Configurando o host iSCSI Solaris para MDS/IPS-8

Opções de download

  • PDF     (375.3 KB)
    Ver no Adobe Reader em vários dispositivos
  • ePub     (248.5 KB)
    Ver em vários aplicativos no iPhone, iPad, Android, Sony Reader ou Windows Phone
  • Mobi (Kindle)     (276.3 KB)
    Ver no dispositivo Kindle ou no aplicativo Kindle em vários dispositivos
Atualizado:8 de Outubro de 2018
ID do documento:44860

Linguagem imparcial

O conjunto de documentação deste produto faz o possível para usar uma linguagem imparcial. Para os fins deste conjunto de documentação, a imparcialidade é definida como uma linguagem que não implica em discriminação baseada em idade, deficiência, gênero, identidade racial, identidade étnica, orientação sexual, status socioeconômico e interseccionalidade. Pode haver exceções na documentação devido à linguagem codificada nas interfaces de usuário do software do produto, linguagem usada com base na documentação de RFP ou linguagem usada por um produto de terceiros referenciado. Saiba mais sobre como a Cisco está usando a linguagem inclusiva.

Sobre esta tradução

A Cisco traduziu este documento com a ajuda de tecnologias de tradução automática e humana para oferecer conteúdo de suporte aos seus usuários no seu próprio idioma, independentemente da localização. Observe que mesmo a melhor tradução automática não será tão precisa quanto as realizadas por um tradutor profissional. A Cisco Systems, Inc. não se responsabiliza pela precisão destas traduções e recomenda que o documento original em inglês (link fornecido) seja sempre consultado.

Introduction

Os drivers da Cisco Small Computer Systems Interface over IP (iSCSI) são um componente chave da solução iSCSI. Esses drivers da iSCSI residem no servidor, onde eles:

  • Interceptar comandos iSCSI.

  • Encapsular os comandos em pacotes IP.

  • Redirecione os comandos para o Cisco SN 5420, Cisco SN 5428, Cisco SN 5428-2 ou Cisco MDS/IPS-8.

Este documento fornece exemplos de configurações para o host iSCSI Solaris para o Cisco MDS/IPS-8.

Prerequisites

Requirements

Certifique-se de atender a estes requisitos antes de tentar esta configuração:

  • Instale o driver iSCSI compatível com a versão Solaris e crie a configuração iSCSI no Cisco MDS 9000. Consulte Cisco iSCSI Drivers (somente clientes registrados) para obter a versão mais recente do driver (solaris-iscsi-3.3.5.tar.Z). Um arquivo README.txt está incluído no arquivo ZIP (TAR) do driver. O arquivo README.txt contém:

    • Informações do contrato de licença

    • Instruções de instalação e configuração do driver

    • Uma visão geral técnica da arquitetura do driver

  • Consulte as seções Requisitos do sistema nas Notas de versão do driver iSCSI da Cisco para Sun Solaris para o sistema operacional (SO) e os requisitos de patch.

  • O driver iSCSI da Cisco para Sun Solaris é executado somente em máquinas SPARC. O driver não funciona com nenhum outro tipo de processador (por exemplo, x86).

Componentes Utilizados

As informações neste documento são baseadas nestas versões de software e hardware:

  • SunOS 5.9, SPARC Ultra-4 E450

    #uname -a

SunOS baboon 5.9 Generic sun4u sparc SUNW,Ultra-4

  • Driver iSCSI Cisco 3.3.3 para Solaris

    #pkginfo -l CSCOiscsi

   PKGINST:  CSCOiscsi
      NAME:  Cisco iSCSI device driver
  CATEGORY:  system
      ARCH:  sparc
   VERSION:  3.3.3
   BASEDIR:  /opt/CSCOiscsi
    VENDOR:  Cisco Systems, Inc.
      DESC:  Cisco iSCSI device driver 3.3.3
    PSTAMP:  solaris-920030807170521
  INSTDATE:  Aug 25 2003 23:41
   HOTLINE:  For contracted support, 1-800-553-2447,
             Cisco Technical Assistance Center (TAC)
     EMAIL:  For online help, go to http://www.cisco.com/
    STATUS:  completely installed
     FILES:       74 installed pathnames
                  16 shared pathnames
                  29 directories
                  32 executables
                2182 blocks used (approx)

#iscsi-ls -v

iSCSI driver version: 3.3.3

  • Cisco MDS 9216 com versão de software 1.1.2

    canterbury#show module

Mod  Ports  Module-Type                     Model              Status
---  -----  ------------------------------- ------------------ ------------
1    16     1/2 Gbps FC/Supervisor          DS-X9216-K9-SUP    active *
2    8      IP Storage Module               DS-X9308-SMIP      ok
Mod  Sw           Hw      World-Wide-Name(s) (WWN)
---  -----------  ------  --------------------------------------------------
1    1.1(2)       1.0     20:01:00:0c:30:6c:24:40 to 20:10:00:0c:30:6c:24:40
2    1.1(2)       0.3     20:41:00:0c:30:6c:24:40 to 20:48:00:0c:30:6c:24:40

Mod  MAC-Address(es)                         Serial-Num
---  --------------------------------------  ----------
1    00-0b-be-f8-7f-08 to 00-0b-be-f8-7f-0c  JAB070804QK
2    00-05-30-00-ad-e2 to 00-05-30-00-ad-ee  JAB070806SB

* this terminal session

canterbury#show version

Cisco Storage Area Networking Operating System (SAN-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2003 by Cisco Systems, Inc. All rights reserved.
The copyright for certain works contained herein are owned by
Andiamo Systems, Inc. and/or other third parties and are used and
distributed under license.

Software
  BIOS:      version 1.0.7
  loader:    version 1.0(3a)
  kickstart: version 1.1(2)
  system:    version 1.1(2)

  BIOS compile time:       03/20/03
  kickstart image file is: bootflash:/k112
  kickstart compile time:  7/13/2003 20:00:00
  system image file is:    bootflash:/s112
  system compile time:     7/13/2003 20:00:00

Hardware
  RAM 963112 kB

  bootflash: 500736 blocks (block size 512b)
  slot0:          0 blocks (block size 512b)

  canterbury uptime is 16 days 20 hours 51 minute(s) 36 second(s)

  Last reset at 684726 usecs after Mon Aug 11 13:53:17 2003
    Reason: Reset Requested by CLI command reload
    System version: 1.1(2)

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Conventions

Consulte as Convenções de Dicas Técnicas da Cisco para obter mais informações sobre convenções de documentos.

Informações de Apoio

O módulo de armazenamento IP fornece aos hosts IP acesso a dispositivos de armazenamento Fibre Channel (FC). O módulo de armazenamento IP é um DS-X9308-SMIP que fornece roteamento iSCSI transparente. Os hosts IP que usam o protocolo iSCSI podem acessar de forma transparente destinos iSCSI (FC Protocol [FCP]) na rede FC. O host IP envia comandos iSCSI encapsulados em PDUs (Protocol Data Units, unidades de dados de protocolo) iSCSI para uma porta de armazenamento IP Cisco MDS 9000 através de uma conexão TCP/IP. As interfaces Gigabit Ethernet (GE) configuradas adequadamente no módulo de armazenamento IP fornecem conectividade. O módulo de armazenamento IP:

  • Permite criar destinos iSCSI virtuais e mapeá-los para destinos FC físicos disponíveis na SAN FC

  • Apresenta os destinos FC aos hosts IP como se os destinos físicos estivessem conectados localmente à rede IP

Cada host iSCSI que requer acesso ao armazenamento através do módulo de armazenamento IP deve ter um driver iSCSI compatível instalado. O driver iSCSI permite que um host iSCSI transporte solicitações e respostas iSCSI através de uma rede IP com o protocolo iSCSI. Da perspectiva de um SO host, o driver iSCSI parece ser um driver de transporte iSCSI semelhante a um driver FC para um canal periférico no host. Cada host IP aparece como um host FC da perspectiva do dispositivo de armazenamento.

Conclua estes passos para rotear o iSCSI do host IP para o dispositivo de armazenamento FC:

  • Transportar solicitações e respostas iSCSI em uma rede IP entre hosts e o módulo de armazenamento IP.

  • Use o módulo de armazenamento IP para rotear solicitações e respostas iSCSI entre hosts em uma rede IP e o dispositivo de armazenamento FC (converta iSCSI em FCP e vice-versa).

