配置Nexus 9000:Packet Tracer工具

简介

本文档介绍如何配置Cisco Nexus 9000 Packet Tracer实用程序。

先决条件

要求

Cisco 建议您具有以下主题的基础知识：

• Cisco Nexus 9000硬件架构

使用的组件

本文档中的信息基于以下软件和硬件版本：

• Cisco Nexus 9500
• 软件版本7.0(3)I2(2a)

本文档中的信息都是基于特定实验室环境中的设备编写的。本文档中使用的所有设备最初均采用原始（默认）配置。如果您的网络处于活动状态，请确保您了解所有命令的潜在影响。

背景信息

Packet Tracer是Nexus 9000上的内置实用程序，可用于跟踪数据包通过交换机的路径。可使用命令行调用该命令，并可将其配置为匹配IP地址和/或第4层属性。它不能用于匹配ARP流量。

此工具可确认流是否通过交换机。它还提供了跟踪流量统计数据的计数器，这对断断续续/完全丢包的情况非常有用。

使用案例情景

• 仅适用于IPv4流（不支持IPv6和非IP）
• 此工具不显示wireshark显示的数据包内部详细信息。
• 间歇性丢包：Ping或其他任何实用程序都可能提供数据包丢失的确切症状
• 完全丢包

支持的硬件

仅支持带有Broadcom Trident II asic的线卡/交换矩阵模块或TOR。列表如下：

• N9K-C9372TX
• N9K-C9372PX
• N9K-C9332PQ
• N9K-C9396TX
• N9K-C9396PX
• N9K-C93128TX
• N9K-C9336PQ
• N9K-X9564PX
• N9K-X9564TX
• N9K-X9636PQ

不支持的硬件

• N9K-C93180YC-EX
• N9K-X9732C-EX
• N9K-C9232C
• N9k-C9272Q
• N9k-C92160YC

如何使用Packet Tracer

配置

Packet-tracer命令是EXEC级别的命令。

N9K-9508#test packet-tracer src_ip <src_ip> dst_ip <dst_ip> <==== provide your src and dst ip 
N9K-9508#test packet-tracer start <==== Start packet tracer
N9K-9508#test packet-tracer stop <==== Stop packet tracer
N9K-9508#test packet-tracer show <==== Check for packet matches

上述命令对存在于线卡或交换矩阵模块上的每个Broadcom Trident II Asic上的触发器进行编程。当具有匹配属性的流经过这些模块时，它显示计数器被命中，从而帮助识别交换机内的路径(入口模块 — >交换矩阵模块之一---->出口模块)。

计数器可用于关联丢包。

背景信息

交换矩阵模块互连I/O模块插槽。所有交换矩阵模块都处于活动状态并传输流量。每个交换矩阵模块两个Broadcom Trident II ASIC(T2)实例。

问题

PACL（端口访问列表）用于查看特定物理接口是否收到我们感兴趣的流量。但是，在Nexus平台上，某些线卡没有为PACL刻制TCAM。TCAM雕刻需要重新加载模块。在这些情况下，使用Packet Tracer匹配感兴趣的流量。您还可以跟踪通往交换矩阵端口和通往出口模块的数据包。因此，Packet Tracer可以让您更加深入地了解流量在交换机中的转发方式。

Packet Tracer使用为SPAN划分的TCAM条目。

解决方案

NS — 北星ASIC
T2 - Trident II ASIC
NFE — 网络转发引擎
ALE - ACI枝叶引擎

有关Nexus 9000交换机架构的详细信息，请参阅本白皮书。

使用案例：匹配入口模块上的流量、交换矩阵模块上的流量入口和出口模块上的T2 ASIC上的流量

下面是匹配感兴趣流量需要配置的基本步骤：

switch#test packet-tracer {<src-ip>|<dst-ip>|<src-l4-port>|<dst-l4-port>} [<protocol>] [detail-fp|detail-hg]

以下是您需要的配置：

switch#test packet-tracer src_ip <src_ip> dst_ip <dst_ip> protocol <>   <==== provide your src and dst ip and protocol (protocol option 1 is for icmp) 
switch#test packet-tracer start                                          <==== Start packet tracer
switch#test packet-tracer show    <==== Check for packet match statistics

