SDA 캠퍼스 패브릭 환경의 ASM(Any-Source Multicast) 개요
목차
소개
이 문서에서는 SD-Access(Software-Defined Access) 환경에서 RP(Single Rendezvous Point)를 사용하는 ASM(Any-Source Multicast)의 개요를 설명합니다.
사전 요구 사항
요구 사항
LISP(Locator ID Separation Protocol) 및 멀티캐스트에 대한 지식이 있는 것이 좋습니다.
사용되는 구성 요소
이 문서는 특정 소프트웨어 및 하드웨어 버전으로 한정되지 않습니다.
이 문서의 정보는 특정 랩 환경의 디바이스를 토대로 작성되었습니다. 네트워크가 가동 중인 경우 모든 명령의 잠재적인 영향을 이해해야 합니다.GUI
이 문서에 사용된 장치
DNAC(Digital Network Architecture Controller) - 버전 1.2.1
에지 및 경계 - Cat3k Cisco 스위치
Fusion - VRF(Virtual Route Forwarding) 간 누설을 지원하는 Cisco 라우터
구성
네트워크 다이어그램
이 문서에 사용되는 토폴로지는 외부 테두리로 본딩된 두 개의 보더 라우터와 각 보더 라우터에 연결된 두 개의 Fusion 라우터로 구성됩니다. Border-1은 RP로 구성되고 Multicast Source는 Fusion-2에 연결되며 Multicast Receiver는 Edge-1에 연결됩니다.
설정
이 문서에서는 SDA(Software-Defined Access) 환경에서 패브릭을 구성하는 단계를 다루지 않으며 특정 VN에 대해 패브릭 도메인에서 멀티캐스트를 구성하는 단계에 대한 설명으로 시작합니다.
1단계: DNAC의 패브릭 디바이스에서 멀티캐스트 구성
DNAC GUI의 Provision(프로비저닝) -> Fabric Workflow(패브릭 워크플로)에서. 멀티캐스트는 SDA-BORDER-1 디바이스에서 "Enable Rendezvous point" 옵션으로 구성됩니다.
그런 다음 특정 VN에서 멀티캐스트 구성에 사용할 인터넷 프로토콜(IP) 풀을 선택합니다. 이 예에서는 "Campus"입니다.
2단계: 디바이스에서 푸시된 컨피그레이션 확인
이 섹션에서는 패브릭 디바이스에서 멀티캐스트 컨피그레이션을 확인하는 방법을 다룹니다.
SDA-국경-1
interface Loopback4099 <<<<<<<<<<<< Loopback Interface is created and assigned an IP from Pool selected
vrf forwarding Campus
ip address 192.168.50.1 255.255.255.255
ip pim sparse-mode <<<<<<<<<<< PIM is enabled on Interface
end
interface LISP0.4099 <<<<<<<<<<< PIM is enabled on LISP interface
ip pim sparse-mode
end
SDA-Border1#sh run | in pim|multicast ip multicast-routing <<<<<<<<<<< Multicast Routing is enabled for Global ip multicast-routing vrf Campus <<<<<<<<<<< Multicast Routing is enabled for Campus VN ip pim ssm default <<<<<<<<<< PIM SSM mode is enabled for Global for default address range ip pim vrf Campus rp-address 192.168.50.1 <<<<<<<<<< BORDER-1 Loopback4099 is configued as RP
ip pim vrf Campus register-source Loopback4099
ip pim vrf Campus ssm default <<<<<<<<<< PIM SSM mode is enabled for vrf Campus for default address range
SDA-Border1#sh run | s address-family ipv4 vrf Campus
address-family ipv4 vrf Campus
.....
network 192.168.50.1 mask 255.255.255.255 <<<<<<<<<<< RP Address is injected into BGP Table
aggregate-address 192.168.50.0 255.255.255.0 summary-only <<<<<<<<<<< Aggregate for Multicast Pool is advertised
.....
SDA-국경-2
interface Loopback4099 vrf forwarding Campus ip address 192.168.50.3 255.255.255.255 ip pim sparse-mode end interface LISP0.4099 ip pim sparse-mode end SDA-Border2#sh run | in pim|multicast ip multicast-routing ip multicast-routing vrf Campus ip pim ssm default ip pim vrf Campus rp-address 192.168.50.1 <<<<<<<<<< BORDER-1 Loopback4099 is configued as RP ip pim vrf Campus register-source Loopback4099 ip pim vrf Campus ssm default
SDA-Border2#sh run | s address-family ipv4 vrf Campus
address-family ipv4 vrf Campus
.....
network 192.168.50.1 mask 255.255.255.255
aggregate-address 192.168.50.0 255.255.255.0 summary-only
.....
SDA-엣지-1
interface Vlan1021
description Configured from apic-em
mac-address 0000.0c9f.f45c
vrf forwarding Campus
ip address 172.16.10.1 255.255.255.0
ip helper-address 10.10.10.100
no ip redirects
ip local-proxy-arp
ip pim sparse-mode <<<<<<<<<<< PIM is enabled on all SVI-s under Campus VN
ip route-cache same-interface
ip igmp version 3
no lisp mobility liveness test
lisp mobility 172_16_10_0-Campus
end
interface Loopback4099 vrf forwarding Campus ip address 192.168.50.2 255.255.255.255 ip pim sparse-mode end interface LISP0.4099 ip pim sparse-mode end SDA-Edge1#sh run | in pim|multicast ip multicast-routing ip multicast-routing vrf Campus ip pim ssm default ip pim vrf Campus rp-address 192.168.50.1 <<<<<<<<<< BORDER-1 Loopback4099 is configued as RP ip pim vrf Campus register-source Loopback4099 ip pim vrf Campus ssm default
3단계: 핸드오버 링크 전반에서 PIM 수동 구성
이 예에서는 멀티캐스트 소스가 패브릭 외부에서 Fusion-2에 연결됩니다. 멀티캐스트 스트림이 흐르도록 하려면 RP에서 소스로, 수신자에서 소스로 PIM 경로가 있는지 확인합니다(경로는 다를 수 있음!).
