VCS Series 또는 Expressway Series Xconfig 및 Xstatus Output Collection with PuTTY

다운로드 옵션

PDF (789.2 KB)
다양한 디바이스에서 Adobe Reader로 보기
ePub (400.0 KB)
iPhone, iPad, Android, Sony Reader 또는 Windows Phone의 다양한 앱에서 보기
Mobi (Kindle) (450.1 KB)
Kindle 디바이스에서 보기 또는 다양한 디바이스의 Kindle 앱에서 보기

업데이트:2014년 12월 15일

문서 ID:118675

편견 없는 언어

본 제품에 대한 문서 세트는 편견 없는 언어를 사용하기 위해 노력합니다. 본 설명서 세트의 목적상, 편견 없는 언어는 나이, 장애, 성별, 인종 정체성, 민족 정체성, 성적 지향성, 사회 경제적 지위 및 교차성에 기초한 차별을 의미하지 않는 언어로 정의됩니다. 제품 소프트웨어의 사용자 인터페이스에서 하드코딩된 언어, RFP 설명서에 기초한 언어 또는 참조된 서드파티 제품에서 사용하는 언어로 인해 설명서에 예외가 있을 수 있습니다. 시스코에서 어떤 방식으로 포용적인 언어를 사용하고 있는지 자세히 알아보세요.

이 번역에 관하여

Cisco는 전 세계 사용자에게 다양한 언어로 지원 콘텐츠를 제공하기 위해 기계 번역 기술과 수작업 번역을 병행하여 이 문서를 번역했습니다. 아무리 품질이 높은 기계 번역이라도 전문 번역가의 번역 결과물만큼 정확하지는 않습니다. Cisco Systems, Inc.는 이 같은 번역에 대해 어떠한 책임도 지지 않으며 항상 원본 영문 문서(링크 제공됨)를 참조할 것을 권장합니다.

소개

이 문서에서는 VCS-Control, VCS-Expressway, Expressway-C 및 Expressway-E와 같은 Expressway Series 디바이스에서 xconfig 및 xstatus xcommands의 CLI 출력을 수집하여 Cisco TAC(Technical Assistance Center)에서 가끔 검색해야 하는 방법에 대해 설명합니다.

사전 요구 사항

요구 사항

다음 주제에 대한 지식을 보유하고 있으면 유용합니다.

PuTTY 또는 SecureCRT, Tera Term 등과 같은 유사한 터미널 에뮬레이션 소프트웨어
VCS/Expressway 시리즈 디바이스에 대한 관리자 계정 사용자 이름 및 비밀번호
네트워크 경로에 허용되는 RJ45-D-Sub9pin Serial Console Cable 또는 SSH(Secure Shell)

사용되는 구성 요소

이 문서의 정보는 다음 소프트웨어 및 하드웨어 버전을 기반으로 합니다.

PuTTY(사본을 얻으려면 PuTTY 다운로드 페이지를 방문하십시오.)
버전 7.2.1을 실행하는 VCS-C는 현재 최신 버전인 버전 8.2.2을 통해 적용할 수 있는 이 예제에 사용됩니다.

구성

콘솔로 연결

참고: 이 문서에서는 기능 물리적 직렬 콘솔 케이블이 연결되어 있다고 가정합니다. 디바이스와 함께 수신해야 합니다.

다음은 PuTTY에서 직렬 콘솔 액세스를 위해 구성해야 하는 설정의 예입니다.

참고: 콘솔이 PC에 연결된 방식에 따라 통신(COM) 포트를 조정해야 합니다.

Configuration(컨피그레이션) > Category(카테고리) > Connection(연결) > Serial(시리얼)으로 이동하여 다음과 같이 시리얼 설정을 조정합니다.
Category(카테고리) > Session(세션)으로 이동하여 Serial type(시리얼 유형)을 연결 유형으로 선택하고 여기에 표시된 대로 Open(열기)을 클릭합니다.

SSH를 통해 연결

더 간단한 방법은 디바이스에 SSH를 설치하는 것입니다.

다음 예와 같이 PuTTY에서 설정을 조정하려면 VCS/Expressway 디바이스의 IP 주소를 사용합니다.
디바이스에 대한 PuTTY 세션 이전 또는 도중 Logging Settings(로깅 설정)를 설정해야 합니다. 이렇게 하려면 Configuration(구성) > Category(범주) > Session(세션) > Logging(로깅)으로 이동하여 이 예와 일치하도록 설정을 구성합니다(파일 경로와 파일 이름을 사용자 PC 및 필요에 맞게 조정).
연결되고 로그인하면 이 화면과 유사한 화면이 표시됩니다. 여기에 표시된 대로 관리자로 로그인하십시오.

주의: 랩 환경이므로 경보를 무시할 수 있습니다. 프로덕션 환경에서 경보가 발생하면 최대한 빨리 처리해야 합니다.
xstatus 명령을 입력하고 Enter 키를 누릅니다.

다음은 Enter를 누른 후 표시되는 xstatus 출력입니다. 출력이 너무 빨리 지나가버려서 끝까지 볼 수 없습니다. 이전에 로깅을 구성한 경우 텍스트 파일에 기록됩니다.

xstatus 명령의 출력을 수집했으므로 xconfig 명령의 출력을 수집할 준비가 되었습니다.
xconfig 명령을 입력하고 Enter를 누릅니다.

다음은 Enter 키를 누른 후 xconfig 출력의 예입니다. 출력이 너무 빠르게 지나가서 끝까지 볼 수 없습니다. 이전에 로깅을 구성한 경우 텍스트 파일에 기록됩니다.

VCS 및 Expressway Series x8.2

x8.2의 소프트웨어 릴리스에서는 진단 로그를 생성할 때 xconfiguration 및 xstatus가 포함됩니다.

Maintenance(유지 관리) > Diagnostics(진단) > Diagnostic logging(진단 로깅)으로 이동합니다.
Start new log(새 로그 시작)를 선택한 다음 즉시 Stop logging(로깅 중지)을 선택합니다.

참고: 또한 이 방법에는 VCS 또는 Expressway Series에서 발생하는 활동에 대한 응답으로 메시지를 로깅하는 loggingsnapshot.txt가 포함되어 있습니다.

