7.2.1的VCS-C，該版本適用於當前的最新版本8.2.2版。
設定
通過控制檯連線
以下是您必須在PuTTY中配置串列控制檯訪問的設定示例。
- 轉到Configuration > Category > Connection > Serial，然後調整串列設定，如下所示：
- 轉至Category > Session，選擇Serial 型別作為連線型別，然後按一下Open ，如下圖所示：
通過SSH連線
更簡單的替代方法是通過SSH連線到裝置。
- 使用VCS/Expressway裝置的IP地址調整PuTTY中的設定，如以下示例所示：
- 在裝置進行PuTTY會話之前或期間，必須設定日誌記錄設定。為此，請轉到Configuration > Category > Session > Logging，然後配置設定以匹配此示例（調整檔案路徑和檔名以滿足您自己的PC和需要）：
- 連線並登入後，將顯示一個類似於此螢幕的螢幕。請按照此處指示以管理員身份登入。
- 輸入xstatus命令並按Enter鍵：
以下是按下Enter後顯示的xstatus輸出。輸出滾動過得太快，無法檢視到結尾。只要之前配置了日誌記錄，就會顯示在文本檔案中。
現在已收集xstatus命令的輸出，就可以收集xconfig命令的輸出了。 - 輸入xconfig命令並按Enter。
以下是按下enter鍵後xconfig輸出的範例。輸出滾動過得太快，無法檢視到結尾。只要之前配置了日誌記錄，就會在文本檔案中顯示。
VCS和Expressway系列x8.2
在x8.2的軟體版本中，現在在進行診斷日誌時包括xconfiguration和xstatus。
- 轉到維護>診斷>診斷日誌記錄。
- 選擇Start new log，然後選擇Immediately Stop logging。
下載的診斷日誌歸檔檔案包含以下檔案：
- loggingsnapshot.txt — 包含日誌消息，用於響應在日誌記錄期間執行的活動。
- xconf_dump.txt — 包含記錄開始時的系統配置資訊。
- xstat_dump.txt — 包含有關日誌記錄啟動時系統狀態的資訊。
- （如果相關）diagnostic_logging_tcpdump.pcap — 包含記錄期間捕獲的資料包。
- loggingsnapshot.txt — 包含日誌消息，用於響應在日誌記錄期間執行的活動。
驗證
以下是使用記錄設定儲存的文本檔案中的xstatus和xconfig輸出的示例：
xstatus
*s SystemUnit:
Product: "TANDBERG VCS"
Uptime: 24963390
SystemTime: "2014-06-19 14:58:59"
TimeZone: "US/Eastern"
LocalTime: "2014-06-19 10:58:59"
Software:
Version: "X7.2.1"
Build: "296181"
Name: "s42700"
ReleaseDate: "2012-09-25"
ReleaseKey: "****************"
Configuration:
NonTraversalCalls: 500
TraversalCalls: 200
Registrations: 2500
Expressway: False
Encryption: True
Interworking: True
FindMe: True
DeviceProvisioning: True
DualNetworkInterfaces: False
AdvancedAccountSecurity: False
StarterPack: False
EnhancedOCSCollaboration: True
Hardware:
Version: "VMWare"
SerialNumber: "********"
*s/end
*s Ethernet 1:
MacAddress: "00:50:56:A1:70:06"
Speed: 10000full
IPv4:
Address: "10.10.10.10"
SubnetMask: "255.255.255.0"
*s/end
*s Ethernet 2:
MacAddress: "00:50:56:A1:70:04"
Speed: 10000full
IPv4:
Address: "192.168.0.100"
SubnetMask: "255.255.255.0"
*s/end
*s Options:
Option 1:
Key: "116341X300-1-!!!!!!!!"
Description: "300 Non-traversal Calls"
Option 2:
Key: "116341P00-1-!!!!!!!!"
Description: "Device Provisioning"
Option 3:
Key: "116341G00-1-!!!!!!!!!"
Description: "H323-SIP Interworking Gateway"
Option 4:
Key: "116341U00-1-!!!!!!!!!"
Description: "FindMe"
Option 5:
Key: "116341C00-1-!!!!!!!!!"
Description: "Enhanced OCS Collaboration"
Option 8:
Key: "116341Y200-1-!!!!!!!!"
Description: "200 Traversal Calls"
Option 9:
Key: "116341X200-1-!!!!!!!!"
