MP-BGP EVPN 제어 플레인을 사용하는 VXLAN 설정 및 확인

소개

이 문서에서는 MP-BGP EVPN 제어 플레인을 사용하는 VXLAN 설정에 관해 설명합니다. 

사전 요구 사항

요구 사항

다음 주제에 대한 지식을 보유하고 있으면 유용합니다.

• MPLS 레이어 3 VPN
• MP-BGP도 도움이 될 것입니다. 

사용되는 구성 요소

이 문서는 특정 소프트웨어 및 하드웨어 버전으로 한정되지 않습니다.

이 문서의 정보는 특정 랩 환경의 디바이스를 토대로 작성되었습니다. 이 문서에 사용된 모든 디바이스는 초기화된(기본) 컨피그레이션으로 시작되었습니다. 현재 네트워크가 작동 중인 경우 모든 명령의 잠재적인 영향을 미리 숙지하시기 바랍니다.

배경 정보

이 문서에서는 확인 및 이해도를 높이기 위해 샘플 네트워크 시나리오 및 해당 설정과 관련 출력도 보여줍니다.

VXLAN은 네트워크 가상화를 제공하도록 설계되었습니다. UDP 캡슐화에서는 MAC입니다. 레이어 2 인프라는 레이어 3 언더레이 네트워크를 통해 확장되어 데이터 센터에 있는 서버의 물리적 및 지리적 위치에 의존하지 않는 간소화된 서비스를 제공합니다.

이 문서에서는 MP-BGP EVPN 제어 플레인을 사용하는 VXLAN에 대해 설명합니다. 즉, 오버레이 인프라에서 BGP 프로토콜을 사용하여 업데이트를 보내고 받습니다.

기존 네트워크 배포에서는 STP를 사용했는데, 그로 인해 일부 업링크가 영구적으로 차단 상태가 되었습니다. VXLAN 설계에서는 모든 업링크가 작동하며 언더레이 인프라가 IP 네트워크이므로 ECMP가 활용됩니다.

모든 세부 사항에 대한 논의는 이 문서의 범위를 벗어나지만 몇 가지 중요한 용어가 아래에 나와 있습니다.

VXLAN - Virtual Extensible LAN(가상 확장 LAN)

MP-BGP - Multiprotocol BGP(멀티프로토콜 BGP)

EVPN - Ethernet VPN(이더넷 VPN)

VTEP - Virtual Tunnel End Point(가상 터널 엔드포인트). 리프라고도 합니다. 패킷이 캡슐화 및 캡슐화 해제되는 위치입니다.

스파인 - MPLS L3 VPN의 경로 리플렉터와 매우 유사합니다. 이 디바이스는 하나의 VTEP에서 업데이트를 가져오고 다른 VTEP로 전달합니다.

VNI - VXLAN Network Identifier(VXLAN 네트워크 식별자). 주로 레이어 2 경계를 격리하는 데 사용됩니다. 이 필드는 길이가 24비트이므로 기존 VLAN의 범위 제한을 해결합니다. VTEP의 VNI는 기존 VLAN에 매핑됩니다. 관련 내용은 나중에 설명합니다.

구성 

네트워크 다이어그램

표시된 이미지는 설정 및 확인 측면에 사용됩니다. VXLAN 인프라 관점의 비vpc, vpc, intra-vni, inter-vni 및 외부 연결 설정을 다룹니다. 

설정 

VTEP1

! Enabling features

nv overlay evpn
feature ospf
feature bgp
feature pim
feature interface-vlan
feature vn-segment-vlan-based
feature lacp
feature vpc
feature nv overlay

!

fabric forwarding anycast-gateway-mac 0001.0001.0001 ! This is needed for seamless VM mobility across VTEPS,this configuration is  same on all VTEPS.
ip pim rp-address 192.168.9.9 group-list 224.0.0.0/4 ! SPINE is the RP.

!
ip pim ssm range 232.0.0.0/8

!
vlan 1,10,30,40,100,200

!
vlan 10 ! VLAN 10 is used as layer3 VNI to route Inter-VNI traffic.
 name L3-VNI-VLAN-10
 vn-segment 10000010
 vlan 30 ! The Host A resides on Vlan 30, The below command 'maps' vlan 30 with VNID 10000030.
 vn-segment 10000030
!
vrf context EVPN-L3-VNI-VLAN-10 ! Defining layer3 vrf for Inter-VNI traffic.
 vni 10000010
 rd auto
 address-family ipv4 unicast
 route-target both auto
 route-target both auto evpn

!

interface Vlan10 ! Layer3 VNI associated interface vlan does not have an ip address.
 no shutdown
 vrf member EVPN-L3-VNI-VLAN-10
 ip forward

!

interface Vlan30 ! Associating the Host A Vlan with layer3 vrf.
 no shutdown
 vrf member EVPN-L3-VNI-VLAN-10
 ip address 172.16.30.1/24
 fabric forwarding mode anycast-gateway ! This is needed for seamless VM mobility across VTEPS, same on all VTEPS.

