Questo documento descrive come configurare e verificare la VXLAN con il control plane BGP VPN sugli switch Cisco Nexus serie 9000 in un fabric spine-leaf.
Cisco raccomanda la conoscenza dei seguenti argomenti:
Le informazioni fornite in questo documento si basano sulle seguenti versioni software e hardware:
Le informazioni discusse in questo documento fanno riferimento a dispositivi usati in uno specifico ambiente di emulazione. Su tutti i dispositivi menzionati nel documento la configurazione è stata ripristinata ai valori predefiniti. Se la rete è operativa, valutare attentamente eventuali conseguenze derivanti dall'uso dei comandi.
Nota: La configurazione illustrata in questo documento è valida per le piattaforme Nexus 9000 Cloud Scale (-EX, -FX, -FX2, -FX3, -GX, -GX2 e versioni successive) in modalità NX-OS standalone. non è applicabile agli switch Nexus 9000 in modalità ACI.
| Termine |
Descrizione |
| VXLAN |
LAN estendibile virtuale: che fornisce servizi di sovrimpressione di layer 2 e layer 3 su un IP underlay indirizzato con incapsulamento MAC-in-UDP (porta UDP 4789). |
| VNI |
Identificatore di rete VXLAN: ID segmento a 24 bit. Una VNI L2 è mappata a una VLAN (dominio bridge). Un VNI L3 è associato a un VRF. |
| VTEP |
Endpoint tunnel VXLAN: Il dispositivo che incapsula e decapsula il traffico VXLAN. |
| NVE |
Network Virtualization Edge Interface (interfaccia nve1): L'interfaccia logica da cui vengono incapsulati e decapsulati. |
| BGP VPN |
Il control plane che annuncia MAC, MAC/IP (Route Type 2), prefisso IP (Route Type 5) e appartenenza VTEP (Route Type 3) tra VTEP. |
| AnyCast Gateway |
Lo stesso indirizzo IP e MAC SVI su ciascuna foglia e il gateway predefinito è sempre la foglia locale. |
| INSETTO |
Traffico broadcast, unicast sconosciuto e multicast. |
La versione precedente di questo documento usava flood-and-learn, in cui i VTEP imparavano gli indirizzi MAC remoti dall'flooding del piano dati. L'EVPN BGP sostituisce l'apprendimento del piano dati con un control plane ed è il modello di implementazione consigliato:
| Modalità |
Configurazione |
Requisito per la rappresentazione |
| Multicast (in questo documento) |
mcast-group <group> nel VNI |
PIM Sparse Mode su tutti i collegamenti e i loopback di underlay e un RP (anycast RP sulle spine è comune) |
| Replica in ingresso |
protocollo bgp in entrata-replica sotto il VNI |
Solo unicast. Il VTEP in entrata invia una copia a ogni VTEP remoto che il BGP Route Type 3 ha appreso per il VNI. |

| Sul dispositivo bootflash o slot0: |
Loopback0 (routing, BGP, PIM) |
Loopback1 (origine NVE) |
Uplink (da Eth1/49 a Spine-1, da Eth1/50 a Spine-2) |
| Dorso-1 |
10.0.0.1 |
- |
Da Eth1/1-3 a Leaf-1/2/3: 10.1.1.0, 0,2, 0,4/31 |
| Dorso-2 |
10.0.0.2 |
- |
Da Eth1/1-3 a Leaf-1/2/3: 10.1.2.0, 0,2, 0,4/31 |
| Foglia-1 |
10.0.0.11 |
10.0.1.11, secondario 10.0.1.112 |
10.1.1.1/31, 10.1.2.1/31 |
| Foglia 2 |
10.0.0.12 |
10.0.1.12, secondario 10.0.1.12 |
10.1.1.3/31, 10.1.2.3/31 |
| Foglia-3 |
10.0.0.13 |
10.0.1.13 |
10.1.1.5/31, 10.1.2.5/31 |
| Oggetto Overlay |
Valore |
| Anycast RP |
10.254.254.1 (loopback254 su entrambi gli aculei), gruppi 239.1.1.0/24 |
| VLAN 10 / VNI L2 |
10010, mcast-group 239.1.1.10, gateway 192.168.10.1/24 |
| VLAN 20 / VNI L2 |
10020, mcast-group 239.1.1.20, gateway 192.168.20.1/24 |
| VRF Tenant-A / L3 VNI |
5000 (VLAN 500) |
| MAC gateway Anycast |
2020.0000.00aa |
| SVI sottostante di backup vPC |
VLAN 3900, 10.255.255.0/31 (foglia-1) e 10.255.255.1/31 (foglia-2) |
Nota: Usare loopback separati per l'origine NVE (Loopback1), il routing e il peering BGP (Loopback0). Sui VTEP vPC, il loopback dell'origine NVE ha un IP secondario che è lo stesso su entrambi i peer. I VTEP remoti utilizzano questo indirizzo condiviso (vPC anycast VTEP) per raggiungere la coppia vPC come un unico VTEP.
