レイヤ 3 インターフェイス設定時の注意事項および制約事項
レイヤ 3 インターフェイスを設定する際に、以下の注意事項と制約事項に従ってください。
• 設定するレイヤ 3 VLAN インターフェイスは 2,000 個までにすることを推奨します。
• ip unnumbered コマンドは、レイヤ 3 VLAN インターフェイスでサポートされます。
• VLAN インターフェイスをサポートするには、VLAN を作成および設定し、レイヤ 2 LAN ポートに VLAN メンバシップを割り当てます。詳細については、 第 12 章「VLAN の設定」 および 第 11 章「VLAN トランキング プロトコル(VTP)の設定」 を参照してください。
• Catalyst 6500 シリーズ スイッチは、以下をサポートしません。
– Integrated Routing and Bridging(IRB)
– Concurrent Routing and Bridging(CRB)
– Remote Source-Route Bridging(RSRB; リモート ソースルート ブリッジング)
• VLAN インターフェイスでブリッジ グループ(代替ブリッジングとも言う)を使用して、ルーティングされないプロトコルをブリッジします。VLAN インターフェイスのブリッジ グループは、PISA のソフトウェアでサポートされます。
• Catalyst 6500 シリーズ スイッチは、ブリッジ グループの IEEE ブリッジング プロトコルをサポートしません。VLAN ブリッジまたは DEC スパニングツリー プロトコルを使用してブリッジ グループを設定します。
レイヤ 3 インターフェイスのサブインターフェイスの設定
レイヤ 3 サブインターフェイスを設定する際に、以下の注意事項と制約事項に従ってください。
• LAN ポート サブインターフェイスでは、次の機能がサポートされます。
– MPLS VPNを含む IPv4 ユニキャスト フォワーディング
– MPLS VPNを含む IPv4 マルチキャスト フォワーディング
– 6PE
– EoMPLS
– 番号付けされていない IPv4
– MIBS 内の show vlans コマンドを使用したサブインターフェイス用カウンタ
– iBGP および eBGP
– OSPF
– EIGRP
– RIPv1/v2
– RIPv2
– ISIS
– スタティック ルーティング
– UniDirectional Link Routing(UDLR; 単一方向リンク ルーティング)
– IGMPv1、IGMPv2、IGMPv3
– PIMv1、PIMv2
– SSM IGMPv3lite および URD
– スタブ IP マルチキャスト ルーティング
– IGMP Join
– IGMP スタティック グループ
– Multicast Routing Monitor(MRM)
– Multicast Source Discovery Protocol(MSDP)
– SSM
– IPv4 ping
– IPv6 ping
• VLAN ID が IEEE 802.1Q ネイティブ VLAN の ID の場合、 native キーワードを必ず使用してください。 native キーワードを使用せずに、IEEE 802.1Q トランクのネイティブ VLAN でカプセル化を設定しないでください。
• VLAN ID はswitchに対してグローバルであるため、サブインターフェイス上、またはレイヤ 3 VLAN インターフェイスに関して VLAN を内部的に使用することができます。
– サブインターフェイスまたはレイヤ 3 VLAN インターフェイスで、内部 VLAN の設定はできません。
– レイヤ 3 VLAN インターフェイスで、サブインターフェイス VLAN の設定はできません。
– サブインターフェイス上では、レイヤ 3 VLAN インターフェイスとともに使用される VLAN の設定はできません。
(注) 1 つのインターフェイス、別のインターフェイスのサブインターフェイス、またはサブインターフェイスで使用されている VLAN の設定はできません。
• VLAN Trunking Protocol(VTP; VLAN トランキング プロトコル)トランスペアレント モードでは、任意の標準範囲または拡張範囲の VLAN ID を使用して、サブインターフェイスを設定することができます。VLAN ID 1 ~ 1005 は、VTP ドメインでグローバルであり、VTP ドメイン内の他のネットワーク装置上で定義することができるため、VTP クライアント/サーバ モードでは、拡張範囲 VLAN だけをサブインターフェイスとともに使用することができます。VTP クライアント/サーバ モードでは、標準範囲 VLAN がサブインターフェイスから除外されます。
(注) サブインターフェイス上で標準範囲 VLAN を設定する場合、VTP モードをトランスペアレントから変更できません。
サブインターフェイスを設定するには、次の作業を行います。
|
|
|
ステップ 1 |
Router> enable |
特権 EXEC モードを開始します。 |
ステップ 2 |
Router# configure terminal |
グローバル コンフィギュレーション モードを開始します。 |
ステップ 3 |
Router(config)# interface {{ type slot / port . subinterface } | { port-channel port_channel_number . subinterface }} |
インターフェイスを選択して、サブインターフェイス コンフィギュレーション モードを開始します。 |
ステップ 4 |
Router(config-subif)# encapsulation dot1q vlan_ID [ native ] |
サブインターフェイスの 802.1Q カプセル化を設定します。 |
ステップ 5 |
Router(config-if)# exit |
グローバル コンフィギュレーション モードに戻ります。 |
IPv4 ルーティングおよびアドレスの設定
詳しい説明および設定手順については、次のマニュアルを参照してください。