  • Transporta solicitações ou respostas de FCP entre o módulo de armazenamento IP e os dispositivos de armazenamento FC.

O módulo de armazenamento IP não importa os destinos FC para iSCSI por padrão. Você deve configurar o mapeamento dinâmico ou estático para que o módulo de armazenamento IP torne os destinos FC disponíveis para iniciadores iSCSI. Os destinos FC mapeados estaticamente têm um nome configurado quando ambos estão configurados. Essa configuração fornece exemplos de mapeamento estático.

Cada vez que o host iSCSI se conecta ao módulo de armazenamento IP com mapeamento dinâmico:

  • Uma nova porta FC N é criada.

  • Os nomes do mundo inteiro do nó (nWWNs) e os nomes do mundo inteiro da porta (pWWNs) alocados para essa porta N podem ser diferentes.

Use o método de mapeamento estático se você precisar obter os mesmos nWWNs e pWWNs para o host iSCSI toda vez que ele se conectar ao módulo de armazenamento IP. Você pode usar o mapeamento estático no módulo de armazenamento IP para acessar matrizes de armazenamento FC inteligentes que tenham:

  • Controle de acesso

  • Mapeamento de número de unidade lógica (LUN) e configuração de máscara que são baseados em pWWNs ou nWWNs do iniciador

Especifique estes itens para controlar o acesso a cada destino iSCSI mapeado estaticamente:

  • Uma lista de portas de armazenamento IP nas quais são anunciadas

  • Uma lista de nomes de nós do iniciador iSCSI que têm acesso permitido

O controle de acesso baseado em zoneamento FC e o controle de acesso baseado em iSCSI são os dois mecanismos pelos quais o controle de acesso pode ser fornecido para iSCSI. Você pode usar ambos os métodos simultaneamente. O zoneamento padrão foi permitido para uma rede de área de armazenamento virtual (VSAN) específica nesta configuração. Os módulos de armazenamento IP usam listas de controle de acesso baseadas em nome de nó iSCSI e baseadas em zoneamento FC para aplicar o controle de acesso durante a descoberta iSCSI e a criação de sessões iSCSI.

O iniciador iSCSI pode ser definido estaticamente por endereço IP ou por nome qualificado (IQN) iSCSI. Uma opção de iniciador de proxy permite a criação dinâmica de iniciadores iSCSI em SAN-IOS 1.3 para os switches Cisco MDS.

A descoberta de iSCSI ocorre quando um host iSCSI cria uma sessão de descoberta iSCSI e consulta todos os destinos iSCSI. O módulo de armazenamento IP retorna apenas a lista de destinos iSCSI que as políticas de controle de acesso permitem que o host iSCSI acesse.

A criação de sessão iSCSI ocorre quando um host IP inicia uma sessão iSCSI. O módulo de armazenamento IP verifica:

  • Se o destino iSCSI especificado (na solicitação de login da sessão) for um destino mapeado estático

  • Que o nome do nó iSCSI do host IP tem permissão para acessar o destino

O login será rejeitado se o host IP não tiver acesso.

O módulo de armazenamento IP então:

  • Cria uma porta N virtual FC (a porta N já pode existir) para este host IP

  • Faz uma consulta de servidor de nome FC para o ID de Fibre Channel (FCID) do pWWN de destino FC acessado pelo host IP

O módulo de armazenamento IP usa o pWWN da porta N virtual do host IP como o solicitante da consulta do servidor de nome. Assim, o servidor de nomes faz uma consulta imposta por zona para o pWWN e responde à consulta. A sessão iSCSI será aceita se o servidor de nome retornar o FCID. Caso contrário, a solicitação de login será rejeitada.

Configurar

Nesta seção, você encontrará informações para configurar os recursos descritos neste documento.

Nota:Use a Command Lookup Tool (somente clientes registrados) para obter mais informações sobre os comandos usados neste documento.

Diagrama de Rede

Este documento utiliza a seguinte configuração de rede:

sn5428_solaris_1.gif

Configurações

Este documento utiliza as seguintes configurações:

babuíno (SunOS 5.9, SPARC E450)
Modifique estes arquivos no host Solaris:
  • /etc/iscsi.conf
  • /etc/iscsi.bindings
  • /kernel/drv/sd.conf
Este é um exemplo de saída de configuração: 
bash-2.05#cat /etc/iscsi.conf

# iSCSI configuration file - see iscsi.conf(4)

# DiscoveryAddress Settings
# -------------------------
# Add "DiscoveryAddress=xxx" entries for each iSCSI router instance.
# The driver will attempt to discover iSCSI targets at that address
# and make as many targets as possible available for use.
# 'xxx' can be an IP address or a hostname.  A TCP port number can be
# specified by appending a colon and the port number to the address.
# All entries have to start in column one and must not contain any
# whitespace.
#
# Example:
#
# DiscoveryAddress=scsirouter1
 DiscoveryAddress=10.48.69.199

!--- Configure the IP address of the GE interface that accepts iSCSI !--- requests from your host.

# The DiscoveryAddress Settings can take following entry.
#
# 1) Authentication Settings
# 2) ConnectionTimeout Settings

!--- Other required driver parameters can be changed in the iscsi.conf file. !--- Output is suppressed.

bash-2.05#cat /etc/iscsi.bindings

# iSCSI bindings, file format version 1.0.
# NOTE: this file is automatically maintained by the iSCSI daemon.
# You should not need to edit this file under most circumstances.
# If iSCSI targets in this file have been permanently deleted, you
# may wish to delete the bindings for the deleted targets.
#
# Format:
# bus   target  iSCSI
# id    id      TargetName
#
0       0       san-fc-jbod-1
0       1       clariion
0       2       clariion-lun-3-4-5

!--- The iSCSI driver discovery daemon process looks up each discovered target !--- in the /etc/iscsi.bindings file. !--- The corresponding iSCSI target ID is assigned to the target if an entry exists in the file for the target. !--- The smallest available iSCSI target ID !--- is assigned if no entry exists for the target, and an entry is written to the /etc/iscsi.bindings file for !--- this target. !--- Note that the /etc/iscsi.bindings file permanently contains entries !--- for all iSCSI targets ever logged into from this host. !--- You can manually edit the file and remove !--- entries so that the obsolete target no longer consumes an iSCSI target ID if a target is no longer available to a host. !--- Add an entry manually if you know the iSCSI target name !--- in advance and want it to be assigned a particular iSCSI target ID. !--- Stop the iSCSI driver before you edit the /etc/iscsi.bindings !--- file. Issue the !--- /etc/init.d/iscsi start command to manually start the iSCSI driver. !--- Issue the /etc/init.d/iscsi stop command to manually stop the iSCSI driver.

bash-2.05#cat /kernel/drv/sd.conf

name="sd" class="scsi" class_prop="atapi"
target=0 lun=0;

name="sd" class="scsi" target=1 lun=0;
name="sd" class="scsi" target=1 lun=1;
name="sd" class="scsi" target=1 lun=2;

# Start iSCSI auto-generated configuration -- do NOT alter or delete this line
# You may need to add additional lines to probe for additional LUNs
# or targets. You SHOULD delete any lines that represent iSCSI targets
# or LUNs that are not used.
name="sd" parent="iscsi" target=0 lun=0;
name="sd" parent="iscsi" target=1 lun=0;
name="sd" parent="iscsi" target=1 lun=1;
name="sd" parent="iscsi" target=1 lun=2;
name="sd" parent="iscsi" target=2 lun=3;
name="sd" parent="iscsi" target=2 lun=4;
name="sd" parent="iscsi" target=2 lun=5;
name="sd" parent="iscsi" target=2 lun=0;

# End iSCSI auto-generated configuration -- do NOT alter or delete this line


 !--- The corresponding entries for these devices must be made in the standard device configuration files !--- if the targets that get discovered by the iSCSI driver at any point in time !--- do not have a corresponding entry in the standard device configuration files (for example, /kernel/drv/sd.conf or /kernel/drv/st.conf). !--- Then reboot the system and issue the standard Solaris administrative commands !--- (devfsadm, drvconfig) once the system comes up. !--- You do not need to reboot the system if the entries in the device configuration files are already present. However, the standard device configuration !--- commands (devfsadm, drvconfig, and so on) must be issued to configure the !--- new iSCSI devices in the system.

