Solucionar falhas de hardware em supervisores e placas de linha do Catalyst 9600
Contents
Introdução
Este documento descreve como identificar, isolar e solucionar problemas de sintomas de falhas de hardware em Supervisores e Placas de Linha do Catalyst 9600.
Pré-requisitos
Requisitos
Não existem requisitos específicos para este documento.
Componentes Utilizados
As informações neste documento são baseadas nos Catalyst 9600 Series Switches.
As informações neste documento foram criadas a partir de dispositivos em um ambiente de laboratório específico. Todos os dispositivos utilizados neste documento foram iniciados com uma configuração (padrão) inicial. Se a rede estiver ativa, certifique-se de que você entenda o impacto potencial de qualquer comando.
Terminologia
| Termo |
Definição |
Contexto |
| Supervisor |
O Supervisor Engine 1 do Cisco Catalyst 9600 Series é alimentado por três ASICs UADP 3.0 e um processador de CPU x86. Os três ASICs estão interconectados com uma interconexão ASIC de 3,2 Tbps em cada ASIC. O Sup-1 fornece 9,6 Tbps (4,8 Tbps full duplex). Com o chassi do Cisco Catalyst 9606R, cada slot tem 2,4 Tbps com Sup-1. |
Este documento contém comandos para isolar a falha de hardware nos mecanismos do Supervisor. |
| Power On Self Test (P.O.S.T.) |
Depois que o Supervisor e as Placas de Linha são inicializados após a inicialização, um POST (Power On Self Test, autoteste de inicialização) é executado para garantir a integridade de hardware dos módulos. O POST também é executado durante a Inserção e Remoção On-line (OIR - Online Insertion & Removal) de uma placa de linha. |
O comando show post exibe os resultados desses testes. |
| Subsistemas genéricos de diagnóstico online (GOLD.) |
Os testes GOLD são executados depois que o sistema está on-line. Alguns testes são executados periodicamente como testes de Monitoramento de integridade. Todos os testes podem ser executados sob demanda pelo usuário. |
É usado para detectar falhas de hardware do módulo. |
| Inserção e Remoção On-line (OI) |
Esse recurso pode executar o ciclo de energia de um módulo em um determinado slot por meio da interface de linha de comando (CLI). Isso é útil quando não há um recurso no local que possa recolocar o módulo psiquicamente. |
O.I.R. é um excelente recurso para executar falhas isoladas de hardware em módulos. |
Visão geral do chassi
| Catalyst C9606-R |
|
 |
Troubleshooting
Sintomas de problemas de hardware do módulo
| Sintoma |
Possível causa raiz |
|
O módulo não foi instalado corretamente, não foi inicializado ou encontrou uma falha de hardware devido à falha do P.O.S.T. |
Verificar o status do módulo
- É importante primeiro verificar se o chassi reconhece o módulo.
- O status ideal para um módulo é 'ok'.
| Status do módulo |
Possível causa raiz |
Ação |
| ok |
N/A. |
Nenhum |
| pós-falha |
Possível falha de hardware. |
Consulte Troubleshooting de Status do Módulo. |
| outros |
Falha ao inicializar o módulo. |
Consulte Troubleshooting de Status do Módulo. |
| Não listado na saída |
Não instalado corretamente ou não recebendo energia suficiente. |
Verifique o orçamento de energia disponível. Inspecionar visualmente o status L.E.D. do módulo. |
Cat9600#show module Chassis Type: C9606R Mod Ports Card Type Model Serial No. ---+-----+--------------------------------------+--------------+-------------- 1 24 24-Port 40GE/12-Port 100GE C9600-LC-24C 2 48 48-Port 10GE / 25GE C9600-LC-48YL 3 0 Supervisor 1 Module C9600-SUP-1 4 0 Supervisor 1 Module C9600-SUP-1 Mod MAC addresses Hw Fw Sw Status ---+--------------------------------+----+------------+------------------+-------- 1 DC8C.37A0.C880 to DC8C.37A0.C8FF 1.0 17.1.1[FC2] 16.12.03 post-fail 2 DC8C.3773.1E00 to DC8C.3773.1E7F 1.0 17.1.1[FC2] 16.12.03 ok 3 DC8C.379F.ED80 to DC8C.379F.EDFF 1.0 17.1.1[FC2] 16.12.03 ok 4 DC8C.379F.EDF1 to DC8C.379F.EDF9 1.0 17.1.1[FC2] 16.12.03 ok //other example Mod MAC addresses Hw Fw Sw Status ---+--------------------------------+----+------------+------------------+-------- 1 DC8C.37A0.C880 to DC8C.37A0.C8FF 1.3 17.3.1r[FC2] 17.03.05 power-deny 2 DC8C.37A0.C880 to DC8C.37A0.C8FF 1.3 17.3.1r[FC2] 17.03.05 power-deny 3 DC8C.37A0.C880 to DC8C.37A0.C8FF 1.4 17.3.1r[FC2] 17.03.05 ok
Solucionar problemas de status do módulo
| Sintoma |
Ação |
| Módulo não listado ou o status não é 'ok'. |
Continue com as próximas etapas. |
Verificar o Syslog
Placa de linha off-line
%IOSXE_OIR-6-OFFLINECARD: Card (rp) offline in slot R1 %IOSXE_OIR-6-REMSPA: SPA removed from subslot 6/0, interfaces disabled %SPA_OIR-6-OFFLINECARD: SPA (C9600-LC-48TX) offline in subslot 6/0
Problema de orçamento de energia
%CMRP_PFU-3-PWR_MGMT_LC_SHUTDOWN: R0/0: cmand: WARNING: Linecard in slot 6 with priority 0 and a power requirement of 315 watts has shutdown. %CMRP_PFU-3-PWR_MGMT_ALARM: Chassis 1 R0/0: cmand: WARNING: System does not have sufficient input power for minimum reliable operation requiring 1161 watts. The system needs 1101 watts of additional power.
falha do teste de diagnóstico
*May 29 02:10:19.523: %PM-4-ERR_DISABLE: diagnostics error detected on Fo2/0/1, putting Fo2/0/1 in err-disable state
Verificar o tempo de atividade do módulo
- O Onboard Failure Logging (OBFL) nos dá uma ideia para recarregar motivos como comando de recarregamento, exceção de software, desligamento e assim por diante.