!

interface nve1 ! Nve is logical interface where VXLAN packets are encapsulated and decapsulated.
 no shutdown
 source-interface loopback2
 host-reachability protocol bgp ! This means BGP control plane is used to exchange updates.
 member vni 10000010 associate-vrf ! associate-vrf is used for for layer3 vni.
 member vni 10000030
 suppress-arp 
 mcast-group 239.1.1.10 ! A vlan or set of vlans mapped to VNI can be given identical multicast address, this is used for controlled flooding of arp requests.
!                                      

interface Ethernet1/2 ! Ospf with PIM is used as Underlay.
 description "Going to Spine"
 no switchport
 ip address 192.168.19.1/24
 ip router ospf UNDERLAY area 0.0.0.0
 ip pim sparse-mode
 no shutdown

!

interface Ethernet1/11 ! Port to Host A.
 switchport mode trunk

!

interface loopback2 ! Loopback for BGP Peering.
 description "Loopback for "BGP"
 ip address 192.168.11.11/32
 ip router ospf UNDERLAY area 0.0.0.0
 ip pim sparse-mode

!

router ospf UNDERLAY

!
router bgp 65000
 address-family ipv4 unicast
 address-family l2vpn evpn
 neighbor 192.168.9.9 ! Peering with SPINE.
 remote-as 65000
 update-source loopback2
 address-family ipv4 unicast 
 address-family l2vpn evpn 
 send-community extended
 vrf EVPN-L3-VNI-VLAN-10  
 address-family ipv4 unicast
 advertise l2vpn evpn

!
evpn
 vni 10000030 l2 
 rd auto ! RD is default calculated as VNI:BGP Router ID
 route-target import auto ! RT is default calculated as BGP AS:VNI
 route-target export auto

VTEP2 

!

nv overlay evpn
feature ospf
feature bgp
feature pim
feature interface-vlan
feature vn-segment-vlan-based
feature lacp
feature vpc
feature nv overlay

!

fabric forwarding anycast-gateway-mac 0001.0001.0001

!
ip pim rp-address 192.168.9.9 group-list 224.0.0.0/4

!
ip pim ssm range 232.0.0.0/8
vlan 1,10,30,40,100

!
vlan 10 ! This VTEP is dedicated for external connectivity, there is only layer3 VNI config.
 name L3-VNI-VLAN-10
 vn-segment 10000010

!

vrf context EVPN-L3-VNI-VLAN-10 ! Defining layer3 vrf for Inter-VNI traffic.
 vni 10000010
 rd auto
 address-family ipv4 unicast
 route-target both auto
 route-target both auto evpn

!

interface Vlan10 ! Layer3 VNI associated interface vlan does not have an ip address.
 no shutdown
 vrf member EVPN-L3-VNI-VLAN-10
 ip forward

!

interface Vlan100 ! This vlan is used to peer with external EBGP Peer.
 no shutdown
 vrf member EVPN-L3-VNI-VLAN-10
 ip address 192.168.1.2/24

!

interface nve1
 no shutdown
 source-interface loopback2
 host-reachability protocol bgp
 member vni 10000010 associate-vrf

!

interface Ethernet1/2 ! Ospf and PIM are used in Underlay.
 description "Going to Spine"
 no switchport
 ip address 192.168.29.2/24
 ip router ospf UNDERLAY area 0.0.0.0
 ip pim sparse-mode
 no shutdown

!

interface Ethernet1/12 ! Port to External Peer.
 switchport mode trunk

!

interface loopback2
 ip address 192.168.22.22/32
 ip router ospf UNDERLAY area 0.0.0.0
 ip pim sparse-mode

!

router ospf UNDERLAY

!
router bgp 65000
 address-family ipv4 unicast
 address-family l2vpn evpn
 neighbor 192.168.9.9 ! Peering with SPINE.
 remote-as 65000
 update-source loopback2
 address-family ipv4 unicast
 address-family l2vpn evpn
 send-community extended
 vrf EVPN-L3-VNI-VLAN-10
 address-family ipv4 unicast
 advertise l2vpn evpn
 neighbor 192.168.1.1 ! Peering with External Peer, under vrf.
 remote-as 65111
 update-source Vlan100
 address-family ipv4 unicast 

VTEP3

VTEP3 및 VTEP1의 설정은 거의 동일합니다. 유일한 차이점은 VPC와 VLAN 40에 대한 추가 layer2 VNI입니다.

!

nv overlay evpn
feature ospf
feature bgp
feature pim
feature interface-vlan
feature vn-segment-vlan-based
feature lacp
feature vpc
feature nv overlay

!

fabric forwarding anycast-gateway-mac 0001.0001.0001

!
ip pim rp-address 192.168.9.9 group-list 224.0.0.0/4

!
ip pim ssm range 232.0.0.0/8

!
vlan 1,10,20,30,40

!
vlan 10
 name L3-VNI-VLAN-10
 vn-segment 10000010

!
vlan 30
 vn-segment 10000030

!
vlan 40 ! New host vlan 40.
 vn-segment 10000040

!

vpc domain 2 ! Vpc Configs.
 peer-keepalive destination 10.197.204.103 source 10.197.204.106

!

interface Vlan10
 no shutdown
 vrf member EVPN-L3-VNI-VLAN-10
 ip forward

!