Description: "200 Non-traversal Calls"
*s/end
*s IP:
Protocol: IPv4
IPv4:
Gateway: "10.10.10.1"
*s/end
*s ExternalManager:
Status: Active
Address: "10.10.10.104"
Protocol: HTTP
URL: "tms/public/external/management/systemmanagementservice.asmx"
*s/end
*s Feedback 1:
Status: Off
*s/end
*s Feedback 2:
Status: Off
*s/end
*s Feedback 3:
Status: On
URL: "http://10.10.10.104/tms/public/feedback/code.aspx"
Expression: "/Event/CallDisconnected"
Expression: "/Event/CallConnected"
Expression: "/Event/CallFailure"
Expression: "/Event/RegistrationAdded"
Expression: "/Event/RegistrationChanged"
Expression: "/Event/ResourceUsage"
Expression: "/Event/AuthenticationFailure"
Expression: "/Status/Warnings"
*s/end
*s ResourceUsage:
Calls:
Traversal:
Current: 0
Max: 0
Total: 0
NonTraversal:
Current: 0
Max: 1
Total: 2
Registrations:
Current: 0
Max: 3
Total: 42
*s/end
*s Calls: /
*s/end
*s Zones:
DefaultZone:
Name: "DefaultZone"
Bandwidth:
LocalUsage: 0
ClusterUsage: 0
LocalZone:
DefaultSubZone:
Name: "DefaultSubZone"
Bandwidth:
LocalUsage: 0
ClusterUsage: 0
TraversalSubZone:
Name: "TraversalSubZone"
Bandwidth:
LocalUsage: 0
ClusterUsage: 0
ClusterSubZone:
Name: "ClusterSubZone"
Bandwidth:
LocalUsage: 0
ClusterUsage: 0
Searches:
Current: 0
CurrentDirected: 0
Total: 64081
Dropped: 0
MaxSubSearchExceeded: 0
MaxTargetsExceeded: 0
Zone 1:
Name: "TraversalZone"
Bandwidth:
LocalUsage: 0
ClusterUsage: 0
Status: Active
Type: TraversalClient
TraversalClient:
Peer 1:
H323:
Status: Active
Address: "10.10.10.102"
Port: 6001
LastStatusChange: "2014-04-03 09:50:35"
SIP:
Status: Active
Address: "10.10.10.102"
Port: 7001
LastStatusChange: "2014-04-03 09:49:13"
Server: "TANDBERG/4102 (X7.0)"
*s/end
*s Alternates: /
*s/end
*s Links:
Link 1:
Name: "DefaultSZtoTraversalSZ"
Bandwidth:
LocalUsage: 0
ClusterUsage: 0
Link 2:
Name: "DefaultSZtoDefaultZ"
Bandwidth:
LocalUsage: 0
ClusterUsage: 0
Link 3:
Name: "DefaultSZtoClusterSZ"
Bandwidth:
LocalUsage: 0
ClusterUsage: 0
Link 4:
Name: "TraversalSZtoDefaultZ"
Bandwidth:
LocalUsage: 0
ClusterUsage: 0
Link 5:
Name: "Zone001ToTraversalSZ"
Bandwidth:
LocalUsage: 0
ClusterUsage: 0
*s/end
*s Pipes: /
*s/end
*s Registrations: /
*s/end
*s SIP:
Ethernet 1:
IPv4:
UDP:
Status: Inactive
TCP:
Status: Active
Address: "10.10.10.10:5060"
TLS:
Status: Active
Address: "10.10.10.10:5061"
IPv6:
UDP:
Status: Inactive
TCP:
Status: Inactive
TLS:
Status: Inactive
Ethernet 2:
IPv4:
UDP:
Status: Inactive
TCP:
Status: Inactive
TLS:
Status: Inactive
IPv6:
UDP:
Status: Inactive
TCP:
Status: Inactive
TLS:
Status: Inactive
Transport:
Server 19857:
Socket:
Type: "SERV_UDP"
State: "INUSE"
ID:
Local: 85393
Global: 0
Buffer:
Input:
Length: 20000
Output:
Length: 20000
Local:
Address: "127.0.0.1:5060"
Remote:
Address: ""
Network:
Number: 1
Certificate:
Subject:
Name: ""
TLS:
Cipher:
Name: ""
Last:
Packet:
Received: 0
Close:
In: 20
Secure: False
X509:
Certificate:
Verified: False
Queue:
Max:
Size: 0
Add:
Failures: 0
Flow:
Token: ""
Server 19856:
Socket:
Type: "SERV_TCP"
State: "INUSE"
ID:
Local: 150928
Global: 1
Buffer:
Input:
Length: 0
Output:
Length: 0
Local:
Address: "127.0.0.1:5060"
Remote:
Address: ""
Network:
Number: 1
Certificate:
Subject:
Name: ""
TLS:
Cipher:
Name: ""
Last:
Packet:
Received: 0
Close:
In: 20
Secure: False
X509:
Certificate:
Verified: False
Queue:
Max:
Size: 0
Add:
Failures: 0
Flow:
Token: ""
Server 19855:
Socket:
Type: "SERV_TLS"
State: "INUSE"
ID:
Local: 216463
Global: 2
Buffer:
Input:
Length: 0
Output:
Length: 0
Local:
Address: "127.0.0.1:5061"
Remote:
Address: ""
Network:
Number: 1
Certificate:
Subject:
Name: ""
TLS:
Cipher:
Name: ""
Last:
Packet:
Received: 0
Close:
In: 20
Secure: True
X509:
Certificate:
Verified: False
Queue:
Max:
Size: 0
Add:
Failures: 0
Flow:
Token: ""
Server 19854:
Socket:
Type: "SERV_UDP"
State: "INUSE"
ID:
Local: 281998
Global: 3
Buffer:
Input:
Length: 20000
Output:
Length: 20000
Local:
Address: "[::1]:5060"
Remote:
Address: ""
Network:
Number: 1
Certificate:
Subject:
Name: ""
TLS:
Cipher:
Name: ""
Last:
Packet:
Received: 0
Close:
In: 20
Secure: False
X509:
Certificate:
Verified: False
Queue:
Max:
Size: 0
Add:
Failures: 0
Flow:
Token: ""
Server 19853:
Socket:
Type: "SERV_TCP"
State: "INUSE"
ID:
Local: 347533
Global: 4
Buffer:
Input:
Length: 0
Output:
Length: 0
Local:
Address: "[::1]:5060"
Remote:
Address: ""
Network:
Number: 1
Certificate:
Subject:
Name: ""
TLS:
Cipher:
Name: ""
Last:
Packet:
Received: 0
Close:
In: 20
Secure: False
X509:
Certificate:
Verified: False
Queue:
Max:
Size: 0
Add:
Failures: 0
Flow:
Token: ""
Server 19852:
Socket:
Type: "SERV_TLS"
State: "INUSE"
ID:
Local: 413068
Global: 5
Buffer:
Input:
Length: 0
Output:
Length: 0
Local:
Address: "[::1]:5061"
Remote:
Address: ""
Network:
Number: 1
Certificate:
Subject:
Name: ""
TLS:
Cipher:
Name: ""
Last:
Packet:
Received: 0
Close:
In: 20
Secure: True
X509:
Certificate:
Verified: False
Queue:
Max:
Size: 0
Add:
Failures: 0
Flow:
Token: ""
Server 19851:
Socket:
Type: "SERV_TCP"
State: "INUSE"
ID:
Local: 478603
Global: 6
Buffer:
Input:
Length: 0
Output:
Length: 0
Local:
Address: "10.10.10.10:5060"
Remote:
Address: ""
Network:
Number: 2
Certificate:
Subject:
Name: ""
TLS:
Cipher:
Name: ""
Last:
Packet:
Received: 0
Close:
In: 20
Secure: False
X509:
Certificate:
Verified: False
Queue:
Max:
Size: 0
Add:
Failures: 0
Flow:
Token: ""
Server 19850:
Socket:
Type: "SERV_TLS"
State: "INUSE"
ID:
Local: 544138
Global: 7
Buffer:
Input:
Length: 0
Output:
Length: 0
Local:
Address: "10.10.10.10:5061"
Remote:
Address: ""
Network:
Number: 2
Certificate:
Subject:
Name: ""
TLS:
Cipher:
Name: ""
Last:
Packet:
Received: 0
Close:
In: 20
Secure: True
X509:
Certificate:
Verified: False
Queue:
Max:
Size: 0
Add:
Failures: 0
Flow:
Token: ""
Client 7747:
Socket:
Type: "TLS_OUTG"
State: "INUSE"
ID:
Local: 825433667
Global: 654
Buffer:
Input:
Length: 5120
Output:
Length: 20000
Local:
Address: "10.10.10.10:27573"
Remote:
Address: "10.10.10.102:7001"
Network:
Number: 2
Certificate:
Subject:
Name: ""
TLS:
Cipher:
Name: "DHE-RSA-AES256-SHA"
Last:
Packet:
Received: -1798628722
Close:
In: 900
Secure: True
X509:
Certificate:
Verified: False
Queue:
Max:
Size: 1
Add:
Failures: 0
Flow:
Token: ""
*s/end
*s H323:
Registration:
Status: Active
IPv4:
Address: "10.10.10.10:1719"
CallSignaling:
Status: Active
IPv4:
Address: "10.10.10.10:1720"
Assent:
CallSignaling:
Status: Inactive
H46018:
CallSignaling:
Status: Inactive
*s/end
*s Applications:
Presence:
UserAgent:
Status: Inactive
Presentity:
Count: 0
Server:
Subscriptions:
Count: 0
Max: 0
Expired: 0
Subscribers:
Count: 0
Max: 0
Status: Inactive
Presentities:
Count: 0
Max: 0
Publications:
Presentities:
Count: 0
Max: 0
ConferenceFactory:
Status: Inactive
NextAlias: ""
External 1:
Status:
ClusterStatus:
ClusterState: "Disabled"
LastUpdate:
Time: "Time not set"
SecondsSinceLastRefresh: "1403189939"
*s/end
*s FindMeManager: /
*s/end
*s TURN:
Server:
Status: Inactive
*s/end
*s Policy: /
*s/end
OK
xcommand xconfig
*c xConfiguration Login Remote Protocol: LDAP
*c xConfiguration Login Remote LDAP Server Address: ""
*c xConfiguration Login Remote LDAP Server FQDNResolution: AddressRecord
*c xConfiguration Login Remote LDAP Server Port: 389
*c xConfiguration Login Remote LDAP VCS BindUsername: ""
*c xConfiguration Login Remote LDAP VCS BindPassword: "{cipher}XXXXXXXXXX
XXXXXXXXXXXX"
*c xConfiguration Login Remote LDAP VCS BindDN: ""
*c xConfiguration Login Remote LDAP BaseDN Accounts: ""
*c xConfiguration Login Remote LDAP BaseDN Groups: ""
*c xConfiguration Login Remote LDAP Encryption: Off
*c xConfiguration Login Remote LDAP SASL: DIGEST-MD5
*c xConfiguration Login Remote LDAP CRLCheck: None
*c xConfiguration Login Remote LDAP DirectoryType: ActiveDirectory
*c xConfiguration SystemUnit Name: "VCS1-Control"
*c xConfiguration SystemUnit Maintenance Mode: Off
*c xConfiguration Option 1 Key: "116341X300-1-!!!!!!!!"
*c xConfiguration Option 2 Key: "116341P00-1-!!!!!!!!"
*c xConfiguration Option 3 Key: "116341G00-1-!!!!!!!!!"