SDA-BORDER-1과 SDA-FUSION-1 간의 PIM 피어링
SDA-BORDER-1 ------------------------------------------------ interface Vlan3002 <<<<<<<< Enable PIM on Handover link in Campus VN description vrf interface to External router vrf forwarding Campus ip address 10.50.50.5 255.255.255.252 no ip redirects ip pim sparse-mode ip route-cache same-interface end SDA-FUSION-1 ------------------------------------------------ ip multicast-routing ip multicast-routing vrf Campus <<<<<<<<< Enable Multicast Routing in vrf Campus
ip pim vrf Campus rp-address 192.168.50.1 <<<<<<<<< Configure BORDER-1 Loopback4099 as RP
interface Vlan3002 <<<<<<<<< Enable PIM on Fusion Interface towards Border vrf forwarding Campus ip address 10.50.50.6 255.255.255.252 ip pim sparse-mode end
SDA-BORDER-2 및 SDA-FUSION-2 간의 PIM 피어링
SDA-BORDER-2 ------------------------------------------------ interface Vlan3007 description vrf interface to External router vrf forwarding Campus ip address 10.50.50.25 255.255.255.252 no ip redirects ip pim sparse-mode ip route-cache same-interface end SDA-FUSION-2 ------------------------------------------------ ip multicast-routing distributed ip multicast-routing vrf Campus distributed ip pim vrf Campus rp-address 192.168.50.1 interface GigabitEthernet0/0/0.3007 encapsulation dot1Q 3007 vrf forwarding Campus ip address 10.50.50.26 255.255.255.252 ip pim sparse-mode no cdp enable end
SDA-FUSION-1과 SDA-FUSION-2 간의 PIM 피어링
SDA-FUSION-1 ------------------------------------------------ interface Vlan100 description Muticast_Campus vrf forwarding Campus ip address 10.40.40.5 255.255.255.252 ip pim sparse-mode end SDA-FUSION-2 ------------------------------------------------ interface GigabitEthernet0/0/2.100 encapsulation dot1Q 100 vrf forwarding Campus ip address 10.40.40.6 255.255.255.252 ip pim sparse-mode end
소스에 연결된 인터페이스에서 PIM 활성화
SDA-FUSION-2 ------------------------------------------------- interface GigabitEthernet1/0/2 vrf forwarding Campus ip address 10.40.40.2 255.255.255.252 ip pim sparse-mode load-interval 30 negotiation auto end
컨트롤 플레인 프로세스
멀티캐스트 수신자는 특정 그룹에 대한 스트림을 수신하기 위해 IGMP(Internet Group Management Protocol) Join to LHR(Last Hop Router)을 전송하고 멀티캐스트 소스(서버)는 멀티캐스트 스트림을 FHR(First Hop Router)로 전송하기 시작합니다. 이 경우 FHR은 SDA-FUSION-2이고 LHR은 SDA-EDGE-1이며 Control Plane Process는 Receiver가 먼저 스트림을 요청하고 Source가 그 이후에 해당 그룹에 대한 스트리밍을 시작하는 시나리오에서 설명합니다.
LHR에서 IGMP 조인
멀티캐스트 수신기는 그룹 239.1.1.1에 대해 LHR에 IGMP 보고서(조인)를 보냅니다. 수신기는 SDA-EDGE-1의 Gi1/0/1(SVI 1021)에 연결됩니다.
SDA-Edge1#debug ip igmp vrf Campus 239.1.1.1 IGMP debugging is on *Aug 14 23:53:06.445: IGMP(4): Received v2 Report on Vlan1021 from 172.16.10.10 for 239.1.1.1 *Aug 14 23:53:06.445: IGMP(4): Received Group record for group 239.1.1.1, mode 2 from 172.16.10.10 for 0 sources *Aug 14 23:53:06.445: IGMP(4): MRT Add/Update Vlan1021 for (*,239.1.1.1) by 0 *Aug 14 23:54:07.445: IGMP(4): Received v2 Report on Vlan1021 from 172.16.10.10 for 239.1.1.1 <<<<<<< one minute apart
SDA-Edge1#show ip igmp vrf Campus group
IGMP Connected Group Membership
Group Address Interface Uptime Expires Last Reporter
239.1.1.1 Vlan1021 00:49:10 00:02:45 172.16.10.10 <<<<<<< Receiver is present
SDA-Edge1#
새로운 멀티캐스트 경로 감시 서비스는 RP(공유 트리)와 소스(SPT(Shortest Path Tree))에 대한 RPF(Reverse Path Forwarding) 정보를 결정합니다. LISP 연결 가능 주소의 경우 다음 홉 네이버는 업스트림 사이트의 RLOC(remote Routing Locator) 주소로 표시됩니다.
