当异常情况出现时,Cisco广域网交换卡和模块记录错误代码。交换机卡错误是由在底部的一个CD符号的交换机命令行界面(CLI)屏幕显示给用户。您能使用.dspcderrs命令显示错误列表。将根据访问级别显示错误。
本文档没有任何特定的要求。
本文档不限于特定的软件和硬件版本。
有关文档规则的详细信息,请参阅 Cisco 技术提示规则。
在此部分的此列表是IPX帧中继填充卡德(FRP)硬件错误的一参考被提交至strataCom级别。StrataCom级别错误只服务有意义。您也许不发现列出的所有错误。
============================================================================= ==== HARDWARE AND SOFTWARE error lists (hw_code.h) BY MGC (09-30-92) ==== ==== Present Revision: 2.0 ==== ==== Revision History: FDE/FEE + FTC BY CvH (05-25-94) ==== ==== Added Self-Test Failures BY CvH (06-22-94) ==== ==== Corrections BY CvH (08-18-94) ==== ==== Add non-ACP errors BY CvH (08-18-94) ==== ============================================================================= *** GENERIC FATAL ERRORS **** Hardware Error Message Format |Fcn Code (if due to a command, else 0) | |Error: 1 - download failure | | | 2 - power-up failure | | | 3 - selftest failure | | | 4 - memory test failure | | | 5 - internal boot failure | | | 6 - internal ACP failure | | | 7 - watchdog failure | | |Slot/Type (Type if MSB set): 99 (19) if FRP, A3 (23) if FTC | | | |Processor Number | | | | | 0B01029901 000000ii xxxxxxxx yyyyyyyy : Power-up Failure i = failure state 05h - novram checksum failed 06h - fifo loopback failed 07h - no state 0 msg from supv. (SRAM problem) 10h - fifo test failed 11h - no state 1 msg from supv. >= 12h - passed boot prom (missed handshake) x = failure address, y = data expected 0B01049901 xxxxxxxx yyyyyyyy zzzzzzzz: Memory Test Failure x = failure address, y = data expected, z = data received 0B01059901 000000ii : Internal Boot Failure i = failure mode 0 - waiting for HF flag change from DSP 1 - waiting for TXDE flag to go true from DSP 2 - waiting for RXDF flag to go true from DSP 3 - unable to initialize DSP 4 - unable to internal load DSP 5 - unable to program EEPROM 6 - bad message from CBUS controller 7 - 9th bit/msg format error from supv. 8 - no NMICLR in response to NMI to supv. 9 - timeout waiting for space in Admin fifo 0B00079901 : 8751 Watchdog Timeout *** FATAL HARDWARE ERRORS **** (The byte count will be 17) 0B00069901 FF 01 00 00 [sr:16][pc addr][vo:16] : acp_stop Error (@pc addr) 0B00069901 FF 01 00 01 [ pc addr ] [err addr ] : pSOS K_FATAL Error (@pc addr) error usually a pSOS code: 4B = max. num. cnfg. timers exceeded *** FATAL ADDRESS/BUS EXCEPTION ERRORS **** (The byte count will be 23) 0B00069901 FF 01 00 00 [sr:16][pc addr][vo:16][ssw:16][fault addr] *** NON-FATAL HARDWARE ERRORS **** (The byte count will be 13) 0B00069901 01 00 00 C0 [lcn ] : Expect psos message (test frame) 0B00069901 01 00 ii C1 00 00 00 00 : DIAGS test aborted in tm on; i = port 0B00069901 01 00 ii C3 [message ] : Loopback frm not received; i = port 0B00069901 01 00 ii C4 [hchannel ] : Loopback frm bad hch number; i = port 0B00069901 01 00 ii C5 [length ] : Loopback frm bad frame length; i = port 0B00069901 01 00 ii C6 [address ] : Loopback frm incorrect data; i = port 0B00069901 01 00 ii C7 [address ] : Loopback frm zero segment; i = port 0B00069901 01 00 ii C8 [testnum ] : Invalid test number (diags); i = port 0B00069901 01 00 00 C9 [bc type ] : Bad internal card type 0B00069901 01 00 ii C9 00 00 00 00 : DIAGS test