interface Vlan30
 no shutdown
 vrf member EVPN-L3-VNI-VLAN-10
 ip address 172.16.30.1/24

!
 fabric forwarding mode anycast-gateway

!

interface Vlan40 
 no shutdown
 vrf member EVPN-L3-VNI-VLAN-10
 ip address 172.16.40.1/24

!
 fabric forwarding mode anycast-gateway

!

interface port-channel2 
 switchport mode trunk
 vpc 2

!

interface port-channel34
 switchport mode trunk
 spanning-tree port type network
 vpc peer-link

!

interface nve1
 no shutdown
 source-interface loopback2
 host-reachability protocol bgp
 member vni 10000010 associate-vrf
 member vni 10000030
 suppress-arp
 mcast-group 239.1.1.10
 member vni 10000040 !New layer2 VNI for Vlan 40.
 suppress-arp
 mcast-group 239.1.1.20

!

interface Ethernet1/1 ! Connected to VTEP4.
 switchport mode trunk
 channel-group 34 mode active

!

interface Ethernet1/2
 description "going to Spine"
 no switchport
 ip address 192.168.39.3/24
 ip router ospf UNDERLAY area 0.0.0.0
 ip pim sparse-mode
 no shutdown

!

interface Ethernet1/13 ! Connected to N5K, which simulates Host C and D.
 switchport mode trunk
 channel-group 2 mode active

!

interface loopback2
 description "loopback for Bgp"
 ip address 192.168.33.33/32
 ip address 192.168.33.34/32 secondary! For other VTEPs VTEP3 and VTEP4 look as single entity.
 ip router ospf UNDERLAY area 0.0.0.0!This secondary address is needed in Vpc designs.

!

router ospf UNDERLAY

!
router bgp 65000
 address-family ipv4 unicast
 address-family l2vpn evpn
 neighbor 192.168.9.9 remote-as 100
 remote-as 65000
 update-source loopback2
 address-family ipv4 unicast
 address-family l2vpn evpn
 send-community extended
 vrf EVPN-L3-VNI-VLAN-10
 address-family ipv4 unicast
 advertise l2vpn evpn

!
evpn
 vni 10000030 l2
 rd auto
 route-target import auto
 route-target export auto
 vni 10000040 l2
 rd auto
 route-target import auto
 route-target export auto 

VTEP4 

!

nv overlay evpn
feature ospf
feature bgp
feature pim
feature interface-vlan
feature vn-segment-vlan-based
feature lacp
feature vpc
feature nv overlay

!

fabric forwarding anycast-gateway-mac 0001.0001.0001

!
ip pim rp-address 192.168.9.9 group-list 224.0.0.0/4

!
ip pim ssm range 232.0.0.0/8

!
vlan 1,10,20,30,40

!
vlan 10
 name L3-VNI-VLAN-10
 vn-segment 10000010

!
vlan 30
 vn-segment 10000030

!
vlan 40
 vn-segment 10000040

!
vrf context EVPN-L3-VNI-VLAN-10
 vni 10000010
 rd auto
 address-family ipv4 unicast
 route-target both auto
 route-target both auto evpn

!

interface Vlan10
 no shutdown
 vrf member EVPN-L3-VNI-VLAN-10
 ip forward

!

interface Vlan30
 no shutdown
 vrf member EVPN-L3-VNI-VLAN-10
 ip address 172.16.30.1/24

!
 fabric forwarding mode anycast-gateway

!

interface Vlan40
 no shutdown
 vrf member EVPN-L3-VNI-VLAN-10
 ip address 172.16.40.1/24

!
 fabric forwarding mode anycast-gateway

!

interface port-channel2
 switchport mode trunk
 vpc 2

!

interface port-channel34
 switchport mode trunk
 spanning-tree port type network
 vpc peer-link

!

interface nve1
 no shutdown
 source-interface loopback2
 host-reachability protocol bgp
 member vni 10000010 associate-vrf
 member vni 10000030
 suppress-arp
 mcast-group 239.1.1.10
 member vni 10000040
 suppress-arp
 mcast-group 239.1.1.20

!

interface Ethernet1/1 ! Connected to VTEP3.
 switchport mode trunk
 channel-group 34 mode active

!

interface Ethernet1/2
 description "going to spine"
 no switchport
 ip address 192.168.49.4/24
 ip router ospf UNDERLAY area 0.0.0.0
 ip pim sparse-mode
 no shutdown

!

interface Ethernet1/13 ! Connected to N5K, which simulates Host C and D.
 switchport mode trunk
 channel-group 2 mode active

!

router ospf UNDERLAY

!
router bgp 65000
 address-family ipv4 unicast
 address-family l2vpn evpn
 neighbor 192.168.9.9 remote-as 100
 remote-as 65000
 update-source loopback2
 address-family ipv4 unicast
 address-family l2vpn evpn
 send-community extended
 vrf EVPN-L3-VNI-VLAN-10
 address-family ipv4 unicast
 advertise l2vpn evpn

!
evpn
 vni 10000030 l2
 rd auto
 route-target import auto
 route-target export auto
 vni 10000040 l2
 rd auto
 route-target import auto
 route-target export auto 