canterbury (Cisco MDS 9216) 

!--- Output is suppressed.

vsan database
vsan 777

!--- VSAN 777 has been used for iSCSI targets. !--- Output is suppressed.

vsan database
vsan 777 interface fc1/4
vsan 777 interface fc1/7

!--- Output is suppressed.

boot system bootflash:/s112
boot kickstart bootflash:/k112

ip domain-name cisco.com
ip name-server 144.254.10.123
ip default-gateway 10.48.69.129

ip routing
iscsi authentication none
iscsi initiator ip-address 10.48.69.235

!--- Identifies the iSCSI initiator based on the IP address. A virtual N port is !--- created for each network interface card (NIC) or network interface.

  vsan 777

!--- VSAN 777 has been used for iSCSI targets. Configure the initiator IP address. !--- Targets via VSAN 777 are accessible by iSCSI initiators.

iscsi virtual-target name san-fc-jbod-1
  pWWN 21:00:00:20:37:67:f7:a2
advertise interface  GigabitEthernet2/1
initiator ip address 10.48.69.235 permit

!--- Create a static iSCSI virtual target for LUN 0, 1, and 2 of CLARiiON.

iscsi virtual-target name clariion
  pWWN 50:06:01:60:88:02:a8:2b fc-lun 0000 iscsi-lun 0000
  pWWN 50:06:01:60:88:02:a8:2b fc-lun 0001 iscsi-lun 0001
  pWWN 50:06:01:60:88:02:a8:2b fc-lun 0002 iscsi-lun 0002
advertise interface  GigabitEthernet2/1
initiator ip address 10.48.69.235 permit

!--- Create a static iSCSI virtual target for LUN 3, 4, and 5 of CLARiiON.

iscsi virtual-target name clariion-lun-3-4-5
  pWWN 50:06:01:60:88:02:a8:2b fc-lun 0003 iscsi-lun 0003
  pWWN 50:06:01:60:88:02:a8:2b fc-lun 0004 iscsi-lun 0004
  pWWN 50:06:01:60:88:02:a8:2b fc-lun 0005 iscsi-lun 0005
advertise interface  GigabitEthernet2/1
initiator ip address 10.48.69.235 permit

!--- Output is suppressed.

switchname canterbury

!--- Output is suppressed.

zone default-zone permit vsan 777

!--- Output is suppressed.

interface GigabitEthernet2/1
ip address 10.48.69.199 255.255.255.192
iscsi authentication none
switchport mtu 2156
no shutdown

!--- Output is suppressed.

interface fc1/4
no shutdown

!--- Output is suppressed.

interface fc1/7
no shutdown

 interface mgmt0
ip address 10.48.69.156 255.255.255.192

 interface iscsi2/1
no shutdown

Verificar

Use esta seção para confirmar se a sua configuração funciona corretamente.

A Output Interpreter Tool ( somente clientes registrados) (OIT) oferece suporte a determinados comandos show. Use a OIT para exibir uma análise da saída do comando show.

  • netstat -n — Verifica as conexões TCP no host Solaris.

  • iscsi-ls -l — Mostra os dispositivos que estão disponíveis no momento no host Solaris.

  • show zone status — Mostra informações da zona.

  • show fcns database vsan 777 — Mostra informações do servidor de nomes para uma VSAN específica.

  • show flogi database vsan 777 — Mostra informações de servidor de logon de estrutura (FLOGI) para uma VSAN específica.

  • show vsan member — Mostra informações de interface para diferentes VSANs.

  • show iscsi initiator detail — Mostra informações do iniciador iSCSI.

  • show iscsi initiator iscsi-session detail — Mostra informações detalhadas para a sessão do iniciador iSCSI.

  • show iscsi initiator fcp-session detail — Mostra informações detalhadas para a sessão FCP do iniciador iSCSI.

  • show ips stats tcp interface gigabitethernet 2/1 detail — Mostra estatísticas de TCP para uma interface GE específica.

  • show iscsi virtual-target configurado — Mostra os destinos virtuais iSCSI que foram configurados no Cisco MDS 9000.

  • show iscsi initiator configurado — Mostra os iniciadores iSCSI que foram configurados no Cisco MDS 9000.

  • show ips arp interface gigabitethernet 2/1 — Mostra informações de IP storage Address Resolution Protocol (ARP) para uma interface GE específica.

  • show scsi-target devices vsan 777 — Mostra dispositivos iSCSI para uma VSAN específica (para mapear LUNs FC para LUNs iSCSI).

  • show int iscsi 2/1 — Mostra interfaces iSCSI.

  • show iscsi stats iscsi 2/1 — Mostra estatísticas iSCSI.

  • show int gigabitethernet 2/1 — Mostra a interface GE.

  • show ip route — Mostra informações de rota IP.

Troubleshoot

Use esta seção para resolver problemas de configuração.

Procedimento de Troubleshooting

saída de babuíno 
bash-2.05# /etc/init.d/iscsi stop

iSCSI is stopping.
Aug 28 09:42:08 baboon iscsimod: iSCSIs: closing connection to target 2 at 10.48.69.199
Aug 28 09:42:08 baboon iscsimod: iSCSIs: closing connection to target 1 at 10.48.69.199
Aug 28 09:42:08 baboon iscsimod: iSCSIs: closing connection to target 0 at 10.48.69.199

bash-2.05# /etc/init.d/iscsi start

iSCSI is starting.

bash-2.05#bash-2.05# netstat -n

TCP: IPv4
   Local Address        Remote Address    Swind Send-Q Rwind Recv-Q  State
-------------------- -------------------- ----- ------ ----- ------ -------
10.48.69.235.32797   10.48.69.199.3260    65535      0 49172    0   ESTABLISHED
10.48.69.235.32798   10.48.69.199.3260    9379072    0 263152   0   ESTABLISHED
10.48.69.235.32799   10.48.69.199.3260    9379072    0 263152   0   ESTABLISHED

Active UNIX domain sockets
Address  Type          Vnode       Conn     Local Addr      Remote Addr
30002d95c88 dgram      30000205828 00000000 /tmp/portal

/etc/iscsi.bindings

#
0       0       san-fc-jbod-1
0       1       clariion

bash-2.05# devfsadm

Aug 28 09:45:04 baboon iscsimod: NOTICE: iSCSIs: bus 0 tgt 1 lun 0, Cmd 0x4d, Sense:
Aug 28 09:45:04 baboon iscsimod:     70000500 0000000a 00000000 20000000 0000
Aug 28 09:45:04 baboon iscsimod: NOTICE: iSCSIs: bus 0 tgt 1 lun 0, Cmd 0x5e, Sense:
Aug 28 09:45:04 baboon iscsimod:     70000500 0000000a 00000000 20000000 0000
Aug 28 09:45:04 baboon iscsimod: NOTICE: iSCSIs: bus 0 tgt 1 lun 1, Cmd 0x00, Sense:
Aug 28 09:45:04 baboon iscsimod:     70000600 0000000a 00000000 29000000 0000
Aug 28 09:45:04 baboon iscsimod: NOTICE: iSCSIs: bus 0 tgt 1 lun 1, Cmd 0x4d, Sense:
Aug 28 09:45:04 baboon iscsimod:     70000500 0000000a 00000000 20000000 0000
Aug 28 09:45:04 baboon iscsimod: NOTICE: iSCSIs: bus 0 tgt 1 lun 1, Cmd 0x5e, Sense:
Aug 28 09:45:04 baboon iscsimod:     70000500 0000000a 00000000 20000000 0000
Aug 28 09:45:04 baboon iscsimod: NOTICE: iSCSIs: bus 0 tgt 1 lun 2, Cmd 0x00, Sense:
Aug 28 09:45:04 baboon iscsimod:     70000600 0000000a 00000000 29000000 0000
Aug 28 09:45:04 baboon iscsimod: NOTICE: iSCSIs: bus 0 tgt 1 lun 2, Cmd 0x4d, Sense:
Aug 28 09:45:04 baboon iscsimod:     70000500 0000000a 00000000 20000000 0000
Aug 28 09:45:04 baboon iscsimod: NOTICE: iSCSIs: bus 0 tgt 1 lun 2, Cmd 0x5e, Sense:
Aug 28 09:45:04 baboon iscsimod:     70000500 0000000a 00000000 20000000 0000
Aug 28 09:45:05 baboon iscsimod: NOTICE: iSCSIs: bus 0 tgt 0 lun 0, Cmd 0x1c, Sense:
Aug 28 09:45:05 baboon iscsimod:     70000500 0000000a 00000000 35010300 0000