- Verifique os carimbos de data/hora que podem estar correlacionados à perda súbita de energia para o módulo ou fator externo que contribui para a queda do módulo.
Cat9600#show logging onboard rp (active|standby) uptime detail
-------------------------------------------------------------------------------- UPTIME SUMMARY INFORMATION -------------------------------------------------------------------------------- First customer power on : 08/28/2021 13:08:41 Total uptime : 0 years 41 weeks 2 days 15 hours 10 minutes <-- Total Uptime Total downtime : 0 years 7 weeks 6 days 7 hours 11 minutes Number of resets : 14 <-- Total number of resets Number of slot changes : 0 Current reset reason : PowerOn <-- Last reload reason Current reset timestamp : 11/06/2021 17:25:29 Current slot : 3 Chassis type : 55 Current uptime : 0 years 39 weeks 1 days 18 hours 5 minutes <-- Current Uptime -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- UPTIME CONTINUOUS INFORMATION -------------------------------------------------------------------------------- Time Stamp | Reset | Uptime MM/DD/YYYY HH:MM:SS | Reason | years weeks days hours minutes -------------------------------------------------------------------------------- 08/28/2021 13:08:41 PowerOn 0 0 0 0 0 08/28/2021 13:16:29 Reload 0 0 0 0 0 08/28/2021 13:29:28 Reload 0 0 0 0 5 08/28/2021 13:42:30 Reload 0 0 0 0 5 08/28/2021 13:55:14 Image Install 0 0 0 0 5 <-- Reset history by reason
Cat9600#show logging onboard slot (1|2|4|5|6|7) uptime detail -------------------------------------------------------------------------------- UPTIME SUMMARY INFORMATION -------------------------------------------------------------------------------- First customer power on : 08/08/2018 09:30:33 Total uptime : 0 years 11 weeks 1 days 10 hours 40 minutes Total downtime : 4 years 32 weeks 1 days 23 hours 25 minutes Number of resets : 81 Number of slot changes : 5 Current reset reason : CP_RESET_CPU_GOT_RESET Current reset timestamp : 05/24/2023 19:35:58 Current slot : 1 Chassis type : 30 Current uptime : 0 years 2 weeks 0 days 0 hours 0 minutes -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- UPTIME CONTINUOUS INFORMATION -------------------------------------------------------------------------------- Time Stamp | Reset | Uptime MM/DD/YYYY HH:MM:SS | Reason | years weeks days hours minutes -------------------------------------------------------------------------------- 04/26/2021 21:39:45 CP_RESET_CPU_GOT_RESET 0 0 0 0 0 04/27/2021 14:12:04 CP_RESET_POWER_ON 0 0 0 6 0 04/28/2021 14:39:30 CP_RESET_POWER_ON 0 0 0 14 0 04/30/2021 12:46:59 CP_RESET_POWER_ON 0 0 0 13 0
Verificar POST
Exemplo de falha de POST
Cat9600#show post
Stored system POST messages:
Switch C9606R
--------------
Fri May 29 02:10:18 2020 POST: Module: 1 Mac Loopback Begin
Fri May 29 02:10:18 2020 POST: Module: 1 Mac Loopback: loopback Test: End, Status Passed
Fri May 29 02:10:18 2020 POST: Module: 2 Mac Loopback Begin
Fri May 29 02:10:18 2020 POST: Mac Loopback: Failed For Interface : TwentyFiveGigE2/2/0/38
Fri May 29 02:10:18 2020 POST: Mac Loopback: Failed For Interface : TwentyFiveGigE2/2/0/39
Fri May 29 02:10:18 2020 POST: Mac Loopback: Failed For Interface : TwentyFiveGigE2/2/0/40
Fri May 29 02:10:18 2020 POST: Module: 2 Mac Loopback: loopback Test: End, Status Failed
Exemplo de POST passado
Cat9600#show post Stored system POST messages: Switch C9606R -------------- POST: MBIST Tests : Begin POST: MBIST Tests : End, Status Passed POST: Module: 3 PHY Loopback: loopback Test: Begin POST: Module: 3 PHY Loopback: loopback Test: End, Status Passed POST: Module: 2 PHY Loopback: loopback Test: Begin POST: Module: 2 PHY Loopback: loopback Test: End, Status Passed POST: Module: 1 PHY Loopback: loopback Test: Begin POST: Module: 1 PHY Loopback: loopback Test: End, Status Passed POST: Module: 5 PHY Loopback: loopback Test: Begin POST: Module: 5 PHY Loopback: loopback Test: End, Status Passed
Cat9600#show platform Chassis type: C9606R Slot Type State Insert time (ago) --------- ------------------- --------------------- ----------------- 1 C9600-LC-24C ok 02:45:09 1/0 C9600-LC-24C ok 02:43:15 2 C9600-LC-48YL faulty 02:45:09 2/0 C9600-LC-48YL ok 02:43:14 3 C9600-SUP-1 ok 02:45:09 3/0 C9600-SUP-1 ok 02:43:14 4 C9600-SUP-1 ok 02:45:09 4/0 C9600-SUP-1 ok 02:43:14 R0 C9600-SUP-1 ok, active 02:45:09 R1 C9600-SUP-1 init, standby 02:45:09 P1 C9600-PWR-2KWAC ok 02:44:21 P2 C9600-PWR-2KWAC ok 02:44:21 P3 C9600-PWR-2KWAC ps, f0, f1, fail 02:44:21 P4 C9600-PWR-2KWAC ps, f0, f1, fail 02:44:21 P5 C9606-FAN ok 02:44:21 Slot CPLD Version Firmware Version --------- ------------------- --------------------------------------- 1 19070619 17.1.1[FC2] 2 19070619 17.1.1[FC2] 3 19041620 17.1.1[FC2] 4 19041620 17.1.1[FC2]
Testes GOLD
- Se o módulo tiver falhado no P.O.S.T ou estiver listado como 'defeituoso', o diagnóstico para obter o motivo da falha deverá ser coletado.
