Exemplo de configuração de treinamento de linha do multiplexador de acesso DSL Huawei MA5600
Contents
Introduction
Este documento descreve as etapas mínimas de configuração necessárias no Multiplexador de Acesso de Linha de Assinante Digital (DSLAM - Digital Subscriber Line Access Multiplexer) do Huawei MA5600 para permitir que a Linha de Assinante Digital (VDSL - Digital Subscriber Line Access Multiplexer) de Taxa de Bits Muito Alta seja treinada no Cisco Customer Premise Equipment (CPE).
Prerequisites
Requirements
A Cisco recomenda que você atenda a estes requisitos antes de tentar esta configuração:
- Cabo firmemente conectado na porta VDSL do CPE e na porta correta no patch panel da DSLAM
- O CPE e a placa de linha/DSLAM devem estar funcionando
Componentes Utilizados
As informações neste documento são baseadas em um roteador Cisco 887VA que atua como um CPE e um Huwei 5600 DSLAM. No entanto, este documento não está restrito a versões específicas de software e hardware.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Background
Este documento tem como objetivo ajudar os engenheiros a configurar o Cisco CPE e um DSLAM Huawei em ambientes back-to-back/lab e entender os perfis básicos na extremidade do DSL do escritório central (CO).
Configurar
Conclua estas seções para configurar seu equipamento:
- Configuração do perfil de linha
- Configuração do perfil do canal
- Modelo de linha (combinação de perfil de linha e perfil de canal) Configuração
- Aplique o modelo de linha na respectiva porta DSLAM onde o CPE está conectado
Configuração do perfil de linha
- Verifique os perfis de linha já criados.
MA5600#display vdsl line-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl line-profile
------------------------------------------------------------------------------
Profile Profile Transmission
Index Name Mode
------------------------------------------------------------------------------
60 Test_vdsl VDSL (G993.2)
82 VDSL LINE PROFILE 82 VDSL (G993.2)
88 VDSL LINE PROFILE 88 VDSL (G993.2)
103 VDSL LINE PROFILE 103 VDSL (G993.2)
------------------------------------------------------------------------------
Total: 4 - Configure o perfil da linha.
MA5600#config
MA5600(config)#vdsl line-profile add 60
Failure: The profile has existed
MA5600(config)#vdsl line-profile add 61
Start adding profile
Press 'Q' to quit the current configuration and new configuration will be
> Do you want to name the profile (y/n) [n]:y
> Please input profile name:ZONE_TEST
> Transmission mode:
> 0: Custom
> 1: All (G992.1~5,T1.413,G993.2)
> 2: Full rate(G992.1/3/5,T1.413,G993.2)
> 3: G.DMT (G992.1/3/5,G993.2)
> 4: G.HS (G992.1~5,G993.2)
> 5: ADSL (G.992.1~5,T1.413)
> 6: VDSL (G993.2)
> Please select (0~6) [1]:6 >>>>>>>>>>>>>>>>>> Selecting Transmission Mode as VDSL
> Bit swap downstream 1-disable 2-enable (1~2) [2]:1
> Bit swap upstream 1-disable 2-enable (1~2) [2]:1
> Please select the form of transmit rate adaptation downstream:
> 1-fixed 2-adaptAtStartup 3-AdaptAtRuntime (1~3) [2]:
> Please select the form of transmit rate adaptation upstream:
> 1-fixed 2-adaptAtStartup 3-AdaptAtRuntime (1~3) [2]:
> Will you set SNR margin parameters? (y/n) [n]:
> Will you set DPBO parameters? (y/n)[n]:
> Will you set UPBO parameters? (y/n)[n]:
> Will you set RFI notch configuration parameter? (y/n) [n]:
> Will you set VDSL tone blackout configuration parameter? (y/n) [n]:
> Will you set mode-specific parameters? (y/n) [n]:
Add profile 61 successfully
MA5600#display vdsl line-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl line-profile
------------------------------------------------------------------------------
Profile Profile Transmission
Index Name Mode
------------------------------------------------------------------------------
60 Test_vdsl VDSL (G993.2)
61 ZONE_TEST VDSL (G993.2)
82 VDSL LINE PROFILE 82 VDSL (G993.2)
88 VDSL LINE PROFILE 88 VDSL (G993.2)
103 VDSL LINE PROFILE 103 VDSL (G993.2)
------------------------------------------------------------------------------
Total: 5
Configuração do perfil do canal
- Verifique os perfis de canal já criados.
