이 문서에서는 Cisco Catalyst 5500과 Catalyst 3500XL 스위치 간의 ISL(InterSwitch Link Protocol) 및 IEEE 802.1Q 트렁킹을 위한 샘플 구성을 제공합니다. 이 문서에는 명령을 실행할 때 각 명령의 결과가 표시됩니다. 이 문서의 시나리오에서 이러한 스위치를 사용하여 동일한 결과를 얻을 수 있습니다.
Catalyst OS(CatOS)를 실행하는 Catalyst 4500/4000 및 6500/6000 Series 스위치
Catalyst 5500/5000 시리즈의 다른 멤버
모든 Catalyst Layer 2 고정 구성 스위치
Catalyst Layer 2 고정 구성 스위치에는 2900/3500XL, 2940, 2950/2955 및 2970이 포함됩니다.
이 문서를 계속 진행하기 전에 VLAN 트렁킹 프로토콜 지원을 참조하십시오.
이 문서에 대한 특정 요건이 없습니다.
이 문서의 예제를 작성하기 위해 이 스위치는 랩 환경에서 컨피그레이션이 지워진 상태로 사용되었습니다.
Cisco IOS® 소프트웨어 릴리스 12.0(5)WC7을 실행하는 Catalyst 3524XL 스위치
CatOS 6.4(2) 소프트웨어를 실행하는 Catalyst 5500 스위치
이 문서의 컨피그레이션은 격리된 랩 환경에서 구현되었습니다. 모든 컨피그레이션 또는 명령이 네트워크에 미칠 수 있는 잠재적인 영향을 파악해야 합니다. 모든 디바이스의 컨피그레이션은 Catalyst 5500 스위치의 clear config all 명령 및 Catalyst 3524XL 스위치의 write erase 명령으로 초기화되어 기본 컨피그레이션을 보장합니다.
문서 규칙에 대한 자세한 내용은 Cisco 기술 팁 표기 규칙을 참조하십시오.
트렁킹은 두 디바이스 간의 포인트 투 포인트 링크를 통해 여러 VLAN의 트래픽을 전달하는 방법입니다. 이더넷 트렁킹을 구현할 수 있는 두 가지 방법은 다음과 같습니다.
ISL, Cisco 독점 프로토콜
IEEE 802.1Q 표준
이 문서에서는 Catalyst 3500과 Catalyst 5500 스위치 간의 단일 링크를 통해 두 VLAN의 트래픽을 전달하는 트렁크를 생성합니다. 두 VLAN 간의 라우팅 방법에 대한 정보는 이 문서의 범위를 벗어납니다.
Catalyst 2940/2950/2955/2970 스위치의 경우
Catalyst 2940 및 2950/2955 Series 스위치는 802.1Q 트렁킹만 지원합니다. 이 스위치는 ISL 트렁킹을 지원하지 않습니다.
Catalyst 2970 Series 스위치는 ISL과 802.1Q 트렁킹을 모두 지원합니다.
Catalyst 2900XL/3500XL 스위치
Catalyst 2900XL/3500XL 스위치는 DTP(Dynamic Trunking Protocol)를 지원하지 않습니다. 트렁크 링크의 반대쪽에 있는 switchport trunk 명령에 대해 nonegotiate 옵션을 사용합니다. nonegotiate 옵션을 사용하면 XL 스위치에서 처리할 수 없는 피어에서 DTP 프레임을 수신하지 못하게 됩니다.
참고: 4MB DRAM Catalyst 2900XL 스위치에서는 다음과 같은 트렁킹 가능 모듈만 트렁킹 지원됩니다.
WS-X2914-XL-V
WS-X2922-XL-V
WS-X2924-XL-V
WS-X2931-XL
WS-X2932-XL
트렁킹을 지원하는 스위치 모델의 현재 목록은 다음 표를 참조하십시오.