다운로드한 진단 로그 아카이브에는 다음 파일이 포함됩니다.
- loggingsnapshot.txt - 로깅 기간 동안 수행된 활동에 대한 응답으로 로그 메시지를 포함합니다.
- xconf_dump.txt - 로깅 시작 시 시스템 구성에 대한 정보가 들어 있습니다.
- xstat_dump.txt - 로깅이 시작될 때의 시스템 상태에 대한 정보를 포함합니다.
- (해당되는 경우) diagnostic_logging_tcpdump.pcap - 로깅 기간 동안 캡처된 패킷을 포함합니다.

다음을 확인합니다.

다음은 로깅 설정으로 저장된 텍스트 파일에서 xstatus 및 xconfig 출력이 어떻게 표시되는지 보여주는 예입니다.

xstatus

*s SystemUnit:
     Product: "TANDBERG VCS"
     Uptime: 24963390
     SystemTime: "2014-06-19 14:58:59"
     TimeZone: "US/Eastern"
     LocalTime: "2014-06-19 10:58:59"
     Software:
       Version: "X7.2.1"
       Build: "296181"
       Name: "s42700"
       ReleaseDate: "2012-09-25"
       ReleaseKey: "****************"
       Configuration:
         NonTraversalCalls: 500
         TraversalCalls: 200
         Registrations: 2500
         Expressway: False
         Encryption: True
         Interworking: True
         FindMe: True
         DeviceProvisioning: True
         DualNetworkInterfaces: False
         AdvancedAccountSecurity: False
         StarterPack: False
         EnhancedOCSCollaboration: True
     Hardware:
       Version: "VMWare"
       SerialNumber: "********"
*s/end

*s Ethernet 1:
     MacAddress: "00:50:56:A1:70:06"
     Speed: 10000full
     IPv4:
       Address: "10.10.10.10"
       SubnetMask: "255.255.255.0"
*s/end

*s Ethernet 2:
     MacAddress: "00:50:56:A1:70:04"
     Speed: 10000full
     IPv4:
       Address: "192.168.0.100"
       SubnetMask: "255.255.255.0"
*s/end

*s Options:
     Option 1:
       Key: "116341X300-1-!!!!!!!!"
       Description: "300 Non-traversal Calls"
     Option 2:
       Key: "116341P00-1-!!!!!!!!"
       Description: "Device Provisioning"
     Option 3:
       Key: "116341G00-1-!!!!!!!!!"
       Description: "H323-SIP Interworking Gateway"
     Option 4:
       Key: "116341U00-1-!!!!!!!!!"
       Description: "FindMe"
     Option 5:
       Key: "116341C00-1-!!!!!!!!!"
       Description: "Enhanced OCS Collaboration"
     Option 8:
       Key: "116341Y200-1-!!!!!!!!"
       Description: "200 Traversal Calls"
     Option 9:
       Key: "116341X200-1-!!!!!!!!"
       Description: "200 Non-traversal Calls"
*s/end

*s IP:
     Protocol: IPv4
     IPv4:
       Gateway: "10.10.10.1"
*s/end

*s ExternalManager:
     Status: Active
     Address: "10.10.10.104"
     Protocol: HTTP
     URL: "tms/public/external/management/systemmanagementservice.asmx"
*s/end

*s Feedback 1:
     Status: Off
*s/end

*s Feedback 2:
     Status: Off
*s/end

*s Feedback 3:
     Status: On
     URL: "http://10.10.10.104/tms/public/feedback/code.aspx"
     Expression: "/Event/CallDisconnected"
     Expression: "/Event/CallConnected"
     Expression: "/Event/CallFailure"
     Expression: "/Event/RegistrationAdded"
     Expression: "/Event/RegistrationChanged"
     Expression: "/Event/ResourceUsage"
     Expression: "/Event/AuthenticationFailure"
     Expression: "/Status/Warnings"
*s/end

*s ResourceUsage:
     Calls:
       Traversal:
         Current: 0
         Max: 0
         Total: 0
       NonTraversal:
         Current: 0
         Max: 1
         Total: 2
     Registrations:
       Current: 0
       Max: 3
       Total: 42
*s/end

*s Calls: /
*s/end

*s Zones:
     DefaultZone:
       Name: "DefaultZone"
       Bandwidth:
         LocalUsage: 0
         ClusterUsage: 0
     LocalZone:
       DefaultSubZone:
         Name: "DefaultSubZone"
         Bandwidth:
           LocalUsage: 0
           ClusterUsage: 0
       TraversalSubZone:
         Name: "TraversalSubZone"
         Bandwidth:
           LocalUsage: 0
           ClusterUsage: 0
       ClusterSubZone:
         Name: "ClusterSubZone"
         Bandwidth:
           LocalUsage: 0
           ClusterUsage: 0
     Searches:
       Current: 0
       CurrentDirected: 0
       Total: 64081
       Dropped: 0
       MaxSubSearchExceeded: 0
       MaxTargetsExceeded: 0
     Zone 1:
       Name: "TraversalZone"
       Bandwidth:
         LocalUsage: 0
         ClusterUsage: 0
       Status: Active
       Type: TraversalClient
       TraversalClient:
         Peer 1:
           H323:
             Status: Active
             Address: "10.10.10.102"
             Port: 6001
             LastStatusChange: "2014-04-03 09:50:35"
           SIP:
             Status: Active
             Address: "10.10.10.102"
             Port: 7001
             LastStatusChange: "2014-04-03 09:49:13"
             Server: "TANDBERG/4102 (X7.0)"
*s/end

*s Alternates: /
*s/end

*s Links:
     Link 1:
       Name: "DefaultSZtoTraversalSZ"
       Bandwidth:
         LocalUsage: 0
         ClusterUsage: 0
     Link 2:
       Name: "DefaultSZtoDefaultZ"
       Bandwidth:
         LocalUsage: 0
         ClusterUsage: 0
     Link 3:
       Name: "DefaultSZtoClusterSZ"
       Bandwidth:
         LocalUsage: 0
         ClusterUsage: 0
     Link 4:
       Name: "TraversalSZtoDefaultZ"
       Bandwidth:
         LocalUsage: 0
         ClusterUsage: 0
     Link 5:
       Name: "Zone001ToTraversalSZ"
       Bandwidth:
         LocalUsage: 0
         ClusterUsage: 0
*s/end

