Trabalhos em rede do Cisco Unity Express com endereçamento DNS-baseado
Índice
Introdução
Este documento fornece uma configuração de exemplo para o perfil da Voz do correio de voz do Cisco Unity Express para trabalhos em rede do correio de Internet (VPIM) entre quatro locais. Dois dos locais são locais expressos do CallManager da Cisco de Cisco (CME), quando os outros dois estiverem sob o controle de um CallManager da Cisco central. Sua rede pode ser exclusivamente Cisco CME ou exclusivamente Cisco CallManager. Para modelar sua rede após esta configuração, refira os exemplos que combinam seu desenvolvimento pretendido. O cenário de configuração habilita a rede de correio de voz entre os quatro sites. A configuração tem as seguintes características:
- Rede combinada--Todos os sites podem enviar e receber mensagens de voz de todos os outros sites. Até 500 sites do Cisco Unity Express podem ser combinados em uma rede.
- Rede VPIM entre o endereçamento do Domain Name System (DNS) dos usos dos locais. Você pode igualmente usar o endereçamento de IP direto para estabelecer estas configurações, mas aquele não é mostrado neste exemplo de configuração.
- A rede define um quatro-dígito e o plano marcando do comprimento fixo do dez dígitos. Por exemplo, os Telefones IP no local 2 são atribuídos 2001 ou 2xx.yyy.2001 e 2002 ou 2xx.yyy.2002; Os Telefones IP no local 3 são são atribuídos 3001 ou 3xx.yyy.3001 e 3002 ou 3xx.yyy.3002. Refira a seção das “convenções de documento” na página 3 para mais detalhes sobre a numeração e o endereçamento usado nestes Telefones IP da publicação no mesmo local pode alcançar-se discando o quatro-dígito ou o número do dez dígitos. Os atendimentos entre Telefones IP em locais diferentes exigem discar o número 10-digit. Estas exigências não são limitações do Produtos ou a arquitetura, são aplicadas aqui para simplificar o exemplo da configuração de rede.
- A rede de correio de voz entre os locais é configurada para usar o endereçamento da extensão 10-digit.
- Os IDs de local de rede dos sites são iguais ao número do site. Por exemplo, o ID de localização do local 2's é 2, quando o ID de localização do local 3's for 3.
- Nenhuma conectividade de PSTN é mostrada nas configurações dos quatro sites, pois isso não é relevante para a configuração de rede do Cisco Unity Express. Escritórios reais em rede incluem esse componente adicional.
Pré-requisitos
As seções a seguir fornecem informações importantes para a compreensão desse exemplo de configuração. Consulte-as antes de prosseguir com o exemplo de configuração:
Requisitos
Não existem requisitos específicos para este documento.
Componentes Utilizados
As informações neste documento são baseadas nestas versões de software e hardware:
- No site 2, um roteador Cisco 3725 que executa o Cisco CME e o Cisco Unity Express
- No site 3, um roteador Cisco 2691 que executa o Cisco CME e o Cisco Unity Express
- No site 4, um roteador Cisco 3725 que executa a Cisco Secure Survivable Remote Site Telephony (SRST) e o Cisco Unity Express
- No site 6, um roteador Cisco 3725 que executa o Cisco SRST e o Cisco Unity Express
- Cisco IOS Release 12.3(11)T
- Cisco CME 3.2
- Cisco Unity Express 2.0
- Conjunto de recursos IP Voice Cisco IOS
Todos os sites são conectados por Ethernet à rede IP. Todos os sites têm dois telefones IP Cisco 7960. Para os sites Cisco CME (sites 2 e 3), os telefones IP e o plano de discagem estão sob o controle do Cisco CME. Para outros dois sites (sites 4 e 6), os telefones IP e o plano de discagem estão sob o controle de um Cisco CallManager central e os roteadores são configurados para operação SRST.
As informações apresentadas neste documento foram criadas a partir dos dispositivos em um ambiente de laboratório específico. Todos os dispositivos utilizados neste documento foram iniciados com uma configuração (padrão) inicial. Se a sua rede estiver ativa, certifique-se de que entende o impacto potencial de qualquer comando.
Produtos Relacionados
Essa configuração também pode ser usada com as seguintes versões de hardware e software:
- Cisco 2800 Series Routers
- Cisco 3800 Series Routers
- Para Cisco 2800 Series Routers, Cisco IOS Release 12.3(8)T4 ou releases posteriores. Para Cisco 3800 Series Routers, Cisco IOS Release 12.3(11)T e releases posteriores.
Convenções
Se for aplicável, este documento utiliza as convenções da Tabela 1.
Convenções de documento de exemplos de configuração do Cisco Unity Express da Tabela 1
| Convenção |
Descrição |
| texto em negrito |
O texto em negrito é usado para:
|
| < > (sinais de maior e menor) |
Os sinais de maior e menor são usados em torno dos parâmetros para os quais você fornece um valor. (Exemplo: Na janela do Prompt de comando, digite ping <IP address>.) |
| - (hífen) |
Os hífens separam as teclas que devem ser pressionadas simultaneamente. (Exemplo: Pressione Ctrl-Alt-Delete.) |
| > (suporte de ângulo adequado) |
O sinal de maior é usado para separar as seleções feitas:
|
| A letra a usada na faixa de endereços mais altos de um endereço IP formatado por V4. Exemplo: a .23.10.224 |
Representa uma rede ou um endereço de Internet público de Classe A. Usado somente para fins ilustrativos para impedir o uso de números públicos. |
| As letras x e y são usadas em números de telefone Exemplo: 2 xx. yyy .1234 |
Representa o código de área e o prefixo de um número de telefone. Usado somente para fins ilustrativos para impedir o uso de números públicos. |
O documento também usa as seguintes convenções gerais:
Nota: Significa que o leitor deve tomar nota. As notas contêm sugestões úteis ou referências a materiais não abordados no documento.
Cuidado: Significa que o leitor deve ter cuidado. Nessa situação, você pode fazer algo que pode resultar em danos ao equipamento ou perda de dados.
Para obter mais informações sobre convenções de documento, consulte as Convenções de dicas técnicas Cisco.
Configurar
Nesta seção, você encontrará informações para configurar os recursos descritos neste documento.
Nota: Para localizar informações adicionais sobre os comandos usados neste documento, utilize a Ferramenta Command Lookup (somente clientes registrados).
Diagrama de Rede
Este documento utiliza a instalação de rede mostrada no diagrama abaixo.
