수신 멀티링크 비동기 및 ISDN 통화에 대해 PRI를 사용하여 액세스 서버 구성

다운로드 옵션

PDF (236.3 KB)
다양한 디바이스에서 Adobe Reader로 보기
ePub (100.4 KB)
iPhone, iPad, Android, Sony Reader 또는 Windows Phone의 다양한 앱에서 보기
Mobi (Kindle) (133.1 KB)
Kindle 디바이스에서 보기 또는 다양한 디바이스의 Kindle 앱에서 보기

업데이트:2008년 1월 29일

문서 ID:6310

편견 없는 언어

본 제품에 대한 문서 세트는 편견 없는 언어를 사용하기 위해 노력합니다. 본 설명서 세트의 목적상, 편견 없는 언어는 나이, 장애, 성별, 인종 정체성, 민족 정체성, 성적 지향성, 사회 경제적 지위 및 교차성에 기초한 차별을 의미하지 않는 언어로 정의됩니다. 제품 소프트웨어의 사용자 인터페이스에서 하드코딩된 언어, RFP 설명서에 기초한 언어 또는 참조된 서드파티 제품에서 사용하는 언어로 인해 설명서에 예외가 있을 수 있습니다. 시스코에서 어떤 방식으로 포용적인 언어를 사용하고 있는지 자세히 알아보세요.

이 번역에 관하여

Cisco는 전 세계 사용자에게 다양한 언어로 지원 콘텐츠를 제공하기 위해 기계 번역 기술과 수작업 번역을 병행하여 이 문서를 번역했습니다. 아무리 품질이 높은 기계 번역이라도 전문 번역가의 번역 결과물만큼 정확하지는 않습니다. Cisco Systems, Inc.는 이 같은 번역에 대해 어떠한 책임도 지지 않으며 항상 원본 영문 문서(링크 제공됨)를 참조할 것을 권장합니다.

소개

많은 환경에서 비동기 및 ISDN 사용자 모두의 수신 통화를 수락할 수 있는 액세스 서버를 구성해야 합니다. 그러면 이러한 사용자는 마치 물리적으로 존재하는 것처럼 네트워크에 원활하게 연결할 수 있습니다. 이러한 설정은 일반적으로 출장을 가거나 재택 근무자이거나 SOHO(Small Office-Home Office) 사이트용 네트워크 연결을 제공하는 데 사용됩니다.

이 문서에서는 ISDN T1 PRI 회로에서 수신 비동기 및 ISDN 호출을 허용하도록 액세스 서버를 구성하는 방법에 대해 설명합니다. 컨피그레이션은 NAS(Network Access Server)가 통화를 수락하는 데 필요한 최소 설정을 제공합니다. 필요에 따라 이 구성에 추가 기능을 추가할 수 있습니다.

사전 요구 사항

요구 사항

이 문서에 대한 특정 요건이 없습니다.

사용되는 구성 요소

이 문서의 정보는 다음 소프트웨어 및 하드웨어 버전을 기반으로 합니다.

Cisco IOS® Software Release 12.2(5)를 실행하는 192개의 MICA 모뎀과 8개의 T1 포트가 포함된 Cisco AS5300
T1 PRI 2개
Microsoft Windows를 실행하는 PC입니다. 이 PC에는 아날로그 모뎀과 공용 스위치 전화 네트워크에 대한 전화 연결이 있습니다. PC는 AS5300에 연결된 T1 PRI에 전화를 겁니다.
ISDN BRI 회로가 있는 Cisco 800 및 1600 Series 라우터 이러한 라우터는 ISDN 전화 접속 클라이언트입니다. Cisco 1600에 대한 컨피그레이션이 제공됩니다. BRI 인터페이스가 있는 모든 라우터에 이 클라이언트 컨피그레이션을 적용할 수 있습니다.
AAA(Local Authentication, Authorization and Accounting). AAA Radius 또는 Tacacs+ 서버가 있는 경우 둘 중 하나를 사용하여 수신 통화에 대해 AAA를 제공할 수 있습니다.

참고: Cisco 800 라우터의 컨피그레이션은 Cisco 1600 라우터의 컨피그레이션과 유사하며 이 문서에는 포함되지 않습니다.

이 문서의 정보는 특정 랩 환경의 디바이스를 토대로 작성되었습니다. 이 문서에 사용된 모든 디바이스는 초기화된(기본) 컨피그레이션으로 시작되었습니다. 현재 네트워크가 작동 중인 경우, 모든 명령어의 잠재적인 영향을 미리 숙지하시기 바랍니다.

maui-nas-02(5300)
마우이-소호-01 (1600)

maui-nas-02(5300)
maui-nas-02#show running-config Building configuration... Current configuration : 3671 bytes ! ! No configuration change since last restart ! version 12.2 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname maui-nas-02 ! boot system flash:c5300-i-mz.122-5.bin aaa new-model aaa authentication login default local aaa authentication login NO_AUTHEN none aaa authentication ppp default local aaa authorization network default local !--- PPP authentication and network authorization are local. !--- Replace local* with radius or tacacs if you use an AAA server.* enable secret 5 <deleted> ! username admin password 7 <deleted> username async_user password 7 <deleted> username travis_isdn password 7 <deleted> username austin_isdn password 7 <deleted> !--- Usernames for local authentication of the call. !--- The client presents the username/password and the NAS !--- authenticates the peer. spe 1/0 1/8 firmware location mica-modem-pw.2.7.3.0.bin spe 2/0 2/7 firmware location mica-modem-pw.2.7.3.0.bin ! ip subnet-zero ip domain-name maui-onions.com !--- Tells the NAS how to qualify DNS lookups. !--- In this example, maui-onions.com is appended to the end of each !--- looked-up name. ip name-server 172.22.53.210 !--- Specifies the primary name server. ! async-bootp dns-server 172.22.53.210 !--- Specifies (for async clients) the IP address of domain name servers. isdn switch-type primary-ni !--- Switch-type for this NAS. Obtain this information from the Telco. ! controller T1 0 !--- First T1 PRI framing esf !--- Framing for this T1 is Extended Super Frame (ESF). !--- Obtain this information from the Telco. clock source line primary !--- T1 0 is the primary clock source for this NAS. !--- Clock source must be specified for the timing and synchronization !--- of the T1 carrier. linecode b8zs !--- Linecoding for this T1. Obtain this information from the Telco. pri-group timeslots 1-24 !--- For T1 PRI scenarios, all 24 T1 timeslots are assigned as !--- ISDN PRI channels. The router now automatically creates the !--- corresponding D-channel: interface Serial 0:23. ! controller T1 1 !--- Second T1 PRI. framing esf !--- Framing for this T1 is Extended Super Frame (ESF). !--- Obtain this information from the Telco. clock source line secondary 1 !--- T1 1 is the first secondary clock source for this NAS. !--- If the primary clock fails, this secondary clock takes over. linecode b8zs !--- Linecoding for this T1. Obtain this information from the Telco. pri-group timeslots 1-24 !--- For T1 PRI scenarios, all 24 T1 timeslots are assigned as ISDN !--- PRI channels. The router now automatically creates the !--- corresponding D-channel: interface Serial 1:23. ! controller T1 2 !--- This T1 is unused. framing sf clock source line secondary 2 linecode ami ! !--- Unused interface configuration is omitted here. ! interface Loopback0 ip address 172.22.60.1 255.255.255.0 !--- The IP pool for async users is in this subnet. !--- The routes for all async clients are summarized and !--- propagated to the backbone instead of 254 routes. ! interface Loopback1 ip address 172.22.61.1 255.255.255.0 !--- The IP pool for ISDN users is in this subnet. !--- The routes for all ISDN clients are summarized and !--- propagated to the backbone instead of 254 routes. ! interface Ethernet0 ip address 172.22.53.140 255.255.255.0 ! !--- Unused interface configuration is omitted here. ! interface Serial0:23 !--- D-channel configuration for T1 0. no ip address encapsulation ppp !--- PPP encapsulation on this interface. dialer rotary-group 10 !--- T1 0 is a member of rotary group 10. !--- The rotary group configuration is in interface Dialer 10. isdn switch-type primary-ni isdn incoming-voice modem !--- All incoming voice calls on this T1 are sent to the modems. !--- This command is required if this T1 is to accept async calls. no cdp enable ppp authentication chap ppp multilink ! interface Serial1:23 !--- D-channel configuration for T1 1. no ip address encapsulation ppp !--- PPP encapsulation on this interface. dialer rotary-group 10 !--- T1 1 is a member of rotary group 10. !--- The rotary group configuration is in interface Dialer 10. isdn switch-type primary-ni isdn incoming-voice modem !--- All incoming voice calls on this T1 are sent to the modems. !--- This command is required if this T1 is to accept async calls. no cdp enable ppp authentication chap ppp multilink ! interface Group-Async0 !--- This group-async interface is the configuration template for all modems. !--- You need not configure individual async interfaces because you can !--- clone the interfaces from one managed copy. ip unnumbered Loopback0 !--- A Loopback interface is always up/up. So, unnumber the loopback interface !--- for stability. encapsulation ppp dialer in-band dialer idle-timeout 900 dialer-group 5 !--- Interesting traffic is defined in dialer-list 5. !--- Note: The specified dialer-group number must be the same as the !--- dialer-list number. In this example, the number is defined as "5". async mode interactive !--- Users can dial in and get to a shell or PPP session on that line. !--- You can use this command in conjunction with autoselect ppp !--- under the line configuration to automatically detect the connection type. peer default ip address pool ASYNC !--- Clients are assigned addresses from the IP address pool named ASYNC. no fair-queue ppp authentication chap !--- Use CHAP authentication. ppp multilink group-range 1 192 !--- Modems 1 through 192 are members of this group async interface. ! interface Dialer10 !--- Configuration for rotary group 10. !--- The Dialer interface number (10) must exactly match rotary !--- group number configured on the physical interfaces. ip unnumbered Loopback1 !--- A Loopback interface is always up/up. So, unnumber the loopback interface !--- for stability. encapsulation ppp dialer in-band !--- Enable V.25bis on this interface. dialer idle-timeout 900 !--- Idle timeout for incoming calls is 900 seconds (15 mins). dialer-group 5 !--- Apply interesting traffic definition from dialer-list 5. !--- Note: The specified dialer-group number must be the same !--- as the dialer-list number. !--- In this example, the number is defined as "5". peer default ip address pool ISDN !--- Clients are assigned addresses from the IP address pool named ISDN. ppp authentication chap ppp multilink ! router eigrp 69 network 172.22.0.0 auto-summary no eigrp log-neighbor-changes ! ip local pool ASYNC 172.22.60.2 172.22.60.254 ip local pool ISDN 172.22.61.2 172.22.61.254 !--- IP address pools for dialin clients. ip classless no ip http server ! access-list 101 remark Interesting Traffic Definition to be used in dialer-list 5 access-list 101 deny eigrp any any access-list 101 permit ip any any dialer-list 5 protocol ip list 101 !--- Access-list 101 defines interesting traffic. This definition is applied !--- to interface Dialer 10 and Group-Async 0 through dialer-group 5. !--- Note: The specified dialer-list number must be the same as the !--- dialer-group number. In this example, the number is defined as "5". ! line con 0 exec-timeout 0 0 login authentication NO_AUTHEN !--- Apply AAA list NO_AUTHEN configured previously. !--- That list has method "none". !--- There is no authentication on the console port. line 1 192 modem InOut !--- Support incoming and outgoing modem calls. transport input all autoselect during-login ! --- Displays the username:password prompt after modems connect. autoselect ppp !--- Automatically launches PPP if the router detects incoming PPP packets. !--- Without this command the dialin client must manually !--- launch PPP (from Exec mode). line aux 0 line vty 0 4 ! ntp clock-period 17180107 ntp server 172.22.53.1 end

