Contents

Introduction

Prerequisites

Requirements

Componentes Utilizados

Conventions

Configuração

Comandos VoIP

show voice port summary

show voice call summary

show dial-peer voice summary

show call ative voice brief

show voice dsp

Appendix

Informações Relacionadas

Introduction

Este documento aborda os objetos MIB equivalentes que fornecem as informações contidas em vários comandos de verificação de Voz sobre IP (VoIP). Os aplicativos e/ou scripts NMS podem potencialmente usar essas informações.

Prerequisites

Requirements

Não existem requisitos específicos para este documento.

Componentes Utilizados

Este documento não está restrito a versões de software específicas. No entanto, ele foi criado especificamente para um Cisco 3600 Series Router com uma placa NM-2V.

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Conventions

For more information on document conventions, refer to the Cisco Technical Tips Conventions.

Configuração

Esta saída mostra uma parte relevante da configuração que este documento usa:

VoipRouter#show running-configuration

Building configuration...

Current configuration : 5412 bytes

!

version 12.3

...

!

snmp-server community public RO

!

...

!

voice-port 2/0/0

!

...

!

dial-peer voice 2000 pots

destination-pattern 2000

port 2/0/0

!

dial-peer voice 1000 voip

destination-pattern 1000

session target ipv4:172.16.99.22

!

...

end

Comandos VoIP

Estas seções mostram os objetos MIB que correspondem à saída destes comandos de verificação de VoIP:

- show voice port summary (somente para placa NM-2V)

- show voice call summary

- show dial-peer voice summary

- show call ative voice brief (somente para a plataforma Cisco 3600)

- show voice dsp (somente para placa NM-HDV)

As informações que esses comandos de verificação de VoIP contêm podem ser extraídas de IF-MIB, CISCO-VOICE-IF-MIB, CISCO-VOICE-ANALOG-IF-MIB, CISCO-VOICE-DIAL-CONTROL-MIB, DIAL-CONTROL-MIB e CISCO-DSP-MGMT MIB.

Observação: nesses exemplos, o trecho de Telefonia é indexado por 1102799 e o trecho H.323 é indexado por 1102966.

show voice port summary

Observação: o texto em negrito no comando show voice port summary é descrito na seção Objetos MIB equivalentes.

VoipRouter#show voice port summary

IN           OUT

PORT      CH   SIG-TYPE   ADMIN OPER  STATUS       STATUS   EC

========= == ============ ===== ====  ========     ======== ==

2/0/0(A1) --  fxs-ls(A2)  up(A3)up(A4) off-hook(A5) idle     y(A6)

2/0/1     --  fxs-ls      up    dorm   on-hook      idle     y

Objetos MIB equivalentes

A1  —  IF-MIB::ifDescr.37 = STRING: Foreign Exchange Station 2/0/0

A2  —  CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSCfgSignalType.37 = INTEGER: fxsLoopStart(1)

A3  —  IF-MIB::ifAdminStatus.37 = INTEGER: up(1)

A4  —  IF-MIB::ifOperStatus.37 = INTEGER: up(1)

A5  —  CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSHookStatus.37 = INTEGER: offHook(2)

A6  —  CISCO-VOICE-IF-MIB::cvIfCfgEchoCancelEnable.37 = INTEGER: true(1)

Observação: Nenhum objeto MIB mantém o valor contido na parte CH do comando show voice port summary quando a placa NM-2V é usada.

show voice call summary

Observação: o texto em negrito no comando show voice call summary é descrito na seção Objetos MIB equivalentes.

VoipRouter#show voice call summary

PORT         CODEC      VAD   VTSP STATE            VPM STATE

============ ========   ===   ==================== ======================

2/0/0(B1)    g729r8(B2) y(B3) S_CONNECT             FXSLS_CONNECT

2/0/1         -         -       -                   FXSLS_ONHOOK

Objetos MIB equivalentes

B1  —  IF-MIB::ifDescr.37 = STRING: Foreign Exchange Station 2/0/0

B2  —  CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveCoderTypeRate.

1102966.1 = INTEGER: ietfg729r8000(25)

B3  —  CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveVADEnable.

1102966.1 = INTEGER: true(1)

Observação: nenhum objeto MIB mantém os estados do Voice Telephony Service Provider (VTSP) e do VPM individualmente. Use callAtiveCallState de DIAL-CONTROL-MIB em vez disso.

show dial-peer voice summary

Observação: o texto em negrito no comando show dial-peer voice summary é descrito na seção Objetos MIB equivalentes.

