BRI back-up van ISDN met back-up-interface

Downloadopties

  • PDF     (219.8 KB)
    Met Adobe Reader op diverse apparaten bekijken
  • ePub     (92.2 KB)
    Bekijken in diverse apps op iPhone, iPad, Android, Sony Reader of Windows Phone
  • Mobi (Kindle)     (109.9 KB)
    Op Kindle-apparaat of via Kindle-app op meerdere apparaten bekijken
Bijgewerkt:4 februari 2010
Document-id:11047

Inclusief taalgebruik

De documentatie van dit product is waar mogelijk geschreven met inclusief taalgebruik. Inclusief taalgebruik wordt in deze documentatie gedefinieerd als taal die geen discriminatie op basis van leeftijd, handicap, gender, etniciteit, seksuele oriëntatie, sociaaleconomische status of combinaties hiervan weerspiegelt. In deze documentatie kunnen uitzonderingen voorkomen vanwege bewoordingen die in de gebruikersinterfaces van de productsoftware zijn gecodeerd, die op het taalgebruik in de RFP-documentatie zijn gebaseerd of die worden gebruikt in een product van een externe partij waarnaar wordt verwezen. Lees meer over hoe Cisco gebruikmaakt van inclusief taalgebruik.

Over deze vertaling

Cisco heeft dit document vertaald via een combinatie van machine- en menselijke technologie om onze gebruikers wereldwijd ondersteuningscontent te bieden in hun eigen taal. Houd er rekening mee dat zelfs de beste machinevertaling niet net zo nauwkeurig is als die van een professionele vertaler. Cisco Systems, Inc. is niet aansprakelijk voor de nauwkeurigheid van deze vertalingen en raadt aan altijd het oorspronkelijke Engelstalige document (link) te raadplegen.

Inleiding

Dit document biedt een voorbeeldconfiguratie voor de back-up van ISDN en biedt basisinformatie over het oplossen van problemen voor dit type configuratie.

Raadpleeg voor informatie over de meest gebruikelijke implementaties van ISDN-back-up en vergelijkingen tussen deze onderdelen het volgende document: Evalueren van back-upinterfaces, zwevende statische routen en Dialer Watch voor DDR-back-up.

Voorwaarden

Vereisten

Er zijn geen specifieke voorwaarden van toepassing op dit document.

Gebruikte componenten

De informatie in dit document is gebaseerd op de onderstaande software- en hardwareversies.

  • Twee Cisco 2500 routers (Frame Relay data-eindapparatuur [DTEs]) die Cisco IOS®-softwarereleases 12.2(3) en 12.2(5) uitvoeren.

  • Eén Cisco 4500-router die fungeert als een Frame Relay-switch.

De informatie in dit document is gebaseerd op apparaten in een specifieke laboratoriumomgeving. Alle apparaten die in dit document worden beschreven, hadden een opgeschoonde (standaard)configuratie. Als u in een levend netwerk werkt, zorg er dan voor dat u de potentiële impact van om het even welke opdracht begrijpt alvorens het te gebruiken.

Conventies

Zie de Cisco Technical Tips Convention voor meer informatie over documentconventies.

Configureren

Deze sectie bevat informatie over het configureren van de functies die in dit document worden beschreven.

N.B.: Als u aanvullende informatie wilt vinden over de opdrachten in dit document, gebruikt u het Opdrachtplanningprogramma (alleen geregistreerd klanten).

Netwerkdiagram

Dit document gebruikt de netwerkinstellingen die in het onderstaande schema zijn weergegeven.

bri_isdn_11047.gif

Configuraties

Dit document maakt gebruik van de onderstaande configuraties.

krimson (Cisco 2500 router) 
krimson#show running-config
Building configuration...