maui-nas-02(5300)

maui-nas-02#show running-config 
 Building configuration...

 Current configuration : 3671 bytes
 !
 ! No configuration change since last restart
 !
 version 12.2
 service timestamps debug datetime msec
 service timestamps log datetime msec
 service password-encryption
 !
 hostname maui-nas-02
 !
 boot system flash:c5300-i-mz.122-5.bin
 aaa new-model
 aaa authentication login default local
 aaa authentication login NO_AUTHEN none
 aaa authentication ppp default local
 aaa authorization network default local 
 
!--- PPP authentication and network authorization are local. !--- Replace local with radius or tacacs if you use an AAA server.

 enable secret 5 <deleted>
 !
 username admin password 7 <deleted>
 username async_user password 7 <deleted>
 username travis_isdn password 7 <deleted>
 username austin_isdn password 7 <deleted>
 
!--- Usernames for local authentication of the call. !--- The client presents the username/password and the NAS !--- authenticates the peer.

 spe 1/0 1/8
  firmware location mica-modem-pw.2.7.3.0.bin
 spe 2/0 2/7
  firmware location mica-modem-pw.2.7.3.0.bin
 !
 ip subnet-zero
 ip domain-name maui-onions.com
 
!--- Tells the NAS how to qualify DNS lookups. !--- In this example, maui-onions.com is appended to the end of each !--- looked-up name.

 ip name-server 172.22.53.210
 
!--- Specifies the primary name server.

 !
 async-bootp dns-server 172.22.53.210
 
!--- Specifies (for async clients) the IP address of domain name servers. 

 isdn switch-type primary-ni
 
!--- Switch-type for this NAS. Obtain this information from the Telco.

 !
 controller T1 0
 
!--- First T1 PRI

  framing esf
 
!--- Framing for this T1 is Extended Super Frame (ESF). !--- Obtain this information from the Telco.

  clock source line primary
 
!--- T1 0 is the primary clock source for this NAS. !--- Clock source must be specified for the timing and synchronization !--- of the T1 carrier.

  linecode b8zs
 
!--- Linecoding for this T1. Obtain this information from the Telco.

  pri-group timeslots 1-24
 
!--- For T1 PRI scenarios, all 24 T1 timeslots are assigned as !--- ISDN PRI channels. The router now automatically creates the !--- corresponding D-channel: interface Serial 0:23.

 !
 controller T1 1
 
!--- Second T1 PRI.

  framing esf
 
!--- Framing for this T1 is Extended Super Frame (ESF). !--- Obtain this information from the Telco.

  clock source line secondary 1
 
!--- T1 1 is the first secondary clock source for this NAS. !--- If the primary clock fails, this secondary clock takes over.

  linecode b8zs
 
!--- Linecoding for this T1. Obtain this information from the Telco.

  pri-group timeslots 1-24
 
!--- For T1 PRI scenarios, all 24 T1 timeslots are assigned as ISDN !--- PRI channels. The router now automatically creates the !--- corresponding D-channel: interface Serial 1:23.

 !
 controller T1 2
 
!--- This T1 is unused.

  framing sf
  clock source line secondary 2
  linecode ami
 !
 
!--- Unused interface configuration is omitted here.

 !
 interface Loopback0
  ip address 172.22.60.1 255.255.255.0
 
!--- The IP pool for async users is in this subnet. !--- The routes for all async clients are summarized and !--- propagated to the backbone instead of 254 routes.

 !
 interface Loopback1
  ip address 172.22.61.1 255.255.255.0
 
!--- The IP pool for ISDN users is in this subnet. !--- The routes for all ISDN clients are summarized and !--- propagated to the backbone instead of 254 routes.

 !
 interface Ethernet0
  ip address 172.22.53.140 255.255.255.0
 !         
 
!--- Unused interface configuration is omitted here.

 !
 interface Serial0:23
 
!--- D-channel configuration for T1 0.

  no ip address
  encapsulation ppp

 !--- PPP encapsulation on this interface.

  dialer rotary-group 10
 
!--- T1 0 is a member of rotary group 10. !--- The rotary group configuration is in interface Dialer 10.

  isdn switch-type primary-ni
  isdn incoming-voice modem
 
!--- All incoming voice calls on this T1 are sent to the modems. !--- This command is required if this T1 is to accept async calls.

  no cdp enable
  ppp authentication chap
  ppp multilink
 !
 interface Serial1:23
 
!--- D-channel configuration for T1 1.

  no ip address
  encapsulation ppp
 
!--- PPP encapsulation on this interface.

  dialer rotary-group 10
 
!--- T1 1 is a member of rotary group 10. !--- The rotary group configuration is in interface Dialer 10.

  isdn switch-type primary-ni
  isdn incoming-voice modem
 
!--- All incoming voice calls on this T1 are sent to the modems. !--- This command is required if this T1 is to accept async calls.

  no cdp enable
  ppp authentication chap
  ppp multilink
 !
 interface Group-Async0
 
!--- This group-async interface is the configuration template for all modems. !--- You need not configure individual async interfaces because you can !--- clone the interfaces from one managed copy.

  ip unnumbered Loopback0
 
!--- A Loopback interface is always up/up. So, unnumber the loopback interface !--- for stability.

  encapsulation ppp
  dialer in-band
  dialer idle-timeout 900
  dialer-group 5
 
!--- Interesting traffic is defined in dialer-list 5. !--- Note: The specified dialer-group number must be the same as the !--- dialer-list number. In this example, the number is defined as "5".

  async mode interactive
 
!--- Users can dial in and get to a shell or PPP session on that line. !--- You can use this command in conjunction with autoselect ppp !--- under the line configuration to automatically detect the connection type.

  peer default ip address pool ASYNC
 
!--- Clients are assigned addresses from the IP address pool named ASYNC.

  no fair-queue
  ppp authentication chap
 
!--- Use CHAP authentication.

  ppp multilink
  group-range 1 192
 
!--- Modems 1 through 192 are members of this group async interface.

 !
 interface Dialer10
 
!--- Configuration for rotary group 10. !--- The Dialer interface number (10) must exactly match rotary !--- group number configured on the physical interfaces.

  ip unnumbered Loopback1
 
!--- A Loopback interface is always up/up. So, unnumber the loopback interface !--- for stability.

  encapsulation ppp
  dialer in-band

 !--- Enable V.25bis on this interface.

  dialer idle-timeout 900
 
!--- Idle timeout for incoming calls is 900 seconds (15 mins).

  dialer-group 5
 
!--- Apply interesting traffic definition from dialer-list 5. !--- Note: The specified dialer-group number must be the same !--- as the dialer-list number. !--- In this example, the number is defined as "5".

  peer default ip address pool ISDN
 
!--- Clients are assigned addresses from the IP address pool named ISDN.

  ppp authentication chap
  ppp multilink
 !
 router eigrp 69
  network 172.22.0.0
  auto-summary
  no eigrp log-neighbor-changes
 !
 ip local pool ASYNC 172.22.60.2 172.22.60.254
 ip local pool ISDN 172.22.61.2 172.22.61.254
 
!--- IP address pools for dialin clients.

 ip classless
 no ip http server
 !
 access-list 101 remark Interesting Traffic Definition to be 
 used in dialer-list 5
 access-list 101 deny   eigrp any any
 access-list 101 permit ip any any
 dialer-list 5 protocol ip list 101
 
!--- Access-list 101 defines interesting traffic. This definition is applied !--- to interface Dialer 10 and Group-Async 0 through dialer-group 5. !--- Note: The specified dialer-list number must be the same as the !--- dialer-group number. In this example, the number is defined as "5".