VoipRouter#show dial-peer voice summary

dial-peer hunt 0

AD                                        PRE  PASS

TAG      TYPE     MIN     OPER    PREFIX DEST-PATTERN  FER  THRU SESS-TARGET   PORT

2000(C1) pots(C2)  up(C3)  up(C4) 9(C5)   2000(C6)     0(C7)                2/0/0(C8)

1000     voip      up      up             1000         0    syst ipv4:172.16.99.22(C9)

Objetos MIB equivalentes

C1  —  CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgIfIndex.2000 = INTEGER: 90

—  DIAL-CONTROL-MIB::dialCtlPeerCfgLowerIf.2000.90 = INTEGER: 37

C2  —  CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgType.2000 = INTEGER: voice(1)

C3  —  IF-MIB::ifAdminStatus.37 = INTEGER: up(1)

C4  —  IF-MIB::ifOperStatus.37 = INTEGER: up(1)

C5  —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgDialDigitsPrefix.90 = STRING: 9

C6  —  DIAL-CONTROL-MIB::dialCtlPeerCfgOriginateAddress.2000.90 = STRING: 2000

C7  —  CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgPreference.90 = INTEGER: 0

C8  —  IF-MIB::ifDescr.37 = STRING: Foreign Exchange Station 2/0/0

C9  —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgSessionTarget.91 =

STRING: ipv4:172.16.99.22

Observação: Nenhum objeto MIB mantém o valor contido na parte do método PASS THRU do modem do comando show dial-peer summary.

show call ative voice brief

Observação: o texto em negrito no comando show call ative voice brief é descrito na seção Objetos MIB equivalentes.

VoIPRouter#show call active voice brief

<ID>:<start>hs.<index> +<connect> pid:<peer_id> <dir> <addr> <state>

dur hh:mm:ss tx:<packets>/<bytes> rx:<packets>/<bytes>

IP <ip>:<udp> rtt:<time>ms pl:<play>/<gap>ms lost:<lost>/<early>/<late>

delay:<last>/<min>/<max>ms <codec>

MODEMPASS <method> buf:<fills>/<drains> loss <overall%>

<multipkt>/<corrected>

last <buf event time>s dur:<Min>/<Max>s

FR <protocol> [int dlci cid] vad:<y/n> dtmf:<y/n> seq:<y/n>

sig:<on/off> <codec> (payload size)

ATM <protocol> [int vpi/vci cid] vad:<y/n> dtmf:<y/n> seq:<y/n>

sig:<on/off> <codec> (payload size)

Tele <int>:tx:<tot>/<v>/<fax>ms <codec> noise:<l> acom:<l> i/o:<l>/<l>

dBm

MODEMRELAY info:<rcvd>/<sent>/<resent> xid:<rcvd>/<sent>

total:<rcvd>/<sent>/<drops>

Proxy <ip>:<audio udp>,<video udp>,<tcp0>,<tcp1>,<tcp2>,<tcp3> endpt:

<type>/<manf>

bw:<req>/<act> codec:<audio>/<video>

tx:<audio pkts>/<audio bytes>,<video pkts>/<video bytes>,<t120

pkts>/<t120 bytes>

rx:<audio pkts>/<audio bytes>,<video pkts>/<video bytes>,<t120

pkts>/<t120 bytes>

Telephony call-legs: 1

SIP call-legs: 0

H323 call-legs: 1

MGCP call-legs: 0

Total call-legs: 2

11D9 : 1102799(D1)hs.1 +1324 pid:2000(D2) Answer(D3) 2000(D4) active(D5)

dur 1d19h(D6) tx:7875641(D7)/157512782(D8) rx:7875955(D9)/157519081(D10)

Tele 2/0/0(D11):1: tx:157515460(D12)/157514630(D13)/0ms g729r8(D14)

noise:-56(D15) acom:5(D16)  i/0:-40(D17)/-46(D18) dBm

11D9 : 1102966hs.1 +1157 pid:1000 Originate 1000 active

dur 1d19h tx:7875388/157507741 rx:7875641/157512782

IP 172.16.99.22(D19):19066(D20) rtt:6ms(D21) pl:157496940(D22)/4770ms(D23)

lost:52(D24)/1(D25)/325(D26) delay:67(D27)/55(D28)/132ms(D29) g729r8

Telephony call-legs: 1

SIP call-legs: 0

H323 call-legs: 1

MGCP call-legs: 0

Total call-legs: 2

Objetos MIB equivalentes

D1  —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveConnectionId.1102799.1

= Hex-STRING: 53 98 B1 3F EB B7 11 D7 80 02 AA AD C2 77 19 FC

D2  —  DIAL-CONTROL-MIB::callActivePeerId.1102799.1 = INTEGER: 2000

D3  —  DIAL-CONTROL-MIB::callActiveCallOrigin.1102799.1 = INTEGER: answer(2)

D4  —  DIAL-CONTROL-MIB::callActivePeerAddress.1102799.1 = STRING: 2000

D5  —  DIAL-CONTROL-MIB::callActiveCallState.1102799.1 = INTEGER: active(4)

D6  —  DIAL-CONTROL-MIB::callActiveConnectTime.1102799.1 = Timeticks:

(1104123) 3:04:01.23

—  DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (16590203) 1 days,

22:05:02.03

D7  —  DIAL-CONTROL-MIB::callActiveTransmitPackets.1102799.1 = Gauge32: 7875641

D8  —  DIAL-CONTROL-MIB::callActiveTransmitBytes.1102799.1 = Gauge32: 157512782

D9  —  DIAL-CONTROL-MIB::callActiveReceivePackets.1102799.1 = Gauge32: 7875955

D10 —  DIAL-CONTROL-MIB::callActiveReceiveBytes.1102799.1 = Gauge32: 157519081

D11 —  IF-MIB::ifDescr.37 = STRING: Foreign Exchange Station 2/0/0

D12 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveTxDuration.

