이 문서에서는 SIP 전화기를 사용하는 독립형 Cisco Unified Communications Manager Express(CME)를 설정하기 위한 단계별 지침을 제공합니다. Cisco Unified Communications Manager Express 시스템 및 SIP 폰을 설정하기 위한 컨피그레이션과 함께 4개의 SIP 전화가 장착된 Cisco Unified Communications Manager Express 시스템에 대한 개요를 제공합니다.
참고: 이 문서에서는 Cisco Unified Communications Manager Express가 Cisco Unity Express와 상호 운용될 수 있도록 하는 컨피그레이션 단계를 다루지만, Cisco Unity Express 컨피그레이션은 이 문서의 범위에 포함되지 않습니다. Cisco Unified Communications Manager Express 및 Cisco Unity Express 구성에 대한 자세한 내용은 Cisco CallManager Express/Cisco Unity Express 구성 예를 참조하십시오.
이 문서에 대한 특정 요건이 없습니다.
이 문서의 내용은 다음 하드웨어 버전을 기반으로 합니다.
Cisco Unified Communications Manager Express 4.2 및 Cisco IOS® Software 릴리스 12.4(11)XW2를 실행하는 Cisco 2801
9포트 더블 와이드 10/100BASE-T 이더넷 스위치 HWIC
Cisco 7970 SIP Phone
Cisco 3911 SIP 전화
이 문서의 정보는 다음 펌웨어 버전을 기반으로 합니다.
7970 SIP(IP Phone) - SIP70.8-2-1S
3911 SIP(IP Phone) - SIP3951.8-0-2-9
각 Cisco Unified Communications Manager Express 버전에 사용할 적절한 SIP 펌웨어를 결정하려면 Cisco Unified CME 및 Cisco IOS Software 버전 호환성 매트릭스를 참조하십시오. Cisco Unified Communications Manager Express 4.2를 사용하므로 Cisco Unified Communications Manager Express 4.2 사양 링크를 참조하십시오.
SIP phoneload는 다음 위치에서 다운로드할 수 있습니다.
소프트웨어 다운로드-Cisco IP Phone 펌웨어(등록된 고객만 해당) —7970 전화의 경우 SIP 전화 다운로드 cmterm-7970_7971-sip.8-2-1.zip 파일을 다운로드하고 파일의 압축을 TFTP 폴더에 풉니다.
소프트웨어 다운로드-Cisco Unified SIP Phone 3911/51 펌웨어(등록된 고객만 해당) —3911 전화의 경우 cmterm-3951-sip.8-0-2.zip 파일을 다운로드하고 TFTP 폴더에 압축을 풉니다.
참고: 3911 및 3951 전화기는 동일한 펌웨어를 사용하므로 파일 이름이 3951 전화기를 반영한다는 점에 유의할 필요가 없습니다.
TFTP 폴더에서 두 ZIP 파일의 압축을 모두 푼 후 모든 펌웨어 파일을 TFTP 서버와 함께 Cisco Unified Communications Manager Express 플래시에 복사합니다. 이 모든 파일을 플래시에 복사해야 합니다.
SIP3951.8-0-2-9.loads SIP3951.8-0-2-9.zz DSP3951.0-0-0-1.zz BOOT3951.0-0-0-9.zz SIP70.8-2-1S.loads term70.default.loads term71.default.loads apps70.8-0-2-55.sbn cnu70.8-2-0-55.sbn cvm70.sip.8-2-0-55.sbn dsp70.8-2-0-55.sbn jar70.sip.8-0-2-25.sbn
이 문서의 정보는 특정 랩 환경의 디바이스를 토대로 작성되었습니다. 이 문서에 사용된 모든 디바이스는 초기화된(기본) 컨피그레이션으로 시작되었습니다. 현재 네트워크가 작동 중인 경우, 모든 명령어의 잠재적인 영향을 미리 숙지하시기 바랍니다.
문서 규칙에 대한 자세한 내용은 Cisco 기술 팁 표기 규칙을 참조하십시오.
이 섹션에는 이 문서에서 설명하는 기능을 구성하기 위한 정보가 표시됩니다.
다음 표에는 이 설정에 사용되는 주소 지정 체계가 나와 있습니다.
