Sommario

Introduzione

Prerequisiti

Requisiti

Componenti usati

Convenzioni

Configurazione

AS5300: Cisco IOS - Compatibilità software Voice Feature Card (VFC)

Configurare E1 R2

Esempio di rete

Configurazioni

Verifica

Risoluzione dei problemi

Risoluzione dei problemi relativi agli errori E1 R2

Comandi debug e show

Output di esempio del comando debug

Informazioni correlate

Introduzione

Questo documento offre le voci di comando progressive necessarie per implementare la segnalazione E1 R2. In questo documento vengono anche fornite informazioni sulla risoluzione dei problemi con i comandi di debug.

Nota: prima di utilizzare questo documento, si consiglia di leggere la teoria dei segnali E1 R2.

Prerequisiti

Requisiti

Prima di provare la configurazione, verificare che siano soddisfatti i seguenti prerequisiti:

- La segnalazione R2 si applica solo a E1.

- La segnalazione R2 non è supportata sul router Cisco MC3810.

- Per eseguire la segnalazione R2 sui router Cisco serie 2600/3600, è necessario questo hardware:

VWIC-1MFT-E1 o VWIC-2MFT-E1 o VWIC-2MFT-E1-DI insieme a uno dei seguenti moduli di densità vocale: NM-HDV (High Density Voice Network Module) o NM-HD-2VE (IP communications voice/fax network module a 2 slot) .

- Definire il comando ds0-group (o cas-group, in base alla versione di Cisco IOS®) sui controller E1 (AS5x00, router Cisco 2600/3600).

- Usare il comando cas-custom per personalizzare le varianti di E1 R2 per paesi diversi.

Componenti usati

Le informazioni di questo documento si basano sulla seguente versione software e hardware:

- Cisco AS5300 con software Cisco IOS versione 12.0.7T

Nota: la segnalazione E1 R2 è stata introdotta nei router Cisco serie 2600/3600 nel software Cisco IOS versione 12.1.2XH e 12.1(3)T.

Le informazioni discusse in questo documento fanno riferimento a dispositivi usati in uno specifico ambiente di emulazione. Su tutti i dispositivi menzionati nel documento la configurazione è stata ripristinata ai valori predefiniti. Se la rete è operativa, valutare attentamente eventuali conseguenze derivanti dall'uso dei comandi.

Convenzioni

Per ulteriori informazioni sulle convenzioni usate, consultare il documento Cisco sulle convenzioni nei suggerimenti tecnici.

Configurazione

In questa sezione vengono presentate le informazioni che è possibile utilizzare per configurare E1 R2.

Nota: per ulteriori informazioni sui comandi usati da questo documento, consultare lo strumento di ricerca dei comandi (solo utenti registrati).

AS5300: Cisco IOS - Compatibilità software Voice Feature Card (VFC)

Prima di implementare la segnalazione E1 R2 in un router Cisco AS5300, verificare che la versione del software Cisco IOS in uso sia compatibile con Cisco VCware nel modulo E1. Per verificare la compatibilità del software Cisco IOS, fare riferimento alla matrice di compatibilità VCWare per Cisco AS5300. Se le versioni non sono compatibili, i moduli del processore di segnale digitale (DSP) nella scheda voce non vengono caricati e non viene eseguita l'elaborazione del segnale vocale.

In genere, se la versione di Cisco VCWare non è compatibile con il software Cisco IOS, è possibile immettere il comando show vfc slot_number interface per verificare questa condizione, come mostrato nell'esempio.

eefje#show vfc 1 interface

Rx: in ptr 18, outptr 0

Tx: in ptr 14  outptr  14

0 in hw queue, 0 queue head , 0 queue tail

Hardware is VFC out-of-band channel

Interface : state RESET DSP instance (0x61048284)

dsp_number 0, Channel ID 0

TX outstanding 0, max TX outstanding 0

Received 18 packets, 1087 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

121 bytes output, 14 frames output

0 bounce errors 0

DSP module 1 is not installed

DSP module 2 is not installed

DSP module 3 is not installed

DSP module 4 is not installed

DSP module 5 is not installed

Nel primo output di esempio del comando show vfc slot_number interface, le istruzioni DSP module number is not installed mostrano che le versioni non sono compatibili per quel numero di modulo.

Questo secondo gruppo di output è un esempio di moduli DSP con la versione corretta di Cisco VCWare caricata:

eefje#show vfc 1 interface

Rx: in ptr 24, outptr 0

TX: in ptr 15  outptr  15

0 in hw queue, 0 queue head , 0 queue tail

Hardware is VFC out-of-band channel

Interface : state RESET DSP instance (0x618C6088)

dsp_number 0, Channel ID 0

TX outstanding 0, max TX outstanding 0

Received 283288 packets, 15864278 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

1416459 bytes output,  141647 frames output

0 bounce errors 0

Slot 1, DSPM 1 (C542), DSP 1, Channel 1

State RESET, DSP instance (0x61914BDC)

TX outstanding 0, max TX outstanding 8

Received 0 packets, 0 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

0 bytes output,  0 frames output

0 bounce errors 0

Slot 1, DSPM 1 (C542), DSP 2, Channel 1

State RESET, DSP instance (0x6191510C)

TX outstanding 0, max TX outstanding 8

Received 0 packets, 0 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

0 bytes output,  0 frames output

0 bounce errors 0

Per controllare la versione di Cisco VCWare installata, immettere il comando show vfc slot_number version vcware, come mostrato nell'esempio:

eefje#show vfc 1 version vcware

Voice Feature Card in Slot 1:

VCware Version : 4.10

ROM Monitor Version : 1.2

DSPware Version :

Technology :  C542

Nota: verificare che la versione della tecnologia Cisco VCWare (c549 o c542) corrisponda alla tecnologia VFC DSP installata (DSPM-542: supporto vocale a densità singola per DSPM-549: supporto vocale ad alta densità).

Configurare E1 R2

Completare questa procedura per configurare E1 R2:

1. Configurare il controller E1 che si connette allo switch o al PBX (Automatic Branch Exchange) privato.

Accertatevi che le impostazioni di framing e linecoding della E1 siano corrette.

2. Per il frame E1, scegliere CRC o non CRC.

3. Per la codifica lineare E1, scegliete HDB3 o AMI.

4. Per l'origine dell'orologio E1, scegliere interno o linea. Tenere presente che i diversi PBX hanno requisiti diversi sull'origine dell'orologio.

5. Configurare la segnalazione della linea.

6. Configurare la segnalazione tra registri.

7. Personalizzare la configurazione con il comando cas-custom.

Configura segnalazione linea

Utilizzare questa sequenza di comandi per definire la segnalazione sulla linea.

eefje(config)#controller E1 0

eefje(config-controller)#ds0-group 1 timeslots 1-15 type ?

...

r2-analog        R2 ITU Q411

r2-digital       R2 ITU Q421

r2-pulse         R2 ITU Supplement 7

...

Questa è la sequenza di comandi per il software Cisco IOS versione 11.3.

eefje(config)#controller E1 0

eefje(config-controller)#cas-group 1 timeslot 1-15 type ?

...

Nota: se si esegue l'aggiornamento dal software Cisco IOS versione 11.3 alla 12.0, il nuovo comando sostituisce automaticamente quello precedente.

Configura segnalazione tra registri

Questo esempio di sequenza di comandi illustra come configurare i diversi tipi di segnalazione tra registri:

eefje(config)#controller E1 0

eefje(config-controller)#ds0-group 1 timeslots 1-15 type r2-digital ?

dtmf               DTMF tone signaling

r2-compelled       R2 Compelled Register Signaling

r2-non-compelled   R2 Non Compelled Register Signaling

r2-semi-compelled  R2 Semi Compelled Register Signaling

Per impostazione predefinita, il supporto DNIS (Dialed Number Identification Service) è abilitato nell'implementazione Cisco della segnalazione R2. Se si attiva l'opzione ANI (Automatic Number Identification), la raccolta delle informazioni DNIS viene comunque eseguita. La specifica dell'opzione ANI non disabilita la raccolta DNIS. DNIS è il numero chiamato. ANI è il numero del chiamante. Ad esempio, se si configura un router denominato A per chiamare un router denominato B, il numero DNIS viene assegnato al router B e il numero ANI al router A. ANI è simile all'ID chiamante.

Personalizzazione di E1 R2 con il comando cas-custom

I sottocomandi del comando cas-custom vengono usati per adattarsi alle varianti del paese. Vengono inoltre utilizzati per personalizzare i parametri CAS (Channel Associated Signaling). In questa sequenza di comandi viene illustrato come visualizzare tutte le opzioni dei comandi personalizzati in base alla richiesta.

eefje(config)#controller E1 0

eefje(config-controller)#cas-custom 1

eefje(config-ctrl-cas)#?

CAS custom commands:

ani-digits           Expected number of ANI digits

ani-timeout          Timeout for ANI digits

answer-guard-time    Wait Between Group-B Answer Signal And Line Answer

answer-signal        Answer signal to be used

caller-digits        Digits to be collected before requesting CallerID

category             Category signal

country              Country Name

debounce-time        Debounce Timer

default              Set a command to its defaults

dnis-complete        Send I-15 after DNIS digits for dial-out

dnis-digits          Expected number of DNIS digits

exit                 Exit from cas custom mode

groupa-callerid-end  Send Group-A Caller ID End

invert-abcd          invert the ABCD bits before TX and after rx

ka                   kA Signal

kd                   KD Signal

metering             R2 network is sending metering signal

nc-congestion        Non Compelled Congestion signal

no                   Negate a command or set its defaults

proceed-to-send      Suppress proceed-to-send signal for pulsed line signaling

release-ack          Send Release Acknowledgment to Clear Forward

release-guard-time   Release Guard Timer

request-category     DNIS Digits to be collected before requesting category

seizure-ack-time     Seizure to Acknowledge timer

unused-abcd          Unused ABCD bit values

Per ulteriori informazioni sui parametri del comando cas-custom, consultare il documento sulla personalizzazione di E1 R2 con il comando cas-custom.

Esempio di rete

Nel documento viene usata questa impostazione di rete.