O local do site 2 usa um roteador Cisco 3725 com essas características:
- Acesso à rede IP através do endereço IP a.3.235.1
- Configuração do Cisco CME com 2 Telefones IP, com Ramais do 4-dígito 2001 e 2002
- Configuração do Cisco CME com 2 Telefones IP, com 10-digit Ramais 2xx.yyy.2001 e 2xx.yyy.2002
- Código de área 2xx PSTN
- NM-CUE
- Endereço IP a.3.235.128 do Cisco Unity Express
- ID 2 de local de rede
- O Domain Name do Cisco Unity Express DNS é ch2.cue.cisco.com
O local do site 3 usa um roteador Cisco 2691 com essas características:
- Acesso à rede IP através do endereço IP a.3.229.1
- Configuração do Cisco CME com 2 Telefones IP, com Ramais 3001 e 3002 do 4-dígito
- Configuração do Cisco CME com 2 Telefones IP, com 10-digit Ramais 3xx.yyy.3001 e 3xx.yyy.3002
- Código de área 3xx PSTN
- NM-CUE
- Endereço IP a.3.229.128 do Cisco Unity Express
- ID 3 de local de rede
- O Domain Name do Cisco Unity Express DNS é ch3.cue.cisco.com
O local do site 4 usa um roteador Cisco 3725 com essas características:
- Acesso à rede IP através do endereço a.3.231.10
- Configuração do CallManager/SRST de Cisco com 2 Telefones IP, com Ramais 4001 e 4002 do 4-dígito
- Configuração do Cisco CME com 2 Telefones IP, com 10-digit Ramais 4xx.yyy.4001 e 4xx.yyy.4002
- Código de área 4xx PSTN
- NM-CUE
- Endereço IP a.3.231.128 do Cisco Unity Express
- ID 4 de local de rede
- O Domain Name do Cisco Unity Express DNS é ch4.cue.cisco.com
O local do site 6 usa um roteador Cisco 3745 com essas características:
- Acesso à rede IP através do endereço IP a.3.245.1
- Configuração do CallManager/SRST de Cisco com 2 Telefones IP, com Ramais 6001 e 6002 do 4-dígito
- Configuração do Cisco CME com 2 Telefones IP, com 10-digit Ramais 6xx.yyy.6001 e 6xx.yyy.6002
- Código de área 6xx PSTN
- NM-CUE
- Endereço IP a.3.245.128 do Cisco Unity Express
- ID 6 de local de rede
- O Domain Name do Cisco Unity Express DNS é ch6.cue.cisco.com
Dicas de configuração
- Verifique se você pode executar ping entre os sites antes de fazer ligações.
- Verifique se você pode fazer ligações entre sites antes de tentar a rede do Cisco Unity Express.
- Verifique se você pode executar o comando ping entre os nós do Cisco Unity Express em cada site.
Configurações
Este documento usa a configuração mostrada abaixo:
- Configuração do site 2 (Cisco 3725/Roteador Cisco CME)
- Configuração do site 3 (Cisco 2691/Roteador Cisco CME)
- Configuração do site 4 (roteador Cisco 3725 SRST)
- Configuração do site 6 (roteador Cisco 3745 SRST)
Configuração do site 2 (Cisco 3725/Roteador Cisco CME)
As partes relevantes da configuração do roteador são mostradas abaixo:
cme-3725#
show running-config
Building configuration...
Current configuration : 8184 bytes
!
! Last configuration change at 11:01:46 PST Fri Nov 5 2004
! NVRAM config last updated at 08:29:05 PST Fri Nov 5 2004
!
version 12.3
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname cme-3725
!
boot-start-marker
boot system flash:c3725-ipvoice-mz.123-10.3.PI5
boot-end-marker
!
! Allow intersite H.323 calls to reach Cisco Unity Express
!
voice service voip
allow-connections h323 to sip
!
!
! IP address of the router
!
interface FastEthernet0/0
ip address a.3.235.1 255.255.0.0
duplex auto
speed auto
no cdp enable
!
interface FastEthernet0/1
ip address a.1.1.100 255.255.0.0
speed auto
half-duplex
no cdp enable
!
! IP address of Cisco Unity Express
!
interface Service-Engine1/0
ip unnumbered FastEthernet0/0
service-module ip address a.3.235.128 255.255.0.0
service-module ip default-gateway a.3.235.1
hold-queue 60 out
!
ip classless
ip route a.3.235.128 255.255.255.255 Service-Engine1/0
!
! Dial-peer to allow calls to forward from Cisco CME to Cisco Unity Express
!
dial-peer voice 2100 voip
destination-pattern 21..
session protocol sipv2
session target ipv4:a.3.235.128
dtmf-relay sip-notify
codec g711ulaw
no vad
!
dial-peer voice 2101 voip
description VM-AA-PSTN
translation-profile outgoing to_cue
destination-pattern 2xxyyy21..
session protocol sipv2
session target ipv4:a.3.235.128
dtmf-relay sip-notify
codec g711ulaw
no vad
!
! Dial-peers to direct intersite calls
!
dial-peer voice 3000 voip
destination-pattern 3xxyyy3...
session target ipv4:a.3.229.1
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
!
dial-peer voice 4000 voip
destination-pattern 4xxyyy4...
session target ipv4:a.3.231.5
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
!
dial-peer voice 6000 voip
destination-pattern 6xxyyy6...
session target ipv4:a.3.231.5
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
!
!
telephony-service
load 7960-7940 P00303020214
max-ephones 50
max-dn 120
ip source-address a.1.1.100 port 2000
time-format 24
date-format dd-mm-yy
auto assign 1 to 5
timeouts interdigit 20
timeouts ringing 120
system message CME-3725
create cnf-files version-stamp 7960 Sep 27 2004 12:31:02
dialplan-pattern 1 2xxyyy2... extension-length 4 no-reg
voicemail 2105
max-conferences 8
call-forward pattern .T
moh music-on-hold.au
web admin system name admin password cisco
web admin customer name custlogin password custpswd
dn-webedit
time-webedit
transfer-system full-consult
transfer-pattern 3...
transfer-pattern 2...
directory last-name-first
!
!
! Extension definitions
!
ephone-dn 1 dual-line
number 2001 secondary 2xxyyy2001
label Alice
description Alice Davidson
name Alice Davidson
call-forward max-length 4
call-forward busy 2105
call-forward noan 2105 timeout 10
!
!
ephone-dn 2 dual-line
number 2002 secondary 2xxyyy2002
label Aaron
description Aaron Wilkins
name Aaron Wilkins
call-forward max-length 8
call-forward busy 2105
call-forward noan 2105 timeout 10
!
!
! Dial-peers for MWI
!
ephone-dn 51
number 8000....
mwi on
!
!
ephone-dn 52
number 8001....
mwi off
!
!
!
! IP phone definitions
!
ephone 1
ephone-template 1
username "adavidson"
mac-address 0003.6BAA.D1F8
type 7960
button 1:1
!
!
!