- Execute diagnósticos de hardware para identificar rapidamente possíveis falhas de hardware nas placas de linha ou Supervisores.
Tipos de testes de diagnóstico:
- Testes de monitoramento de integridade - Habilitados por padrão e são executados em segundo plano por alguns minutos. Esses testes não causam interrupções.
- Testes sob demanda - Executados pelo usuário com uma CLI. Alguns desses testes causam interrupções.
| Teste de diagnóstico |
O que ele está testando? Contexto? Impacto? |
| TestarGoldPktLoopback |
Esse teste é muito semelhante ao teste de Macloopback. |
| TestarOBFL |
Verifica os recursos de registro de falhas na placa. Este teste imprime uma mensagem de diagnóstico e é registrado no OBFL. |
| TestarTérmico |
Verifica se o valor de temperatura do sensor não excede o limite. É um teste que não causa interrupções e pode ser executado como um teste do monitor de integridade. |
| MonitoramentoTxPortaTeste |
Este teste monitora os contadores TX de uma interface conectada. Este teste verifica se a porta conectada pode enviar os pacotes ou não. É um teste que não causa interrupções e pode ser executado como um teste de monitoramento de integridade. |
| TestarBandejaDeVentilador |
Este teste verifica se a bandeja do ventilador foi inserida e está funcionando corretamente na placa. É um teste que não causa interrupções e pode ser executado como um teste de monitoramento de integridade. |
| TestarRegistroRascunho |
O teste Scratch Register monitora a integridade dos ASICs (application-specific integrated circuits, circuitos integrados específicos da aplicação), gravando valores nos registros e lendo novamente os valores desses registros. É um teste que não causa interrupções e pode ser executado como um teste de monitoramento de integridade. |
| McastDeVerificaçãoDeConsistênciaDeTeste |
Este teste monitora para verificar se a programação Mcast está correta. Este teste verifica com o Gerenciador de objetos de encaminhamento para identificar entradas incompletas ou configurações longas pendentes para o hardware. |
Execute um teste de diagnóstico por solicitação em um módulo.
Cat9600#diagnostic start switch module 3 test ?
Diagnostics test suite attributes:
M/C/* - Minimal bootup level test / Complete bootup level test / NA
B/* - Basic ondemand test / NA
P/V/* - Per port test / Per device test / NA
D/N/* - Disruptive test / Non-disruptive test / NA
S/* - Only applicable to standby unit / NA
X/* - Not a health monitoring test / NA
F/* - Fixed monitoring interval test / NA
E/* - Always enabled monitoring test / NA
A/I - Monitoring is active / Monitoring is inactive
Test Interval Thre-
ID Test Name Attributes day hh:mm:ss.ms shold
==== ================================== ============ =============== =====
1) TestOBFL ------------------------> *B*N*X**I not configured n/a
2) TestFantray ---------------------> *B*N****A 000 00:01:40.00 1
3) TestThermal ---------------------> *B*N****A 000 00:01:30.00 1
4) TestScratchRegister -------------> *B*N****A 000 00:01:30.00 5
5) TestConsistencyCheck ------------> *B*N****A 000 00:01:30.00 1
WORD Test ID list (e.g. 1,3-6) or Test Name
Cat9600#diagnostic start switch 1 module 3 test 2
//syslog prints upon start and finish of diagnostic test.
*Mar 24 21:48:47.968: %DIAG-6-TEST_RUNNING: switch 1 module 3: Running TestFantray{ID=2} ...
*Mar 24 21:48:47.969: %DIAG-6-TEST_OK: switch 1 module 3: TestFantray{ID=2} has completed successfully <-- Passed
| Sintoma |
Ação |
| O módulo falhou no teste de diagnóstico. |
Execute uma O.I.R. do módulo. |
Executar OIR sob demanda em um módulo
Cat9600#hw-module subslot 1/0 oir power-cycle
Proceed with power cycle of module? [confirm]
*Jun 9 20:39:14.686: %IOSXE_OIR-6-REMSPA: SPA removed from subslot 1/0, interfaces disabled
*Jun 9 20:39:14.721: %SPA_OIR-6-OFFLINECARD: SPA (C9600-LC-24C) offline in subslot 1/0
*Jun 9 20:39:16.686: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/1, changed state to down
*Jun 9 20:39:16.686: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/2, changed state to down
*Jun 9 20:39:16.687: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/3, changed state to down
*Jun 9 20:39:16.687: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/4, changed state to down
*Jun 9 20:39:16.689: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/5, changed state to down
*Jun 9 20:39:16.690: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/6, changed state to down
*Jun 9 20:39:16.690: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/7, changed state to down
*Jun 9 20:39:16.690: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/8, changed state to down
*Jun 9 20:39:16.690: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/9, changed state to down
*Jun 9 20:39:16.691: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/10, changed state to down
*Jun 9 20:39:16.691: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/11, changed state to down
*Jun 9 20:39:16.693: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/12, changed state to down
*Jun 9 20:39:16.693: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/13, changed state to down
*Jun 9 20:39:16.694: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/14, changed state to down
*Jun 9 20:39:16.694: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/15, changed state to down
*Jun 9 20:39:16.694: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/16, changed state to down
*Jun 9 20:39:16.694: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/17, changed state to down