*s Pipes: /
*s/end

*s Registrations: /
*s/end

*s SIP:
     Ethernet 1:
       IPv4:
         UDP:
           Status: Inactive
         TCP:
           Status: Active
           Address: "10.10.10.10:5060"
         TLS:
           Status: Active
           Address: "10.10.10.10:5061"
       IPv6:
         UDP:
           Status: Inactive
         TCP:
           Status: Inactive
         TLS:
           Status: Inactive
     Ethernet 2:
       IPv4:
         UDP:
           Status: Inactive
         TCP:
           Status: Inactive
         TLS:
           Status: Inactive
       IPv6:
         UDP:
           Status: Inactive
         TCP:
           Status: Inactive
         TLS:
           Status: Inactive
     Transport:
       Server 19857:
         Socket:
           Type: "SERV_UDP"
           State: "INUSE"
           ID:
             Local: 85393
             Global: 0
           Buffer:
             Input:
               Length: 20000
             Output:
               Length: 20000
         Local:
           Address: "127.0.0.1:5060"
         Remote:
           Address: ""
         Network:
           Number: 1
         Certificate:
           Subject:
             Name: ""
         TLS:
           Cipher:
             Name: ""
         Last:
           Packet:
             Received: 0
         Close:
           In: 20
         Secure: False
         X509:
           Certificate:
             Verified: False
         Queue:
           Max:
             Size: 0
           Add:
             Failures: 0
         Flow:
           Token: ""
       Server 19856:
         Socket:
           Type: "SERV_TCP"
           State: "INUSE"
           ID:
             Local: 150928
             Global: 1
           Buffer:
             Input:
               Length: 0
             Output:
               Length: 0
         Local:
           Address: "127.0.0.1:5060"
         Remote:
           Address: ""
         Network:
           Number: 1
         Certificate:
           Subject:
             Name: ""
         TLS:
           Cipher:
             Name: ""
         Last:
           Packet:
             Received: 0
         Close:
           In: 20
         Secure: False
         X509:
           Certificate:
             Verified: False
         Queue:
           Max:
             Size: 0
           Add:
             Failures: 0
         Flow:
           Token: ""
       Server 19855:
         Socket:
           Type: "SERV_TLS"
           State: "INUSE"
           ID:
             Local: 216463
             Global: 2
           Buffer:
             Input:
               Length: 0
             Output:
               Length: 0
         Local:
           Address: "127.0.0.1:5061"
         Remote:
           Address: ""
         Network:
           Number: 1
         Certificate:
           Subject:
             Name: ""
         TLS:
           Cipher:
             Name: ""
         Last:
           Packet:
             Received: 0
         Close:
           In: 20
         Secure: True
         X509:
           Certificate:
             Verified: False
         Queue:
           Max:
             Size: 0
           Add:
             Failures: 0
         Flow:
           Token: ""
       Server 19854:
         Socket:
           Type: "SERV_UDP"
           State: "INUSE"
           ID:
             Local: 281998
             Global: 3
           Buffer:
             Input:
               Length: 20000
             Output:
               Length: 20000
         Local:
           Address: "[::1]:5060"
         Remote:
           Address: ""
         Network:
           Number: 1
         Certificate:
           Subject:
             Name: ""
         TLS:
           Cipher:
             Name: ""
         Last:
           Packet:
             Received: 0
         Close:
           In: 20
         Secure: False
         X509:
           Certificate:
             Verified: False
         Queue:
           Max:
             Size: 0
           Add:
             Failures: 0
         Flow:
           Token: ""
       Server 19853:
         Socket:
           Type: "SERV_TCP"
           State: "INUSE"
           ID:
             Local: 347533
             Global: 4
           Buffer:
             Input:
               Length: 0
             Output:
               Length: 0
         Local:
           Address: "[::1]:5060"
         Remote:
           Address: ""
         Network:
           Number: 1
         Certificate:
           Subject:
             Name: ""
         TLS:
           Cipher:
             Name: ""
         Last:
           Packet:
             Received: 0
         Close:
           In: 20
         Secure: False
         X509:
           Certificate:
             Verified: False
         Queue:
           Max:
             Size: 0
           Add:
             Failures: 0
         Flow:
           Token: ""
       Server 19852:
         Socket:
           Type: "SERV_TLS"
           State: "INUSE"
           ID:
             Local: 413068
             Global: 5
           Buffer:
             Input:
               Length: 0
             Output:
               Length: 0
         Local:
           Address: "[::1]:5061"
         Remote:
           Address: ""
         Network:
           Number: 1
         Certificate:
           Subject:
             Name: ""
         TLS:
           Cipher:
             Name: ""
         Last:
           Packet:
             Received: 0
         Close:
           In: 20
         Secure: True
         X509:
           Certificate:
             Verified: False
         Queue:
           Max:
             Size: 0
           Add:
             Failures: 0
         Flow:
           Token: ""
       Server 19851:
         Socket:
           Type: "SERV_TCP"
           State: "INUSE"
           ID:
             Local: 478603
             Global: 6
           Buffer:
             Input:
               Length: 0
             Output:
               Length: 0
         Local:
           Address: "10.10.10.10:5060"
         Remote:
           Address: ""
         Network:
           Number: 2
         Certificate:
           Subject:
             Name: ""
         TLS:
           Cipher:
             Name: ""
         Last:
           Packet:
             Received: 0
         Close:
           In: 20
         Secure: False
         X509:
           Certificate:
             Verified: False
         Queue:
           Max:
             Size: 0
           Add:
             Failures: 0
         Flow:
           Token: ""
       Server 19850:
         Socket:
           Type: "SERV_TLS"
           State: "INUSE"
           ID:
             Local: 544138
             Global: 7
           Buffer:
             Input:
               Length: 0
             Output:
               Length: 0
         Local:
           Address: "10.10.10.10:5061"
         Remote:
           Address: ""
         Network:
           Number: 2
         Certificate:
           Subject:
             Name: ""
         TLS:
           Cipher:
             Name: ""
         Last:
           Packet:
             Received: 0
         Close:
           In: 20
         Secure: True
         X509:
           Certificate:
             Verified: False
         Queue:
           Max:
             Size: 0
           Add:
             Failures: 0
         Flow:
           Token: ""
       Client 7747:
         Socket:
           Type: "TLS_OUTG"
           State: "INUSE"
           ID:
             Local: 825433667
             Global: 654
           Buffer:
             Input:
               Length: 5120
             Output:
               Length: 20000
         Local:
           Address: "10.10.10.10:27573"
         Remote:
           Address: "10.10.10.102:7001"
         Network:
           Number: 2
         Certificate:
           Subject:
             Name: ""
         TLS:
           Cipher:
             Name: "DHE-RSA-AES256-SHA"
         Last:
           Packet:
             Received: -1798628722
         Close:
           In: 900
         Secure: True
         X509:
           Certificate:
             Verified: False
         Queue:
           Max:
             Size: 1
           Add:
             Failures: 0
         Flow:
           Token: ""
*s/end