 !
 line con 0
  exec-timeout 0 0
  login authentication NO_AUTHEN
 
!--- Apply AAA list NO_AUTHEN configured previously. !--- That list has method "none". !--- There is no authentication on the console port.

 line 1 192
  modem InOut
 
!--- Support incoming and outgoing modem calls.

  transport input all
  autoselect during-login
 !
--- Displays the username:password prompt after modems connect.

  autoselect ppp
 
!--- Automatically launches PPP if the router detects incoming PPP packets. !--- Without this command the dialin client must manually !--- launch PPP (from Exec mode).

 line aux 0
 line vty 0 4
 !
 ntp clock-period 17180107
 ntp server 172.22.53.1
 end

마우이-소호-01 (1600)
maui-soho-01#show running-config Building configuration... Current configuration : 1609 bytes ! version 12.1 no service single-slot-reload-enable service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname maui-soho-01 ! logging rate-limit console 10 except errors ! username admin password 7 <deleted> ip subnet-zero no ip finger ! isdn switch-type basic-ni !--- Switch-type for the BRI circuit. Obtain this information from the Telco. ! interface Ethernet0 ip address 10.0.0.1 255.255.255.0 no keepalive ! interface Serial0 no ip address shutdown ! interface BRI0 !--- BRI physical interface configuration. no ip address !--- An IP address is not required on the physical BRI interface because !--- this is a dialer pool. !--- The IP addressing functionality is in interface Dialer 1 (dialer pool). encapsulation ppp dialer pool-member 1 !--- Places the interface into dialer pool 1 from which Dialer interfaces !--- can draw channels as needed. !--- Links the physical interface with the logical dialer interfaces. !--- Dialer Pool 1 is defined in interface Dialer 1. isdn switch-type basic-ni isdn spid1 51255511110101 5551111 isdn spid2 51255511120101 5551112 !--- Service Profile IDentifiers (SPIDs) are found primarily in North America. !--- SPIDs are not required for certain switch types. Confirm with your Telco. !--- If the Telco informs you that you do not need SPIDs, do not use these !--- two SPID commands. ppp authentication chap callin !--- Perform one way CHAP authentication. ppp multilink !--- Permit multilink on this BRI interface. ! interface Dialer1 !--- This dialer is the logical interface for the dialer pool. ip address negotiated !--- IP address for this interface is obtained from the NAS during !--- IPCP negotiation. Alternatively, you can also unnumber this interface !--- to a working interface (example, ethernet 0). encapsulation ppp dialer pool 1 !--- Defines Dialer pool 1. !--- BRI 0 is a member of this pool. dialer idle-timeout 900 !--- Idle-timout for this link is 900 seconds (15 minutes). !--- The link is disconnected if there is no interesting traffic for 900 secs. dialer string 81560 class 56k !--- Dial 81560 and use the map-class named "56k". dialer load-threshold 1 outbound !--- Sets the outbound load level for traffic at which !--- additional connections are added to the MP bundle load level. !--- Values range from 1 (unloaded) to 255 (fully loaded). !--- With a threshold of 1, the additional links are immediately !--- brought up and added to the bundle. dialer-group 1 !--- Apply interesting traffic definition from dialer-list 1. ppp authentication chap callin !--- Use one way PPP CHAP authentication. ppp chap hostname austin_isdn !--- Use the CHAP username austin_isdn to authenticate to the other router. ppp chap password 7 <deleted> !--- Use this CHAP password to authenticate to the other router. ppp multilink !--- Allow multilink for the dialer profile. !--- Without this command multilink is NOT negotiated. ! ! ip classless ip route 0.0.0.0 0.0.0.0 Dialer1 !--- Set the default route to be interface Dialer 1 (the dialer pool). !--- Traffic sent to int Dialer1 causes the dialer pool member (int BRI 0) !--- to be dialed. no ip http server ! ! map-class dialer 56k !--- Map-class named "56k" that you used with the dialer string in int Dialer1. dialer isdn speed 56 !--- Set the speed of the call to be 56k (the default speed is 64k). !--- This setting is optional for your connection. !--- Consult your Telco to find out if you need to configure the dial !--- speed to 56k. access-list 101 remark Interesting traffic for dialer-list 1 access-list 101 deny udp any any eq ntp access-list 101 permit ip any any !--- Define NTP traffic as NOT interesting to prevent periodic NTP traffic !--- from keeping the link up indefinitely. !--- All other IP traffic is interesting. !--- Change this depending on your traffic needs. dialer-list 1 protocol ip list 101 !--- Access-list 101 defines interesting traffic. !--- Apply this to interface Dialer 1 through the command dialer-group 1. !--- Note: The specified dialer-list number must be the same as the !--- dialer-group number. In this example, the number is defined as "1" ! line con 0 transport input none line vty 0 4 login ! ntp clock-period 17042429 ntp server 172.22.53.1 end

마우이-소호-01 (1600)

maui-soho-01#show running-config
 Building configuration...

 Current configuration : 1609 bytes
 !
 version 12.1
 no service single-slot-reload-enable
 service timestamps debug datetime msec
 service timestamps log datetime msec
 service password-encryption
 !
 hostname maui-soho-01
 !
 logging rate-limit console 10 except errors
 !
 username admin password 7 <deleted>
 ip subnet-zero
 no ip finger
 !
 isdn switch-type basic-ni
 
!--- Switch-type for the BRI circuit. Obtain this information from the Telco.

 !
 interface Ethernet0
  ip address 10.0.0.1 255.255.255.0
  no keepalive
 !
 interface Serial0
  no ip address
  shutdown
 !
 interface BRI0
 
!--- BRI physical interface configuration.

  no ip address
 
!--- An IP address is not required on the physical BRI interface because !--- this is a dialer pool. !--- The IP addressing functionality is in interface Dialer 1 (dialer pool).

  encapsulation ppp
  dialer pool-member 1 
 
!--- Places the interface into dialer pool 1 from which Dialer interfaces !--- can draw channels as needed. !--- Links the physical interface with the logical dialer interfaces. !--- Dialer Pool 1 is defined in interface Dialer 1.

  isdn switch-type basic-ni
  isdn spid1 51255511110101 5551111
  isdn spid2 51255511120101 5551112
 
!--- Service Profile IDentifiers (SPIDs) are found primarily in North America. !--- SPIDs are not required for certain switch types. Confirm with your Telco. !--- If the Telco informs you that you do not need SPIDs, do not use these !--- two SPID commands.

  ppp authentication chap callin
 
!--- Perform one way CHAP authentication.

  ppp multilink
 
!--- Permit multilink on this BRI interface.

 !
 interface Dialer1
 
!--- This dialer is the logical interface for the dialer pool.

  ip address negotiated
 
!--- IP address for this interface is obtained from the NAS during !--- IPCP negotiation. Alternatively, you can also unnumber this interface !--- to a working interface (example, ethernet 0).

encapsulation ppp
  dialer pool 1
 
!--- Defines Dialer pool 1. !--- BRI 0 is a member of this pool.

  dialer idle-timeout 900
 
!--- Idle-timout for this link is 900 seconds (15 minutes). !--- The link is disconnected if there is no interesting traffic for 900 secs.

  dialer string 81560 class 56k
 
!--- Dial 81560 and use the map-class named "56k".

  dialer load-threshold 1 outbound
 
!--- Sets the outbound load level for traffic at which !--- additional connections are added to the MP bundle load level. !--- Values range from 1 (unloaded) to 255 (fully loaded). !--- With a threshold of 1, the additional links are immediately !--- brought up and added to the bundle.

  dialer-group 1
 
!--- Apply interesting traffic definition from dialer-list 1.

  ppp authentication chap callin
 
!--- Use one way PPP CHAP authentication.

  ppp chap hostname austin_isdn
 
!--- Use the CHAP username austin_isdn to authenticate to the other router.

  ppp chap password 7 <deleted>
 
!--- Use this CHAP password to authenticate to the other router.

  ppp multilink
 
!--- Allow multilink for the dialer profile. !--- Without this command multilink is NOT negotiated.

 !
 !
 ip classless
 ip route 0.0.0.0 0.0.0.0 Dialer1
 
!--- Set the default route to be interface Dialer 1 (the dialer pool). !--- Traffic sent to int Dialer1 causes the dialer pool member (int BRI 0) !--- to be dialed.

 no ip http server
 !
 !
 map-class dialer 56k
 
!--- Map-class named "56k" that you used with the dialer string in int Dialer1.

  dialer isdn speed 56
 
!--- Set the speed of the call to be 56k (the default speed is 64k). !--- This setting is optional for your connection. !--- Consult your Telco to find out if you need to configure the dial !--- speed to 56k.

 access-list 101 remark Interesting traffic for dialer-list 1
 access-list 101 deny   udp any any eq ntp
 access-list 101 permit ip any any
 
!--- Define NTP traffic as NOT interesting to prevent periodic NTP traffic !--- from keeping the link up indefinitely. !--- All other IP traffic is interesting. !--- Change this depending on your traffic needs.

 dialer-list 1 protocol ip list 101
 
!--- Access-list 101 defines interesting traffic. !--- Apply this to interface Dialer 1 through the command dialer-group 1. !--- Note: The specified dialer-list number must be the same as the !--- dialer-group number. In this example, the number is defined as "1"

 !
 line con 0
  transport input none
 line vty 0 4
  login
 !
 ntp clock-period 17042429
 ntp server 172.22.53.1
 end

다음을 확인합니다.

이 섹션에서는 컨피그레이션이 제대로 작동하는지 확인하는 데 사용할 수 있는 정보를 제공합니다.

일부 show 명령은 출력 인터프리터 툴 에서 지원되는데(등록된 고객만), 이 툴을 사용하면 show 명령 출력의 분석 결과를 볼 수 있습니다.

show isdn status - 라우터가 ISDN 스위치와 제대로 통신하는지 확인합니다. 출력에서 레이어 1 상태가 ACTIVE이고 레이어 2 상태 = MULTIPLE_FRAME_ESTABLISHED가 나타나는지 확인합니다. 이 명령은 활성 통화 수도 표시합니다. 자세한 내용은 BRI 문제 해결을 위해 show isdn status 명령 사용을 참조하십시오.
show ppp multilink - 활성 멀티링크 번들에 대한 정보를 표시합니다. 멀티링크 연결을 확인하려면 이 명령을 사용합니다.
show dialer [interface type number]—DDR용으로 구성된 인터페이스에 대한 일반 진단 정보를 표시합니다. 다이얼러가 제대로 작동하면 다이얼러 상태가 데이터 링크 계층 위로 메시지가 나타나야 합니다. 물리적 레이어가 위로 나타나면 그 라인 프로토콜이 작동했지만 NCP(Network Control Protocol)는 나타나지 않았다는 의미입니다. 다이얼링을 시작한 패킷의 소스 및 목적지 주소가 다이얼 이유 회선에 표시됩니다. 이 show 명령은 타이머의 컨피그레이션 및 연결이 시간 초과되기 전의 시간도 표시합니다.
show caller user username detail—특정 사용자에 대한 매개변수(예: 할당된 IP 주소, PPP 및 PPP 번들 매개변수)를 표시합니다. 사용 중인 버전의 Cisco IOS 소프트웨어가 이 명령을 지원하지 않는 경우 show user 명령을 사용합니다.
show dialer map - 구성된 동적 및 정적 다이얼러 맵을 표시합니다. 이 명령을 사용하여 동적 다이얼러 맵이 생성되었는지 확인할 수 있습니다. 다이얼러 맵이 없으면 패킷을 라우팅할 수 없습니다.