*c xConfiguration Option 4 Key: "116341U00-1-!!!!!!!!!"
*c xConfiguration Option 5 Key: "116341C00-1-!!!!!!!!"
*c xConfiguration Option 8 Key: "116341Y200-1-!!!!!!!!"
*c xConfiguration Option 9 Key: "116341X200-1-!!!!!!!!"
*c xConfiguration Ethernet 1 Speed: Auto
*c xConfiguration Ethernet 1 IP V4 Address: "10.10.10.10"
*c xConfiguration Ethernet 1 IP V4 SubnetMask: "255.255.255.0"
*c xConfiguration Ethernet 1 IP V6 Address: ""
*c xConfiguration Ethernet 2 Speed: Auto
*c xConfiguration Ethernet 2 IP V4 Address: "192.168.0.100"
*c xConfiguration Ethernet 2 IP V4 SubnetMask: "255.255.255.0"
*c xConfiguration Ethernet 2 IP V6 Address: ""
*c xConfiguration IPProtocol: IPv4
*c xConfiguration IP Gateway: "10.10.10.1"
*c xConfiguration IP QoS Mode: None
*c xConfiguration IP QoS Value: 0
*c xConfiguration IP V6 Gateway: ""
*c xConfiguration IP DNS Domain Name: "######.local"
*c xConfiguration IP DNS Hostname: "VCS1-Control"
*c xConfiguration IP Ephemeral PortRange Start: 40000
*c xConfiguration IP Ephemeral PortRange End: 49999
*c xConfiguration IP RFC4821 Mode: Disabled
*c xConfiguration Administration Telnet Mode: Off
*c xConfiguration Administration SSH Mode: On
*c xConfiguration Administration HTTP Mode: On
*c xConfiguration Administration HTTPS Mode: On
*c xConfiguration Administration LCDPanel Mode: On
*c xConfiguration ExternalManager Address: "10.10.10.104"
*c xConfiguration ExternalManager Path: "tms/public/external/management/system
managementservice.asmx"
*c xConfiguration ExternalManager Protocol: HTTP
*c xConfiguration ExternalManager Server Certificate Verification Mode: On
*c xConfiguration Registration RestrictionPolicy Mode: None
*c xConfiguration Registration RestrictionPolicy Service Protocol: HTTP
*c xConfiguration Registration RestrictionPolicy Service TLS Verify Mode: On
*c xConfiguration Registration RestrictionPolicy Service TLS CRLCheck Mode: Off
*c xConfiguration Registration RestrictionPolicy Service Server 1 Address: ""
*c xConfiguration Registration RestrictionPolicy Service Server 2 Address: ""
*c xConfiguration Registration RestrictionPolicy Service Server 3 Address: ""
*c xConfiguration Registration RestrictionPolicy Service Path: ""
*c xConfiguration Registration RestrictionPolicy Service Status Path: "status"
*c xConfiguration Registration RestrictionPolicy Service UserName: ""
*c xConfiguration Registration RestrictionPolicy Service Password: "{cipher}
XXXXXXXXXXXXXXXXXXXXX"
*c xConfiguration Registration RestrictionPolicy Service DefaultCPL: "<reject
status='504' reason='Registration Policy Unavailable'/>"
*c xConfiguration Alternates ConfigurationMaster: 1
*c xConfiguration Alternates Cluster Name: ""
*c xConfiguration Alternates Peer 1 Address: ""
*c xConfiguration Alternates Peer 2 Address: ""
*c xConfiguration Alternates Peer 3 Address: ""
*c xConfiguration Alternates Peer 4 Address: ""
*c xConfiguration Alternates Peer 5 Address: ""
*c xConfiguration Alternates Peer 6 Address: ""
*c xConfiguration Transform 1 Description: "Transform destination aliases to
URI format"
*c xConfiguration Transform 1 State: Enabled
*c xConfiguration Transform 1 Priority: 1
*c xConfiguration Transform 1 Pattern String: "([^@]*)"
*c xConfiguration Transform 1 Pattern Type: Regex
*c xConfiguration Transform 1 Pattern Behavior: Replace
*c xConfiguration Transform 1 Pattern Replace: "\1@#####.local"
*c xConfiguration Call Loop Detection Mode: On
*c xConfiguration Call Routed Mode: Always
*c xConfiguration Call Services CallsToUnknownIPAddresses: Indirect
*c xConfiguration Call Services Fallback Alias: ""
*c xConfiguration H323 Mode: On
*c xConfiguration H323 Gatekeeper Registration UDP Port: 1719
*c xConfiguration H323 Gatekeeper Registration ConflictMode: Reject
*c xConfiguration H323 Gatekeeper CallSignaling TCP Port: 1720
*c xConfiguration H323 Gatekeeper CallSignaling PortRange Start: 15000
*c xConfiguration H323 Gatekeeper CallSignaling PortRange End: 19999
*c xConfiguration H323 Gatekeeper TimeToLive: 1800
*c xConfiguration H323 Gatekeeper CallTimeToLive: 120
*c xConfiguration H323 Gatekeeper AutoDiscovery Mode: On