!
version 12.2
service timestamps debug datetime msec
service timestamps log datetime msec
         
!
hostname krimson
!
!
username kevin password 0 <password> !
isdn switch-type basic-net3
!
!
interface Loopback0
ip address 10.7.7.1 255.255.255.0
ip ospf network point-to-point
!
interface Ethernet0
ip address 10.200.16.30 255.255.255.0
!
interface Serial1
bandwidth 64
no ip address
encapsulation frame-relay
no ip route-cache
no ip mroute-cache
!
interface Serial1.1 point-to-point
backup interface Dialer0
ip address 10.5.5.2 255.255.255.0
no ip route-cache
frame-relay interface-dlci 20 
!
interface BRI0
description Testanschluss ISDN(intern), Nr. 4420038
no ip address
encapsulation ppp
no ip route-cache
no ip mroute-cache
load-interval 30
no keepalive
dialer pool-member 1
isdn switch-type basic-net3
no fair-queue
no cdp enable
ppp authentication chap
!
interface Dialer0
ip address 10.9.9.1 255.255.255.0
encapsulation ppp
no ip route-cache
no ip mroute-cache
dialer pool 1
dialer remote-name kevin
dialer string 6120
dialer-group 1
no cdp enable
ppp authentication chap
!
router ospf 10
log-adjacency-changes
network 10.5.5.0 0.0.0.255 area 0
network 10.7.7.0 0.0.0.255 area 0
network 10.9.9.0 0.0.0.255 area 0
!
ip default-gateway 10.200.16.1
no ip classless
no ip http server
!
access-list 105 permit ip any host 10.7.7.1
access-list 105 permit ip any host 10.8.8.1
access-list 105 permit ip any any
dialer-list 1 protocol ip permit
!
line con 0
exec-timeout 0 0
privilege level 15
line aux 0
transport input all
line vty 0 4
exec-timeout 0 0
password <password> login
!
end

Kevin (Cisco 2500 router) 
kevin#show running-config
Building configuration...

version 12.2
service timestamps debug datetime msec
service timestamps log datetime msec
!
hostname kevin
!
!
username krimson password 0 <password> !
isdn switch-type basic-net3
!
!
interface Loopback0
ip address 10.8.8.1 255.255.255.0
ip ospf network point-to-point
!
interface Loopback1
ip address 172.19.0.1 255.255.255.255
!
interface Ethernet0
ip address 10.200.16.26 255.255.255.0
!
interface Serial0
no ip address
encapsulation frame-relay
!
interface Serial0.1 point-to-point
ip address 10.5.5.1 255.255.255.0
no cdp enable
frame-relay interface-dlci 20 
!
interface BRI0
no ip address
encapsulation ppp
dialer pool-member 1
isdn switch-type basic-net3
no cdp enable
ppp authentication chap
!
interface Dialer0
ip address 10.9.9.2 255.255.255.0
encapsulation ppp
dialer pool 1
dialer remote-name krimson
dialer-group 1
no cdp enable
ppp authentication chap
!
router ospf 10
log-adjacency-changes
network 10.5.5.0 0.0.0.255 area 0
network 10.8.8.0 0.0.0.255 area 0
network 10.9.9.0 0.0.0.255 area 0
!
ip default-gateway 10.200.16.1
ip classless
!
dialer-list 1 protocol ip permit
no cdp run
!        
line con 0        
exec-timeout 0 0
line aux 0
modem InOut
line vty 0 4
exec-timeout 0 0
password <password> login
!
ntp clock-period 17180102
ntp server 10.200.20.134
end

Verifiëren

Deze sectie verschaft informatie die u kunt gebruiken om te bevestigen dat uw configuratie correct werkt.

Gebruik de volgende opdrachten om de configuratie te controleren:

Bepaalde opdrachten worden ondersteund door het gereedschap Tolk-uitgang, waarmee u een analyse van de opdrachtoutput kunt bekijken.

  • tonen interfaces seriële - Hiermee geeft u informatie weer over de multicast data-link Connection identifier (DLCI), de DLCI’s die op de interface worden gebruikt en de DLCI’s die voor de Local Management Interface (LMI) worden gebruikt.

  • interfacetaler tonen - Hiermee geeft u informatie over de dialerinterface weer.

  • Toon ip route- Hiermee geeft u IP-routingangen weer. 

   krimson#show interface serial 1.1 

 ! --- The initial state before the simulated Frame Relay network failure. ! --- The primary link is up and functional. 

   
   Serial1.1 is up, line protocol is up 
   Hardware is HD64570
   Internet address is 10.5.5.2/24
   Backup interface Dialer0, failure delay 0 sec, 
   secondary disable delay 0 sec
   MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec, 
   reliability 255/255, txload 1/255, rxload 1/255
   Encapsulation FRAME-RELAY
   
   krimson#show int dialer 0 

 ! --- Initial state. The backup interface is in standby mode and inactive.