ephone 2
ephone-template 1
username "awilkins"
mac-address 0003.6BAA.D362
type 7960
button 1:2
A configuração do Cisco Unity Express é mostrada abaixo:
cue-cme3725#
show running-config
Generating configuration:
clock timezone America/Los_Angeles
hostname cue-cme3725
ip domain-name localdomain
! Definition of the DNS server
ip name-server a.3.180.50
ntp server a.3.135.1
software download server url "ftp://127.0.0.1/ftp"
credentials hidden "6u/dKTN/hsEuSAEfw40XlF2eFHnZfyUTSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35jwAAAAA="
groupname Administrators create
groupname Broadcasters create
groupname Sales create
username adavidson create
username awilkins create
username acoley create
username awyant create
username amcdougal create
username admin create
groupname Sales phonenumberE164 "2xxyyy2050"
groupname Sales phonenumber "2050"
username adavidson phonenumberE164 "2xxyyy2001"
username awilkins phonenumberE164 "2xxyyy2002"
username acoley phonenumberE164 "2xxyyy2003"
username awyant phonenumberE164 "2xxyyy2004"
username amcdougal phonenumberE164 "2xxyyy2005"
username adavidson phonenumber "2001"
username awilkins phonenumber "2002"
username acoley phonenumber "2003"
username awyant phonenumber "2004"
username amcdougal phonenumber "2005"
groupname Administrators member admin
groupname Sales member acoley
groupname Sales member awilkins
groupname Administrators privilege superuser
groupname Administrators privilege ManagePrompts
backup server url "ftp://a.3.231.201/cme3725/"
credentials hidden "1SDP4vScNKcZiym6dHQHfnl4zvlbuAn9Sd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35jwAAAAA="
ccn application autoattendant
description "autoattendant"
enabled
maxsessions 8
script "aa.aef"
parameter "MaxRetry" "3"
parameter "operExtn" "0"
parameter "welcomePrompt" "AAWelcome.wav"
end application
ccn application ciscomwiapplication
description "ciscomwiapplication"
enabled
maxsessions 8
script "setmwi.aef"
parameter "strMWI_OFF_DN" "8001"
parameter "strMWI_ON_DN" "8000"
parameter "CallControlGroupID" "0"
end application
ccn application custom-aa
description "custom-aa"
enabled
maxsessions 8
script "s1_main-officehours.aef"
parameter "MainOperExt" "2001"
end application
ccn application promptmgmt
description "promptmgmt"
enabled
maxsessions 1
script "promptmgmt.aef"
end application
ccn application voicemail
description "voicemail"
enabled
maxsessions 8
script "voicebrowser.aef"
parameter "logoutUri" "http://localhost/voicemail/vxmlscripts/mbxLogout.jsp"
parameter "uri" "http://localhost/voicemail/vxmlscripts/login.vxml"
end application
ccn engine
end engine
ccn subsystem jtapi
ccm-manager address
end subsystem
ccn subsystem sip
gateway address "a.3.235.1"
end subsystem
ccn trigger sip phonenumber 2100
application "custom-aa"
enabled
locale "en_US"
maxsessions 8
end trigger
ccn trigger sip phonenumber 2102
application "autoattendant"
enabled
locale "en_US"
maxsessions 8
end trigger
ccn trigger sip phonenumber 2105
application "voicemail"
enabled
idletimeout 5000
locale "en_US"
maxsessions 8
end trigger
ccn trigger sip phonenumber 2106
application "promptmgmt"
enabled
idletimeout 5000
locale "en_US"
maxsessions 1
end trigger
! Definitions of the four networking sites
network location id 2
abbreviation "S2"
email domain ch2.cue.cisco.com
name "site2-cme-3725"
end location
network location id 3
abbreviation "S3"
email domain ch3.cue.cisco.com
name "site3-cme-2691"
end location
network location id 4
abbreviation "S4"
email domain ch4.cue.cisco.com
name "site4-ccm-3725"
end location
network location id 6
abbreviation "S6"
email domain ch6.cue.cisco.com
name "site6-ccm-3745"
end location
! Definition of this site’s location ID
network local location id 2
voicemail default expiration time 30
voicemail default language en_US
voicemail default mailboxsize 5520
voicemail recording time 900
voicemail default messagesize 60
voicemail operator telephone 2001
voicemail capacity time 6000
voicemail mailbox owner "Sales" size 5520
description "Sales mailbox"
zerooutnumber "2100"
end mailbox
voicemail mailbox owner "acoley" size 5520
description "acoley mailbox"
zerooutnumber "2100"
end mailbox
voicemail mailbox owner "adavidson" size 5520
description "adavidson mailbox"
zerooutnumber "2100"
end mailbox
voicemail mailbox owner "amcdougal" size 5520
description "amcdougal mailbox"
zerooutnumber "2100"
end mailbox
voicemail mailbox owner "awilkins" size 5520
description "awilkins mailbox"
zerooutnumber "2100"
end mailbox
voicemail mailbox owner "awyant" size 5520
description "awyant mailbox"
zerooutnumber "2100"
end mailbox
Configuração do site 3 (Cisco 2691/Roteador Cisco CME)
As partes relevantes da configuração do roteador são mostradas abaixo:
cme-2691#
show running-config
Building configuration...
Current configuration : 4868 bytes
!
! Last configuration change at 07:35:10 PST Fri Oct 22 2004
! NVRAM config last updated at 12:07:37 PST Fri Oct 22 2004
!
version 12.3
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname cme-2691
!
boot-start-marker
boot system flash:c2691-ipvoice-mz.123-10.3.PI5
boot-end-marker
!
! Allow intersite H.323 calls to reach Cisco Unity Express
!
voice service voip
allow-connections h323 to sip
!
! IP address of the router
!
interface FastEthernet0/0
ip address a.3.229.1 255.255.0.0
no ip mroute-cache
load-interval 30
duplex auto
speed auto
!
interface FastEthernet0/1
ip address a.10.1.100 255.255.0.0
no ip mroute-cache
duplex auto
speed auto
!
! IP address of Cisco Unity Express
!
interface Service-Engine1/0
ip unnumbered FastEthernet0/0
service-module ip address a.3.229.128 255.255.0.0
service-module ip default-gateway a.3.229.1
!
ip classless
ip route a.3.229.128 255.255.255.255 Service-Engine1/0
!
ip http server
ip http path flash:
!
! Dial-peer to allow calls to forward from Cisco CME to Cisco Unity Express
!
dial-peer voice 3100 voip
description VM-AA
destination-pattern 31..
session protocol sipv2
session target ipv4:a.3.229.128
dtmf-relay sip-notify
codec g711ulaw
no vad
¡
dial-peer voice 3101 voip
description VM-AA-PSTN
translation-profile outgoing to_cue
destination-pattern 3xxyyy31..
session protocol sipv2
session target ipv4:a.3.229.128
dtmf-relay sip-notify
codec g711ulaw
no vad
!
! Dial-peers to direct intersite calls
!
!
dial-peer voice 2001 voip
destination-pattern 2xxyyy2...
session target ipv4:a.3.235.1
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
!
dial-peer voice 4001 voip
destination-pattern 4xxyyy4...
session target ipv4:a.3.231.5
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
!
dial-peer voice 6001 voip
destination-pattern 6xxyyy6...
session target ipv4:a.3.231.5
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
!
telephony-service
load 7960-7940 P00303020214
max-ephones 48
max-dn 192
ip source-address a.10.1.100 port 2000
system message CME-2691
create cnf-files version-stamp 7960 Jul 15 2003 13:48:12
dialplan-pattern 1 3xxyyy3... extension-length 4 no-reg
voicemail 3105
max-conferences 8
call-forward pattern .T
web admin system name admin password cisco
dn-webedit
time-webedit
transfer-system full-consult
transfer-pattern 3...
transfer-pattern 2...
!
! Extension definitions
!
ephone-dn 1 dual-line
number 3001 secondary 3xxyyy3001
description 3xxyyy3001
name User1
call-forward busy 3105
call-forward noan 3105 timeout 10
!
!
ephone-dn 2 dual-line
number 3002 secondary 3xxyyy3002
description 3xxyyy3002
name User2
call-forward busy 3105
call-forward noan 3105 timeout 10
!
ephone-dn 2 dual-line
number 3002
description User2
name User2
call-forward busy 3105
call-forward noan 3105 timeout 10
!
!
! Dial-peers for MWI
!
ephone-dn 51
number 8000....
mwi on
!
!
ephone-dn 52
number 8001....
mwi off
!
! IP phone definitions
!
ephone 1
username "User1" password null
mac-address 0009.B7F7.5793
button 1:1
!
!