bash-2.05# format output

AVAILABLE DISK SELECTIONS:
       0. c0t0d0 <SUN18G cyl 7506 alt 2 hd 19 sec 248>
          /pci@1f,4000/scsi@3/sd@0,0
       1. c0t1d0 <SUN18G cyl 7506 alt 2 hd 19 sec 248>
          /pci@1f,4000/scsi@3/sd@1,0
       2. c3t0d0 <SEAGATE-ST318203FC-0004 cyl 9770 alt 2 hd 12 sec 303>
          /iscsipseudo/iscsi@0/sd@0,0
       3. c3t1d0 <DGC-RAID0-0632 cyl 5459 alt 2 hd 3 sec 128>
          /iscsipseudo/iscsi@0/sd@1,0
       4. c3t1d1 <DGC-RAID0-0632 cyl 5459 alt 2 hd 3 sec 128>
          /iscsipseudo/iscsi@0/sd@1,1
       5. c3t1d2 <DGC-RAID0-0632 cyl 5459 alt 2 hd 3 sec 128>
          /iscsipseudo/iscsi@0/sd@1,2
       6. c3t2d0 <drive not available>
          /iscsipseudo/iscsi@0/sd@2,0

!--- After you add the clariion-lun-3-4-5 virtual target on the Cisco MDS 9216.

/etc/iscsi.bindings

0       0       san-fc-jbod-1
0       1       clariion
0       2       clariion-lun-3-4-5

bash-2.05#bash-2.05# netstat -n

TCP: IPv4
   Local Address        Remote Address    Swind Send-Q Rwind Recv-Q  State
-------------------- -------------------- ----- ------ ----- ------ -------
10.48.69.235.32797   10.48.69.199.3260    65535      0 49172      0 TIME_WAIT
10.48.69.235.32798   10.48.69.199.3260    9379072    0 263152     0 ESTABLISHED
10.48.69.235.32799   10.48.69.199.3260    9379072    0 263152     0 ESTABLISHED
10.48.69.235.32800   10.48.69.199.3260    65535      0 49108      0 ESTABLISHED
10.48.69.235.32801   10.48.69.199.3260    9379072    0 263152     0 ESTABLISHED

Active UNIX domain sockets
Address  Type          Vnode       Conn     Local Addr      Remote Addr
30002d95c88 dgram      30000205828 00000000 /tmp/portal

bash-2.05# devfsadm

Aug 28 09:47:58 baboon iscsimod: NOTICE: iSCSIs: bus 0 tgt 2 lun 3, Cmd 0x00, Sense:
Aug 28 09:47:58 baboon iscsimod:     70000600 0000000a 00000000 29000000 0000
Aug 28 09:47:58 baboon iscsimod: NOTICE: iSCSIs: bus 0 tgt 2 lun 3, Cmd 0x4d, Sense:
Aug 28 09:47:58 baboon iscsimod:     70000500 0000000a 00000000 20000000 0000
Aug 28 09:47:58 baboon iscsimod: NOTICE: iSCSIs: bus 0 tgt 2 lun 3, Cmd 0x5e, Sense:
Aug 28 09:47:58 baboon iscsimod:     70000500 0000000a 00000000 20000000 0000
Aug 28 09:47:58 baboon iscsimod: NOTICE: iSCSIs: bus 0 tgt 2 lun 4, Cmd 0x00, Sense:
Aug 28 09:47:58 baboon iscsimod:     70000600 0000000a 00000000 29000000 0000
Aug 28 09:47:58 baboon iscsimod: NOTICE: iSCSIs: bus 0 tgt 2 lun 4, Cmd 0x5e, Sense:
Aug 28 09:47:58 baboon iscsimod:     70000500 0000000a 00000000 20000000 0000
Aug 28 09:47:58 baboon iscsimod: NOTICE: iSCSIs: bus 0 tgt 2 lun 5, Cmd 0x00, Sense:
Aug 28 09:47:58 baboon iscsimod:     70000600 0000000a 00000000 29000000 0000
Aug 28 09:47:58 baboon iscsimod: NOTICE: iSCSIs: bus 0 tgt 2 lun 5, Cmd 0x4d, Sense:
Aug 28 09:47:58 baboon iscsimod:     70000500 0000000a 00000000 20000000 0000
Aug 28 09:47:58 baboon iscsimod: NOTICE: iSCSIs: bus 0 tgt 2 lun 5, Cmd 0x5e, Sense:
Aug 28 09:47:58 baboon iscsimod:     70000500 0000000a 00000000 20000000 0000

And the format output:
       0. c0t0d0 <SUN18G cyl 7506 alt 2 hd 19 sec 248>
          /pci@1f,4000/scsi@3/sd@0,0
       1. c0t1d0 <SUN18G cyl 7506 alt 2 hd 19 sec 248>
          /pci@1f,4000/scsi@3/sd@1,0
       2. c3t0d0 <SEAGATE-ST318203FC-0004 cyl 9770 alt 2 hd 12 sec 303>
          /iscsipseudo/iscsi@0/sd@0,0
       3. c3t1d0 <DGC-RAID0-0632 cyl 5459 alt 2 hd 3 sec 128>
          /iscsipseudo/iscsi@0/sd@1,0
       4. c3t1d1 <DGC-RAID0-0632 cyl 5459 alt 2 hd 3 sec 128>
          /iscsipseudo/iscsi@0/sd@1,1
       5. c3t1d2 <DGC-RAID0-0632 cyl 5459 alt 2 hd 3 sec 128>
          /iscsipseudo/iscsi@0/sd@1,2
       6. c3t2d0 <drive not available>
          /iscsipseudo/iscsi@0/sd@2,0
       7. c3t2d3 <DGC-RAID0-0632 cyl 10920 alt 2 hd 3 sec 128>
          /iscsipseudo/iscsi@0/sd@2,3
       8. c3t2d4 <DGC-RAID0-0632 cyl 5459 alt 2 hd 3 sec 128>
          /iscsipseudo/iscsi@0/sd@2,4
       9. c3t2d5 <DGC-RAID0-0632 cyl 5459 alt 2 hd 3 sec 128>
          /iscsipseudo/iscsi@0/sd@2,5

!--- Issue the iscsi-ls -v command to see iSCSI driver version.

bash-2.05# iscsi-ls -v

iSCSI driver version: 3.3.3

!--- Issue the iscsi-ls -l or iscsi-ls commands to see the devices that are currently available.

bash-2.05# iscsi-ls -l

********************************************************************************
TARGET NAME san-fc-jbod-1
TARGET ID 0:
  ADDRESS = 10.48.69.199:3260, 128
  STATUS  = Connected 10.48.69.235:32798<->10.48.69.199:3260  8/28/2003 09:43:59
  SESSION = ISID 00023d000001  TSID 128  PID 463
  LUN   0 = DISK c3t0d0 (sd296) 'SEAGATE-ST318203FC-0004' SERIAL# LRE80915
            BLOCKS: 35566479  BLOCK SIZE: 512
********************************************************************************
TARGET NAME clariion
TARGET ID 1:
  ADDRESS = 10.48.69.199:3260, 128
  STATUS  = Connected 10.48.69.235:32799<->10.48.69.199:3260  8/28/2003 09:43:59
  SESSION = ISID 00023d000001  TSID 128  PID 464
  LUN   0 = DISK c3t1d0 (sd297) 'DGC-RAID 0-0632' SERIAL# 008E080000CL
            BLOCKS: 2097023  BLOCK SIZE: 512
  LUN   1 = DISK c3t1d1 (sd298) 'DGC-RAID 0-0632' SERIAL# 0127AB0000CL
            BLOCKS: 2097023  BLOCK SIZE: 512
  LUN   2 = DISK c3t1d2 (sd299) 'DGC-RAID 0-0632' SERIAL# 02E4180000CL
            BLOCKS: 2097023  BLOCK SIZE: 512
********************************************************************************
TARGET NAME clariion-lun-3-4-5
TARGET ID 2:
  ADDRESS = 10.48.69.199:3260, 128
  STATUS  = Connected 10.48.69.235:32801<->10.48.69.199:3260  8/28/2003 09:46:42
  SESSION = ISID 00023d000001  TSID 128  PID 482
  LUN   0 : SCSI Inquiry failed - Bad file number
  LUN   3 = DISK c3t2d3 (sd371) 'DGC-RAID 0-0632' SERIAL# 03E0A1E330CL
            BLOCKS: 4194047  BLOCK SIZE: 512
  LUN   4 = DISK c3t2d4 (sd372) 'DGC-RAID 0-0632' SERIAL# 04E9A1E330CL
            BLOCKS: 2097023  BLOCK SIZE: 512
  LUN   5 = DISK c3t2d5 (sd373) 'DGC-RAID 0-0632' SERIAL# 0594B1E330CL
            BLOCKS: 2097023  BLOCK SIZE: 512
********************************************************************************