Configurazioni

Ai fini del presente documento, queste sono le tre diverse configurazioni di R2 mostrate nell'interfaccia E1:

- R2 Digitale non-forzato

- R2 Digitale semi-compattato

- R2 Impulso digitale ANI

Le configurazioni sono state modificate in modo da mostrare solo le informazioni discusse in questo documento.

eefje Configurato per R2 Digital Non-Compeled

hostname eefje

!

controller E1 0

clock source line primary

dso-group 1 timeslots 1-15 type r2-digital r2-non-compelled

cas-custom 1

!--- For more information on these commands !--- refer to  ds0-group  and  cas-custom.

!

voice-port 0:1

cptone BE

!--- The cptone command is country specific. For more !--- information on this command, refer to  cptone .

!

dial-peer voice 123 pots

destination-pattern 123

direct-inward-dial

port 0:1

prefix 123

!

dial-peer voice 567 voip

destination-pattern 567

session target ipv4:2.0.0.2

!

eefje configurato per R2 Digital Semi-Compeled

hostname eefje

!

controller E1 0

clock source line primary

ds0-group 1 timeslots 1-15 type r2-digital r2-semi-compelled

cas-custom 1

!--- For more information on these commands !--- refer to  ds0-group  and  cas-custom .

!

voice-port 0:1

cptone BE

!--- The cptone command is country specific. For more !--- information on this command, refer to  cptone .

dial-peer voice 123 pots

destination-pattern 123

direct-inward-dial

port 0:1

prefix 123

!

dial-peer voice 567 voip

destination-pattern 567

session target ipv4:2.0.0.2

!

eefje Configurato per R2 Digital Compeled ANI

hostname eefje

! controller E1 0 clock source line primary ds0-group

1 timeslots 1-15 type r2-digital r2-compelled ani cas-custom 1

!--- For more information on these commands !--- refer to  ds0-group  and  cas-custom .

voice-port 0:1 cptone BE

!--- The cptone command is country specific. For more !--- information on this command, refer to  cptone .

dial-peer voice 123 pots destination-pattern 123 direct-inward-dial port

0:1 prefix 123

!

dial-peer voice 567 voip destination-pattern 567 session

target ipv4:2.0.0.2

!

Verifica

Attualmente non è disponibile una procedura di verifica per questa configurazione.

Risoluzione dei problemi

Le informazioni contenute in questa sezione permettono di risolvere i problemi relativi alla configurazione.

Risoluzione dei problemi relativi agli errori E1 R2

Queste sono le informazioni utili per risolvere eventuali problemi con questa configurazione. Seguire queste istruzioni.

1. Verificare che il controller E1 0 sia attivo.

In caso di guasto, controllare i frame, la codifica della linea, l'origine dell'orologio, gli allarmi, sostituire il cavo, riposizionare la scheda e così via . Utilizzare Personalizzazione E1 R2 con il documento Cas-custom Command come riferimento.

2. Se si utilizza un AS5300, verificare che i DSP siano installati correttamente con il comando show vfc slot number interface.

3. Configurare Direct Inward Dial (DID) sul peer POTS (Plain Old Telephone Service), in modo che le cifre ricevute vengano utilizzate per scegliere un peer in uscita.

4. Specificare cptone (cptone è specifico del proprio paese) sulle porte vocali.

Affinché corrisponda al comando cas-custom country, è necessario configurare un comando cptonecountry. Il parametro cptone imposta i toni di avanzamento delle chiamate per un paese particolare e, cosa più importante, imposta la codifica su a-law o u-law, che dipende dal paese. La codifica predefinita per gli Stati Uniti è u-law.

5. Associare i dispositivi di segnalazione di linea e registro alla configurazione dello switch.

6. Attivare alcuni dei debug mostrati in questo documento e studiare gli output.

7. Verificare la comunicazione tra il router e il PBX o lo switch:

- La linea è bloccata?

- Il router riceve/invia cifre?

- Scoprite da quale parte la chiamata viene cancellata.

Se possibile, utilizzare le versioni software Cisco IOS più recenti disponibili sul sito Cisco.com.

Comandi debug e show

Alcuni comandi show sono supportati dallo strumento Output Interpreter (solo utenti registrati); lo strumento permette di visualizzare un'analisi dell'output del comando show.

Nota: prima di usare i comandi di debug, consultare le informazioni importanti sui comandi di debug.

Nota: per il software Cisco IOS versione 12.0, utilizzare i seguenti debug:

- debug cas - Per la segnalazione della linea.

- debug csm voice - Per la segnalazione tra registri.

- debug vtsp all: per scambiare l'output di tutti i messaggi (cifre) tra il PBX e il router.

Per il software Cisco IOS versione 11.3, utilizzare questi comandi:

- modem-mgmt csm debug-rbs: per la segnalazione in linea (è necessario specificare prima il servizio interno in modalità di configurazione).

- debug csm voice - Per la segnalazione tra registri.

- debug vtsp all: per scambiare l'output di tutti i messaggi (cifre) tra il PBX e il router.

Per le piattaforme AS5400 e AS5350, utilizzare i seguenti debug:

- debug sigsm r2 - Per segnalazione interregistro

- debug vtsp all: per scambiare l'output di tutti i messaggi (cifre) tra il PBX e il router.

Output di esempio del comando debug

Poiché in questo documento sono state illustrate tre configurazioni diverse, di seguito sono riportati tre debug diversi:

R2 Digitale non-forzato: Chiamata in arrivo a 567

Per una migliore comprensione dell'output del comando debug, consultare la teoria della segnalazione E1 R2.

eefje#show debug

CAS:

Channel Associated Signaling debugging is on

CSM Voice:

Voice Call Switching Module debugging is on

Voice Telephony session debugging is on

Voice Telephony dsp debugging is on

Voice Telephony error debugging is on

eefje#

eefje#

eefje#

Jan 6 10:41:28.677: from NEAT(0): (0/0): Rx SEIZURE (ABCD=0001)

Jan 6 10:41:28.717: VDEV_ALLOCATE: failed to allocate a device

Jan 6 10:41:28.717: VDEV_ALLOCATE: 1/28 is allocated

Jan 6 10:41:28.721: csm_vtsp_init_tdm (voice_vdev=0x620BF874)

Jan 6 10:41:28.721: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm slot 2,

dspm 1, dsp 5, dsp_channel 1

Jan 6 10:41:28.721: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm stream 5,

channel 3, bank 1, bp_channel 4, BP_stream 255

Jan 6 10:41:28.721: CSM_RX_CAS_EVENT_FROM_NEAT:(cid0018): EVENT_CALL_DIAL_IN

at slot 2 and port 16

Jan 6 10:41:28.721: CSM_PROC_IDLE: CSM_EVENT_START_DIGIT_COLLECT at slot 2,

port 16

Jan 6 10:41:28.721: csm_vtsp_start_digit_collect (voice_vdev=0x620BF874)

Jan 6 10:41:28.721:  Enter csm_connect_pri_vdev function

Jan 6 10:41:28.721: csm_connect_pri_vdev:tdm_allocate_BP_ts()call. BP TS allocated

at BP_stream0, BP_Ch28,vdev_common 0x6 20BF8E4

Jan 6 10:41:28.721: to NEAT:(cid0018) EVENT_CHANNEL_LOCK for slot0 ctlr0 chan0

Jan 6 10:41:28.721: vtsp_do_call_setup_ind

Jan 6 10:41:28.721: vtsp_do_call_setup_ind: Call ID=65681, guid=61FAF610

Jan 6 10:41:28.721: vtsp_do_call_setup_ind: type=0, under_spec=0, name=, id0=0,

id1=0, id2=0, calling=, called=

Jan 6 10:41:28.721: vtsp_do_call_setup_ind: redirect DN = reason =

0vtsp_open_voice_and_set_params

Jan 6 10:41:28.721: dsp_close_voice_channel: [0:1:0] packet_len=8 channel_id

=8529 packet_id=75

Jan 6 10:41:28.721: dsp_open_voice_channel_20: [0:1:0] packet_Len=16 channel_id

=8529 packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0 time_slot=0

serial_port=0

Jan 6 10:41:28.721: dsp_encap_config_20: [0:1:0] packet_Len=24 channel_id=8529

packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0

Jan 6 10:41:28.721: dsp_set_playout: [0:1:0] packet_Len=18 channel_id=8529

packet_id=76 mode=1 initial=60 min=4 max=200 fax_nom=300

Jan 6 10:41:28.721: dsp_echo_canceller_control: [0:1:0] packet_Len=10

channel_id=8529 packet_id=66 flags=0x0

Jan 6 10:41:28.721: dsp_set_gains: [0:1:0] packet_Len=12 channel_id=8529

packet_id=91 in_gain=0 out_gain=0

Jan 6 10:41:28.721: dsp_vad_enable: [0:1:0] packet_Len=10 channel_id=8529

packet_id=78 thresh=-38

Jan 6 10:41:28.721: dsp_voice_mode: [0:1:0] packet_Len=24 channel_id=8529

packet_id=73 coding_type=1 voice_field_size=80 V AD_flag=0 echo_length=64

comfort_noise=1 inband_detect=1 digit_relay=2

AGC_flag=0vtsp_do_r2_start_digit(): dsp_dtmf_mode()

dsp_dtmf_mode(VTSP_TONE_R2_MF_FORWARD_MODE)

Jan 6 10:41:28.725: dsp_dtmf_mode: [0:1:0] packet_Len=10 channel_id=8529

packet_id=65 dtmf_or_mf=1vtsp_do_r2_start_digit():fsm_push(vtsp_r2_state_table)

Jan 6 10:41:28.725: csm_vtsp_call_setup_resp (vdev_info=0x620BF874,

vtsp_cdb=0x621C5F3C)

Jan 6 10:41:28.725: csm_vtsp_call_setup_resp:vdev_common BP TS allocatedat

BP_stream0,BP_Ch28

Jan 6 10:41:28.725: csm_vtsp_call_setup_resp:dst_tdm_chnl call. BP TS allocatedat

stream 5, chan 3,BP_stream 255, BP_ch 4

Jan 6 10:41:28.725: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat

stream 5, chan 3,BP_stream 0, BP_ch 28

Jan 6 10:41:28.725: CSM_PROC_IC1_COLLECT_ADDR_INFO: CSM_EVENT_MODEM_OFFHOOK

(DNIS=, ANI=) at slot 2, port 16

Jan 6 10:41:28.725: R2 Incoming Voice(2/16): DSX (E1 0:0): STATE: R2_IN_IDLE R2

Got Event R2_START

Jan 6 10:41:28.821: CSM_RX_CAS_EVENT_FROM_NEAT:(0018):EVENT_START_RX_TONE at slot 2

and port 16

Jan 6 10:41:28.821: from NEAT(0): (0/0): TX SEIZURE_ACK (ABCD=1101)

!--- Digit 5 is sent: Forward Signal Group I-5.