SDA-Edge1#show ip pim vrf Campus rp mapping 239.1.1.1
PIM Group-to-RP Mappings
Group(s): 224.0.0.0/4, Static
RP: 192.168.50.1 (?) <<<<<<<<<<< RP is 192.168.50.1
SDA-Edge1#
SDA-Edge1#
SDA-Edge1#show lisp eid-table vrf Campus ipv4 map 192.168.50.1/32 <<<<<<<<< check Reachability towards the RP address
LISP IPv4 Mapping Cache for EID-table vrf Campus (IID 4099), 4 entries
192.168.50.1/32, uptime: 2w5d, expires: 23:10:58, via map-reply, complete
Sources: map-reply
State: complete, last modified: 2w5d, map-source: 192.168.10.1
Active, Packets out: 171704(3435172 bytes) (~ 00:00:43 ago)
Locator Uptime State Pri/Wgt Encap-IID
192.168.10.1 2w5d up 10/10 - <<<<<<<<<<< RLOC is 192.168.10.1
Last up-down state change: 2w5d, state change count: 1
Last route reachability change: 2w5d, state change count: 1
Last priority / weight change: never/never
RLOC-probing loc-status algorithm:
Last RLOC-probe sent: 00:49:02 (rtt 3ms)
SDA-Edge1#show ip cef vrf Campus 192.168.50.1/32
192.168.50.1/32
nexthop 192.168.10.1 LISP0.4099 <<<<<<<<<<< RP is reachable via LISP interface
SDA-Edge1#show ip mroute vrf Campus 239.1.1.1
IP Multicast Routing Table
(*, 239.1.1.1), 00:50:06/00:02:57, RP 192.168.50.1, flags: SJC <<<<<<<<<<< (*,G) entry is created
Incoming interface: LISP0.4099, RPF nbr 192.168.10.1 <<<<<<<<<<< Incoming interface is set as LISP interface
Outgoing interface list:
Vlan1021, Forward/Sparse, 00:50:06/00:02:57 <<<<<<<<<<< Outgoing Interface is set towards Receiver
그런 다음 LHR이 해당 세그먼트에 대한 DR인 경우 LHR은 RP를 향해 PIM(*,G) Join Forward를 전송합니다(1분 간격으로).
SDA-Edge1#debug ip pim vrf Campus 239.1.1.1 PIM debugging is on *Aug 15 00:03:44.592: PIM(4): Building Periodic (*,G) Join / (S,G,RP-bit) Prune message for 239.1.1.1 *Aug 15 00:03:44.593: PIM(4): Insert (*,239.1.1.1) join in nbr 192.168.10.1's queue *Aug 15 00:03:44.593: PIM(4): Building Join/Prune packet for nbr 192.168.10.1 *Aug 15 00:03:44.594: PIM(4): Adding v2 (192.168.50.1/32, 239.1.1.1), WC-bit, RPT-bit, S-bit Join *Aug 15 00:03:44.594: PIM(4): Adding LISP Unicast transport attribute in join/prune to 192.168.10.1 (LISP0.4099) *Aug 15 00:03:44.594: PIM(4): Send v2 join/prune to 192.168.10.1 (LISP0.4099) <<<<<<< PIM (*,G) Join is sent towards the RP
*Aug 15 00:04:42.892: PIM(4): Building Periodic (*,G) Join / (S,G,RP-bit) Prune message for 239.1.1.1 *Aug 15 00:04:42.892: PIM(4): Insert (*,239.1.1.1) join in nbr 192.168.10.1's queue *Aug 15 00:04:42.892: PIM(4): Building Join/Prune packet for nbr 192.168.10.1 *Aug 15 00:04:42.892: PIM(4): Adding v2 (192.168.50.1/32, 239.1.1.1), WC-bit, RPT-bit, S-bit Join *Aug 15 00:04:42.892: PIM(4): Adding LISP Unicast transport attribute in join/prune to 192.168.10.1 (LISP0.4099) *Aug 15 00:04:42.892: PIM(4): Send v2 join/prune to 192.168.10.1 (LISP0.4099) SDA-Edge1#
네이버 생성
LISP 인터페이스를 가리키는 RPF 정보를 얻은 후에는 PIM에서 해당 RLOC에 대한 인접 디바이스 구조를 명시적으로 만들어야 합니다. 이는 xTR(Upstream Tunnel Router)이 hello 메시지를 보내지 않기 때문에 필요합니다. 새 인접 디바이스 블록은 join/prune 메시지가 join/prune 간에 표준 간격 시간의 2배 이후에 인접 디바이스로 전송되지 않을 때 만료됩니다.
이 경우 SDA-EDGE-1은 업스트림/RPF RLOC 주소를 사용하여 PIM 인접 디바이스를 생성합니다.
SDA-Edge1#show ip pim vrf Campus neighbor PIM Neighbor Table Neighbor Interface Uptime/Expires Ver DR Address Prio/Mode 192.168.10.1 LISP0.4099 1w5d/00:01:27 v2 0 / <<<<<<< RLOC address used for the neighbor SDA-Edge1#debug ip pim vrf Campus timers <— chatty! PIM-TIMERS debugging is on
*Aug 15 00:08:37.992: PIM(4): Building Periodic (*,G) Join / (S,G,RP-bit) Prune message for 239.1.1.1 *Aug 15 00:08:37.993: PIM(4) Twheel Start: Neighbor Timer for Nbr: 192.168.10.1. idb LISP0.4099. delay: 120000 ms. jitter 0. ...