*Jun 9 20:39:16.695: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/18, changed state to down
*Jun 9 20:39:16.695: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/19, changed state to down
*Jun 9 20:39:16.697: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/20, changed state to down
*Jun 9 20:39:16.697: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/21, changed state to down
*Jun 9 20:39:16.698: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/22, changed state to down
*Jun 9 20:39:16.698: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/23, changed state to down
*Jun 9 20:39:16.698: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/24, changed state to down
*Jun 9 20:39:16.698: %LINK-3-UPDOWN: Interface HundredGigE1/0/25, changed state to down
*Jun 9 20:39:16.699: %LINK-3-UPDOWN: Interface HundredGigE1/0/26, changed state to down
*Jun 9 20:39:16.699: %LINK-3-UPDOWN: Interface HundredGigE1/0/27, changed state to down
*Jun 9 20:39:16.701: %LINK-3-UPDOWN: Interface HundredGigE1/0/28, changed state to down
*Jun 9 20:39:16.701: %LINK-3-UPDOWN: Interface HundredGigE1/0/29, changed state to down
*Jun 9 20:39:16.702: %LINK-3-UPDOWN: Interface HundredGigE1/0/30, changed state to down
*Jun 9 20:39:16.702: %LINK-3-UPDOWN: Interface HundredGigE1/0/31, changed state to down
*Jun 9 20:39:16.702: %LINK-3-UPDOWN: Interface HundredGigE1/0/32, changed state to down
*Jun 9 20:39:16.702: %LINK-3-UPDOWN: Interface HundredGigE1/0/33, changed state to down
*Jun 9 20:39:16.703: %LINK-3-UPDOWN: Interface HundredGigE1/0/34, changed state to down
*Jun 9 20:39:16.703: %LINK-3-UPDOWN: Interface HundredGigE1/0/35, changed state to down
*Jun 9 20:39:16.704: %LINK-3-UPDOWN: Interface HundredGigE1/0/36, changed state to down
*Jun 9 20:39:16.704: %LINK-3-UPDOWN: Interface HundredGigE1/0/37, changed state to down
*Jun 9 20:39:16.705: %LINK-3-UPDOWN: Interface HundredGigE1/0/38, changed state to down
*Jun 9 20:39:16.705: %LINK-3-UPDOWN: Interface HundredGigE1/0/39, changed state to down
*Jun 9 20:39:16.713: %LINK-3-UPDOWN: Interface HundredGigE1/0/40, changed state to down
*Jun 9 20:39:16.713: %LINK-3-UPDOWN: Interface HundredGigE1/0/41, changed state to down
*Jun 9 20:39:16.713: %LINK-3-UPDOWN: Interface HundredGigE1/0/42, changed state to down
*Jun 9 20:39:16.713: %LINK-3-UPDOWN: Interface HundredGigE1/0/43, changed state to down
*Jun 9 20:39:16.713: %LINK-3-UPDOWN: Interface HundredGigE1/0/44, changed state to down
*Jun 9 20:39:16.713: %LINK-3-UPDOWN: Interface HundredGigE1/0/45, changed state to down
*Jun 9 20:39:16.713: %LINK-3-UPDOWN: Interface HundredGigE1/0/46, changed state to down
*Jun 9 20:39:16.713: %LINK-3-UPDOWN: Interface HundredGigE1/0/47, changed state to down
*Jun 9 20:39:16.713: %LINK-3-UPDOWN: Interface HundredGigE1/0/48, changed state to down
*Jun 9 20:39:44.717: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 1/0
*Jun 9 20:40:15.052: %SPA_OIR-6-ONLINECARD: SPA (C9600-LC-24C) online in subslot 1/0
*interfaces come up again*
| Sintoma |
Ação |
| O módulo ainda falha no P.O.S.T ou o módulo não está listado na saída do comando show module ou show inventory. |
|
Recoloque o módulo (Syslogs semelhantes são impressos quando o chassi reconhece o módulo e o módulo é inicializado).
*May 24 19:32:53.084: %IOSXE_OIR-6-INSCARD: Card (fp) inserted in slot F0 *May 24 19:32:53.084: %IOSXE_OIR-6-INSCARD: Card (cc) inserted in slot 1 *May 24 19:32:53.084: %IOSXE_OIR-6-ONLINECARD: Card (cc) online in slot 1 *May 24 19:32:53.151: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 1/0
Verifique se o estado de energia do módulo é aceito.
Cat9600#show power module
Power Budget Mode : Dual Sup
Power Out of In
Mod Model No State Budget Instantaneous Peak Reset Reset
--- -------------------- -------- ------ ------------- ---- ------ -----
1 C9600-LC-48YL accepted 230 0 0 230 10
2 C9600-LC-24C accepted 200 0 0 200 10
3 C9600-SUP-1 accepted 775 0 0 775 202
4 C9600-SUP-1 accepted 775 0 0 775 202
FM1 C9606-FAN accepted 450 -- -- 450 --
--- -------------------- -------- ------ ------------- ---- ------ -----
Total allocated power: 2430
Total required power: 2430
Verifique se há alguma fonte de alimentação com falha.
Cat9600#show power detail
Power Fan States
Supply Model No Type Capacity Status 1 2
------ -------------------- ---- -------- ------------ -----------
PS1 C9600-PWR-2KWAC ac 1050 W active good good
PS2 C9600-PWR-2KWAC ac 2000 W active good good
PS3 C9600-PWR-2KWAC ac n.a. fail bad bad
PS4 C9600-PWR-2KWAC ac n.a. fail bad bad
PS Current Configuration Mode : none
PS Current Operating State : none
Power supplies currently active : 2
Power supplies currently available : 4
Power Summary Maximum
(in Watts) Used Available
------------- ------ ---------
System Power 2905 2990
------------- ------ ---------
Total 2905 2990 <-- total power budget consumed vs maximum available
Power Budget Mode : Dual Sup
Power Out of In
Mod Model No State Budget Instantaneous Peak Reset Reset
--- -------------------- -------- ------ ------------- ---- ------ -----
1 C9600-LC-48TX accepted 315 0 0 315 10
2 C9600-LC-48S accepted 160 0 0 160 10
3 C9600-SUP-1 accepted 775 0 0 775 202
4 C9600-SUP-1 --- 775 -- -- 775 0
5 C9600-LC-48YL accepted 230 0 0 230 10
6 C9600-LC-24C accepted 200 0 0 200 10
FM1 C9606-FAN accepted 450 -- -- 450 --
--- -------------------- -------- ------ ------------- ---- ------ -----
Total allocated power: 2905
Total required power: 2905
Incompatibilidade de software e firmware
- Os supervisores em diferentes versões de software ou firmware não conseguem sincronizar as funções Ativo/Em espera de alta disponibilidade.