• 次の URL の『 Cisco IOS IP and IP Routing Configuration Guide 』Release 12.2
http://www.cisco.com/en/US/docs/ios/12_2/ip/configuration/guide/fipr_c.html
• 次の URL の『 Cisco IOS IP and IP Routing Command Reference 』Release 12.2
http://www.cisco.com/en/US/docs/ios/12_2/ipaddr/command/reference/fipras_r.html
http://www.cisco.com/en/US/docs/ios/12_2/iproute/command/reference/fiprrp_r.html
IPv4 ルーティングおよびアドレスを設定する際に、以下の注意事項と制約事項に従ってください。
• maximum paths コマンドの詳細については、『 Catalyst Supervisor Engine 32 PISA Cisco IOS Command Reference , Release 12.2ZY』を参照してください。
• Policy Feature Card 3B(PFC3B; ポリシー フィーチャ カード 3B)は、 match ip address 、 set ip next-hop 、および ip default next-hop Policy-Based Routing(PBR; ポリシーベース ルーティング)キーワードを使用するルート マップ シーケンス用の PBR をハードウェアでサポートします。
PBR を設定する際に、以下の注意事項と制約事項に従ってください。
– PFC3B はトンネル インターフェイスに設定されている PBR のハードウェア サポートを提供します。
– PFC3B は、ネクスト ホップがトンネル インターフェイスである場合に set ip next-hop キーワードで設定されている PBR のハードウェア サポートを提供しません。
– PISA アドレスが PBR ACL 範囲内にある場合、PISA にアドレス指定されたトラフィックは PISA に転送されずに、ハードウェアでポリシー ルーティングされます。PISA にアドレス指定されたトラフィックをポリシー ルーティングしないようにするには、PISA にアドレス指定されたトラフィックを拒否するように PBR ACL を設定します。
– Cisco IOS ACL のオプションの中で、PISA に送信されソフトウェアでスイッチングされるフローが発生するような PBR ルート マップでのフィルタリングを実行するものは無視されます。たとえば、PBR ルート マップでのフィルタリングを行う Cisco IOS ACL の ACE で、ロギングはサポートされていません。
– PBR が設定されているスイッチング モジュール ポートを通過する PBR トラフィックは、スイッチング モジュールがリセットされる場合にソフトウェアでルーティングされます。(CSCee92191)
PBR の設定については、次の URL の『 Cisco IOS Quality of Service Solutions Configuration Guide 』Release 12.2 の「Classification」、「Configuring Policy-Based Routing」を参照してください。
http://www.cisco.com/en/US/docs/ios/12_2/qos/configuration/guide/qcfpbr_ps1835_TSD_Products_Configuration_Guide_Chapter.html
レイヤ 3 インターフェイスに IPv4 ルーティングおよび IPv4 アドレスを設定するには、次の作業を行います。
|
|
|
ステップ 1 |
Router(config)# ip routing |
IPv4 ルーティングをイネーブルにします。(IPv4 ルーティングがディセーブルになっている場合だけ必須)。 |
ステップ 2 |
Router(config)# router ip_routing_protocol |
IPv4 ルーティング プロトコルを指定します。 |
ステップ 3 |
Router(config-router)# ip_routing_protocol_commands |
IPv4 ルーティング プロトコルを設定します。 |
ステップ 4 |
Router(config-router)# exit |
IPv4 ルーティング プロトコルのコンフィギュレーション モードを終了します。 |
ステップ 5 |
Router(config)# interface { vlan vlan_ID } | { type slot/port } | { port-channel port_channel_number } |
設定するインターフェイスを選択します。 |
ステップ 6 |
Router(config-if)# ip address ip_address subnet_mask |
IPv4 アドレスおよび IPv4 サブネットを設定します。 |
ステップ 7 |
Router(config-if)# no shutdown |
インターフェイスをイネーブルにします。 |
ステップ 8 |
Router(config-if)# end |
コンフィギュレーション モードを終了します。 |
ステップ 9 |
Router# show interfaces [{ vlan vlan_ID } | { type1 slot/port } | { port-channel port_channel_number }] Router# show ip interfaces [{ vlan vlan_ID } | { type1 slot/port } | { port-channel port_channel_number }] Router# show running-config interfaces [{ vlan vlan_ID } | { type1 slot/port } | { port-channel port_channel_number }] |