 !-- Issue the iscsi-ls -c command to see detailed statistics for currently established iSCSI sessions.

bash-2.05# iscsi-ls -c

********************************************************************************
TARGET NAME san-fc-jbod-1
TARGET ID 0:
  ADDRESS = 10.48.69.199:3260, 128
  STATUS  = Connected 10.48.69.235:32798<->10.48.69.199:3260  8/28/2003 09:43:59
  SESSION = ISID 00023d000001  TSID 128  PID 463
  InitialR2T               = Yes
  MaxRecvDataSegmentLength = 131072 Bytes
  MaxXmitDataSegmentLength = 2048 Bytes
  FirstBurstLength         = 262144 Bytes
  MaxBurstLength           = 16776192 Bytes
  LoginTimeout             = 15 Seconds
  AuthTimeout              = 45 Seconds
  ActiveTimeout            = 5 Seconds
  IdleTimeout              = 60 Seconds
  PingTimeout              = 5 Seconds
  HeaderDigest             = None
  DataDigest               = None
  ConnFailTimeout          = Default
  MultiPath                = None
********************************************************************************
TARGET NAME clariion
TARGET ID 1:
  ADDRESS = 10.48.69.199:3260, 128
  STATUS  = Connected 10.48.69.235:32799<->10.48.69.199:3260  8/28/2003 09:43:59
  SESSION = ISID 00023d000001  TSID 128  PID 464
  InitialR2T               = Yes
  MaxRecvDataSegmentLength = 131072 Bytes
  MaxXmitDataSegmentLength = 2048 Bytes
  FirstBurstLength         = 262144 Bytes
  MaxBurstLength           = 16776192 Bytes
  LoginTimeout             = 15 Seconds
  AuthTimeout              = 45 Seconds
  ActiveTimeout            = 5 Seconds
  IdleTimeout              = 60 Seconds
  PingTimeout              = 5 Seconds
  HeaderDigest             = None
  DataDigest               = None
  ConnFailTimeout          = Default
  MultiPath                = None
********************************************************************************
TARGET NAME clariion-lun-3-4-5
TARGET ID 2:
  ADDRESS = 10.48.69.199:3260, 128
  STATUS  = Connected 10.48.69.235:32801<->10.48.69.199:3260  8/28/2003 09:46:42
  SESSION = ISID 00023d000001  TSID 128  PID 482
  InitialR2T               = Yes
  MaxRecvDataSegmentLength = 131072 Bytes
  MaxXmitDataSegmentLength = 2048 Bytes
  FirstBurstLength         = 262144 Bytes
  MaxBurstLength           = 16776192 Bytes
  LoginTimeout             = 15 Seconds
  AuthTimeout              = 45 Seconds
  ActiveTimeout            = 5 Seconds
  IdleTimeout              = 60 Seconds
  PingTimeout              = 5 Seconds
  HeaderDigest             = None
  DataDigest               = None
  ConnFailTimeout          = Default
  MultiPath                = None
********************************************************************************

!--- You can see these iSCSI connections in the /var/adm/messages or dmesg:

Aug 28 09:43:59 baboon iscsid[454]: [ID 702911 daemon.notice]
   version 3.3.3 ( 7-Aug-2003)
Aug 28 09:43:59 baboon iscsid[463]: [ID 702911 daemon.notice]
   iSCSI normal session to san-fc-jbod-1 estabished
Aug 28 09:43:59 baboon iscsid[463]: [ID 702911 daemon.notice]
   logged into target san-fc-jbod-1 -- id 0, Initiator sid 00023d000001, target sid 128
Aug 28 09:43:59 baboon iscsid[464]: [ID 702911 daemon.notice]
   iSCSI normal session to clariion estabished
Aug 28 09:43:59 baboon iscsid[464]: [ID 702911 daemon.notice]
   logged into target clariion -- id 1, Initiator sid 00023d000001, target sid 128
Aug 28 09:45:23 baboon iscsi: [ID 318680 kern.notice] NOTICE:
   tran_start disabled to bus 0, target 2, lun 0
Aug 28 09:46:42 baboon iscsid[482]: [ID 702911 daemon.notice]
   iSCSI normal session to clariion-lun-3-4-5 established
Aug 28 09:46:42 baboon iscsid[482]: [ID 702911 daemon.notice]
   logged into target clariion-lun-3-4-5 -- id 2, Initiator sid 00023d000001,
   target sid 128

Saída canterbury do Cisco MDS 9216 
canterbury#show zone status

VSAN: 1 default-zone: permit distribute: active only Interop: Off
Full Zoning Database :
    Zonesets:0  Zones:0 Aliases: 0
Active Zoning Database :
    Database Not Available
Status: Deactivation completed at Fri Aug 22 11:47:53 2003

VSAN: 777 default-zone: permit distribute: active only Interop: Off.
Full Zoning Database :
    Zonesets:0  Zones:0 Aliases: 0
Active Zoning Database :
    Database Not Available
Status: Default zoning policy changed to permit at Mon Aug 25 20:19:31 2003

!--- VSAN 777 has been used for this configuration, and default-zone behavior has been !--- set to permit.

canterbury#show flogi da vsan 777

---------------------------------------------------------------------------
INTERFACE  VSAN    FCID            PORT NAME               NODE NAME
---------------------------------------------------------------------------
fc1/4      777   0x7000e8  21:00:00:20:37:67:f7:a2  20:00:00:20:37:67:f7:a2
fc1/7      777   0x700103  50:06:01:60:88:02:a8:2b  50:06:01:60:11:02:a8:2b
iscsi2/1   777   0x700100  21:02:00:0c:30:6c:24:42  21:01:00:0c:30:6c:24:42

Total number of flogi = 3.

canterbury#show fcns database vsan 777

VSAN 777:
--------------------------------------------------------------------------
FCID        TYPE  PWWN                    (VENDOR)        FC4-TYPE:FEATURE
--------------------------------------------------------------------------
0x7000e8    NL    21:00:00:20:37:67:f7:a2 (Seagate)       scsi-fcp:target
0x700100    N     21:02:00:0c:30:6c:24:42 (Cisco)         scsi-fcp:init isc..w
0x700103    N     50:06:01:60:88:02:a8:2b (Clariion)      scsi-fcp:target

Total number of entries = 3

!--- FCID 0X700100 is the virtual N port (HBA) for the iSCSI host.

canterbury#show fcns database detail vsan 777

------------------------
VSAN:777   FCID:0x7000e8
------------------------
port-wwn (vendor)     :21:00:00:20:37:67:f7:a2 (Seagate)
node-wwn              :20:00:00:20:37:67:f7:a2
class                 :3
node-ip-addr          :0.0.0.0
ipa                   :ff ff ff ff ff ff ff ff
fc4-types:fc4_features:scsi-fcp:target
symbolic-port-name    :
symbolic-node-name    :
port-type             :NL
port-ip-addr          :0.0.0.0
fabric-port-wwn       :20:04:00:0c:30:6c:24:40
hard-addr             :0x000000
------------------------
VSAN:777   FCID:0x700100
------------------------
port-wwn (vendor)     :21:02:00:0c:30:6c:24:42 (Cisco)
node-wwn              :21:01:00:0c:30:6c:24:42
class                 :2,3
node-ip-addr          :10.48.69.235
ipa                   :ff ff ff ff ff ff ff ff
fc4-types:fc4_features:scsi-fcp:init iscsi-gw

!--- Virtual N port for host.