Jan 6 10:41:29.233: vtsp_process_dsp_message:

MSG_TX_DTMF_DIGIT_BEGIN: digit=5,

rtp_timestamp=0x0CA95D43 dc_digit_up

Jan 6 10:41:29.233: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C) received digit (5)

Jan 6 10:41:29.233: CSM voice (2/16): Rcvd Digit detected(5)

Jan 6 10:41:29.233: R2 Incoming Voice(2/16): DSX (E1 0:0):

STATE: R2_IN_COLLECT_DNIS R2

Got Event 5

Jan 6 10:41:29.365: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=5,

duration=8321dc_digit

Jan 6 10:41:29.365: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C) received digit (5)

Jan 6 10:41:29.365: CSM voice (2/16): Rcvd Digit detected(5)

Jan 6 10:41:29.365: R2 Incoming Voice(2/16): DSX (E1 0:0):

STATE:R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_OFF

!--- Digit 6 is sent: Forward Signal Group I-6.

Jan 6 10:41:29.593: vtsp_process_dsp_message:

MSG_TX_DTMF_DIGIT_BEGIN: digit=6,

rtp_timestamp=0x0CA95D43 dc_digit_up

Jan 6 10:41:29.593: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C) received digit (6)

Jan 6 10:41:29.593: CSM voice (2/16): Rcvd Digit detected(6)

Jan 6 10:41:29.593: R2 Incoming Voice(2/16): DSX (E1 0:0):

STATE: R2_IN_COLLECT_DNIS R2

Got Event 6

Jan 6 10:41:29.725: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=6,

duration=8321dc_digit

Jan 6 10:41:29.725: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C) received digit (6)

Jan 6 10:41:29.725: CSM voice (2/16): Rcvd Digit detected(6)

Jan 6 10:41:29.725: R2 Incoming Voice(2/16): DSX (E1 0:0):

STATE: R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_OFF

!--- Digit 7 is sent: Forward Signal Group I-7.

Jan 6 10:41:29.953: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN:

digit=7, rtp_timestamp=0x0CA95D43 dc_digit_up

Jan 6 10:41:29.953: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C)

received digit (7)

Jan 6 10:41:29.953: CSM voice (2/16): Rcvd Digit detected(7)

Jan 6 10:41:29.953: R2 Incoming Voice(2/16): DSX (E1 0:0):

STATE:R2_IN_COLLECT_DNIS R2

Got Event 7

Jan 6 10:41:30.085: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF:

digit=7, duration=8321dc_digit

Jan 6 10:41:30.085: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C)received digit (7)

Jan 6 10:41:30.085: CSM voice (2/16): Rcvd Digit detected(7)

Jan 6 10:41:30.085: R2 Incoming Voice(2/16): DSX (E1 0:0):

STATE: R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_OFF

!--- Timeout: 3 seconds (default timer - AS5300 assumes DNIS is finished).

Jan 6 10:41:32.953: R2 Incoming Voice(2/16): DSX (E1 0:0):

STATE: R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_TIMER

!--- Send digit 6: Backward Signal Group B-6 (subscriber's line free-charge).

Jan 6 10:41:32.953: vtsp_r2_generate_digits: vdev_common=0x620BF8E4,

string=567dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 6#

Jan 6 10:41:32.953: dsp_dtmf_dialing: [0:1:0] packet_Len=36 channel_id=8529

packet_id=90 string=6# digits=2, time_on=150, time_off=30

Jan 6 10:41:32.953:&   digit=e, components=2, freq_of_first=900,

freq_of_second=780, amp_of_first=8192, amp_of_second=8192

Jan 6 10:41:32.953:    digit=o, components=2, freq_of_first=0,

freq_of_second=0, amp_of_first=1, amp_of_second=1

Jan 6 10:41:33.313: vtsp_process_dsp_message:

MSG_TX_DIALING_DONE dc_dialing_done()

Jan 6 10:41:33.313: R2 Incoming Voice(2/16): DSX (E1 0:0):

STATE:R2_IN_ANSWER_PULSE R2

Got Event R2_DIGITS_GENR2_ALERTING

Jan 6 10:41:34.313: R2 Incoming Voice(2/16): DSX (E1 0:0):

STATE: R2_IN_ANSWER_PULSE R2

Got Event R2_TONE_TIMER

Jan 6 10:41:34.313:  R2_IN_IDLE:2 r2_in_connect called

Jan 6 10:41:34.313: CSM_PROC_IC1_COLLECT_ADDR_INFO:

CSM_EVENT_ADDR_INFO_COLLECTED (DNIS=567, ANI=) at slot 2, port 16

Jan 6 10:41:34.313: vtsp_tsp_call_accept_check (sdb=0x61B8F0E0, calling_number=

called_number=567): peer_tag=0

Jan 6 10:41:34.313: VDEV_ALLOCATE: failed to allocate a device

Jan 6 10:41:34.313: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem

Jan 6 10:41:34.313: VDEV_ALLOCATE: failed to allocate a device

Jan 6 10:41:34.313: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem

Jan 6 10:41:34.313: VDEV_ALLOCATE: failed to allocate a device

Jan 6 10:41:34.313: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem

Jan 6 10:41:34.313: CSM_PROC_IC3_WAIT_FOR_RES_RESP: CSM_EVENT_RESOURCE_OK at slot 2,

port 16

Jan 6 10:41:34.313: vtsp_ic_switch : (voice_vdev= 0x620BF874)

Jan 6 10:41:34.313: vtsp_tsp_call_switch_ind (cdb=0x621C5F3C, tsp_info=0x620BF874,

calling_number= called_number=567 redir ect_number=):

peer_tag=123dc_switch: fsm_pop()

Jan 6 10:41:34.313: vtsp_do_call_setup_ind

Jan 6 10:41:34.313: vtsp_do_call_setup_ind: Call ID=65683, guid=61FAF610

Jan 6 10:41:34.313: vtsp_do_call_setup_ind: type=0, under_spec=0,

name=ab^Lx, id0=1, id1=0, id2=0, calling=123, called=567

Jan 6 10:41:34.317: dsp_cp_tone_off: [] packet_Len=8 channel_id=8529 packet_id=71

Jan 6 10:41:34.317: dsp_idle_mode: [] packet_Len=8 channel_id=8529 packet_id=68

Jan 6 10:41:34.317: dsp_close_voice_channel: [] packet_Len=8 channel_id=8529

packet_id=75

Jan 6 10:41:34.317: vtsp_timer_stop: 67475758

Jan 6 10:41:34.317: csm_vtsp_call_setup_resp (vdev_info=0x620BF874,

vtsp_cdb=0x621C5F3C)

Jan 6 10:41:34.317: csm_vtsp_call_setup_resp:vdev_common

BP TS allocatedat BP_stream0,

BP_Ch28

Jan 6 10:41:34.317: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat

stream 5, chan 3,BP_stream 0, BP_ch 28

Jan 6 10:41:34.317: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat

stream 5, chan 3,BP_stream 0, BP_ch 28vt sp_open_voice_and_set_params

Jan 6 10:41:34.317: dsp_close_voice_channel: [0:1 (54)] packet_Len=8 channel_id=8529

packet_id=75

Jan 6 10:41:34.317: dsp_open_voice_channel_20: [0:1 (54)] packet_Len=16

channel_id=8529

packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0 time_slot=0

serial_port=0

Jan 6 10:41:34.317: dsp_encap_config_20: [0:1 (54)] packet_Len=24 channel_id=8529

packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0

Jan 6 10:41:34.317: dsp_set_playout: [0:1 (54)] packet_Len=18 channel_id=8529

packet_id=76 mode=1 initial=60 min=4 max=200 fax_nom=300

Jan 6 10:41:34.317: dsp_echo_canceller_control: [0:1 (54)] packet_Len=10

channel_id=8529

packet_id=66 flags=0x0

Jan 6 10:41:34.317: dsp_set_gains: [0:1 (54)] packet_Len=12

channel_id=8529 packet_id=91

in_gain=0 out_gain=0

Jan 6 10:41:34.317: dsp_vad_enable: [0:1 (54)] packet_Len=10

channel_id=8529 packet_id=78

thresh=-38act_proceeding

Jan 6 10:41:34.321: csm_vtsp_call_proceeding:DST_tdm_chnl call.