스위치 모델 | ISL 트렁킹에 필요한 최소 Cisco IOS 소프트웨어 릴리스 | 802.1Q 트렁킹에 필요한 최소 Cisco IOS 소프트웨어 릴리스 | 트렁킹에 필요한 현재 Cisco IOS 소프트웨어 릴리스(ISL/802.1Q ) |
---|---|---|---|
WS-C2916M-XL(4MB 스위치) | Cisco IOS Software 릴리스 11.2(8)SA4, Enterprise Edition | Cisco IOS Software 릴리스 11.2(8)SA5, Original Edition | Cisco IOS Software 릴리스 11.2(8.6)SA6, Original Edition |
WS-C2912-XL WS-C2924-XL WS-C2924C-XL WS-C2924M-XL WS-C2912MF-XL | Cisco IOS Software 릴리스 11.2(8)SA4, Enterprise Edition | Cisco IOS Software 릴리스 11.2(8)SA5, Original Edition | Cisco IOS Software 릴리스 12.0(5)WC(1) 이상 |
WS-C2924M-XL-DC | Cisco IOS Software 릴리스 12.0(5)XU | Cisco IOS Software 릴리스 12.0(5)XU | Cisco IOS Software 릴리스 12.0(5)WC(1) 이상 |
WS-C3508G-XL WS-C3512-XL WS-C3524-XL | Cisco IOS Software 릴리스 11.2(8)SA4, Enterprise Edition | Cisco IOS Software 릴리스 11.2(8)SA5, Original Edition | Cisco IOS Software 릴리스 12.0(5)WC(1) 이상 |
WS-C3548-XL | Cisco IOS Software 릴리스 12.0(5)XP, Enterprise Edition | Cisco IOS Software 릴리스 12.0(5)XP, Enterprise Edition | Cisco IOS Software 릴리스 12.0(5)WC(1) 이상 |
WS-C3524-PWR-XL WS-C3524-PWR-XL | Cisco IOS Software 릴리스 12.0(5)XU | Cisco IOS Software 릴리스 12.0(5)XU | Cisco IOS Software 릴리스 12.0(5)WC(1) 이상 |
WS-C2940-8TF-S WS-C2940-8TT-S | ISL 지원 안 함 | Cisco IOS Software 릴리스 12.1(13)AY | 802.1Q용 Cisco IOS Software 릴리스 12.1(13)AY 이상 ISL 지원 안 함 |
WS-C2950-12 WS-C2950-24 WS-C2950C-24 WS-C2950T-24 WS-C2955T-12 WS-C2955C-12 WS-C2955S-12 | ISL 지원 안 함 | Cisco IOS Software 릴리스 12.0(5)WC(1) | 802.1Q용 Cisco IOS Software 릴리스 12.0(5)WC(1) 이상 ISL 지원 안 함 |
WS-C2970G-24T-E | Cisco IOS Software 릴리스 12.1(11)AX | Cisco IOS Software 릴리스 12.1(11)AX | Cisco IOS Software 릴리스 12.1(11)AX 이상 |
참고: 이 표에서는 WS-C2916M-XL만 4MB DRAM 스위치입니다. 목록에 있는 다른 모든 스위치는 8MB DRAM 스위치입니다. 스위치에 4MB 또는 8MB의 DRAM이 있는지 확인하려면 user-level show version 명령을 실행합니다. 자세한 내용은 명령줄 인터페이스를 사용하여 Catalyst 2900XL 및 3500XL 스위치의 소프트웨어 업그레이드의 How to Determine the Amount Of Switch Memory Using Command Line Interface 섹션을 참조하십시오.
Catalyst 4500/4000, 5500/5000 및 6500/6000 스위치의 경우
Catalyst 2948G 및 Catalyst 2980G를 포함하는 Catalyst 4500/4000 시리즈는 802.1Q 트렁킹만 지원합니다. 이 시리즈는 ISL 트렁킹을 지원하지 않습니다.
Catalyst 6500/6000 Series 스위치의 이더넷 포트는 802.1Q 또는 ISL 캡슐화를 지원합니다.
Catalyst 5500/5000 트렁크 지원 포트는 ISL 캡슐화만 지원하거나 ISL 또는 802.1Q를 지원합니다. 이 지원 시나리오는 모듈에 따라 다릅니다. show port capabilities 명령을 실행하여 지원을 확인합니다. 명령 출력에는 트렁킹 용량이 명시적으로 표시됩니다. 예를 들면 다음과 같습니다.
cat5509 show port capabilities 3 Model WS-X5234 Port 3/1 Type 10/100BaseTX Speed auto,10,100 Duplex half,full Trunk encap type 802.1Q,ISL !--- This port supports both 802.1Q and ISL. Trunk mode on,off,desirable,auto,nonegotiate Channel 3/1-2,3/1-4 Broadcast suppression percentage(0-100) Flow control receive-(off,on),send-(off,on) Security yes Membership static,dynamic Fast start yes QOS scheduling rx-(none),tx-(1q4t) CoS rewrite yes ToS rewrite IP-Precedence Rewrite yes UDLD yes AuxiliaryVlan 1..1000,untagged,dot1p,none SPAN source,destination
트렁킹 모드가 트렁크 링크 전체에서 일치하는지 확인합니다. 링크의 한 쪽을 ISL 트렁크로 구성한 경우 링크의 다른 쪽을 ISL로 구성합니다. 마찬가지로, 링크의 한 쪽을 802.1Q로 구성한 경우 링크의 다른 쪽을 802.1Q로 구성합니다.