샘플 show 출력

다음은 성공한 통화에 대한 show 명령 출력입니다. 굵게 표시된 부분과 출력에 제공된 주석에 유의하십시오. 가져온 출력을 여기에 표시된 결과와 비교합니다.

일반 보기

maui-nas-02#show users
  Line         User       Host(s)              Idle       Location
* 0 con 0                 idle                 00:00:00   
  97 tty 97    async_user Async interface      00:06:36   PPP: 172.22.60.2

!--- Async User. The IP address of the peer is indicated.


  Interface    User        Mode                Idle     Peer Address
  Vi1          austin_isd Virtual PPP (Bundle) 00:03:35 172.22.61.2
     Vi2          travis_isd Virtual PPP (Bundle) 00:00:20 172.22.61.3

!--- Virtual-Access Interface for the two multilink PPP users.

  Se0:1        austin_isd Sync PPP                    -   Bundle: Vi1
     Se0:2        austin_isd Sync PPP                    -   Bundle: Vi1

!--- User austin_isdn is connected through two B-channels(Multilink PPP). !--- Interface Virtual-Access 1 (Vi1) controls the two B-channels.

     Se0:3        travis_isd Sync PPP                    -   Bundle: Vi2
     Se0:4        travis_isd Sync PPP                    -   Bundle: Vi2

!--- User travis_isdn is connected through two B-channels (Multilink PPP). !--- Interface Virtual-Access 2 (Vi2) controls the two B-channels.


maui-nas-02#show dialer map

!--- Observe the Dynamic Dialer Maps created for each dialin client.

Dynamic dialer map ip 172.22.60.2 name async_user () on As97
Dynamic dialer map ip 172.22.61.2 name austin_isdn () on Di10
Dynamic dialer map ip 172.22.61.3 name travis_isdn () on Di10

maui-nas-02#show users
  Line         User       Host(s)              Idle       Location
* 0 con 0                 idle                 00:00:00   
  97 tty 97    async_user Async interface      00:06:36   PPP: 172.22.60.2

!--- Async User. The IP address of the peer is indicated.


  Interface    User        Mode                Idle     Peer Address
  Vi1          austin_isd Virtual PPP (Bundle) 00:03:35 172.22.61.2
  Vi2          travis_isd Virtual PPP (Bundle) 00:00:20 172.22.61.3

!--- Virtual-Access Interface for the two multilink PPP users.

  Se0:1        austin_isd Sync PPP                    -   Bundle: Vi1
  Se0:2        austin_isd Sync PPP                    -   Bundle: Vi1

!--- User austin_isdn is connected through two B-channels(Multilink PPP). !--- Interface Virtual-Access 1 (Vi1) controls the two B-channels.

 Se0:3        travis_isd Sync PPP                    -   Bundle: Vi2
 Se0:4        travis_isd Sync PPP                    -   Bundle: Vi2


!--- User travis_isdn is connected through two B-channels (Multilink PPP). !--- Interface Virtual-Access 2 (Vi2) controls the two B-channels.


maui-nas-02#show dialer map

!--- Observe the Dynamic Dialer Maps created for each dialin client.

Dynamic dialer map ip 172.22.60.2 name async_user () on As97
Dynamic dialer map ip 172.22.61.2 name austin_isdn () on Di10
Dynamic dialer map ip 172.22.61.3 name travis_isdn () on Di10

maui-nas-02#show users
  Line         User       Host(s)              Idle       Location
* 0 con 0                 idle                 00:00:00
  97 tty 97    async_user Async interface      00:06:36   PPP: 172.22.60.2

!--- Async User. The IP address of the peer is indicated.


       Interface    User        Mode                Idle     Peer Address
       Vi1          austin_isd Virtual PPP (Bundle) 00:03:35 172.22.61.2
       Vi2          travis_isd Virtual PPP (Bundle) 00:00:20 172.22.61.3
     
!--- Virtual-Access Interface for the two multilink PPP users.

       Se0:1        austin_isd Sync PPP                    -   Bundle: Vi1
       Se0:2        austin_isd Sync PPP                    -   Bundle: Vi1
     
!--- User austin_isdn is connected through two B-channels(Multilink PPP). !--- Interface Virtual-Access 1 (Vi1) controls the two B-channels.

       Se0:3        travis_isd Sync PPP                    -   Bundle: Vi2
       Se0:4        travis_isd Sync PPP                    -   Bundle: Vi2
     
!--- User travis_isdn is connected through two B-channels (Multilink PPP). !--- Interface Virtual-Access 2 (Vi2) controls the two B-channels.


     maui-nas-02#show dialer map
     
!--- Observe the Dynamic Dialer Maps created for each dialin client.

     Dynamic dialer map ip 172.22.60.2 name async_user () on As97
     Dynamic dialer map ip 172.22.61.2 name austin_isdn () on Di10
     Dynamic dialer map ip 172.22.61.3 name travis_isdn () on Di10

아날로그 통화의 경우

maui-nas-02#show caller user async_user detail

       User: async_user, line tty 97, service Async
     
!--- Shows hardware-level settings for the user named async_user.

             Active time 00:00:34, Idle time 00:00:16
       Timeouts:            Absolute  Idle      Idle
                                      Session   Exec
           Limits:          -         -         00:10:00  
           Disconnect in:   -         -         -         
       TTY: Line 97, running PPP on As97
     
!--- The call is terminated on interface Async 97. !--- This interface is included in the Group-Async configuration.

       Location: PPP: 172.22.60.2
     
!--- IP address for the peer. This address is obtained from the IP pool "ASYNC".

       DS0: (slot/unit/channel)=0/0/2
     
!--- T1 channel on which the call arrived. !--- The call arrived on channel 0 in T1 0. 

       Line: Baud rate (TX/RX) is 115200/115200, no parity, 1 stopbits, 8 databits
       Status: Ready, Active, No Exit Banner, Async Interface Active
               HW PPP Support Active
       Capabilities: Hardware Flowcontrol In, Hardware Flowcontrol Out
                     Modem Callout, Modem RI is CD, 
                     Line usable as async interface, Integrated Modem
       Modem State: Ready

       User: async_user, line As97, service PPP
     
!--- PPP setting for the user named async_user. !--- Notice that the call is terminated on int Async97.

             Active time 00:00:32, Idle time 00:00:30
       Timeouts:            Absolute  Idle
           Limits:          -         00:15:00  
           Disconnect in:   -         00:14:28  
       PPP: LCP Open, multilink Closed, CHAP (<- AAA), IPCP
     
!--- LCP state is OPEN. If LCP state is not OPEN, !--- use debug ppp negotiation to isolate LCP issues.

       LCP: -> peer, ACCM, AuthProto, MagicNumber, PCompression, ACCompression
            <- peer, ACCM, MagicNumber, PCompression, ACCompression
       NCP: Open IPCP
     
!--- IPCP state is open. If IPCP state is not OPEN, !--- use debug ppp negotiation to isolate IPCP issues.

       IPCP: <- peer, Address
             -> peer, Address
       Dialer: Connected, inbound
               Idle timer 900 secs, idle 31 secs
               Type is IN-BAND ASYNC, group As97
       IP: Local 172.22.60.1, remote 172.22.60.2
     
!--- NAS IP address and the IP address assigned to the peer.

       Counts: 27 packets input, 1545 bytes, 0 no buffer
               1 input errors, 1 CRC, 0 frame, 0 overrun
               14 packets output, 347 bytes, 0 underruns
               0 output errors, 0 collisions, 0 interface resets
     
!--- Packets pass through the connection.

ISDN 통화의 경우

     maui-nas-02#show caller user austin_isdn detail 
     
!--- The user named austin_isdn has two PPP links, !--- and one virtual interface bundle.


       User: austin_isdn, line Se0:3, service PPP
     
!--- Shows PPP layer settings for the first channel !--- that belongs to the user named austin_isdn.

             Active time 00:04:01, Idle time 00:00:00
       Timeouts:            Absolute  Idle
           Limits:          -         -         
           Disconnect in:   -         -         
       PPP: LCP Open, multilink Open, CHAP (<- AAA)
     
!--- LCP state is OPEN. If LCP state is not OPEN, !--- use debug ppp negotiation to isolate LCP issues.

       LCP: -> peer, AuthProto, MagicNumber, MRRU, EndpointDisc
            <- peer, MagicNumber, MRRU, EndpointDisc
       Dialer: Connected, inbound
               Type is ISDN, group Di10
     
!--- Incoming call used rotary group of int Dialer 10.

       IP: Local 172.22.61.1
     
!--- IP address of the int Loopback 1. !--- Remember that int Dialer 1 was unnumbered to Loop 1. !--- The remote IP address is indicated under the virtual-interface.

       Bundle: Member of austin_isdn, last input 00:00:00
       Counts: 55 packets input, 1635 bytes, 0 no buffer
               0 input errors, 0 CRC, 0 frame, 0 overrun
               82 packets output, 3479 bytes, 0 underruns
               0 output errors, 0 collisions, 0 interface resets

       User: austin_isdn, line Se0:4, service PPP
     
!--- Shows PPP layer settings for the second channel !--- that belongs to the user named austin_isdn.