BP TS allocatedstream 5,

chan 3,BP_stream 0, BP_ch 28act_alert

Jan 6 10:41:34.345: vtsp_ring_noan_timer_start: 67475761

Jan 6 10:41:34.345: csm_vtsp_call_alert (vtsp_cdb=0x621C5F3C)act_bridge act_caps_ind

Jan 6 10:41:34.589: act_caps_ind:Encap 1, Vad 2, Codec 0x4, CodecBytes 20,

FaxRate 2, FaxBytes 20 SignalType 0

DtmfRelay 1, Modem 1act_caps_ack

Jan 6 10:41:34.589: dsp_idle_mode: [0:1 (54)] packet_Len=8

channel_id=8529 packet_id=68

Jan 6 10:41:34.589: act_caps_ack: codec = 15, ret = 1

Jan 6 10:41:34.589: dsp_cp_tone_off: [0:1 (54)] packet_Len=8 channel_id=8529

packet_id=71

Jan 6 10:41:34.589: dsp_idle_mode: [0:1 (54)] packet_Len=8

channel_id=8529 packet_id=68

Jan 6 10:41:34.589: dsp_encap_config_20: [0:1 (54)] packet_Len=24 channel_id=8529

packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0

Jan 6 10:41:34.589: dsp_voice_mode: [0:1 (54)] packet_Len=24 channel_id=8529

packet_id=73 coding_type=20 voice_field_size=20 VAD_flag=1 echo_length=64

comfort_noise=1 inband_detect=1 digit_relay=2 AGC_flag=0act_alert_connect

Jan 6 10:41:36.857: vtsp_ring_noan_timer_stop: 67476012

Jan 6 10:41:36.857: dsp_cp_tone_off: [0:1 (54)] packet_Len=8 channel_id=8529

packet_id=71

Jan 6 10:41:36.857: csm_vtsp_call_connect (vtsp_cdb=0x621C5F3C,

voice_vdev=0x620BF874)

Jan 6 10:41:36.857: CSM_IC5_WAIT_FOR_SWITCH_OVER: CSM_EVENT_MODEM_OFFHOOK

at slot 2, port 16

Jan 6 10:41:36.917: CSM_RX_CAS_EVENT_FROM_NEAT:(0018):  EVENT_CHANNEL_CONNECTED

at slot 2 and port 16

Jan 6 10:41:36.917: CSM_PROC_IC6_WAIT_FOR_CONNECT: CSM_EVENT_DSX0_CONNECTED

at slot 2, port 16

Jan 6 10:41:36.921: from NEAT(0): (0/0): TX ANSWERED(ABCD=0101)

eefje#

R2 Digitale semi-compattato: Chiamata in arrivo a 567

Per una migliore comprensione dell'output del comando debug, consultare la teoria della segnalazione E1 R2.

eefje#show debug

CAS:

Channel Associated Signaling debugging is on

CSM Voice:

Voice Call Switching Module debugging is on

Voice Telephony session debugging is on

Voice Telephony dsp debugging is on

Voice Telephony error debugging is on

eefje#

eefje#

eefje#

Jan  6 09:53:42.389: from NEAT(0): (0/2): Rx SEIZURE(ABCD=0001)

Jan 6 09:53:42.433: VDEV_ALLOCATE: failed to allocate a device

Jan 6 09:53:42.433: VDEV_ALLOCATE: 1/27 is allocated

Jan 6 09:53:42.433: csm_vtsp_init_tdm (voice_vdev=0x620BF320)

Jan 6 09:53:42.433: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm slot 2, dspm 1,

dsp 4, dsp_channel 4

Jan 6 09:53:42.433: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm stream 7, channel 0,

bank 4, BP_channel 3, BP_stream 255

Jan 6 09:53:42.433: CSM_RX_CAS_EVENT_FROM_NEAT:(cid0017): EVENT_CALL_DIAL_IN

at slot 2 and port 15

Jan 6 09:53:42.433: CSM_PROC_IDLE: CSM_EVENT_START_DIGIT_COLLECT

at slot 2, port 15

Jan 6 09:53:42.433: csm_vtsp_start_digit_collect (voice_vdev=0x620BF320)

Jan 6 09:53:42.433:  Enter csm_connect_pri_vdev function

Jan 6 09:53:42.433: csm_connect_pri_vdev:tdm_allocate_BP_Ts()call. BP TS allocated

at BP_stream0, BP_Ch27,vdev_common 0x6 20BF390

Jan 6 09:53:42.433: to NEAT:(cid0017) EVENT_CHANNEL_LOCK for slot0 ctlr0 chan2

Jan 6 09:53:42.433: vtsp_do_call_setup_ind

Jan 6 09:53:42.433: vtsp_do_call_setup_ind: Call ID=65675, guid=61FAF610

Jan 6 09:53:42.433: vtsp_do_call_setup_ind: type=0, under_spec=0, name=, id0=0,

id1=0, id2=0, calling=, called=

Jan 6 09:53:42.433: vtsp_do_call_setup_ind: redirect DN = reason =

0vtsp_open_voice_and_set_params

Jan 6 09:53:42.433: dsp_close_voice_channel: [0:1:2] packet_Len=8 channel_id=8516

packet_id=75

Jan 6 09:53:42.433: dsp_open_voice_channel_20: [0:1:2] packet_Len=16

channel_id=8516

packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0

time_slot=1 serial_port=1

Jan 6 09:53:42.433: dsp_encap_config_20: [0:1:2] packet_Len=24 channel_id=8516

packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0

Jan 6 09:53:42.433: dsp_set_playout: [0:1:2] packet_Len=18 channel_id=8516

packet_id=76 mode=1 initial=60 min=4 max=200 fax_nom=300

Jan 6 09:53:42.433: dsp_echo_canceller_control: [0:1:2]

packet_Len=10 channel_id=8516

packet_id=66 flags=0x0

Jan 6 09:53:42.437: dsp_set_gains:[0:1:2] packet_Len=12

channel_id=8516 packet_id=91

in_gain=0 out_gain=0

Jan 6 09:53:42.437: dsp_vad_enable: [0:1:2] packet_Len=10 channel_id=8516

packet_id=78 thresh=-38

Jan 6 09:53:42.437: dsp_voice_mode: [0:1:2] packet_Len=24 channel_id=8516

packet_id=73 coding_type=1 voice_field_size=80 VAD_flag=0 echo_length=64

comfort_noise=1 inband_detect=1 digit_relay=2 AGC_flag=0vtsp_do_r2_start_digit():

dsp_dtmf_mode() dsp_dtmf_mode(VTSP_TONE_R2_MF_FORWARD_MODE)

Jan 6 09:53:42.437: dsp_dtmf_mode: [0:1:2] packet_Len=10 channel_id=8516

packet_id=65 dtmf_or_mf=1vtsp_do_r2_start_digit(): fsm_push(vtsp_r2_state_table)

Jan 6 09:53:42.437: csm_vtsp_call_setup_resp (vdev_info=0x620BF320,

vtsp_cdb=0x621C5F3C)

Jan 6 09:53:42.437: csm_vtsp_call_setup_resp:vdev_common BP

TS allocatedat BP_stream0,

BP_Ch27

Jan 6 09:53:42.437: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat

stream 7, chan 0,BP_stream 255, BP_ch 3

Jan 6 09:53:42.437: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat

stream 7, chan 0,BP_stream 0, BP_ch 27

Jan 6 09:53:42.437: CSM_PROC_IC1_COLLECT_ADDR_INFO: CSM_EVENT_MODEM_OFFHOOK

(DNIS=, ANI=) at slot 2, port 15

Jan 6 09:53:42.437: R2 Incoming Voice(2/15): DSX (E1 0:2): STATE:R2_IN_IDLE R2

Got Event R2_START

Jan 6 09:53:42.533: CSM_RX_CAS_EVENT_FROM_NEAT:(0017):EVENT_START_RX_TONE

at slot 2 and port 15

Jan 6 09:53:42.533: from NEAT(0): (0/2): TX SEIZURE_ACK (ABCD=1101)

!--- Digit 5 is sent: Forward Signal Group I-5.

Jan 6 09:53:42.641: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN:

digit=5, rtp_timestamp=0x9330B42B dc_digit_up

Jan 6 09:53:42.641: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C) received digit (5)

Jan 6 09:53:42.641: CSM voice (2/15): Rcvd Digit detected(5)

Jan 6 09:53:42.641: R2 Incoming Voice(2/15): DSX (E1 0:2):

STATE:R2_IN_COLLECT_DNIS R2

Got Event 5

!--- Digit 1 sent (pulse): Backward Signal Group A-1 (Send next digit) !--- "#" this indicates that it is a pulse).

Jan 6 09:53:42.641: vtsp_r2_generate_digits: vdev_common=0x620BF390,

string=5dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1#

Jan 6 09:53:42.641: dsp_dtmf_dialing: [0:1:2] packet_Len=36 channel_id=8516

packet_id=90 string=1# digits=2, time_on=150, time_off=30

Jan 6 09:53:42.641:    digit=`, components=2, freq_of_first=1020,

freq_of_second=1140,

amp_of_first=8192, amp_of_second=8192

Jan 6 09:53:42.641:    digit=o, components=2, freq_of_first=0, freq_of_second=0,

amp_of_first=1, amp_of_second=1

Jan 6 09:53:42.741: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=5,

duration=8291dc_digit

Jan 6 09:53:42.741: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C) received digit (5)

Jan 6 09:53:42.741: CSM voice (2/15): Rcvd Digit detected(5)

Jan 6 09:53:42.741: R2 Incoming Voice(2/15): DSX (E1 0:2):

STATE:R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_OFF

!--- Digit 6 is sent: Forward Signal Group I.

Jan 6 09:53:42.881: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN:

digit=6, rtp_timestamp=0x9330B42B dc_digit_up

Jan 6 09:53:42.881: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C)received digit (6)

Jan 6 09:53:42.881: CSM voice (2/15): Rcvd Digit detected(6)

Jan 6 09:53:42.881: R2 Incoming Voice(2/15): DSX (E1 0:2):

STATE:R2_IN_COLLECT_DNIS R2

Got Event 6

!--- Digit 1 sent (pulse): Backward Signal Group A-1. (Send next digit.)

Jan 6 09:53:42.881: vtsp_r2_generate_digits: vdev_common=0x620BF390,

string=56dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1#

Jan 6 09:53:42.881: dsp_dtmf_dialing: [0:1:2] packet_Len=36 channel_id=8516

packet_id=90 string=1# digits=2, time_on=150, time_off=30

Jan 6 09:53:42.881:    digit=`, components=2, freq_of_first=1020,

freq_of_second=1140,

amp_of_first=8192, amp_of_second=8192

Jan 6 09:53:42.881:    digit=o, components=2, freq_of_first=0, freq_of_second=0,

amp_of_first=1, amp_of_second=1

Jan 6 09:53:42.981: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=6,

duration=8291dc_digit

Jan 6 09:53:42.981: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C) received digit (6)

Jan 6 09:53:42.981: CSM voice (2/15): Rcvd Digit detected(6)

Jan 6 09:53:42.981: R2 Incoming Voice(2/15): DSX (E1 0:2):

STATE:R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_OFF

!--- Digit 7 is sent: Forward Signal Group I-7.