목적 | VLAN | 네트워크 | 인터페이스 | 인터페이스 주소 |
---|---|---|---|---|
음성 | 192 | 192.168.10.0/24 | VLAN 192 | 192.168.10.1/24 |
데이터 | 100 | 10.10.10.0/24 | VLAN 100 | 10.10.10.1/24 |
프로토콜 | 전화 유형 | 내선 번호 | 전화 번호 외부 마스크 |
---|---|---|---|
SIP | 7970 | 101 | 4085251001 |
SIP | 7970 | 102 | 4085251002 |
SIP | 3911 | 103 | 4085251003 |
SIP | 3911 | 104 | 4085251004 |
음성 메일 파일럿 번호 | 100 | AA 파일럿 | 110 |
MWI 켜기 | 800 | MWI 끄기 | 801 |
참고: 이 섹션에서 사용되는 명령에 대한 자세한 내용을 보려면 를 사용하십시오.
이 문서에서는 이 네트워크 설정을 사용합니다.
이 문서에서는 다음 설정을 사용합니다.
두 개의 개별 DHCP 풀을 구성해야 합니다. IP Phone은 Voice DHCP 풀을 사용하고 PC는 Data DHCP 풀을 사용합니다. TFTP 서버의 IP 주소를 제공하려면 IP Phone에서 DHCP 옵션 150을 사용해야 합니다.
두 풀 중 하나에 고정 IP 주소가 있는 디바이스가 있는 경우 주소 충돌을 방지하기 위해 이러한 주소를 DHCP 풀에서 제외해야 합니다. show ip dhcp binding 명령을 사용하여 라우터에서 수신하는 IP Phone 및 PC의 주소를 확인할 수 있습니다.
DHCP 컨피그레이션 |
---|
ip dhcp excluded-address 10.10.10.1 10.10.10.10 ip dhcp excluded-address 192.168.10.1 192.168.10.10 ! ip dhcp pool data network 10.10.10.0 255.255.255.0 default-router 10.10.10.1 ! ip dhcp pool voice network 192.168.10.0 255.255.255.0 option 150 ip 192.168.10.1 default-router 192.168.10.1 |
이 섹션에서는 데이터 및 음성 VLAN 모두에 대해 VLAN 인터페이스를 구성하고 해당 VLAN에 스위치 포트를 지정합니다.
참고: VLAN을 구성하기 전에 다음 명령을 사용하여 VLAN 데이터베이스에 이전 VLAN을 추가해야 합니다.
FastEthernet 인터페이스 및 Switchport 컨피그레이션 |
---|
CME-SIP#vlan database % Warning: It is recommended to configure VLAN from config mode, as VLAN database mode is being deprecated. Please consult user documentation for configuring VTP/VLAN in config mode. CME-SIP(vlan)#vlan 100 VLAN 100 modified: CME-SIP(vlan)#vlan 192 VLAN 192 modified: CME-SIP(vlan)#exit APPLY completed. Exiting.... CME-SIP# |
음성 및 데이터 VLAN에 모두 연결되도록 스위치 포트를 구성합니다. IP Phone은 음성 VLAN에 자동으로 할당되고 PC는 스위치 포트에 직접 연결되거나 데이터 VLAN에 할당된 IP Phone의 스위치 포트에 연결됩니다.
DHCP 컨피그레이션 |
---|
interface FastEthernet0/3/0 description 7970 Phone switchport trunk native vlan 100 switchport mode trunk switchport voice vlan 192 spanning-tree portfast ! interface FastEthernet0/3/1 description 7970 Phone switchport trunk native vlan 100 switchport mode trunk switchport voice vlan 192 spanning-tree portfast ! interface FastEthernet0/3/2 description 3911 Phone switchport trunk native vlan 100 switchport mode trunk switchport voice vlan 192 spanning-tree portfast ! interface FastEthernet0/3/3 description 3911 Phone switchport trunk native vlan 100 switchport mode trunk switchport voice vlan 192 spanning-tree portfast ! ! interface Vlan100 description Data VLAN ip address 10.10.10.1 255.255.255.0 ! interface Vlan192 description Voice VLAN ip address 192.168.10.1 255.255.255.0 |
이 컨피그레이션을 사용하면 Cisco Unified Communications Manager Express에서 해당 펌웨어의 IP Phone을 지원할 수 있습니다.
참고: 이 구성은 필수입니다.