이 섹션에는 이 문서에서 설명하는 기능을 구성하기 위한 정보가 표시됩니다.
참고: 이 문서에 사용된 명령에 대한 자세한 내용은 Command Lookup Tool(등록된 고객만 해당)을 사용하십시오.
이 문서에서는 이 네트워크 설정을 사용합니다.
이 문서에서는 다음과 같은 스위치 구성을 사용합니다.
이 문서에서는 이 구성을 스위치에 적용합니다.
스위치에서 VTP(VLAN Trunk Protocol) 모드를 설정합니다.
스위치에 두 번째 VLAN, VLAN 2를 추가합니다.
참고: 이러한 VLAN에 포트를 추가합니다.
스위치를 연결하는 고속 이더넷 링크에서 ISL 또는 802.1Q를 사용하여 트렁킹을 활성화합니다.
그러면 트렁크가 모든 VLAN에 대한 트래픽을 전달할 수 있습니다.
워크스테이션이 연결되어 있는 포트에서 스패닝 트리 PortFast를 활성화합니다.
토폴로지에 따라 Catalyst 5500의 포트 3/2 및 3/3과 Catalyst 3524XL 스위치의 포트 FastEthernet0/2 및 FastEthernet0/3에서 스패닝 트리 PortFast를 활성화합니다.
이 절차에서는 트렁킹을 구성하는 데 필요한 명령을 제공합니다. 각 단계에는 Cisco IOS Software 및 CatOS 명령이 포함됩니다. 스위치에서 실행되는 소프트웨어에서 사용할 명령 선택을 기반으로 합니다.
두 스위치 모두에서 VTP를 구성합니다.
이 예에서는 VTP 모드를 투명으로 구성합니다. 스위치를 클라이언트 또는 서버로 구성할 수도 있습니다. 자세한 내용은 VLAN 생성 및 유지 관리를 참조하십시오.
Cisco IOS Software
IOSSwitch#vlan database 3524xl(vlan)#vtp transparent Setting device to VTP TRANSPARENT mode.
CatOS
CatOSSwitch> (enable) set vtp mode transparent VTP domain modified
추가 VLAN을 생성합니다.
예제와 같이 VTP 모드가 투명한 경우 두 스위치에서 이 단계를 완료해야 합니다. 그렇지 않으면 VTP 서버 스위치에 추가 VLAN만 정의하면 됩니다.
Cisco IOS Software
IOSSwitch(vlan)#vlan 2 VLAN 2 added: Name: VLAN0002 IOSSwitch(vlan)#exit APPLY completed. Exiting....
CatOS
CatOSSwitch(enable) set vlan 2 VTP advertisements transmitting temporarily stopped, and will resume after the command finishes. Vlan 2 configuration successful
VLAN에 일부 포트를 할당함과 동시에 필요한 경우 해당 포트에서 PortFast를 활성화합니다.
Cisco IOS Software
IOSSwitch(config)#interface fastethernet 0/2 IOSSwitch(config-if)#switchport access vlan 2 IOSSwitch(config-if)#spanning-tree portfast %Warning: portfast enabled on FastEthernet0/2. !--- Usually, you need to enable PortFast on ports that connect !--- to a single host. When you have enabled PortFast, !--- hubs, concentrators, switches, and bridges that connect to this !--- interface can cause temporary spanning tree loops. !--- Use PortFast with CAUTION. IOSSwitch(config-if)#exit
CatOS
CatOSSwitch> (enable) set vlan 2 3/2 Vlan 2 configuration successful VLAN 2 modified. VLAN 1 modified. VLAN Mod/Ports ---- ----------------------- 2 3/2 CatOSSwitch> (enable) set spantree portfast 3/2 enable
포트에서 트렁킹을 활성화합니다.