Jan 6 09:53:43.121: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN:

digit=7, rtp_timestamp=0x9330B42B dc_digit_up

Jan 6 09:53:43.121: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C)received digit (7)

Jan 6 09:53:43.121: CSM voice (2/15): Rcvd Digit detected(7)

Jan 6 09:53:43.121: R2 Incoming Voice(2/15): DSX (E1 0:2):

STATE:R2_IN_COLLECT_DNIS R2

Got Event 7

!--- Send digit 1 (pulse): Backward Signal Group A-1.

Jan 6 09:53:43.121: vtsp_r2_generate_digits: vdev_common=0x620BF390,

string=567dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1#

Jan 6 09:53:43.121: dsp_dtmf_dialing: [0:1:2] packet_Len=36 channel_id=8516

packet_id=90 string=1# digits=2, time_on=150, time_off=30

Jan 6 09:53:43.121:    digit=`, components=2, freq_of_first=1020,

freq_of_second=1140,

amp_of_first=8192, amp_of_second=8192

Jan 6 09:53:43.121:    digit=o, components=2, freq_of_first=0, freq_of_second=0,

amp_of_first=1, amp_of_second=1

Jan 6 09:53:43.221: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=7,

duration=8291dc_digit

Jan 6 09:53:43.221: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C) received digit (7)

Jan 6 09:53:43.221: CSM voice (2/15): Rcvd Digit detected(7)

Jan 6 09:53:43.221: R2 Incoming Voice(2/15): DSX (E1 0:2):

STATE:R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_OFF

Jan 6 09:53:43.489: vtsp_process_dsp_message: MSG_TX_DIALING_DONEdc_dialing_done()

!--- Timeout is 3 seconds.

Jan 6 09:53:46.121: R2 Incoming Voice(2/15): DSX (E1 0:2):

STATE:R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_TIMER

!--- Digit 3 sent(pulse): Backward Signal Group A-3. !--- (Address-complete, changeover to reception of Group-B signals).

Jan 6 09:53:46.121: vtsp_r2_generate_digits: vdev_common=0x620BF390,

string=567dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 3#

Jan 6 09:53:46.121: dsp_dtmf_dialing: [0:1:2] packet_Len=36 channel_id=8516

packet_id=90 string=3# digits=2, time_on=150, time_off=30

Jan 6 09:53:46.121:    digit=b, components=2, freq_of_first=1020,

freq_of_second=900,

amp_of_first=8192, amp_of_second=8192

Jan 6 09:53:46.121:    digit=o, components=2, freq_of_first=0,

freq_of_second=0, amp_of_first=1, amp_of_second=1

!--- Digit 1 is sent: Forward Signal Group II-1 !--- (subscriber without priority).

Jan 6 09:53:46.361: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN:

digit=1, rtp_timestamp=0x9330B42B dc_digit_up

Jan 6 09:53:46.361: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C)

received digit (1)

Jan 6 09:53:46.361: CSM voice (2/15): Rcvd Digit detected(1)

Jan 6 09:53:46.361: R2 Incoming Voice(2/15): DSX (E1 0:2):

STATE:R2_IN_CATEGORY R2

Got Event 1

Jan 6 09:53:46.361:  r2_comp_category:R2_ALERTING

!--- Digit 6 sent (pulse): Backward Signal Group B-6 !--- (the subscriber line free of charge).

Jan 6 09:53:46.361: vtsp_r2_generate_digits: vdev_common=0x620BF390,

string=567dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 6#

Jan  6 09:53:46.361: dsp_dtmf_dialing: [0:1:2] packet_Len=36 channel_id=8516

packet_id=90 string=6# digits=2, time_on=150, time_off=30

Jan 6 09:53:46.361:    digit=e, components=2, freq_of_first=900,

freq_of_second=780,

amp_of_first=8192, amp_of_second=8192

Jan 6 09:53:46.361:    digit=o, components=2, freq_of_first=0, freq_of_second=0,

amp_of_first=1, amp_of_second=1

Jan 6 09:53:46.461: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF:digit=1,

duration=8291dc_digit

Jan 6 09:53:46.461: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C)received digit (1)

Jan 6 09:53:46.461: CSM voice (2/15): Rcvd Digit detected(1)

Jan 6 09:53:46.461: R2 Incoming Voice(2/15): DSX (E1 0:2): STATE:R2_IN_COMPLETE R2

Got Event R2_TONE_OFF

Jan 6 09:53:46.729: vtsp_process_dsp_message: MSG_TX_DIALING_DONEdc_dialing_done()

Jan 6 09:53:47.461: R2 Incoming Voice(2/15): DSX (E1 0:2):

STATE:R2_IN_WAIT_GUARD R2

Got Event R2_TONE_TIMER

Jan 6 09:53:47.461:  R2_IN_IDLE:2 r2_in_connect called

Jan 6 09:53:47.461: CSM_PROC_IC1_COLLECT_ADDR_INFO: CSM_EVENT_ADDR_INFO_COLLECTED

(DNIS=567, ANI=) at slot 2, port 15

Jan 6 09:53:47.461: vtsp_tsp_call_accept_check (sdb=0x61B8F0E0,calling_number=

called_number=567): peer_tag=0

Jan 6 09:53:47.461: VDEV_ALLOCATE: failed to allocate a device

Jan 6 09:53:47.461: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem

Jan 6 09:53:47.461: VDEV_ALLOCATE: failed to allocate a device

Jan 6 09:53:47.461: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem

Jan 6 09:53:47.461: VDEV_ALLOCATE: failed to allocate a device

Jan 6 09:53:47.461: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem

Jan 6 09:53:47.461: CSM_PROC_IC3_WAIT_FOR_RES_RESP: CSM_EVENT_RESOURCE_OK at slot 2,

port 15

Jan 6 09:53:47.461: vtsp_IC_switch : (voice_vdev= 0x620BF320)

Jan 6 09:53:47.461: vtsp_tsp_call_switch_ind (cdb=0x621C5F3C,tsp_info=0x620BF320,

calling_number= called_number=567 redirect_number=):

peer_tag=123dc_switch: fsm_pop()

Jan 6 09:53:47.461: vtsp_do_call_setup_ind

Jan 6 09:53:47.461: vtsp_do_call_setup_ind: Call ID=65677, guid=61FAF610

Jan 6 09:53:47.461: vtsp_do_call_setup_ind: type=0, under_spec=0, name=AB^Lo, id0=3,

id1=0, id2=0, calling=123, called=567

Jan 6 09:53:47.465: dsp_cp_tone_off: [] packet_Len=8 channel_id=8516 packet_id=71

Jan 6 09:53:47.465: dsp_idle_mode: [] packet_Len=8 channel_id=8516 packet_id=68

Jan 6 09:53:47.465: dsp_close_voice_channel: [] packet_Len=8 channel_id=8516

packet_id=75

Jan 6 09:53:47.465: vtsp_timer_stop: 67189073

Jan 6 09:53:47.465: csm_vtsp_call_setup_resp (vdev_info=0x620BF320,

vtsp_cdb=0x621C5F3C)

Jan 6 09:53:47.465: csm_vtsp_call_setup_resp:vdev_common

BP TS allocatedat BP_stream0,

BP_Ch27

Jan 6 09:53:47.465: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat

stream 7, chan 0,BP_stream 0, BP_ch 27

Jan 6 09:53:47.465: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat

stream 7, chan 0,BP_stream 0, BP_ch 27vtsp_open_voice_and_set_params

Jan 6 09:53:47.465: dsp_close_voice_channel: [0:1 (52)] packet_Len=8 channel_id=8516

packet_id=75

Jan 6 09:53:47.465: dsp_open_voice_channel_20: [0:1 (52)]

packet_Len=16 channel_id=8516

packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0

time_slot=1 serial_port=1

Jan 6 09:53:47.465: dsp_encap_config_20: [0:1 (52)] packet_Len=24

channel_id=8516

packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0

Jan 6 09:53:47.465: dsp_set_playout: [0:1 (52)] packet_Len=18 channel_id=8516

packet_id=76 mode=1 initial=60 min=4 max=200  fax_nom=300

Jan& 6 09:53:47.465: dsp_echo_canceller_control: [0:1 (52)] packet_Len=10

channel_id=8516

packet_id=66 flags=0x0

Jan 6 09:53:47.465: dsp_set_gains: [0:1 (52)] packet_Len=12 channel_id=8516

packet_id=91 in_gain=0 out_gain=0

Jan 6 09:53:47.465: dsp_vad_enable: [0:1 (52)] packet_Len=10 channel_id=8516

packet_id=78 thresh=-38act_proceeding

Jan 6 09:53:47.469: csm_vtsp_call_proceeding:DST_tdm_chnl call. BP TS

allocatedstream 7,

chan 0,BP_stream 0, BP_ch 27act_alert

Jan 6 09:53:47.493: vtsp_ring_noan_timer_start: 67189076

Jan 6 09:53:47.493: csm_vtsp_call_alert (vtsp_cdb=0x621C5F3C)

act_bridge act_caps_ind

Jan 6 09:53:47.737: act_caps_ind:Encap 1, Vad 2, Codec 0x4, CodecBytes 20,

FaxRate 2, FaxBytes 20 SignalType 0

DtmfRelay 1, Modem 1act_caps_ack

Jan 6 09:53:47.737: dsp_idle_mode: [0:1 (52)] packet_Len=8 channel_id=8516

packet_id=68

Jan 6 09:53:47.737: act_caps_ack: codec = 15, ret = 1

Jan 6 09:53:47.737: dsp_cp_tone_off: [0:1 (52)] packet_Len=8 channel_id=8516

packet_id=71

Jan 6 09:53:47.737: dsp_idle_mode: [0:1 (52)] packet_Len=8 channel_id=8516

packet_id=68

Jan 6 09:53:47.737: dsp_encap_config_20: [0:1 (52)] packet_Len=24 channel_id=8516

packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0

Jan 6 09:53:47.737: dsp_voice_mode: [0:1 (52)] packet_Len=24 channel_id=8516

packet_id=73 coding_type=20 voice_field_size= 20 VAD_flag=1 echo_length=64

comfort_noise=1 inband_detect=1 digit_relay=2 AGC_flag=0act_alert_connect

Jan 6 09:53:49.461: vtsp_ring_noan_timer_stop: 67189273

Jan 6 09:53:49.461: dsp_cp_tone_off: [0:1 (52)] packet_Len=8 channel_id=8516

packet_id=71

Jan 6 09:53:49.461: csm_vtsp_call_connect (vtsp_cdb=0x621C5F3C,

voice_vdev=0x620BF320)