TFTP 컨피그레이션 |
---|
tftp-server flash:SIP3951.8-0-2-9.loads tftp-server flash:SIP3951.8-0-2-9.zz tftp-server flash:DSP3951.0-0-0-1.zz tftp-server flash:BOOT3951.0-0-0-9.zz tftp-server flash:SIP70.8-2-1S.loads tftp-server flash:term70.default.loads tftp-server flash:term71.default.loads tftp-server flash:apps70.8-0-2-55.sbn tftp-server flash:cnu70.8-2-0-55.sbn tftp-server flash:cvm70.sip.8-2-0-55.sbn tftp-server flash:dsp70.8-2-0-55.sbn tftp-server flash:jar70.sip.8-0-2-25.sbn |
SIP에서 SIP 엔드포인트로의 통화를 허용하고 SIP 등록자를 활성화하도록 시스템을 구성합니다.
참고: 이 구성은 필수입니다.
음성 서비스 매개변수 컨피그레이션 |
---|
voice service voip allow-connections sip to sip !--- Enable SIP to SIP calls. sip registrar server expires max 1200 min 300 !--- Enable Cisco IOS SIP registrar. |
이 섹션에서는 음성 등록 전역 매개변수를 구성합니다.
참고: SIP에 대한 음성 등록 전역 컨피그레이션은 SCCP 전화기에 대한 전화 통신 서비스 컨피그레이션 매개변수와 유사합니다.
참고: 이 구성은 필수입니다.
음성 등록 전역 매개변수 컨피그레이션 |
---|
voice register global mode cme !--- Set Cisco IOS SIP registrar to CME mode. source-address 192.168.10.1 port 5060 !--- Set the source address for phone registration. max-dn 20 !--- Set max extensions. max-pool 10 !--- Set max phones. load 7970 SIP7 SIP70.8-2-1S !--- Specify phone loads for each phone type. load 3911 SIP3951.8-0-2-9 !--- Specify phone loads for each phone type. authenticate register !--- Set authentication for phone registration. authenticate realm cisco.com tftp-path flash: !--- Specify path for tftp files. create profile !--- Create configuration files for all phones. dialplan-pattern 1 4085251... extension-length 3 !--- Configure dial-plan pattern for the system. |
다음은 SIP 프로토콜을 사용하여 IP Phone을 Cisco CME(Unified Communications Manager Express)에 등록하는 절차를 설명하는 Cisco Support Community의 비디오 링크입니다.
CUCME에서 SIP 프로토콜을 사용하여 79xx Series IP Phone 등록
Cisco Unity Express와 상호 운용되도록 필요한 다이얼 피어 및 MWI ephone-dns를 구성합니다. Cisco Unified Communications Manager Express가 Cisco Unity Express와 상호 운용되도록 하려면 SIP Cisco Unified Communications Manager Express를 B2BUA(back to back user agent)로 구성해야 합니다. 즉 모든 시그널링 및 RTP 스트림이 Cisco Unified Communications Manager Express를 거칩니다. Cisco Unity Express에 연결하려면 이 컨피그레이션이 필요합니다.
Cisco Unity Express 연결 컨피그레이션 |
---|
dial-peer voice 2 voip destination-pattern 1.0 !--- Specify destination-pattern to reach CUE VM and AA. session target ipv4:10.1.10.1 !--- Configure IP address to reach Cisco Unity Express. session protocol sipv2 dtmf-relay sip-notify !--- Configure DTMF method to communicate with Cisco Unity Express. b2bua !--- Enable B2BUA for Cisco Unified Communications Manager Express !--- for calls to Cisco Unity Express. codec g711ulaw no vad |
SIP 전화용 MWI를 활성화하려면 Cisco Unity Express MWI for outcall 지원을 구성합니다.
Cisco Unity Express MWI 컨피그레이션 |
---|
ephone-dn 11 number 800 mwi on ! ephone-dn 12 number 801 mwi off |
전화기의 내선 번호를 생성하려면 음성 레지스터 dn을 구성합니다. 이전 네트워크 토폴로지에서는 여기에 지정된 대로 생성해야 하는 네 가지 확장이 있습니다.
참고: 이 구성은 필수입니다.