!
ephone 2
username "User2" password null
mac-address 0002.FD06.D959
button 1:2
A configuração do Cisco Unity Express é mostrada abaixo:
cue-nm-2691#
show running-config
Generating configuration:
clock timezone America/Los_Angeles
hostname cue-nm-2691
ip domain-name localdomain
! Definition of the DNS server
ip name-server a.3.180.50
ntp server a.3.229.1
software download server url "ftp://127.0.0.1/ftp"
credentials hidden "6u/dKTN/hsEuSAEfw40XlF2eFHnZfyUTSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35jwAAAAA="
groupname Administrators create
groupname customer-service create
username admin create
username User1 create
username User2 create
username User3 create
username User4 create
username User5 create
username User6 create
groupname customer-service phonenumberE164 "4xxyyy3050"
groupname customer-service phonenumber "3050"
username User1 phonenumberE164 "3xxyyy3001"
username User2 phonenumberE164 "3xxyyy3002"
username User1 phonenumber "3001"
username User2 phonenumber "3002"
username User3 phonenumber "3003"
username User4 phonenumber "3004"
username User5 phonenumber "3005"
username User6 phonenumber "3006"
groupname Administrators member admin
groupname customer-service member User2
groupname customer-service member User3
groupname Administrators privilege superuser
groupname Administrators privilege ManagePrompts
backup server url "ftp://a.3.231.201/cme2691_4nov04/"
credentials hidden "xxOaioWv/uC5WSZLs/L2XY/frZzvmJ2MSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35jwAAAAA="
ccn application autoattendant
description "autoattendant"
enabled
maxsessions 8
script "aa.aef"
parameter "MaxRetry" "3"
parameter "operExtn" "0"
parameter "welcomePrompt" "AAgreeting.wav"
end application
ccn application ciscomwiapplication
description "ciscomwiapplication"
enabled
maxsessions 8
script "setmwi.aef"
parameter "strMWI_OFF_DN" "8001"
parameter "strMWI_ON_DN" "8000"
parameter "CallControlGroupID" "0"
end application
ccn application promptmgmt
description "promptmgmt"
enabled
maxsessions 1
script "promptmgmt.aef"
end application
ccn application voicemail
description "voicemail"
enabled
maxsessions 8
script "voicebrowser.aef"
parameter "logoutUri" "http://localhost/voicemail/vxmlscripts/mbxLogout.jsp"
parameter "uri" "http://localhost/voicemail/vxmlscripts/login.vxml"
end application
ccn engine
end engine
ccn subsystem jtapi
ccm-manager address
end subsystem
ccn subsystem sip
gateway address "a.3.229.1"
end subsystem
ccn trigger sip phonenumber 3100
application "autoattendant"
enabled
maxsessions 8
end trigger
ccn trigger sip phonenumber 3105
application "voicemail"
enabled
maxsessions 8
end trigger
ccn trigger sip phonenumber 3106
application "promptmgmt"
enabled
maxsessions 1
end trigger
! Definitions of the four networking sites
network location id 2
abbreviation "S2"
email domain ch2.cue.cisco.com
name "site2-cme-3725"
end location
network location id 3
abbreviation "S3"
email domain ch3.cue.cisco.com
name "site3-cme-2691"
end location
network location id 4
abbreviation "S4"
email domain ch4.cue.cisco.com
name "site4-ccm-3725"
end location
network location id 6
abbreviation "S6"
email domain ch6.cue.cisco.com
name "site6-ccm-3745"
end location
! Definition of this site’s location ID
network local location id 3
voicemail default expiration time 60
voicemail default language en_US
voicemail default mailboxsize 5520
voicemail recording time 900
voicemail default messagesize 60
voicemail operator telephone 0
voicemail capacity time 6000
voicemail mailbox owner "User1" size 5520
end mailbox
voicemail mailbox owner "User2" size 5520
end mailbox
voicemail mailbox owner "User3" size 5520
end mailbox
voicemail mailbox owner "User4" size 5520
end mailbox
voicemail mailbox owner "User5" size 5520
end mailbox
voicemail mailbox owner "User6" size 5520
end mailbox
voicemail mailbox owner "customer-service" size 5520
description "customer-service mailbox"
zerooutnumber "3101"
end mailbox
end
cue-nm-2691#
Configuração do site 4 (roteador Cisco 3725 SRST)
As partes relevantes da configuração do roteador são mostradas abaixo:
ccm_3725#
show running-config
Building configuration...
Current configuration : 2278 bytes
!
! Last configuration change at 07:11:44 PST Wed Nov 10 2004
! NVRAM config last updated at 07:11:52 PST Wed Nov 10 2004
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname ccm_3725
!
boot-start-marker
boot system flash:c3725-ipvoice-mz.123-10.3.PI5
boot-end-marker
!
! Allow intersite H.323 calls to reach Cisco Unity Express during SRST
!
voice service voip
allow-connections h323 to sip
!
! IP address of the router
!
interface FastEthernet0/0
ip address a.3.231.10 255.255.0.0
speed auto
half-duplex
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
! IP address of Cisco Unity Express
!
interface Service-Engine1/0
ip unnumbered FastEthernet0/0
service-module ip address a.3.231.128 255.255.0.0
service-module ip default-gateway a.3.231.10
!
ip classless
ip route a.3.231.128 255.255.255.255 Service-Engine1/0
!
ip http server
ip http path flash:
!
! Dial-peer to allow calls to forward from Cisco SRST to Cisco Unity Express
!
dial-peer voice 4100 voip
destination-pattern 41..
session protocol sipv2
session target ipv4:a.3.231.128
dtmf-relay sip-notify
codec g711ulaw
no vad
!
! SRST definition to ensure Cisco Unity Express and IP Phone operation during Cisco CallManager unavailability
!