RP에서 수신된 PIM 조인
PIM 조인은 LSP 인터페이스를 통해 LHR(SDA-EDGE-1)에서 RP(SDA-BORDER-1)로 수신됨
SDA-Border1#debug ip pim vrf Campus 239.1.1.1 PIM debugging is on *Aug 18 01:47:14.812: PIM(4): J/P Transport Attribute, Transport Type: Unicast *Aug 18 01:47:14.813: PIM(4): Join-list: (*, 239.1.1.1), RPT-bit set, WC-bit set, S-bit set *Aug 18 01:47:14.813: PIM(4): Check RP 192.168.50.1 into the (*, 239.1.1.1) entry *Aug 18 01:47:14.813: PIM(4): Adding register decap tunnel (Tunnel1) as accepting interface of (*, 239.1.1.1). *Aug 18 01:47:14.813: PIM(4): Add LISP0.4099/192.168.10.3 to (*, 239.1.1.1), Forward state, by PIM *G Join <<<<<< (*,G) join received from RLOC of LHR over LISP Interface *Aug 18 01:48:14.267: PIM(4): J/P Transport Attribute, Transport Type: Unicast *Aug 18 01:48:14.267: PIM(4): Join-list: (*, 239.1.1.1), RPT-bit set, WC-bit set, S-bit set *Aug 18 01:48:14.267: PIM(4): Update LISP0.4099/192.168.10.3 to (*, 239.1.1.1), Forward state, by PIM *G Join
SDA-Border1#show ip mroute vrf Campus 239.1.1.1 IP Multicast Routing Table (*, 239.1.1.1), 00:01:38/00:02:51, RP 192.168.50.1, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 <<<<<<<<<<<< RP is myself hence RPF Neighbor is Null Outgoing interface list: LISP0.4099, 192.168.10.3, Forward/Sparse, 00:01:38/00:02:51 <<<<<<<<<<<< Outgoing Interface is set towards LHR RLOC
RP(Border1)는 LISP 인터페이스를 통해 조인을 전송하지 않으므로 LISP 인터페이스를 통해 RP에 PIM 인접 디바이스가 생성되지 않습니다.
이 경우 유일한 PIM 네이버는 비 LISP 인터페이스를 통해 Fusion-1을 향하고 있으며 수신된 주기적인 PIM Hello 패킷의 결과로 형성됩니다.
SDA-Border1#debug ip pim vrf Campus hello
PIM-HELLO debugging is on
SDA-Border1#
*Aug 24 00:02:19.944: PIM(4): Received v2 hello on Vlan3002 from 10.50.50.6
*Aug 24 00:02:19.944: PIM(4): Neighbor (10.50.50.6) Hello GENID = 1315387214
SDA-Border1#
*Aug 24 00:02:49.396: PIM(4): Received v2 hello on Vlan3002 from 10.50.50.6
*Aug 24 00:02:49.397: PIM(4): Neighbor (10.50.50.6) Hello GENID = 1315387214
SDA-Border1#show ip pim vrf Campus neigh PIM Neighbor Table Neighbor Interface Uptime/Expires Ver DR Address Prio/Mode 10.50.50.6 Vlan3002 2w0d/00:01:31 v2 1 / DR S P G
Fusion 라우터의 PIM 네이버
Fusion Router의 PIM 네이버는 비 LISP 인터페이스를 통해 생성되므로 수신된 주기적인 PIM Hello-s를 기반으로 생성됩니다.
SDA-FUSION-1 SDA-Fusion1#show ip pim vrf Campus neighbor PIM Neighbor Table Neighbor Interface Uptime/Expires Ver DR Address Prio/Mode 10.40.40.6 Vlan100 5d00h/00:01:41 v2 1 / S P G 10.50.50.5 Vlan3002 2w4d/00:01:44 v2 1 / S P G SDA-FUSION-2 SDA-Fusion2#show ip pim vrf Campus neighbor PIM Neighbor Table Neighbor Interface Uptime/Expires Ver DR Address Prio/Mode 10.50.50.25 Gi0/0/0.3007 2w5d/00:01:36 v2 1 / S P G 10.40.40.5 GigabitEthernet0/0/2.100 5d00h/00:01:23 v2 100/ DR S P G
FHR에서 RP의 PIM 등록
소스가 그룹에 대한 트래픽을 보내기 시작하면 FHR(SDA-FUSION-2)은 (S,G)가 소스에서 첫 번째 멀티캐스트 패킷을 받으면 RP에 등록합니다. FHR이 해당 세그먼트의 DR인 경우
SDA-Fusion2#show ip pim vrf Campus rp mapping 239.1.1.1
PIM Group-to-RP Mappings
Group(s): 224.0.0.0/4, Static
RP: 192.168.50.1 (?) <<<<<<<< RP for the Group
SDA-Fusion2#show ip cef vrf Campus 192.168.50.1
192.168.50.1/32
nexthop 10.40.40.5 GigabitEthernet0/0/2.100 <<<<<<<< Next-hop Interface towards RP
SDA-Fusion2#debug ip mrouting vrf Campus
IP multicast routing debugging is on