확장 컨피그레이션 |
---|
voice register dn 1 name Phone1 !--- Set display name. label 4085251001 !--- Set display label. number 101 !--- Set extension number. call-forward b2bua noan 100 timeout 20 !--- Configure call forward noan to voicemail pilot. call-forward b2bua busy 100 timeout 20 !--- Configure call forward busy to voicemail pilot. allow watch !--- Allow this number to be watched (presence). ! voice register dn 2 name Phone2 label 4085251002 number 102 call-forward b2bua noan 100 timeout 20 !--- Configure call forward noan to voicemail pilot. call-forward b2bua busy 100 timeout 20 !--- Configure call forward busy to voicemail pilot. allow watch ! voice register dn 3 name Phone3 label 4085251003 number 103 call-forward b2bua noan 100 timeout 20 !--- Configure call forward noan to voicemail pilot. call-forward b2bua busy 100 timeout 20 !--- Configure call forward busy to voicemail pilot. allow watch ! voice register dn 4 name Phone4 label 4085251004 number 104 call-forward b2bua noan 100 timeout 20 !--- Configure call forward noan to voicemail pilot. call-forward b2bua busy 100 timeout 20 !--- Configure call forward busy to voicemail pilot. allow watch |
각 SIP 전화에 대해 음성 레지스터 풀 매개변수를 구성합니다.
참고: SIP 전화의 음성 레지스터 풀은 SCCP 전화의 전화기와 동일합니다.
참고: 이 구성은 필수입니다.
음성 레지스터 풀 매개변수 컨피그레이션 |
---|
voice register pool 3 id mac 001A.A11B.500E !--- Specify phone mac-address. type 3911 !--- Specify phone type. number 1 dn 3 !--- Assign button 1 dn tag 3. dtmf-relay sip-notify !--- Configure dtmf-relay sip-notify to work !--- with Cisco Unity Express. codec g711ulaw !--- Specify codec. username user1 password cisco !--- Configure username and password for SIP registrar. |
참고: 음성 등록 풀에서 여러 DTMF 방법을 구성할 수 있지만 Cisco Unity Express에 음성 메일 상자가 있는 각 SIP 전화에 대해 dtmf-relay sip-notify를 구성합니다.
이 섹션에서는 BLF(Busy Lamp Field) 상태의 프레즌스와 같은 SIP 전화에 대한 고급 매개변수를 구성합니다. BLF가 포함된 프레즌스를 사용하면 SCCP 전화기 또는 SIP 전화기에서 다른 SIP 내선 번호의 상태를 모니터링할 수 있으므로 전화기 간의 프레즌스 정보가 활성화됩니다.
참고: 이 구성은 선택 사항입니다.
이 전화기는 Cisco Unified Communications Manager Express에서 SIP 프레즌스 서비스를 지원합니다.
제한 사항
BLF Call-List Supported only on Cisco Unified IP Phone 7941G, 7941GE, 7961G, 7961GE, 7970G, and 7971GE. BLF Speed-Dial Supported only on Cisco Unified IP Phone 7941G, 7941GE, 7961G, 7961GE, 7970G, and 7971GE.
내부 회선에 대한 프레즌스 사용
라우터가 내부 감시자 및 SIP 트렁크의 수신 프레즌스 요청을 수락하도록 하려면 다음 단계를 완료하십시오.
1. enable 2. configure terminal 3. sip-ua 4. presence enable 5. exit 6. presence 7. max-subscription number 8. presence call-list 9. end
내부 회선에 대한 프레즌스 사용 |
---|
Presence !--- Enable presence service. presence call-list !--- Enable BLF monitoring of directory numbers. max-subscription 120 !--- Configure max number watched sessions. ! sip-ua presence enable !--- Enable router to accept incoming presence request. |
감시할 디렉터리 번호 사용
디렉토리 번호와 연결된 회선을 Cisco Unified Communications Express 라우터에 등록된 전화기에서 모니터링하려면 다음 단계를 완료하십시오. 회선은 사전 엔터티로 활성화되어 있으며 전화기는 BLF 통화 목록 및 BLG 단축 다이얼 기능을 통해 회선 상태에 가입할 수 있습니다. 회선을 모니터링할 수 있는 전화기 유형에는 제한이 없습니다. 지원되는 음성 게이트웨이의 IP 전화 또는 아날로그 전화에 있는 모든 회선은 사전 엔터티일 수 있습니다.
1. enable 2. configure terminal 3. voice register dn dn-tag 4. number number 5. allow watch 6. end
감시할 디렉터리 번호 사용 |
---|
voice register dn 1 number 101 allow watch !--- Allow this number to be watched. name Phone1 label 4085251001 |
참고: 확인해야 할 각 내선 번호에 대해 이 컨피그레이션을 반복합니다. 이 단계는 처음 음성 레지스터 dns를 구성할 때 이미 수행되었습니다.