MA5600#display vdsl channel-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl channel-profile
------------------------------------------------------------------------------
Profile Profile MinDw MaxDw MinUp MaxUp Data Path
Index Name Rate Rate Rate Rate Mode
------------------------------------------------------------------------------
60 test_vdsl 128 100000 128 100000 Both
99 VDSL CHANNEL PRO 128 100000 128 100000 PTM
FILE 99
------------------------------------------------------------------------------
Total: 2 - Configure o perfil do canal.
MA5600(config)#vdsl channel-profile add 60
Failure: The profile has existed
MA5600(config)#vdsl channel-profile add 61
Start adding profile
Press 'Q' to quit the current configuration and new configuration will be
neglected
> Do you want to name the profile (y/n) [n]:y
> Please input profile name:ZONE_TEST
> Data path mode 1-ATM, 2-PTM, 3-Both (1~3) [3]:2 >>>>>>>>>>>>>>>>>>>>>> PTM Mode
> Will you set the minimum impulse noise protection? (y/n) [n]:
> Will you set interleaving delay parameters? (y/n) [n]:
> Will you set parameters for rate? (y/n) [n]:
> Will you set rate thresholds? (y/n) [n]:
Add profile 61 successfully
MA5600#display vdsl channel-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl channel-profile
------------------------------------------------------------------------------
Profile Profile MinDw MaxDw MinUp MaxUp Data Path
Index Name Rate Rate Rate Rate Mode
------------------------------------------------------------------------------>
60 test_vdsl 128 100000 128 100000 Both
61 ZONE_TEST 128 100000 128 100000 PTM
99 VDSL CHANNEL PRO 128 100000 128 100000 PTM
FILE 99
------------------------------------------------------------------------------
Total: 3
Configuração do modelo de linha
- Verifique os modelos de linha já criados.
MA5600#display vdsl line-template
{ <cr>|template-index<U><1,128> }:
Command:
display vdsl line-template
------------------------------------------------------------------------------
Template Template Line Profile Channel1 Channnel2
Index Name Index Profile Index Profile Index
------------------------------------------------------------------------------
12 ios_test 10 11 -
16 DT-17a 18 18 -
17 profile_17a 17 17 -
18 aj_3M_US 17 5 -
60 VDSL LINE TEMPLA 60 60 -
TE 60
------------------------------------------------------------------------------
Total: 5 - Configure o modelo de linha.
MA5600(config)#vdsl line-template add 61
Start adding template
Press 'Q' to quit the current configuration and new configuration will be
neglected
> Do you want to name the template (y/n) [n]:y
> Please input template name:ZONE_TEST
> Please set the line-profile index (1~128) [1]:61 >>>>>>>>>>>>>>>>Line Profile
we added above
> Will you set channel configuration parameters? (y/n) [n]:y
> Please set the channel number (1~2) [1]:
> Channel1 configuration parameters:
> Please set the channel-profile index (1~128) [1]:61 >>>>>> Channel Profile
we added above
Add template 61 successfully
MA5600#display vdsl line-template
{ <cr>|template-index<U><1,128> }:
Command:
display vdsl line-template
------------------------------------------------------------------------------
Template Template Line Profile Channel1 Channnel2
Index Name Index Profile Index Profile Index
------------------------------------------------------------------------------
12 ios_test 10 11 -
16 DT-17a 18 18 -
17 profile_17a 17 17 -
18 aj_3M_US 17 5 -
60 VDSL LINE TEMPLA 60 60 -
TE 60
61 ZONE_TEST 61 61 -
------------------------------------------------------------------------------
Total: 6
Aplique o modelo de linha à porta DSLAM
Nesse caso, o CPE foi conectado à porta 0 do slot 5 do DSLAM Huawei.
MA5600(config)#display board 0
-------------------------------------------------------------------------
SlotID BoardName Status SubType0 SubType1
-------------------------------------------------------------------------
0 H563ADGE Failed
1 H565ADBF Normal >>>>>>>>>ADBF - Here 'A' means that this card supports ADSL
2 ADG Failed
3 H569SHEB Failed
4
5 H565VDBD Normal >>>> >>>>VDBD - Here 'V' means that this card supports VDSL
6
7 H561SCU Standby_normal O2FM >>>>>>>>>>>>>>>>>>>>>> Processor Cards
8 H561SCU Active_normal O2GS O2GS >>>>>>>>>>>>> Processor Cards
9
10
11 H565VDBD Failed
12 H569SHEB Failed
13
14 H561SHEA Failed
15
-------------------------------------------------------------------------
MA5600(config)#interface vdsl 0/5 (Board/ slot)
Check the port status: Status is deactivated and currently assigned to
Line Template 1 (default)
MA5600(config-if-vdsl-0/5)#display port state 0
-----------------------------------------------------------------
Port Status Loopback Line Template Alarm Template
-----------------------------------------------------------------
0 Deactivated Disable 1 1
-----------------------------------------------------------------
Atribuir modelo de linha (61) à porta (0/5/0)
MA5600(config-if-vdsl-0/5)#activate 0 template-index 61
>>>>>>>> We are already in board 0 slot 5, hence need to activate port 0 with
Line Template 61
MA5600(config-if-vdsl-0/5)#display port state 0
---------------------------------------------------------------
Port Status Loopback Line Template Alarm Template
---------------------------------------------------------------
0 Activating Disable 61 1 >>>>>Check the status
---------------------------------------------------------------
MA5600(config-if-vdsl-0/5)#display port state 0
-----------------------------------------------------------------
Port Status Loopback Line Template Alarm Template
---------------------------------------------------------------
0 Activated Disable 61 1 >>Status is activated
---------------------------------------------------------------
Verificar
Use esta seção para verificar a sua configuração.