call-manager-fallback
max-conferences 8
ip source-address a.3.231.5 port 2000
max-ephones 24
max-dn 48
voicemail 4105
call-forward busy 4105
call-forward noan 4105 timeout 7
A configuração do Cisco Unity Express é mostrada abaixo:
cue-ccm3725#
show running-config
Generating configuration:
clock timezone America/Adak
hostname cue-ccm3725
ip domain-name localdomain
! Definition of the DNS server
ip name-server a.3.180.50
ntp server a.3.231.10
software download server url "ftp://127.0.0.1/ftp"
credentials hidden "6u/dKTN/hsEuSAEfw40XlF2eFHnZfyUTSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35jwAAAAA="
groupname Administrators create
username admin create
username Bob create
username anders create
username zacks create
username Bob phonenumberE164 "4xxyyy4002"
username anders phonenumberE164 "4xxyyy4001"
username Bob phonenumber "4002"
username anders phonenumber "4001"
groupname Administrators member admin
groupname Administrators member anders
groupname Administrators privilege superuser
groupname Administrators privilege ManagePrompts
backup server url "ftp://a.3.231.244/ccm3725_8nov/"
credentials hidden "GixGRq8cUmFqrOHVxftjAknfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35jwAAAAA="
ccn application abccorp
description "abccorp"
enabled
maxsessions 8
script "sample_aa.aef"
parameter "prompt_ABCWelcome" "prompt_ABCWelcome.wav"
parameter "extn_Operator" "4002"
parameter "extn_Sales" "4002"
parameter "prompt_Operator" "prompt_Operator.wav"
parameter "extn_UserEntered" "2002"
parameter "prompt_Support" "prompt_support.wav"
parameter "prompt_Hours" "prompt_Hours.wav"
parameter "extn_Support" "91877yyy2121"
parameter "prompt_Extension" "prompt_Extension.wav"
parameter "prompt_Sales" "prompt_Sales.wav"
end application
ccn application autoattendant
description "autoattendant"
enabled
maxsessions 8
script "aa.aef"
parameter "MaxRetry" "3"
parameter "operExtn" "0"
parameter "welcomePrompt" "AAWelcome.wav"
end application
ccn application ciscomwiapplication
description "ciscomwiapplication"
enabled
maxsessions 8
script "setmwi.aef"
parameter "strMWI_OFF_DN" "8001"
parameter "strMWI_ON_DN" "8000"
parameter "CallControlGroupID" "0"
end application
ccn application promptmgmt
description "promptmgmt"
enabled
maxsessions 1
script "promptmgmt.aef"
end application
ccn application voicemail
description "voicemail"
enabled
maxsessions 8
script "voicebrowser.aef"
parameter "logoutUri" "http://localhost/voicemail/vxmlscripts/mbxLogout.jsp"
parameter "uri" "http://localhost/voicemail/vxmlscripts/login.vxml"
end application
ccn engine
end engine
ccn subsystem jtapi
ctiport 4901 4902 4903 4904
ccm-manager address a.3.231.5
ccm-manager
credentials hidden "QiUfMZRFsRBqrOHVxftjAknfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35jwAAAAA="
end subsystem
ccn subsystem sip
gateway address "a.3.231.10"
end subsystem
ccn trigger jtapi phonenumber 4100
application "autoattendant"
enabled
locale "en_US"
maxsessions 8
end trigger
ccn trigger jtapi phonenumber 4101
application "abccorp"
enabled
locale "en_US"
maxsessions 8
end trigger
ccn trigger jtapi phonenumber 4105
application "voicemail"
enabled
locale "en_US"
maxsessions 8
end trigger
ccn trigger jtapi phonenumber 4106
application "promptmgmt"
enabled
locale "en_US"
maxsessions 1
end trigger
ccn trigger sip phonenumber 4100
application "autoattendant"
enabled
locale "en_US"
maxsessions 8
end trigger
ccn trigger sip phonenumber 4101
application "abccorp"
enabled
locale "en_US"
maxsessions 8
end trigger
ccn trigger sip phonenumber 4105
application "voicemail"
enabled
locale "en_US"
maxsessions 8
end trigger
ccn trigger sip phonenumber 4106
application "promptmgmt"
enabled
locale "en_US"
maxsessions 1
end trigger
! Definitions of the four networking sites
network location id 2
abbreviation "S2"
email domain ch2.cue.cisco.com
name "site2-cme-3725"
end location
network location id 3
abbreviation "S3"
email domain ch3.cue.cisco.com
name "site3-cme-2691"
end location
network location id 4
abbreviation "S4"
email domain ch4.cue.cisco.com
name "site4-ccm-3725"
end location
network location id 6
abbreviation "S6"
email domain ch6.cue.cisco.com
name "site6-ccm-3745"
end location
! Definition of this site’s location ID
network local location id 4
voicemail default expiration time 30
voicemail default language en_US
voicemail default mailboxsize 3000
voicemail recording time 900
voicemail default messagesize 60
voicemail operator telephone 0
voicemail capacity time 6000
voicemail mailbox owner "Bob" size 3000
end mailbox
voicemail mailbox owner "anders" size 3000
end mailbox
voicemail mailbox owner "zacks" size 3000
end mailbox
end
Configuração do site 6 (roteador Cisco 3745 SRST)
As partes relevantes da configuração do roteador são mostradas abaixo:
Relevant extracts of the router’s configuration are shown below:
ccm_3745#
show running-config
Building configuration...
Current configuration : 3295 bytes
!
! Last configuration change at 02:46:54 UTC Fri Apr 12 2002
! NVRAM config last updated at 17:20:53 UTC Thu Apr 11 2002
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname ccm_3745
!
boot-start-marker
boot system flash:c3745-ipvoice-mz.123-10.3.PI5
boot-end-marker
!
!
! Allow intersite H.323 calls to reach Cisco Unity Express during SRST
!
voice service voip
allow-connections h323 to sip
!
! IP address of the router
!
interface FastEthernet0/0
ip address a.3.245.1 255.255.0.0
speed auto
half-duplex
no mop enabled
!
interface FastEthernet0/1
ip address 172.19.153.31 255.255.0.0
duplex auto
speed auto
!
! IP address of Cisco Unity Express
!
interface Service-Engine1/0
ip unnumbered FastEthernet0/0
service-module ip address a.3.245.128 255.255.0.0
service-module ip default-gateway a.3.245.1
!
!
ip classless
ip route a.3.245.128 255.255.255.255 Service-Engine1/0
!
ip http server
ip http path flash:
!
!
! Dial-peer to allow calls to forward from Cisco SRST to Cisco Unity Express
!
dial-peer voice 6100 voip
destination-pattern 61..
session protocol sipv2
session target ipv4:a.3.245.128
dtmf-relay sip-notify
codec g711ulaw
no vad
!
! SRST definition to ensure Cisco Unity Express and IP Phone operation during Cisco CallManager unavailability
!
call-manager-fallback
max-conferences 8
ip source-address a.3.231.5 port 2000
max-ephones 24
max-dn 48
voicemail 6105
call-forward busy 6105
A configuração do Cisco Unity Express é mostrada abaixo:
cue-ccm3745#
show running-config
Generating configuration:
clock timezone America/Los_Angeles
hostname cue-ccm3745
ip domain-name localdomain
! Definition of the DNS server
ip name-server a.3.180.50
ntp server a.3.233.100
software download server url "ftp://127.0.0.1/ftp"
credentials hidden "6u/dKTN/hsEuSAEfw40XlF2eFHnZfyUTSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35jwAAAAA="
groupname Administrators create
groupname Broadcasters create
username admin create
username Yvon create
username Zack create
username Yvon phonenumberE164 "6xxyyy6001"
username Zack phonenumberE164 "6xxyyy6002"
username Yvon phonenumber "6001"
username Zack phonenumber "6002"
groupname Administrators member admin
groupname Administrators member Yvon
groupname Administrators privilege superuser
groupname Administrators privilege ManagePrompts
backup server url "ftp://a.3.231.243/ccm3745_5nov/"
credentials hidden "GixGRq8cUmFqrOHVxftjAknfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35jwAAAAA="
ccn application autoattendant
description "autoattendant"
enabled
maxsessions 8
script "aa.aef"
parameter "MaxRetry" "3"
parameter "operExtn" "0"
parameter "welcomePrompt" "AAWelcome.wav"
end application
ccn application ciscomwiapplication
description "ciscomwiapplication"
enabled
maxsessions 8
script "setmwi.aef"
parameter "strMWI_OFF_DN" "8001"
parameter "strMWI_ON_DN" "8000"
parameter "CallControlGroupID" "0"
end application
ccn application promptmgmt
description "promptmgmt"
enabled
maxsessions 1
script "promptmgmt.aef"
end application
ccn application voicemail
description "voicemail"
enabled
maxsessions 8
script "voicebrowser.aef"
parameter "logoutUri" "http://localhost/voicemail/vxmlscripts/mbxLogout.jsp"
parameter "uri" "http://localhost/voicemail/vxmlscripts/login.vxml"
end application
ccn engine
end engine
ccn subsystem jtapi
ctiport 6901 6902 6903 6904
ccm-manager address a.3.231.5
ccm-manager
credentials hidden "1anJW38IVSZld67dzhL9pEnfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35jwAAAAA="
end subsystem
ccn subsystem sip
gateway address "a.3.45.1"
end subsystem
ccn trigger jtapi phonenumber 6100
application "autoattendant"
enabled
locale "en_US"
maxsessions 8
end trigger
ccn trigger jtapi phonenumber 6105
application "voicemail"
enabled
locale "en_US"
maxsessions 8
end trigger
ccn trigger jtapi phonenumber 6106
application "promptmgmt"
enabled
locale "en_US"
maxsessions 1
end trigger
ccn trigger sip phonenumber 6100
application "autoattendant"
enabled
locale "en_US"
maxsessions 8
end trigger
ccn trigger sip phonenumber 6105
application "voicemail"
enabled
locale "en_US"
maxsessions 8
end trigger
ccn trigger sip phonenumber 6106
application "promptmgmt"
enabled
locale "en_US"
maxsessions 1
end trigger
! Definitions of the four networking sites
network location id 2
abbreviation "S2"
email domain ch2.cue.cisco.com
name "site2-cme-3725"
end location
network location id 3
abbreviation "S3"
email domain ch3.cue.cisco.com
name "site3-cme-2691"
end location
network location id 4
abbreviation "S4"
email domain ch4.cue.cisco.com
name "site4-ccm-3725"
end location
network location id 6
abbreviation "S6"
email domain ch6.cue.cisco.com
name "site6-ccm-3745"
end location
! Definition of this site’s location ID
network local location id 6
voicemail default expiration time 30
voicemail default language en_US
voicemail default mailboxsize 3000
voicemail recording time 900
voicemail default messagesize 60
voicemail operator telephone 0
voicemail capacity time 6000
voicemail mailbox owner "Yvon" size 3000
end mailbox
voicemail mailbox owner "Zack" size 3000
end mailbox
end
Verificar
Esta seção fornece informações que você pode usar para confirmar se sua configuração está funcionando adequadamente.