단축 다이얼 및 통화 목록에 대한 BLF 상태를 모니터링하도록 SIP Phone 활성화
감시자는 BLF 단축 다이얼 및 BLF 통화 목록 프레즌스 기능을 통해 내부 및 외부 디렉터리 번호(preentity)와 연결된 회선의 상태를 모니터링할 수 있습니다. SIP 전화에서 BLF 알림 기능을 활성화하려면 다음 단계를 완료하십시오.
1. enable 2. configure terminal 3. voice register pool pool-tag 4. number tag dn dn-tag 5. blf-speed-dial tag number label string 6. presence call-list 7. exit 8. voice register global 9. mode cme 10. create profile 11. restart 12. end
단축 다이얼 및 통화 목록에 대한 BLF 상태를 모니터링하도록 SIP Phone 활성화 |
---|
voice register pool 1 id mac 0016.47CD.9BD7 type 7970 number 1 dn 1 presence call-list !--- Enable this phone to have presence call list. dtmf-relay sip-notify username user1 password cisco codec g711ulaw blf-speed-dial 2 102 label "Phone2" !--- Enable this line to monitor extension 1002. blf-speed-dial 3 103 label "3911-1" !--- Enable this line to monitor extension 1003. blf-speed-dial 4 104 label "3911-2" !--- Enable this line to monitor extension 1004. |
참고: SIP Phone 컨피그레이션을 변경할 때마다 다시 시작을 수행해야 합니다.
참고: SIP Presence Service의 컨피그레이션에 대한 자세한 내용은 How to Configure Presence Service를 참조하십시오.
이 섹션에서, 연장들(102, 103, 및 104)은 병렬 헌트 그룹으로 할당된다. 병렬 헌트 그룹은 그룹의 모든 구성원을 동시에 호출하는 헌트 그룹입니다.
병렬 헌트 그룹 컨피그레이션 |
---|
voice hunt-group 1 pilot 180 !--- Configure Hunt group pilot number. list 102, 103, 104 !--- Specify members in hunt-group. final 100 !--- Specify final number as Voicemail Pilot. |
이 섹션에서는 SIP 전화를 사용하는 독립형 Cisco Unified Communications Manager Express를 설정하기 위한 전체 샘플 컨피그레이션을 제공합니다.
CME- SIP 구현: 샘플 설정 |
---|
CME-SIP#show version Cisco IOS Software, 2801 Software (C2801-IPVOICE-M), Version 12.4(11)XW2, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2007 by Cisco Systems, Inc. Compiled Mon 02-Jul-07 19:10 by prod_rel_team ROM: System Bootstrap, Version 12.3(8r)T6, RELEASE SOFTWARE (fc1) CME-SIP uptime is 18 hours, 55 minutes System returned to ROM by reload at 17:01:34 UTC Wed Oct 3 2007 System image file is "flash:c2801-ipvoice-mz.124-11.XW2.bin" Cisco 2801 (revision 4.1) with 235520K/26624K bytes of memory. Processor board ID FHK084510HS 11 FastEthernet interfaces 1 terminal line 2 Voice FXO interfaces 3 DSPs, 48 Voice resources 1 cisco service engine(s) DRAM configuration is 64 bits wide with parity disabled. 191K bytes of NVRAM. 62720K bytes of ATA CompactFlash (Read/Write) Configuration register is 0x2102 CME-SIP#show running-config Building configuration... Current configuration : 6227 bytes ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname CME-SIP ! boot-start-marker boot-end-marker ! logging buffered 999999 no logging console enable password cisco ! no aaa new-model ip cef ! ! no ip dhcp use vrf connected ip dhcp excluded-address 10.10.10.1 10.10.10.10 ip dhcp excluded-address 192.168.10.1 192.168.10.10 ! ip dhcp pool data network 10.10.10.0 255.255.255.0 default-router 10.10.10.1 ! ip dhcp pool voice network 192.168.10.0 255.255.255.0 option 150 ip 192.168.10.1 default-router 192.168.10.1 ! ! no ip domain lookup multilink bundle-name authenticated ! ! ! voice service voip allow-connections sip to sip sip registrar server expires max 1200 min 300 ! ! ! ! ! voice register global mode cme source-address 192.168.10.1 port 5060 max-dn 20 max-pool 10 load 7970 SIP70.8-2-1S