*s H323:
     Registration:
       Status: Active
       IPv4:
         Address: "10.10.10.10:1719"
     CallSignaling:
       Status: Active
       IPv4:
         Address: "10.10.10.10:1720"
     Assent:
       CallSignaling:
         Status: Inactive
     H46018:
       CallSignaling:
         Status: Inactive
*s/end

*s Applications:
     Presence:
       UserAgent:
         Status: Inactive
         Presentity:
           Count: 0
       Server:
         Subscriptions:
           Count: 0
           Max: 0
           Expired: 0
           Subscribers:
             Count: 0
             Max: 0
         Status: Inactive
         Presentities:
           Count: 0
           Max: 0
         Publications:
           Presentities:
             Count: 0
             Max: 0
     ConferenceFactory:
       Status: Inactive
       NextAlias: ""
     External 1:
       Status:
         ClusterStatus:
           ClusterState: "Disabled"
       LastUpdate:
         Time: "Time not set"
         SecondsSinceLastRefresh: "1403189939"
*s/end

*s FindMeManager: /
*s/end

*s TURN:
     Server:
       Status: Inactive
*s/end

*s Policy: /
*s/end

OK






























xcommand xconfig
*c xConfiguration Login Remote Protocol: LDAP
*c xConfiguration Login Remote LDAP Server Address: ""
*c xConfiguration Login Remote LDAP Server FQDNResolution: AddressRecord
*c xConfiguration Login Remote LDAP Server Port: 389
*c xConfiguration Login Remote LDAP VCS BindUsername: ""
*c xConfiguration Login Remote LDAP VCS BindPassword: "{cipher}XXXXXXXXXX
XXXXXXXXXXXX"
*c xConfiguration Login Remote LDAP VCS BindDN: ""
*c xConfiguration Login Remote LDAP BaseDN Accounts: ""
*c xConfiguration Login Remote LDAP BaseDN Groups: ""
*c xConfiguration Login Remote LDAP Encryption: Off
*c xConfiguration Login Remote LDAP SASL: DIGEST-MD5
*c xConfiguration Login Remote LDAP CRLCheck: None
*c xConfiguration Login Remote LDAP DirectoryType: ActiveDirectory
*c xConfiguration SystemUnit Name: "VCS1-Control"
*c xConfiguration SystemUnit Maintenance Mode: Off
*c xConfiguration Option 1 Key: "116341X300-1-!!!!!!!!"
*c xConfiguration Option 2 Key: "116341P00-1-!!!!!!!!"
*c xConfiguration Option 3 Key: "116341G00-1-!!!!!!!!!"
*c xConfiguration Option 4 Key: "116341U00-1-!!!!!!!!!"
*c xConfiguration Option 5 Key: "116341C00-1-!!!!!!!!"
*c xConfiguration Option 8 Key: "116341Y200-1-!!!!!!!!"
*c xConfiguration Option 9 Key: "116341X200-1-!!!!!!!!"
*c xConfiguration Ethernet 1 Speed: Auto
*c xConfiguration Ethernet 1 IP V4 Address: "10.10.10.10"
*c xConfiguration Ethernet 1 IP V4 SubnetMask: "255.255.255.0"
*c xConfiguration Ethernet 1 IP V6 Address: ""
*c xConfiguration Ethernet 2 Speed: Auto
*c xConfiguration Ethernet 2 IP V4 Address: "192.168.0.100"
*c xConfiguration Ethernet 2 IP V4 SubnetMask: "255.255.255.0"
*c xConfiguration Ethernet 2 IP V6 Address: ""
*c xConfiguration IPProtocol: IPv4
*c xConfiguration IP Gateway: "10.10.10.1"
*c xConfiguration IP QoS Mode: None
*c xConfiguration IP QoS Value: 0
*c xConfiguration IP V6 Gateway: ""
*c xConfiguration IP DNS Domain Name: "######.local"
*c xConfiguration IP DNS Hostname: "VCS1-Control"
*c xConfiguration IP Ephemeral PortRange Start: 40000
*c xConfiguration IP Ephemeral PortRange End: 49999
*c xConfiguration IP RFC4821 Mode: Disabled
*c xConfiguration Administration Telnet Mode: Off
*c xConfiguration Administration SSH Mode: On
*c xConfiguration Administration HTTP Mode: On
*c xConfiguration Administration HTTPS Mode: On
*c xConfiguration Administration LCDPanel Mode: On
*c xConfiguration ExternalManager Address: "10.10.10.104"
*c xConfiguration ExternalManager Path: "tms/public/external/management/system
managementservice.asmx"
*c xConfiguration ExternalManager Protocol: HTTP
*c xConfiguration ExternalManager Server Certificate Verification Mode: On
*c xConfiguration Registration RestrictionPolicy Mode: None
*c xConfiguration Registration RestrictionPolicy Service Protocol: HTTP
*c xConfiguration Registration RestrictionPolicy Service TLS Verify Mode: On
*c xConfiguration Registration RestrictionPolicy Service TLS CRLCheck Mode: Off
*c xConfiguration Registration RestrictionPolicy Service Server 1 Address: ""
*c xConfiguration Registration RestrictionPolicy Service Server 2 Address: ""
*c xConfiguration Registration RestrictionPolicy Service Server 3 Address: ""
*c xConfiguration Registration RestrictionPolicy Service Path: ""
*c xConfiguration Registration RestrictionPolicy Service Status Path: "status"
*c xConfiguration Registration RestrictionPolicy Service UserName: ""
*c xConfiguration Registration RestrictionPolicy Service Password: "{cipher}
XXXXXXXXXXXXXXXXXXXXX"
*c xConfiguration Registration RestrictionPolicy Service DefaultCPL: "<reject 
status='504' reason='Registration Policy Unavailable'/>"
*c xConfiguration Alternates ConfigurationMaster: 1
*c xConfiguration Alternates Cluster Name: ""
*c xConfiguration Alternates Peer 1 Address: ""
*c xConfiguration Alternates Peer 2 Address: ""
*c xConfiguration Alternates Peer 3 Address: ""
*c xConfiguration Alternates Peer 4 Address: ""
*c xConfiguration Alternates Peer 5 Address: ""
*c xConfiguration Alternates Peer 6 Address: ""
*c xConfiguration Transform 1 Description: "Transform destination aliases to 
URI format"
*c xConfiguration Transform 1 State: Enabled
*c xConfiguration Transform 1 Priority: 1
*c xConfiguration Transform 1 Pattern String: "([^@]*)"
*c xConfiguration Transform 1 Pattern Type: Regex