SDA-Fusion2#debug ip pim vrf Campus
PIM debugging is on
*Aug 22 21:59:42.601: PIM(2): Check RP 192.168.50.1 into the (*, 239.1.1.1) entry
*Aug 22 21:59:42.601: MRT(2): (*,239.1.1.1), RPF change from /0.0.0.0 to GigabitEthernet0/0/2.100/10.40.40.5 <<<<<<<< RPF Interface is determined
*Aug 22 21:59:42.601: PIM(2): Building Triggered (*,G) Join / (S,G,RP-bit) Prune message for 239.1.1.1
*Aug 22 21:59:42.601: MRT(2): Create (*,239.1.1.1), RPF (GigabitEthernet0/0/2.100, 10.40.40.5, 1/0)
*Aug 22 21:59:42.602: MRT(2): (10.40.40.1,239.1.1.1), RPF install from /0.0.0.0 to GigabitEthernet1/0/2/0.0.0.0
*Aug 22 21:59:42.602: PIM(2): Adding register encap tunnel (Tunnel0) as forwarding interface of (10.40.40.1, 239.1.1.1). <<<<< Register Tunnel is created
*Aug 22 21:59:42.602: MRT(2): Set the F-flag for (*, 239.1.1.1)
*Aug 22 21:59:42.602: MRT(2): Set the F-flag for (10.40.40.1, 239.1.1.1) <<<<<<< Register(F) flag is set
*Aug 22 21:59:42.602: MRT(2): Create (10.40.40.1,239.1.1.1), RPF (GigabitEthernet1/0/2, 0.0.0.0, 0/0) <<<<<<< (S,G) is created
*Aug 22 21:59:42.602: MRT(2): Set the T-flag for (10.40.40.1, 239.1.1.1) <<<<<<< SPT (T) flag is set
*Aug 22 21:59:42.629: PIM(2): Received v2 Join/Prune on GigabitEthernet0/0/2.100 from 10.40.40.5, to us
*Aug 22 21:59:42.629: PIM(2): Join-list: (10.40.40.1/32, 239.1.1.1), S-bit set <<<<<<< (S,G) join is received
*Aug 22 21:59:42.629: MRT(2): WAVL Insert interface: GigabitEthernet0/0/2.100 in (10.40.40.1,239.1.1.1) Successful
*Aug 22 21:59:42.630: MRT(2): set min mtu for (10.40.40.1, 239.1.1.1) 18010->1500
*Aug 22 21:59:42.630: MRT(2): Add GigabitEthernet0/0/2.100/239.1.1.1 to the olist of (10.40.40.1, 239.1.1.1), Forward state - MAC built
*Aug 22 21:59:42.630: PIM(2): Add GigabitEthernet0/0/2.100/10.40.40.5 to (10.40.40.1, 239.1.1.1), Forward state, by PIM SG Join
*Aug 22 21:59:42.630: MRT(2): Add GigabitEthernet0/0/2.100/239.1.1.1 to the olist of (10.40.40.1, 239.1.1.1), Forward state - MAC built
*Aug 22 21:59:42.630: MRT(2): Set the PIM interest flag for (10.40.40.1, 239.1.1.1)
SDA-Fusion2#show ip mroute vrf Campus 239.1.1.1
IP Multicast Routing Table
(*, 239.1.1.1), 00:01:17/stopped, RP 192.168.50.1, flags: SPF
Incoming interface: GigabitEthernet0/0/2.100, RPF nbr 10.40.40.5
Outgoing interface list: Null
(10.40.40.1, 239.1.1.1), 00:01:17/00:02:14, flags: FT
Incoming interface: GigabitEthernet1/0/2, RPF nbr 0.0.0.0 <<<<<<<< RPF neighbor is 0.0.0.0 as the Source is directly connected
Outgoing interface list:
Gi0/0/0.3007, Forward/Sparse, 00:01:17/00:03:10
SDA-Fusion2#
SDA-Fusion2#show interface tunnel 0 <<<<<<<< Register Tunnel is created between FHR and RP
Tunnel0 is up, line protocol is up
Hardware is Tunnel
Description: Pim Register Tunnel (Encap) for RP 192.168.50.1 on VRF Campus
Interface is unnumbered. Using address of GigabitEthernet0/0/2.100 (10.40.40.6)
MTU 9972 bytes, BW 100 Kbit/sec, DLY 50000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation TUNNEL, loopback not set
Keepalive not set
Tunnel linestate evaluation up
Tunnel source 10.40.40.6 (GigabitEthernet0/0/2.100), destination 192.168.50.1
RP(BORDER-1)는 FHR에서 레지스터를 수신하므로 (S,G) Join을 FHR로 보내고 FHR로 Register-Stop을 보냅니다. RP에서 스트림이 기본적으로 수신되면.
