Cisco 7500 라우터 및 LightStream 1010 스위치로 ATM을 통한 VPN MPLS 구성

다운로드 옵션

  • PDF     (323.7 KB)
    다양한 디바이스에서 Adobe Reader로 보기
  • ePub     (113.3 KB)
    iPhone, iPad, Android, Sony Reader 또는 Windows Phone의 다양한 앱에서 보기
  • Mobi (Kindle)     (131.9 KB)
    Kindle 디바이스에서 보기 또는 다양한 디바이스의 Kindle 앱에서 보기
업데이트:2005년 6월 5일
문서 ID:10533

편견 없는 언어

본 제품에 대한 문서 세트는 편견 없는 언어를 사용하기 위해 노력합니다. 본 설명서 세트의 목적상, 편견 없는 언어는 나이, 장애, 성별, 인종 정체성, 민족 정체성, 성적 지향성, 사회 경제적 지위 및 교차성에 기초한 차별을 의미하지 않는 언어로 정의됩니다. 제품 소프트웨어의 사용자 인터페이스에서 하드코딩된 언어, RFP 설명서에 기초한 언어 또는 참조된 서드파티 제품에서 사용하는 언어로 인해 설명서에 예외가 있을 수 있습니다. 시스코에서 어떤 방식으로 포용적인 언어를 사용하고 있는지 자세히 알아보세요.

이 번역에 관하여

Cisco는 전 세계 사용자에게 다양한 언어로 지원 콘텐츠를 제공하기 위해 기계 번역 기술과 수작업 번역을 병행하여 이 문서를 번역했습니다. 아무리 품질이 높은 기계 번역이라도 전문 번역가의 번역 결과물만큼 정확하지는 않습니다. Cisco Systems, Inc.는 이 같은 번역에 대해 어떠한 책임도 지지 않으며 항상 원본 영문 문서(링크 제공됨)를 참조할 것을 권장합니다.

소개

이 문서에서는 Cisco 7500 라우터를 LER(Label Edge Router)로, LightStream 1010 스위치를 LSR(Label Switch Router)로 사용하여 ATM을 통해 VPN(Virtual Private Network) MPLS(Multiprotocol Label Switching)를 구성하는 방법을 보여 줍니다. 각각 원격 고객 사이트에 있는 2개의 이더넷 연결 라우터는 VPN에 속합니다. 이 문서에서는 엔드 투 엔드 디바이스 컨피그레이션과 유용한 show 명령을 살펴봅니다.

사전 요구 사항

요구 사항

이 문서에 대한 특정 요건이 없습니다.

표기 규칙

문서 규칙에 대한 자세한 내용은 Cisco 기술 팁 표기 규칙을 참고하십시오.

구성

이 섹션에는 이 문서에서 설명하는 기능을 구성하기 위한 정보가 표시됩니다.

네트워크 다이어그램

이 문서에서는 이 네트워크 설정을 사용합니다.

vpn-mpls-1.gif

네트워크 설명

현재 설정에는 VPN 용어에 다음 요소가 포함되어 있습니다.

  • CE = Customer Edge 라우터

  • PE = 공급자 에지 라우터

  • P=사업자 라우터

현재 설정에는 MPLS 용어에 다음 요소가 포함되어 있습니다.

  • LER = Label Edge 라우터

  • LSR = 라벨 스위치 라우터

  • TDP/LDP = Tag Distribution Protocol/Label Distribution Protocol

설정

이 문서에서는 다음 설정을 사용합니다.

  • PE1과 PE2는 ATM 네트워크의 LER입니다.

  • P1 및 P2는 LSR입니다.

  • CE1 및 CE2는 VPN 또는 MPLS를 인식하지 못하고 수행하지 않는 고객 에지 라우터입니다.

  • CE1과 CE2는 각각 PE1과 PE2에 연결된 이더넷으로 RIP(Routing Information Protocol)를 수행합니다.

  • PE1, PE2, P1 및 P2는 모두 OSPF(Open Shortest Path First)를 사용하며 영역 0에 있습니다. OSPF는 ATM 네트워크에서 사용되는 IGP(Interior Gateway Protocol)입니다. 태그 스위칭은 4개의 모든 ATM 디바이스의 ATM 인터페이스에서 사용됩니다. TDP(Tag Distribution Protocol)는 OSPF 경로에 태그를 할당합니다.