*c xConfiguration Transform 1 Pattern Behavior: Replace
*c xConfiguration Transform 1 Pattern Replace: "\1@#####.local"
*c xConfiguration Call Loop Detection Mode: On
*c xConfiguration Call Routed Mode: Always
*c xConfiguration Call Services CallsToUnknownIPAddresses: Indirect
*c xConfiguration Call Services Fallback Alias: ""
*c xConfiguration H323 Mode: On
*c xConfiguration H323 Gatekeeper Registration UDP Port: 1719
*c xConfiguration H323 Gatekeeper Registration ConflictMode: Reject
*c xConfiguration H323 Gatekeeper CallSignaling TCP Port: 1720
*c xConfiguration H323 Gatekeeper CallSignaling PortRange Start: 15000
*c xConfiguration H323 Gatekeeper CallSignaling PortRange End: 19999
*c xConfiguration H323 Gatekeeper TimeToLive: 1800
*c xConfiguration H323 Gatekeeper CallTimeToLive: 120
*c xConfiguration H323 Gatekeeper AutoDiscovery Mode: On
*c xConfiguration H323 Gateway CallerId: ExcludePrefix
*c xConfiguration SIP Mode: On
*c xConfiguration SIP Domains Domain 1 Name: "######.com"
*c xConfiguration SIP Domains Domain 2 Name: "######.local"
*c xConfiguration SIP Routes Route 1 Method: "SUBSCRIBE"
*c xConfiguration SIP Routes Route 1 Request Line Pattern: ".*@(%localdomains%|
%ip%)"
*c xConfiguration SIP Routes Route 1 Header Name: "Event"
*c xConfiguration SIP Routes Route 1 Header Pattern: "(ua-profile|phonebook).*"
*c xConfiguration SIP Routes Route 1 Authenticated: Off
*c xConfiguration SIP Routes Route 1 Address: "127.0.0.1"
*c xConfiguration SIP Routes Route 1 Port: 22400
*c xConfiguration SIP Routes Route 1 Transport: TCP
*c xConfiguration SIP Routes Route 1 Tag: "Provisioning"
*c xConfiguration SIP Routes Route 2 Method: "INFO"
*c xConfiguration SIP Routes Route 2 Request Line Pattern: ".*@(%localdomains%|
%ip%)"
*c xConfiguration SIP Routes Route 2 Header Name: "Content-Type"
*c xConfiguration SIP Routes Route 2 Header Pattern: "application/tandberg-
phonebook\+xml"
*c xConfiguration SIP Routes Route 2 Authenticated: Off
*c xConfiguration SIP Routes Route 2 Address: "127.0.0.1"
*c xConfiguration SIP Routes Route 2 Port: 22400
*c xConfiguration SIP Routes Route 2 Transport: TCP
*c xConfiguration SIP Routes Route 2 Tag: "Phonebook"
*c xConfiguration SIP Registration Standard Refresh Strategy: Maximum
*c xConfiguration SIP Registration Standard Refresh Minimum: 45
*c xConfiguration SIP Registration Standard Refresh Maximum: 60
*c xConfiguration SIP Registration Outbound Refresh Strategy: Variable
*c xConfiguration SIP Registration Outbound Refresh Minimum: 300
*c xConfiguration SIP Registration Outbound Refresh Maximum: 3600
*c xConfiguration SIP Registration Outbound Flow Timer: 0
*c xConfiguration SIP Registration Proxy Mode: Off
*c xConfiguration SIP Registration Call Remove: No
*c xConfiguration SIP Session Refresh Value: 1800
*c xConfiguration SIP Session Refresh Minimum: 500
*c xConfiguration SIP UDP Mode: Off
*c xConfiguration SIP UDP Port: 5060
*c xConfiguration SIP TCP Mode: On
*c xConfiguration SIP TCP Port: 5060
*c xConfiguration SIP TCP Outbound Port Start: 25000
*c xConfiguration SIP TCP Outbound Port End: 29999
*c xConfiguration SIP TLS Mode: On
*c xConfiguration SIP TLS Port: 5061
*c xConfiguration SIP TLS Certificate Revocation Checking Mode: Off
*c xConfiguration SIP TLS Certificate Revocation Checking OCSP Mode: On
*c xConfiguration SIP TLS Certificate Revocation Checking CRL Mode: On
*c xConfiguration SIP TLS Certificate Revocation Checking CRL Network Fetch 
Mode: On
*c xConfiguration SIP TLS Certificate Revocation Checking Source Inaccessibility
 Behavior: Fail
*c xConfiguration SIP Require UDP BFCP Mode: On
*c xConfiguration SIP Require Duo Video Mode: On
*c xConfiguration SIP Authentication Retry Limit: 3
*c xConfiguration SIP Authentication NTLM Mode: Auto
*c xConfiguration SIP Authentication NTLM SA Lifetime: 28800
*c xConfiguration SIP Authentication NTLM SA Limit: 10000
*c xConfiguration SIP Authentication Digest Nonce ExpireDelta: 300
*c xConfiguration SIP Authentication Digest Nonce Maximum Use Count: 128
*c xConfiguration SIP Authentication Digest Nonce Limit: 10000
*c xConfiguration SIP Authentication Digest Nonce Length: 60
*c xConfiguration SIP GRUU Mode: On
*c xConfiguration SIP MediaRouting ICE Mode: Off
*c xConfiguration Interworking Mode: RegisteredOnly
*c xConfiguration Interworking Encryption Mode: Auto
*c xConfiguration Interworking Encryption Replay Protection Mode: Off
*c xConfiguration Interworking BFCP Compatibility Mode: Auto
*c xConfiguration Interworking Require Invite Header Mode: On
*c xConfiguration Traversal Media Port Start: 50000
*c xConfiguration Traversal Media Port End: 52399
*c xConfiguration Authentication UserName: ""
*c xConfiguration Authentication Password: "{cipher}XXXXXXXXXXXXXXXXXXXXXX"
*c xConfiguration Authentication LDAP AliasOrigin: LDAP
*c xConfiguration Authentication ADS ADDomain: ""
*c xConfiguration Authentication ADS Workgroup: ""
*c xConfiguration Authentication ADS MachinePassword Refresh: On
*c xConfiguration Authentication ADS SPNEGO: Enabled
*c xConfiguration Authentication ADS SecureChannel: Auto
*c xConfiguration Authentication ADS Encryption: TLS
*c xConfiguration Authentication ADS Mode: Off
*c xConfiguration Authentication ADS Clockskew: 300
*c xConfiguration Zones Policy Mode: SearchRules
*c xConfiguration Zones Policy SearchRules Rule 1 Name: "Local zone ? no domain"
*c xConfiguration Zones Policy SearchRules Rule 1 Description: "Search local 
zone for H.323 devices (strip domain)"