Cisco IOS Software
IOSSwitch(config)#interface fastethernet 0/1 IOSSwitch(config-if)#switchport mode trunk
CatOS
CatOS 스위치에 대해서는 이 단계를 생략합니다. 5단계에서는 포트를 트렁크로 지정함과 동시에 캡슐화를 정의합니다.
트렁킹 캡슐화를 ISL 또는 802.1Q(dot1q)로 입력합니다.
Cisco IOS Software
IOSSwitch(config-if)#switchport trunk encapsulation isl OR IOSSwitch(config-if)#switchport trunk encapsulation dot1q
참고: 2940/2950 스위치의 경우 이러한 switchport 명령을 사용하지 마십시오. Catalyst 2940/2950 스위치는 802.1Q 캡슐화만 지원합니다. switchport mode trunk 명령을 사용하여 인터페이스에서 트렁킹을 활성화하면 802.1Q 캡슐화가 자동으로 구성됩니다.
CatOS
CatOSSwitch> (enable) set trunk 3/1 nonegotiate isl Port(s) 3/1 trunk mode set to nonegotiate. Port(s) 3/1 trunk type set to Isl. !--- This switch connects to a 2900XL. !--- Therefore, you must use the nonegotiate option. CatOSSwitch> (enable)
또는
!--- If you want to configure 802.1Q trunking instead, !--- issue this command: CatOSSwitch>(enable) set trunk 3/1 nonegotiate dot1q
트렁킹 모드에는 다음과 같은 여러 옵션이 있습니다. on, off, auto, desirable, auto 및 nonegotiate를 선택합니다. 각각에 대한 자세한 내용은 구성 중인 스위치 제품의 해당 CatOS 소프트웨어 구성 페이지를 참조하십시오.
802.1Q의 경우 링크 전체에서 네이티브 VLAN이 일치하는지 확인합니다. 기본적으로 네이티브 VLAN은 1이거나 포트에서 구성한 VLAN입니다. 네트워크에 VLAN 1이 아닌 네이티브 VLAN이 필요한 경우 네이티브 VLAN을 변경할 수 있습니다. 기본 네이티브 VLAN을 변경할 경우 링크의 다른 쪽에서도 네이티브 VLAN을 변경해야 합니다. 네이티브 VLAN을 변경하려면 다음 명령 중 하나를 실행합니다.
Cisco IOS Software
switchport trunk native vlan vlan-ID
CatOS
set vlan vlan-ID module/port
참고: 이 명령의 모듈/포트는 트렁크 포트입니다.
참고: 이 출력은 3524XL 스위치의 명령 문제를 보여줍니다. 파란색 기울임꼴로 된 코멘트는 특정 명령과 단계를 설명합니다.
Catalyst 3524XL |
---|
3524xl#show running-config Building configuration... Current configuration: ! version 12.0 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname 3524xl ! no logging console enable password mysecret ! ! ! ! ! ip subnet-zero ! ! ! interface fastethernet0/1 switchport mode trunk ! !--- If you have configured 802.1Q, !--- you instead see this output !--- under interface fastethernet0/1: !--- interface fastethernet0/1 !--- switchport trunk encapsulation dot1q !--- switchport mode trunk ! interface fastethernet0/2 switchport access vlan 2 spanning-tree portfast ! interface fastethernet0/3 spanning-tree portfast ! interface fastethernet0/4 ! !--- Output suppressed. ! interface VLAN1 ip address 10.10.10.2 255.255.255.0 no ip directed-broadcast no ip route-cache ! ! line con 0 transport input none stopbits 1 line vty 0 4 password mysecret login line vty 5 15 login ! end |
참고: 이 출력은 5500 스위치의 명령 문제를 보여줍니다. 파란색 기울임꼴로 된 코멘트는 특정 명령과 단계를 설명합니다.