   Dialer0 is standby mode (spoofing), line protocol is down (spoofing)
   Hardware is Unknown
   Internet address is 10.9.9.1/24
   MTU 1500 bytes, BW 56 Kbit, DLY 20000 usec, 
   reliability 255/255, txload 1/255, rxload 1/255
   Encapsulation PPP, loopback not set
   DTR is pulsed for 1 seconds on reset
   Last input 1w6d, output never, output hang never
   Last clearing of "show interface" counters 6w4d
   Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
   Queueing strategy: weighted fair
   Output queue: 0/1000/64/0 (size/max total/threshold/drops) 
   Conversations 0/1/16 (active/max active/max total)
   Reserved Conversations 0/0 (allocated/max allocated)
   Available Bandwidth 42 kilobits/sec
   5 minute input rate 0 bits/sec, 0 packets/sec
   5 minute output rate 0 bits/sec, 0 packets/sec
   596 packets input, 48924 bytes
   600 packets output, 49280 bytes
   
   krimson#show ip route
   Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
   D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
   N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
   E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
   i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
   * - candidate default, U - per-user static route, o - ODR
   P - periodic downloaded static route
   
   Gateway of last resort is 10.200.16.1 to network 0.0.0.0
   
   192.168.64.0/30 is subnetted, 1 subnets
   C 192.168.64.0 is directly connected, Dialer4
   10.0.0.0/24 is subnetted, 6 subnets
   O 10.9.9.0 [110/3347] via 10.5.5.1, 00:03:34, Serial1.1
   O 10.8.8.0 [110/1563] via 10.5.5.1, 00:03:34, Serial1.1 

 ! --- The route to the tested destination network points to the ! --- still-active primary link.

   
   C 10.5.5.0 is directly connected, Serial1.1
   C 10.7.7.0 is directly connected, Loopback0
   C 10.9.8.0 is directly connected, Dialer1
   C 10.200.16.0 is directly connected, Ethernet0
   S* 0.0.0.0/0 [1/0] via 10.200.16.1

Hier kunnen we zien dat de Frame Relay-interface naar beneden gaat.

   krimson#
   *Apr 16 23:56:47.840: %LINK-3-UPDOWN: Interface Serial1, 
   changed state to down
   *Apr 16 23:56:47.848: OSPF: Interface Serial1.1 going Down 

 ! --- Here we have simulated a failure within the Frame Relay network. ! --- We can see what was conducted to the Frame Relay DTE router, ! --- and the subinterface going down.

   *Apr 16 23:56:47.852: %OSPF-5-ADJCHG: Process 10, 
   Nbr 172.19.0.1 on Serial1.1    
   from FULL to DOWN, Neighbor Down: Interface down or detached
   *Apr 16 23:56:48.736: BACKUP(Serial1.1): event = primary went down
   *Apr 16 23:56:48.740: BACKUP(Serial1.1): changed state to 
   "waiting to backup"
   *Apr 16 23:56:48.744: BACKUP(Serial1.1): event = timer expired
   *Apr 16 23:56:48.748: Di0 DDR is shutdown, could not clear interface.
   *Apr 16 23:56:48.752: BACKUP(Serial1.1): 
   secondary interface (Dialer0) made active 

 ! --- The configured backup interface is active.

   *Apr 16 23:56:48.752: BACKUP(Serial1.1): changed state to "backup mode"
   *Apr 16 23:56:48.756: OSPF: Interface Dialer0 going Up
   *Apr 16 23:56:48.760: BR0 DDR: rotor dialout [priority]
   *Apr 16 23:56:48.764: BR0 DDR: Dialing cause ip (s=10.9.9.1, d=224.0.0.5) 

 ! --- OSPF packets trigger the call.