*c xConfiguration Zones Policy SearchRules Rule 1 Priority: 48
*c xConfiguration Zones Policy SearchRules Rule 1 Protocol: Any
*c xConfiguration Zones Policy SearchRules Rule 1 Source Mode: Any
*c xConfiguration Zones Policy SearchRules Rule 1 Authentication: No
*c xConfiguration Zones Policy SearchRules Rule 1 Mode: AliasPatternMatch
*c xConfiguration Zones Policy SearchRules Rule 1 Pattern Type: Regex
*c xConfiguration Zones Policy SearchRules Rule 1 Pattern String: "(.+)
@######.local.*"
*c xConfiguration Zones Policy SearchRules Rule 1 Pattern Behavior: Replace
*c xConfiguration Zones Policy SearchRules Rule 1 Pattern Replace: "\1"
*c xConfiguration Zones Policy SearchRules Rule 1 Progress: Continue
*c xConfiguration Zones Policy SearchRules Rule 1 Target Type: Zone
*c xConfiguration Zones Policy SearchRules Rule 1 Target Name: "LocalZone"
*c xConfiguration Zones Policy SearchRules Rule 1 State: Enabled
*c xConfiguration Zones Policy SearchRules Rule 2 Name: "Local zone ? full URI"
*c xConfiguration Zones Policy SearchRules Rule 2 Description: "Search local 
zone for SIP and H.323 devices with a domain"
*c xConfiguration Zones Policy SearchRules Rule 2 Priority: 51
*c xConfiguration Zones Policy SearchRules Rule 2 Protocol: Any
*c xConfiguration Zones Policy SearchRules Rule 2 Source Mode: Any
*c xConfiguration Zones Policy SearchRules Rule 2 Authentication: No
*c xConfiguration Zones Policy SearchRules Rule 2 Mode: AliasPatternMatch
*c xConfiguration Zones Policy SearchRules Rule 2 Pattern Type: Regex
*c xConfiguration Zones Policy SearchRules Rule 2 Pattern String: "(.+)
@######.local.*"
*c xConfiguration Zones Policy SearchRules Rule 2 Pattern Behavior: Leave
*c xConfiguration Zones Policy SearchRules Rule 2 Pattern Replace: ""
*c xConfiguration Zones Policy SearchRules Rule 2 Progress: Continue
*c xConfiguration Zones Policy SearchRules Rule 2 Target Type: Zone
*c xConfiguration Zones Policy SearchRules Rule 2 Target Name: "LocalZone"
*c xConfiguration Zones Policy SearchRules Rule 2 State: Enabled
*c xConfiguration Zones Policy SearchRules Rule 3 Name: "Traversal zone search rule"
*c xConfiguration Zones Policy SearchRules Rule 3 Description: "Search traversal 
zone (Cisco VCS Expressway)"
*c xConfiguration Zones Policy SearchRules Rule 3 Priority: 100
*c xConfiguration Zones Policy SearchRules Rule 3 Protocol: Any
*c xConfiguration Zones Policy SearchRules Rule 3 Source Mode: Any
*c xConfiguration Zones Policy SearchRules Rule 3 Authentication: No
*c xConfiguration Zones Policy SearchRules Rule 3 Mode: AnyAlias
*c xConfiguration Zones Policy SearchRules Rule 3 Progress: Continue
*c xConfiguration Zones Policy SearchRules Rule 3 Target Type: Zone
*c xConfiguration Zones Policy SearchRules Rule 3 Target Name: "TraversalZone"
*c xConfiguration Zones Policy SearchRules Rule 3 State: Enabled
*c xConfiguration Zones Policy SearchRules Rule 4 Name: "External IP address 
search rule"
*c xConfiguration Zones Policy SearchRules Rule 4 Description: "Route external 
IP address"
*c xConfiguration Zones Policy SearchRules Rule 4 Priority: 100
*c xConfiguration Zones Policy SearchRules Rule 4 Protocol: Any
*c xConfiguration Zones Policy SearchRules Rule 4 Source Mode: Any
*c xConfiguration Zones Policy SearchRules Rule 4 Authentication: No
*c xConfiguration Zones Policy SearchRules Rule 4 Mode: AnyIPAddress
*c xConfiguration Zones Policy SearchRules Rule 4 Progress: Continue
*c xConfiguration Zones Policy SearchRules Rule 4 Target Type: Zone
*c xConfiguration Zones Policy SearchRules Rule 4 Target Name: "TraversalZone"
*c xConfiguration Zones Policy SearchRules Rule 4 State: Enabled
*c xConfiguration Zones Policy SearchRules Rule 5 Name: "LocalZoneMatch"
*c xConfiguration Zones Policy SearchRules Rule 5 Description: "Default rule: 
queries the Local Zone for any alias"
*c xConfiguration Zones Policy SearchRules Rule 5 Priority: 50
*c xConfiguration Zones Policy SearchRules Rule 5 Protocol: Any
*c xConfiguration Zones Policy SearchRules Rule 5 Source Mode: Any
*c xConfiguration Zones Policy SearchRules Rule 5 Authentication: No
*c xConfiguration Zones Policy SearchRules Rule 5 Mode: AnyAlias
*c xConfiguration Zones Policy SearchRules Rule 5 Progress: Continue
*c xConfiguration Zones Policy SearchRules Rule 5 Target Type: Zone
*c xConfiguration Zones Policy SearchRules Rule 5 Target Name: "LocalZone"
*c xConfiguration Zones Policy SearchRules Rule 5 State: Enabled
*c xConfiguration Zones DefaultZone Authentication Mode: DoNotCheckCredentials
*c xConfiguration Zones DefaultZone SIP Record Route Address Type: IP
*c xConfiguration Zones DefaultZone SIP TLS Verify Mode: Off
*c xConfiguration Zones DefaultZone SIP Media Encryption Mode: Auto
*c xConfiguration Zones LocalZone DefaultSubZone SIP Media Encryption Mode: Auto
*c xConfiguration Zones LocalZone DefaultSubZone Authentication Mode: 
DoNotCheckCredentials
*c xConfiguration Zones LocalZone DefaultSubZone Registrations: Allow
*c xConfiguration Zones LocalZone DefaultSubZone Bandwidth Total Mode: Unlimited
*c xConfiguration Zones LocalZone DefaultSubZone Bandwidth PerCall Inter Mode:
Unlimited
*c xConfiguration Zones LocalZone DefaultSubZone Bandwidth PerCall Intra Mode:
Unlimited
*c xConfiguration Zones LocalZone TraversalSubZone Bandwidth Total Mode: Unlimited
*c xConfiguration Zones LocalZone TraversalSubZone Bandwidth PerCall Mode:
Unlimited
*c xConfiguration Zones LocalZone SIP Record Route Address Type: IP
*c xConfiguration Zones Zone 1 Name: "TraversalZone"