aborted in tm off; i = port 0B00069901 01 01 00 80 [response ] : Bad SLOT ID response (startup) 0B00069901 01 01 00 90 00 00 00 00 : Bad watch dog timer event rcvd (cmd_task) 0B00069901 01 01 D0 00 [status ] : FPTX HP failure status during dnld 0B00069901 01 01 D0 01 [status ] : FPTX watchdog HP failure status 0B00069901 01 01 D0 02 [status ] : FPTX activate HP error status 0B00069901 01 01 D0 03 [status ] : FPTX deactivate HP error status 0B00069901 01 01 D0 04 [status ] : FPTX write command HP error status 0B00069901 01 01 D0 05 [status ] : FPTX read command HP error status 0B00069901 01 01 D0 06 [status ] : FPTX self test HP error status 0B00069901 01 01 D0 07 [status ] : FPTX activate: HP status bad 0B00069901 01 01 D0 08 [status ] : FPTX purge: HP status bad 0B00069901 01 01 D0 09 [status ] : FPTX purge all: HP status bad 0B00069901 01 01 D0 0A [status ] : FPTX suspend: HP status bad 0B00069901 01 01 D0 0B [status ] : FPTX resume: HP status bad 0B00069901 01 01 D1 00 [status ] : FPRX HP failure status during dnld 0B00069901 01 01 D1 01 [status ] : FPRX watchdog HP failure status 0B00069901 01 01 D1 02 [status ] : FPRX activate HP error status 0B00069901 01 01 D1 03 [status ] : FPRX deactivate HP error status 0B00069901 01 01 D1 04 [status ] : FPRX write command HP error status 0B00069901 01 01 D1 05 [status ] : FPRX read command HP error status 0B00069901 01 01 D1 06 [status ] : FPRX self test HP error status 0B00069901 01 01 D1 07 [status ] : FPRX cnfig MC HP status 0B00069901 01 01 D1 08 [status ] : FPRX stats bad HP status [index ] : STATS invalid stats buffer index 0B00069901 01 01 D1 09 [status ] : FPRX LCA boot response bad HP status 0B00069901 01 01 D1 0A [status ] : FPRX suspend cnfig MC HP status 0B00069901 01 01 D1 0B [status ] : FPRX resume cnfig MC HP status 0B00069901 01 01 D2 00 [status ] : DMA HP failure status during dnld 0B00069901 01 01 D2 01 [status ] : DMA watchdog HP failure status 0B00069901 01 01 D2 02 [status ] : DMA activate HP error status 0B00069901 01 01 D2 03 [status ] : DMA deactivate HP error status 0B00069901 01 01 D2 04 [status ] : DMA write command HP error status 0B00069901 01 01 D2 05 [status ] : DMA read command HP error status 0B00069901 01 01 D2 06 [status ] : DMA self test HP error status 0B00069901 01 01 D2 07 [hch/stat ] : DMA HP msg failed @ enable channel 0B00069901 01 01 D2 08 [hch/stat ] : DMA HP msg failed @ disable channel 0B00069901 01 01 D2 0A [status ] : DMA HP msg failed @ inc hp counter 0B00069901 01 01 D2 0B [status ] : DMA HP msg failed @ reset hp counter 0B00069901 01 01 D2 0C [status ] : DMA HP msg failed @ resume receive 0B00069901 01 01 D2 0D [status ] : DMA HP msg failed @ halt receive 0B00069901 01 01 D2 0E [ts/stat ] : DMA HP msg failed @ idle code 0B00069901 01 01 D2 17 [code ] : DMA enable channel msg code incorrect 0B00069901 01 01 D2 18 [code ] : DMA disable channel msg code incorrect 0B00069901 01 01 D2 28 [length ] : DMA disable channel msg len. incorrect 0B00069901 01 02 00 8A [buf index] : FIFO cmd read too long/not end bit set 0B00069901 01 02 00 8C [msg index] : FIFO cmd too long to write out 0B00069901 01 02 00 8D 00 00 00 00 : Exceeded FIFO test wait time 0B00069901 