symbolic-port-name    :
symbolic-node-name    :10.48.69.235
port-type             :N 
port-ip-addr          :0.0.0.0
fabric-port-wwn       :20:41:00:0c:30:6c:24:40
hard-addr             :0x000000
------------------------
VSAN:777   FCID:0x700103
------------------------
port-wwn (vendor)     :50:06:01:60:88:02:a8:2b (Clariion)
node-wwn              :50:06:01:60:11:02:a8:2b
class                 :3
node-ip-addr          :0.0.0.0
ipa                   :ff ff ff ff ff ff ff ff
fc4-types:fc4_features:scsi-fcp:target
symbolic-port-name    :
symbolic-node-name    :
port-type             :N
port-ip-addr          :0.0.0.0
fabric-port-wwn       :20:07:00:0c:30:6c:24:40
hard-addr             :0x000000

Total number of entries = 3

canterbury#show vsan membership

vsan 777 interfaces:
        fc1/4   fc1/7

canterbury#show iscsi initiator

iSCSI Node name is 10.48.69.235
    iSCSI Initiator name: iqn.1987-05.com.cisco:01.894b196796e7
    iSCSI alias name: baboon
    Node WWN is 21:01:00:0c:30:6c:24:42 (dynamic)
    Member of vsans: 777
    Number of Virtual n_ports: 1
    Virtual Port WWN is 21:02:00:0c:30:6c:24:42 (dynamic)
      Interface iSCSI 2/1, Portal group tag: 0x80
      VSAN ID 777, FCID 0x700100

canterbury#show iscsi initiator detail

iSCSI Node name is 10.48.69.235
    iSCSI Initiator name: iqn.1987-05.com.cisco:01.894b196796e7
    iSCSI alias name: baboon
    Node WWN is 21:01:00:0c:30:6c:24:42 (dynamic)
    Member of vsans: 777
    Number of Virtual n_ports: 1

    Virtual Port WWN is 21:02:00:0c:30:6c:24:42 (dynamic)
      Interface iSCSI 2/1, Portal group tag is 0x80
      VSAN ID 777, FCID 0x700100
      2 FC sessions, 3 iSCSI sessions
      iSCSI session details
        Target: san-fc-jbod-1
          Statistics:
            PDU: Command: 24, Response: 24
            Bytes: TX: 3504, RX: 0
            Number of connection: 1
          TCP parameters
            Local 10.48.69.199:3260, Remote 10.48.69.235:32798
            Path MTU: 1500 bytes
            Retransmission timeout: 300 ms
            Round trip time: Smoothed 4 ms, Variance: 6
            Advertized window: Current: 256 KB, Maximum: 257 KB, Scale: 3
            Peer receive window: Current: 9159 KB, Maximum: 9159 KB, Scale: 8
            Congestion window: Current: 11 KB
        Target: clariion-lun-3-4-5
          Statistics:
            PDU: Command: 73, Response: 73
            Bytes: TX: 9740, RX: 0
            Number of connection: 1
          TCP parameters
            Local 10.48.69.199:3260, Remote 10.48.69.235:32801
            Path MTU: 1500 bytes
            Retransmission timeout: 300 ms
            Round trip time: Smoothed 7 ms, Variance: 13
            Advertized window: Current: 256 KB, Maximum: 257 KB, Scale: 3
            Peer receive window: Current: 9159 KB, Maximum: 9159 KB, Scale: 8
            Congestion window: Current: 11 KB
        Target: clariion
          Statistics:
            PDU: Command: 101, Response: 101
            Bytes: TX: 14828, RX: 0
            Number of connection: 1
          TCP parameters
            Local 10.48.69.199:3260, Remote 10.48.69.235:32799
            Path MTU: 1500 bytes
            Retransmission timeout: 300 ms
            Round trip time: Smoothed 2 ms, Variance: 1
            Advertised window: Current: 256 KB, Maximum: 257 KB, Scale: 3
            Peer receive window: Current: 9159 KB, Maximum: 9159 KB, Scale: 8
            Congestion window: Current: 11 KB

      FCP Session details
        Target FCID: 0x7000e8 (S_ID of this session: 0x700100)
          pWWN: 21:00:00:20:37:67:f7:a2, nWWN: 20:00:00:20:37:67:f7:a2
          Session state: LOGGED_IN
          1 iSCSI sessions share this FC session
            Target: san-fc-jbod-1
          Negotiated parameters
            RcvDataFieldSize 2048 our_RcvDataFieldSize 2048
            MaxBurstSize 0, EMPD: FALSE
            Random Relative Offset: FALSE, Sequence-in-order: Yes
          Statistics:
            PDU: Command: 0, Response: 24
        Target FCID: 0x700103 (S_ID of this session: 0x700100)
          pWWN: 50:06:01:60:88:02:a8:2b, nWWN: 50:06:01:60:11:02:a8:2b
          Session state: LOGGED_IN
          2 iSCSI sessions share this FC session
            Target: clariion-lun-3-4-5
            Target: clariion
          Negotiated parameters
            RcvDataFieldSize 1024 our_RcvDataFieldSize 2048
            MaxBurstSize 0, EMPD: FALSE
            Random Relative Offset: FALSE, Sequence-in-order: Yes
          Statistics:
            PDU: Command: 0, Response: 174

canterbury#show iscsi initiator iscsi-session detail

iSCSI Node name is 10.48.69.235
    iSCSI Initiator name: iqn.1987-05.com.cisco:01.894b196796e7
    iSCSI alias name: baboon
    Node WWN is 21:01:00:0c:30:6c:24:42 (dynamic)
    Member of vsans: 777
    Number of Virtual n_ports: 1

    Virtual Port WWN is 21:02:00:0c:30:6c:24:42 (dynamic)
      Interface iSCSI 2/1, Portal group tag is 0x80
      VSAN ID 777, FCID 0x700100
      2 FC sessions, 3 iSCSI sessions
      iSCSI session details
        Target: san-fc-jbod-1
          Statistics:
            PDU: Command: 24, Response: 24
            Bytes: TX: 3504, RX: 0
            Number of connection: 1
          TCP parameters
            Local 10.48.69.199:3260, Remote 10.48.69.235:32798
            Path MTU: 1500 bytes
            Retransmission timeout: 300 ms
            Round trip time: Smoothed 4 ms, Variance: 6
            Advertized window: Current: 256 KB, Maximum: 257 KB, Scale: 3
            Peer receive window: Current: 9159 KB, Maximum: 9159 KB, Scale: 8
            Congestion window: Current: 11 KB
        Target: clariion-lun-3-4-5
          Statistics:
            PDU: Command: 73, Response: 73
            Bytes: TX: 9740, RX: 0
            Number of connection: 1
          TCP parameters
            Local 10.48.69.199:3260, Remote 10.48.69.235:32801
            Path MTU: 1500 bytes
            Retransmission timeout: 300 ms
            Round trip time: Smoothed 7 ms, Variance: 13
            Advertized window: Current: 256 KB, Maximum: 257 KB, Scale: 3
            Peer receive window: Current: 9159 KB, Maximum: 9159 KB, Scale: 8
            Congestion window: Current: 11 KB
        Target: clariion
          Statistics:
            PDU: Command: 101, Response: 101
            Bytes: TX: 14828, RX: 0
            Number of connection: 1
          TCP parameters
            Local 10.48.69.199:3260, Remote 10.48.69.235:32799
            Path MTU: 1500 bytes
            Retransmission timeout: 300 ms
            Round trip time: Smoothed 2 ms, Variance: 1
            Advertized window: Current: 256 KB, Maximum: 257 KB, Scale: 3
            Peer receive window: Current: 9159 KB, Maximum: 9159 KB, Scale: 8
            Congestion window: Current: 11 KB

canterbury#show iscsi initiator fcp-session detail

iSCSI Node name is 10.48.69.235
    iSCSI Initiator name: iqn.1987-05.com.cisco:01.894b196796e7
    iSCSI alias name: baboon
    Node WWN is 21:01:00:0c:30:6c:24:42 (dynamic)
    Member of vsans: 777
    Number of Virtual n_ports: 1

    Virtual Port WWN is 21:02:00:0c:30:6c:24:42 (dynamic)
      Interface iSCSI 2/1, Portal group tag is 0x80
      VSAN ID 777, FCID 0x700100
      2 FC sessions, 3 iSCSI sessions