A ferramenta Output Interpreter (exclusiva para clientes registrados) é compatível com alguns comandos de exibição.. Use a ferramenta Output Interpreter para visualizar uma análise do resultado gerado pelo comando show..
Verificação no DSLAM
Verifique os perfis de linha criados
MA5600#display vdsl line-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl line-profile
------------------------------------------------------------------------------
Profile Profile Transmission
Index Name Mode
------------------------------------------------------------------------------
60 Test_vdsl VDSL (G993.2)
61 ZONE_TEST VDSL (G993.2)
82 VDSL LINE PROFILE 82 VDSL (G993.2)
88 VDSL LINE PROFILE 88 VDSL (G993.2)
103 VDSL LINE PROFILE 103 VDSL (G993.2)
------------------------------------------------------------------------------
Total: 5
Verifique os perfis de canal criados
MA5600#display vdsl channel-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl channel-profile
------------------------------------------------------------------------------
Profile Profile MinDw MaxDw MinUp MaxUp Data Path
Index Name Rate Rate Rate Rate Mode
------------------------------------------------------------------------------
60 test_vdsl 128 100000 128 100000 Both
61 ZONE_TEST 128 100000 128 100000 PTM
99 VDSL CHANNEL PRO 128 100000 128 100000 PTM
FILE 99
------------------------------------------------------------------------------
Total: 3
Verifique os modelos de linha criados
MA5600#display vdsl line-template
{ <cr>|template-index<U><1,128> }:
Command:
display vdsl line-template
------------------------------------------------------------------------------
Template Template Line Profile Channel1 Channnel2
Index Name Index Profile Index Profile Index
------------------------------------------------------------------------------
12 ios_test 10 11 -
16 DT-17a 18 18 -
17 profile_17a 17 17 -
18 aj_3M_US 17 5 -
60 VDSL LINE TEMPLA 60 60 -
TE 60
61 ZONE_TEST 61 61 -
------------------------------------------------------------------------------
Total: 6
Verifique o status da porta DSLAM
Para isso, você precisa estar no modo de configuração de interface do DSLAM.
MA5600(config-if-vdsl-0/5)#display port state 0
-----------------------------------------------------------------
Port Status Loopback Line Template Alarm Template
-----------------------------------------------------------------
0 Activated Disable 61 1
-----------------------------------------------------------------
Verificação no CPE
Insira o comando show controller vdsl 0 no CPE para verificar o status do controlador.
/snip
C887VA-M#show controller vdsl 0
Controller VDSL 0 is UP
Daemon Status: Up
XTU-R (DS) XTU-C (US)
Chip Vendor ID: 'BDCM' 'BDCM'
Chip Vendor Specific: 0x0000 0x939B
Chip Vendor Country: 0xB500 0xB500
Modem Vendor ID: 'CSCO' ' '
Modem Vendor Specific: 0x4602 0x0000
Modem Vendor Country: 0xB500 0x0000
Serial Number Near: FTX162580HZ 887VA-M 15.2(4)M
Serial Number Far:
Modem Version Near: 15.2(4)M
Modem Version Far: 0x939b
Modem Status: TC Sync (Showtime!)
DSL Config Mode: AUTO
Trained Mode: G.993.2 (VDSL2) Profile 12a
TC Mode: PTM
Troubleshoot
Atualmente, não existem informações disponíveis específicas sobre Troubleshooting para esta configuração.
Informações Relacionadas
Histórico de revisões
| Revisão | Data de publicação | Comentários |
|---|---|---|
1.0 |
01-Dec-2014 |
Versão inicial |
FeedbackContate a Cisco
- Abrir um caso de suporte
- (É necessário um Contrato de Serviço da Cisco)