  • PE1 및 PE2는 MP-BGP(Multiprotocol-Border Gateway Protocol) 피어입니다.

  • RIP 경로가 MP-BGP로 재배포됩니다. PE1 및 PE2 라우터의 RIP에 재배포된 MP-BGP 경로.

  • 이 설정은 PE1 및 PE2 라우터에 별도의 VRF 라우팅 테이블을 유지합니다.

  • 이 예에서 사용하는 VPN의 이름은 NEW입니다.

CE1 
! 
version 12.1 
service timestamps debug datetime msec 
service timestamps log datetime msec 

! 
boot system flashow c4500-js-mz.121-5 
! 

ip subnet-zero 

! 
interface Loopback0 
 ip address 10.1.1.1 255.255.255.0 
! 
interface Loopback1 
 ip address 10.2.2.2 255.255.255.0 
! 
interface Loopback2 
 ip address 10.3.3.3 255.255.255.0 
! 
interface Ethernet0 
 ip address 100.1.1.2 255.255.255.0 
 media-type 10BaseT 

! 

router rip 
 version 2 
 network 10.0.0.0 
 network 100.0.0.0 
 no auto-summary 
! 
ip classless 
!

PE1 
! 
version 12.1 

service timestamps debug uptime 
service timestamps log uptime 

! 
boot system flashow slot1:rsp-jsv-mz.121-5a.bin 
! 

ip subnet-zero 

! 
ip vrf NEW 
 rd 200:1 
 route-target export 200:1 
 route-target import 200:1 
ip cef distributed 

! 
interface Loopback0 
 ip address 1.1.1.1 255.255.255.255 
! 
interface ATM2/0/0 
 mtu 1500 
 no ip address 
! 
interface ATM2/0/0.10 tag-switching 
 ip unnumbered Loopback0 
 tag-switching ip 
! 
interface Ethernet2/1/0 
 ip vrf forwarding NEW 
 ip address 100.1.1.1 255.255.255.0 

! 
router ospf 100 
 no log-adjacency-changes 
 network 1.0.0.0 0.255.255.255 area 0 
 network 100.1.1.0 0.0.0.255 area 0 
! 
router rip 
 version 2 
 network 100.0.0.0 
 no auto-summary 
 ! 
 address-family ipv4 vrf NEW 
 version 2 
 redistribute bgp 200 metric 0 
 network 100.0.0.0 
 no auto-summary 
 exit-address-family 
! 
router bgp 200 
 bgp log-neighbor-changes 
 neighbor 2.2.2.2 remote-as 200 

 neighbor 2.2.2.2 update-source Loopback0 
 no auto-summary 
 ! 
 address-family ipv4 vrf NEW 
 redistribute rip 
 no auto-summary 
 no synchronization 
 exit-address-family 
 ! 
 address-family vpnv4 
 neighbor 2.2.2.2 activate 
 neighbor 2.2.2.2 send-community extended 
 no auto-summary 
 exit-address-family 
! 
ip classless 
!

P1 
!

service timestamps debug uptime 
service timestamps log uptime 
!

ip subnet-zero 
! 

interface Loopback0 
 ip address 4.4.4.4 255.255.255.255 
 no ip directed-broadcast 
! 
interface ATM12/0/0 
 ip unnumbered Loopback0 
 no ip directed-broadcast 

 tag-switching ip 
! 
interface ATM12/0/1 
 ip unnumbered Loopback0 
 no ip directed-broadcast 

 tag-switching ip 

! 
router ospf 100 
 network 4.0.0.0 0.255.255.255 area 0 
! 
ip classless 
!

P2 
! 
service timestamps debug uptime 
service timestamps log uptime 

! 
ip subnet-zero 

! 
interface Loopback0 
 ip address 3.3.3.3 255.255.255.255 
 no ip directed-broadcast 
!  
interface ATM0/1/1 
 ip unnumbered Loopback0 
 no ip directed-broadcast 

 tag-switching ip 
! 
interface ATM0/1/3 
 ip unnumbered Loopback0 
 no ip directed-broadcast 

 tag-switching ip 

! 
router ospf 100 
 network 3.0.0.0 0.255.255.255 area 0 
! 
ip classless 
!