   *Apr 16 23:56:48.768: BR0 DDR: Attempting to dial 6120
   *Apr 16 23:56:48.784: ISDN BR0: TX -> SETUP pd = 8 callref = 0x3E
   *Apr 16 23:56:48.792: Bearer Capability i = 0x8890
   *Apr 16 23:56:48.796: Channel ID i = 0x83
   *Apr 16 23:56:48.804: Called Party Number i = 0x80, '6120', 
   Plan:Unknown, Type:Unknown
   *Apr 16 23:56:48.844: %LINEPROTO-5-UPDOWN: Line protocol on  
   Interface Serial1, changed state to down
   *Apr 16 23:56:48.884: ISDN BR0: RX <- CALL_PROC pd = 8 callref = 0xBE
   *Apr 16 23:56:48.892: Channel ID i = 0x89
   *Apr 16 23:56:49.144: ISDN BR0: RX <- CONNECT pd = 8 callref = 0xBE
   *Apr 16 23:56:49.160: %LINK-3-UPDOWN: Interface BRI0:1, 
   changed state to up
   *Apr 16 23:56:49.168: %DIALER-6-BIND: 
   Interface BR0:1 bound to profile Di0
   *Apr 16 23:56:49.176: BR0:1 PPP: Treating connection as a callout
   *Apr 16 23:56:49.180: BR0:1 PPP: Phase is ESTABLISHING, Active Open 
   [0 sess, 0 load]
   *Apr 16 23:56:49.184: BR0:1 LCP: O CONFREQ [Closed] id 49 len 15
   *Apr 16 23:56:49.188: BR0:1 LCP: AuthProto CHAP (0x0305C22305)
   *Apr 16 23:56:49.188: BR0:1 LCP: MagicNumber 0xF2143EDB (0x0506F2143EDB)
   *Apr 16 23:56:49.196: ISDN BR0: TX -> CONNECT_ACK pd = 8 callref = 0x3E
   *Apr 16 23:56:49.224: BR0:1 LCP: I CONFREQ [REQsent] id 83 len 15
   *Apr 16 23:56:49.228: BR0:1 LCP: AuthProto CHAP (0x0305C22305)
   *Apr 16 23:56:49.232: BR0:1 LCP: MagicNumber 0x9ADACD69 (0x05069ADACD69)
   *Apr 16 23:56:49.236: BR0:1 LCP: O CONFACK [REQsent] id 83 len 15
   *Apr 16 23:56:49.236: BR0:1 LCP: AuthProto CHAP (0x0305C22305)
   *Apr 16 23:56:49.240: BR0:1 LCP: MagicNumber 0x9ADACD69 (0x05069ADACD69)
   *Apr 16 23:56:49.244: BR0:1 LCP: I CONFACK [ACKsent] id 49 len 15
   *Apr 16 23:56:49.248: BR0:1 LCP: AuthProto CHAP (0x0305C22305)
   *Apr 16 23:56:49.252: BR0:1 LCP: MagicNumber 0xF2143EDB (0x0506F2143EDB)
   *Apr 16 23:56:49.252: BR0:1 LCP: State is Open
   *Apr 16 23:56:49.256: BR0:1 PPP: Phase is AUTHENTICATING, by both 
   [0 sess, 0 load]
   *Apr 16 23:56:49.260: BR0:1 CHAP: O CHALLENGE id 49 len 28 from "krimson"
   *Apr 16 23:56:49.276: BR0:1 CHAP: I CHALLENGE id 51 len 26 from "kevin"
   *Apr 16 23:56:49.284: BR0:1 CHAP: O RESPONSE id 51 len 28 from "krimson"
   *Apr 16 23:56:49.332: BR0:1 CHAP: I SUCCESS id 51 len 4
   *Apr 16 23:56:49.344: BR0:1 CHAP: I RESPONSE id 49 len 26 from "kevin"
   *Apr 16 23:56:49.352: BR0:1 CHAP: O SUCCESS id 49 len 4
   *Apr 16 23:56:49.356: BR0:1 PPP: Phase is UP [0 sess, 0 load]
   *Apr 16 23:56:49.360: BR0:1 IPCP: O CONFREQ [Not negotiated] id 41 len 10
   *Apr 16 23:56:49.364: BR0:1 IPCP: Address 10.9.9.1 (0x03060A090901)
   *Apr 16 23:56:49.376: BR0:1 IPCP: I CONFREQ [REQsent] id 29 len 10
   *Apr 16 23:56:49.380: BR0:1 IPCP: Address 10.9.9.2 (0x03060A090902)
   *Apr 16 23:56:49.384: BR0:1 IPCP: O CONFACK [REQsent] id 29 len 10
   *Apr 16 23:56:49.388: BR0:1 IPCP: Address 10.9.9.2 (0x03060A090902)
   *Apr 16 23:56:49.396: BR0:1 IPCP: I CONFACK [ACKsent] id 41 len 10
   *Apr 16 23:56:49.400: BR0:1 IPCP: Address 10.9.9.1 (0x03060A090901)
   *Apr 16 23:56:49.400: BR0:1 IPCP: State is Open
   *Apr 16 23:56:49.408: BR0:1 DDR: dialer protocol up
   *Apr 16 23:56:49.416: Di0 IPCP: Install route to 10.9.9.2
   *Apr 16 23:56:49.960: OSPF: Rcv hello from 172.19.0.1 area 0 from 
   Dialer0 10.9.9.2
   *Apr 16 23:56:49.964: OSPF: End of hello processing
   *Apr 16 23:56:50.356: %LINEPROTO-5-UPDOWN: 
   Line protocol on Interface BRI0:1, changed state to up
   *Apr 16 23:56:50.748: %LINK-3-UPDOWN: Interface Dialer0, 
   changed state to up
   *Apr 16 23:56:50.752: Di0 LCP: Not allowed on a Dialer Profile
   *Apr 16 23:56:50.752: BACKUP(Dialer0): event = primary came up
   *Apr 16 23:56:55.176: %ISDN-6-CONNECT: 
   Interface BRI0:1 is now connected to 6120 kevin
   *Apr 16 23:56:58.804: OSPF: Rcv DBD from 172.19.0.1 on Dialer0 
   seq 0x988 opt 0x42 flag 0x7 len 32 mtu 1500 state INIT
   *Apr 16 23:56:58.808: OSPF: 2 Way Communication to 172.19.0.1 
   on Dialer0, state 2WAY
   