*c xConfiguration Zones Zone 1 HopCount: 15
*c xConfiguration Zones Zone 1 H323 Mode: On
*c xConfiguration Zones Zone 1 SIP Mode: On
*c xConfiguration Zones Zone 1 Type: TraversalClient
*c xConfiguration Zones Zone 1 TraversalClient Authentication Mode: DoNot
CheckCredentials
*c xConfiguration Zones Zone 1 TraversalClient Authentication UserName: 
"######auth"
*c xConfiguration Zones Zone 1 TraversalClient Authentication Password: 
"{cipher}XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX"
*c xConfiguration Zones Zone 1 TraversalClient Registrations: Allow
*c xConfiguration Zones Zone 1 TraversalClient H323 Protocol: Assent
*c xConfiguration Zones Zone 1 TraversalClient H323 Port: 6001
*c xConfiguration Zones Zone 1 TraversalClient SIP Protocol: Assent
*c xConfiguration Zones Zone 1 TraversalClient SIP Port: 7001
*c xConfiguration Zones Zone 1 TraversalClient SIP Transport: TLS
*c xConfiguration Zones Zone 1 TraversalClient SIP TLS Verify Mode: Off
*c xConfiguration Zones Zone 1 TraversalClient SIP Poison Mode: Off
*c xConfiguration Zones Zone 1 TraversalClient SIP Media Encryption Mode: Auto
*c xConfiguration Zones Zone 1 TraversalClient RetryInterval: 120
*c xConfiguration Zones Zone 1 TraversalClient Peer 1 Address: "10.10.10.102"
*c xConfiguration Zones Zone 1 TraversalClient Peer 2 Address: ""
*c xConfiguration Zones Zone 1 TraversalClient Peer 3 Address: ""
*c xConfiguration Zones Zone 1 TraversalClient Peer 4 Address: ""
*c xConfiguration Zones Zone 1 TraversalClient Peer 5 Address: ""
*c xConfiguration Zones Zone 1 TraversalClient Peer 6 Address: ""
*c xConfiguration Bandwidth Default: 384
*c xConfiguration Bandwidth Downspeed PerCall Mode: On
*c xConfiguration Bandwidth Downspeed Total Mode: On
*c xConfiguration Bandwidth Link 1 Name: "DefaultSZtoTraversalSZ"
*c xConfiguration Bandwidth Link 1 Node1 Name: "DefaultSubZone"
*c xConfiguration Bandwidth Link 1 Node2 Name: "TraversalSubZone"
*c xConfiguration Bandwidth Link 1 Pipe1 Name: ""
*c xConfiguration Bandwidth Link 1 Pipe2 Name: ""
*c xConfiguration Bandwidth Link 2 Name: "DefaultSZtoDefaultZ"
*c xConfiguration Bandwidth Link 2 Node1 Name: "DefaultSubZone"
*c xConfiguration Bandwidth Link 2 Node2 Name: "DefaultZone"
*c xConfiguration Bandwidth Link 2 Pipe1 Name: ""
*c xConfiguration Bandwidth Link 2 Pipe2 Name: ""
*c xConfiguration Bandwidth Link 3 Name: "DefaultSZtoClusterSZ"
*c xConfiguration Bandwidth Link 3 Node1 Name: "DefaultSubZone"
*c xConfiguration Bandwidth Link 3 Node2 Name: "ClusterSubZone"
*c xConfiguration Bandwidth Link 3 Pipe1 Name: ""
*c xConfiguration Bandwidth Link 3 Pipe2 Name: ""
*c xConfiguration Bandwidth Link 4 Name: "TraversalSZtoDefaultZ"
*c xConfiguration Bandwidth Link 4 Node1 Name: "TraversalSubZone"
*c xConfiguration Bandwidth Link 4 Node2 Name: "DefaultZone"
*c xConfiguration Bandwidth Link 4 Pipe1 Name: ""
*c xConfiguration Bandwidth Link 4 Pipe2 Name: ""
*c xConfiguration Bandwidth Link 5 Name: "Zone001ToTraversalSZ"
*c xConfiguration Bandwidth Link 5 Node1 Name: "TraversalZone"
*c xConfiguration Bandwidth Link 5 Node2 Name: "TraversalSubZone"
*c xConfiguration Bandwidth Link 5 Pipe1 Name: ""
*c xConfiguration Bandwidth Link 5 Pipe2 Name: ""
*c xConfiguration Policy AdministratorPolicy Mode: Off
*c xConfiguration Policy AdministratorPolicy Service Protocol: HTTP
*c xConfiguration Policy AdministratorPolicy Service TLS Verify Mode: On
*c xConfiguration Policy AdministratorPolicy Service TLS CRLCheck Mode: Off
*c xConfiguration Policy AdministratorPolicy Service Server 1 Address: ""
*c xConfiguration Policy AdministratorPolicy Service Server 2 Address: ""
*c xConfiguration Policy AdministratorPolicy Service Server 3 Address: ""
*c xConfiguration Policy AdministratorPolicy Service Path: ""
*c xConfiguration Policy AdministratorPolicy Service Status Path: "status"
*c xConfiguration Policy AdministratorPolicy Service UserName: ""
*c xConfiguration Policy AdministratorPolicy Service Password: "{cipher}
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX"
*c xConfiguration Policy AdministratorPolicy Service DefaultCPL: "<reject
 status='504' reason='Admin Policy Unavailable'/>"
*c xConfiguration Policy FindMe Mode: Off
*c xConfiguration Policy FindMe CallerId: IncomingID
*c xConfiguration Policy FindMe UserDeviceRestriction: Off
*c xConfiguration Applications ConferenceFactory Mode: Off
*c xConfiguration Applications ConferenceFactory Alias: ""
*c xConfiguration Applications ConferenceFactory Template: ""
*c xConfiguration Applications ConferenceFactory Range Start: 1
*c xConfiguration Applications ConferenceFactory Range End: 65535
*c xConfiguration Applications OCS Relay Mode: Off
*c xConfiguration Applications OCS Relay OCS Domain: ""
*c xConfiguration Applications OCS Relay OCS Routing Prefix: "ocs"
*c xConfiguration Applications Presence Server Mode: Off
*c xConfiguration Applications Presence Server Publication ExpireDelta: 1800
*c xConfiguration Applications Presence Server Subscription ExpireDelta: 3600
*c xConfiguration Applications Presence User Agent Mode: Off
*c xConfiguration Applications Presence User Agent ExpireDelta: 3600
*c xConfiguration Applications Presence User Agent RetryDelta: 1800
*c xConfiguration Applications Presence User Agent Presentity Idle Status: Online
*c xConfiguration ResourceUsage Warning Activation Level: 90
*c xConfiguration Services AdvancedMediaGateway Zone Name: ""
*c xConfiguration Services AdvancedMediaGateway Policy Mode: Off