PE2 
! 
version 12.1 
service timestamps debug datetime msec 
service timestamps log datetime msec 

! 
boot system flashow slot0:rsp-jsv-mz.121-5a 
! 

ip subnet-zero 

! 
ip vrf NEW 
 rd 200:1 
 route-target export 200:1 
 route-target import 200:1 
ip cef distributed 

! 
interface Loopback0 
 ip address 2.2.2.2 255.255.255.255 
! 

interface FastEthernet3/0/0 
 ip vrf forwarding NEW 
 ip address 110.1.1.1 255.255.255.0 

 half-duplex 
! 

interface ATM3/1/0.1 tag-switching 
 ip unnumbered Loopback0 
 tag-switching ip 
! 
router ospf 100 
 log-adjacency-changes 
 network 2.0.0.0 0.255.255.255 area 0 

! 
router rip 
 version 2 
 network 110.0.0.0 
 no auto-summary 
 ! 
 address-family ipv4 vrf NEW 
 version 2 
 redistribute bgp 200 metric 0 
 network 110.0.0.0 
 no auto-summary 
 exit-address-family 
! 
router bgp 200 
 bgp log-neighbor-changes 
 neighbor 1.1.1.1 remote-as 200 

 neighbor 1.1.1.1 update-source Loopback0 

 no auto-summary 
 ! 
 address-family ipv4 vrf NEW 
 redistribute rip 
 no auto-summary 
 no synchronization 
 exit-address-family 
 ! 
 address-family vpnv4 
 neighbor 1.1.1.1 activate 
 neighbor 1.1.1.1 send-community extended
 no auto-summary 
 exit-address-family 
! 
ip classless 
!

CE2 
! 
version 12.1 

service timestamps debug uptime 
service timestamps log uptime 

! 

boot system disk0:c7100-jo3s56i-mz.121-5.T.bin 

! 
ip subnet-zero 

! 
interface Loopback0 
 ip address 30.1.1.1 255.255.255.0 
! 
interface Loopback1 
 ip address 30.2.2.2 255.255.255.0 
! 
interface Loopback2 
 ip address 30.3.3.3 255.255.255.0 
! 
interface FastEthernet0/0 
 ip address 110.1.1.2 255.255.255.0 

! 
router rip 
 version 2 
 network 30.0.0.0 
 network 110.0.0.0 
 no auto-summary 
!

show 명령

다음 명령을 사용하여 네트워크가 제대로 작동하는지 테스트합니다.

  • show ip route - IP 라우팅 테이블 항목을 표시합니다.

  • show ip rip database vrf - 특정 VRF에 대한 RIP 데이터베이스에 포함된 정보를 표시합니다.

  • show ip bgp vpnv4 vrf - BGP 테이블의 VPN 주소 정보를 표시합니다.

  • show tag-switching interfaces detail - MPLS 기능이 활성화된 하나 이상의 인터페이스에 대한 정보를 표시합니다.

  • show tag-switching tdp bindings - ATM LDP 레이블 바인딩 데이터베이스에서 요청한 항목을 표시합니다.

  • show tag-switching forwarding-table vrf - 특정 경로에 사용된 레이블 스택을 확인합니다.

아래에 표시된 출력은 네트워크 다이어그램에 표시된 디바이스에서 입력한 명령의 결과입니다. 이 출력은 네트워크가 제대로 작동함을 보여줍니다.

CE1 

Cisco4500#show ip route 
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP 
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP 
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area 
       * - candidate default, U - per-user static route, o - ODR 
       P - periodic downloaded static route 

Gateway of last resort is not set 

     100.0.0.0/24 is subnetted, 1 subnets 
C       100.1.1.0 is directly connected, Ethernet0 
     110.0.0.0/24 is subnetted, 1 subnets 
R       110.1.1.0 [120/1] via 100.1.1.1, 00:00:14, Ethernet0 
     10.0.0.0/24 is subnetted, 3 subnets 
C       10.3.3.0 is directly connected, Loopback2 
C       10.2.2.0 is directly connected, Loopback1 
C       10.1.1.0 is directly connected, Loopback0 
     30.0.0.0/24 is subnetted, 3 subnets 
R       30.3.3.0 [120/1] via 100.1.1.1, 00:00:14, Ethernet0 
R       30.2.2.0 [120/1] via 100.1.1.1, 00:00:15, Ethernet0 
R       30.1.1.0 [120/1] via 100.1.1.1, 00:00:15, Ethernet0

PE1 

Cisco7500a#show ip route 
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP 
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP 
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area 
       * - candidate default, U - per-user static route, o - ODR 
       P - periodic downloaded static route 