   krimson#show interface serial 1.1
   Serial1.1 is down, line protocol is down 
   
! --- The primary link is down.

   Hardware is HD64570
   Internet address is 10.5.5.2/24
   Backup interface Dialer0, failure delay 0 sec, 
   secondary disable delay 0 sec
   MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec, 
   reliability 255/255, txload 1/255, rxload 1/255
   Encapsulation FRAME-RELAY
   
   krimson#show interface dialer 0
   Dialer0 is up, line protocol is up (spoofing) 

 ! --- The backup interface is active and bearing traffic.

   Hardware is Unknown
   Internet address is 10.9.9.1/24
   MTU 1500 bytes, BW 56 Kbit, DLY 20000 usec, 
   reliability 255/255, txload 1/255, rxload 1/255
   Encapsulation PPP, loopback not set
   DTR is pulsed for 1 seconds on reset
   Interface is bound to BR0:1
   Last input 1w6d, output never, output hang never
   Last clearing of "show interface" counters 6w4d
   Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
   Queueing strategy: weighted fair
   Output queue: 0/1000/64/0 (size/max total/threshold/drops) 
   Conversations 0/1/16 (active/max active/max total)
   Reserved Conversations 0/0 (allocated/max allocated)
   Available Bandwidth 42 kilobits/sec
   5 minute input rate 0 bits/sec, 0 packets/sec
   5 minute output rate 0 bits/sec, 0 packets/sec
   614 packets input, 50240 bytes
   618 packets output, 50584 bytes
   Bound to:
   BRI0:1 is up, line protocol is up 
   Hardware is BRI
   MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec, 
   reliability 255/255, txload 1/255, rxload 1/255
   Encapsulation PPP, loopback not set
   Keepalive not set
   DTR is pulsed for 1 seconds on reset
   Time to interface disconnect: idle 00:01:57
   Interface is bound to Di0 (Encapsulation PPP)
   LCP Open
   Open: IPCP
   Last input 00:00:01, output 00:00:02, output hang never
   Last clearing of "show interface" counters never
   Queueing strategy: fifo
   Output queue 0/40, 0 drops; input queue 0/75, 0 drops
   30 second input rate 0 bits/sec, 0 packets/sec
   30 second output rate 0 bits/sec, 0 packets/sec
   3910 packets input, 394443 bytes, 0 no buffer
   Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
   29 input errors, 18 CRC, 0 frame, 0 overrun, 0 ignored, 11 abort
   3613 packets output, 222417 bytes, 0 underruns
   0 output errors, 0 collisions, 27 interface resets
   0 output buffer failures, 0 output buffers swapped out
   607 carrier transitions
   
   krimson#show ip route
   Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
   D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
   N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
   E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
   i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
   * - candidate default, U - per-user static route, o - ODR
   P - periodic downloaded static route