您无需将其应用于任何特定接口。这些配置在T2 ASIC的所有实例上的所有LC/FM上安装过滤器ACL。
它显示流量进入的模块上的数据包计数。这与我们在模块（线卡和交换矩阵）上传入的感兴趣流量相匹配。

以下是配置示例：

N9K-9508# test packet-tracer src-ip 10.1.1.1 dst-ip 10.2.2.1 protocol 1 <=== Protocol 1 matches ICMP traffic
N9K-9508# test packet-tracer start

 以下是如何解释“test packet-tracer show”输出：

N9K-9508# test packet-tracer show
Packet-tracer stats
---------------------
Module 1:                                           <=== Slot #. Same output will be displayed for other Linecards's and Fabric modules.
Filter 1 installed: src-ip 10.1.1.1 dst-ip 10.2.2.1 <==== Our filter #1
ASIC instance 0:                                    <==== Trident ASIC instance #0
Entry 0: id = 7425, count = 0, active, fp,          <==== pakcet match count on front panel port. it could be any port 
Entry 1: id = 7426, count = 0, active, hg,          <==== packet match count from fabric module to T2 ASIC on the linecard
ASIC instance 1:
Entry 0: id = 7425, count = 0, active, fp,
Entry 1: id = 7426, count = 0, active, hg,
Filter 2 uninstalled:
Filter 3 uninstalled:
Filter 4 uninstalled:
Filter 5 uninstalled:

 配置示例:

 配置Packet Tracer:

N9K-9508# test packet-tracer src-ip 10.1.1.1 dst-ip 10.2.2.1 protocol 1 <==== Filter to match echo traffic. Protocol 1 to match icmp traffic
N9K-9508# test packet-tracer src-ip 10.2.2.1 dst-ip 10.1.1.1 protocol 1 <=== Filter to match echo reply traffic 
N9K-9508# test packet-tracer start                                      <==== Start packet tracer
N9K-9508# test packet-tracer show non-zero                              <==== Command to see packet statistics
Packet-tracer stats
---------------------
Module 1:
Filter 1 installed: src-ip 10.1.1.1 dst-ip 10.2.2.1
Filter 2 installed: src-ip 10.2.2.1 dst-ip 10.1.1.1
Filter 3 uninstalled:
Filter 4 uninstalled:
Filter 5 uninstalled:
Module 2:
Filter 1 installed: src-ip 10.1.1.1 dst-ip 10.2.2.1
Filter 2 installed: src-ip 10.2.2.1 dst-ip 10.1.1.1
Filter 3 uninstalled:
Filter 4 uninstalled:
Filter 5 uninstalled:
Module 22:
Filter 1 installed: src-ip 10.1.1.1 dst-ip 10.2.2.1
Filter 2 installed: src-ip 10.2.2.1 dst-ip 10.1.1.1
Filter 3 uninstalled:
Filter 4 uninstalled:
Filter 5 uninstalled:
Module 23:
Filter 1 installed: src-ip 10.1.1.1 dst-ip 10.2.2.1
Filter 2 installed: src-ip 10.2.2.1 dst-ip 10.1.1.1
Filter 3 uninstalled:
Filter 4 uninstalled:
Filter 5 uninstalled:
Module 24:
Filter 1 installed: src-ip 10.1.1.1 dst-ip 10.2.2.1
Filter 2 installed: src-ip 10.2.2.1 dst-ip 10.1.1.1
Filter 3 uninstalled:
Filter 4 uninstalled:
Filter 5 uninstalled:
Module 25:
Filter 1 installed: src-ip 10.1.1.1 dst-ip 10.2.2.1
Filter 2 installed: src-ip 10.2.2.1 dst-ip 10.1.1.1
Filter 3 uninstalled:
Filter 4 uninstalled:
Filter 5 uninstalled:

 测试：从模块1的SRC IP Connected Off到模块2的DST IP Connected Off运行ping:

Router# ping 10.1.1.1 source 10.2.2.1
PING 10.1.1.1 (10.1.1.1) from 10.2.2.1: 56 data bytes
64 bytes from 10.1.1.1: icmp_seq=0 ttl=253 time=0.77 ms
64 bytes from 10.1.1.1: icmp_seq=1 ttl=253 time=0.43 ms
64 bytes from 10.1.1.1: icmp_seq=2 ttl=253 time=0.408 ms
64 bytes from 10.1.1.1: icmp_seq=3 ttl=253 time=0.398 ms
64 bytes from 10.1.1.1: icmp_seq=4 ttl=253 time=0.383 ms
--- 10.1.1.1 ping statistics ---
5 packets transmitted, 5 packets received, 0.00% packet loss
round-trip min/avg/max = 0.383/0.477/0.77 ms