Gateway of last resort is not set 

     1.0.0.0/32 is subnetted, 1 subnets 
C       1.1.1.1 is directly connected, Loopback0 
     2.0.0.0/32 is subnetted, 1 subnets 
O       2.2.2.2 [110/4] via 4.4.4.4, 18:17:37, ATM2/0/0.10 
     3.0.0.0/32 is subnetted, 1 subnets 
O       3.3.3.3 [110/3] via 4.4.4.4, 18:17:37, ATM2/0/0.10 
     4.0.0.0/32 is subnetted, 1 subnets 
O       4.4.4.4 [110/2] via 4.4.4.4, 18:17:37, ATM2/0/0.10 

Cisco7500a#show ip route vrf NEW 
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP 
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP 
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area 
       * - candidate default, U - per-user static route, o - ODR 
       P - periodic downloaded static route 

Gateway of last resort is not set 

     100.0.0.0/24 is subnetted, 1 subnets 
C       100.1.1.0 is directly connected, Ethernet2/1/0 
     110.0.0.0/24 is subnetted, 1 subnets 
B       110.1.1.0 [200/0] via 2.2.2.2, 00:26:11 
     10.0.0.0/24 is subnetted, 3 subnets 
R       10.3.3.0 [120/1] via 100.1.1.2, 00:00:11, Ethernet2/1/0 
R       10.2.2.0 [120/1] via 100.1.1.2, 00:00:11, Ethernet2/1/0 
R       10.1.1.0 [120/1] via 100.1.1.2, 00:00:11, Ethernet2/1/0 
     30.0.0.0/24 is subnetted, 3 subnets 
B       30.3.3.0 [200/1] via 2.2.2.2, 00:26:12 
B       30.2.2.0 [200/1] via 2.2.2.2, 00:26:12 
B       30.1.1.0 [200/1] via 2.2.2.2, 00:26:12

Cisco7500a#show ip rip database vrf NEW 
10.0.0.0/8    auto-summary 
10.1.1.0/24 
    [1] via 100.1.1.2, 00:00:18, Ethernet2/1/0 
10.2.2.0/24 
    [1] via 100.1.1.2, 00:00:18, Ethernet2/1/0 
10.3.3.0/24 
    [1] via 100.1.1.2, 00:00:18, Ethernet2/1/0 
30.0.0.0/8    auto-summary 
30.1.1.0/24    redistributed 
    [1] via 2.2.2.2, 
30.2.2.0/24    redistributed 
    [1] via 2.2.2.2, 
30.3.3.0/24    redistributed 
    [1] via 2.2.2.2, 
100.0.0.0/8    auto-summary 
100.1.1.0/24    directly connected, Ethernet2/1/0 
110.0.0.0/8    auto-summary 
110.1.1.0/24    redistributed 
    [1] via 2.2.2.2, 

Cisco7500a#show ip bgp vpnv4 vrf NEW 
BGP table version is 17, local router ID is 1.1.1.1 
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal 
Origin codes: i - IGP, e - EGP, ? - incomplete 

   Network          Next Hop            Metric LocPrf Weight Path 
Route Distinguisher: 200:1 (default for vrf NEW) 
*> 10.1.1.0/24      100.1.1.2                1         32768 ? 
*> 10.2.2.0/24      100.1.1.2                1         32768 ? 
*> 10.3.3.0/24      100.1.1.2                1         32768 ? 
*>i30.1.1.0/24      2.2.2.2                  1    100      0 ? 
*>i30.2.2.0/24      2.2.2.2                  1    100      0 ? 
*>i30.3.3.0/24      2.2.2.2                  1    100      0 ? 
*> 100.1.1.0/24     0.0.0.0                  0         32768 ? 
*>i110.1.1.0/24     2.2.2.2                  0    100      0 ? 