*c xConfiguration H323 Gateway CallerId: ExcludePrefix
*c xConfiguration SIP Mode: On
*c xConfiguration SIP Domains Domain 1 Name: "######.com"
*c xConfiguration SIP Domains Domain 2 Name: "######.local"
*c xConfiguration SIP Routes Route 1 Method: "SUBSCRIBE"
*c xConfiguration SIP Routes Route 1 Request Line Pattern: ".*@(%localdomains%|
%ip%)"
*c xConfiguration SIP Routes Route 1 Header Name: "Event"
*c xConfiguration SIP Routes Route 1 Header Pattern: "(ua-profile|phonebook).*"
*c xConfiguration SIP Routes Route 1 Authenticated: Off
*c xConfiguration SIP Routes Route 1 Address: "127.0.0.1"
*c xConfiguration SIP Routes Route 1 Port: 22400
*c xConfiguration SIP Routes Route 1 Transport: TCP
*c xConfiguration SIP Routes Route 1 Tag: "Provisioning"
*c xConfiguration SIP Routes Route 2 Method: "INFO"
*c xConfiguration SIP Routes Route 2 Request Line Pattern: ".*@(%localdomains%|
%ip%)"
*c xConfiguration SIP Routes Route 2 Header Name: "Content-Type"
*c xConfiguration SIP Routes Route 2 Header Pattern: "application/tandberg-
phonebook\+xml"
*c xConfiguration SIP Routes Route 2 Authenticated: Off
*c xConfiguration SIP Routes Route 2 Address: "127.0.0.1"
*c xConfiguration SIP Routes Route 2 Port: 22400
*c xConfiguration SIP Routes Route 2 Transport: TCP
*c xConfiguration SIP Routes Route 2 Tag: "Phonebook"
*c xConfiguration SIP Registration Standard Refresh Strategy: Maximum
*c xConfiguration SIP Registration Standard Refresh Minimum: 45
*c xConfiguration SIP Registration Standard Refresh Maximum: 60
*c xConfiguration SIP Registration Outbound Refresh Strategy: Variable
*c xConfiguration SIP Registration Outbound Refresh Minimum: 300
*c xConfiguration SIP Registration Outbound Refresh Maximum: 3600
*c xConfiguration SIP Registration Outbound Flow Timer: 0
*c xConfiguration SIP Registration Proxy Mode: Off
*c xConfiguration SIP Registration Call Remove: No
*c xConfiguration SIP Session Refresh Value: 1800
*c xConfiguration SIP Session Refresh Minimum: 500
*c xConfiguration SIP UDP Mode: Off
*c xConfiguration SIP UDP Port: 5060
*c xConfiguration SIP TCP Mode: On
*c xConfiguration SIP TCP Port: 5060
*c xConfiguration SIP TCP Outbound Port Start: 25000
*c xConfiguration SIP TCP Outbound Port End: 29999
*c xConfiguration SIP TLS Mode: On
*c xConfiguration SIP TLS Port: 5061
*c xConfiguration SIP TLS Certificate Revocation Checking Mode: Off
*c xConfiguration SIP TLS Certificate Revocation Checking OCSP Mode: On
*c xConfiguration SIP TLS Certificate Revocation Checking CRL Mode: On
*c xConfiguration SIP TLS Certificate Revocation Checking CRL Network Fetch
Mode: On
*c xConfiguration SIP TLS Certificate Revocation Checking Source Inaccessibility
Behavior: Fail
*c xConfiguration SIP Require UDP BFCP Mode: On
*c xConfiguration SIP Require Duo Video Mode: On
*c xConfiguration SIP Authentication Retry Limit: 3
*c xConfiguration SIP Authentication NTLM Mode: Auto
*c xConfiguration SIP Authentication NTLM SA Lifetime: 28800
*c xConfiguration SIP Authentication NTLM SA Limit: 10000
*c xConfiguration SIP Authentication Digest Nonce ExpireDelta: 300
*c xConfiguration SIP Authentication Digest Nonce Maximum Use Count: 128
*c xConfiguration SIP Authentication Digest Nonce Limit: 10000
*c xConfiguration SIP Authentication Digest Nonce Length: 60
*c xConfiguration SIP GRUU Mode: On
*c xConfiguration SIP MediaRouting ICE Mode: Off
*c xConfiguration Interworking Mode: RegisteredOnly
*c xConfiguration Interworking Encryption Mode: Auto
*c xConfiguration Interworking Encryption Replay Protection Mode: Off
*c xConfiguration Interworking BFCP Compatibility Mode: Auto
*c xConfiguration Interworking Require Invite Header Mode: On
*c xConfiguration Traversal Media Port Start: 50000
*c xConfiguration Traversal Media Port End: 52399
*c xConfiguration Authentication UserName: ""
*c xConfiguration Authentication Password: "{cipher}XXXXXXXXXXXXXXXXXXXXXX"
*c xConfiguration Authentication LDAP AliasOrigin: LDAP
*c xConfiguration Authentication ADS ADDomain: ""
*c xConfiguration Authentication ADS Workgroup: ""
*c xConfiguration Authentication ADS MachinePassword Refresh: On
*c xConfiguration Authentication ADS SPNEGO: Enabled