Troubleshooting
Esta seção fornece informações que podem ser usadas para o troubleshooting da sua configuração.
Comandos para Troubleshooting
Nota: Antes de emitir comandos de depuração, consulte as informações importantes sobre eles.
Os seguintes comandos de rastreamento podem ser emitidos no sistema de emissão ou de recepção do Cisco Unity Express para monitorar as atividades SMTP e VPIM entre eles.
Monitora eventos SMTP
Monitora eventos VPIM
Exibe conteúdo do buffer de rastreamento na tela
O seguinte é um exemplo de saída para os comandos trace para o local de emissão (local 3) ao enviar uma mensagem da extensão 3001 do local 3 para situar 2 a extensão 2xxyyy2002.
cue-nm-2691# trace networking smtp all cue-nm-2691# trace networking vpim all cue-nm-2691# show trace buffer tail Press <CTRL-C> to exit... 7751 10/26 14:20:59.146 netw smtp 5 221 closing channel 2833 10/26 16:00:55.154 netw smtp 2 2833 10/26 16:00:55.174 netw smtp 1 8386 10/26 16:00:55.193 netw smtp 3 ch2.cue.cisco.com 8386 10/26 16:00:55.204 netw smtp 4 8386 10/26 16:00:55.218 netw smtp 6 220 ch2.cue.cisco.com Simple Mail Transfer Service Ready 8386 10/26 16:00:55.218 netw smtp 5 EHLO 8386 10/26 16:00:55.223 netw smtp 6 250-ch2.cue.cisco.com (Cisco Unity Express) 8386 10/26 16:00:55.224 netw smtp 6 250-X-VPIM-Wave 8386 10/26 16:00:55.225 netw smtp 6 250-X-Broadcast 8386 10/26 16:00:55.227 netw smtp 6 250-DSN NOTIFY 8386 10/26 16:00:55.229 netw smtp 6 250 SIZE 2833 10/26 16:00:55.239 netw smtp 2 8387 10/26 16:00:55.269 netw smtp 3 ch3.cue.cisco.com 2834 10/26 16:00:55.272 netw smtp 2 2834 10/26 16:00:55.276 netw smtp 3 socket hostName: cue-nm-2691.localdomain, hostAddress: a.3.229.128 2834 10/26 16:00:55.307 netw smtp 3 Resolved to domain: ch3.cue.cisco.com 8387 10/26 16:00:55.309 netw smtp 4 8388 10/26 16:00:55.325 netw smtp 5 Initial connection message 2834 10/26 16:00:55.328 netw smtp 1 8387 10/26 16:00:55.329 netw smtp 6 220 ch3.cue.cisco.com Simple Mail Transfer Service Ready 8387 10/26 16:00:55.329 netw smtp 5 EHLO 8388 10/26 16:00:55.331 netw smtp 6 UNKNOWN: EHLO ch3.cue.cisco.com 8388 10/26 16:00:55.332 netw smtp 5 250-ch3.cue.cisco.com 8387 10/26 16:00:55.332 netw smtp 6 250-ch3.cue.cisco.com (Cisco Unity Express) 8387 10/26 16:00:55.332 netw smtp 6 250-X-VPIM-Wave 8387 10/26 16:00:55.334 netw smtp 6 250-X-Broadcast 8387 10/26 16:00:55.335 netw smtp 6 250-DSN NOTIFY 8387 10/26 16:00:55.336 netw smtp 6 250 SIZE 8386 10/26 16:00:55.724 netw smtp 5 MAIL FROM 3001@ch3.cue.cisco.com 8386 10/26 16:00:55.738 netw smtp 6 250 ok 8386 10/26 16:00:55.739 netw smtp 5 RCPT TO 2xxyyy2002@ch2.cue.cisco.com 8386 10/26 16:00:55.744 netw smtp 6 250 ok 8386 10/26 16:00:55.746 netw smtp 5 DATA 8386 10/26 16:00:55.750 netw smtp 6 354 Start mail input; end with <CRLF>.<CRLF> 8386 10/26 16:00:55.755 netw vpim 3 VPIM 8386 10/26 16:00:55.775 netw vpim 3 VPIM: To: <2xxyyy2002@ch2.cue.cisco.com> 8386 10/26 16:00:55.777 netw vpim 3 VPIM: From: User One<3001@ch3.cue.cisco.com> 8386 10/26 16:00:55.779 netw vpim 3 VPIM: Date: Tue, 26 Oct 2004 16:00:54 -0700 (PDT) 8386 10/26 16:00:55.779 netw vpim 3 VPIM: MIME-Version: 1.0 (Voice 2.0) 8386 10/26 16:00:55.779 netw vpim 3 VPIM: Content-Type: Multipart/Voice-Message; Version=2.0; 8386 10/26 16:00:55.780 netw vpim 3 VPIM: Boundary="==VpimMsg==1098831655752" 8386 10/26 16:00:55.780 netw vpim 3 VPIM: Content-Transfer-Encoding: 7bit 8386 10/26 16:00:55.780 netw vpim 3 VPIM: Message-ID: <1098831654914_0@ch3.cue.cisco.com> 8386 10/26 16:00:55.780 netw vpim 3 VPIM: 8386 10/26 16:00:55.781 netw vpim 3 VPIM: --==VpimMsg==1098831655752 8386 10/26 16:00:55.782 netw vpim 3 VPIM: Content-Type: text/directory; charset=us-ascii; profile=vCard 8386 10/26 16:00:55.782 netw vpim 3 VPIM: Content-Transfer-Encoding: 7bit 8386 10/26 16:00:55.782 netw vpim 3 VPIM: Content-Disposition: attachment; filename="User One.vcf" 8386 10/26 16:00:55.782 netw vpim 3 VPIM: 8386 10/26 16:00:55.783 netw vpim 3 VPIM: BEGIN:vCard 8386 10/26 16:00:55.783 netw vpim 3 VPIM: FN:User One 8386 10/26 16:00:55.783 netw vpim 3 VPIM: EMAIL;TYPE=INTERNET;TYPE=VPIM:3001@ch3.cue.cisco.com 8386 10/26 16:00:55.783 netw vpim 3 VPIM: TEL:3001 8386 10/26 16:00:55.784 netw vpim 3 VPIM: VERSION: 3.0 8386 10/26 16:00:55.784 netw vpim 3 VPIM: END:vCard 8386 10/26 16:00:55.784 netw vpim 3 VPIM: 8387 10/26 16:00:55.843 netw smtp 5 MAIL FROM 3001@ch3.cue.cisco.com 8388 10/26 16:00:55.848 netw smtp 6 EHLO : MAIL FROM: <3001@ch3.cue.cisco.com> 8388 10/26 16:00:55.852 netw smtp 5 250 ok 8387 10/26 16:00:55.852 netw smtp 6 250 ok 8387 10/26 16:00:55.854 netw smtp 5 RCPT TO 3xxyyy3002@ch3.cue.cisco.com 8388 10/26 16:00:55.856 netw smtp 6 MAIL FROM:: RCPT TO: <3xxyyy3002@ch3.cue.cisco.com> 8388 10/26 16:00:55.856 netw smtp 5 250 ok 8387 10/26 16:00:55.856 netw smtp 6 250 ok 8387 10/26 16:00:55.858 netw smtp 5 DATA 8388 10/26 16:00:55.860 netw smtp 6 RCPT TO:: DATA 8388 10/26 16:00:55.860 netw smtp 5 354 Start data 8387 10/26 16:00:55.861 netw smtp 6 354 Start mail input; end with <CRLF>.