- As placas de linha em uma versão de firmware mais recente em comparação a uma versão de firmware do Supervisor podem não ser inicializadas.
- Instruções incluídas na seção "Atualizando o software do switch" nas Notas de versão de todos os principais treinamentos de software, como 16.12.X, 17.3.X e 17.6.X
- Atualize manualmente o firmware/bootldr do Supervisor.
Observação: revise as Release Notes dos Catalyst 9600 Series Switches Cisco IOS XE Amsterdam 17.3.X para obter informações mais detalhadas sobre como atualizar manualmente o firmware/carregador de inicialização do Supervisor.
Cat9600#show firmware version all
Current Bundled
Slot Device Name / Model Firmware Version Firmware Version Mismatch
----- ----------------------------- --------------------- ------------------- ---------
3 Supervisor Rommon (Active) 17.3.1r[FC2] N/A N/A <-- Firmware versions are the same
4 Supervisor Rommon (Standby) 17.3.1r[FC2] N/A N/A <-- Firmware versions are the same
- Eth Lan Spi 0x800005d3 N/A N/A
PS5 Fantray 18101008 N/A N/A
3 Supervisor CPLD
IO FPGA 19041620 19041620 No
Flash FPGA 190308b9 190308b9 No
4 Supervisor CPLD
IO FPGA 19041620 19041620 No
Flash FPGA 190308b9 190308b9 No
1 Line Card / C9600-LC-24C
IO FPGA 19070619 19070619 No
PMFPGA 122515 N/A N/A
Phy Firmware 1.56.1772 1.56.2270 Yes
2 Line Card / C9600-LC-48YL
IO FPGA 19070619 19070619 No
PMFPGA 122515 N/A N/A
Phy Firmware 1.56.1772 1.56.2270 Yes
5 Line Card / C9600-LC-48YL
IO FPGA 19070619 19070619 No
PMFPGA 122515 N/A N/A
Phy Firmware 1.56.1772 1.56.2270 Yes
6 Line Card / C9600-LC-24C
IO FPGA 19070619 19070619 No
PMFPGA 122515 N/A N/A
Phy Firmware 1.56.1772 1.56.2270 Yes
Slot Device Name / Model Firmware Version
--------- --------------------------------------- -----------------------------
PS1 Power Supply (PS PRI, PS_SEC, PS_I2C) (N/A, N/A, N/A)
PS2 Power Supply (PS PRI, PS_SEC, PS_I2C) (N/A, N/A, N/A)
PS3 Power Supply (PS PRI, PS_SEC, PS_I2C) (N/A, N/A, N/A)
PS4 Power Supply (PS PRI, PS_SEC, PS_I2C) (61.08.03, 61.02.0, N/A)
Troubleshooting Adicional
Observação: o status de autenticação do hardware é executado somente no recarregamento do switch. Ele não é executado após a recolocação física da placa de linha no mesmo slot ou em um slot diferente, e isso não indica necessariamente um problema.
Se o status de autenticação NÃO for aprovado para uma placa de linha presente, execute estas etapas sugeridas:
- Colete o arquivo de rastreamento, revise os arquivos IOSRP, CMCC, platform_mgr e IOMD para obter informações relevantes sobre esse tipo de problema.
- O OIR físico do componente afetado OU a recarga do switch pode ser tentado para ver se ele se recupera.
- Se o problema persistir, abra um caso de TAC.
Cat9600#show platform hardware authentication status
Fan Tray Authentication: pass
Line Card:1 Authentication: pass
Line Card:2 Authentication: pass
SUP0 Authentication: pass
SUP1 Authentication: pass
Line Card:5 Authentication: Not Available
Line Card:6 Authentication: Not Available
Cat9600#show hw-module subslot 1/0 oir internal
IOMD for supervisor slot does not appear
WARNING: This command is not intended for production use
and should only be used under the supervision of
Cisco Systems technical support personnel.
sm(spa_oir_tsm subslot 1/0 TSM), running yes, state ready
Admin Status: admin enabled, Operational Status: ok(1)
Last reset Reason: power up
TSM Context:
configured_spa_type 0xD9A <-- IDPROM is accessible
soft remove fail code 0x0(none)
last_fail_code 0x0(none)
timed_fail_count 0, failed_spa_type 0x0
flags 0x10)
Subslot:
spa type 0xD9A, active spa type 0xD9A
subslot flags 0x0, plugin flags 0x0
TSM Parameters:
wait_psm_ready_timeout 540000 ms, init_timeout 300000 ms
remove_timeout 120000 ms, recovery_delay 5000 ms
fail_time_period 1200000 ms, max_fail_count 5
does not support pre-configuration
Cat9600# show platform software iomd redundancy
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
Local RF state = ACTIVE
Peer RF state = STANDBY HOT
slot PSM STATE SPA INTF HA_STATE HA_ACTIVE
1 ready started ready 00:05:54
2 ready idle <-- potential issue
3 ready started ready 00:05:37 ***active RP
4 ready started ready 00:05:37
Cat9600#show idprom module 1 eeprom detail
Slot 1 EEPROM data:
EEPROM version : 4
Compatible Type : 0xFF
Controller Type : 3482
Hardware Revision : 1.0
PCB Part Number : 73-19545-02
Board Revision : A0
Deviation Number : 0
Fab Version : 02
PCB Serial Number : CAT2313L2VP
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Top Assy. Part Number : 068-102161-01
Top Assy. Revision : A0
CLEI Code : COUIBGRCAA
Product Identifier (PID) : C9600-LC-24C
Version Identifier (VID) : V01
Base MAC Address : DC 8C 37 A0 C8 80
MAC Address block size : 128
Environment Monitor Data : 06 00 00 00 0C 80 C8 00
A6
Environment Monitor Data : 00 06 00 FA
Manufacturing Test Data : 00 00 00 00 00 00 00 00
Field Diagnostics Data : 00 00 00 00 00 00 00 00
Platform features : 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00
Environment Monitor Data :
Description : InltFrnt
Shutdown threshold : 060
Critical threshold : 055
Major threshold : 050
Minor threshold : 045
Environment Monitor Data :
Description : InltRear
Shutdown threshold : 060
Critical threshold : 055
Major threshold : 050
Minor threshold : 045
Environment Monitor Data :
Description : OtltFrnt
Shutdown threshold : 090
Critical threshold : 085
Major threshold : 080
Minor threshold : 075
Environment Monitor Data :
Description : OtltRear
Shutdown threshold : 090
Critical threshold : 085
Major threshold : 080
Minor threshold : 075
Use o comando lc-portmap para obter informações sobre as interfaces da placa de linha que mapeiam para o ASIC/Núcleo no Supervisor.