             Active time 00:03:59, Idle time 00:00:00
       Timeouts:            Absolute  Idle
           Limits:          -         -         
           Disconnect in:   -         -         
       PPP: LCP Open, multilink Open, CHAP (<- AAA)
       LCP: -> peer, AuthProto, MagicNumber, MRRU, EndpointDisc
            <- peer, MagicNumber, MRRU, EndpointDisc
       Dialer: Connected to , inbound
               Type is ISDN, group Di10
       IP: Local 172.22.61.1
       Bundle: Member of austin_isdn, last input 00:00:00
       Counts: 50 packets input, 1589 bytes, 0 no buffer
               0 input errors, 0 CRC, 0 frame, 0 overrun
               77 packets output, 3429 bytes, 0 underruns
               0 output errors, 0 collisions, 0 interface resets       

       User: austin_isdn, line Vi1, service PPP Bundle
     
!--- Shows Virtual-Access Interface Bundle that controls the connections.

             Active time 00:04:02, Idle time 00:04:01
       Timeouts:            Absolute  Idle
           Limits:          -         00:15:00  
           Disconnect in:   -         00:10:58  
       PPP: LCP Open, multilink Open, IPCP, CDPCP
       LCP: -> peer, MagicNumber, MRRU, EndpointDisc
            <- peer
       NCP: Open IPCP, CDPCP
     
!--- IPCP State is open. If IPCP state is not OPEN, !--- use debug ppp negotiation to isolate IPCP issues.

       IPCP: <- peer, Address
             -> peer, Address
       Dialer: Connected, inbound
               Idle timer 900 secs, idle 1 secs
               Type is IN-BAND SYNC, group Di10
       IP: Local 172.22.61.1, remote 172.22.61.2
     
!--- Dialer interface (Local) IP address !--- and the IP address assigned to the peer.

       Bundle: First link of austin_isdn, 2 links, last input 00:00:01
       Counts: 12 packets input, 1712 bytes, 0 no buffer
               0 input errors, 0 CRC, 0 frame, 0 overrun
               67 packets output, 5030 bytes, 0 underruns
               0 output errors, 0 collisions, 0 interface resets

문제 해결

이 섹션에서는 컨피그레이션 문제를 해결하는 데 사용할 수 있는 정보를 제공합니다.

문제 해결 리소스

필요에 따라 다음 리소스를 사용합니다.

수신 모뎀 통화 문제 해결 - 이 문서를 사용하여 아날로그 통화 오류를 해결합니다.
PRI Async Modem Callin(PRI 비동기 모뎀 호출) - 아날로그 통화 오류를 해결하기 위한 추가 정보에 이 문서를 사용합니다.
Incoming ISDN Call Troubleshooting(수신 ISDN 통화 문제 해결) - 이 문서를 사용하여 ISDN 통화 실패 문제를 해결합니다.
PRI ISDN Call(PRI ISDN 호출) - ISDN 통화 실패 문제를 해결하기 위한 추가 정보에 이 문서를 사용합니다.
T1 문제 해결 순서도 - T1 회로가 제대로 작동하지 않는다고 생각되면 이 순서도를 사용합니다.
T1/56K 회선에 대한 루프백 테스트 - 이 문서를 사용하여 라우터의 T1 포트가 올바르게 작동하는지 확인합니다.

문제 해결 명령

일부 show 명령은 출력 인터프리터 툴 에서 지원되는데(등록된 고객만), 이 툴을 사용하면 show 명령 출력의 분석 결과를 볼 수 있습니다.

참고: debug 명령을 실행하기 전에 디버그 명령에 대한 중요 정보를 참조하십시오.

debug dialer - 다이얼러 인터페이스에서 수신된 패킷에 대한 DDR 디버깅 정보를 표시합니다. 이 정보는 다이얼러 인터페이스를 사용하는 흥미로운 트래픽이 있는지 확인하는 데 도움이 될 수 있습니다.
debug isdn q931 - ISDN 네트워크 연결의 통화 설정 및 해제(레이어 3)를 표시합니다.
debug modem — 액세스 서버의 모뎀 회선 활동을 표시합니다. 모뎀 회선 상태가 변경되면 출력이 표시됩니다.
debug modem csm—내부 디지털 모뎀이 있는 라우터에서 CSM(Call Switching Module) 문제를 해결할 수 있습니다. 이 명령을 사용하면 수신 및 발신 통화 전환의 전체 시퀀스를 추적할 수 있습니다.
debug ppp negotiation—PPP 트래픽 및 교환에 대한 정보를 표시하고 LCP(Link Control Protocol), Authentication, NCP(Network Control Protocol)를 협상합니다. 성공적인 PPP 협상이 먼저 LCP 상태를 연 다음 NCP를 인증하고 마지막으로 협상합니다. LCP 협상 중에 MRRU(Maximum Receive Reguided Unit)와 같은 멀티링크 매개변수가 설정됩니다.
debug ppp authentication—CHAP 패킷 교환 및 PAP(Password Authentication Protocol) 교환을 비롯한 PPP 인증 프로토콜 메시지를 표시합니다.
debug ppp error—PPP 연결 협상 및 작업과 관련된 프로토콜 오류 및 오류 통계를 표시합니다.

디버그 출력 샘플

다음은 성공한 통화에 대한 디버그 출력입니다. 굵게 표시된 섹션과 출력에 제공된 코멘트를 확인합니다. 가져온 출력을 여기에 표시된 결과와 비교합니다.

아날로그 통화의 경우

maui-nas-02#debug isdn q931
     ISDN Q931 packets debugging is on
     maui-nas-02#debug modem
     Modem control/process activation debugging is on
     maui-nas-02#debug modem csm
     Modem Management Call Switching Module debugging is on
     maui-nas-02#debug ppp negotiation
     PPP protocol negotiation debugging is on
     maui-nas-02#debug ppp authentication
     PPP authentication debugging is on

     maui-nas-02#
     Sep 28 13:13:28.369: ISDN Se0:23: RX <-  SETUP pd = 8  callref = 0x5285

     
!--- Incoming Q.931 SETUP message. This indicates an incoming call. !--- For more information on Q.931 refer to !--- Troubleshooting ISDN BRI Layer 3 using the debug isdn q931 Command.

     Sep 28 13:13:28.369:   Bearer Capability i = 0x9090A2
     Sep 28 13:13:28.369:   Channel ID i = 0xA18383
     Sep 28 13:13:28.369:   Progress Ind i = 0x8183 - Origination address is non-ISDN 
     Sep 28 13:13:28.369:   Called Party Number i = 0xA1, '81560', Plan:ISDN, Type:National
     Sep 28 13:13:28.373: VDEV_ALLOCATE: 2/0 is allocated
     
!--- The Call Switch Module (CSM) is informed about the call. !--- The CSM allocates modem 2/0 to the incoming call.

     Sep 28 13:13:28.373: EVENT_FROM_ISDN::dchan_idb=0x618569F4, call_id=0x28, 
     ces=0x0 bchan=0x2, event=0x1, cause=0x0
     Sep 28 13:13:28.373:  dev in call to isdn : set dnis_collected & fap_notify
     Sep 28 13:13:28.373: EVENT_FROM_ISDN:(0028): DEV_INCALL at slot 2 and port 0
     Sep 28 13:13:28.373:  EVENT_FROM_ISDN: decode:calling 0ct3 0x0, called oct3 
     0xA1, oct3a 0x0,mask 0x3C
     Sep 28 13:13:28.373:  EVENT_FROM_ISDN: csm_call_info:calling 0ct3 0x0, 
     called oct3 0xA1, oct3a 0x0,mask 0x3C
     Sep 28 13:13:28.377: CSM_PROC_IDLE: CSM_EVENT_ISDN_CALL at slot 2, port 0
     Sep 28 13:13:28.377: Mica Modem(2/0): Configure(0x1 = 0x0) 
     Sep 28 13:13:28.377: Mica Modem(2/0): Configure(0x23 = 0x0) 
     Sep 28 13:13:28.377: Mica Modem(2/0): Call Setup
     
!--- CSM sends the Call Setup Message to Modem 2/0. !--- The modem must now go off-hook.

     Sep 28 13:13:28.377: csm_connect_pri_vdev: TS allocated at bp_stream 0, 
     bp_Ch 0,vdev_common 0x6141BB68
     Sep 28 13:13:28.377: ISDN Se0:23: TX ->  CALL_PROC pd = 8  callref = 0xD285
     Sep 28 13:13:28.377:         Channel ID i = 0xA98383
     
!--- The Call Proceeding Message is sent through the D-channel.

     Sep 28 13:13:28.377: ISDN Se0:23: TX ->  ALERTING pd = 8  callref = 0xD285
     Sep 28 13:13:28.445: Mica Modem(2/0): State Transition to Call Setup
     
!--- Modem transitions to state Call Setup. !--- For more information on MICA Modem States refer to MICA Modem States.

     Sep 28 13:13:28.445: Mica Modem(2/0): Went offhook
     
!--- Modem informs the CSM that it went offhook.

     Sep 28 13:13:28.445: CSM_PROC_IC2_RING: CSM_EVENT_MODEM_OFFHOOK at slot 2, port 0
     Sep 28 13:13:28.445: ISDN Se0:23: TX ->  CONNECT pd = 8  callref = 0xD285
     
!--- D-channel transmits a CONNECT.

     Sep 28 13:13:28.461: ISDN Se0:23: RX <-  CONNECT_ACK pd = 8  callref = 0x5285
     
!--- The Q.931 CONNECT_ACK message is received.

     Sep 28 13:13:28.461: ISDN Se0:23: CALL_PROGRESS: CALL_CONNECTED call id 0x28, 
     bchan 2, dsl 0
     Sep 28 13:13:28.461: EVENT_FROM_ISDN::dchan_idb=0x618569F4, call_id=0x28, 
     ces=0x0 bchan=0x2, event=0x4, cause=0x0
     Sep 28 13:13:28.461: EVENT_FROM_ISDN:(0028): DEV_CONNECTED at slot 2 and port 0
     Sep 28 13:13:28.461: CSM_PROC_IC6_WAIT_FOR_CONNECT: 
     CSM_EVENT_ISDN_CONNECTED at slot 2, port 0
     Sep 28 13:13:28.465: Mica Modem(2/0): Link Initiate
     
!--- When the Q.931 CONNECT_ACK message is received, the Link initiate message !--- is sent to the MICA modem, and negotiation with remote modem occurs.