Gateway of last resort is 10.200.16.1 to network 0.0.0.0
 
192.168.64.0/30 is subnetted, 1 subnets
   C 192.168.64.0 is directly connected, Dialer4
   10.0.0.0/8 is variably subnetted, 6 subnets, 2 masks
   C 10.9.9.2/32 is directly connected, Dialer0
   O 10.8.8.0/24 [110/1786] via 10.9.9.2, 00:00:53, Dialer0 
   
! --- The route entry to the destination network is now pointing to ! --- the backup interface as a next hop.

   C 10.9.9.0/24 is directly connected, Dialer0
   C 10.7.7.0/24 is directly connected, Loopback0
   C 10.9.8.0/24 is directly connected, Dialer1
   C 10.200.16.0/24 is directly connected, Ethernet0
   S* 0.0.0.0/0 [1/0] via 10.200.16.1
   
   krimson#ping 10.8.8.1
   Type escape sequence to abort.
   Sending 5, 100-byte ICMP Echos to 10.8.8.1, timeout is 2 seconds:
   !!!!!
   Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/40 ms

Hier kunnen we zien dat het systeem terugkeert naar de oorspronkelijke status nadat de fout in het Frame Relay-netwerk is gewist:

krimson#show interface serial 1.1
   Serial1.1 is up, line protocol is up 
   Hardware is HD64570
   Internet address is 10.5.5.2/24
   Backup interface Dialer0, failure delay 0 sec, 
   secondary disable delay 0 sec
   MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec, 
   reliability 255/255, txload 1/255, rxload 1/255
   Encapsulation FRAME-RELAY
   
   krimson#show interface dialer 0
   Dialer0 is standby mode (spoofing), line protocol is down (spoofing)
   Hardware is Unknown
   Internet address is 10.9.9.1/24
   MTU 1500 bytes, BW 56 Kbit, DLY 20000 usec, 
   reliability 255/255, txload 1/255, rxload 1/255
   Encapsulation PPP, loopback not set
   DTR is pulsed for 1 seconds on reset
   Last input 1w6d, output never, output hang never
   Last clearing of "show interface" counters 6w5d
   Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
   Queueing strategy: weighted fair
   Output queue: 0/1000/64/0 (size/max total/threshold/drops) 
   Conversations 0/1/16 (active/max active/max total)
   Reserved Conversations 0/0 (allocated/max allocated)
   Available Bandwidth 42 kilobits/sec
   5 minute input rate 0 bits/sec, 0 packets/sec
   5 minute output rate 0 bits/sec, 0 packets/sec
   665 packets input, 54008 bytes
   671 packets output, 54548 bytes
   
   krimson#show ip route
   Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
   D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
   N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
   E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
   i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
   * - candidate default, U - per-user static route, o - ODR
   P - periodic downloaded static route
   Gateway of last resort is 10.200.16.1 to network 0.0.0.0
   192.168.64.0/30 is subnetted, 1 subnets
   C 192.168.64.0 is directly connected, Dialer4
   10.0.0.0/24 is subnetted, 6 subnets
   O 10.9.9.0 [110/3347] via 10.5.5.1, 00:08:39, Serial1.1
   O 10.8.8.0 [110/1563] via 10.5.5.1, 00:08:39, Serial1.1
   C 10.5.5.0 is directly connected, Serial1.1
   C 10.7.7.0 is directly connected, Loopback0
   C 10.9.8.0 is directly connected, Dialer1
   C 10.200.16.0 is directly connected, Ethernet0
   S* 0.0.0.0/0 [1/0] via 10.200.16.1
   krimson#

Opmerking: Er is geen specifieke configuratie nodig op de aangeroepen zijde.

De zelfde show output die tijdens normaal gebruik wordt geregistreerd bevat de volgende informatie:

kevin#show interface serial 0.1
   Serial0.1 is up, line protocol is up 

 ! --- The primary interface is up and running.