Cisco7500a#show tag-switching interfaces 
Interface              IP    Tunnel   Operational 
ATM2/0/0.10            Yes   No       Yes         (ATM tagging) 

Cisco7500a#show tag-switching interfaces detail 
Interface ATM2/0/0.10: 
        IP tagging enabled 
        TSP Tunnel tagging not enabled 
        Tagging operational 
        Tagswitching turbo vector 
        MTU = 4470 
        ATM tagging: 
                Tag VPI = 1 
                Tag VCI range = 33 - 65535 
                Control VC = 0/32 

Cisco7500a#show tag-switching ? 
  atm-tdp           ATM Tagging Protocol information 
  cos-map           Show Tag CoS ATM Multi-VC CoS Map 
  forwarding-table  Show the Tag Forwarding Information Base (TFIB) 
  interfaces        Show per-interface tag switching 
  prefix-map        Show Tag CoS Prefix Map 
  tdp               Tag Distribution Protocol information 
  
Cisco7500a#show tag-switching tdp bindings 
  tib entry: 1.1.1.1/32, rev 2 
        local binding:  tag: imp-null 
  tib entry: 2.2.2.2/32, rev 23 
        local binding:  tag: 27 
  tib entry: 3.3.3.3/32, rev 21 
        local binding:  tag: 26 
  tib entry: 4.4.4.4/32, rev 10 
        local binding:  tag: 28 

Cisco7500a#show tag-switching atm-tdp bindings 
 Destination: 4.4.4.4/32 
    Headend Router ATM2/0/0.10 (1 hop) 1/33  Active, VCD=24 
 Destination: 3.3.3.3/32 
    Headend Router ATM2/0/0.10 (2 hops) 1/43  Active, VCD=25 
 Destination: 2.2.2.2/32 
    Headend Router ATM2/0/0.10 (3 hops) 1/42  Active, VCD=26 
 Destination: 1.1.1.1/32 
    Tailend Router ATM2/0/0.10 1/33 Active, VCD=24 

Cisco7500a#show tag-switching forwarding-table vrf NEW 
Local  Outgoing    Prefix            Bytes tag  Outgoing   Next Hop 
tag    tag or VC   or Tunnel Id      switched   interface 
29     Aggregate   100.1.1.0/24[V]   2080 
30     Untagged    10.3.3.0/24[V]    0          Et2/1/0    100.1.1.2 
31     Untagged    10.2.2.0/24[V]    0          Et2/1/0    100.1.1.2 
32     Untagged    10.1.1.0/24[V]    0          Et2/1/0    100.1.1.2

P1 

LS1010#show ip route 
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP 
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP 
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default 
       U - per-user static route, o - ODR 
       T - traffic engineered route 

Gateway of last resort is not set 

     1.0.0.0/32 is subnetted, 1 subnets 
O       1.1.1.1 [110/2] via 1.1.1.1, 19:00:12, ATM12/0/0 
     2.0.0.0/32 is subnetted, 1 subnets 
O       2.2.2.2 [110/3] via 3.3.3.3, 19:00:12, ATM12/0/1 
     3.0.0.0/32 is subnetted, 1 subnets 
O       3.3.3.3 [110/2] via 3.3.3.3, 19:00:12, ATM12/0/1 
     4.0.0.0/32 is subnetted, 1 subnets 
C       4.4.4.4 is directly connected, Loopback0 

LS1010#show tag-switching atm-tdp bindings 
 Destination: 4.4.4.4/32 
    Tailend Switch ATM12/0/0 1/33 Active -> Terminating Active 
    Tailend Switch ATM12/0/1 1/34 Active -> Terminating Active 
 Destination: 2.2.2.2/32 
    Transit ATM12/0/0 1/42 Active -> ATM12/0/1 1/35 Active 
 Destination: 1.1.1.1/32 
    Transit ATM12/0/1 1/33 Active -> ATM12/0/0 1/33 Active 
 Destination: 3.3.3.3/32 
    Transit ATM12/0/0 1/43 Active -> ATM12/0/1 1/34 Active

P2 

LS1010#show ip route 
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP 
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP 
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default 
       U - per-user static route, o - ODR 

Gateway of last resort is 10.118.1.21 to network 0.0.0.0 

     1.0.0.0/32 is subnetted, 1 subnets 
O       1.1.1.1 [110/3] via 4.4.4.4, 19:46:00, ATM0/1/1 
     2.0.0.0/32 is subnetted, 1 subnets 
O       2.2.2.2 [110/2] via 2.2.2.2, 19:46:00, ATM0/1/3 
     3.0.0.0/32 is subnetted, 1 subnets 
C       3.3.3.3 is directly connected, Loopback0 
     4.0.0.0/32 is subnetted, 1 subnets 
O       4.4.4.4 [110/2] via 4.4.4.4, 19:46:00, ATM0/1/1 
     10.0.0.0/24 is subnetted, 1 subnets 
C       10.118.1.0 is directly connected, Ethernet2/0/0 
S*   0.0.0.0/0 [1/0] via 10.118.1.21