設定を確認します。 |
次に、IPv4 Routing Information Protocol(RIP)ルーティングをイネーブルにする例を示します。
Router# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)# ip routing
Router(config)# router rip
Router(config-router)# network 10.0.0.0
Router(config-router)# end
次に、ポート FastEthernet 5/4 に IPv4 アドレスを設定する例を示します。
Router# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)# interface fastethernet 5/4
Router(config-if)# ip address 172.20.52.106 255.255.255.248
Router(config-if)# no shutdown
次に、show interfaces コマンドを使用して、ポート FastEthernet 5/4 のインターフェイス IPv4 アドレスの設定およびステータスを表示する例を示します。
Router# show interfaces fastethernet 5/4
FastEthernet5/4 is up, line protocol is up
Hardware is Cat6K 100Mb Ethernet, address is 0050.f0ac.3058 (bia 0050.f0ac.3058)
Internet address is 172.20.52.106/29
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:01, output never, output hang never
Last clearing of "show interface" counters never
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
7 packets input, 871 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
8 packets output, 1658 bytes, 0 underruns
0 output errors, 0 collisions, 4 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
次に、show ip interface コマンドを使用して、ポート FastEthernet 5/4 の詳細な設定およびステータスを表示する例を示します。
Router# show ip interface fastethernet 5/4
FastEthernet5/4 is up, line protocol is up
Internet address is 172.20.52.106/29
Broadcast address is 255.255.255.255
Address determined by setup command
Helper address is not set
Directed broadcast forwarding is disabled
Multicast reserved groups joined: 224.0.0.10
Outgoing access list is not set
Inbound access list is not set
Security level is default
ICMP redirects are always sent
ICMP unreachables are always sent
ICMP mask replies are never sent
IP fast switching is enabled
IP fast switching on the same interface is disabled
IP Flow switching is disabled
IP CEF switching is enabled
IP Fast switching turbo vector
IP Normal CEF switching turbo vector
IP multicast fast switching is enabled
IP multicast distributed fast switching is disabled
Router Discovery is disabled
IP output packet accounting is disabled
IP access violation accounting is disabled
TCP/IP header compression is disabled
RTP/IP header compression is disabled
Probe proxy name replies are disabled
Policy routing is disabled
Network address translation is disabled
WCCP Redirect outbound is disabled
WCCP Redirect exclude is disabled
BGP Policy Mapping is disabled
IP multicast multilayer switching is disabled
IP mls switching is enabled
次に、show running-config コマンドを使用して、ポート FastEthernet 5/4 のインターフェイス IPv4 アドレスの設定を表示する例を示します。
Router# show running-config interfaces fastethernet 5/4
Building configuration...