<CRLF> 8387 10/26 16:00:55.865 netw vpim 3 VPIM 8387 10/26 16:00:55.884 netw vpim 3 VPIM: To: <3xxyyy3002@ch3.cue.cisco.com> 8387 10/26 16:00:55.885 netw vpim 3 VPIM: From: User One<3001@ch3.cue.cisco.com> 8387 10/26 16:00:55.887 netw vpim 3 VPIM: Date: Tue, 26 Oct 2004 16:00:54 -0700 (PDT) 8387 10/26 16:00:55.888 netw vpim 3 VPIM: MIME-Version: 1.0 (Voice 2.0) 8387 10/26 16:00:55.888 netw vpim 3 VPIM: Content-Type: Multipart/Voice-Message; Version=2.0; 8387 10/26 16:00:55.888 netw vpim 3 VPIM: Boundary="==VpimMsg==1098831655863" 8387 10/26 16:00:55.888 netw vpim 3 VPIM: Content-Transfer-Encoding: 7bit 8387 10/26 16:00:55.889 netw vpim 3 VPIM: Message-ID: <1098831654914_0@ch3.cue.cisco.com> 8387 10/26 16:00:55.889 netw vpim 3 VPIM: 8387 10/26 16:00:55.890 netw vpim 3 VPIM: --==VpimMsg==1098831655863 8387 10/26 16:00:55.890 netw vpim 3 VPIM: Content-Type: text/directory; charset=us-ascii; profile=vCard 8387 10/26 16:00:55.890 netw vpim 3 VPIM: Content-Transfer-Encoding: 7bit 8387 10/26 16:00:55.891 netw vpim 3 VPIM: Content-Disposition: attachment; filename="User One.vcf" 8387 10/26 16:00:55.891 netw vpim 3 VPIM: 8387 10/26 16:00:55.891 netw vpim 3 VPIM: BEGIN:vCard 8387 10/26 16:00:55.891 netw vpim 3 VPIM: FN:User One 8387 10/26 16:00:55.891 netw vpim 3 VPIM: EMAIL;TYPE=INTERNET;TYPE=VPIM:3001@ch3.cue.cisco.com 8387 10/26 16:00:55.892 netw vpim 3 VPIM: TEL:3001 8387 10/26 16:00:55.892 netw vpim 3 VPIM: VERSION: 3.0 8387 10/26 16:00:55.892 netw vpim 3 VPIM: END:vCard 8387 10/26 16:00:55.892 netw vpim 3 VPIM: 8386 10/26 16:00:55.901 netw vpim 3 VPIM: --==VpimMsg==1098831655752 8386 10/26 16:00:55.902 netw vpim 3 VPIM: Content-Type: Audio/x-wav 8386 10/26 16:00:55.906 netw vpim 3 VPIM: Content-Transfer-Encoding: Base64 8386 10/26 16:00:55.906 netw vpim 3 VPIM: Content-Disposition: inline; voice=Originator-Spoken-Name 8386 10/26 16:00:55.910 netw vpim 3 VPIM: 8388 10/26 16:00:55.938 netw vpim 4 VPIM: To: <3xxyyy3002@ch3.cue.cisco.com> 8388 10/26 16:00:55.939 netw vpim 4 VPIM: From: User One<3001@ch3.cue.cisco.com> 8388 10/26 16:00:55.941 netw vpim 4 VPIM: Date: Tue, 26 Oct 2004 16:00:54 -0700 (PDT) 8388 10/26 16:00:55.943 netw vpim 4 VPIM: MIME-Version: 1.0 (Voice 2.0) 8388 10/26 16:00:55.945 netw vpim 4 VPIM: Content-Type: Multipart/Voice-Message; Version=2.0;Boundary="==VpimMsg==1098831655863" 8388 10/26 16:00:55.946 netw vpim 4 VPIM: Content-Transfer-Encoding: 7bit 8388 10/26 16:00:55.948 netw vpim 4 VPIM: Message-ID: <1098831654914_0@ch3.cue.cisco.com> 8388 10/26 16:00:55.949 netw vpim 4 VPIM: 8388 10/26 16:00:55.951 netw vpim 4 VPIM: --==VpimMsg==1098831655863 8387 10/26 16:00:55.967 netw vpim 3 VPIM: --==VpimMsg==1098831655863 8387 10/26 16:00:55.967 netw vpim 3 VPIM: Content-Type: Audio/x-wav 8387 10/26 16:00:55.968 netw vpim 3 VPIM: Content-Transfer-Encoding: Base64 8387 10/26 16:00:55.968 netw vpim 3 VPIM: Content-Disposition: inline; voice=Originator-Spoken-Name 8387 10/26 16:00:55.968 netw vpim 3 VPIM: 8388 10/26 16:00:55.983 netw vpim 1 Message 8388 10/26 16:00:55.986 netw vpim 4 VPIM: Content-Type: text/directory; charset=us-ascii; profile=vCard 8388 10/26 16:00:55.987 netw vpim 4 vCard: Content-Transfer-Encoding: 7bit 8388 10/26 16:00:55.988 netw vpim 4 vCard: Content-Disposition: attachment; filename="User One.vcf" 8388 10/26 16:00:55.990 netw vpim 4 vCard: 8388 10/26 16:00:55.991 netw vpim 4 vCard: BEGIN:vCard 8388 10/26 16:00:55.992 netw vpim 4 vCard: FN:User One 8388 10/26 16:00:56.003 netw vpim 4 vCard: EMAIL;TYPE=INTERNET;TYPE=VPIM:3001@ch3.cue.cisco.com 8388 10/26 16:00:56.005 netw vpim 4 vCard: TEL:3001 8388 10/26 16:00:56.006 netw vpim 4 vCard: VERSION: 3.0 8388 10/26 16:00:56.007 netw vpim 4 vCard: END:vCard 8388 10/26 16:00:56.008 netw vpim 4 vCard: 8388 10/26 16:00:56.010 netw vpim 4 vCard: --==VpimMsg==1098831655863 8388 10/26 16:00:56.012 netw vpim 4 VPIM: Content-Type: Audio/x-wav 8388 10/26 16:00:56.014 netw vpim 4 VPIM: Content-Transfer-Encoding: Base64 8388 10/26 16:00:56.015 netw vpim 4 VPIM: Content-Disposition: inline; voice=Originator-Spoken-Name 8388 10/26 16:00:56.020 netw vpim 5 25802 8387 10/26 16:00:56.148 netw vpim 3 VPIM: UklGRjI3AABXQVZFZm10IBIAAAAHAAEAQB8AAEAfAAABAAgAAABmYWN0BAAAAAA3AABkYXRhADcA APT6/fr6+/19eXZ4e3l4eXt9/fv9fX37/f/9/f/7/X17eXt5eH37/f34+vv7+Pv/+/v7/339//99 eHh7e3l4fX3//Xt9/33///3///v6+Pb7/fv9//99/317e3t9/319/3l0eHn//3t9ff/9+Pj///r0 9vb2+/99/319/Xl2/319///9//99e//9fX19ffv/ffv//fv69vj6+vv/ff99fX12dnh5fXt9+//9 +33//f//eXh7+/39+v/9+vr6+/v9ff99//r///v9/fr7+/v/e3h5e3h2eHh5/f17//v///97//j6 ...