SDA-Border1#debug ip mrouting vrf Campus 239.1.1.1
IP multicast routing debugging is on
*Aug 18 02:29:05.186: PIM(4): Received v2 Register on Vlan3002 from 10.40.40.6 <<<<<<< PIM Register is received from FHR
*Aug 18 02:29:05.186: for 10.40.40.1, group 239.1.1.1
*Aug 18 02:29:05.187: PIM(4): Adding register decap tunnel (Tunnel1) as accepting interface of (10.40.40.1, 239.1.1.1). <<<<<<< Register tunnel is created
*Aug 18 02:29:05.187: MRT(4): (10.40.40.1,239.1.1.1), RPF install from /0.0.0.0 to Vlan3002/10.50.50.6
*Aug 18 02:29:05.188: MRT(4): Create (10.40.40.1,239.1.1.1), RPF (Vlan3002, 10.50.50.6, 20/0) <<<<<<< (S,G) is created and RPF is resolved
*Aug 18 02:29:05.188: MRT(4): WAVL Insert LISP interface: LISP0.4099 in (10.40.40.1,239.1.1.1) Next-hop: 192.168.10.3 Outer-source: 0.0.0.0 Successful
*Aug 18 02:29:05.188: MRT(4): set min mtu for (10.40.40.1, 239.1.1.1) 18010->17892
*Aug 18 02:29:05.189: MRT(4): Add LISP0.4099/192.168.10.3 to the olist of (10.40.40.1, 239.1.1.1), Forward state - MAC not built <<<<<< LISP OIF is inherited from (*,G)
*Aug 18 02:29:05.189: PIM(4): Insert (10.40.40.1,239.1.1.1) join in nbr 10.50.50.6's queue
*Aug 18 02:29:05.189: PIM(4): Building Join/Prune packet for nbr 10.50.50.6
*Aug 18 02:29:05.189: PIM(4): Adding v2 (10.40.40.1/32, 239.1.1.1), S-bit Join
*Aug 18 02:29:05.189: PIM(4): Send v2 join/prune to 10.50.50.6 (Vlan3002) <<<<<<< (S,G) join is sent towards the Source
*Aug 18 02:29:05.272: PIM(4): J/P Transport Attribute, Transport Type: Unicast
*Aug 18 02:29:05.272: PIM(4): Join-list: (*, 239.1.1.1), RPT-bit set, WC-bit set, S-bit set
*Aug 18 02:29:05.272: PIM(4): Update LISP0.4099/192.168.10.3 to (*, 239.1.1.1), Forward state, by PIM *G Join
*Aug 18 02:29:05.272: MRT(4): Update LISP0.4099/192.168.10.3 in the olist of (*, 239.1.1.1), Forward state - MAC not built
*Aug 18 02:29:05.272: PIM(4): Prune-list: (10.40.40.1/32, 239.1.1.1) RPT-bit set
*Aug 18 02:29:05.273: PIM(4): Prune LISP0.4099/192.168.10.3 from (10.40.40.1/32, 239.1.1.1) <<<<<<< (S,G) Prune is received from Edge1
*Aug 18 02:29:05.273: MRT(4): Delete LISP0.4099/192.168.10.3 from the olist of (10.40.40.1, 239.1.1.1)
*Aug 18 02:29:05.273: PIM(4): Insert (10.40.40.1,239.1.1.1) prune in nbr 10.50.50.6's queue - deleted
*Aug 18 02:29:05.273: PIM(4): Building Join/Prune packet for nbr 10.50.50.6
*Aug 18 02:29:05.273: PIM(4): Adding v2 (10.40.40.1/32, 239.1.1.1), S-bit Prune
*Aug 18 02:29:05.273: PIM(4): Send v2 join/prune to 10.50.50.6 (Vlan3002)
*Aug 18 02:29:05.439: PIM(4): J/P Transport Attribute, Transport Type: Unicast
*Aug 18 02:29:07.193: PIM(4): Received v2 Register on Vlan3002 from 10.40.40.6
*Aug 18 02:29:07.193: for 10.40.40.1, group 239.1.1.1
*Aug 18 02:29:07.194: PIM(4): Send v2 Register-Stop to 10.40.40.6 for 10.40.40.1, group 239.1.1.1 <<<<<<< Register-Stop is sent towards FHR
SDA-Border1#show ip mroute vrf Campus 239.1.1.1
IP Multicast Routing Table
(*, 239.1.1.1), 00:51:28/00:02:44, RP 192.168.50.1, flags: S
Incoming interface: Null, RPF nbr 0.0.0.0
Outgoing interface list:
LISP0.4099, 192.168.10.3, Forward/Sparse, 00:51:28/00:02:44
(10.40.40.1, 239.1.1.1), 00:09:37/00:01:24, flags: P <<<<<<<<<<<< (S,G) is created but Pruned flag is set
Incoming interface: Vlan3002, RPF nbr 10.50.50.6 <<<<<<<<<<<< Incoming interface and RPF neighbor
Outgoing interface list: Null
SDA-Border1#show ip rpf vrf Campus 10.40.40.1
RPF information for ? (10.40.40.1)
RPF interface: Vlan3002 <<<<<<<<<< RPF interface towards the Source
RPF neighbor: ? (10.50.50.6) <<<<<<<<<< RPF neighbor - must be a PIM neighbor
RPF route/mask: 10.40.40.0/30
RPF type: unicast (bgp 65005) <<<<<<<<<< RPF information coming from unicast RIB/BGP
Doing distance-preferred lookups across tables
RPF topology: ipv4 multicast base, originated from ipv4 unicast base
SDA-Border1#
SDA-Border1#show ip route vrf Campus 10.40.40.1
Routing Table: Campus
Routing entry for 10.40.40.0/30
Known via "bgp 65005", distance 20, metric 0
Tag 65004, type external
Last update from 10.50.50.6 2w6d ago
Routing Descriptor Blocks:
* 10.50.50.6, from 10.50.50.6, 2w6d ago
Route metric is 0, traffic share count is 1
AS Hops 1
Route tag 65004
MPLS label: none
MPLS Flags: NSF
SDA-Border1#
SPT가 Edge-1에서 정리되고 있습니다. 이유를 알아보려면 LHR로 이동하십시오.