Cat9600#show platform hardware iomd 1/0 lc-portmap detail
IOMD SUMMARY
==============
spa_type: 0xd9a
my_slot: 1
active-slot: 0
is_active: 1
bulk_sync_done: 1
bulk_sync_in_progress: 0
bulk_sync_received: 0
is_plugin_start_done: 1
Num_ports: 48 num_UDAP 3s: 3
PSM SUMMARY
===============
PSM state: ready
ha_state:
is_spa_ok: 0
is_power_ok: 0
psm_flags: 0x0
bay_flags: 0x0
plugin_flags: 0x0
Port fp asic core mac cntx asic speed xcvr- xcvr- run- phy- i2c- xcvr- if- SerTune- False- Rcvr- Serdes-
port pres type speed num ctrl sm state Status LinkUp idle set
================================================================================================================================
0 1 0 0 0 0 0 40G no 0 unk 0 0 0 0 NOTS no 0 0 1
1 2 0 0 2 1 8 40G no 0 unk 0 0 0 0 NOTS no 0 2 3
2 3 0 0 16 0 16 40G no 0 unk 1 0 0 0 NOTS no 0 16 17
3 4 0 0 18 1 24 40G no 0 unk 1 0 0 0 NOTS no 0 18 19
4 5 0 1 14 1 8 40G no 0 unk 2 0 0 0 NOTS no 0 14 15
5 6 0 1 12 0 0 40G no 0 unk 2 0 0 0 NOTS no 0 12 13
6 7 0 1 30 1 24 40G no 0 unk 3 0 0 0 NOTS no 0 30 31
7 8 0 1 28 0 16 40G no 0 unk 3 0 0 0 NOTS no 0 28 29
8 9 1 0 0 0 0 40G no 0 unk 4 0 0 0 NOTS no 0 0 1
9 10 1 0 2 1 8 40G no 0 unk 4 0 0 0 NOTS no 0 2 3
10 11 1 0 16 0 16 40G no 0 unk 5 0 0 0 NOTS no 0 16 17
11 12 1 0 18 1 24 40G no 0 unk 5 0 0 0 NOTS no 0 18 19
12 13 1 1 14 1 8 40G no 0 unk 6 0 0 0 NOTS no 0 14 15
13 14 1 1 12 0 0 40G no 0 unk 6 0 0 0 NOTS no 0 12 13
14 15 1 1 30 1 24 40G no 0 unk 7 0 0 0 NOTS no 0 30 31
15 16 1 1 28 0 16 40G no 0 unk 7 0 0 0 NOTS no 0 28 29
16 17 2 0 0 0 0 40G no 0 unk 8 1 0 0 NOTS no 0 0 1
17 18 2 0 2 1 8 40G no 0 unk 8 1 0 0 NOTS no 0 2 3
18 19 2 0 16 0 16 40G no 0 unk 9 1 0 0 NOTS no 0 16 17
19 20 2 0 18 1 24 40G no 0 unk 9 1 0 0 NOTS no 0 18 19
20 21 2 1 14 1 8 40G no 0 unk 10 1 0 0 NOTS no 0 14 15
21 22 2 1 12 0 0 40G no 0 unk 10 1 0 0 NOTS no 0 12 13
22 23 2 1 30 1 24 40G no 0 unk 11 1 0 0 NOTS no 0 30 31
23 24 2 1 28 0 16 40G no 0 unk 11 1 0 0 NOTS no 0 28 29
24 25 0 0 0 0 0 100G no 0 unk 0 0 0 0 NOTS no 0 0 1 2 3
25 26 0 0 0 0 0 100G no 0 unk 0 0 0 0 NOTS no 0 0 1 2 3
26 27 0 0 16 0 16 100G no 0 unk 1 0 0 0 NOTS no 0 16 17 18 19
27 28 0 0 16 0 16 100G no 0 unk 1 0 0 0 NOTS no 0 16 17 18 19
28 29 0 1 12 0 0 100G no 0 unk 2 0 0 0 NOTS no 0 12 13 14 15
29 30 0 1 12 0 0 100G no 0 unk 2 0 0 0 NOTS no 0 12 13 14 15
30 31 0 1 28 0 16 100G no 0 unk 3 0 0 0 NOTS no 0 28 29 30 31
31 32 0 1 28 0 16 100G no 0 unk 3 0 0 0 NOTS no 0 28 29 30 31
32 33 1 0 0 0 0 100G no 0 unk 4 0 0 0 NOTS no 0 0 1 2 3
33 34 1 0 0 0 0 100G no 0 unk 4 0 0 0 NOTS no 0 0 1 2 3
34 35 1 0 16 0 16 100G no 0 unk 5 0 0 0 NOTS no 0 16 17 18 19
35 36 1 0 16 0 16 100G no 0 unk 5 0 0 0 NOTS no 0 16 17 18 19
36 37 1 1 12 0 0 100G no 0 unk 6 0 0 0 NOTS no 0 12 13 14 15
37 38 1 1 12 0 0 100G no 0 unk 6 0 0 0 NOTS no 0 12 13 14 15
38 39 1 1 28 0 16 100G no 0 unk 7 0 0 0 NOTS no 0 28 29 30 31
39 40 1 1 28 0 16 100G no 0 unk 7 0 0 0 NOTS no 0 28 29 30 31
40 41 2 0 0 0 0 100G no 0 unk 8 1 0 0 NOTS no 0 0 1 2 3
41 42 2 0 0 0 0 100G no 0 unk 8 1 0 0 NOTS no 0 0 1 2 3
42 43 2 0 16 0 16 100G no 0 unk 9 1 0 0 NOTS no 0 16 17 18 19
43 44 2 0 16 0 16 100G no 0 unk 9 1 0 0 NOTS no 0 16 17 18 19
