이 문서에서는 Cisco IOS® 플랫폼에서 다이얼 피어의 작동 상태를 이해하는 방법에 대해 설명합니다.
이 문서의 독자는 다음 주제에 대해 알고 있어야 합니다.
Voice-Network(VoIP, VoFR, VoATM) 및 POTS 다이얼 피어가 유효하지 않고 "작동 상태"인 경우, Cisco IOS 라우터/게이트웨이 인바운드 및 아웃바운드 다이얼 피어 매칭 프로세스에 대해 고려되지 않습니다.유효/작동 상태로 간주하려면 다이얼 피어가 다음 조건 중 하나를 충족해야 합니다.
Destination-pattern과 음성 포트 또는 세션 대상이 구성됩니다.
수신 called-number가 구성되었습니다.
응답 주소가 구성되었습니다.
이 문서는 특정 소프트웨어 및 하드웨어 버전으로 한정되지 않습니다.
문서 규칙에 대한 자세한 내용은 Cisco 기술 팁 표기 규칙을 참조하십시오.
이전 세 가지 규칙 기준에 따라 이 표에는 작동 중지 상태에 있는 다이얼 피어 구성의 예가 표시됩니다.
다이얼 피어 예 |
---|
dial-peer voice 1 pots port 1/0:23 !--- Invalid dial-peer (rule 1): Has voice-port configured only. ! dial-peer voice 2 pots destination-pattern 1T !--- Invalid dial-peer (rule 1): Has destination-pattern configured only. ! dial-peer voice 6 voip session target ipv4:172.16.13.111 !--- Invalid dial-peer (rule 1): Has session target configured only. ! dial-peer voice 7 voip destination-pattern 83... !--- Invalid dial-peer (rule 1): Has destination-pattern configured only. ! |
참고: 하위 명령이 없는 다이얼 피어 컨피그레이션 문은 1, 2 및 3을 위반하면 유효하지 않은 것으로 간주됩니다.
이전 세 가지 규칙 기준에 따라 이 표에는 작동 상태에 있는 다이얼 피어 구성의 예가 표시됩니다.
유효한 피어 예 |
---|
dial-peer voice 3 pots destination-pattern 1T port 1/0:23 prefix 1 !--- Valid dial-peer (rule 1): Has voice-port and destination-pattern configured. ! dial-peer voice 4 pots incoming called-number 83. !--- Valid dial-peer (rule 2): Has incoming called-number configured. ! dial-peer voice 5 pots answer-address 408 !--- Valid dial-peer (rule 2): Has answer-address configured. ss configured. ! dial-peer voice 8 voip destination-pattern 83... session target ipv4:172.16.13.111 !--- Valid dial-peer (rule 1): Has session target and destination-pattern configured. ! dial-peer voice 9 voip incoming called-number . !--- Valid dial-peer (rule 2): Has incoming called-number configured. ! dial-peer voice 10 voip answer-address 6666 !--- Valid dial-peer (rule 2): Has answer-address configured. ! |
참고: 인바운드 매칭을 위한 다이얼 피어에 수신 called-number 또는 answer-address가 구성되고 destination-pattern 명령이 추가되었다고 가정합니다.명령 대상 패턴 문자열을 추가하면 다이얼 피어가 정상적으로 작동하지 않습니다.이는 라우터가 아웃바운드 다이얼 피어의 일치 목적을 위해 대상 패턴을 주소(세션 대상) 또는 음성 포트(포트)에 매핑하기 때문입니다.이 시나리오에서는 매핑할 내용이 없습니다.예를 들어 다이얼 피어 4, 5, 9 및 10에 대상 패턴을 추가하면 작동 상태가 다운으로 변경됩니다.
참고: 다이얼 피어 4 및 5에서 대상 패턴을 제거하고 port 명령을 추가하면 다이얼 피어는 계속 유효합니다.마찬가지로 destination-pattern을 제거하고 9와 10에서 session-target 명령을 추가하면 작동 상태로 유지됩니다.
다이얼 피어 컨피그레이션의 유효성을 확인하려면 Cisco IOS 명령 show dial-peer voice summary를 사용합니다.
다이얼 피어 구성 확인 |
---|
2600#show dial-peer voice summary dial-peer hunt 0 PASS TAG TYPE ADMIN OPER PREFIX DEST-PATTERN PREF THRU SESS-TARGET PORT 1 pots up down 0 1/0:23 2 pots up down 1T 0 3 pots up up 1 1T 0 1/0:23 4 pots up up 0 5 pots up up 0 6 voip up down 0 syst ipv4:172.16.13.111 7 voip up down 83... 0 syst 8 voip up up 83... 0 syst ipv4:172.16.13.111 9 voip up up 0 syst 10 voip up up 0 syst |