(S,G) LHR에서 생성
RP에서 전달된 멀티캐스트 데이터를 수신한 후 LHR에 (S,G) 엔트리가 생성됩니다.
그런 다음 LHR이 SPT(Shortest Path Tree)로 전환됩니다)를 전송할 수 있습니다. 이는 RPF 인터페이스에서 소스로 전송됩니다.
SDA-Edge1#
*Aug 18 02:19:53.759: MRT(4): Create (10.40.40.1,239.1.1.1), RPF (unknown, 0.0.0.0, 0/0) <<<<<<<<< (S,G) is created on LHR
*Aug 18 02:19:53.759: MRT(4): WAVL Insert interface: Vlan1021 in (10.40.40.1,239.1.1.1) Successful
*Aug 18 02:19:53.759: MRT(4): set min mtu for (10.40.40.1, 239.1.1.1) 18010->1500
*Aug 18 02:19:53.759: MRT(4): Add Vlan1021/239.1.1.1 to the olist of (10.40.40.1, 239.1.1.1), Forward state - MAC not built <<<<<<< OIL is inherited from (*,G)
*Aug 18 02:19:53.759: MRT(4): Set the J-flag for (10.40.40.1, 239.1.1.1) <<<<<<<< SPT Join Flag is set
*Aug 18 02:19:53.762: MRT(4): (10.40.40.1,239.1.1.1), RPF change from /0.0.0.0 to LISP0.4099/192.168.10.2 <<<<<<<< RPF interface is resolved
*Aug 18 02:19:53.762: MRT(4): Set the T-flag for (10.40.40.1, 239.1.1.1)
*Aug 18 02:19:53.763: PIM(4): Insert (10.40.40.1,239.1.1.1) join in nbr 192.168.10.2's queue
*Aug 18 02:19:53.763: PIM(4): Building Join/Prune packet for nbr 192.168.10.2
*Aug 18 02:19:53.763: PIM(4): Adding v2 (10.40.40.1/32, 239.1.1.1), S-bit Join
*Aug 18 02:19:53.763: PIM(4): Adding LISP Unicast transport attribute in join/prune to 192.168.10.2 (LISP0.4099)
*Aug 18 02:19:53.763: PIM(4): Send v2 join/prune to 192.168.10.2 (LISP0.4099) <<<<<<<< (S,G) Join towards the Source is sent
*Aug 18 02:19:53.826: PIM(4): Building Periodic (*,G) Join / (S,G,RP-bit) Prune message for 239.1.1.1
*Aug 18 02:19:53.826: PIM(4): Insert (*,239.1.1.1) join in nbr 192.168.10.1's queue
*Aug 18 02:19:53.826: PIM(4): Insert (10.40.40.1,239.1.1.1) sgr prune in nbr 192.168.10.1's queue
*Aug 18 02:19:53.826: PIM(4): Building Join/Prune packet for nbr 192.168.10.1
*Aug 18 02:19:53.826: PIM(4): Adding v2 (192.168.50.1/32, 239.1.1.1), WC-bit, RPT-bit, S-bit Join
*Aug 18 02:19:53.827: PIM(4): Adding v2 (10.40.40.1/32, 239.1.1.1), RPT-bit, S-bit Prune
*Aug 18 02:19:53.827: PIM(4): Adding LISP Unicast transport attribute in join/prune to 192.168.10.1 (LISP0.4099)
*Aug 18 02:19:53.827: PIM(4): Send v2 join/prune to 192.168.10.1 (LISP0.4099) <<<<<<<<< (S,G) Prune towards the RP is sent
*Aug 18 02:20:08.323: MRT(4): Update (*,239.1.1.1), RPF (LISP0.4099, 192.168.10.1, 1/1)
*Aug 18 02:20:08.323: MRT(4): Update Vlan1021/239.1.1.1 in the olist of (*, 239.1.1.1), Forward state - MAC not built
*Aug 18 02:20:08.323: MRT(4): Update Vlan1021/239.1.1.1 in the olist of (10.40.40.1, 239.1.1.1), Forward state - MAC not built
SDA-Edge1#show ip mroute vrf Campus 239.1.1.1
IP Multicast Routing Table
(*, 239.1.1.1), 00:43:35/stopped, RP 192.168.50.1, flags: SJC
Incoming interface: LISP0.4099, RPF nbr 192.168.10.1
Outgoing interface list:
Vlan1021, Forward/Sparse, 00:43:35/00:02:29
(10.40.40.1, 239.1.1.1), 00:01:45/00:01:14, flags: JT <<<<<<<<<<<< (S,G) is created
Incoming interface: LISP0.4099, RPF nbr 192.168.10.2 <<<<<<<<<<<< Border-2 is the RPF neighbor towards the Source
Outgoing interface list:
Vlan1021, Forward/Sparse, 00:01:47/00:02:27
SDA-Edge1#show lisp eid-table vrf Campus ipv4 map 10.40.40.1 <<<<<<<< LISP lookup for the Source
LISP IPv4 Mapping Cache for EID-table vrf Campus (IID 4099), 5 entries
0.0.0.0/1, uptime: 2w1d, expires: 18:05:53, via map-reply, forward-native
Sources: map-reply
State: forward-native, last modified: 2w1d, map-source: 192.168.10.1
Active, Packets out: 106458(41136237 bytes) (~ 00:00:38 ago)
Encapsulating to proxy ETR <<<<<<<<< No specific entry is known, forwarding to Proxy ETR
SDA-Edge1#show ip cef vrf Campus 10.40.40.1 detail