load 3911 SIP3951.8-0-2-9 authenticate register authenticate realm cisco.com voicemail 100 tftp-path flash: create profile sync 0000589556325309 ! voice register dn 1 number 101 call-forward b2bua noan 100 timeout 20 allow watch name Phone1 label 4085251001 ! voice register dn 2 number 102 call-forward b2bua noan 100 timeout 20 allow watch name Phone2 label 4085251002 ! voice register dn 3 number 103 call-forward b2bua noan 100 timeout 20 allow watch name Phone3 label 4085251003 ! voice register dn 4 number 104 call-forward b2bua noan 100 timeout 20 allow watch name Phone4 label 4085251004 ! voice register pool 1 id mac 0016.47CD.9BD7 type 7970 number 1 dn 1 presence call-list dtmf-relay sip-notify username user1 password cisco codec g711ulaw blf-speed-dial 2 102 label "Phone2" blf-speed-dial 3 103 label "3911-1" blf-speed-dial 4 104 label "3911-2" ! voice register pool 2 id mac 0014.6948.1D52 type 7970 number 1 dn 2 dtmf-relay sip-notify username user2 password cisco codec g711ulaw ! voice register pool 3 id mac 001A.A11B.4FCE type 3911 number 1 dn 3 dtmf-relay sip-notify username user3 password cisco codec g711ulaw ! voice register pool 4 id mac 001A.A11B.500E type 3911 number 1 dn 4 dtmf-relay sip-notify username user4 password cisco codec g711ulaw ! voice hunt-group 1 parallel final 100 list 102,103,104 pilot 180 ! ! ! ! voice-card 0 ! ! ! archive log config hidekeys ! ! ! interface Loopback0 ip address 10.1.10.2 255.255.255.0 ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface Service-Engine0/0 ip unnumbered Loopback0 service-module ip address 10.1.10.1 255.255.255.0 service-module ip default-gateway 10.1.10.2 ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface FastEthernet0/3/0 description 7970 Phone switchport trunk native vlan 100 switchport mode trunk switchport voice vlan 192 spanning-tree portfast ! interface FastEthernet0/3/1 description 7970 Phone switchport trunk native vlan 100 switchport mode trunk switchport voice vlan 192 spanning-tree portfast ! interface FastEthernet0/3/2 description 3911 Phone switchport trunk native vlan 100 switchport mode trunk switchport voice vlan 192 spanning-tree portfast ! interface FastEthernet0/3/3 description 3911 Phone switchport trunk native vlan 100 switchport mode trunk switchport voice vlan 192 spanning-tree portfast ! interface FastEthernet0/3/4 description Phone switchport trunk native vlan 100 switchport mode trunk switchport voice vlan 192 spanning-tree portfast ! interface FastEthernet0/3/5 description Phone switchport trunk native vlan 100 switchport mode trunk switchport voice vlan 192 spanning-tree portfast ! interface FastEthernet0/3/6 description Phone switchport access vlan 192 switchport trunk native vlan 100 switchport mode trunk switchport voice vlan 192 spanning-tree portfast ! interface FastEthernet0/3/7 description Phone switchport access vlan 192 switchport trunk native vlan 100 switchport mode trunk switchport voice vlan 192 spanning-tree portfast ! interface FastEthernet0/3/8 switchport access vlan 192 ! interface Vlan1 no ip address ! interface Vlan100 ip address 10.10.10.1 255.255.255.0 ! interface Vlan192 ip address 192.168.10.1 255.255.255.0 ! ip route 10.1.10.1 