44 45 2 1 12 0 0 100G no 0 unk 10 1 0 0 NOTS no 0 12 13 14 15
45 46 2 1 12 0 0 100G no 0 unk 10 1 0 0 NOTS no 0 12 13 14 15
46 47 2 1 28 0 16 100G no 0 unk 11 1 0 0 NOTS no 0 28 29 30 31
47 48 2 1 28 0 16 100G no 0 unk 11 1 0 0 NOTS no 0 28 29 30 31
Cat9600#show platform software fed [active | standby] ifm mappings Interface IF_ID Inst Asic Core Port SubPort Mac Cntx LPN GPN Type Active TwentyFiveGigE1/0/1 0x9 0 0 0 0 0 0 0 1 101 NIF Y TwentyFiveGigE1/0/2 0xa 0 0 0 4 0 1 1 2 102 NIF Y TwentyFiveGigE1/0/3 0xb 0 0 0 8 0 2 2 3 103 NIF Y TwentyFiveGigE1/0/4 0xc 0 0 0 12 0 3 3 4 104 NIF Y TwentyFiveGigE1/0/5 0xd 0 0 0 16 0 16 0 5 105 NIF Y TwentyFiveGigE1/0/6 0xe 0 0 0 20 0 17 1 6 106 NIF Y TwentyFiveGigE1/0/7 0xf 0 0 0 24 0 18 2 7 107 NIF Y TwentyFiveGigE1/0/8 0x10 0 0 0 28 0 19 3 8 108 NIF Y TwentyFiveGigE1/0/9 0x11 1 0 1 12 0 15 3 9 109 NIF Y TwentyFiveGigE1/0/10 0x12 1 0 1 8 0 14 2 10 110 NIF Y TwentyFiveGigE1/0/11 0x13 1 0 1 4 0 13 1 11 111 NIF Y TwentyFiveGigE1/0/12 0x14 1 0 1 0 0 12 0 12 112 NIF Y TwentyFiveGigE1/0/13 0x15 1 0 1 28 0 31 3 13 113 NIF Y TwentyFiveGigE1/0/14 0x16 1 0 1 24 0 30 2 14 114 NIF Y TwentyFiveGigE1/0/15 0x17 1 0 1 20 0 29 1 15 115 NIF Y TwentyFiveGigE1/0/16 0x18 1 0 1 16 0 28 0 16 116 NIF Y TwentyFiveGigE1/0/17 0x19 2 1 0 0 0 0 0 17 117 NIF Y TwentyFiveGigE1/0/18 0x1a 2 1 0 4 0 1 1 18 118 NIF Y TwentyFiveGigE1/0/19 0x1b 2 1 0 8 0 2 2 19 119 NIF Y TwentyFiveGigE1/0/20 0x1c 2 1 0 12 0 3 3 20 120 NIF Y TwentyFiveGigE1/0/21 0x1d 2 1 0 16 0 16 0 21 121 NIF Y TwentyFiveGigE1/0/22 0x1e 2 1 0 20 0 17 1 22 122 NIF Y TwentyFiveGigE1/0/23 0x1f 2 1 0 24 0 18 2 23 123 NIF Y TwentyFiveGigE1/0/24 0x20 2 1 0 28 0 19 3 24 124 NIF Y TwentyFiveGigE1/0/25 0x21 3 1 1 12 0 15 3 25 125 NIF Y TwentyFiveGigE1/0/26 0x22 3 1 1 8 0 14 2 26 126 NIF Y TwentyFiveGigE1/0/27 0x23 3 1 1 4 0 13 1 27 127 NIF Y TwentyFiveGigE1/0/28 0x24 3 1 1 0 0 12 0 28 128 NIF Y TwentyFiveGigE1/0/29 0x25 3 1 1 28 0 31 3 29 129 NIF Y TwentyFiveGigE1/0/30 0x26 3 1 1 24 0 30 2 30 130 NIF Y TwentyFiveGigE1/0/31 0x27 3 1 1 20 0 29 1 31 131 NIF Y TwentyFiveGigE1/0/32 0x28 3 1 1 16 0 28 0 32 132 NIF Y TwentyFiveGigE1/0/33 0x29 4 2 0 0 0 0 0 33 133 NIF Y TwentyFiveGigE1/0/34 0x2a 4 2 0 4 0 1 1 34 134 NIF Y TwentyFiveGigE1/0/35 0x2b 4 2 0 8 0 2 2 35 135 NIF Y TwentyFiveGigE1/0/36 0x2c 4 2 0 12 0 3 3 36 136 NIF Y TwentyFiveGigE1/0/37 0x2d 4 2 0 16 0 16 0 37 137 NIF Y TwentyFiveGigE1/0/38 0x2e 4 2 0 20 0 17 1 38 138 NIF Y TwentyFiveGigE1/0/39 0x2f 4 2 0 24 0 18 2 39 139 NIF Y TwentyFiveGigE1/0/40 0x30 4 2 0 28 0 19 3 40 140 NIF Y TwentyFiveGigE1/0/41 0x31 5 2 1 12 0 15 3 41 141 NIF Y TwentyFiveGigE1/0/42 0x32 5 2 1 8 0 14 2 42 142 NIF Y TwentyFiveGigE1/0/43 0x33 5 2 1 4 0 13 1 43 143 NIF Y TwentyFiveGigE1/0/44 0x34 5 2 1 0 0 12 0 44 144 NIF Y TwentyFiveGigE1/0/45 0x35 5 2 1 28 0 31 3 45 145 NIF Y TwentyFiveGigE1/0/46 0x36 5 2 1 24 0 30 2 46 146 NIF Y TwentyFiveGigE1/0/47 0x37 5 2 1 20 0 29 1 47 147 NIF Y TwentyFiveGigE1/0/48 0x38 5 2 1 16 0 28 0 48 148 NIF Y TwentyFiveGigE2/0/2 0x3a 0 0 0 9 0 9 9 2 202 NIF Y TwentyFiveGigE2/0/3 0x3b 0 0 0 10 0 10 10 3 203 NIF Y TwentyFiveGigE2/0/4 0x3c 0 0 0 11 0 11 11 4 204 NIF Y TwentyFiveGigE2/0/5 0x3d 0 0 0 18 0 24 8 5 205 NIF Y TwentyFiveGigE2/0/6 0x3e 0 0 