스파인 

!

nv overlay evpn
feature ospf
feature bgp
feature pim
feature interface-vlan
feature vn-segment-vlan-based
feature lacp
feature vpc
feature nv overlay

!
ip pim rp-address 192.168.9.9 group-list 224.0.0.0/4

!
ip pim ssm range 232.0.0.0/8

!

interface Ethernet1/1 ! To VTEP1.
 ip address 192.168.19.9/24
 ip router ospf UNDERLAY area 0.0.0.0
 ip pim sparse-mode
 no shutdown

!

interface Ethernet1/2 ! To VTEP2.
 ip address 192.168.29.9/24
 ip router ospf UNDERLAY area 0.0.0.0
 ip pim sparse-mode
 no shutdown

!

interface Ethernet1/3 ! To VTEP3.
 ip address 192.168.39.9/24
 ip router ospf UNDERLAY area 0.0.0.0
 ip pim sparse-mode
 no shutdown

!

interface Ethernet1/4 ! To VTEP4.
 ip address 192.168.49.9/24
 ip router ospf UNDERLAY area 0.0.0.0
 ip pim sparse-mode
 no shutdown

!

interface loopback1 ! SPINE is RP(Rendezvous Point).
 ip address 192.168.9.9/32
 ip router ospf UNDERLAY area 0.0.0.0
 ip pim sparse-mode

!

router ospf UNDERLAY

!
router bgp 65000
 log-neighbor-changes
 address-family ipv4 unicast
 address-family l2vpn evpn
 retain route-target all
 template peer VTEP-PEERS
 remote-as 65000
 update-source loopback1
 address-family ipv4 unicast
 send-community both
 route-reflector-client ! Spine treats VTEPs as Route-Reflector Clients.
 address-family l2vpn evpn
 send-community both
 route-reflector-client
 neighbor 192.168.11.11 ! VTEP1.
 inherit peer VTEP-PEERS
 neighbor 192.168.22.22 ! VTEP2.
 inherit peer VTEP-PEERS
 neighbor 192.168.33.33 ! VTEP3.
 inherit peer VTEP-PEERS
 neighbor 192.168.44.44 ! VTEP4.
 inherit peer VTEP-PEERS 

호스트 A

호스트 A는 3750 스위치로 시뮬레이션됩니다.

! This port is the uplink to VTEP1.

interface GigabitEthernet1/0/1
 switchport trunk encapsulation dot1q
 switchport mode trunk

!

interface Vlan30
 ip address 172.16.30.33 255.255.255.0

!

! Below the default route to VTEP1.

ip route 0.0.0.0 0.0.0.0 172.16.30.1

호스트 B 

호스트 B는 외부 피어링 디바이스입니다. 여기서는 N5K가 사용됩니다. 

!

router bgp 65111
 address-family ipv4 unicast

!
 network 172.16.2.2/32 ! Advertsing the external subnet to VXLAN infrastructure.
 neighbor 192.168.1.2 remote-as 65000 ! EBGP Peering with VTEP2.
 address-family ipv4 unicast

!

interface loopback1
 ip address 172.16.2.2/32

!

interface Ethernet1/19 ! Uplink port to VTEP2.
 switchport mode trunk

!

interface Vlan100 
 no shutdown
 ip address 192.168.1.1/24 

호스트 C 및 D

호스트 C 및 D는 Nexus5k에 의해 시뮬레이션되어 IP 주소를 개별 vrfs에 유지합니다.

!

vrf context vni30 ! This vrf simulates the HOST C.
 ip route 0.0.0.0/0 172.16.30.1
vrf context vni40 ! This vrf simulates the HOST D.
 ip route 0.0.0.0/0 172.16.40.1

!

interface Vlan30 ! Addressing for HOST C.
 no shutdown
vrf member vni30
 ip address 172.16.30.2/24

!

interface Vlan40 ! Addressing for HOST D.
 no shutdown
 vrf member vni40
 ip address 172.16.40.2/24

!

interface Ethernet1/20 ! Uplink port to VTEP3 in Port-Channel.
 switchport mode trunk
 channel-group 2 mode active

!

interface Ethernet1/21 ! Uplink port to VTEP4 in Port-Channel.
 switchport mode trunk
 channel-group 2 mode active< /pre>

다음을 확인합니다. 

호스트 A에서 외부 호스트 B로의 연결성

HOST_A#ping 172.16.2.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.2.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/4/9 ms

호스트 A에서 호스트 C로의 연결성(Intra-VNI)

HOST_A#ping 172.16.30.2 
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.30.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/4/9 ms

호스트 A에서 호스트 D로의 연결성(Inter-VNI)

HOST_A#ping 172.16.40.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.40.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/9 ms

호스트 B의 라우팅 테이블(외부 피어)

N5K-5672-1# show ip route bgp
IP Route Table for VRF "default"
'*' denotes best ucast next-hop
'**' denotes best mcast next-hop
'[x/y]' denotes [preference/metric]
'%<string>' in via output denotes VRF <string>

172.16.30.2/32, ubest/mbest: 1/0, pending  ! Host route for Host C.
 *via 192.168.1.2, [20/0], 00:00:22, bgp-65100, external, tag 65000, 
172.16.30.33/32, ubest/mbest: 1/0, pending ! Host route for Host A.
 *via 192.168.1.2, [20/0], 00:00:22, bgp-65100, external, tag 65000, 
172.16.40.2/32, ubest/mbest: 1/0, pending  ! Host route for Host D.
 *via 192.168.1.2, [20/0], 00:00:22, bgp-65100, external, tag 65000,

호스트 경로가 이 외부 BGP 피어에 성공적으로 알려졌음을 확인할 수 있습니다.