   Hardware is HD64570
   Internet address is 10.5.5.1/24
   MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, 
   reliability 255/255, txload 1/255, rxload 1/255
   Encapsulation FRAME-RELAY
   
   kevin#show interface dialer 0
   Dialer0 is up (spoofing), line protocol is up (spoofing) 

 ! --- Note: On the called side, the dialer interface is active ! --- and not in standby mode.

   Hardware is Unknown
   Internet address is 10.9.9.2/24
   MTU 1500 bytes, BW 56 Kbit, DLY 20000 usec, 
   reliability 255/255, txload 1/255, rxload 1/255
   Encapsulation PPP, loopback not set
   DTR is pulsed for 1 seconds on reset
   Last input 1w6d, output never, output hang never
   Last clearing of "show interface" counters 4w2d
   Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
   Queueing strategy: weighted fair
   Output queue: 0/1000/64/0 (size/max total/threshold/drops) 
   Conversations 0/1/16 (active/max active/max total)
   Reserved Conversations 0/0 (allocated/max allocated)
   Available Bandwidth 42 kilobits/sec
   5 minute input rate 0 bits/sec, 0 packets/sec
   5 minute output rate 0 bits/sec, 0 packets/sec
   598 packets input, 49252 bytes
   596 packets output, 48924 bytes

   kevin#show ip route
   Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
   D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
   N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
   E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
   i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
   * - candidate default, U - per-user static route, o - ODR
   P - periodic downloaded static route
   
   Gateway of last resort is 10.200.16.1 to network 0.0.0.0
   
   172.17.0.0/32 is subnetted, 1 subnets
   S 172.17.247.195 [1/0] via 10.200.16.1
   172.19.0.0/32 is subnetted, 1 subnets
   C 172.19.0.1 is directly connected, Loopback1
   10.0.0.0/24 is subnetted, 5 subnets
   C 10.5.5.0 is directly connected, Serial0.1
   O 10.7.7.0 [110/65] via 10.5.5.2, 00:04:27, Serial0.1
   C 10.9.9.0 is directly connected, Dialer0
   C 10.8.8.0 is directly connected, Loopback0
   C 10.200.16.0 is directly connected, Ethernet0
   S* 0.0.0.0/0 [1/0] via 10.200.16.1

Hier vindt u dezelfde informatie die tijdens de fout is geregistreerd: 

kevin#show interface serial 0.1
   Serial0.1 is down, line protocol is down 
   Hardware is HD64570
   Internet address is 10.5.5.1/24
   MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, 
   reliability 255/255, txload 1/255, rxload 1/255
   Encapsulation FRAME-RELAY
   
   kevin#show interface dialer 0
   Dialer0 is up, line protocol is up (spoofing)
   Hardware is Unknown
   Internet address is 10.9.9.2/24
   MTU 1500 bytes, BW 56 Kbit, DLY 20000 usec, 
   reliability 255/255, txload 1/255, rxload 1/255
   Encapsulation PPP, loopback not set
   DTR is pulsed for 1 seconds on reset
   Interface is bound to BR0:1
   Last input 1w6d, output never, output hang never
   Last clearing of "show interface" counters 4w2d
   Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
   Queueing strategy: weighted fair
   Output queue: 0/1000/64/0 (size/max total/threshold/drops) 
   Conversations 0/1/16 (active/max active/max total)
   Reserved Conversations 0/0 (allocated/max allocated)
   Available Bandwidth 42 kilobits/sec
   5 minute input rate 0 bits/sec, 0 packets/sec
   5 minute output rate 0 bits/sec, 0 packets/sec
   618 packets input, 50700 bytes
   616 packets output, 50384 bytes
   Bound to:
   BRI0:1 is up, line protocol is up 
   Hardware is BRI
   MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec, 
   reliability 255/255, txload 1/255, rxload 1/255
   Encapsulation PPP, loopback not set
   Keepalive set (10 sec)
   DTR is pulsed for 1 seconds on reset
   Time to interface disconnect: idle 00:01:57
   Interface is bound to Di0 (Encapsulation PPP)
   LCP Open
   Open: IPCP
   Last input 00:00:03, output 00:00:02, output hang never
   Last clearing of "show interface" counters never
   Queueing strategy: fifo
   Output queue 0/40, 0 drops; input queue 0/75, 0 drops
   5 minute input rate 0 bits/sec, 0 packets/sec
   5 minute output rate 0 bits/sec, 0 packets/sec
   1280 packets input, 138077 bytes, 0 no buffer
   Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
   9789 input errors, 9789 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
   1309 packets output, 138487 bytes, 0 underruns
   0 output errors, 0 collisions, 15 interface resets
   0 output buffer failures, 0 output buffers swapped out
   351 carrier transitions
   