Jan 6 09:53:49.461: CSM_IC5_WAIT_FOR_SWITCH_OVER: CSM_EVENT_MODEM_OFFHOOK

at slot 2, port 15

Jan 6 09:53:49.617: CSM_RX_CAS_EVENT_FROM_NEAT:(0017):  EVENT_CHANNEL_CONNECTED

at slot 2 and port 15

Jan 6 09:53:49.617: CSM_PROC_IC6_WAIT_FOR_CONNECT: CSM_EVENT_DSX0_CONNECTED

at slot 2, port 15

Jan 6 09:53:49.621: from NEAT(0): (0/2): TX ANSWERED(ABCD=0101)

eefje#

eefje#

R2 Impulso digitale ANI: Chiamata in arrivo a 567

Per una migliore comprensione dell'output del comando debug, consultare la teoria della segnalazione E1 R2.

eefje#debug csm voice

Voice Call Switching Module debugging is on

eefje#debug cas

Channel Associated Signaling debugging is on

Jan 7 10:00:02.907: from NEAT(0): debug-cas is on

Jan 7 10:00:02.907: from NEAT(0): special debug-cas is offg vtsp all

Voice telephony call control all debugging is on

eefje#

eefje#

Jan 7 10:00:23.883: from NEAT(0): (0/8): Rx SEIZURE (ABCD=0001)

Jan 7 10:00:23.927: VDEV_ALLOCATE: failed to allocate a device

Jan 7 10:00:23.927: VDEV_ALLOCATE: 1/2 is allocated

Jan 7 10:00:23.927: csm_vtsp_init_tdm (voice_vdev=0x61F19688)

Jan 7 10:00:23.927: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm slot 1,

dspm 3, dsp 4,

dsp_channel 1

Jan 7 10:00:23.927: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm stream 5,

channel 13,

bank 0, BP_channel 15, BP_stream 255

Jan 7 10:00:23.927: CSM_RX_CAS_EVENT_FROM_NEAT:(cid0007):

EVENT_CALL_DIAL_IN at slot 1

and port 60

Jan 7 10:00:23.927: CSM_PROC_IDLE: CSM_EVENT_START_DIGIT_COLLECT at slot 1, port 60

Jan 7 10:00:23.927: csm_vtsp_start_digit_collect (voice_vdev=0x61F19688)

Jan 7 10:00:23.927:  Enter csm_connect_pri_vdev function

Jan 7 10:00:23.927: csm_connect_pri_vdev:tdm_allocate_BP_Ts() call. BP

TS allocated at BP_stream0, BP_Ch8,vdev_common 0x6205E5F8

Jan 7 10:00:23.927: to NEAT:(cid0007) EVENT_CHANNEL_LOCK for slot0 ctlr0 chan8

Jan 7 10:00:23.927: vtsp_do_call_setup_ind

Jan 7 10:00:23.927: vtsp_do_call_setup_ind: Call ID=65579, guid=62031A88

Jan 7 10:00:23.927: vtsp_do_call_setup_ind: type=0, under_spec=0,

name=, id0=0, id1=0,id2=0, calling=, called=

Jan 7 10:00:23.927: vtsp_do_call_setup_ind: redirect DN =  reason =

0vtsp_do_r2_start_digit(): fsm_push(vtsp_r2_state_table)

Jan 7 10:00:23.927: csm_vtsp_call_setup_resp (vdev_info=0x61F19688,

vtsp_cdb=0x61B5BFF8)

Jan 7 10:00:23.927: csm_vtsp_call_setup_resp:vdev_common

BP TS allocatedat BP_stream0,

BP_Ch8

Jan 7 10:00:23.927: csm_vtsp_call_setup_resp:DST_tdm_chnl call.

BP TS allocatedat stream

5, chan 13,BP_stream 255, BP_ch 15

Jan 7 10:00:23.927: csm_vtsp_call_setup_resp:DST_tdm_chnl call.

BP TS allocatedat stream

5, chan 13,BP_stream 0, BP_ch 8

Jan 7 10:00:23.927: CSM_PROC_IC1_COLLECT_ADDR_INFO: CSM_EVENT_MODEM_OFFHOOK

(DNIS=, ANI=) at slot 1, port 60

Jan 7 10:00:23.931: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE: R2_IN_IDLE

R2 Got Event R2_START

Jan 7 10:00:24.027: CSM_RX_CAS_EVENT_FROM_NEAT:(0007):  EVENT_START_RX_TONE

at slot 1 and port 60

Jan 7 10:00:24.027: from NEAT(0): (0/8): TX SEIZURE_ACK

(ABCD=1101)dc_init_dsp

vtsp_open_voice_and_set_params

Jan 7 10:00:24.151: dsp_close_voice_channel: [0:1:8] packet_Len=8 channel_id=4929

packet_id=75

Jan 7 10:00:24.151: dsp_open_voice_channel_20: [0:1:8] packet_Len=16

channel_id=4929

packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0

time_slot=0 serial_port=0

Jan 7 10:00:24.151: dsp_encap_config_20: [0:1:8] packet_Len=24 channel_id=4929

packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0

Jan 7 10:00:24.151: dsp_set_playout: [0:1:8] packet_Len=18 channel_id=4929

packet_id=76 mode=1 initial=60 min=4 max=200 fax_nom=300

Jan 7 10:00:24.151: dsp_echo_canceller_control: [0:1:8]

packet_Len=10 channel_id=4929

packet_id=66 flags=0x0

Jan 7 10:00:24.151: dsp_set_gains: [0:1:8] packet_Len=12

channel_id=4929 packet_id=91

in_gain=0 out_gain=0

Jan 7 10:00:24.151: dsp_vad_enable: [0:1:8] packet_Len=10

channel_id=4929 packet_id=78

thresh=-38

Jan 7 10:00:24.151: dsp_voice_mode: [0:1:8] packet_Len=24

channel_id=4929 packet_id=73

coding_type=1 voice_field_size=80 VAD_flag=0 echo_length=64

comfort_noise=1

inband_detect=1 digit_relay=2 AGC_flag=0dsp_dtmf_mode

(VTSP_TONE_R2_MF_FORWARD_MODE)

Jan 7 10:00:24.151: dsp_dtmf_mode: [0:1:8] packet_Len=10 channel_id=4929

packet_id=65dtmf_or_mf=1

!--- Digit 5 is sent: Forward Signal Group I-5 (First DNIS digit).

Jan 7 10:00:24.203: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=5,

rtp_timestamp=0x04030000 dc_digit_up

Jan 7 10:00:24.203: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)received digit (5)

Jan 7 10:00:24.203: CSM voice (1/60): Rcvd Digit detected(5)

Jan 7 10:00:24.203: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_PRE_CALLERID R2

Got Event 5

!--- Send Backward Signal Group A-5 (caller category request).

Jan 7 10:00:24.203: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 5

Jan 7 10:00:24.203: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929packet_id=90

string=5 digits=1, time_on=65435, time_off=30

Jan 7 10:00:24.203:    digit=, components=2, freq_of_first=1020,

freq_of_second=780,

amp_of_first=8192, amp_of_second=8192

Jan 7 10:00:24.303: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF:digit=5,

duration=30dc_digit

Jan 7 10:00:24.303: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (5)

Jan 7 10:00:24.303: CSM voice (1/60): Rcvd Digit detected(5)

Jan 7 10:00:24.303: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_CALLERID R2

Got Event R2_TONE_OFF

Jan 7 10:00:24.303: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #

Jan 7 10:00:24.303: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929

packet_id=90 string=# digits=1, time_on=150, time_off=30

Jan 7 10:00:24.303:    digit=, components=2, freq_of_first=0, freq_of_second=0,

amp_of_first=1, amp_of_second=1

!--- Caller Category Forward Signal Group II-1 is sent.

Jan 7 10:00:24.403: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=1,

rtp_timestamp=0x001E0010 dc_digit_up

Jan 7 10:00:24.403: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)received

digit (1)

Jan 7 10:00:24.403: CSM voice (1/60): Rcvd Digit detected(1)

Jan 7 10:00:24.403: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE:R2_IN_CALLERID R2

Got Event 1

!--- Send Backward Signal Group A-5 (Caller ID request).

Jan 7 10:00:24.403: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 5

Jan 7 10:00:24.403: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=5 digits=1, time_on=65435, time_off=30

Jan 7 10:00:24.403:    digit=, components=2, freq_of_first=1020, freq_of_second=780,

amp_of_first=8192, amp_of_second=8192

Jan 7 10:00:24.503: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=1,

duration=30dc_digit

Jan 7 10:00:24.503: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (1)

Jan 7 10:00:24.503: CSM voice (1/60): Rcvd Digit detected(1)

Jan 7 10:00:24.503: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_CALLERID R2

Got Event R2_TONE_OFF

Jan 7 10:00:24.503: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #

Jan 7 10:00:24.503: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=# digits=1, time_on=150, time_off=30

Jan 7 10:00:24.503:    digit=, components=2, freq_of_first=0, freq_of_second=0,

amp_of_first=1, amp_of_second=1

!--- First ANI digit is sent: Forward Signal Group I-1.

Jan  7 10:00:24.603: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN:

digit=1, rtp_timestamp=0x001E0010 dc_digit_up

Jan 7 10:00:24.603: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8) received digit (1)

Jan 7 10:00:24.603: CSM voice (1/60): Rcvd Digit detected(1)

Jan 7 10:00:24.603: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_CALLERID R2

Got Event 1

!--- Send Backward Signal Group A-5 (Caller ID request).

Jan 7 10:00:24.603: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 5

Jan 7 10:00:24.603: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=5 digits=1, time_on=65435, time_off=30

Jan 7 10:00:24.603:    digit=, components=2, freq_of_first=1020,

freq_of_second=780,

amp_of_first=8192, amp_of_second=8192

Jan 7 10:00:24.703: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=1,

duration=30dc_digit

Jan 7 10:00:24.703: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (1)

Jan 7 10:00:24.703: CSM voice (1/60): Rcvd Digit detected(1)

Jan 7 10:00:24.703: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_CALLERID R2

Got Event R2_TONE_OFF

Jan 7 10:00:24.703: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #

Jan 7 10:00:24.703: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=# digits=1, time_on=150, time_off=30

Jan 7 10:00:24.703:    digit=, components=2, freq_of_first=0, freq_of_second=0,

amp_of_first=1, amp_of_second=1

!--- Second ANI digit is sent: Forward Signal Group I-2.