验证：检查Packet Tracer计数：

N9K-9508# test packet-tracer show non-zero <==== Command to see packet statistics 

 Packet-tracer stats
---------------------

Module 1:
Filter 1 installed: src-ip 10.1.1.1 dst-ip 10.2.2.1 protocol 1
ASIC instance 0:
Entry 0: id = 7425, count = 5, active, fp, <===== 5 Echo packets ingress on Module 1
Filter 2 installed: src-ip 10.2.2.1 dst-ip 10.1.1.1 protocol 1
Filter 3 uninstalled:
Filter 4 uninstalled:
Filter 5 uninstalled:

Module 2:
Filter 1 installed: src-ip 10.1.1.1 dst-ip 10.2.2.1 protocol 1
Filter 2 installed: src-ip 10.2.2.1 dst-ip 10.1.1.1 protocol 1
ASIC instance 0:
Entry 0: id = 7457, count = 5, active, fp, <===== 5 Echo reply packets ingress on Module 2
Filter 3 uninstalled:
Filter 4 uninstalled:
Filter 5 uninstalled:

Module 3:
Filter 1 installed: src-ip 10.1.1.1 dst-ip 10.2.2.1 protocol 1
Filter 2 installed: src-ip 10.2.2.1 dst-ip 10.1.1.1 protocol 1
Filter 3 uninstalled:
Filter 4 uninstalled:
Filter 5 uninstalled:

Module 4:
Filter 1 installed: src-ip 10.1.1.1 dst-ip 10.2.2.1 protocol 1
Filter 2 installed: src-ip 10.2.2.1 dst-ip 10.1.1.1 protocol 1
Filter 3 uninstalled:
Filter 4 uninstalled:
Filter 5 uninstalled:

Module 22:
Filter 1 installed: src-ip 10.1.1.1 dst-ip 10.2.2.1 protocol 1
ASIC instance 0:
Entry 0: id = 7425, count = 4, active, hg, <==== Fabric module 22 received 4 echo packets
Filter 2 installed: src-ip 10.2.2.1 dst-ip 10.1.1.1 protocol 1
Filter 3 uninstalled:
Filter 4 uninstalled:
Filter 5 uninstalled:

Module 23:
Filter 1 installed: src-ip 10.1.1.1 dst-ip 10.2.2.1 protocol 1
ASIC instance 0:
Entry 0: id = 7425, count = 1, active, hg, <==== Fabric module 23 received 1 echo packets 
Filter 2 installed: src-ip 10.2.2.1 dst-ip 10.1.1.1 protocol 1
ASIC instance 0:
Entry 0: id = 7425, count = 3, active, hg, <==== Fabric module 23 received 3 echo reply packets
Filter 3 uninstalled:
Filter 4 uninstalled:
Filter 5 uninstalled:

Module 24:
Filter 1 installed: src-ip 10.1.1.1 dst-ip 10.2.2.1 protocol 1
Filter 2 installed: src-ip 10.2.2.1 dst-ip 10.1.1.1 protocol 1
ASIC instance 0:
Entry 0: id = 7425, count = 2, active, hg, <==== Fabric module 23 received 2 echo reply packets
Filter 3 uninstalled:
Filter 4 uninstalled:
Filter 5 uninstalled:

Module 26:
Filter 1 installed: src-ip 10.1.1.1 dst-ip 10.2.2.1 protocol 1
Filter 2 installed: src-ip 10.2.2.1 dst-ip 10.1.1.1 protocol 1
Filter 3 uninstalled:
Filter 4 uninstalled:
Filter 5 uninstalled:
N9K-9508#

其他有用的命令:

test packet-tracer remove-all <===删除所有已配置的过滤器
test packet-tracer clear <filter #> <=== Clear counters for all filters or specified filter
test packet-tracer src_ip <.> dst_ip <> l4-dst-port <dst_port> | l4-src-port <src_port> | protocol <===根据L4 src_port、L4 dst_port或协议进行匹配。