この製品のマニュアルセットは、偏向のない言語を使用するように配慮されています。このマニュアルセットでの偏向のない言語とは、年齢、障害、性別、人種的アイデンティティ、民族的アイデンティティ、性的指向、社会経済的地位、およびインターセクショナリティに基づく差別を意味しない言語として定義されています。製品ソフトウェアのユーザーインターフェイスにハードコードされている言語、RFP のドキュメントに基づいて使用されている言語、または参照されているサードパーティ製品で使用されている言語によりドキュメントに例外が存在する場合があります。シスコのインクルーシブランゲージに対する取り組みの詳細は、こちらをご覧ください。
このドキュメントは、米国シスコ発行ドキュメントの参考和訳です。リンク情報につきましては、日本語版掲載時点で、英語版にアップデートがあり、リンク先のページが移動/変更されている場合がありますことをご了承ください。あくまでも参考和訳となりますので、正式な内容については米国サイトのドキュメントを参照ください。
目次
この章は、次の項で構成されています。
E シリーズ サーバ には、同一の CIMC ファームウェア イメージが 2 つ搭載された状態で出荷されます。 E シリーズ サーバ がブートするイメージ コピーを選択できます。 E シリーズ サーバ がブートするイメージ コピーは現在のイメージで、もう 1 つのイメージ コピーはバックアップ イメージです。
E シリーズ サーバ のブートに問題がある場合は、現在の CIMC ファームウェアが破損しているか、SD カードに問題があるか、CIMC ファームウェアのインストールが正常に終了しなかったことが原因として考えられます。 破損した CIMC ファームウェア イメージから回復するには、次のいずれかの操作を適宜実行してください。
現在の CIMC ファームウェア イメージが破損しており、バックアップ イメージがある場合は、そのバックアップ イメージを使用して E シリーズ サーバ をブートします。 バックアップ イメージからの E シリーズ サーバのブートを参照してください。
現在のイメージとバックアップ イメージが両方とも破損している場合は、破損した現在およびバックアップのイメージの復旧を参照してください。
SD カードに問題がある場合は、「障害がある SD カードからの復旧」を参照してください。
CIMC ファームウェアのインストールが正常に終了しなかった場合は、CIMC ファームウェアを再インストールします。
現在の CIMC ファームウェア イメージが破損しており、バックアップ イメージがある場合は、そのバックアップ イメージを使用して E シリーズ サーバ をブートします。
この例では、バックアップ イメージから E シリーズ サーバをブートします。
Router# hw-module subslot 2/0 stop
Router# hw-module subslot 2/0 start
***
ucse-cimc > boot backup
unknown login: admin
password: password
次の例では、現在のイメージから CIMC ファームウェアが復旧されます。
Router# hw-module subslot 2/0 stop Router# hw-module subslot 2/0 start *** ucse-cimc > boot current recovery recovery-shell# dedicated-interface 192.168.0.138 255.255.255.0 192.168.0.1 Network configuration: IP config: addr: 192.168.0.138 Mask: 255.255.255.0 Gateway: 192.168.0.1 recovery-shell# ping 10.20.34.56 PING 10.20.34.56 (10.20.34.56): 56 data bytes 64 bytes from 10.20.34.56: seq=0 ttl=60 time=10.000 ms 64 bytes from 10.20.34.56: seq=1 ttl=60 time=0.000 ms --- 10.20.34.56 ping statistics --- 10 packets transmitted, 10 packets received, 0% packet loss round-trip min/avg/max = 0.000/1.000/10.000 ms recovery-shell# update 10.20.34.56 update_pkg-cimc.combined.bin downloading firmware image "update_pkg-cimc.combined.bin" from " 10.20.34.56 " download firmware image done, size in bytes: 22384144 installing firmware image, please wait ... activating installed image done Stage: NONE Status: SUCCESS Error: Success recovery-shell# reboot
次の例では、現在のイメージから CIMC ファームウェアが復旧されます。
Router# hw-module subslot 2/0 stop Router# hw-module subslot 2/0 start *** ucse-cimc > boot current recovery recovery-shell# dedicated-interface 192.168.0.138 255.255.255.0 192.168.0.1 Network configuration: IP config: addr: 192.168.0.138 Mask: 255.255.255.0 Gateway: 192.168.0.1 recovery-shell# ping 10.20.34.56 PING 10.20.34.56 (10.20.34.56): 56 data bytes 64 bytes from 10.20.34.56: seq=0 ttl=60 time=10.000 ms 64 bytes from 10.20.34.56: seq=1 ttl=60 time=0.000 ms --- 10.20.34.56 ping statistics --- 10 packets transmitted, 10 packets received, 0% packet loss round-trip min/avg/max = 0.000/1.000/10.000 ms recovery-shell# update 10.20.34.56 update_pkg-cimc.combined.bin downloading firmware image "update_pkg-cimc.combined.bin" from " 10.20.34.56 " download firmware image done, size in bytes: 22384144 installing firmware image, please wait ... activating installed image done Stage: NONE Status: SUCCESS Error: Success recovery-shell# reboot