Jan 7 10:00:24.803: vtsp_process_dsp_message:

MSG_TX_DTMF_DIGIT_BEGIN:digit=2,

rtp_timestamp=0x001E0010 dc_digit_up

Jan 7 10:00:24.803: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)

received digit (2)

Jan 7 10:00:24.803: CSM voice (1/60): Rcvd Digit detected(2)

Jan 7 10:00:24.803: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_CALLERID R2

Got Event 2

!--- Send Backward Signal Group A-5 (Caller ID request).

Jan 7 10:00:24.803: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 5

Jan 7 10:00:24.803: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929packet_id=90

string=5 digits=1, time_on=65435, time_off=30

Jan 7 10:00:24.803:    digit=, components=2, freq_of_first=1020,

freq_of_second=780,

amp_of_first=8192, amp_of_second=8192

Jan 7 10:00:24.903: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=2,

duration=30dc_digit

Jan 7 10:00:24.903: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (2)

Jan 7 10:00:24.903: CSM voice (1/60): Rcvd Digit detected(2)

Jan 7 10:00:24.903: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_CALLERID

R2 Got Event R2_TONE_OFF

Jan 7 10:00:24.903: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #

Jan 7 10:00:24.903: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=# digits=1, time_on=150, time_off=30

Jan 7 10:00:24.903:    digit=, components=2, freq_of_first=0,

freq_of_second=0,

amp_of_first=1, amp_of_second=1

!--- Third ANI digit is sent: Forward Signal Group I-3.

Jan 7 10:00:25.003: vtsp_process_dsp_message:

MSG_TX_DTMF_DIGIT_BEGIN: digit=3,

rtp_timestamp=0x001E0010 dc_digit_up

Jan 7 10:00:25.003: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)

received digit (3)

Jan 7 10:00:25.003: CSM voice (1/60): Rcvd Digit detected(3)

Jan 7 10:00:25.003: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_CALLERID R2

Got Event 3

!--- Send Backward Signal Group A-5 (Caller ID request).

Jan 7 10:00:25.003: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 5

Jan 7 10:00:25.003: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=5 digits=1, time_on=65435, time_off=30

Jan 7 10:00:25.003:    digit=, components=2, freq_of_first=1020,

freq_of_second=780,

amp_of_first=8192, amp_of_second=8192

Jan 7 10:00:25.103: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF:digit=3,

duration=30dc_digit

Jan 7 10:00:25.103: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (3)

Jan 7 10:00:25.103: CSM voice (1/60): Rcvd Digit detected(3)

Jan 7 10:00:25.103: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_CALLERID R2

Got Event R2_TONE_OFF

Jan 7 10:00:25.103: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #

Jan 7 10:00:25.103: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=# digits=1, time_on=150, time_off=30

Jan 7 10:00:25.103:    digit=, components=2, freq_of_first=0,

freq_of_second=0,

amp_of_first=1, amp_of_second=1

!--- Digit 15 is sent: Forward Signal Group I-15 (end of ANI digit).

Jan 7 10:00:25.203: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN:

digit=15,

rtp_timestamp=0x001E0010 dc_digit_up

Jan 7 10:00:25.203: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)

received digit (*)

Jan 7 10:00:25.203: CSM voice (1/60): Rcvd Digit detected(*)

Jan 7 10:00:25.203: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_CALLERID R2

Got Event 15

!--- Send Backward Signal Group A-1 (next DNIS digit).

Jan 7 10:00:25.203: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1

Jan 7 10:00:25.203: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=1 digits=1, time_on=65435, time_off=30

Jan 7 10:00:25.203:    digit=, components=2, freq_of_first=1020,

freq_of_second=1140,

amp_of_first=8192, amp_of_second=8192

Jan 7 10:00:25.303: vtsp_process_dsp_message:

MSG_TX_DTMF_DIGIT_OFF: digit=15,

duration=30dc_digit

Jan 7 10:00:25.303: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (*)

Jan 7 10:00:25.303: CSM voice (1/60): Rcvd Digit detected(*)

Jan 7 10:00:25.303: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_OFF

Jan 7 10:00:25.303: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #

Jan 7 10:00:25.303: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929

packet_id=90 string=# digits=1, time_on=150, time_off=30

Jan 7 10:00:25.303:    digit=, components=2, freq_of_first=0, freq_of_second=0,

amp_of_first=1, amp_of_second=1

!--- Second DNIS digit is sent: Forward Signal Group I-6.

Jan  7 10:00:25.391: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=6,

rtp_timestamp=0x001E0010 dc_digit_up

Jan 7 10:00:25.391: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)

received digit (6)

Jan 7 10:00:25.391: CSM voice (1/60): Rcvd Digit detected(6)

Jan 7 10:00:25.391: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_COLLECT_DNIS

R2 Got Event 6

!--- Send Backward Signal Group A-1.

Jan 7 10:00:25.391: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=56dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1

Jan 7 10:00:25.391: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=1 digits=1, time_on=65435, time_off=30

Jan 7 10:00:25.391:    digit=, components=2, freq_of_first=1020,

freq_of_second=1140,

amp_of_first=8192, amp_of_second=8192

Jan 7 10:00:25.491: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF:digit=6,

duration=30dc_digit

Jan 7 10:00:25.491: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (6)

Jan 7 10:00:25.491: CSM voice (1/60): Rcvd Digit detected(6)

Jan 7 10:00:25.491: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE: R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_OFF

Jan 7 10:00:25.491: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=56dc_dial() vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #

Jan 7 10:00:25.491: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=# digits=1, time_on=150, time_off=30

Jan 7 10:00:25.491:    digit=, components=2, freq_of_first=0,

freq_of_second=0,

amp_of_first=1, amp_of_second=1

!--- Third DNIS digit is sent: Forward Signal Group I-7.

Jan 7 10:00:25.583: vtsp_process_dsp_message:

MSG_TX_DTMF_DIGIT_BEGIN: digit=7,

rtp_timestamp=0x001E0010 dc_digit_up

Jan 7 10:00:25.583: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)

received digit (7)

Jan 7 10:00:25.583: CSM voice (1/60): Rcvd Digit detected(7)

Jan 7 10:00:25.583: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_COLLECT_DNIS R2

Got Event 7

!--- Send Backward Signal Group A-1.

Jan 7 10:00:25.583: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=567dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1

Jan 7 10:00:25.583: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=1 digits=1, time_on=65435, time_off=30

Jan 7 10:00:25.583:    digit=, components=2, freq_of_first=1020,

freq_of_second=1140,

amp_of_first=8192, amp_of_second=8192

Jan 7 10:00:25.683: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=7,

duration=30dc_digit

Jan 7 10:00:25.683: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8)

received digit (7)

Jan 7 10:00:25.683: CSM voice (1/60): Rcvd Digit detected(7)

Jan 7 10:00:25.683: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_OFF

Jan 7 10:00:25.683: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=567dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #

Jan 7 10:00:25.683: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=# digits=1, time_on=150, time_off=30

Jan 7 10:00:25.683:    digit=, components=2, freq_of_first=0,

freq_of_second=0,

amp_of_first=1, amp_of_second=1

Jan 7 10:00:25.835: vtsp_process_dsp_message: MSG_TX_DIALING_DONEdc_dialing_done()

!--- Timeout is 3 seconds.

Jan 7 10:00:28.583: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_TIMER

!--- Send Backward Signal Group A-3: address-complete, changeover !--- to reception of group-B signal.

Jan 7 10:00:28.583: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=567dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 3#

Jan 7 10:00:28.583: dsp_dtmf_dialing: [0:1:8] packet_Len=36

channel_id=4929 packet_id=90

string=3# digits=2, time_on=150, time_off=30

Jan 7 10:00:28.583:    digit=, components=2, freq_of_first=1020,

freq_of_second=900,

amp_of_first=8192, amp_of_second=8192

Jan 7 10:00:28.583:    digit=, components=2, freq_of_first=0, freq_of_second=0,

amp_of_first=1, amp_of_second=1

!--- Forward Signal Group II-1 is sent: subscriber without priority.

Jan 7 10:00:28.831: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=1,

rtp_timestamp=0x001E0003 dc_digit_up

Jan 7 10:00:28.831: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)

received digit (1)

Jan 7 10:00:28.831: CSM voice (1/60): Rcvd Digit detected(1)

Jan 7 10:00:28.831: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_CATEGORY R2

Got Event 1

Jan 7 10:00:28.831: CSM_PROC_IC1_COLLECT_ADDR_INFO:

CSM_EVENT_ADDR_INFO_COLLECTED

(DNIS=567, ANI=123) at slot 1, port 60

Jan 7 10:00:28.831: vtsp_tsp_call_accept_check (sdb=0x61DADEE0,

calling_number=123

called_number=567): peer_tag=0

Jan 7 10:00:28.835: VDEV_ALLOCATE: failed to allocate a device

Jan 7 10:00:28.835: VDEV_ALLOCATE_ALMOST_READY: failed to allocate

a non-idle modem

Jan 7 10:00:28.835: VDEV_ALLOCATE: failed to allocate a device

Jan 7 10:00:28.835: VDEV_ALLOCATE_ALMOST_READY: failed to allocate

a non-idle modem

Jan 7 10:00:28.835: VDEV_ALLOCATE: failed to allocate a device

Jan 7 10:00:28.835: VDEV_ALLOCATE_ALMOST_READY: failed to allocate

a non-idle modem

Jan 7 10:00:28.835: CSM_PROC_IC3_WAIT_FOR_RES_RESP: CSM_EVENT_RESOURCE_OK

at slot 1,

port 60

Jan 7 10:00:28.835: vtsp_IC_switch : (voice_vdev= 0x61F19688)

Jan 7 10:00:28.835: vtsp_tsp_call_switch_ind (cdb=0x61B5BFF8,

tsp_info=0x61F19688,

calling_number=123 called_number=567 redirect_number=):

peer_tag=123dc_switch: fsm_pop()

Jan 7 10:00:28.835: vtsp_do_call_setup_ind

Jan 7 10:00:28.835: vtsp_do_call_setup_ind: Call ID=65581,

guid=62031A88

Jan 7 10:00:28.835: vtsp_do_call_setup_ind: type=0, under_spec=0,

name=b`, id0=9,

id1=0, id2=0, calling=123, called=567

Jan 7 10:00:28.835: dsp_cp_tone_off: [] packet_Len=8 channel_id=4929

packet_id=71

Jan 7 10:00:28.835: dsp_idle_mode: [] packet_Len=8 channel_id=4929

packet_id=68

Jan 7 10:00:28.835: dsp_close_voice_channel: [] packet_Len=8

channel_id=4929 packet_id=75

Jan 7 10:00:28.835: vtsp_timer_stop: 7063006

Jan 7 10:00:28.839: csm_vtsp_call_setup_resp (vdev_info=0x61F19688,

vtsp_cdb=0x61B5BFF8)

Jan 7 10:00:28.839: csm_vtsp_call_setup_resp:vdev_common BP TS

allocatedat BP_stream0,

BP_Ch8

Jan 7 10:00:28.839: csm_vtsp_call_setup_resp:DST_tdm_chnl call.