     Sep 28 13:13:28.465: %ISDN-6-CONNECT: Interface Serial0:2 is now connected to N/A N/A
     Sep 28 13:13:29.557: Mica Modem(2/0): State Transition to Connect
     
!--- Modem moves to the Connect state.

     Sep 28 13:13:34.073: Mica Modem(2/0): State Transition to Link
     Sep 28 13:13:45.478: Mica Modem(2/0): State Transition to Trainup
     Sep 28 13:13:53.642: Mica Modem(2/0): State Transition to EC Negotiating
     Sep 28 13:13:54.122: Mica Modem(2/0): State Transition to Steady State
     
!--- Modem tranistions to the Steady state.

     Sep 28 13:13:54.266: TTY97: DSR came up
     
!--- Indicates that the modem trainup is complete.

     Sep 28 13:13:54.266: tty97: Modem: IDLE->(unknown)
     Sep 28 13:13:54.266: TTY97: EXEC creation
     Sep 28 13:13:54.266: TTY97: set timer type 10, 30 seconds
     Sep 28 13:13:57.202: TTY97: Autoselect(2) sample 7E
     Sep 28 13:13:57.202: TTY97: Autoselect(2) sample 7EFF
     Sep 28 13:13:57.202: TTY97: Autoselect(2) sample 7EFF7D
     Sep 28 13:13:57.202: TTY97: Autoselect(2) sample 7EFF7D23
     Sep 28 13:13:57.202: TTY97 Autoselect cmd:  ppp negotiate
     
!--- The router detects PPP packets and automatically launches PPP.

     Sep 28 13:13:57.206: TTY97: EXEC creation
     Sep 28 13:13:57.206: TTY97: create timer type 1, 600 seconds
     Sep 28 13:13:57.334: TTY97: destroy timer type 1
     Sep 28 13:13:57.334: TTY97: no timer type 0 to destroy
     Sep 28 13:13:57.334: As97 IPCP: Install route to 172.22.60.2
     Sep 28 13:13:59.334: %LINK-3-UPDOWN: Interface Async97, changed state to up
     Sep 28 13:13:59.334: As97 PPP: Treating connection as a callin
     Sep 28 13:13:59.334: As97 PPP: Phase is ESTABLISHING, Passive Open [0 sess, 0 load]
     Sep 28 13:13:59.334: As97 LCP: State is Listen
     
!--- LCP negotiation begins.

     Sep 28 13:14:00.214: As97 LCP: I CONFREQ [Listen] id 3 len 23
     
!--- Incoming LCP CONFREQ. !--- For more information on how to interpret PPP debugs, refer to !--- Dialup Technology: Troubleshooting Techniques.

     Sep 28 13:14:00.214: As97 LCP:    ACCM 0x000A0000 (0x0206000A0000)
     Sep 28 13:14:00.214: As97 LCP:    MagicNumber 0x0F7CD34A (0x05060F7CD34A)
     Sep 28 13:14:00.214: As97 LCP:    PFC (0x0702)
     Sep 28 13:14:00.214: As97 LCP:    ACFC (0x0802)
     Sep 28 13:14:00.214: As97 LCP:    Callback 6  (0x0D0306)
     Sep 28 13:14:00.214: Unthrottle 97
     Sep 28 13:14:00.214: As97 LCP: O CONFREQ [Listen] id 1 len 43
     Sep 28 13:14:00.214: As97 LCP:    ACCM 0x000A0000 (0x0206000A0000)
     Sep 28 13:14:00.214: As97 LCP:    AuthProto CHAP (0x0305C22305)
     Sep 28 13:14:00.214: As97 LCP:    MagicNumber 0x3090DE31 (0x05063090DE31)
     Sep 28 13:14:00.214: As97 LCP:    PFC (0x0702)
     Sep 28 13:14:00.214: As97 LCP:    ACFC (0x0802)
     Sep 28 13:14:00.214: As97 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:14:00.214: As97 LCP:    EndpointDisc 1 Local (
     0x130E016D6175692D6E61732D3032)
     Sep 28 13:14:00.214: As97 LCP: O CONFREJ [Listen] id 3 len 7
     Sep 28 13:14:00.214: As97 LCP:    Callback 6  (0x0D0306)
     Sep 28 13:14:00.342: As97 LCP: I CONFREQ [REQsent] id 4 len 20
     Sep 28 13:14:00.342: As97 LCP:    ACCM 0x000A0000 (0x0206000A0000)
     Sep 28 13:14:00.342: As97 LCP:    MagicNumber 0x0F7CD34A (0x05060F7CD34A)
     Sep 28 13:14:00.342: As97 LCP:    PFC (0x0702)
     Sep 28 13:14:00.342: As97 LCP:    ACFC (0x0802)
     Sep 28 13:14:00.342: As97 LCP: O CONFACK [REQsent] id 4 len 20
     Sep 28 13:14:00.342: As97 LCP:    ACCM 0x000A0000 (0x0206000A0000)
     Sep 28 13:14:00.342: As97 LCP:    MagicNumber 0x0F7CD34A (0x05060F7CD34A)
     Sep 28 13:14:00.342: As97 LCP:    PFC (0x0702)
     Sep 28 13:14:00.342: As97 LCP:    ACFC (0x0802)
     Sep 28 13:14:02.214: As97 LCP: TIMEout: State ACKsent
     Sep 28 13:14:02.214: As97 LCP: O CONFREQ [ACKsent] id 2 len 43
     Sep 28 13:14:02.214: As97 LCP:    ACCM 0x000A0000 (0x0206000A0000)
     Sep 28 13:14:02.214: As97 LCP:    AuthProto CHAP (0x0305C22305)
     Sep 28 13:14:02.214: As97 LCP:    MagicNumber 0x3090DE31 (0x05063090DE31)
     Sep 28 13:14:02.214: As97 LCP:    PFC (0x0702)
     Sep 28 13:14:02.214: As97 LCP:    ACFC (0x0802)
     Sep 28 13:14:02.214: As97 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:14:02.214: As97 LCP:    EndpointDisc 1 Local 
     (0x130E016D6175692D6E61732D3032)
     Sep 28 13:14:02.326: As97 LCP: I CONFREJ [ACKsent] id 2 len 22
     Sep 28 13:14:02.326: As97 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:14:02.326: As97 LCP:    EndpointDisc 1 Local 
     (0x130E016D6175692D6E61732D3032)
     Sep 28 13:14:02.326: As97 LCP: O CONFREQ [ACKsent] id 3 len 25
     Sep 28 13:14:02.326: As97 LCP:    ACCM 0x000A0000 (0x0206000A0000)
     Sep 28 13:14:02.326: As97 LCP:    AuthProto CHAP (0x0305C22305)
     Sep 28 13:14:02.326: As97 LCP:    MagicNumber 0x3090DE31 (0x05063090DE31)
     Sep 28 13:14:02.326: As97 LCP:    PFC (0x0702)
     Sep 28 13:14:02.326: As97 LCP:    ACFC (0x0802)
     Sep 28 13:14:02.518: As97 LCP: I CONFACK [ACKsent] id 3 len 25
     Sep 28 13:14:02.518: As97 LCP:    ACCM 0x000A0000 (0x0206000A0000)
     Sep 28 13:14:02.518: As97 LCP:    AuthProto CHAP (0x0305C22305)
     Sep 28 13:14:02.518: As97 LCP:    MagicNumber 0x3090DE31 (0x05063090DE31)
     Sep 28 13:14:02.518: As97 LCP:    PFC (0x0702)
     Sep 28 13:14:02.518: As97 LCP:    ACFC (0x0802)
     Sep 28 13:14:02.518: As97 LCP: State is Open
     
!--- LCP negotiation is complete.

     Sep 28 13:14:02.518: As97 PPP: Phase is AUTHENTICATING, 
     by this end [0 sess, 0 load]
     Sep 28 13:14:02.518: As97 CHAP: O CHALLENGE id 1 len 32 from "maui-nas-02"
     Sep 28 13:14:02.646: As97 CHAP: I RESPONSE id 1 len 31 from "async_user"
     Sep 28 13:14:02.646: As97 AUTH: Started process 0 pid 34
     Sep 28 13:14:02.650: As97 CHAP: O SUCCESS id 1 len 4
     
!--- CHAP authentication is successful. !--- If authentication fails, check the username and password. !--- Refer to Dialup Technology: Troubleshooting Techniques 
.
     Sep 28 13:14:02.650: As97 PPP: Phase is UP [0 sess, 0 load]
     Sep 28 13:14:02.650: As97 IPCP: O CONFREQ [Closed] id 1 len 10
     
!--- IPCP negotiation begins.

     Sep 28 13:14:02.650: As97 IPCP:    Address 172.22.60.1 (0x0306AC163C01)
     Sep 28 13:14:02.758: As97 IPCP: I CONFREQ [REQsent] id 1 len 40
     Sep 28 13:14:02.758: As97 IPCP:    CompressType VJ 15 slots CompressSlotID 
     (0x0206002D0F01)
     Sep 28 13:14:02.758: As97 IPCP:    Address 0.0.0.0 (0x030600000000)
     Sep 28 13:14:02.758: As97 IPCP:    PrimaryDNS 172.22.53.210 (0x8106AC1635D2)
     Sep 28 13:14:02.758: As97 IPCP:    PrimaryWINS 0.0.0.0 (0x820600000000)
     Sep 28 13:14:02.758: As97 IPCP:    SecondaryDNS 0.0.0.0 (0x830600000000)
     Sep 28 13:14:02.758: As97 IPCP:    SecondaryWINS 0.0.0.0 (0x840600000000)
     Sep 28 13:14:02.758: As97 AAA/AUTHOR/IPCP: Start.  
     Her address 0.0.0.0, we want 172.22.60.2
     Sep 28 13:14:02.758: As97 AAA/AUTHOR/IPCP: Done.  
     Her address 0.0.0.0, we want 172.22.60.2
     
!--- Address is obtained from the Address Pool named "Async".