*c xConfiguration Authentication ADS SecureChannel: Auto
*c xConfiguration Authentication ADS Encryption: TLS
*c xConfiguration Authentication ADS Mode: Off
*c xConfiguration Authentication ADS Clockskew: 300
*c xConfiguration Zones Policy Mode: SearchRules
*c xConfiguration Zones Policy SearchRules Rule 1 Name: "Local zone ? no domain"
*c xConfiguration Zones Policy SearchRules Rule 1 Description: "Search local
zone for H.323 devices (strip domain)"
*c xConfiguration Zones Policy SearchRules Rule 1 Priority: 48
*c xConfiguration Zones Policy SearchRules Rule 1 Protocol: Any
*c xConfiguration Zones Policy SearchRules Rule 1 Source Mode: Any
*c xConfiguration Zones Policy SearchRules Rule 1 Authentication: No
*c xConfiguration Zones Policy SearchRules Rule 1 Mode: AliasPatternMatch
*c xConfiguration Zones Policy SearchRules Rule 1 Pattern Type: Regex
*c xConfiguration Zones Policy SearchRules Rule 1 Pattern String: "(.+)
@######.local.*"
*c xConfiguration Zones Policy SearchRules Rule 1 Pattern Behavior: Replace
*c xConfiguration Zones Policy SearchRules Rule 1 Pattern Replace: "\1"
*c xConfiguration Zones Policy SearchRules Rule 1 Progress: Continue
*c xConfiguration Zones Policy SearchRules Rule 1 Target Type: Zone
*c xConfiguration Zones Policy SearchRules Rule 1 Target Name: "LocalZone"
*c xConfiguration Zones Policy SearchRules Rule 1 State: Enabled
*c xConfiguration Zones Policy SearchRules Rule 2 Name: "Local zone ? full URI"
*c xConfiguration Zones Policy SearchRules Rule 2 Description: "Search local
zone for SIP and H.323 devices with a domain"
*c xConfiguration Zones Policy SearchRules Rule 2 Priority: 51
*c xConfiguration Zones Policy SearchRules Rule 2 Protocol: Any
*c xConfiguration Zones Policy SearchRules Rule 2 Source Mode: Any
*c xConfiguration Zones Policy SearchRules Rule 2 Authentication: No
*c xConfiguration Zones Policy SearchRules Rule 2 Mode: AliasPatternMatch
*c xConfiguration Zones Policy SearchRules Rule 2 Pattern Type: Regex
*c xConfiguration Zones Policy SearchRules Rule 2 Pattern String: "(.+)
@######.local.*"
*c xConfiguration Zones Policy SearchRules Rule 2 Pattern Behavior: Leave
*c xConfiguration Zones Policy SearchRules Rule 2 Pattern Replace: ""
*c xConfiguration Zones Policy SearchRules Rule 2 Progress: Continue
*c xConfiguration Zones Policy SearchRules Rule 2 Target Type: Zone
*c xConfiguration Zones Policy SearchRules Rule 2 Target Name: "LocalZone"
*c xConfiguration Zones Policy SearchRules Rule 2 State: Enabled
*c xConfiguration Zones Policy SearchRules Rule 3 Name: "Traversal zone search rule"
*c xConfiguration Zones Policy SearchRules Rule 3 Description: "Search traversal
zone (Cisco VCS Expressway)"
*c xConfiguration Zones Policy SearchRules Rule 3 Priority: 100
*c xConfiguration Zones Policy SearchRules Rule 3 Protocol: Any
*c xConfiguration Zones Policy SearchRules Rule 3 Source Mode: Any
*c xConfiguration Zones Policy SearchRules Rule 3 Authentication: No
*c xConfiguration Zones Policy SearchRules Rule 3 Mode: AnyAlias
*c xConfiguration Zones Policy SearchRules Rule 3 Progress: Continue
*c xConfiguration Zones Policy SearchRules Rule 3 Target Type: Zone
*c xConfiguration Zones Policy SearchRules Rule 3 Target Name: "TraversalZone"
*c xConfiguration Zones Policy SearchRules Rule 3 State: Enabled
*c xConfiguration Zones Policy SearchRules Rule 4 Name: "External IP address
search rule"
*c xConfiguration Zones Policy SearchRules Rule 4 Description: "Route external
IP address"
*c xConfiguration Zones Policy SearchRules Rule 4 Priority: 100
*c xConfiguration Zones Policy SearchRules Rule 4 Protocol: Any
*c xConfiguration Zones Policy SearchRules Rule 4 Source Mode: Any
*c xConfiguration Zones Policy SearchRules Rule 4 Authentication: No
*c xConfiguration Zones Policy SearchRules Rule 4 Mode: AnyIPAddress
*c xConfiguration Zones Policy SearchRules Rule 4 Progress: Continue
*c xConfiguration Zones Policy SearchRules Rule 4 Target Type: Zone
*c xConfiguration Zones Policy SearchRules Rule 4 Target Name: "TraversalZone"
*c xConfiguration Zones Policy SearchRules Rule 4 State: Enabled