BP TS allocatedat stream 5, chan 13,BP_stream 0, BP_ch 8

Jan 7 10:00:28.839: csm_vtsp_call_setup_resp:DST_tdm_chnl call.

BP TS allocatedat stream 5, chan 13,BP_stream 0, BP_ch

8vtsp_open_voice_and_set_params

Jan 7 10:00:28.839: dsp_close_voice_channel: [0:1 (17)]

packet_Len=8 channel_id=4929

packet_id=75

Jan 7 10:00:28.839: dsp_open_voice_channel_20: [0:1 (17)] packet_Len=16

channel_id=4929

packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0

time_slot=0 serial_port=0

Jan 7 10:00:28.839: dsp_encap_config_20: [0:1 (17)] packet_Len=24

channel_id=4929

packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0t_vpxcc=0x0

r_vpxcc=0x0

Jan 7 10:00:28.839: dsp_set_playout: [0:1 (17)] packet_Len=18

channel_id=4929 packet_id=76 mode=1 initial=60 min=4 max=200 fax_nom=300

Jan 7 10:00:28.839: dsp_echo_canceller_control: [0:1 (17)]

packet_Len=10 channel_id=4929

packet_id=66 flags=0x0

Jan 7 10:00:28.839: dsp_set_gains: [0:1 (17)] packet_Len=12

channel_id=4929 packet_id=91

in_gain=0 out_gain=0

Jan 7 10:00:28.839: dsp_vad_enable: [0:1 (17)] packet_Len=10

channel_id=4929 packet_id=78

thresh=-38act_proceeding

Jan 7 10:00:28.839: csm_vtsp_call_proceeding:DST_tdm_chnl call.

BP TS allocatedstream 5,

chan 13,BP_stream 0, BP_ch 8act_alert

Jan 7 10:00:28.867: vtsp_ring_noan_timer_start: 7063009

Jan 7 10:00:28.867: csm_vtsp_call_alert (vtsp_cdb=0x61B5BFF8)

Jan 7 10:00:28.867:  csm_vtsp_call_alert: CSM_EVENT_ALERTING_RECEIVED

Jan 7 10:00:28.867: CSM_IC5_WAIT_FOR_SWITCH_OVER:  at slot 1, port 60

Jan 7 10:00:28.867: CSM_EVENT_ALERTING_RECEIVED:

Jan 7 10:00:28.867:  calling alerting_start_event

!--- Note: For modems, Backward Signal !--- Group B-6 (subscriber's line free, charge) !--- is sent immediately. !--- For voice, it is delayed until alerting is received. !--- Notice that "R2_REJECT" is printed instead of R2_ALERTING. !--- This printing issue is solved in Cisco IOS Software Release 12.1T.

Jan 7 10:00:28.867: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_IDLE R2

Got Event R2_REJECT

Jan 7 10:00:28.867:  R2_ALERTING: r2_comp_idle

Jan 7 10:00:28.867: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=567act_bridge

Jan 7 10:00:28.867: dsp_voice_mode: [0:1 (17)] packet_Len=24

channel_id=4929 packet_id=73

coding_type=1 voice_field_size=80 VAD_flag=0 echo_length=64

comfort_noise=1

inband_detect=1 digit_relay=2 AGC_flag=0dsp_dtmf_mode

(VTSP_TONE_R2_MF_FORWARD_MODE)

!--- Answer signal (B-6) is sent after alerting is received. !--- Send Backward Signal Group B6 signal (Subscriber's line free, charge).

Jan 7 10:00:28.871: dsp_dtmf_mode: [0:1 (17)] packet_Len=10

channel_id=4929 packet_id=65

dtmf_or_mf=1vtsp_r2_dial vtsp_r2_dial(): fsm_push(vtsp_r2_state_table)

dsp_dtmf_dialing(): dial_string = 6

Jan 7 10:00:28.871: dsp_dtmf_dialing: [0:1 (17)] packet_Len=24

channel_id=4929

packet_id=90 string=6 digits=1, time_on=65435, time_off=30

Jan 7 10:00:28.871:    digit=, components=2, freq_of_first=900,

freq_of_second=780,

amp_of_first=8192, amp_of_second=8192

Jan 7 10:00:28.923: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=1,

rtp_timestamp=0x001E0006 dc_digit_up

Jan 7 10:00:28.923: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)

received digit (1)

Jan 7 10:00:28.923: CSM voice (1/60): Rcvd Digit detected(1)

Jan 7 10:00:28.923: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE: R2_IN_COMPLETE

R2 Got Event 1

Jan 7 10:00:28.971: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=1,

duration=30dc_digit

Jan 7 10:00:28.971: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8)

received digit (1)

Jan 7 10:00:28.971: CSM voice (1/60): Rcvd Digit detected(1)

Jan 7 10:00:28.971: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE: R2_IN_COMPLETE R2

Got Event R2_TONE_OFF

Jan 7 10:00:28.971: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=567dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #

Jan 7 10:00:28.971: dsp_dtmf_dialing: [0:1 (17)] packet_Len=24

channel_id=4929

packet_id=90 string=# digits=1, time_on=150, time_off=30

Jan 7 10:00:28.975:    digit=, components=2, freq_of_first=0,

freq_of_second=0,

amp_of_first=1, amp_of_second=1ds_dialing_defaultds_dialing_default

Jan 7 10:00:29.127: vtsp_process_dsp_message:

MSG_TX_DIALING_DONEdc_dialing_done()

Jan 7 10:00:29.971: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE: R2_IN_WAIT_GUARD R2

Got Event R2_TONE_TIMER

Jan 7 10:00:29.971:  R2_IN_IDLE:2 r2_in_connect called

Jan 7 10:00:29.971: R2_IN_CONNECT: call end dial

Jan 7 10:00:29.971:  pop the dial state machine

Jan 7 10:00:29.971: vtsp_r2_end_dial: vdev_common=0x6205E5F8,

string=567ds_end_dial():

fsm_pop() act_caps_ind

Jan 7 10:00:29.971: act_caps_ind:Encap 1, Vad 2, Codec 0x4,

CodecBytes 20, FaxRate 2,

FaxBytes 20 SignalType 0 DtmfRelay 1, Modem 1act_caps_ack

Jan 7 10:00:29.971: dsp_idle_mode: [0:1 (17)] packet_Len=8

channel_id=4929 packet_id=68

Jan 7 10:00:29.971: act_caps_ack: codec = 15, ret = 1

Jan 7 10:00:29.971: dsp_cp_tone_off: [0:1 (17)] packet_Len=8

channel_id=4929 packet_id=71

Jan 7 10:00:29.971: dsp_idle_mode: [0:1 (17)] packet_Len=8

channel_id=4929 packet_id=68

Jan 7 10:00:29.971: dsp_encap_config_20: [0:1 (17)] packet_Len=24

channel_id=4929

packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0

r_vpxcc=0x0

Jan 7 10:00:29.971: dsp_voice_mode: [0:1 (17)] packet_Len=24

channel_id=4929 packet_id=73

coding_type=19 voice_field_size=20 VAD_flag=1 echo_length=64

comfort_noise=1

inband_detect=1 digit_relay=2 AGC_flag=0act_alert_connect

Jan 7 10:00:30.255: vtsp_ring_noan_timer_stop: 7063148

Jan 7 10:00:30.255: dsp_cp_tone_off: [0:1 (17)] packet_Len=8

channel_id=4929 packet_id=71

Jan 7 10:00:30.255: csm_vtsp_call_connect (vtsp_cdb=0x61B5BFF8,

voice_vdev=0x61F19688)

Jan 7 10:00:30.255: CSM_IC5_WAIT_FOR_SWITCH_OVER:

CSM_EVENT_MODEM_OFFHOOK at slot 1,

port 60

Jan 7 10:00:30.607: CSM_RX_CAS_EVENT_FROM_NEAT:(0007):

EVENT_CHANNEL_CONNECTED at slot 1

and port 60

Jan 7 10:00:30.607: CSM_PROC_IC6_WAIT_FOR_CONNECT:

CSM_EVENT_DSX0_CONNECTED at slot 1,

port 60

Jan 7 10:00:30.607: from NEAT(0): (0/8): TX ANSWERED (ABCD=0101)

eefje#

Informazioni correlate

- Segnalazione E1 R2 per Voice over IP sul server di accesso Cisco AS5300

- Segnalazione E1 R2 per i router Cisco serie 3620 e 3640

- Personalizzazione di E1 R2 con il comando cas-custom

- Configurazione E1 R2 e segnalazione associata a canale

- Segnalazione E1 R2 per i server di accesso Cisco AS5300 e Cisco AS5200

- Supporto alla tecnologia vocale

- Supporto ai prodotti voce e Unified Communications

- Risoluzione dei problemi di Cisco IP Telephony

- Documentazione e supporto tecnico – Cisco Systems