Queste configurazioni mostrano solo le parti relative alla base e alla VXLAN. Configurare le funzionalità di gestione, AAA e altre in base ai requisiti.
nv overlay evpn
feature ospf
feature bgp
feature pim
feature nv overlay
ip pim rp-address 10.254.254.1 group-list 239.1.1.0/24
ip pim anycast-rp 10.254.254.1 10.0.0.1
ip pim anycast-rp 10.254.254.1 10.0.0.2
interface loopback0
description Routing / BGP / Anycast-RP member
ip address 10.0.0.1/32
ip router ospf UNDERLAY area 0.0.0.0
ip pim sparse-mode
interface loopback254
description Anycast-RP
ip address 10.254.254.1/32
ip router ospf UNDERLAY area 0.0.0.0
ip pim sparse-mode
interface Ethernet1/1
description to Leaf-1 Eth1/49
no switchport
mtu 9216
medium p2p
ip address 10.1.1.0/31
ip ospf network point-to-point
ip router ospf UNDERLAY area 0.0.0.0
ip pim sparse-mode
no shutdown
interface Ethernet1/2
description to Leaf-2 Eth1/49
no switchport
mtu 9216
medium p2p
ip address 10.1.1.2/31
ip ospf network point-to-point
ip router ospf UNDERLAY area 0.0.0.0
ip pim sparse-mode
no shutdown
interface Ethernet1/3
description to Leaf-3 Eth1/49
no switchport
mtu 9216
medium p2p
ip address 10.1.1.4/31
ip ospf network point-to-point
ip router ospf UNDERLAY area 0.0.0.0
ip pim sparse-mode
no shutdown
router ospf UNDERLAY
router-id 10.0.0.1
router bgp 65000
router-id 10.0.0.1
address-family l2vpn evpn
template peer VTEP
remote-as 65000
update-source loopback0
address-family l2vpn evpn
send-community
send-community extended
route-reflector-client
neighbor 10.0.0.11
inherit peer VTEP
neighbor 10.0.0.12
inherit peer VTEP
neighbor 10.0.0.13
inherit peer VTEP
interface loopback0
ip address 10.0.0.2/32
interface Ethernet1/1
ip address 10.1.2.0/31
interface Ethernet1/2
ip address 10.1.2.2/31
interface Ethernet1/3
ip address 10.1.2.4/31
router ospf UNDERLAY
router-id 10.0.0.2
router bgp 65000
router-id 10.0.0.2
nv overlay evpn
feature ospf
feature bgp
feature pim
feature fabric forwarding
feature interface-vlan
feature vn-segment-vlan-based
feature lacp
feature vpc
feature nv overlay
fabric forwarding anycast-gateway-mac 2020.0000.00aa
ip pim rp-address 10.254.254.1 group-list 239.1.1.0/24
vlan 10
vn-segment 10010
vlan 20
vn-segment 10020
vlan 500
name L3VNI-Tenant-A
vn-segment 50000
vlan 3900
name vPC-backup-underlay
system nve infra-vlans 3900
vrf context Tenant-A
vni 50000
rd auto
address-family ipv4 unicast
route-target both auto
route-target both auto evpn
vpc domain 10
peer-switch
role priority 10
peer-keepalive destination 172.16.0.2 source 172.16.0.1 vrf management
delay restore 150
peer-gateway
ip arp synchronize
ipv6 nd synchronize
interface port-channel1
description vPC peer-link
switchport
switchport mode trunk
switchport trunk allowed vlan 10,20,500,3900
spanning-tree port type network
vpc peer-link
interface port-channel11
description Server-1
switchport
switchport mode trunk
switchport trunk allowed vlan 10,20
spanning-tree port type edge trunk
mtu 9216
vpc 11
interface Vlan10
no shutdown
vrf member Tenant-A
no ip redirects
ip address 192.168.10.1/24
fabric forwarding mode anycast-gateway
interface Vlan20
no shutdown
vrf member Tenant-A
no ip redirects
ip address 192.168.20.1/24
fabric forwarding mode anycast-gateway
interface Vlan500
description L3VNI Tenant-A
no shutdown
vrf member Tenant-A
no ip redirects
ip forward
interface Vlan3900
description vPC backup underlay
no shutdown
mtu 9216
no ip redirects
ip address 10.255.255.0/31
ip ospf network point-to-point
ip router ospf UNDERLAY area 0.0.0.0
ip pim sparse-mode
interface nve1
no shutdown
host-reachability protocol bgp
advertise virtual-rmac
source-interface loopback1
member vni 10010
suppress-arp
mcast-group 239.1.1.10
member vni 10020
suppress-arp
mcast-group 239.1.1.20
member vni 50000 associate-vrf
interface Ethernet1/1
description Server-1
switchport
switchport mode trunk
switchport trunk allowed vlan 10,20
mtu 9216
channel-group 11 mode active
no shutdown
interface Ethernet1/53-54
description vPC peer-link to Leaf-2
switchport
switchport mode trunk
switchport trunk allowed vlan 10,20,500,3900
channel-group 1 mode active
no shutdown
interface Ethernet1/49
description to Spine-1 Eth1/1
no switchport
mtu 9216
medium p2p
ip address 10.1.1.1/31
ip ospf network point-to-point
ip router ospf UNDERLAY area 0.0.0.0