1102799.1 = Gauge32: 157515460 milliseconds

D13 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveVoiceTxDuration.

1102799.1 = Gauge32: 157514630 milliseconds

D14 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveCoderTypeRate.

1102799.1 = INTEGER: ietfg729r8000(25)

D15 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveNoiseLevel.

1102799.1 = INTEGER: -56 dBm

D16 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveACOMLevel.

1102799.1 =  INTEGER: 5 dB

D17 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveInSignalLevel.

1102799.1 = INTEGER: -40 dBm

D18 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveOutSignalLevel.

1102799.1 = INTEGER: -46 dBm

D19 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRemoteIPAddress.

1102966.1 = IpAddress: 172.16.99.22

D20 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRemoteUDPPort.

1102966.1 = INTEGER: 19066

D21 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRoundTripDelay.

1102966.1 = Gauge32: 6 milliseconds

D22 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveOnTimeRvPlayout.

1102966.1 = Gauge32: 157496940 milliseconds

D23 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithSilence.

1102966.1 = Gauge32: 1090 milliseconds

—  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithPrediction.

1102966.1 = Gauge32: 3680 milliseconds

—  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithInterpolation.

1102966.1 = Gauge32: 0 milliseconds

D24 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLostPackets.

1102966.1 = Gauge32: 52 packets

D25 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEarlyPackets.

1102966.1 = Gauge32: 1 packets

D26 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLatePackets.

1102966.1 = Gauge32: 325 packets

D27 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveReceiveDelay.

1102966.1 = Gauge32: 67

D28 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLoWaterPlayoutDelay.

1102966.1 = Gauge32: 55 milliseconds

D29 —  CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveHiWaterPlayoutDelay.

1102966.1 = Gauge32: 132 milliseconds

Observação: o valor de GapFill do comando show call ative voice brief é obtido quando você adiciona os Objetos SNMP cvVoIPCallAtiveGapFillWithSilence, cvVoIPCallAtiveGapFillWithPredication e cvVoIPCallAtiveGapFap InterpolaçãoInoperante.

show voice dsp

VoIPRouter#show voice dsp

DSP  DSP             DSPWARE CURR  BOOT                         PAK     TX/RX

TYPE NUM CH CODEC    VERSION STATE STATE   RST AI VOICEPORT TS ABORT  PACK COUNT

==== === == ======== ======= ===== ======= === == ========= == ===== ============

C549 009 01 {medium}  4.1.31 IDLE  idle      0  0 1/0:0     05     0         0/36

02 {medium}  4.1.31 IDLE  idle         0 1/0:0     06     0          0/0

03 {medium}  4.1.31 IDLE  idle         0 1/0:0     07     0          0/0

04 {medium}  4.1.31 IDLE  idle         0 1/0:0     08     0          0/0

C549 010 01 {medium}  4.1.31 IDLE  idle      0  0 1/0:0     09     0          0/0

02 {medium}  4.1.31 IDLE  idle         0 1/0:0     10     0          0/0

03 {medium}  4.1.31 IDLE  idle         0 1/0:0     11     0          0/0

04 {medium}  4.1.31 IDLE  idle         0 1/0:0     12     0          0/0

C549 011 01 {medium}  4.1.31 IDLE  idle      0  0 1/0:0     13     0          0/0

02 {medium}  4.1.31 IDLE  idle         0 1/0:0     14     0          0/0

03 {medium}  4.1.31 IDLE  idle         0 1/0:0     15     0          0/0

04 {medium}  4.1.31 IDLE  idle         0 1/0:0     16     0          0/0

C549 012 01 {medium}  4.1.31 IDLE  idle      0  0 1/0:0     17     0          0/0

02 {medium}  4.1.31 IDLE  idle         0 1/0:0     18     0          0/0

03 {medium}  4.1.31 IDLE  idle         0 1/0:0     19     0          0/0

04 {medium}  4.1.31 IDLE  idle         0 1/0:0     20     0          0/0

C549 013 01 {medium}  4.1.31 IDLE  idle      0  0 1/0:0     21     0          0/0

02 {medium}  4.1.31 IDLE  idle         0 1/0:0     22     0          0/0

03 {medium}  4.1.31 IDLE  idle         0 1/0:0     23     0         0/12

04 g729r8    4.1.31 busy  idle         0 1/0:0     24     0    176/56702

C549 014 01 {medium}  4.1.31 IDLE  idle      0  0 1/0:0     01     0         0/27

02 {medium}  4.1.31 IDLE  idle         0 1/0:0     02     0         0/12

03 {medium}  4.1.31 IDLE  idle         0 1/0:0     03     0         0/12

04 {medium}  4.1.31 IDLE  idle         0 1/0:0     04     0         0/12

Aqui estão alguns objetos MIB úteis que fornecem informações sobre a chamada ativa na saída do exemplo do comando show voice dsp:

CISCO-DSP-MGMT-MIB::cdspCardIndex.7 = INTEGER: 2

OLD-CISCO-CHASSIS-MIB::cardType.2 = INTEGER: hdv(516)

OLD-CISCO-CHASSIS-MIB::cardDescr.2 = STRING: "High Density Voice"

ENTITY-MIB::entPhysicalDescr.7 = STRING: High Density Voice

ENTITY-MIB::entPhysicalDescr.22 = STRING: DSP (C549)

CISCO-DSP-MGMT-MIB::cdspCardState.7 = INTEGER: normal(1)

CISCO-DSP-MGMT-MIB::cdspCardMaxChanPerDSP.7 = Gauge32: 4 channels

CISCO-DSP-MGMT-MIB::cdspTotalChannels.22 = Gauge32: 4 channels

CISCO-DSP-MGMT-MIB::cdspActiveChannels.21 = Gauge32: 1 channels

Observação: o MIB que contém as informações para show voice dsp é CISCO-DSP-MGMT-MIB. No entanto, devido ao bug da Cisco ID CSCeb62542 para a placa NM-2V, os DSPs em NM-2V não são mostrados em ENTITY-MIB. Como cdspCardStatusTable depende de entPhysicalIndex de ENTITY-MIB, cdspCardStatusTable não é preenchido para a placa NM-2V.

Appendix

Esta saída mostra o snmpwalk completo de ciscoVoiceAnalogIfMIB de CISCO-VOICE-ANALOG-IF-MIB no momento dos comandos de verificação de VoIP mostrados neste documento:

snmpwalk -c public 172.16.100.20 CISCO-VOICE-ANALOG-IF-MIB:ciscoVoiceAnalogIfMIB

CISCO-VOICE-ANALOG-IF-MIB::cvaIfCfgImpedance.37 = INTEGER: ohms600Real(2)

CISCO-VOICE-ANALOG-IF-MIB::cvaIfCfgImpedance.38 = INTEGER: ohms600Real(2)

CISCO-VOICE-ANALOG-IF-MIB::cvaIfCfgIntegratedDSP.37 = INTEGER: false(2)

CISCO-VOICE-ANALOG-IF-MIB::cvaIfCfgIntegratedDSP.38 = INTEGER: false(2)

CISCO-VOICE-ANALOG-IF-MIB::cvaIfStatusInfoType.37 = INTEGER: voice(2)

CISCO-VOICE-ANALOG-IF-MIB::cvaIfStatusInfoType.38 = INTEGER: none(1)

CISCO-VOICE-ANALOG-IF-MIB::cvaIfMaintenanceMode.37 = INTEGER: none(1)

CISCO-VOICE-ANALOG-IF-MIB::cvaIfMaintenanceMode.38 = INTEGER: none(1)

CISCO-VOICE-ANALOG-IF-MIB::cvaIfStatusSignalErrors.37 = Counter32: 0

CISCO-VOICE-ANALOG-IF-MIB::cvaIfStatusSignalErrors.38 = Counter32: 0

CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSCfgSignalType.37 = INTEGER: fxsLoopStart(1)

CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSCfgSignalType.38 = INTEGER: fxsLoopStart(1)

CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingFrequency.37 = INTEGER: ringFrequency25(1)

CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingFrequency.38 = INTEGER: ringFrequency25(1)

CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSHookStatus.37 = INTEGER: offHook(2)

CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSHookStatus.38 = INTEGER: onHook(1)

CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingActive.37 = INTEGER: false(2)

CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingActive.38 = INTEGER: false(2)

CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingGround.37 = INTEGER: false(2)

CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingGround.38 = INTEGER: false(2)

CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTipGround.37 = INTEGER: false(2)

CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTipGround.38 = INTEGER: false(2)

CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTimingDigitDuration.37 =

INTEGER: 100 milliseconds

CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTimingDigitDuration.38 =

INTEGER: 100 milliseconds

CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTimingInterDigitDuration.37 =

INTEGER: 100 milliseconds

CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTimingInterDigitDuration.38 =

INTEGER: 100 milliseconds

Esta saída mostra o snmpwalk completo de ciscoVoiceInterfaceMIB de CISCO-VOICE-IF-MIB no momento dos comandos de verificação de VoIP mostrados neste documento:

snmpwalk -c public 172.16.100.20 CISCO-VOICE-IF-MIB:ciscoVoiceInterfaceMIB

CISCO-VOICE-IF-MIB::cvIfCfgNoiseRegEnable.37 = INTEGER: true(1)

CISCO-VOICE-IF-MIB::cvIfCfgNoiseRegEnable.38 = INTEGER: true(1)

CISCO-VOICE-IF-MIB::cvIfCfgNonLinearProcEnable.37 = INTEGER: true(1)

CISCO-VOICE-IF-MIB::cvIfCfgNonLinearProcEnable.38 = INTEGER: true(1)