*c xConfiguration Zones Policy SearchRules Rule 5 Name: "LocalZoneMatch"
*c xConfiguration Zones Policy SearchRules Rule 5 Description: "Default rule:
queries the Local Zone for any alias"
*c xConfiguration Zones Policy SearchRules Rule 5 Priority: 50
*c xConfiguration Zones Policy SearchRules Rule 5 Protocol: Any
*c xConfiguration Zones Policy SearchRules Rule 5 Source Mode: Any
*c xConfiguration Zones Policy SearchRules Rule 5 Authentication: No
*c xConfiguration Zones Policy SearchRules Rule 5 Mode: AnyAlias
*c xConfiguration Zones Policy SearchRules Rule 5 Progress: Continue
*c xConfiguration Zones Policy SearchRules Rule 5 Target Type: Zone
*c xConfiguration Zones Policy SearchRules Rule 5 Target Name: "LocalZone"
*c xConfiguration Zones Policy SearchRules Rule 5 State: Enabled
*c xConfiguration Zones DefaultZone Authentication Mode: DoNotCheckCredentials
*c xConfiguration Zones DefaultZone SIP Record Route Address Type: IP
*c xConfiguration Zones DefaultZone SIP TLS Verify Mode: Off
*c xConfiguration Zones DefaultZone SIP Media Encryption Mode: Auto
*c xConfiguration Zones LocalZone DefaultSubZone SIP Media Encryption Mode: Auto
*c xConfiguration Zones LocalZone DefaultSubZone Authentication Mode:
DoNotCheckCredentials
*c xConfiguration Zones LocalZone DefaultSubZone Registrations: Allow
*c xConfiguration Zones LocalZone DefaultSubZone Bandwidth Total Mode: Unlimited
*c xConfiguration Zones LocalZone DefaultSubZone Bandwidth PerCall Inter Mode:
Unlimited
*c xConfiguration Zones LocalZone DefaultSubZone Bandwidth PerCall Intra Mode:
Unlimited
*c xConfiguration Zones LocalZone TraversalSubZone Bandwidth Total Mode: Unlimited
*c xConfiguration Zones LocalZone TraversalSubZone Bandwidth PerCall Mode:
Unlimited
*c xConfiguration Zones LocalZone SIP Record Route Address Type: IP
*c xConfiguration Zones Zone 1 Name: "TraversalZone"
*c xConfiguration Zones Zone 1 HopCount: 15
*c xConfiguration Zones Zone 1 H323 Mode: On
*c xConfiguration Zones Zone 1 SIP Mode: On
*c xConfiguration Zones Zone 1 Type: TraversalClient
*c xConfiguration Zones Zone 1 TraversalClient Authentication Mode: DoNot
CheckCredentials
*c xConfiguration Zones Zone 1 TraversalClient Authentication UserName:
"######auth"
*c xConfiguration Zones Zone 1 TraversalClient Authentication Password:
"{cipher}XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX"
*c xConfiguration Zones Zone 1 TraversalClient Registrations: Allow
*c xConfiguration Zones Zone 1 TraversalClient H323 Protocol: Assent
*c xConfiguration Zones Zone 1 TraversalClient H323 Port: 6001
*c xConfiguration Zones Zone 1 TraversalClient SIP Protocol: Assent
*c xConfiguration Zones Zone 1 TraversalClient SIP Port: 7001
*c xConfiguration Zones Zone 1 TraversalClient SIP Transport: TLS
*c xConfiguration Zones Zone 1 TraversalClient SIP TLS Verify Mode: Off
*c xConfiguration Zones Zone 1 TraversalClient SIP Poison Mode: Off
*c xConfiguration Zones Zone 1 TraversalClient SIP Media Encryption Mode: Auto
*c xConfiguration Zones Zone 1 TraversalClient RetryInterval: 120
*c xConfiguration Zones Zone 1 TraversalClient Peer 1 Address: "10.10.10.102"
*c xConfiguration Zones Zone 1 TraversalClient Peer 2 Address: ""
*c xConfiguration Zones Zone 1 TraversalClient Peer 3 Address: ""
*c xConfiguration Zones Zone 1 TraversalClient Peer 4 Address: ""
*c xConfiguration Zones Zone 1 TraversalClient Peer 5 Address: ""
*c xConfiguration Zones Zone 1 TraversalClient Peer 6 Address: ""
*c xConfiguration Bandwidth Default: 384
*c xConfiguration Bandwidth Downspeed PerCall Mode: On
*c xConfiguration Bandwidth Downspeed Total Mode: On
*c xConfiguration Bandwidth Link 1 Name: "DefaultSZtoTraversalSZ"
*c xConfiguration Bandwidth Link 1 Node1 Name: "DefaultSubZone"
*c xConfiguration Bandwidth Link 1 Node2 Name: "TraversalSubZone"
*c xConfiguration Bandwidth Link 1 Pipe1 Name: ""
*c xConfiguration Bandwidth Link 1 Pipe2 Name: ""
*c xConfiguration Bandwidth Link 2 Name: "DefaultSZtoDefaultZ"
*c xConfiguration Bandwidth Link 2 Node1 Name: "DefaultSubZone"
*c xConfiguration Bandwidth Link 2 Node2 Name: "DefaultZone"
*c xConfiguration Bandwidth Link 2 Pipe1 Name: ""