Catalyst 5500 |
---|
cat5509> (enable) show config This command shows non-default configurations only. Use 'show config all' to show both default and non-default configurations. ........ .................. .. begin ! # ***** NON-DEFAULT CONFIGURATION ***** ! ! ! set enablepass $2$FNl3$8MSzcpVMg1H2aWfll13aZ. ! #system set system name cat5509 ! #frame distribution method set port channel all distribution mac both ! #vtp set vtp mode transparent set vlan 1 name default type ethernet mtu 1500 said 100001 state active set vlan 2 set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state active set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state active stp ieee set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state active stp ibm set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state active mode srb aremaxhop 7 stemaxhop 7 backupcrf off ! #ip set interface sc0 1 10.10.10.3/255.255.255.0 10.10.10.255 ! ! # default port status is enable ! ! #module 1 : 4-port 10/100BaseTX Supervisor ! #module 2 : 3-port 1000BaseX Ethernet ! #module 3 : 24-port 10/100BaseTX Ethernet set vlan 2 3/2 set trunk 3/1 nonegotiate isl 1-1005 !--- If you have configured 802.1Q trunk, !--- this line displays as: !--- set trunk 3/1 nonegotiate dot1q 1-1005 set spantree portfast 3/2-3 enable ! #module 4 empty ! #module 5 empty ! #module 6 : 24-port 10BaseF Ethernet ! #module 7 empty ! #module 8 : 24-port 10/100BaseTX Ethernet ! #module 9 empty end cat5509> (enable) |
이 섹션에서는 컨피그레이션이 제대로 작동하는지 확인하는 데 사용할 수 있는 정보를 제공합니다.
일부 show 명령은 출력 인터프리터 툴 에서 지원되는데(등록된 고객만), 이 툴을 사용하면 show 명령 출력의 분석 결과를 볼 수 있습니다.
Catalyst 2900XL/3500XL/2950 스위치의 경우:
show interfaces {fastethernet | gigabitethernet} 모듈/포트 switchport
VLAN 표시
vtp 상태 표시
Catalyst 5500/5000 스위치에서:
show port capabilities 모듈/포트
show port module/port
show trunk module/port
vtp 도메인 표시
show interfaces {fastethernet | gigabitethernet} 모듈/포트 switchport
이 명령을 사용하여 포트의 관리 및 작동 상태를 확인할 수 있습니다. 또한 이 명령을 사용하여 트렁크의 양쪽에서 네이티브 VLAN이 일치하는지 확인합니다. 기본 VLAN은 포트가 802.1Q 트렁킹 모드에 있을 때 태그되지 않은 트래픽을 처리합니다. 네이티브 VLAN에 대한 자세한 내용은 VLAN 생성 및 유지 관리를 참조하십시오.
3524xl#show interfaces fastethernet 0/1 switchport Name: Fa0/1 Switchport: Enabled Administrative mode: trunk Operational Mode: trunk Administrative Trunking Encapsulation: isl Operational Trunking Encapsulation: isl Negotiation of Trunking: Disabled Access Mode VLAN: 0 ((Inactive)) Trunking Native Mode VLAN: 1 (default) Trunking VLANs Enabled: ALL Trunking VLANs Active: 1,2 Pruning VLANs Enabled: 2-1001 Priority for untagged frames: 0 Override vlan tag priority: FALSE Voice VLAN: none Appliance trust: none Self Loopback: No
참고: 802.1Q 트렁킹의 경우 show interface {fastethernet의 출력 | gigabitethernet} module/port switchport 명령이 다음과 같이 변경됩니다.
3524xl#show interfaces fastethernet 0/1 switchport Name: Fa0/1 Switchport: Enabled Administrative mode: trunk Operational Mode: trunk Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: Disabled Access Mode VLAN: 0 ((Inactive)) Trunking Native Mode VLAN: 1 (default) Trunking VLANs Enabled: ALL Trunking VLANs Active: 1,2 Pruning VLANs Enabled: 2-1001 Priority for untagged frames: 0 Override vlan tag priority: FALSE Voice VLAN: none Appliance trust: none Self Loopback: No
VLAN 표시
인터페이스 또는 포트가 올바른 VLAN에 속하는지 확인하려면 이 명령을 사용합니다. 이 예에서는 인터페이스 Fa0/2만 VLAN 2에 속합니다. 나머지 인터페이스는 VLAN 1의 멤버입니다.
3524xl#show vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/3, Fa0/4, Fa0/5, Fa0/6, Fa0/7, Fa0/8, Fa0/9, Fa0/10, Fa0/11, Fa0/12, Fa0/13, Fa0/14, Fa0/15, Fa0/16, Fa0/17, Fa0/18, Fa0/19, Fa0/20, Fa0/21, Fa0/22, Fa0/23, Fa0/24, Gi0/1, Gi0/2 2 VLAN0002 active Fa0/2 1002 fddi-default active 1003 token-ring-default active 1004 fddinet-default active 1005 trnet-default active !--- Output suppressed.
vtp 상태 표시
이 명령을 사용하여 스위치에서 VTP 컨피그레이션을 확인합니다. 이 예에서 VTP 모드는 투명입니다. 올바른 VTP 모드는 네트워크의 토폴로지에 따라 달라집니다. VTP에 대한 자세한 내용은 VLAN 생성 및 유지 관리를 참조하십시오.