CISCO-VOICE-IF-MIB::cvIfCfgMusicOnHoldThreshold.37 = INTEGER: -38 dBm

CISCO-VOICE-IF-MIB::cvIfCfgMusicOnHoldThreshold.38 = INTEGER: -38 dBm

CISCO-VOICE-IF-MIB::cvIfCfgInGain.37 = INTEGER: 0 dB

CISCO-VOICE-IF-MIB::cvIfCfgInGain.38 = INTEGER: 0 dB

CISCO-VOICE-IF-MIB::cvIfCfgOutAttn.37 = INTEGER: 3 dB

CISCO-VOICE-IF-MIB::cvIfCfgOutAttn.38 = INTEGER: 3 dB

CISCO-VOICE-IF-MIB::cvIfCfgEchoCancelEnable.37 = INTEGER: true(1)

CISCO-VOICE-IF-MIB::cvIfCfgEchoCancelEnable.38 = INTEGER: true(1)

CISCO-VOICE-IF-MIB::cvIfCfgEchoCancelCoverage.37 = INTEGER: 4

CISCO-VOICE-IF-MIB::cvIfCfgEchoCancelCoverage.38 = INTEGER: 4

CISCO-VOICE-IF-MIB::cvIfCfgConnectionMode.37 = INTEGER: normal(1)

CISCO-VOICE-IF-MIB::cvIfCfgConnectionMode.38 = INTEGER: normal(1)

CISCO-VOICE-IF-MIB::cvIfCfgConnectionNumber.37 = STRING:

CISCO-VOICE-IF-MIB::cvIfCfgConnectionNumber.38 = STRING:

CISCO-VOICE-IF-MIB::cvIfCfgInitialDigitTimeOut.37 = INTEGER: 10 seconds

CISCO-VOICE-IF-MIB::cvIfCfgInitialDigitTimeOut.38 = INTEGER: 10 seconds

CISCO-VOICE-IF-MIB::cvIfCfgInterDigitTimeOut.37 = INTEGER: 10 seconds

CISCO-VOICE-IF-MIB::cvIfCfgInterDigitTimeOut.38 = INTEGER: 10 seconds

CISCO-VOICE-IF-MIB::cvIfCfgRegionalTone.37 = STRING: "US"

CISCO-VOICE-IF-MIB::cvIfCfgRegionalTone.38 = STRING: "US"

CISCO-VOICE-IF-MIB::cvIfCfgEntry.13.37 = INTEGER: 1

CISCO-VOICE-IF-MIB::cvIfCfgEntry.13.38 = INTEGER: 1

CISCO-VOICE-IF-MIB::cvIfCfgEntry.14.37 = INTEGER: 1

CISCO-VOICE-IF-MIB::cvIfCfgEntry.14.38 = INTEGER: 1

Esta saída mostra o snmpwalk completo de ciscoVoiceDialControlMIB de CISCO-VOICE-DIAL-CONTROL-MIB no momento dos comandos de verificação de VoIP mostrados neste documento:

snmpwalk -c public 172.16.100.20 CISCO-VOICE-DIAL-CONTROL-MIB:ciscoVoiceDialControlMIB

CISCO-VOICE-DIAL-CONTROL-MIB::cvGeneralPoorQoVNotificationEnable.0 = INTEGER: true(1)

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgIfIndex.1000 = INTEGER: 91

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgIfIndex.2000 = INTEGER: 90

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgType.1000 = INTEGER: voip(2)

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgType.2000 = INTEGER: voice(1)

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgRowStatus.1000 = INTEGER: active(1)

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgRowStatus.2000 = INTEGER: active(1)

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgEntry.5.1000 = INTEGER: 1

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgEntry.5.2000 = INTEGER: 1

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgSessionTarget.90 = STRING:

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgDialDigitsPrefix.90 = STRING: 9

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgDIDCallEnable.90 = INTEGER: false(2)

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgCasGroup.90 = INTEGER: -1

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgRegisterE164.90 = INTEGER: true(1)

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgForwardDigits.90 = INTEGER: -1

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgEntry.7.90 = INTEGER: 1

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgSessionProtocol.91 = INTEGER: cisco(2)

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgDesiredQoS.91 = INTEGER: 1

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgMinAcceptableQoS.91 = INTEGER: 1

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgSessionTarget.91 =

STRING: ipv4:172.16.99.22

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgCoderRate.91 =

INTEGER: g729IETFr8000(16)

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgFaxRate.91 = INTEGER: voiceRate(2)

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgVADEnable.91 = INTEGER: true(1)

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgExpectFactor.91 =

INTEGER: 0 equipment impairment factor (eif)

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgIcpif.91 =

INTEGER: 20 equipment impairment factor (eif)

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgPoorQoVNotificationEnable.91 =

INTEGER: false(2)

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgUDPChecksumEnable.91 = INTEGER: false(2)

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgIPPrecedence.91 = INTEGER: 0

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgTechPrefix.91 = STRING:

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgDigitRelay.91 = Hex-STRING: 00

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgCoderBytes.91 = INTEGER: 20 bytes

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgFaxBytes.91 = INTEGER: 20 bytes

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgInBandSignaling.91 = INTEGER: cas(1)

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgEntry.23.91 = INTEGER: 1

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgIncomingDnisDigits.90 = STRING:

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgIncomingDnisDigits.91 = STRING:

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgMaxConnections.90 =

INTEGER: -1 connections

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgMaxConnections.91 =

INTEGER: -1 connections

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgApplicationName.90 = STRING:

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgApplicationName.91 = STRING:

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgPreference.90 = INTEGER: 0

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgPreference.91 = INTEGER: 0

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgHuntStop.90 = INTEGER: false(2)

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgHuntStop.91 = INTEGER: false(2)

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.6.90 = ""

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.6.91 = ""

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.7.90 = ""

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.7.91 = ""

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.8.90 = ""

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.8.91 = ""

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.9.90 = ""

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.9.91 = ""

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.10.90 = ""

CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.10.91 = ""

CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveConnectionId.1102799.1 =

Hex-STRING: 53 98 B1 3F EB B7 11 D7 80 02 AA AD C2 77 19 FC

CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveTxDuration.1102799.1 =

Gauge32: 157515460 milliseconds

CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveVoiceTxDuration.1102799.1 =

Gauge32: 157514630 milliseconds

CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveFaxTxDuration.1102799.1 =

Gauge32: 0 milliseconds

CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveCoderTypeRate.1102799.1 =

INTEGER: ietfg729r8000(25)

CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveNoiseLevel.1102799.1 = INTEGER: -56 dBm

CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveACOMLevel.1102799.1 = INTEGER: 5 dB

CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveOutSignalLevel.1102799.1 =

INTEGER: -46 dBm

CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveInSignalLevel.1102799.1 =

INTEGER: -40 dBm

CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveERLLevel.1102799.1 = INTEGER: 5 dB

CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveSessionTarget.1102799.1 = STRING:

CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveImgPageCount.1102799.1 = Gauge32: 0 pages

CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveEntry.13.1102799.1 = ""

CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveEntry.14.1102799.1 = INTEGER: 2

CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveEntry.15.1102799.1 = INTEGER: 19971

CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveEntry.17.1102799.1 = INTEGER: 5

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveConnectionId.1102966.1 =

Hex-STRING: 53 98 B1 3F EB B7 11 D7 80 02 AA AD C2 77 19 FC

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRemoteIPAddress.1102966.1 =

IpAddress: 172.16.99.22

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRemoteUDPPort.1102966.1 =

INTEGER: 19066

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRoundTripDelay.1102966.1 =

Gauge32: 6 milliseconds

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveSelectedQoS.1102966.1 = INTEGER: 1

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveSessionProtocol.1102966.1 =

INTEGER: cisco(2)

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveSessionTarget.1102966.1 =

STRING: ipv4:172.16.99.22

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveOnTimeRvPlayout.1102966.1 =

Gauge32: 157496940 milliseconds

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithSilence.1102966.1 =

Gauge32: 1090 milliseconds

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithPrediction.1102966.1 =

Gauge32: 3680 milliseconds

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithInterpolation.1102966.1 =

Gauge32: 0 milliseconds

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithRedundancy.1102966.1 =

Gauge32: 0 milliseconds

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveHiWaterPlayoutDelay.1102966.1 =

Gauge32: 132 milliseconds

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLoWaterPlayoutDelay.1102966.1 =

Gauge32: 55 milliseconds

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveReceiveDelay.1102966.1 =

Gauge32: 67

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveVADEnable.1102966.1 =

INTEGER: true(1)

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveCoderTypeRate.1102966.1 =

INTEGER: ietfg729r8000(25)

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLostPackets.1102966.1 =

Gauge32: 52 packets

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEarlyPackets.1102966.1 =

Gauge32: 1 packets

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLatePackets.1102966.1 =

Gauge32: 325 packets

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.21.1102966.1 = ""

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.22.1102966.1 = ""

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.23.1102966.1 = INTEGER: 1

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.24.1102966.1 =

STRING: "172.16.99.22"

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.25.1102966.1 = INTEGER: 1720

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.26.1102966.1 = INTEGER: 1

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.27.1102966.1 =

STRING: "172.16.99.22"

CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.28.1102966.1 = INTEGER: 19066

Esta saída mostra o snmpwalk completo de ciscoVoiceCommonDialControlMIB de CISCO-VOICE-DIAL-CONTROL-MIB no momento dos comandos de verificação de VoIP mostrados neste documento:

snmpwalk -c public 172.16.100.20 CISCO-VOICE-COMMON-DIAL-CONTROL-MIB:

ciscoVoiceCommonDialControlMIB

CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveConnectionId.

1102966.1 = Hex-STRING: 53 98 B1 3F EB B7 11 D7 80 02 AA AD C2 77 19 FC

CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveVADEnable.

1102966.1 = INTEGER: true(1)

CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveCoderTypeRate.

1102966.1 = INTEGER: ietfg729r8000(25)

CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveCodecBytes.

1102966.1 = INTEGER: 20

CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveInBandSignaling.

1102966.1 = INTEGER: cas(1)

CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveEntry.6.

1102966.1 = ""

CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveEntry.7.