目次
この章は、次の項で構成されています。
CIMC ファームウェア イメージの概要
E シリーズ サーバ には、同一の CIMC ファームウェア イメージが 2 つ搭載された状態で出荷されます。 E シリーズ サーバ がブートするイメージ コピーを選択できます。 E シリーズ サーバ がブートするイメージ コピーは現在のイメージで、もう 1 つのイメージ コピーはバックアップ イメージです。
E シリーズ サーバ のブートに問題がある場合は、現在の CIMC ファームウェアが破損しているか、SD カードに問題があるか、CIMC ファームウェアのインストールが正常に終了しなかったことが原因として考えられます。 破損した CIMC ファームウェア イメージから回復するには、次のいずれかの操作を適宜実行してください。
現在の CIMC ファームウェア イメージが破損しており、バックアップ イメージがある場合は、そのバックアップ イメージを使用して E シリーズ サーバ をブートします。 バックアップ イメージからの E シリーズ サーバのブートを参照してください。
現在のイメージとバックアップ イメージが両方とも破損している場合は、破損した現在およびバックアップのイメージの復旧を参照してください。
SD カードに問題がある場合は、「障害がある SD カードからの復旧」を参照してください。
CIMC ファームウェアのインストールが正常に終了しなかった場合は、CIMC ファームウェアを再インストールします。
バックアップ イメージからの E シリーズ サーバのブート
手順
破損した現在およびバックアップのイメージの復旧
手順
次の例では、現在のイメージから CIMC ファームウェアが復旧されます。
Router# hw-module subslot 2/0 stop Router# hw-module subslot 2/0 start *** ucse-cimc > boot current recovery recovery-shell# dedicated-interface 192.168.0.138 255.255.255.0 192.168.0.1 Network configuration: IP config: addr: 192.168.0.138 Mask: 255.255.255.0 Gateway: 192.168.0.1 recovery-shell# ping 10.20.34.56 PING 10.20.34.56 (10.20.34.56): 56 data bytes 64 bytes from 10.20.34.56: seq=0 ttl=60 time=10.000 ms 64 bytes from 10.20.34.56: seq=1 ttl=60 time=0.000 ms --- 10.20.34.56 ping statistics --- 10 packets transmitted, 10 packets received, 0% packet loss round-trip min/avg/max = 0.000/1.000/10.000 ms recovery-shell# update 10.20.34.56 update_pkg-cimc.combined.bin downloading firmware image "update_pkg-cimc.combined.bin" from " 10.20.34.56 " download firmware image done, size in bytes: 22384144 installing firmware image, please wait ... activating installed image done Stage: NONE Status: SUCCESS Error: Success recovery-shell# reboot障害がある SD カードからの復旧
手順
次の例では、現在のイメージから CIMC ファームウェアが復旧されます。
Router# hw-module subslot 2/0 stop Router# hw-module subslot 2/0 start *** ucse-cimc > boot current recovery recovery-shell# dedicated-interface 192.168.0.138 255.255.255.0 192.168.0.1 Network configuration: IP config: addr: 192.168.0.138 Mask: 255.255.255.0 Gateway: 192.168.0.1 recovery-shell# ping 10.20.34.56 PING 10.20.34.56 (10.20.34.56): 56 data bytes 64 bytes from 10.20.34.56: seq=0 ttl=60 time=10.000 ms 64 bytes from 10.20.34.56: seq=1 ttl=60 time=0.000 ms --- 10.20.34.56 ping statistics --- 10 packets transmitted, 10 packets received, 0% packet loss round-trip min/avg/max = 0.000/1.000/10.000 ms recovery-shell# update 10.20.34.56 update_pkg-cimc.combined.bin downloading firmware image "update_pkg-cimc.combined.bin" from " 10.20.34.56 " download firmware image done, size in bytes: 22384144 installing firmware image, please wait ... activating installed image done Stage: NONE Status: SUCCESS Error: Success recovery-shell# reboot