OK
exit
Bye!

문제 해결

다음은 발생할 수 있는 가장 일반적인 세 가지 문제입니다.

잘못되었거나 결함이 있는 직렬 케이블이 사용됩니다. 디바이스와 함께 제공된 케이블을 사용해야 합니다.
인식할 수 없는 문자가 콘솔 화면에 표시됩니다. 이는 전송 속도가 잘못 설정되었음을 나타냅니다. 전송 속도는 2의 배수를 기준으로 하므로 올바른 설정을 찾을 때까지 필요에 따라 값을 두 배 또는 절반으로 줄일 수 있습니다. 이 경우 올바른 설정은 115,200이어야 합니다.
터미널 에뮬레이션 소프트웨어에 연결할 수 없습니다. 이 문제는 일반적으로 다음과 같은 문제 중 하나로 인해 발생합니다.
- 텔넷 또는 SSH를 통해 연결을 시도하며 직렬 연결을 사용할 때 연결 유형을 직렬 연결 유형으로 변경해야 합니다.
- 잘못된 COM 포트에 있습니다. PC에서 USB 기반 직렬 연결과 함께 사용하는 COM 포트를 검색하려면 Control Panel(제어판) > Device Manager(디바이스 관리자)로 이동하고 Ports(포트)를 클릭합니다. 이 창에서 USB 직렬 장치에 할당된 COM 포트를 확인할 수 있습니다.
- 직렬 장치용 드라이버가 설치되어 있지 않습니다. 이 경우 찾아 설치해야 합니다.
디바이스에 SSH를 연결할 수 없습니다. 이 문제는 일반적으로 다음과 같은 문제 중 하나로 인해 발생합니다.
- SSH를 통해 연결을 시도했지만 네트워크 연결 문제로 인해 디바이스에 연결할 수 없습니다. 네트워크 연결 문제를 수정하십시오. 또는 디바이스에 대해 SSH가 활성화되지 않을 수 있습니다. 디바이스에 웹/HTTP/HTTPS를 연결하고 Configuration(컨피그레이션)>System(시스템)Configuration(컨피그레이션)>Network Services(네트워크 서비스)에서 SSH 액세스가 활성화되었는지 확인합니다.
- 디바이스에서 캐시된 Rivest-Shamir-Addleman(RSA) 키가 없습니다. 일반적으로 RSA 키를 승인하라는 메시지가 표시됩니다. 반드시 키를 수락하십시오.
- 사용자 이름과 암호가 잘못되어 로그인이 실패합니다. 디바이스에 올바른 사용자 이름과 비밀번호를 사용해야 합니다.

개정 이력

개정	게시 날짜	의견
1.0	15-Dec-2014	최초 릴리스

Cisco 엔지니어가 작성

Michael Jason Wall and Adam Wamsley
Cisco TAC Engineers.

이 문서가 도움이 되셨습니까?

피드백

지원 문의

지원 케이스 접수
(시스코 서비스 계약 필요)