*c xConfiguration Bandwidth Link 2 Pipe2 Name: ""
*c xConfiguration Bandwidth Link 3 Name: "DefaultSZtoClusterSZ"
*c xConfiguration Bandwidth Link 3 Node1 Name: "DefaultSubZone"
*c xConfiguration Bandwidth Link 3 Node2 Name: "ClusterSubZone"
*c xConfiguration Bandwidth Link 3 Pipe1 Name: ""
*c xConfiguration Bandwidth Link 3 Pipe2 Name: ""
*c xConfiguration Bandwidth Link 4 Name: "TraversalSZtoDefaultZ"
*c xConfiguration Bandwidth Link 4 Node1 Name: "TraversalSubZone"
*c xConfiguration Bandwidth Link 4 Node2 Name: "DefaultZone"
*c xConfiguration Bandwidth Link 4 Pipe1 Name: ""
*c xConfiguration Bandwidth Link 4 Pipe2 Name: ""
*c xConfiguration Bandwidth Link 5 Name: "Zone001ToTraversalSZ"
*c xConfiguration Bandwidth Link 5 Node1 Name: "TraversalZone"
*c xConfiguration Bandwidth Link 5 Node2 Name: "TraversalSubZone"
*c xConfiguration Bandwidth Link 5 Pipe1 Name: ""
*c xConfiguration Bandwidth Link 5 Pipe2 Name: ""
*c xConfiguration Policy AdministratorPolicy Mode: Off
*c xConfiguration Policy AdministratorPolicy Service Protocol: HTTP
*c xConfiguration Policy AdministratorPolicy Service TLS Verify Mode: On
*c xConfiguration Policy AdministratorPolicy Service TLS CRLCheck Mode: Off
*c xConfiguration Policy AdministratorPolicy Service Server 1 Address: ""
*c xConfiguration Policy AdministratorPolicy Service Server 2 Address: ""
*c xConfiguration Policy AdministratorPolicy Service Server 3 Address: ""
*c xConfiguration Policy AdministratorPolicy Service Path: ""
*c xConfiguration Policy AdministratorPolicy Service Status Path: "status"
*c xConfiguration Policy AdministratorPolicy Service UserName: ""
*c xConfiguration Policy AdministratorPolicy Service Password: "{cipher}
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX"
*c xConfiguration Policy AdministratorPolicy Service DefaultCPL: "<reject
status='504' reason='Admin Policy Unavailable'/>"
*c xConfiguration Policy FindMe Mode: Off
*c xConfiguration Policy FindMe CallerId: IncomingID
*c xConfiguration Policy FindMe UserDeviceRestriction: Off
*c xConfiguration Applications ConferenceFactory Mode: Off
*c xConfiguration Applications ConferenceFactory Alias: ""
*c xConfiguration Applications ConferenceFactory Template: ""
*c xConfiguration Applications ConferenceFactory Range Start: 1
*c xConfiguration Applications ConferenceFactory Range End: 65535
*c xConfiguration Applications OCS Relay Mode: Off
*c xConfiguration Applications OCS Relay OCS Domain: ""
*c xConfiguration Applications OCS Relay OCS Routing Prefix: "ocs"
*c xConfiguration Applications Presence Server Mode: Off
*c xConfiguration Applications Presence Server Publication ExpireDelta: 1800
*c xConfiguration Applications Presence Server Subscription ExpireDelta: 3600
*c xConfiguration Applications Presence User Agent Mode: Off
*c xConfiguration Applications Presence User Agent ExpireDelta: 3600
*c xConfiguration Applications Presence User Agent RetryDelta: 1800
*c xConfiguration Applications Presence User Agent Presentity Idle Status: Online
*c xConfiguration ResourceUsage Warning Activation Level: 90
*c xConfiguration Services AdvancedMediaGateway Zone Name: ""
*c xConfiguration Services AdvancedMediaGateway Policy Mode: Off
OK
exit
Bye!
疑難排解
以下是您可能會遇到的三個最常見問題：
- 串列電纜使用不正確或故障。確保使用裝置隨附的電纜。
- 無法識別的字元顯示在控制檯螢幕上。這表示波特率設定不正確。波特率基於兩個的倍數，因此您可以根據需要將值加一倍或減半，直到找到正確的設定。在這種情況下，正確的設定應為115,200。
- 您無法連線到終端模擬軟體。除了佈線問題，此問題通常是由以下問題之一導致的：
- 您嘗試通過Telnet或SSH進行連線，使用串列連線時，必須將連線型別更改為串列。
- 您使用的COM埠不正確。要查詢您的PC使用基於USB的串列連線的COM埠，請導航到控制面板>裝置管理器，然後按一下埠。在此視窗中，您可以驗證分配給USB串列裝置的COM埠。
- 您沒有安裝串列裝置的驅動程式。如果是這種情況，您必須找到並安裝它們。
- 您嘗試通過Telnet或SSH進行連線，使用串列連線時，必須將連線型別更改為串列。
- 您無法通過SSH連線到裝置。除了佈線問題，此問題通常是由以下問題之一導致的：
- 您嘗試通過SSH連線，但由於網路連線問題而無法到達裝置。糾正網路連線問題。或者，可能沒有為裝置啟用SSH。通過Web/HTTP/HTTPS連線到裝置，並確保在Configuration>SystemConfiguration>Network Services下啟用了SSH訪問。
- 您沒有從裝置快取的Rivest-Shamir-Addleman(RSA)金鑰。通常，系統會提示您接受RSA金鑰。務必接受金鑰。
- 由於使用者名稱和密碼不正確，登入失敗。確保為裝置使用正確的使用者名稱和密碼。
- 您嘗試通過SSH連線，但由於網路連線問題而無法到達裝置。糾正網路連線問題。或者，可能沒有為裝置啟用SSH。通過Web/HTTP/HTTPS連線到裝置，並確保在Configuration>SystemConfiguration>Network Services下啟用了SSH訪問。
修訂記錄
| 修訂 | 發佈日期 | 意見 |
|---|---|---|
1.0 |
15-Dec-2014 |
初始版本 |
意見