01 02 00 8E 00 00 00 00 : VC Table corrupted ( 256 lcns) 0B00069901 01 02 00 8F 00 00 00 00 : Complex GW con received OAM packet 0B00069901 01 02 00 91 [Tmr 1 Cnt] : CIO Timer 1 Errors 0B00069901 01 02 00 92 [Tmr 2 Cnt] : CIO Timer 2 Errors 0B00069901 01 02 00 93 [Tmr 3 Cnt] : CIO Timer 3 Errors 0B00069901 01 02 00 94 [Prt A Cnt] : CIO Port A Errors 0B00069901 01 02 00 95 [Prt B Cnt] : CIO Port B Errors 0B00069901 01 02 ii B0 00 00 00 00 : PRT_CTRL DxE setup failure; i = port 0B00069901 01 02 ii B1 [baudindex] : PRT_CTRL invalid baud rate; i = port 0B00069901 01 02 ii B2 [clkselect] : PRT_CTRL invalid clk select; i = port 0B00069901 01 02 ii B3 [timer cnt] : PRT_CTRL invalid pit count; i = port 0B00069901 01 02 ii B4 00 00 00 00 : BRSAMPLE invalid cntr value; i = port 0B00069901 01 02 ii B5 00 00 00 00 : BRSAMPLE invalid timer value; i = port 0B00069901 01 02 ii B6 00 00 00 00 : BRSAMPLE zero elapsed time; i = port 0B00069901 01 02 ii B8 [eia lead ] : EIA_MON lead failure; i = port 0B00069901 01 02 00 F2 [checksum ] : Bad novram checksum 0B00069901 01 02 00 CA 00 00 00 ii : CAM_CTRL update_lcn_cam, inv. port = i 0B00069901 01 02 01 CA 00 00 00 ii : CAM_CTRL clear_lcn_cam, inv. port = i 0B00069901 01 02 02 CA 00 00 00 ii : CAM_CTRL cam_lcn_lookup, inv. port = i 0B00069901 D0 00 03 01 [data ] : FPTX watchdog failure data 0B00069901 D0 01 01 00 [length ] : FPTX bad rsp length after dnld (dsp_ctrl) 0B00069901 D0 01 01 01 [length ] : FPTX watchdog response incorrect length 0B00069901 D0 01 01 05 [length ] : FPTX read command incorrect length 0B00069901 D0 01 01 06 [length ] : FPTX self test incorrect length 0B00069901 D0 01 01 09 [length ] : FPTX purge all: incorrect length rtned 0B00069901 D0 01 01 DB 00 00 00 00 : FPTX bootstrap failed 0B00069901 D0 01 02 00 [code ] : FPTX bad code rsp after dnld (dsp_ctrl) 0B00069901 D0 01 02 01 [code ] : FPTX watchdog incorrect fcn. code rtned 0B00069901 D0 01 02 05 [code ] : FPTX read command incorrect msg code 0B00069901 D0 01 02 06 [code ] : FPTX self test incorrect msg code 0B00069901 D0 01 02 09 [code ] : FPTX purge all: incorrect code returned 0B00069901 D0 01 02 DB 00 00 00 00 : FPTX boot failed 0B00069901 D0 01 03 00 [data ] : FPTX bad data rsp after dnld (dsp_ctrl) 0B00069901 D0 01 03 01 [data ] : FPTX watchdog failure data 0B00069901 D0 01 03 06 [status ] : FPTX STSTS self-test error 0B00069901 D1 00 03 01 [data ] : FPRX watchdog failure data 0B00069901 D1 01 01 01 [length ] : FPRX watchdog response incorrect length 0B00069901 D1 01 01 00 [length ] : FPRX bad rsp length after dnld (dsp_ctrl) 0B00069901 D1 01 01 05 [length ] : FPRX read command incorrect length 0B00069901 D1 01 01 06 [length ] : FPRX self test incorrect length 0B00069901 D1 01 01 08 [length ] : FPRX stats response bad length 0B00069901 D1 01 01 09 [length ] : FPRX LCA boot response bad length 0B00069901 D1 01 01 DB 00 00 00 00 : FPRX bootstrap failed 0B00069901 D1 01 02 00 [code ] : FPRX bad code rsp after dnld (dsp_ctrl) 0B00069901 D1 01 02 01 [code ] : FPRX watchdog incorrect fcn code rtned 0B00069901 D1 01 02 05 [code ] : FPRX read command incorrect msg code 0B00069901 D1 01 02 06 [code ] : FPRX self test incorrect msg code 