      FCP Session details
        Target FCID: 0x7000e8 (S_ID of this session: 0x700100)
          pWWN: 21:00:00:20:37:67:f7:a2, nWWN: 20:00:00:20:37:67:f7:a2
          Session state: LOGGED_IN
          1 iSCSI sessions share this FC session
            Target: san-fc-jbod-1
          Negotiated parameters
            RcvDataFieldSize 2048 our_RcvDataFieldSize 2048
            MaxBurstSize 0, EMPD: FALSE
            Random Relative Offset: FALSE, Sequence-in-order: Yes
          Statistics:
            PDU: Command: 0, Response: 24
        Target FCID: 0x700103 (S_ID of this session: 0x700100)
          pWWN: 50:06:01:60:88:02:a8:2b, nWWN: 50:06:01:60:11:02:a8:2b
          Session state: LOGGED_IN
          2 iSCSI sessions share this FC session
            Target: clariion-lun-3-4-5
            Target: clariion
          Negotiated parameters
            RcvDataFieldSize 1024 our_RcvDataFieldSize 2048
            MaxBurstSize 0, EMPD: FALSE
            Random Relative Offset: FALSE, Sequence-in-order: Yes
          Statistics:
            PDU: Command: 0, Response: 174

canterbury#show ips stats tcp interface gigabitethernet 2/1 detail

TCP Statistics for port GigabitEthernet2/1
    TCP send stats
      28621 segments, 4231096 bytes
      15842 data, 12335 ack only packets
      168 control (SYN/FIN/RST), 0 probes, 210 window updates
      66 segments retransmitted, 63724 bytes
      66 retransmitted while on ethernet send queue, 1127 packets split
      480 delayed acks sent
    TCP receive stats
      36728 segments, 12911 data packets in sequence, 2668162 bytes in sequence
      0 predicted ack, 12050 predicted data
      0 bad checksum, 0 multi/broadcast, 0 bad offset
      0 no memory drops, 0 short segments
      48 duplicate bytes, 1 duplicate packets
      0 partial duplicate bytes, 0 partial duplicate packets
      0 out-of-order bytes, 164 out-of-order packets
      0 packet after window, 0 bytes after window
      0 packets after close
      12621 acks, 3486850 ack bytes, 0 ack toomuch, 11652 duplicate acks
      0 ack packets left of snd_una, 6 non-4 byte aligned packets
      8333 window updates, 0 window probe
      624 pcb hash miss, 79 no port, 0 bad SYN, 0 paws drops
    TCP Connection Stats
      0 attempts, 231 accepts, 231 established
      227 closed, 14 drops, 0 conn drops
      0 drop in retransmit timeout, 2 drop in keepalive timeout
      0 drop in persist drops, 0 connections drained
    TCP Miscellaneous Stats
      11761 segments timed, 12027 rtt updated
      51 retransmit timeout, 304 persist timeout
      10452 keepalive timeout, 10450 keepalive probes
    TCP SACK Stats
      0 recovery episodes, 0 data packets, 0 data bytes
      0 data packets retransmitted, 0 data bytes retransmitted
      0 connections closed, 0 retransmit timeouts
    TCP SYN Cache Stats
      233 entries, 231 connections completed, 1 entries timed out
      0 dropped due to overflow, 1 dropped due to RST
      0 dropped due to ICMP unreach, 0 dropped due to bucket overflow
      0 abort due to no memory, 4 duplicate SYN, 76 no-route SYN drop
      0 hash collisions, 0 retransmitted

    TCP Active Connections
      Local  Address        Remote Address        State      Send-Q   Recv-Q
      10.48.69.199:3260     10.48.69.235:32798    ESTABLISH  0        0
      10.48.69.199:3260     10.48.69.235:32799    ESTABLISH  0        0
      10.48.69.199:3260     10.48.69.235:32800    ESTABLISH  0        0
      10.48.69.199:3260     10.48.69.235:32801    ESTABLISH  0        0
      0.0.0.0:3260          0.0.0.0:0             LISTEN     0        0

canterbury#show iscsi virtual-target configured

target: san-fc-jbod-1
  * Port WWN 21:00:00:20:37:67:f7:a2

!--- The * means that you have both discovery and target sessions. !--- You only have a discovery session if there is no * in front of the pWWN.

    Configured node
    No. of advertised interface: 1
      GigabitEthernet 2/1
    No. of initiators permitted: 3
      initiator iqn.1987-05.com.cisco.02.89451e183581.mcandege-w2k1 is permitted
      initiator 10.48.69.235/32 is permitted
      initiator 10.48.69.232/32 is permitted
    all initiator permit is disabled

target: clariion
  * Port WWN 50:06:01:60:88:02:a8:2b
    Configured node
    No. of LU mapping: 3
      iSCSI LUN: 0000, FC LUN: 0000
      iSCSI LUN: 0001, FC LUN: 0001
      iSCSI LUN: 0002, FC LUN: 0002
    No. of advertised interface: 1
      GigabitEthernet 2/1
    No. of initiators permitted: 1
      initiator 10.48.69.235/32 is permitted
    all initiator permit is disabled

target: clariion-lun-3-4-5
  * Port WWN 50:06:01:60:88:02:a8:2b
    Configured node
    No. of LU mapping: 3
      iSCSI LUN: 0003, FC LUN: 0003
      iSCSI LUN: 0004, FC LUN: 0004
      iSCSI LUN: 0005, FC LUN: 0005
    No. of advertised interface: 1
      GigabitEthernet 2/1
    No. of initiators permitted: 1
      initiator 10.48.69.235/32 is permitted
    all initiator permit is disabled

canterbury#show iscsi initiator configured 

iSCSI Node name is 10.48.69.235
    Member of vsans: 777

canterbury#show ips arp interface gigabitethernet 2/1

Protocol         Address   Age (min)   Hardware Addr  Type   Interface
Internet    10.48.69.200        0     0008.e21e.c7bc  ARPA  GigabitEthernet2/1
Internet    10.48.69.206        7     0005.9ba6.95ff  ARPA  GigabitEthernet2/1
Internet    10.48.69.209        4     0009.7c60.561f  ARPA  GigabitEthernet2/1
Internet    10.48.69.226        0     0060.08f6.bc1a  ARPA  GigabitEthernet2/1
Internet    10.48.69.229       15     0800.209e.edab  ARPA  GigabitEthernet2/1
Internet    10.48.69.233        0     0010.4200.7d5b  ARPA  GigabitEthernet2/1
Internet    10.48.69.235        9     0800.20b6.6559  ARPA  GigabitEthernet2/1
Internet    10.48.69.238        5     0030.6e1b.6f51  ARPA  GigabitEthernet2/1
Internet    10.48.69.239       12     0030.6e1c.a00b  ARPA  GigabitEthernet2/1
Internet    10.48.69.248        5     0202.3d30.45f8  ARPA  GigabitEthernet2/1
Internet    10.48.69.252        1     0202.3d30.45fc  ARPA  GigabitEthernet2/1
Internet      10.10.2.28        9     0202.3d0a.021c  ARPA  GigabitEthernet2/1

canterbury#show scsi-target devices vsan 777

--------------------------------------------------------------------------------
VSAN    FCID        PWWN                      VENDOR    MODEL             REV
--------------------------------------------------------------------------------
777     0x7000e8    21:00:00:20:37:67:f7:a2   SEAGATE   ST318203FC        0004
777     0x700103    50:06:01:60:88:02:a8:2b   DGC       RAID 0            0632