   kevin#show ip route
   Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
   D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
   N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
   E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
   i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
   * - candidate default, U - per-user static route, o - ODR
   P - periodic downloaded static route
   Gateway of last resort is 10.200.16.1 to network 0.0.0.0
   172.17.0.0/32 is subnetted, 1 subnets
   S 172.17.247.195 [1/0] via 10.200.16.1
   172.19.0.0/32 is subnetted, 1 subnets
   C 172.19.0.1 is directly connected, Loopback1
   10.0.0.0/8 is variably subnetted, 5 subnets, 2 masks
   O 10.7.7.0/24 [110/1786] via 10.9.9.1, 00:01:21, Dialer0
   C 10.9.9.0/24 is directly connected, Dialer0
   C 10.8.8.0/24 is directly connected, Loopback0
   C 10.9.9.1/32 is directly connected, Dialer0
   C 10.200.16.0/24 is directly connected, Ethernet0
   S* 0.0.0.0/0 [1/0] via 10.200.16.1

Problemen oplossen

Deze sectie bevat informatie waarmee u problemen met de configuratie kunt oplossen.

De configuraties van Frame Relay met point-to-point subinterfaces en Open Snelste pad (OSPF) als een routeringsprotocol dat hier wordt gebruikt, zijn specifiek voor deze installatie. De stappen voor het oplossen van problemen die worden getoond zijn echter algemener en kunnen worden gebruikt met verschillende configuraties zoals Frame Relay point-to-multipoint of een primaire verbinding met HDLC (High-Level Data Link Control) of Point to Point Protocol (PPP)-insluiting, ongeacht het routeringsprotocol dat wordt gebruikt.

Om de reservefunctionaliteit te verifiëren, is een van de interfaces op de Cisco 4500 router die als een switch van Frame Relay dienst doet in shutdown staat geplaatst om probleem binnen het netwerk van Frame Relay te simuleren. Dientengevolge, leidt dit tot de inactieve staat van PVC aan de router DTE via het netwerk van Frame Relay, en een subinterface van Frame Relay. Hiermee wordt de back-upinterface geactiveerd.

Opdrachten voor troubleshooting

Opmerking: Voordat u debug-opdrachten afgeeft, raadpleegt u Belangrijke informatie over debug-opdrachten.

  • debug van ISDN Q931

  • debug back-up gebeurtenissen: Debugs back-up gebeurtenissen.

  • debug dialer - Hiermee geeft u informatie over de pakketten of gebeurtenissen op een dialerinterface weer.

  • debug ppp onderhandeling - veroorzaakt het debug ppp bevel om PPP pakketten die tijdens PPP opstarten worden verzonden te tonen, waar PPP opties worden besproken.

  • debug van PPP-verificatie - veroorzaakt de debug ppp-opdracht om verificatieprotocolberichten weer te geven, inclusief Challenge Verificatie Protocol (CHAP)-pakketuitwisselingen en Wachtwoord Verificatieprotocol (PAP)-uitwisselingen.

  • ip ospf-gebeurtenissen debug - informatie over OSPF-gerelateerde gebeurtenissen, zoals nabijheid, overstroominformatie, aangewezen routerselectie en kortste pad voor eerste berekening (SPF)

  • debug frame-relais gebeurtenissen - schitterende informatie over Frame Relay ARP-antwoorden op netwerken die een multicast kanaal ondersteunen en dynamische adressering gebruiken.

Gerelateerde informatie

Revisiegeschiedenis

Revisie Publicatiedatum Opmerkingen
1.0
04-Feb-2010
Eerste vrijgave

Was dit document nuttig?

FeedbackFeedback

Contact Cisco

Dit document is van toepassing op deze producten