0 25 0 25 9 6 206 NIF Y TwentyFiveGigE2/0/7 0x3f 0 0 0 26 0 26 10 7 207 NIF Y TwentyFiveGigE2/0/8 0x40 0 0 0 27 0 27 11 8 208 NIF Y TwentyFiveGigE2/0/9 0x41 1 0 1 7 0 7 7 9 209 NIF Y TwentyFiveGigE2/0/10 0x42 1 0 1 6 0 6 6 10 210 NIF Y TwentyFiveGigE2/0/11 0x43 1 0 1 5 0 5 5 11 211 NIF Y TwentyFiveGigE2/0/12 0x44 1 0 1 1 0 4 4 12 212 NIF Y TwentyFiveGigE2/0/13 0x45 1 0 1 23 0 23 7 13 213 NIF Y TwentyFiveGigE2/0/14 0x46 1 0 1 22 0 22 6 14 214 NIF Y TwentyFiveGigE2/0/15 0x47 1 0 1 21 0 21 5 15 215 NIF Y TwentyFiveGigE2/0/16 0x48 1 0 1 17 0 20 4 16 216 NIF Y TwentyFiveGigE2/0/17 0x49 2 1 0 2 0 8 8 17 217 NIF Y TwentyFiveGigE2/0/18 0x4a 2 1 0 9 0 9 9 18 218 NIF Y TwentyFiveGigE2/0/19 0x4b 2 1 0 10 0 10 10 19 219 NIF Y TwentyFiveGigE2/0/20 0x4c 2 1 0 11 0 11 11 20 220 NIF Y TwentyFiveGigE2/0/21 0x4d 2 1 0 18 0 24 8 21 221 NIF Y TwentyFiveGigE2/0/22 0x4e 2 1 0 25 0 25 9 22 222 NIF Y TwentyFiveGigE2/0/23 0x4f 2 1 0 26 0 26 10 23 223 NIF Y TwentyFiveGigE2/0/24 0x50 2 1 0 27 0 27 11 24 224 NIF Y TwentyFiveGigE2/0/25 0x51 3 1 1 7 0 7 7 25 225 NIF Y TwentyFiveGigE2/0/26 0x52 3 1 1 6 0 6 6 26 226 NIF Y TwentyFiveGigE2/0/27 0x53 3 1 1 5 0 5 5 27 227 NIF Y TwentyFiveGigE2/0/28 0x54 3 1 1 1 0 4 4 28 228 NIF Y TwentyFiveGigE2/0/29 0x55 3 1 1 23 0 23 7 29 229 NIF Y TwentyFiveGigE2/0/30 0x56 3 1 1 22 0 22 6 30 230 NIF Y TwentyFiveGigE2/0/31 0x57 3 1 1 21 0 21 5 31 231 NIF Y TwentyFiveGigE2/0/32 0x58 3 1 1 17 0 20 4 32 232 NIF Y TwentyFiveGigE2/0/33 0x59 4 2 0 2 0 8 8 33 233 NIF Y TwentyFiveGigE2/0/34 0x5a 4 2 0 9 0 9 9 34 234 NIF Y TwentyFiveGigE2/0/35 0x5b 4 2 0 10 0 10 10 35 235 NIF Y TwentyFiveGigE2/0/36 0x5c 4 2 0 11 0 11 11 36 236 NIF Y TwentyFiveGigE2/0/37 0x5d 4 2 0 18 0 24 8 37 237 NIF Y TwentyFiveGigE2/0/38 0x5e 4 2 0 25 0 25 9 38 238 NIF Y TwentyFiveGigE2/0/39 0x5f 4 2 0 26 0 26 10 39 239 NIF Y TwentyFiveGigE2/0/40 0x60 4 2 0 27 0 27 11 40 240 NIF Y TwentyFiveGigE2/0/41 0x61 5 2 1 7 0 7 7 41 241 NIF Y TwentyFiveGigE2/0/42 0x62 5 2 1 6 0 6 6 42 242 NIF Y TwentyFiveGigE2/0/43 0x63 5 2 1 5 0 5 5 43 243 NIF Y TwentyFiveGigE2/0/44 0x64 5 2 1 1 0 4 4 44 244 NIF Y TwentyFiveGigE2/0/45 0x65 5 2 1 23 0 23 7 45 245 NIF Y TwentyFiveGigE2/0/46 0x66 5 2 1 22 0 22 6 46 246 NIF Y TwentyFiveGigE2/0/47 0x67 5 2 1 21 0 21 5 47 247 NIF Y TwentyFiveGigE2/0/48 0x68 5 2 1 17 0 20 4 48 248 NIF Y
Comandos a serem coletados para TAC
Os problemas de hardware e os comandos de validação mais comuns são abordados neste guia, com as etapas de correção apropriadas. No entanto, caso este guia não resolva o problema, colete a lista de comandos mostrada e anexe-a à sua solicitação de serviço do TAC.
show tech-support show post show platform hardware authentication status show platform hardware chassis fantray detail show platform software iomd redundancy
request platform software trace archive
service internal (for the standby command 'service internal' needs to be enabled first)
request platform software trace slot rp standby archive target stby-bootflash
Histórico de revisões
| Revisão | Data de publicação | Comentários |
|---|---|---|
1.0 |
05-Jul-2023 |
Versão inicial |
FeedbackContate a Cisco
- Abrir um caso de suporte
- (É necessário um Contrato de Serviço da Cisco)