3524xl#show vtp status VTP Version : 2 Configuration Revision : 0 Maximum VLANs supported locally : 254 Number of existing VLANs : 6 VTP Operating Mode : Transparent VTP Domain Name : VTP Pruning Mode : Disabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0x74 0x79 0xD3 0x08 0xC0 0x82 0x68 0x63 Configuration last modified by 10.10.10.2 at 3-1-93 00:05:30
show port capabilities 모듈/포트
이 명령을 사용하여 포트가 트렁킹을 수행할 수 있는지 확인합니다.
cat5509 show port capabilities 3/1 Model WS-X5234 Port 3/1 Type 10/100BaseTX Speed auto,10,100 Duplex half,full Trunk encap type 802.1Q,ISL Trunk mode on,off,desirable,auto,nonegotiate Channel 3/1-2,3/1-4 Broadcast suppression percentage(0-100) Flow control receive-(off,on),send-(off,on) Security yes Membership static,dynamic Fast start yes QOS scheduling rx-(none),TX(1q4t) COs rewrite yes ToS rewrite IP-Precedence Rewrite yes UDLD yes AuxiliaryVlan 1..1000,untagged,dot1p,none SPAN source,destination
show port module/port
cat5509> (enable) show port 3/1 Port Name Status Vlan Level Duplex Speed Type ----- ------------------ ---------- ---------- ------ ------ ----- ------------ 3/1 connected trunk normal a-full a-100 10/100BaseTX Port AuxiliaryVlan AuxVlan-Status ----- ------------- -------------- 3/1 none none Port Security Violation Shutdown-Time Age-Time Max-Addr Trap IfIndex ----- -------- --------- ------------- -------- -------- -------- ------- 3/1 disabled shutdown 0 0 1 disabled 12 Port Num-Addr Secure-Src-Addr Age-Left Last-Src-Addr Shutdown/Time-Left ----- -------- ----------------- -------- ----------------- ------------------ 3/1 0 - - - - - !--- Output suppressed.
show trunk module/port
이 명령을 사용하여 트렁킹 상태 및 컨피그레이션을 확인합니다.
cat5509> (enable) show trunk * - indicates vtp domain mismatch Port Mode Encapsulation Status Native vlan -------- ----------- ------------- ------------ ----------- 3/1 nonegotiate isl trunking 1 Port Vlans allowed on trunk -------- --------------------------------------------------------------------- 3/1 1-1005 Port Vlans allowed and active in management domain -------- --------------------------------------------------------------------- 3/1 1-2 Port Vlans in spanning tree forwarding state and not pruned -------- --------------------------------------------------------------------- 3/1 1-2
참고: 802.1Q 트렁킹의 경우 이 명령의 출력이 다음과 같이 변경됩니다.
cat5509> (enable) show trunk * - indicates vtp domain mismatch Port Mode Encapsulation Status Native vlan -------- ----------- ------------- ------------ ----------- 3/1 nonegotiate dot1q trunking 1 Port Vlans allowed on trunk -------- --------------------------------------------------------------------- 3/1 1-1005 Port Vlans allowed and active in management domain -------- --------------------------------------------------------------------- 3/1 1-2 Port Vlans in spanning tree forwarding state and not pruned -------- --------------------------------------------------------------------- 3/1 1-2
vtp 도메인 표시
cat5509> (enable) show vtp domain DomainName Domain Index VTP Version Local Mode Password -------------------------------- ------------ ----------- ----------- ---------- 1 2 Transparent - Vlan-count Max-vlan-storage Config Revision Notifications ---------- ---------------- --------------- ------------- 6 1023 0 disabled Last Updater V2 Mode Pruning PruneEligible on Vlans --------------- -------- -------- ------------------------- 10.10.10.3 disabled disabled 2-1000
현재 이 설정에 사용할 수 있는 특정 문제 해결 정보가 없습니다.
개정 | 게시 날짜 | 의견 |
---|---|---|
1.0 |
14-Nov-2001
|
최초 릴리스 |