제어 플레인 확인

• 이 명령은 기존 VLAN과 VNID의 매핑을 보여줍니다.

 VTEP1# show vxlan
Vlan VN-Segment
==== ==========
10 10000010
30 10000030
40 10000040

• 다음은 MAC가 VTEP에서 로컬로 학습되는지 확인하는 것입니다.

 VTEP1# show mac address-table vlan 30
Legend: 
 * - primary entry, G - Gateway MAC, (R) - Routed MAC, O - Overlay MAC
 age - seconds since last seen,+ - primary entry using vPC Peer-Link,
 (T) - True, (F) - False
 VLAN MAC Address Type age Secure NTFY Ports
---------+-----------------+--------+---------+------+----+------------------
* 30 0006.f63f.e3c1 dynamic 0 F F Eth1/11 ! Mac of HOST A
* 30 8c60.4ff2.f541 dynamic 0 F F nve1(192.168.33.34)! Mac of HOST C installed into mac address table, it was learned from BGP.
G 30 e00e.da2a.2393 static - F F sup-eth1(R)          

• 다음 단계는 경로가 l2rib에 설치되었는지 확인하는 것입니다.

 VTEP1# show l2route evpn mac evi 30
Mac Address Prod Next Hop (s) 
-------------- ------ ---------------
0006.f63f.e3c1 Local Eth1/11 ! Mac of HOST A installed into l2rib. 
8c60.4ff2.f541 BGP 192.168.33.34 ! Mac of HOST C installed into l2rib learnt via BGP.

 VTEP1# show l2route evpn mac-ip evi 30
Mac Address Prod Host IP Next Hop (s) 
-------------- ---- --------------------------------------- ---------------
0006.f63f.e3c1 HMM 172.16.30.33 N/A 
8c60.4ff2.f541 BGP 172.16.30.2 192.168.33.34 ! Mac+IP of Host C learnt across the Vxlan Fabric.

VTEP1# show l2route evpn mac-ip evi 40
Mac Address Prod Host IP Next Hop (s) 
-------------- ---- --------------------------------------- ---------------
8c60.4ff2.f541 BGP 172.16.40.2 192.168.33.34 ! Mac+IP of Host D learnt across the Vxlan Fabric.

• 다음 단계는 l2rib이 업데이트를 l2vpn evpn으로 내보내는지 확인하는 것입니다.

 VTEP1# show bgp l2vpn evpn vni-id 10000030
BGP routing table information for VRF default, address family L2VPN EVPN
BGP table version is 31, local router ID is 192.168.11.11
Status: s-suppressed, x-deleted, S-stale, d-dampened, h-history, *-valid, >-best
Path type: i-internal, e-external, c-confed, l-local, a-aggregate, r-redist, I-i
njected
Origin codes: i - IGP, e - EGP, ? - incomplete, | - multipath, & - backup

Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 192.168.11.11:32797 (L2VNI 10000030)
*>l[2]:[0]:[0]:[48]:[0006.f63f.e3c1]:[0]:[0.0.0.0]/216 ! Mac of Host A in update.
 192.168.11.11 100 32768 i
*>i[2]:[0]:[0]:[48]:[8c60.4ff2.f541]:[0]:[0.0.0.0]/216
 192.168.33.34 100 0 i
* i 192.168.33.34 100 0 i
*>l[2]:[0]:[0]:[48]:[0006.f63f.e3c1]:[32]:[172.16.30.33]/272 ! Mac and IP of Host A in update.
 192.168.11.11 100 32768 i
* i[2]:[0]:[0]:[48]:[8c60.4ff2.f541]:[32]:[172.16.30.2]/272  ! Mac and IP of Host C in update from Spine.
 192.168.33.34 100 0 i                                       
*>i 192.168.33.34 100 0 i

• 다음 단계는 경로가 스파인에 알려지는지 확인하는 것입니다.

 VTEP1# show bgp l2vpn evpn nei 192.168.9.9 advertised-routes

Peer 192.168.9.9 routes for address family L2VPN EVPN:
BGP table version is 31, local router ID is 192.168.11.11
Status: s-suppressed, x-deleted, S-stale, d-dampened, h-history, *-valid, >-best
Path type: i-internal, e-external, c-confed, l-local, a-aggregate, r-redist, I-i
njected
Origin codes: i - IGP, e - EGP, ? - incomplete, | - multipath, & - backup

 Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 192.168.11.11:32797 (L2VNI 10000030)
*>l[2]:[0]:[0]:[48]:[0006.f63f.e3c1]:[0]:[0.0.0.0]/216
 192.168.11.11 100 32768 i
*>l[2]:[0]:[0]:[48]:[0006.f63f.e3c1]:[32]:[172.16.30.33]/272 ! Mac and IP advertised to Spine.
 192.168.11.11 100 32768 i

• 다음 단계는 스파인에서 수신된 경로를 확인하는 것입니다.