     Sep 28 13:14:02.758: As97 IPCP: O CONFREJ [REQsent] id 1 len 28
     Sep 28 13:14:02.758: As97 IPCP:    CompressType VJ 15 slots CompressSlotID 
     (0x0206002D0F01)
     Sep 28 13:14:02.758: As97 IPCP:    PrimaryWINS 0.0.0.0 (0x820600000000)
     Sep 28 13:14:02.758: As97 IPCP:    SecondaryDNS 0.0.0.0 (0x830600000000)
     Sep 28 13:14:02.758: As97 IPCP:    SecondaryWINS 0.0.0.0 (0x840600000000)
     Sep 28 13:14:02.802: As97 CCP: I CONFREQ [Not negotiated] id 1 len 15
     Sep 28 13:14:02.802: As97 CCP:    MS-PPC supported bits 0x00000001 
     (0x120600000001)
     Sep 28 13:14:02.802: As97 CCP:    Stacker history 1 check mode EXTENDED 
     (0x1105000104)
     Sep 28 13:14:02.802: As97 LCP: O PROTREJ [Open] id 4 len 21 protocol CCP
     Sep 28 13:14:02.802: As97 LCP:  (0x80FD0101000F12060000000111050001)
     Sep 28 13:14:02.802: As97 LCP:  (0x04)
     Sep 28 13:14:02.802: As97 IPCP: I CONFACK [REQsent] id 1 len 10
     Sep 28 13:14:02.802: As97 IPCP:    Address 172.22.60.1 (0x0306AC163C01)
     Sep 28 13:14:04.650: As97 IPCP: TIMEout: State ACKrcvd
     Sep 28 13:14:04.650: As97 IPCP: O CONFREQ [ACKrcvd] id 2 len 10
     Sep 28 13:14:04.650: As97 IPCP:    Address 172.22.60.1 (0x0306AC163C01)
     Sep 28 13:14:04.758: As97 IPCP: I CONFACK [REQsent] id 2 len 10
     Sep 28 13:14:04.758: As97 IPCP:    Address 172.22.60.1 (0x0306AC163C01)
     Sep 28 13:14:05.750: As97 IPCP: I CONFREQ [ACKrcvd] id 2 len 34
     Sep 28 13:14:05.750: As97 IPCP:    Address 0.0.0.0 (0x030600000000)
     Sep 28 13:14:05.750: As97 IPCP:    PrimaryDNS 172.22.53.210 (0x8106AC1635D2)
     Sep 28 13:14:05.750: As97 IPCP:    PrimaryWINS 0.0.0.0 (0x820600000000)
     Sep 28 13:14:05.750: As97 IPCP:    SecondaryDNS 0.0.0.0 (0x830600000000)
     Sep 28 13:14:05.750: As97 IPCP:    SecondaryWINS 0.0.0.0 (0x840600000000)
     Sep 28 13:14:05.750: As97 AAA/AUTHOR/IPCP: Start.  
     Her address 0.0.0.0, we want 172.22.60.2
     Sep 28 13:14:05.750: As97 AAA/AUTHOR/IPCP: Done.  
     Her address 0.0.0.0, we want 172.22.60.2
     Sep 28 13:14:05.750: As97 IPCP: O CONFREJ [ACKrcvd] id 2 len 22
     Sep 28 13:14:05.750: As97 IPCP:    PrimaryWINS 0.0.0.0 (0x820600000000)
     Sep 28 13:14:05.754: As97 IPCP:    SecondaryDNS 0.0.0.0 (0x830600000000)
     Sep 28 13:14:05.754: As97 IPCP:    SecondaryWINS 0.0.0.0 (0x840600000000)
     Sep 28 13:14:05.878: As97 IPCP: I CONFREQ [ACKrcvd] id 3 len 16
     Sep 28 13:14:05.878: As97 IPCP:    Address 0.0.0.0 (0x030600000000)
     Sep 28 13:14:05.878: As97 IPCP:    PrimaryDNS 172.22.53.210 (0x8106AC1635D2)
     Sep 28 13:14:05.878: As97 AAA/AUTHOR/IPCP: Start.  
     Her address 0.0.0.0, we want 172.22.60.2
     Sep 28 13:14:05.878: As97 AAA/AUTHOR/IPCP: Done.  
     Her address 0.0.0.0, we want 172.22.60.2
     Sep 28 13:14:05.878: As97 IPCP: O CONFNAK [ACKrcvd] id 3 len 10
     Sep 28 13:14:05.878: As97 IPCP:    Address 172.22.60.2 (0x0306AC163C02)
     Sep 28 13:14:05.990: As97 IPCP: I CONFREQ [ACKrcvd] id 4 len 16
     Sep 28 13:14:05.990: As97 IPCP:    Address 172.22.60.2 (0x0306AC163C02)
     Sep 28 13:14:05.990: As97 IPCP:    PrimaryDNS 172.22.53.210 (0x8106AC1635D2)
     Sep 28 13:14:05.990: As97 AAA/AUTHOR/IPCP: Start.  
     Her address 172.22.60.2, we want 172.22.60.2
     Sep 28 13:14:05.990: As97 AAA/AUTHOR/IPCP: Reject 172.22.60.2, using 172.22.60.2
     Sep 28 13:14:05.990: As97 AAA/AUTHOR/IPCP: Done.  
     Her address 172.22.60.2, we want 172.22.60.2
     Sep 28 13:14:05.994: As97 IPCP: O CONFACK [ACKrcvd] id 4 len 16
     Sep 28 13:14:05.994: As97 IPCP:    Address 172.22.60.2 (0x0306AC163C02)
     Sep 28 13:14:05.994: As97 IPCP:    PrimaryDNS 172.22.53.210 (0x8106AC1635D2)
     Sep 28 13:14:05.994: As97 IPCP: State is Open
     
!--- IPCP negotiation is complete. The user is now connected.

ISDN 통화의 경우

maui-nas-02#debug isdn q931
     ISDN Q931 packets debugging is on
     maui-nas-02#debug ppp negotiation
     PPP protocol negotiation debugging is on
     maui-nas-02#debug ppp authentication
     PPP authentication debugging is on

     Sep 28 13:25:02.630: ISDN Se0:23: RX <-  SETUP pd = 8  callref = 0x5346
     
!--- Incoming Q.931 Setup message.

     Sep 28 13:25:02.630:         Bearer Capability i = 0x8890218F
     Sep 28 13:25:02.630:         Channel ID i = 0xA18384
     Sep 28 13:25:02.630:         Called Party Number i = 0xA1, '81560', 
     Plan:ISDN, Type:National
     Sep 28 13:25:02.634: %LINK-3-UPDOWN: Interface Serial0:3, changed state to up
     Sep 28 13:25:02.638: Se0:3 PPP: Treating connection as a callin
     Sep 28 13:25:02.638: Se0:3 PPP: Phase is ESTABLISHING, 
     Passive Open [0 sess, 1 load]
     Sep 28 13:25:02.638: Se0:3 LCP: State is Listen
     Sep 28 13:25:02.638: ISDN Se0:23: TX ->  CALL_PROC pd = 8  callref = 0xD346
     Sep 28 13:25:02.638:         Channel ID i = 0xA98384
     Sep 28 13:25:02.638: ISDN Se0:23: TX ->  CONNECT pd = 8  callref = 0xD346
     Sep 28 13:25:02.638:         Channel ID i = 0xA98384
     Sep 28 13:25:02.658: ISDN Se0:23: RX <-  CONNECT_ACK pd = 8  callref = 0x5346

     Sep 28 13:25:02.658: ISDN Se0:23: CALL_PROGRESS: 
     CALL_CONNECTED call id 0x2B, bchan 3, dsl 0
     
!--- Call is connected.

     Sep 28 13:25:02.886: Se0:3 LCP: I CONFREQ [Listen] id 61 len 28
     Sep 28 13:25:02.886: Se0:3 LCP:    MagicNumber 0x1EB88B1C (0x05061EB88B1C)
     Sep 28 13:25:02.886: Se0:3 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:25:02.886: Se0:3 LCP:    EndpointDisc 1 Local 
     (0x130E0161757374696E5F6973646E)
     Sep 28 13:25:02.886: Se0:3 LCP: O CONFREQ [Listen] id 1 len 33
     Sep 28 13:25:02.886: Se0:3 LCP:    AuthProto CHAP (0x0305C22305)
     Sep 28 13:25:02.886: Se0:3 LCP:    MagicNumber 0x309AFABD (0x0506309AFABD)
     Sep 28 13:25:02.886: Se0:3 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:25:02.886: Se0:3 LCP:    EndpointDisc 1 Local 
     (0x130E016D6175692D6E61732D3032)
     Sep 28 13:25:02.886: Se0:3 LCP: O CONFACK [Listen] id 61 len 28
     Sep 28 13:25:02.886: Se0:3 LCP:    MagicNumber 0x1EB88B1C (0x05061EB88B1C)
     Sep 28 13:25:02.886: Se0:3 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:25:02.886: Se0:3 LCP:    EndpointDisc 1 Local 
     (0x130E0161757374696E5F6973646E)
     Sep 28 13:25:02.922: Se0:3 LCP: I CONFACK [ACKsent] id 1 len 33
     Sep 28 13:25:02.922: Se0:3 LCP:    AuthProto CHAP (0x0305C22305)
     Sep 28 13:25:02.922: Se0:3 LCP:    MagicNumber 0x309AFABD (0x0506309AFABD)
     Sep 28 13:25:02.922: Se0:3 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:25:02.922: Se0:3 LCP:    EndpointDisc 1 Local 
     (0x130E016D6175692D6E61732D3032)
     Sep 28 13:25:02.922: Se0:3 LCP: State is Open
     
!--- LCP negotiation is complete.