1102966.1 = INTEGER: 2

Esta saída mostra o snmpwalk completo de dialControlMib de DIAL-CONTROL-MIB no momento dos comandos de verificação de VoIP mostrados neste documento:

snmpwalk -c public 172.16.100.20 DIAL-CONTROL-MIB:dialControlMib

DIAL-CONTROL-MIB::dialCtlAcceptMode.0 = INTEGER: acceptAll(2)

DIAL-CONTROL-MIB::dialCtlTrapEnable.0 = INTEGER: enabled(1)

DIAL-CONTROL-MIB::dialCtlPeerCfgIfType.1000.91 = INTEGER: voiceOverIp(104)

DIAL-CONTROL-MIB::dialCtlPeerCfgIfType.2000.90 = INTEGER: voiceFXS(102)

DIAL-CONTROL-MIB::dialCtlPeerCfgLowerIf.1000.91 = INTEGER: 0

DIAL-CONTROL-MIB::dialCtlPeerCfgLowerIf.2000.90 = INTEGER: 37

DIAL-CONTROL-MIB::dialCtlPeerCfgOriginateAddress.1000.91 = STRING: 1000

DIAL-CONTROL-MIB::dialCtlPeerCfgOriginateAddress.2000.90 = STRING: 2000

DIAL-CONTROL-MIB::dialCtlPeerCfgAnswerAddress.1000.91 = STRING:

DIAL-CONTROL-MIB::dialCtlPeerCfgAnswerAddress.2000.90 = STRING:

DIAL-CONTROL-MIB::dialCtlPeerCfgSubAddress.1000.91 = STRING:

DIAL-CONTROL-MIB::dialCtlPeerCfgSubAddress.2000.90 = STRING:

DIAL-CONTROL-MIB::dialCtlPeerCfgSpeed.1000.91 = INTEGER: 0

DIAL-CONTROL-MIB::dialCtlPeerCfgSpeed.2000.90 = INTEGER: 0

DIAL-CONTROL-MIB::dialCtlPeerCfgInfoType.1000.91 = INTEGER: speech(2)

DIAL-CONTROL-MIB::dialCtlPeerCfgInfoType.2000.90 = INTEGER: speech(2)

DIAL-CONTROL-MIB::dialCtlPeerCfgPermission.1000.91 = INTEGER: both(3)

DIAL-CONTROL-MIB::dialCtlPeerCfgPermission.2000.90 = INTEGER: both(3)

DIAL-CONTROL-MIB::dialCtlPeerCfgInactivityTimer.1000.91 = INTEGER: 0 seconds

DIAL-CONTROL-MIB::dialCtlPeerCfgInactivityTimer.2000.90 = INTEGER: 0 seconds

DIAL-CONTROL-MIB::dialCtlPeerCfgMinDuration.1000.91 = INTEGER: 0

DIAL-CONTROL-MIB::dialCtlPeerCfgMinDuration.2000.90 = INTEGER: 0

DIAL-CONTROL-MIB::dialCtlPeerCfgMaxDuration.1000.91 = INTEGER: 0

DIAL-CONTROL-MIB::dialCtlPeerCfgMaxDuration.2000.90 = INTEGER: 0

DIAL-CONTROL-MIB::dialCtlPeerCfgCarrierDelay.1000.91 = INTEGER: 0 seconds

DIAL-CONTROL-MIB::dialCtlPeerCfgCarrierDelay.2000.90 = INTEGER: 0 seconds

DIAL-CONTROL-MIB::dialCtlPeerCfgCallRetries.1000.91 = INTEGER: 0

DIAL-CONTROL-MIB::dialCtlPeerCfgCallRetries.2000.90 = INTEGER: 0

DIAL-CONTROL-MIB::dialCtlPeerCfgRetryDelay.1000.91 = INTEGER: 0 seconds

DIAL-CONTROL-MIB::dialCtlPeerCfgRetryDelay.2000.90 = INTEGER: 0 seconds

DIAL-CONTROL-MIB::dialCtlPeerCfgFailureDelay.1000.91 = INTEGER: 0 seconds

DIAL-CONTROL-MIB::dialCtlPeerCfgFailureDelay.2000.90 = INTEGER: 0 seconds

DIAL-CONTROL-MIB::dialCtlPeerCfgTrapEnable.1000.91 = INTEGER: disabled(2)

DIAL-CONTROL-MIB::dialCtlPeerCfgTrapEnable.2000.90 = INTEGER: disabled(2)

DIAL-CONTROL-MIB::dialCtlPeerCfgStatus.1000.91 = INTEGER: active(1)

DIAL-CONTROL-MIB::dialCtlPeerCfgStatus.2000.90 = INTEGER: active(1)