LS1010#show tag-switching atm-tdp bindings 
 Destination: 1.1.1.1/32 
    Transit ATM0/1/3 1/33 Active -> ATM0/1/1 1/33 Active 
 Destination: 3.3.3.3/32 
    Tailend Switch ATM0/1/3 1/34 Active -> Terminating Active 
    Tailend Switch ATM0/1/1 1/34 Active -> Terminating Active 
 Destination: 4.4.4.4/32 
    Transit ATM0/1/3 1/35 Active -> ATM0/1/1 1/34 Active 
 Destination: 2.2.2.2/32 
    Transit ATM0/1/1 1/35 Active -> ATM0/1/3 1/33 Active

PE2 

Cisco7500#show ip route 
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP 
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP 
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area 
       * - candidate default, U - per-user static route, o - ODR 
       P - periodic downloaded static route 

Gateway of last resort is not set 

     1.0.0.0/32 is subnetted, 1 subnets 
O       1.1.1.1 [110/4] via 3.3.3.3, 02:58:46, ATM3/1/0.1 
     2.0.0.0/32 is subnetted, 1 subnets 
C       2.2.2.2 is directly connected, Loopback0 
     3.0.0.0/32 is subnetted, 1 subnets 
O       3.3.3.3 [110/2] via 3.3.3.3, 02:58:46, ATM3/1/0.1 
     4.0.0.0/32 is subnetted, 1 subnets 
O       4.4.4.4 [110/3] via 3.3.3.3, 02:58:46, ATM3/1/0.1 

Cisco7500#show ip route vrf NEW 
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP 
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP 
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area 
       * - candidate default, U - per-user static route, o - ODR 
       P - periodic downloaded static route 

Gateway of last resort is not set 

     100.0.0.0/24 is subnetted, 1 subnets 
B       100.1.1.0 [200/0] via 1.1.1.1, 01:16:13 
     110.0.0.0/24 is subnetted, 1 subnets 
C       110.1.1.0 is directly connected, FastEthernet3/0/0 
     10.0.0.0/24 is subnetted, 3 subnets 
B       10.3.3.0 [200/1] via 1.1.1.1, 01:16:13 
B       10.2.2.0 [200/1] via 1.1.1.1, 01:16:13 
B       10.1.1.0 [200/1] via 1.1.1.1, 01:16:13 
     30.0.0.0/24 is subnetted, 3 subnets 
R       30.3.3.0 [120/1] via 110.1.1.2, 00:00:16, FastEthernet3/0/0 
R       30.2.2.0 [120/1] via 110.1.1.2, 00:00:17, FastEthernet3/0/0 
R       30.1.1.0 [120/1] via 110.1.1.2, 00:00:17, FastEthernet3/0/0 

Cisco7500#show ip rip database vrf NEW 
10.0.0.0/8    auto-summary 
10.1.1.0/24    redistributed 
    [1] via 1.1.1.1, 
10.2.2.0/24    redistributed 
    [1] via 1.1.1.1, 
10.3.3.0/24    redistributed 
    [1] via 1.1.1.1, 
30.0.0.0/8    auto-summary 
30.1.1.0/24 
    [1] via 110.1.1.2, 00:00:09, FastEthernet3/0/0 
30.2.2.0/24 
    [1] via 110.1.1.2, 00:00:09, FastEthernet3/0/0 
30.3.3.0/24 
    [1] via 110.1.1.2, 00:00:09, FastEthernet3/0/0 
100.0.0.0/8    auto-summary 
100.1.1.0/24    redistributed 
    [1] via 1.1.1.1, 
110.0.0.0/8    auto-summary 
110.1.1.0/24    directly connected, FastEthernet3/0/0 
Cisco7500#show ip bgp vpnv4 vrf NEW 
BGP table version is 17, local router ID is 2.2.2.2 
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal 
Origin codes: i - IGP, e - EGP, ? - incomplete 

   Network          Next Hop            Metric LocPrf Weight Path 
Route Distinguisher: 200:1 (default for vrf NEW) 
*>i10.1.1.0/24      1.1.1.1                  1    100      0 ? 
*>i10.2.2.0/24      1.1.1.1                  1    100      0 ? 
*>i10.3.3.0/24      1.1.1.1                  1    100      0 ? 
*> 30.1.1.0/24      110.1.1.2                1         32768 ? 
*> 30.2.2.0/24      110.1.1.2                1         32768 ? 
*> 30.3.3.0/24      110.1.1.2                1         32768 ? 
*>i100.1.1.0/24     1.1.1.1                  0    100      0 ? 
*> 110.1.1.0/24     0.0.0.0                  0         32768 ? 