     Sep 28 13:25:02.922: Se0:3 PPP: 
     Phase is AUTHENTICATING, by this end [0 sess, 1 load]
     Sep 28 13:25:02.922: Se0:3 CHAP: O CHALLENGE id 1 len 32 from "maui-nas-02"
     Sep 28 13:25:02.954: Se0:3 CHAP: I RESPONSE id 1 len 32 from "austin_isdn"
     Sep 28 13:25:02.954: Se0:3 CHAP: O SUCCESS id 1 len 4
     
!--- PPP CHAP authentication is successful.

     Sep 28 13:25:02.958: Se0:3 PPP: Phase is VIRTUALIZED [0 sess, 1 load]
     Sep 28 13:25:02.958: Vi1 PPP: Phase is DOWN, Setup [0 sess, 1 load]
     Sep 28 13:25:02.982: Vi1 PPP: Phase is DOWN, Setup [0 sess, 1 load]
     Sep 28 13:25:02.982: Se0:3 IPCP: 
     Packet buffered while building MLP bundle interface
     Sep 28 13:25:02.986: %LINK-3-UPDOWN: Interface Virtual-Access1, 
     changed state to up
     
!--- Virtual-Access Interface is up. !--- This interface controls the incoming call.

     Sep 28 13:25:02.986: Vi1 PPP: Treating connection as a callin
     Sep 28 13:25:02.986: Vi1 PPP: Phase is ESTABLISHING, Passive Open [0 sess, 1 load]
     Sep 28 13:25:02.986: Vi1 LCP: State is Listen
     Sep 28 13:25:02.986: Vi1 PPP: Phase is UP [0 sess, 1 load]
     Sep 28 13:25:02.986: Vi1 IPCP: O CONFREQ [Closed] id 1 len 10
     Sep 28 13:25:02.986: Vi1 IPCP:    Address 172.22.61.1 (0x0306AC163D01)
     Sep 28 13:25:02.990: Vi1 MLP: Added first link Se0:3 to bundle austin_isdn
     Sep 28 13:25:02.990: Vi1 PPP: Pending ncpQ size is 1
     Sep 28 13:25:02.990: Se0:3 IPCP: Redirect packet to Vi1
     Sep 28 13:25:02.990: Vi1 IPCP: I CONFREQ [REQsent] id 45 len 10
     Sep 28 13:25:02.990: Vi1 IPCP:    Address 10.0.0.1 (0x03060A000001)
     Sep 28 13:25:02.990: Vi1 AAA/AUTHOR/IPCP: Start.  
     Her address 10.0.0.1, we want 0.0.0.0
     Sep 28 13:25:02.990: Vi1 AAA/AUTHOR/IPCP: Reject 10.0.0.1, using 0.0.0.0
     Sep 28 13:25:02.990: Vi1 AAA/AUTHOR/IPCP: Done.  
     Her address 10.0.0.1, we want 0.0.0.0
     Sep 28 13:25:02.990: Vi1 IPCP: O CONFNAK [REQsent] id 45 len 10
     Sep 28 13:25:02.990: Vi1 IPCP:    Address 172.22.61.2 (0x0306AC163D02)
     
!--- Peer IP address is assigned from IP Pool named "ISDN".

     Sep 28 13:25:02.990: Se0:3 CDPCP: MLP bundle interface is built, 
     process packets now 
     Sep 28 13:25:02.990: Se0:3 CDPCP: Redirect packet to Vi1
     Sep 28 13:25:02.990: Vi1 CDPCP: I CONFREQ [Not negotiated] id 23 len 4
     Sep 28 13:25:02.990: Vi1 LCP: O PROTREJ [Open] id 1 len 10 protocol CDPCP 
     (0x820701170004)
     Sep 28 13:25:03.010: Vi1 IPCP: I CONFACK [REQsent] id 1 len 10
     Sep 28 13:25:03.010: Vi1 IPCP:    Address 172.22.61.1 (0x0306AC163D01)
     Sep 28 13:25:03.010: Vi1 IPCP: I CONFREQ [ACKrcvd] id 46 len 4
     Sep 28 13:25:03.010: Vi1 IPCP: O CONFACK [ACKrcvd] id 46 len 4
     Sep 28 13:25:03.010: Vi1 IPCP: State is Open
     
!--- IPCP negotiation is complete. The call is now connected.

     Sep 28 13:25:03.014: Di10 IPCP: Install route to 172.22.61.2
     Sep 28 13:25:03.958: %LINEPROTO-5-UPDOWN: 
     Line protocol on Interface Serial0:3, changed state to up
     Sep 28 13:25:03.986: %LINEPROTO-5-UPDOWN: 
     Line protocol on Interface Virtual-Access1, changed state to up
     Sep 28 13:25:04.146: ISDN Se0:23: RX <-  SETUP pd = 8  callref = 0x5409
     
!--- The second link in the multilink connection arrives.

     Sep 28 13:25:04.150:         Bearer Capability i = 0x8890218F
     Sep 28 13:25:04.150:         Channel ID i = 0xA18385
     Sep 28 13:25:04.150:         Called Party Number i = 0xA1, '81560', Plan:ISDN, 
     Type:National
     Sep 28 13:25:04.154: %LINK-3-UPDOWN: Interface Serial0:4, changed state to up
     Sep 28 13:25:04.154: %ISDN-6-CONNECT: Interface Serial0:3 is now connected to  
     austin_isdn
     Sep 28 13:25:04.154: Se0:4 PPP: Treating connection as a callin
     Sep 28 13:25:04.154: Se0:4 PPP: Phase is ESTABLISHING, 
     Passive Open [0 sess, 1 load]
     Sep 28 13:25:04.154: Se0:4 LCP: State is Listen
     Sep 28 13:25:04.158: ISDN Se0:23: TX ->  CALL_PROC pd = 8  callref = 0xD409
     Sep 28 13:25:04.158:         Channel ID i = 0xA98385
     Sep 28 13:25:04.158: ISDN Se0:23: TX ->  CONNECT pd = 8  callref = 0xD409
     Sep 28 13:25:04.158:         Channel ID i = 0xA98385
     Sep 28 13:25:04.178: ISDN Se0:23: RX <-  CONNECT_ACK pd = 8  callref = 0x5409

     Sep 28 13:25:04.178: ISDN Se0:23: CALL_PROGRESS: 
     CALL_CONNECTED call id 0x2C, bchan 4, dsl 0
     Sep 28 13:25:04.394: Se0:4 LCP: I CONFREQ [Listen] id 51 len 28
     Sep 28 13:25:04.394: Se0:4 LCP:    MagicNumber 0x1EB8910D (0x05061EB8910D)
     Sep 28 13:25:04.394: Se0:4 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:25:04.394: Se0:4 LCP:    EndpointDisc 1 Local 
     (0x130E0161757374696E5F6973646E)
     Sep 28 13:25:04.394: Se0:4 LCP: O CONFREQ [Listen] id 1 len 33
     Sep 28 13:25:04.394: Se0:4 LCP:    AuthProto CHAP (0x0305C22305)
     Sep 28 13:25:04.394: Se0:4 LCP:    MagicNumber 0x309B00A6 (0x0506309B00A6)
     Sep 28 13:25:04.394: Se0:4 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:25:04.394: Se0:4 LCP:    EndpointDisc 1 Local 
     (0x130E016D6175692D6E61732D3032)
     Sep 28 13:25:04.394: Se0:4 LCP: O CONFACK [Listen] id 51 len 28
     Sep 28 13:25:04.394: Se0:4 LCP:    MagicNumber 0x1EB8910D (0x05061EB8910D)
     Sep 28 13:25:04.394: Se0:4 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:25:04.394: Se0:4 LCP:    EndpointDisc 1 Local 
     (0x130E0161757374696E5F6973646E)
     Sep 28 13:25:04.430: Se0:4 LCP: I CONFACK [ACKsent] id 1 len 33
     Sep 28 13:25:04.430: Se0:4 LCP:    AuthProto CHAP (0x0305C22305)
     Sep 28 13:25:04.430: Se0:4 LCP:    MagicNumber 0x309B00A6 (0x0506309B00A6)
     Sep 28 13:25:04.430: Se0:4 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:25:04.430: Se0:4 LCP:    EndpointDisc 1 Local 
     (0x130E016D6175692D6E61732D3032)
     Sep 28 13:25:04.430: Se0:4 LCP: State is Open
     Sep 28 13:25:04.430: Se0:4 PPP: Phase is AUTHENTICATING, 
     by this end [0 sess, 1 load]
     Sep 28 13:25:04.430: Se0:4 CHAP: O CHALLENGE id 1 len 32 from "maui-nas-02"
     Sep 28 13:25:04.462: Se0:4 CHAP: I RESPONSE id 1 len 32 from "austin_isdn"
     Sep 28 13:25:04.466: Se0:4 CHAP: O SUCCESS id 1 len 4
     Sep 28 13:25:04.466: Se0:4 PPP: Phase is VIRTUALIZED [0 sess, 1 load]
     Sep 28 13:25:04.466: Vi1 MLP: Added link Se0:4 to bundle austin_isdn
     
!--- An additional Link is now added to exiting Virtual Interface Bundle.

     Sep 28 13:25:05.466: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0:4, 
     changed state to up
     Sep 28 13:25:10.154: %ISDN-6-CONNECT: 
     Interface Serial0:4 is now connected to austin_isdn
     
!--- The second call is connected. The multilink Bundle is complete. 

     maui-nas-02#

수신 멀티링크 비동기 및 ISDN 통화에 대해 PRI를 사용하여 액세스 서버 구성

다운로드 옵션

편견 없는 언어

이 번역에 관하여

목차

소개

사전 요구 사항

요구 사항

사용되는 구성 요소

관련 제품

표기 규칙

구성

네트워크 다이어그램

구성

다음을 확인합니다.

샘플 show 출력

일반 보기

아날로그 통화의 경우

ISDN 통화의 경우

문제 해결

문제 해결 리소스

문제 해결 명령

디버그 출력 샘플

아날로그 통화의 경우

ISDN 통화의 경우

관련 정보

개정 이력

이 문서가 도움이 되셨습니까?

지원 문의

이 문서가 적용되는 제품