O seguinte é um exemplo de saída para os comandos trace para o local de recepção (local 2) ao enviar uma mensagem da extensão 3001 do local 3 para situar 2 a extensão 2xxyyy2002.
cue-cme3725# trace networking smtp all cue-cme3725# trace networking vpim all cue-cme3725# show trace buffer tail Press <CTRL-C> to exit... 9301 11/12 14:24:02.058 netw smtp 5 221 closing channel 3384 11/12 14:26:10.899 netw smtp 2 3384 11/12 14:26:10.902 netw smtp 3 socket hostName: a.3.229.128, hostAddress: a.3.229.128 3384 11/12 14:26:10.903 netw smtp 3 hostname: a.3.229.128 found in good address cache 3384 11/12 14:26:10.915 netw smtp 1 9312 11/12 14:26:10.920 netw smtp 5 Initial connection message 9312 11/12 14:26:10.926 netw smtp 6 UNKNOWN: EHLO ch3.cue.cisco.com 9312 11/12 14:26:10.926 netw smtp 5 250-ch2.cue.cisco.com 9312 11/12 14:26:11.431 netw smtp 6 EHLO : MAIL FROM: <3001@ch3.cue.cisco.com> 9312 11/12 14:26:11.437 netw smtp 5 250 ok 9312 11/12 14:26:11.446 netw smtp 6 MAIL FROM:: RCPT TO: <2xxyyy2002@ch2.cue.cisco.com> 9312 11/12 14:26:11.447 netw smtp 5 250 ok 9312 11/12 14:26:11.452 netw smtp 6 RCPT TO:: DATA 9312 11/12 14:26:11.453 netw smtp 5 354 Start data 9312 11/12 14:26:11.513 netw vpim 4 VPIM: To: <2xxyyy2002@ch2.cue.cisco.com> 9312 11/12 14:26:11.516 netw vpim 4 VPIM: From: User One<3001@ch3.cue.cisco.com> 9312 11/12 14:26:11.520 netw vpim 4 VPIM: Date: Tue, 26 Oct 2004 16:00:54 -0700 (PDT) 9312 11/12 14:26:11.524 netw vpim 4 VPIM: MIME-Version: 1.0 (Voice 2.0) 9312 11/12 14:26:11.527 netw vpim 4 VPIM: Content-Type: Multipart/Voice-Message; Version=2.0;Boundary="==VpimMsg==1098831655752" 9312 11/12 14:26:11.531 netw vpim 4 VPIM: Content-Transfer-Encoding: 7bit 9312 11/12 14:26:11.534 netw vpim 4 VPIM: Message-ID: <1098831654914_0@ch3.cue.cisco.com> 9312 11/12 14:26:11.537 netw vpim 4 VPIM: 9312 11/12 14:26:11.540 netw vpim 4 VPIM: --==VpimMsg==1098831655752 9312 11/12 14:26:11.552 netw vpim 1 Message 9312 11/12 14:26:11.558 netw vpim 4 VPIM: Content-Type: text/directory; charset=us-ascii; profile=vCard 9312 11/12 14:26:11.561 netw vpim 4 vCard: Content-Transfer-Encoding: 7bit 9312 11/12 14:26:11.564 netw vpim 4 vCard: Content-Disposition: attachment; filename="User One.vcf" 9312 11/12 14:26:11.568 netw vpim 4 vCard: 9312 11/12 14:26:11.571 netw vpim 4 vCard: BEGIN:vCard 9312 11/12 14:26:11.574 netw vpim 4 vCard: FN:User One 9312 11/12 14:26:11.577 netw vpim 4 vCard: EMAIL;TYPE=INTERNET;TYPE=VPIM:3001@ch3.cue.cisco.com 9312 11/12 14:26:11.580 netw vpim 4 vCard: TEL:3001 9312 11/12 14:26:11.583 netw vpim 4 vCard: VERSION: 3.0 9312 11/12 14:26:11.586 netw vpim 4 vCard: END:vCard 9312 11/12 14:26:11.589 netw vpim 4 vCard: 9312 11/12 14:26:11.612 netw vpim 4 vCard: --==VpimMsg==1098831655752 9312 11/12 14:26:11.618 netw vpim 4 VPIM: Content-Type: Audio/x-wav 9312 11/12 14:26:11.622 netw vpim 4 VPIM: Content-Transfer-Encoding: Base64 9312 11/12 14:26:11.625 netw vpim 4 VPIM: Content-Disposition: inline; voice=Originator-Spoken-Name 9312 11/12 14:26:11.633 netw vpim 5 34010 9312 11/12 14:26:11.962 netw vpim 4 VPIM audio: UklGRjI3AABXQVZFZm10IBIAAAAHAAEAQB8AAEAfAAABAAgAAABmYWN0BAAAAAA3AABkYXRhADcA 9312 11/12 14:26:11.963 netw vpim 4 VPIM audio: APT6/fr6+/19eXZ4e3l4eXt9/fv9fX37/f/9/f/7/X17eXt5eH37/f34+vv7+Pv/+/v7/339//99 9312 11/12 14:26:11.965 netw vpim 4 VPIM audio: eHh7e3l4fX3//Xt9/33///3///v6+Pb7/fv9//99/317e3t9/319/3l0eHn//3t9ff/9+Pj///r0 9312 11/12 14:26:11.967 netw vpim 4 VPIM audio: 9vb2+/99/319/Xl2/319///9//99e//9fX19ffv/ffv//fv69vj6+vv/ff99fX12dnh5fXt9+//9 9312 11/12 14:26:11.968 netw vpim 4 VPIM audio: +33//f//eXh7+/39+v/9+vr6+/v9ff99//r///v9/fr7+/v/e3h5e3h2eHh5/f17//v///97//j6 ...
Informações Relacionadas
FeedbackDeixe-nos ajudar
- Abrir um caso de suporte
- (É necessário um Contrato de Serviço da Cisco)