 VTEP1# show bgp l2vpn evpn nei 192.168.9.9 routes

Peer 192.168.9.9 routes for address family L2VPN EVPN:
BGP table version is 31, local router ID is 192.168.11.11
Status: s-suppressed, x-deleted, S-stale, d-dampened, h-history, *-valid, >-best
Path type: i-internal, e-external, c-confed, l-local, a-aggregate, r-redist, I-i
njected
Origin codes: i - IGP, e - EGP, ? - incomplete, | - multipath, & - backup

Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 192.168.11.11:32797 (L2VNI 10000030)
*>i[2]:[0]:[0]:[48]:[8c60.4ff2.f541]:[0]:[0.0.0.0]/216
 192.168.33.34 100 0 i
* i 192.168.33.34 100 0 i
* i[2]:[0]:[0]:[48]:[8c60.4ff2.f541]:[32]:[172.16.30.2]/272 ! This is update from Host C in same VNID.
 192.168.33.34 100 0 i                                       
*>i 192.168.33.34 100 0 i

Route Distinguisher: 192.168.11.11:32807 (L2VNI 10000040)
*>i[2]:[0]:[0]:[48]:[8c60.4ff2.f541]:[0]:[0.0.0.0]/216
 192.168.33.34 100 0 i
* i 192.168.33.34 100 0 i
* i[2]:[0]:[0]:[48]:[8c60.4ff2.f541]:[32]:[172.16.40.2]/272 ! This is update from Host D in different VNID.
 192.168.33.34 100 0 i                                       
*>i 192.168.33.34 100 0 i

Route Distinguisher: 192.168.11.11:3 (L3VNI 10000010)
*>i[2]:[0]:[0]:[48]:[8c60.4ff2.f541]:[32]:[172.16.30.2]/272
 192.168.33.34 100 0 i
* i 192.168.33.34 100 0 i
*>i[2]:[0]:[0]:[48]:[8c60.4ff2.f541]:[32]:[172.16.40.2]/272
 192.168.33.34 100 0 i
* i 192.168.33.34 100 0 i
*>i[5]:[0]:[0]:[32]:[172.16.2.2]:[0.0.0.0]/224 ! ! This is update from External Host.
 192.168.22.22 100 0 65100 i

VTEP1# show ip bgp vrf EVPN-L3-VNI-VLAN-10 
BGP routing table information for VRF EVPN-L3-VNI-VLAN-10, address family IPv4 Unicast
BGP table version is 5, local router ID is 192.168.1.254
Status: s-suppressed, x-deleted, S-stale, d-dampened, h-history, *-valid, >-best
Path type: i-internal, e-external, c-confed, l-local, a-aggregate, r-redist, I-injected
Origin codes: i - IGP, e - EGP, ? - incomplete, | - multipath, & - backup

Network            Next Hop Metric LocPrf Weight    Path
*>i172.16.2.2/32   192.168.22.22   100      0       65111 i
*>i172.16.30.2/32  192.168.33.34   100      0       i
* i                192.168.33.34   100      0       i
*>i172.16.40.2/32  192.168.33.34   100      0       i
* i                192.168.33.34   100      0       i

• VTEP1에서는 VNID 10000030만 구성되었으며, 호스트 A의 mac 및 ip가 로컬로 학습되었으며 evpn 경로로 알려졌습니다. 호스트 C의 업데이트가 여기에 수신되어 설치된 것도 관찰했습니다.

• 또한 트래픽을 전달하기 전에 nve 피어를 가동할 수 있습니다.

VTEP1# show nve peers
Interface Peer-IP State LearnType Uptime Router-Mac 
--------- --------------- ----- --------- -------- -----------------
nve1 192.168.22.22 Up CP 01:39:15 0062.ecbf.5325 !  VTEP2
nve1 192.168.33.34 Up CP 01:40:09 f8c2.8823.275f !  VTEP3 and VTEP4 appear as single entity as both are in Vpc.   

VTEP1# sh bgp internal nve-peer-vni
PeerAddress VNI VrfID    GatewayMAC     TunnelID Encap EgressVNI F
 
192.168.22.22 10000010 1 0062.ecbf.5325 0xc0a81616 1    0    0 
192.168.33.34 10000010 1 0062.ecbf.4e4d 0xc0a82122 1    0    0 
192.168.33.34 10000010 1 f8c2.8823.275f 0xc0a82122 1    0    0 
192.168.33.34 10000030 1 0000.0000.0000 0x0        1    0    0 
192.168.33.34 10000040 1 0000.0000.0000 0x0        1    0    0 

문제 해결

• nve 인터페이스가 선택된 경우 캡슐화 및 캡슐화 해제에 대한 카운터의 증분을 확인할 수 있습니다. 