0.0.0.0/1, epoch 0, flags [subtree context, check lisp eligibility], per-destination sharing
SC owned,sourced: LISP remote EID - locator status bits 0x00000000
LISP remote EID: 106468 packets 41140303 bytes fwd action encap
LISP source path list
nexthop 192.168.10.1 LISP0.4099 <<<<<<<<<< Load balancing towards 2 Proxy ETR-s
nexthop 192.168.10.2 LISP0.4099
2 IPL sources [no flags]
nexthop 192.168.10.1 LISP0.4099
nexthop 192.168.10.2 LISP0.4099
SDA-Edge1#show ip cef vrf Campus exact-route 192.168.50.2 10.40.40.1 <<<<<<<<< CEF hashing points towards Border-2
192.168.50.2 -> 10.40.40.1 =>IP adj out of GigabitEthernet1/0/11, addr 192.168.23.2
SDA-Edge1#show ip rpf vrf Campus 10.40.40.1
RPF information for ? (10.40.40.1)
RPF interface: LISP0.4099
RPF neighbor: ? (192.168.10.2) <<<<<<<<<< Hence SPT Join is sent towards Border-2
RPF route/mask: 0.0.0.0/1
RPF type: unicast ()
Doing distance-preferred lookups across tables
RPF topology: ipv4 multicast base
SDA-Edge1#
(S,G) 조인이 LISP 인터페이스를 통해 Border-2로 전송되므로 Edge-1에서 새 PIM 인접 디바이스가 생성됩니다
SDA-Edge1#show ip pim vrf Campus neighbor PIM Neighbor Table Neighbor Interface Uptime/Expires Ver DR Address Prio/Mode 192.168.10.2 LISP0.4099 00:07:32/00:01:22 v2 0 / <<<<<<<< Neighbor towards Border-2 is created 192.168.10.1 LISP0.4099 2w1d/00:01:58 v2 0 /
Border-2는 멀티캐스트 스트림의 데이터 경로에 있으므로 패킷의 유니캐스트 복제를 위해 다운스트림 XTR-s의 RLOC를 추적하려면 명시적 RLOC 추적을 수행해야 합니다.
SDA-Border2#show ip mroute vrf Campus 239.1.1.1
IP Multicast Routing Table
(*, 239.1.1.1), 00:23:00/stopped, RP 192.168.50.1, flags: SP
Incoming interface: LISP0.4099, RPF nbr 192.168.10.1
Outgoing interface list: Null
(10.40.40.1, 239.1.1.1), 00:12:35/00:02:52, flags: T <<<<<<< SPT flag is set
Incoming interface: Vlan3007, RPF nbr 10.50.50.26 <<<<<<< RPF neighbor is based on RPF towards the Source - must be a PIM neighbor
Outgoing interface list:
LISP0.4099, 192.168.10.3, Forward/Sparse, 00:12:35/00:02:45 <<<<<<< OIL created from (S,G) join received from LHR and containing LHR's RLOC info which has to be tracked
SDA-Border2#show ip mfib vrf Campus 239.1.1.1 10.40.40.1
Entry Flags: C - Directly Connected, S - Signal, IA - Inherit A flag,
ET - Data Rate Exceeds Threshold, K - Keepalive
DDE - Data Driven Event, HW - Hardware Installed
ME - MoFRR ECMP entry, MNE - MoFRR Non-ECMP entry, MP - MFIB
MoFRR Primary, RP - MRIB MoFRR Primary, P - MoFRR Primary
MS - MoFRR Entry in Sync, MC - MoFRR entry in MoFRR Client.
I/O Item Flags: IC - Internal Copy, NP - Not platform switched,
NS - Negate Signalling, SP - Signal Present,
A - Accept, F - Forward, RA - MRIB Accept, RF - MRIB Forward,
MA - MFIB Accept, A2 - Accept backup,
RA2 - MRIB Accept backup, MA2 - MFIB Accept backup
Forwarding Counts: Pkt Count/Pkts per second/Avg Pkt Size/Kbits per second
Other counts: Total/RPF failed/Other drops
I/O Item Counts: FS Pkt Count/PS Pkt Count
VRF Campus
(10.40.40.1,239.1.1.1) Flags: HW
SW Forwarding: 0/0/0/0, Other: 0/0/0
HW Forwarding: 176/0/122/0, Other: 0/0/0 <<<<<<< Multicast stream is forwarded in h/w
Vlan3007 Flags: A
LISP0.4099, 192.168.10.3 Flags: F NS
Pkts: 0/0
SDA-Border2#sh ip mfib vrf Campus 239.1.1.1 10.40.40.1 count
Forwarding Counts: Pkt Count/Pkts per second/Avg Pkt Size/Kilobits per second
Other counts: Total/RPF failed/Other drops(OIF-null, rate-limit etc)
VRF Campus
6 routes, 2 (*,G)s, 3 (*,G/m)s
Group: 239.1.1.1
Source: 10.40.40.1,
SW Forwarding: 0/0/0/0, Other: 0/0/0
HW Forwarding: 182/0/122/0, Other: 0/0/0 <<<<<<<< Counter is incrementing
Totals - Source count: 1, Packet count: 182
Groups: 1, 1.00 average sources per group
SDA-Border2#
피드백