Cisco7500#show tag-switching interfaces 
Interface              IP    Tunnel   Operational 
ATM3/1/0.1             Yes   No       Yes         (ATM tagging) 

Cisco7500#show tag-switching interfaces detail 
Interface ATM3/1/0.1: 
        IP tagging enabled 
        TSP Tunnel tagging not enabled 
        Tagging operational 
        Tagswitching turbo vector 
        MTU = 4470 
        ATM tagging: 
                Tag VPI = 1 
                Tag VCI range = 33 - 65535 
                Control VC = 0/32 

Cisco7500#show tag-switching ? 
  atm-tdp           ATM Tagging Protocol information 
  cos-map           Show Tag CoS ATM Multi-VC CoS Map 
  forwarding-table  Show the Tag Forwarding Information Base (TFIB) 
  interfaces        Show per-interface tag switching 
  prefix-map        Show Tag CoS Prefix Map 
  tdp               Tag Distribution Protocol information

Cisco7500#show tag-switching tdp bindings 
  tib entry: 1.1.1.1/32, rev 25 
        local binding:  tag: 26 
  tib entry: 2.2.2.2/32, rev 2 
        local binding:  tag: imp-null 
  tib entry: 3.3.3.3/32, rev 27 
        local binding:  tag: 27 
  tib entry: 4.4.4.4/32, rev 29 
        local binding:  tag: 28 

Cisco7500#show tag-switching atm-tdp bindings 
 Destination: 1.1.1.1/32 
    Headend Router ATM3/1/0.1 (3 hops) 1/33  Active, VCD=8 
 Destination: 3.3.3.3/32 
    Headend Router ATM3/1/0.1 (1 hop) 1/34  Active, VCD=6 
 Destination: 4.4.4.4/32 
    Headend Router ATM3/1/0.1 (2 hops) 1/35  Active, VCD=7 
 Destination: 2.2.2.2/32 
    Tailend Router ATM3/1/0.1 1/33 Active, VCD=8 

Cisco7500#show tag-switching forwarding-table vrf NEW 
Local  Outgoing    Prefix            Bytes tag  Outgoing   Next Hop 
tag    tag or VC   or Tunnel Id      switched   interface 
33     Aggregate   110.1.1.0/24[V]   0 
34     Untagged    30.3.3.0/24[V]    0          Fa3/0/0    110.1.1.2 
35     Untagged    30.2.2.0/24[V]    0          Fa3/0/0    110.1.1.2 
36     Untagged    30.1.1.0/24[V]    0          Fa3/0/0    110.1.1.2

CE2 

Cisco7100#show ip route 
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP 
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP 
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area 
       * - candidate default, U - per-user static route, o - ODR 
       P - periodic downloaded static route 

Gateway of last resort is not set 

     100.0.0.0/24 is subnetted, 1 subnets 
R       100.1.1.0 [120/1] via 110.1.1.1, 00:00:19, FastEthernet0/0 
     110.0.0.0/24 is subnetted, 1 subnets 
C       110.1.1.0 is directly connected, FastEthernet0/0 
     10.0.0.0/24 is subnetted, 3 subnets 
R       10.3.3.0 [120/1] via 110.1.1.1, 00:00:19, FastEthernet0/0 
R       10.2.2.0 [120/1] via 110.1.1.1, 00:00:19, FastEthernet0/0 
R       10.1.1.0 [120/1] via 110.1.1.1, 00:00:19, FastEthernet0/0 
     30.0.0.0/24 is subnetted, 3 subnets 
C       30.3.3.0 is directly connected, Loopback2 
C       30.2.2.0 is directly connected, Loopback1 
C       30.1.1.0 is directly connected, Loopback0

관련 정보

개정 이력

개정 게시 날짜 의견
1.0
29-Nov-2001
최초 릴리스

이 문서가 도움이 되셨습니까?

Feedback피드백

지원 문의

이 문서가 적용되는 제품