 VTEP1# show interface nve 1
nve1 is up
admin state is up, Hardware: NVE
 MTU 9216 bytes
 Encapsulation VXLAN
 Auto-mdix is turned off
 RX
 ucast: 133 pkts, 22344 bytes - mcast: 0 pkts, 0 bytes
 TX
 ucast: 134 pkts, 22512 bytes - mcast: 0 pkts, 0 bytes

• 필터링에 투명 방화벽을 사용하는 경우 연결된 포트가 허용되는지 확인합니다.

VTEP1# show nve vxlan-params 
VxLAN Dest. UDP Port: 4789

•  Inter-VNI 라우팅에 사용되는 로컬 VTEP MAC 주소 확인. VTEP가 vpc 쌍에 있을 때 보조 주소가 표시됩니다.

 VTEP1# show nve interface
Interface: nve1, State: Up, encapsulation: VXLAN
 VPC Capability: VPC-VIP-Only [not-notified]
 Local Router MAC: e00e.da2a.2393
 Host Learning Mode: Control-Plane
 Source-Interface: loopback2 (primary: 192.168.11.11, secondary: 0.0.0.0)

• 원격 VTEPS MAC 주소 및 피어링 상태 확인.

VTEP1# sh nve internal platform interface nve1 detail
Printing Interface ifindex 0x49000001 detail
|======|=========================|===============|===============|=====|=====|
|Intf |State |PriIP |SecIP |Vnis |Peers|
|======|=========================|===============|===============|=====|=====|
|nve1 |UP |192.168.11.11 |0.0.0.0 |3 |2 | ! Secondary Ip is 0.0.0.0 because this VTEP is not in vpc
|======|=========================|===============|===============|=====|=====|

SW_BD/VNIs of interface nve1:
================================================
|======|======|=========================|======|====|======|========
|Sw BD |Vni |State |Intf |Type|Vrf-ID|Notified
|======|======|=========================|======|====|======|========
|10 |10000010|UP |nve1 |CP |3 |Yes 
|30 |10000030|UP |nve1 |CP |0 |Yes 
|40 |10000040|UP |nve1 |CP |0 |Yes 
|======|======|=========================|======|====|======|========

Peers of interface nve1:
============================================

Peer_ip: 192.168.22.22
 Peer-ID : 1
 State : UP
 Learning : Disabled
 TunnelID : 0xc0a81616
 MAC : 0062.ecbf.5325
 Table-ID : 0x1
 Encap : 0x1

Peer_ip: 192.168.33.34 ! For both VTEP3 and VTEP4
 Peer-ID : 2
 State : UP
 Learning : Disabled
 TunnelID : 0xc0a82122
 MAC : 0062.ecbf.4e4d
 Table-ID : 0x1
 Encap : 0x1

• 피어링 시간 및 VTEP 피어의 VNI 정보 확인.

 VTEP1# show nve peer detail
Details of nve Peers:
----------------------------------------

Peer-Ip: 192.168.22.22
 NVE Interface : nve1
 Peer State : Up
 Peer Uptime : 00:22:17

Router-Mac : 0062.ecbf.5325
 Peer First VNI : 10000010
 Time since Create : 00:22:17

Configured VNIs : 10000010,10000030,10000040
 Provision State : add-complete ! Hardware ready for forwarding.
 Route-Update : Yes
 Peer Flags : RmacL2Rib, TunnelPD, DisableLearn
 Learnt CP VNIs : 10000010
 Peer-ifindex-resp : Yes
----------------------------------------
Peer-Ip: 192.168.33.34
 NVE Interface : nve1
 Peer State : Up
 Peer Uptime : 00:22:10
 Router-Mac : 0062.ecbf.4e4d
 Peer First VNI : 10000010
 Time since Create : 00:22:10
 Configured VNIs : 10000010,10000030,10000040
 Provision State : add-complete ! Hardware ready for forwarding.
 Route-Update : Yes
 Peer Flags : RmacL2Rib, TunnelPD, DisableLearn
 Learnt CP VNIs : 10000010,10000030,10000040
 Peer-ifindex-resp : Yes
----------------------------------------

• BGP와 EVI와의 상호 작용 및 내부 정보가 구축되는 방식 확인. VNI 10000030에 매핑된 VLAN 30의 예가 여기에 표시됩니다.