DIAL-CONTROL-MIB::dialCtlPeerStatsConnectTime.1000.91 = Gauge32: 0 seconds

DIAL-CONTROL-MIB::dialCtlPeerStatsConnectTime.2000.90 = Gauge32: 0 seconds

DIAL-CONTROL-MIB::dialCtlPeerStatsChargedUnits.1000.91 = Gauge32: 0

DIAL-CONTROL-MIB::dialCtlPeerStatsChargedUnits.2000.90 = Gauge32: 0

DIAL-CONTROL-MIB::dialCtlPeerStatsSuccessCalls.1000.91 = Gauge32: 0

DIAL-CONTROL-MIB::dialCtlPeerStatsSuccessCalls.2000.90 = Gauge32: 0

DIAL-CONTROL-MIB::dialCtlPeerStatsFailCalls.1000.91 = Gauge32: 0

DIAL-CONTROL-MIB::dialCtlPeerStatsFailCalls.2000.90 = Gauge32: 0

DIAL-CONTROL-MIB::dialCtlPeerStatsAcceptCalls.1000.91 = Gauge32: 0

DIAL-CONTROL-MIB::dialCtlPeerStatsAcceptCalls.2000.90 = Gauge32: 0

DIAL-CONTROL-MIB::dialCtlPeerStatsRefuseCalls.1000.91 = Gauge32: 0

DIAL-CONTROL-MIB::dialCtlPeerStatsRefuseCalls.2000.90 = Gauge32: 0

DIAL-CONTROL-MIB::dialCtlPeerStatsLastDisconnectCause.1000.91 = ""

DIAL-CONTROL-MIB::dialCtlPeerStatsLastDisconnectCause.2000.90 = ""

DIAL-CONTROL-MIB::dialCtlPeerStatsLastDisconnectText.1000.91 = STRING:

DIAL-CONTROL-MIB::dialCtlPeerStatsLastDisconnectText.2000.90 = STRING:

DIAL-CONTROL-MIB::dialCtlPeerStatsLastSetupTime.1000.91 = Timeticks:

(1102966) 3:03:49.66

DIAL-CONTROL-MIB::dialCtlPeerStatsLastSetupTime.2000.90 = Timeticks:

(1102799) 3:03:47.99

DIAL-CONTROL-MIB::callActivePeerAddress.1102799.1 = STRING: 2000

DIAL-CONTROL-MIB::callActivePeerAddress.1102966.1 = STRING: 1000

DIAL-CONTROL-MIB::callActivePeerSubAddress.1102799.1 = STRING:

DIAL-CONTROL-MIB::callActivePeerSubAddress.1102966.1 = STRING:

DIAL-CONTROL-MIB::callActivePeerId.1102799.1 = INTEGER: 2000

DIAL-CONTROL-MIB::callActivePeerId.1102966.1 = INTEGER: 1000

DIAL-CONTROL-MIB::callActivePeerIfIndex.1102799.1 = INTEGER: 90

DIAL-CONTROL-MIB::callActivePeerIfIndex.1102966.1 = INTEGER: 91

DIAL-CONTROL-MIB::callActiveLogicalIfIndex.1102799.1 = INTEGER: 37

DIAL-CONTROL-MIB::callActiveLogicalIfIndex.1102966.1 = INTEGER: 0

DIAL-CONTROL-MIB::callActiveConnectTime.1102799.1 = Timeticks:

(1104123) 3:04:01.23

DIAL-CONTROL-MIB::callActiveConnectTime.1102966.1 = Timeticks:

(1104123) 3:04:01.23

DIAL-CONTROL-MIB::callActiveCallState.1102799.1 = INTEGER: active(4)

DIAL-CONTROL-MIB::callActiveCallState.1102966.1 = INTEGER: active(4)

DIAL-CONTROL-MIB::callActiveCallOrigin.1102799.1 = INTEGER: answer(2)

DIAL-CONTROL-MIB::callActiveCallOrigin.1102966.1 = INTEGER: originate(1)

DIAL-CONTROL-MIB::callActiveChargedUnits.1102799.1 = Gauge32: 0

DIAL-CONTROL-MIB::callActiveChargedUnits.1102966.1 = Gauge32: 0

DIAL-CONTROL-MIB::callActiveInfoType.1102799.1 = INTEGER: speech(2)

DIAL-CONTROL-MIB::callActiveInfoType.1102966.1 = INTEGER: speech(2)

DIAL-CONTROL-MIB::callActiveTransmitPackets.1102799.1 = Gauge32: 7875641

DIAL-CONTROL-MIB::callActiveTransmitPackets.1102966.1 = Gauge32: 7875388

DIAL-CONTROL-MIB::callActiveTransmitBytes.1102799.1 = Gauge32: 157512782

DIAL-CONTROL-MIB::callActiveTransmitBytes.1102966.1 = Gauge32: 157507741

DIAL-CONTROL-MIB::callActiveReceivePackets.1102799.1 = Gauge32: 7875955

DIAL-CONTROL-MIB::callActiveReceivePackets.1102966.1 = Gauge32: 7875641

DIAL-CONTROL-MIB::callActiveReceiveBytes.1102799.1 = Gauge32: 157519081

DIAL-CONTROL-MIB::callActiveReceiveBytes.1102966.1 = Gauge32: 157512782

DIAL-CONTROL-MIB::callHistoryTableMaxLength.0 = INTEGER: 50

DIAL-CONTROL-MIB::callHistoryRetainTimer.0 = INTEGER: 15 minutes

Informações Relacionadas

- Ferramentas MIB do Cisco IOS

- Cisco SNMP Object Navigator

- Notas técnicas de SNMP

- Suporte Técnico e Documentação - Cisco Systems