interface FastEthernet5/4
description "Router port"
ip address 172.20.52.106 255.255.255.248
IPX ルーティングおよびネットワーク番号の設定
(注) PISA は、高速スイッチングで Internetwork Packet Exchange(IPX)をサポートします。
詳しい説明および設定手順については、次のマニュアルを参照してください。
• 次の URL の『 Cisco IOS AppleTalk and Novell IPX Configuration Guide 』Release 12.2
http://www.cisco.com/en/US/docs/ios/12_2/atipx/configuration/guide/fatipx_c.html
• 次の URL の『 Cisco IOS AppleTalk and Novell IPX Command Reference 』Release 12.2
http://www.cisco.com/en/US/docs/ios/12_2/atipx/command/reference/fatipx_r.html
IPX ルーティングを設定し、レイヤ 3 インターフェイスに IPX を設定するには、次の作業を行います。
|
|
|
ステップ 1 |
Router(config)# ipx routing |
IPX ルーティングをイネーブルにします。 |
ステップ 2 |
Router(config)# router ipx_routing_protocol |
IP ルーティング プロトコルを指定します。 このステップでは、他のコマンド(ルーティングするネットワークを指定する network コマンドなど)を使用する場合があります。 |
ステップ 3 |
Router(config)# interface { vlan vlan_ID } | { type slot/port } | { port-channel port_channel_number } |
設定するインターフェイスを選択します。 |
ステップ 4 |
Router(config-if)# ipx network [ network | unnumbered ] encapsulation encapsulation_type |
IPX ネットワーク番号を設定します。このステップにより、インターフェイス上で IPX ルーティングがイネーブルになります。インターフェイス上で IPX ルーティングをイネーブルにするとき、カプセル化タイプも指定できます。 |
ステップ 5 |
Router(config-if)# no shutdown |
インターフェイスをイネーブルにします。 |
ステップ 6 |
Router(config-if)# end |
コンフィギュレーション モードを終了します。 |
ステップ 7 |
Router# show interfaces [{ vlan vlan_ID } | { type1 slot/port } | { port-channel port_channel_number }] Router# show ipx interfaces [{ vlan vlan_ID } | { type1 slot/port } | { port-channel port_channel_number }] Router# show running-config interfaces [{ vlan vlan_ID } | { type1 slot/port } | { port-channel port_channel_number }] |
設定を確認します。 |
次に、IPX ルーティングをイネーブルにし、インターフェイス VLAN100 に IPX ネットワーク アドレスを割り当てる例を示します。
Router# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)# ipx routing
Router(config)# ipx router rip
Router(config-ipx-router)# network all
Router(config-ipx-router)# interface vlan 100
Router(config-if)# ipx network 100 encapsulation snap
Router(config-if)# no shutdown
Router# copy running-config startup-config
AppleTalk ルーティング、ケーブルの範囲、およびゾーンの設定
詳しい説明および設定手順については、次のマニュアルを参照してください。
• 次の URL の『 Cisco IOS AppleTalk and Novell IPX Configuration Guide 』Release 12.2
http://www.cisco.com/en/US/docs/ios/12_2/atipx/configuration/guide/fatipx_c.html
• 次の URL の『 Cisco IOS AppleTalk and Novell IPX Command Reference 』Release 12.2
http://www.cisco.com/en/US/docs/ios/12_2/atipx/command/reference/fatipx_r.html
AppleTalk ルーティングを設定するには、グローバル コンフィギュレーション モードで次の作業を行います。
|
|
|
ステップ 1 |
Router(config)# appletalk routing |
AppleTalk ルーティングを イネーブルにします。 |
ステップ 2 |
Router(config)# interface { vlan vlan_ID } | { type slot/port } | { port-channel port_channel_number } |
設定するインターフェイスを選択します。 |
ステップ 3 |
Router(config-if)# appletalk cable-range cable_range |
インターフェイスにケーブル範囲を割り当てます。 |
ステップ 4 |
Router(config-if)# appletalk zone zone_name |
インターフェイスにゾーン名を割り当てます。 |
ステップ 5 |
Router(config-if)# no shutdown |
インターフェイスをイネーブルにします。 |
ステップ 6 |
Router(config-if)# end |
コンフィギュレーション モードを終了します。 |
ステップ 7 |
Router# show interfaces [{ vlan vlan_ID } | { type1 slot/port } | { port-channel port_channel_number }] Router# show appletalk interfaces [{ vlan vlan_ID } | { type1 slot/port } | { port-channel port_channel_number }] Router# show running-config interfaces [{ vlan vlan_ID } | { type1 slot/port } | { port-channel port_channel_number }] |
設定を確認します。 |
次に、AppleTalk ルーティングをイネーブルにして、インターフェイス VLAN 100 に AppleTalk ケーブルの範囲およびゾーン名を割り当てる例を示します。
Router# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)# appletalk routing
Router(config)# interface vlan 100
Router(config-if)# appletalk cable-range 100-100
Router(config-if)# appletalk zone Engineering
Router(config-if)# no shutdown
Router# copy running-config startup-config