255.255.255.255 Service-Engine0/0 ! ! ip http server ! ! ! tftp-server flash:BOOT3951.0-0-0-9.zz tftp-server flash:SIP3951.8-0-2-9.zz tftp-server flash:DSP3951.0-0-0-1.zz tftp-server flash:SIP3951.8-0-2-9.loads tftp-server flash:SIP70.8-2-1S.loads tftp-server flash:term70.default.loads tftp-server flash:term71.default.loads tftp-server flash:apps70.8-0-2-55.sbn tftp-server flash:cnu70.8-2-0-55.sbn tftp-server flash:cvm70.sip.8-2-0-55.sbn tftp-server flash:dsp70.8-2-0-55.sbn tftp-server flash:jar70.sip.8-0-2-25.sbn ! control-plane ! ! ! voice-port 0/1/0 ! voice-port 0/1/1 ! ! ! ! ! dial-peer voice 2 voip description ** cue voicemail pilot number ** translation-profile outgoing PSTN_CallForwarding destination-pattern 100 b2bua session protocol sipv2 session target ipv4:10.1.10.1 dtmf-relay sip-notify codec g711ulaw no vad ! dial-peer voice 3 voip description ** cue auto attendant number ** translation-profile outgoing PSTN_CallForwarding destination-pattern 110 b2bua session protocol sipv2 session target ipv4:10.1.10.1 dtmf-relay sip-notify codec g711ulaw no vad ! ! presence presence call-list max-subscription 120 ! sip-ua presence enable ! ! telephony-service max-ephones 24 max-dn 72 ip source-address 10.100.100.10 port 2000 system message CME1 time-zone 5 voicemail 100 max-conferences 8 gain -6 call-forward pattern .T web admin system name cisco secret 5 $1$4FC/$CMer08o/KELFlVrhL5QRO0 dn-webedit time-webedit transfer-system full-blind transfer-pattern 9.T ! ! ephone-dn 11 number 800 mwi on ! ! ephone-dn 12 number 801 mwi off ! ! line con 0 line aux 0 line 66 no activation-character no exec transport preferred none transport input all transport output pad telnet rlogin lapb-ta mop udptn v120 line vty 0 4 password cisco login ! scheduler allocate 20000 1000 end CME-SIP# |
현재 이 설정에 사용 가능한 확인 절차는 없습니다.
이 섹션에서는 설정 문제 해결에 사용할 수 있는 정보를 제공합니다.
SIP IP Phone에서 신호음을 수신할 수 없는 일반적인 원인은 동일한 내선 번호의 다른 전화기가 있기 때문입니다. Cisco Unified Communications Manager Express 4.2부터는 공유 회선이 SIP 전화기에서 지원되지 않습니다. 따라서 SIP 전화기는 여러 전화기 간에 동일한 내선 번호를 공유할 수 없습니다. 또한 SIP 전화기가 적절한 내선 번호로 프로비저닝되었는지 확인합니다.
이 문제를 해결하려면 다음 사항이 발생하는지 확인하십시오.
SIP 전화기에 내선 번호가 구성되어 있으며 내선 번호가 SIP 전화기에 표시됩니다.
동일한 내선 번호로 구성된 다른 SIP 또는 SCCP 전화기가 없습니다.
전화기를 업그레이드하지 못할 수 있는 가장 큰 원인은 Cisco Unified Communications Manager Express 플래시에 있는 펌웨어 파일 누락 또는 tftp-server 명령 누락
이 문제를 해결하려면 다음 단계를 수행하십시오.
필요한 펌웨어 파일이 플래시에 저장되어 있는지 확인합니다. dir 플래시를 수행합니다. 플래시에서 파일을 검사하기 위한 명령입니다.
OS79XX.TXT 파일을 업데이트하여 올바른 펌웨어를 적용했는지 확인합니다. 79XX 전화기는 적절한 펌웨어를 로드하고 SCCP에서 SIP로 변경하기 위해 이 파일을 확인합니다.
각 펌웨어 파일에 올바른 tftp-server 문이 추가되었는지 확인합니다. TFTP 구성 섹션을 참조하십시오.
각 SIP 전화의 유형에 대해 voice register global의 load 명령이 추가되었는지 확인합니다. Configure Voice Register Global Parameters(음성 레지스터 전역 매개변수 구성) 섹션을 참조하십시오.
추가 문제를 해결하려면 이러한 디버그를 수집하여 전화기가 Cisco Unified Communications Manager Express 플래시에서 적절한 전화기 로드를 가져올 수 있는지 확인합니다.
Debug tftp events
전화기를 프로비저닝할 수 없는 가장 큰 원인은 전화기에 TFTP 서버 옵션이 있는 적절한 IP 주소가 없기 때문입니다.
전화기에서 IP 주소 및 적절한 TFTP 서버 IP 주소를 수신하는지 확인합니다.
모든 적절한 voice register 전역 명령이 추가되었는지 확인합니다. Configure Voice Register Global Parameters(음성 레지스터 전역 매개변수 구성) 섹션을 참조하십시오.
각 음성 레지스터 풀 컨피그레이션 아래에 올바른 MAC 주소를 사용하는지 확인합니다.
개정 | 게시 날짜 | 의견 |
---|---|---|
1.0 |
05-Nov-2007 |
최초 릴리스 |