canterbury#show scsi-target lun vsan 777

- ST318203FC from SEAGATE (Rev 0004)
  FCID is 0x7000e8 in VSAN 777, PWWN is 21:00:00:20:37:67:f7:a2
  ------------------------------------------------------------------------------
  LUN    Capacity  Status  Serial Number    Device-Id
         (MB)
  ------------------------------------------------------------------------------
  0x0    18210     Online  LRE8091500007039 C:1 A:0 T:3 20:00:00:20:37:67:f7:a2
- RAID from DGC (Rev 0632)
  FCID is 0x700103 in VSAN 777, PWWN is 50:06:01:60:88:02:a8:2b
  ------------------------------------------------------------------------------
  LUN    Capacity  Status  Serial Number    Device-Id
         (MB)
  ------------------------------------------------------------------------------
  0x0    1074      Online  f60004202091     C:1 A:0 T:3 60:06:01:60:88:02:a8:2b
                                                        da:05:b6:a9:b6:9d:7b:00
                                            C:1 A:0 T:0 00:00:00:00
  0x1    1074      Online  f60004202091     C:1 A:0 T:3 60:06:01:60:88:02:a8:2b
                                                        6a:66:0d:74:cb:33:88:6c
                                            C:1 A:0 T:0 00:01:00:00
  0x2    1074      Online  f60004202091     C:1 A:0 T:3 60:06:01:60:88:02:a8:2b
                                                        ec:81:5b:a2:c4:43:0d:8a
                                            C:1 A:0 T:0 00:02:00:00
  0x3    2147      Online  f60004202091     C:1 A:0 T:3 60:06:01:60:88:02:a8:2b
                                                        e0:47:b3:be:3b:00:e0:d5
                                            C:1 A:0 T:0 00:03:00:00
  0x4    1074      Online  f60004202091     C:1 A:0 T:3 60:06:01:60:88:02:a8:2b
                                                        00:51:5b:7f:3d:9a:7b:ce
                                            C:1 A:0 T:0 00:04:00:00
  0x5    1074      Online  f60004202091     C:1 A:0 T:3 60:06:01:60:88:02:a8:2b
                                                        ab:b1:ae:80:59:c0:fc:f0
                                            C:1 A:0 T:0 00:05:00:00
  0x6    1074      Online  f60004202091     C:1 A:0 T:3 60:06:01:60:88:02:a8:2b
                                                        ad:91:58:af:d2:fd:c7:47
                                            C:1 A:0 T:0 00:06:00:00
  0x7    1074      Online  f60004202091     C:1 A:0 T:3 60:06:01:60:88:02:a8:2b
                                                        b1:ef:e7:6c:44:5c:16:97
                                            C:1 A:0 T:0 00:07:00:00
  0x8    1074      Online  f60004202091     C:1 A:0 T:3 60:06:01:60:88:02:a8:2b
                                                        84:4f:09:60:30:1e:fc:50
                                            C:1 A:0 T:0 00:08:00:00
  0x9    1074      Online  f60004202091     C:1 A:0 T:3 60:06:01:60:88:02:a8:2b
                                                        aa:6d:e2:0e:ce:7a:cc:21
                                            C:1 A:0 T:0 00:09:00:00
  0xa    1074      Online  f60004202091     C:1 A:0 T:3 60:06:01:60:88:02:a8:2b
                                                        5b:66:67:89:6c:f2:d1:56
                                            C:1 A:0 T:0 00:0a:00:00
  0xb    1074      Online  f60004202091     C:1 A:0 T:3 60:06:01:60:88:02:a8:2b
                                                        a9:32:bd:04:4a:bb:3d:9b
                                            C:1 A:0 T:0 00:0b:00:00
  0xc    1074      Online  f60004202091     C:1 A:0 T:3 60:06:01:60:88:02:a8:2b
                                                        cd:d9:96:f7:57:3f:07:0c
                                            C:1 A:0 T:0 00:0c:00:00
  0xd    1074      Online  f60004202091     C:1 A:0 T:3 60:06:01:60:88:02:a8:2b
                                                        0c:e5:ba:39:68:ca:d6:f0
                                            C:1 A:0 T:0 00:0d:00:00
  0xe    1074      Online  f60004202091     C:1 A:0 T:3 60:06:01:60:88:02:a8:2b
                                                        60:6e:ee:76:98:fc:ab:97
                                            C:1 A:0 T:0 00:0e:00:00
  0xf    1074      Online  f60004202091     C:1 A:0 T:3 60:06:01:60:88:02:a8:2b
                                                        8b:58:80:7b:12:fb:6b:12
                                            C:1 A:0 T:0 00:0f:00:00
  0x10   1074      Online  f60004202091     C:1 A:0 T:3 60:06:01:60:88:02:a8:2b
                                                        a1:2f:6d:b0:c3:d6:c2:46
                                            C:1 A:0 T:0 00:10:00:00
  0x11   1074      Online  f60004202091     C:1 A:0 T:3 60:06:01:60:88:02:a8:2b
                                                        2c:48:c4:74:25:4b:26:dd
                                            C:1 A:0 T:0 00:11:00:00
  0x20   5369      Online  f60004202091     C:1 A:0 T:3 60:06:01:60:88:02:a8:2b
                                                        ba:18:6a:40:22:40:94:75
                                            C:1 A:0 T:0 00:20:00:00
  0x21   3221      Online  f60004202091     C:1 A:0 T:3 60:06:01:60:88:02:a8:2b
                                                        74:d2:42:9e:31:8d:ff:86
                                            C:1 A:0 T:0 00:21:00:00

canterbury#show interface iscsi 2/1

iscsi2/1 is up
    Hardware is GigabitEthernet
    Port WWN is 20:41:00:0c:30:6c:24:40
    Admin port mode is ISCSI
    Port mode is ISCSI
    Speed is 1 Gbps
    iSCSI initiator is identified by name
    Number of iSCSI session: 4, Number of TCP connection: 4
    Configured TCP parameters
        Local Port is 3260
        PMTU discover is enabled, reset timeout is 3600 sec
        Keepalive-timeout is 60 sec
        Minimum-retransmit-time is 300 ms
        Max-retransmissions 4
        Sack is disabled
        Maximum allowed bandwidth is 800000 kbps
        Minimum available bandwidth is 800000 kbps
        Estimated round trip time is 100000 usec
    5 minutes input rate 168 bits/sec, 21 bytes/sec, 0 frames/sec
    5 minutes output rate 728 bits/sec, 91 bytes/sec, 0 frames/sec
    iSCSI statistics
      Input 12209 packets, 2668348 bytes
        Command 3282 pdus, Data-out 1038 pdus, 1989664 bytes
      Output 14762 packets, 3486596 bytes
        Response 3059 pdus (with sense 77), R2T 153 pdus
        Data-in 3215 pdus, 2744116 bytes

canterbury#show iscsi stats iscsi 2/1

iscsi2/1
    5 minutes input rate 168 bits/sec, 21 bytes/sec, 0 frames/sec
    5 minutes output rate 728 bits/sec, 91 bytes/sec, 0 frames/sec
    iSCSI statistics
      12209 packets input, 2668348 bytes
        Command 3282 pdus, Data-out 1038 pdus, 1989664 bytes, 0 fragments
      output 14762 packets, 3486596 bytes
        Response 3059 pdus (with sense 77), R2T 153 pdus
        Data-in 3215 pdus, 2744116 bytes

canterbury#show interface gigabitethernet 2/1

GigabitEthernet2/1 is up
    Hardware is GigabitEthernet, address is 0005.3000.ade6
    Internet address is 10.48.69.199/26
    MTU 2156  bytes
    Port mode is IPS
    Speed is 1 Gbps
    Beacon is turned off
    Auto-Negotiation is turned on
    iSCSI authentication: NONE
    5 minutes input rate 392 bits/sec, 49 bytes/sec, 0 frames/sec
    5 minutes output rate 64 bits/sec, 8 bytes/sec, 0 frames/sec
    126128 packets input, 12476013 bytes
      2 multicast frames, 0 compressed
      0 input errors, 0 frame, 0 overrun 0 fifo
    43443 packets output, 6256174 bytes, 0 underruns
      0 output errors, 0 collisions, 0 fifo
      0 carrier errors

canterbury#show ip route

Codes: C - connected, S - static

Gateway of last resort is 10.48.69.129

C 10.48.69.192/26 is directly connected, gigabitethernet2-1
C 10.48.69.128/26 is directly connected, mgmt0

Saída do Fabric Manager e do Device Manager

Esta seção fornece um exemplo de saída do MDS Fabric Manager 1.1(2) e do Device Manager 1.1.2.

Diagrama de Topologia do Fabric Manager

sn5428_solaris_2.gif

Esta é uma captura de tela de exemplo da exibição do Gerenciador de dispositivos 1.1(2) em canterbury.

sn5428_solaris_3.gif

  1. Selecione FC > LUNs na janela Gerenciador de dispositivos para exibir os pWWNs, IDs de LUN e a capacidade dos LUNs.

    sn5428_solaris_4.gif

  2. Selecione IP > iSCSI para exibir as sessões iSCSI.

    sn5428_solaris_5.gif

Informações Relacionadas

Histórico de revisões

Revisão Data de publicação Comentários
1.0
08-Oct-2018
Versão inicial

Este documento lhe foi útil?

FeedbackFeedback

Contate a Cisco

Este documento se refere a estes produtos