VTEP1# sh bgp internal evi 10000030
*************************************************
L2RIB bound / VNI Req to L2RIB : Yes / 1
L2VNI Adds / Dels / ALL Dels from L2RIB : 4 / 3 / 1
 First L2VNI Add/Del : Dec 17 19:07:41.680736 / Dec 17 19:10:48.455562
 Last L2VNI Add/Del : Dec 17 19:11:13.916893 / Dec 17 19:10:48.455792
L3VNI Adds / Dels from L2RIB : 2 / 0 / 1
 First L3VNI Add/Del : Dec 17 19:07:41.681313 / never
 Last L3VNI Add/Del : Dec 17 19:11:11.838315 / never
 First/Last All VNI Del : Dec 17 19:10:48.455542 / Dec 17 19:10:48.455543
ALL VNI Del from L2RIB state (cleanup status) : All VNI Not Start (0x000006)
All VNI down loop count : 0
L2RIB is up/registered/local-req: 1/1
L2RIB down: in-prg/up-defer: 0/0
L2RIB register/failures: 1/0
L2RIB deregister/failures: 0/0
L2RIB flow control (#enabled/#disabled): Disabled (0/0)
*************************************************
BGP L2VPN/EVPN RD Information for 192.168.11.11:32797
 L2VNI ID : 10000030 (evi_10000030)
 #Prefixes Local/BRIB : 2 / 4
 #Paths L3VPN->EVPN/EVPN->L3VPN : 129 / 0
*************************************************
==============================================
BGP Configured VNI Information:
 evi_cfg : 0xd87786c8
 VNI ID (Index) : 10000030 (1)
 RD : 192.168.11.11:32797
 Export RTs : 1
 ExportRT cfg list:
 65000:10000030 (auto)
 Import RTs : 1
 ImportRT cfg list:
 65000:10000030 (auto)
 Topo Id : 30
 VTEP IP : 192.168.11.11
 VTEP VPC IP : 0.0.0.0
 Encap Type : 8
 Refcount : #00000003
 Enabled : Yes ! If this is no then check the NVE interface config for this VNID
 Delete Pending : No
 Creation Req : No
 Future RD : NULL
 evi_ctx : 0xd86e554c
 RD/Import RT/Export RT : Yes(Auto)/Yes/Yes
 MAC First Add/Del : Dec 17 19:11:12.45086 / never
 MAC Last Add/Del : Dec 17 19:11:12.45086 / never
 MAC IP First Add/Del : Dec 17 19:11:12.54976 / never
 MAC IP Last Add/Del : Dec 17 19:11:12.54977 / never
 IMET First Add/Del : never / never
 IMET Last Add/Del : never / never

==============================================
++++++++++++++++++++++++++++++++++++++++++
BGP VNI Information for evi_10000030 (0xd86e554c)
 L2VNI ID : 10000030 (evi_10000030)
 RD (rdinfo) : 192.168.11.11:32797 (0xd8811eb0)
 Prefixes (local/total) : 2/4
 Created : Dec 17 19:11:12.37640
 Last Oper Up/Down : Dec 17 19:11:12.37827 / never
 Enabled : Yes
 Delete pending : 0
 Stale : No
 Import pending : 0
 Import in progress : 0
 Encap : VxLAN
 Topo Id : 30
 VTEP IP : 192.168.11.11
 VTEP VPC IP : 0.0.0.0
Router-MAC : 0000.0000.0000
 Active Export RTs : 1
 Active Export RT list : 65000:10000030
 Config Export RTs : 1
 ExportRT cfg list:
 65000:10000030 (auto)
 Export RT chg/chg-pending : 0/0
 Active Import RTs : 1
 Active Import RT list : 65000:10000030
 Config Import RTs : 1
 ImportRT cfg list:
 65000:10000030 (auto)
 Import RT chg/chg-pending : 0/0
 IMET Reg/Unreg from L2RIB : 2/0
 MAC Reg/Unreg from L2RIB : 2/0
 MAC IP Reg/Unreg from L2RIB : 2/0
 IMET Add/Del from L2RIB : 0/0
 MAC Add/Del from L2RIB : 1/0
 MAC IP Add/Del from L2RIB : 1/0
 IMET Dnld/Wdraw to L2RIB : 0/0
 MAC Dnld/Wdraw to L2RIB : 1/0
 MAC IP Dnld/Wdraw to L2RIB : 1/0

• 업데이트가 수신되면 Inter-VNI 또는 Intra-VNI 업데이트인지에 관계없이 올바른 경로 대상(RT)을 수신하고 업데이트를 수신하는 VTEP에 관련 설정이 있는지 확인하십시오. 스파인을 통해 제공되는 VTEP3의 업데이트는 RT 일관성을 위해 여기에서 분석됩니다. VTEP1에 대한 RT 및 RD의 로컬 상태가 이 출력에 표시되었습니다.

  SPINE# show bgp l2vpn evpn 172.16.30.2 ! Update from Spine
  BGP routing table information for VRF default, address family L2VPN EVPN
  Route Distinguisher: 3.3.3.3:32797
  BGP routing table entry for [2]:[0]:[0]:[48]:[8c60.4ff2.f541]:[32]:[172.16.30.2]
  /272, version 25
  Paths: (1 available, best #1)
  Flags: (0x000202) on xmit-list, is not in l2rib/evpn, is not in HW,
  
  Advertised path-id 1
   Path type: internal, path is valid, is best path, remote nh not installed, no 
  labeled nexthop
   AS-Path: NONE, path sourced internal to AS
   192.168.33.34 (metric 5) from 192.168.33.33 (3.3.3.3)
   Origin IGP, MED not set, localpref 100, weight 0
   Received label 10000030 1000001
   Extcommunity: RT:65000:10000010 RT:65000:10000030 SOO:192.168.33.34:0 ENC
  AP:8 Router MAC:0062.ecbf.4e4d
  
  Path-id 1 advertised to peers:
   192.168.11.11 192.168.22.22 192.168.44.44