0B00069901 D1 01 02 08 [code ] : FPRX stats response bad code 0B00069901 D1 01 02 09 [code ] : FPRX LCA boot response bad code 0B00069901 D1 01 02 DB 00 00 00 00 : FPRX boot failed 0B00069901 D1 01 03 00 [data ] : FPRX bad data rsp after dnld (dsp_ctrl) 0B00069901 D1 01 03 01 [data ] : FPRX watchdog failure data 0B00069901 D1 01 03 06 [status ] : FPRX STSTS self-test error 0B00069901 D1 01 03 09 [data ] : FPRX LCA boot error response data <> 0 0B00069901 D2 00 03 01 [data ] : DMA watchdog failure data 0B00069901 D2 01 01 00 [length ] : DMA bad rsp length after dnld (dsp_ctrl) 0B00069901 D2 01 01 01 [length ] : DMA watchdog response incorrect length 0B00069901 D2 01 01 05 [length ] : DMA read command incorrect length 0B00069901 D2 01 01 06 [length ] : DMA self test incorrect length 0B00069901 D2 01 01 09 [msg len ] : DMA incorrect msg length 0B00069901 D2 01 01 DB 00 00 00 00 : DMA bootstrap failed 0B00069901 D2 01 02 00 [code ] : DMA bad code rsp after dnld (dsp_ctrl) 0B00069901 D2 01 02 01 [code ] : DMA watchdog incorrect fcn code rtned 0B00069901 D2 01 02 05 [code ] : DMA read command incorrect msg code 0B00069901 D2 01 02 06 [code ] : DMA self test incorrect msg code 0B00069901 D2 01 02 09 [msg code ] : DMA incorrect msg code 0B00069901 D2 01 02 DB 00 00 00 00 : DMA boot failed 0B00069901 D2 01 03 00 [data ] : DMA bad data rsp after dnld (dsp_ctrl) 0B00069901 D2 01 03 01 [data ] : DMA watchdog failure data 0B00069901 D2 01 03 06 [status ] : DMA STSTS self-test error 0B00069901 D2 01 03 09 [msg data ] : DMA incorrect msg 0B00069901 DB 02 01 00 [ISR ptr ] : DSP not ready with TRDY 0B00069901 DB 02 02 00 [ISR ptr ] : DSP not ready with TXDE for bootstrap 0B00069901 DB 02 03 00 [ISR ptr ] : DSP not ready with TRDY for bootstrap 0B00069901 DB 02 11 00 [ISR ptr ] : DSP not ready with TXDE for boot 0B00069901 DB 02 12 00 [ISR ptr ] : DSP not ready for boot dnld 0B00069901 DB 02 13 00 [ISR ptr ] : DSP not ready with TRDY for boot 0B00069901 DB 02 14 00 [ISR ptr ] : DSP not ready with TXDE for boot 0B00069901 DB 02 15 00 [ISR ptr ] : DSP not ready with TRDY for boot 0B00069901 DD 02 02 00 [ISR ptr ] : DSP has not completed previous command 0B00069901 DD 02 03 00 [CVR ptr ] : DSP did not respond to sent command 0B00069901 DD 02 04 00 [ISR ptr ] : DSP did not receive HP bytes 0B00069901 DD 02 05 ii [ISR ptr ] : DSP not ready to receive 0B00069901 DD 02 06 00 [ISR ptr ] : DSP did not ack command reception 0B00069901 DD 02 07 00 [CVR ptr ] : DSP not ready for "execute host" cmd 0B00069901 DD 02 08 00 [ISR ptr ] : DSP did not ack command completion 0B00069901 DD 02 09 00 [ISR ptr ] : DSP did not return HP command response 0B00069901 DD 02 0A 00 [CVR ptr ] : DSP not ready for slave read response 0B00069901 DD 02 0B ii [ISR ptr ] : DSP failed to return RXDF 0B00069901 DD 02 0C 00 [CVR ptr ] : DSP not ready for close output 0B00069901 F0 01 00 03 [llcb_ptr ] : FREE_FRM: Frame Buffer Overflow (> Max FB/Frm) 0B00069901 F1 01 00 03 [frm_ptr ] : FTX_RECY: Frame Buffer Overflow (> Max FB/Frm) 0B00069901 F1 01 00 05 00 00 00 00 : FTX_RECY: Spyder overrun 0B00069901 F1 01 00 06 00 00 00 00 : FTX_RECY: Spyder underrun 0B00069901 F1 01 00 07 [hpr_q_ptr] : FTX_PURG: Bad Hi-priority Q pointer 0B00069901 F1 01 00 08 [lpr_q_ptr] : FTX_PURG: Bad Lo-priority Q pointer 0B00069901 F1 01 00 09 [fim_q_ptr] : FIM_PURG: Bad Fim Q pointer 0B00069901 F1 01 00 0D [dma error] : FTX_RECY: Undefined TX DMA Error 0B00069901 F2 01 00 01 [fcb_tail ] : FRX_RECY: FCB Q overflow [Port only] 0B00069901 F2 01 00 03 [frm_ptr ] : FRX_RECY: Recycled too many frame bufs 0B00069901 F2 01 00 04 [prev_fptr] : FRX_RXFR: SOF rcvd B4 last frame's EOF [curr_fptr] : FRX_RXFR: (always comes in pairs) 0B00069901 F2 01 00 05 [error ] : FRX_RXFR: Unexpected DMA error code 0B00069901 F2 01 00 06 00 00 00 00 : FRX_RXFR: SPYDER UNDERRUN 0B00069901 F2 01 00 0A [pointer ] : FRX_RXFR: DMA interrupt Q Overrun 0B00069901 F2 01 00 0B [error ] : FRX_RXFR: Undefined RX DMA error 0B00069901 F2 01 00 0C [hyperch ] : FRX_RECY: FB in use underrun (count) 0B00069901 F2 01 00 0E [frm_ptr ] : FRX_IDLE: Zero FB Reported (FRX_DLOK/DLC0/PTLB) 0B00069901 F2 01 00 0F [hyperch ] : FRX_RXFR: Invalid DMA hyperchannel 0B00069901 F2 01 00 10 [pt_rx_ptr] : FRX_RXFR: Invalid DMA offset 0B00069901 F2 01 00 11 [frm_ptr ] : FRX_RXFR: Firmware Frame in Progress Error 0B00069901 F2 01 00 12 [frm_ptr ] : FRX_RXFR: Missing EOF Status 0B00069901 F2 01 00 13 [frm_ptr ] : FRX_RXFR: Sequence Error Status *** SOFTWARE ERRORS **** (The byte count will be 3) Guidelines for Error Codes: 0 - unknown function code 1 - illegal length 2 - illegal parameter 3 - unused 4 - illegal for card state 5 - illegal for channel state 6 - configuration error 7 - illegal for backcard state Error Code Module Error Reason ---------- -------- --------------------------------------- 02 xx 00 : COMMAND : Invalid command *** SPECIAL *** 02 xx 01 : COMMAND : Invalid message length *** SPECIAL *** 02 03 03 : CMD_STST : Bad self test number ( != 0 or 1) 02 03 04 : CMD_STST : FRIC not active 02 18 02 : CMD_MEM : Bad parameter (write_memory_cmd) 02 19 02 : CMD_MEM : Bad parameter ( read_memory_cmd) 02 1A 04 : CMD_MEM : Command not supported (memory_test_cmd) 02 1B 02 : CMD_MEM : Bad parameter (write_NOVRAM_cmd) 02 1C 02 : CMD_MEM : Bad parameter ( read_NOVRAM_cmd) 02 1D 02 : CMD_LED : Bad LED bitmap 02 1E 02 : CMD_DBUG : Command not supported (scope_loop_cmd) 02 1F 02 : CMD_DBUG : Invalid processor type (ascii_event_cmd) 02 20 04 : CMD_DNLD : Command not supported (transfer_begin_cmd) [PORT] 02 21 04 : CMD_DNLD : Command not supported (transfer_cmd) [PORT] 02 22 04 : CMD_DNLD : Command not supported (transfer_end_cmd) [PORT] 02 A0 02 : CMD_CFBC : Back card type mismatch 02 A0 03 : CMD_CFBC : Bad BC state parameter (BC_RESET) 02 A0 04 : CMD_CFBC : Bad BC state parameter (UNKNOWN) 02 A1 02 : CMD_BCST : Port not configured yet 02 A2 02 : CMD_ALM : Port not configured yet 02 A2 03 : CMD_ALM : Back card type mismatch 02 AB 04 : CMD_DCC : Bad time slot number ( >= MAX_E1_TIMESLOTS) 02 B0 02 : CMD_HCH : Bad hyperchannel number ( >= MAX_HCHANNELS) : CMD_PORT : Bad port ( >= Bd_Table.back_card_ports) 02 B0 04 : CMD_HCH : FRIC not active 02 B0 05 : CMD_HCH : Unallowd port reconfig (eg Bundled <= Unbundled) 02 B0 06 : CMD_HCH : Bad timeslot configuration 02 B0 07 : CMD_HCH : Timeslot number out of range 02 B0 08 : CMD_HCH : Timeslot already activated/deactivated 02 B0 xx : CMD_HCH : Bad back card type (xx = rcvd back card type) 02 B1 02 : CMD_PORT : Bad port ( >= Bd_Table.back_card_ports) 02 B2 02 : CMD_HCST : Bad hyperchannel number ( >= MAX_HCHANNELS) : CMD_PTST : Bad port ( >= Bd_Table.back_card_ports) 02 B3 02 : EIA_EVT : Bad port ( >= Bd_Table.back_card_ports) [PORT] (get_port_eia_status_cmd) 02 B4 02 : CARD_EVT : local bus param non-zero 02 B7 04 : CMD_ICA : FRIC not active 02 B8 02 : CMD_HCCG : Bad hyperchannel number ( >= MAX_HCHANNELS) : CMD_PTCG : Bad port ( >= Bd_Table.back_card_ports) 02 B8 04 : CMD_HCCG : FRIC not active 02 B9 02 : CMD_HCCG : Bad hyperchannel number ( >= MAX_HCHANNELS) : CMD_PTCG : Bad port ( >= Bd_Table.back_card_ports) 02 BF 02 : CMD_DIAG : Bad port ( >= Bd_Table.back_card_ports) [PORT] Bad test number ( != 1,2,3) [PORT] Bad test number to terminate 02 BF 03 : CMD_DIAG : Bad hyperchannel number ( >= MAX_HCHANNELS) 02 BF 04 : CMD_DIAG : Hyperchannel/FRIC not active 02 BF 05 : CMD_DIAG : Bad test number ( != 1, 2, or FF) [LINE] : CMD_DIAG : Port not active [PORT] 02 BF 06 : CMD_DIAG : Bad test number to terminate 02 BF 07 : CMD_DIAG : FRIC not active 02 C0 02 : CMD_VC : Bad hyperchannel number, DLCI, LCN : CMD_VC : Bad DLCI, port ( >= Bd_Table.back_card_ports) 02 C0 03 : CMD_VC : Hch/port number doesn't match database for active LC 02 C0 04 : CMD_VC : FRIC not active 02 C0 05 : CMD_VC : VC already active (used by multicast) [REMOVE] 02 C0 07 : CMD_VC : VC already active 02 C0 08 : CMD_VC : FastPAD not active 02 C1 02 : CMD_VC : Bad LCN [REMOVE] 02 C1 05 : CMD_VC : VC already active (used by multicast) [REMOVE] 02 C2 02 : CMD_VCST : Bad LCN [REMOVE] 02 C5 02 : CMD_MC : Command not supported 02 C6 02 : CMD_MC : Command not supported 02 C7 02 : CMD_RTD : Bad LCN [REMOVE] 02 C7 04 : CMD_RTD : FRIC not active 02 C8 02 : CMD_VCCG : Bad LCN [REMOVE], LCN not active 02 C8 03 : CMD_VCCG : LCN not active 02 C8 04 : CMD_VCCG : FRIC not active 02 C9 02 : CMD_VCCG : Bad LCN [REMOVE] 02 CC 02 : CMD_FPID : FRIC not active [PORT-FTC] 02 CC 03 : CMD_FPID : Bad port ( >= MAX_PORT) [PORT-FTC] 02 CC 04 : CMD_FPID : No match & no space found in Fp_Table [PORT-FTC] 02 CC 05 : CMD_FPID : Bundling on Fp inconsistent with Port [PORT-FTC] *** SELF-TEST RESPONSES **** (from STSTS) Code Meaning ---------- --------------------------------------- 03 00 : Done (Success) 03 80 : Abort 03 01 01 02 00 F0 00 00 00 00 : Fail - invalid FPTX self-test 03 01 01 02 00 F0 00 00 00 01 : Fail - invalid FPRX self-test 03 01 01 02 00 F0 00 00 00 02 : Fail - invalid DMA self-test 03 01 01 02 00 F2 xx xx yy yy : Fail - self_test_eeprom: x = calc. checksum, y = stored checksum @ 83FFFC 03 01 01 02 xx F3 yy yy yy yy : Fail - self_test_routing_table: x = test, y = routing table address 03 01 01 02 xx F4 yy yy yy yy : Fail - self_test_gram: x = test, y = GRAM address 03 01 01 02 00 F5 [data & 30] : Fail - self_test_power_monitor 03 01 D0 01 01 06 [ status ] : Fail - self_test_fptx 03 01 D1 01 01 06 [ status ] : Fail - self_test_fprx 03 01 D2 01 01 06 [ status ] : Fail - self_test_dma 03 01 D2 CA CA ii xx xx yy yy : Fail - self_test_cam [LINE] i = data pattern, x = lcn, y = CAM lcn