ip pim sparse-mode
no shutdown
interface Ethernet1/50
description to Spine-2 Eth1/1
no switchport
mtu 9216
medium p2p
ip address 10.1.2.1/31
ip ospf network point-to-point
ip router ospf UNDERLAY area 0.0.0.0
ip pim sparse-mode
no shutdown
interface loopback0
description Routing / BGP
ip address 10.0.0.11/32
ip router ospf UNDERLAY area 0.0.0.0
ip pim sparse-mode
interface loopback1
description NVE source
ip address 10.0.1.11/32
ip address 10.0.1.112/32 secondary
ip router ospf UNDERLAY area 0.0.0.0
ip pim sparse-mode
router ospf UNDERLAY
router-id 10.0.0.11
router bgp 65000
router-id 10.0.0.11
address-family l2vpn evpn
advertise-pip
template peer SPINE-RR
remote-as 65000
update-source loopback0
address-family l2vpn evpn
send-community
send-community extended
neighbor 10.0.0.1
inherit peer SPINE-RR
neighbor 10.0.0.2
inherit peer SPINE-RR
vrf Tenant-A
address-family ipv4 unicast
advertise l2vpn evpn
evpn
vni 10010 l2
rd auto
route-target import auto
route-target export auto
vni 10020 l2
rd auto
route-target import auto
route-target export auto
Nota: Sui VTEP vPC su scala cloud, la SVI (VLAN 3900) di backup sottostante deve essere elencata nelle infra-vlan di system nve. Questa VLAN deve essere nella VRF predefinita, non deve avere un segmento VN e deve essere consentita sul collegamento peer. Trasporta il traffico VXLAN sul collegamento peer per le porte orfane e quando un peer vPC perde tutti i suoi uplink. Non configurare le VLAN infra con ID separati da 512, ad esempio 10 e 522.
annuncio-pip e annuncio di virtual-rmac dai peer vPC, che annunciano le route di tipo-5 (prefisso) e le route host-orfano con il relativo IP primario (PIP) e il proprio MAC router. Senza questi, il traffico verso un host dietro un solo peer può essere inviato al peer che non può raggiungerlo.
La soppressione ARP (suppress-arp) è supportata solo per i VNI in cui il VTEP è il gateway anycast distribuito per quel VNI.
vpc domain 10
role priority 20
peer-keepalive destination 172.16.0.1 source 172.16.0.2 vrf management
interface Vlan3900
ip address 10.255.255.1/31
interface Ethernet1/49
ip address 10.1.1.3/31
interface Ethernet1/50
ip address 10.1.2.3/31
interface loopback0
ip address 10.0.0.12/32
interface loopback1
ip address 10.0.1.12/32
ip address 10.0.1.112/32 secondary
router ospf UNDERLAY
router-id 10.0.0.12
router bgp 65000
router-id 10.0.0.12
Attenzione: La configurazione NVE (VNI, gruppi mcast, interfaccia di origine, IP secondario) deve essere identica su entrambi i peer vPC. Una mancata corrispondenza è un errore di coerenza di tipo 1 del vPC e l'interfaccia NVE o i VNI sono sospesi. Eseguire il comando show vpc consistency-parameters global.
nv overlay evpn
feature ospf
feature bgp
feature pim
feature fabric forwarding
feature interface-vlan
feature vn-segment-vlan-based
feature nv overlay
fabric forwarding anycast-gateway-mac 2020.0000.00aa
ip pim rp-address 10.254.254.1 group-list 239.1.1.0/24
vlan 10
vn-segment 10010
vlan 20
vn-segment 10020
vlan 500
name L3VNI-Tenant-A
vn-segment 50000
vrf context Tenant-A
vni 50000
rd auto
address-family ipv4 unicast
route-target both auto
route-target both auto evpn
interface Vlan10
no shutdown
vrf member Tenant-A
no ip redirects
ip address 192.168.10.1/24
fabric forwarding mode anycast-gateway
interface Vlan20
no shutdown
vrf member Tenant-A
no ip redirects
ip address 192.168.20.1/24
fabric forwarding mode anycast-gateway
interface Vlan500
no shutdown
vrf member Tenant-A
no ip redirects
ip forward
interface nve1
no shutdown
host-reachability protocol bgp
source-interface loopback1
member vni 10010
suppress-arp
mcast-group 239.1.1.10
member vni 10020
suppress-arp
mcast-group 239.1.1.20
member vni 50000 associate-vrf
interface Ethernet1/1
description Server-2
switchport
switchport access vlan 10
spanning-tree port type edge
no shutdown
interface Ethernet1/2
description Server-3
switchport
switchport access vlan 20
spanning-tree port type edge
no shutdown
interface Ethernet1/49
description to Spine-1 Eth1/3
no switchport
mtu 9216
medium p2p
ip address 10.1.1.5/31
ip ospf network point-to-point
ip router ospf UNDERLAY area 0.0.0.0
ip pim sparse-mode
no shutdown
interface Ethernet1/50
description to Spine-2 Eth1/3
no switchport
mtu 9216
medium p2p
ip address 10.1.2.5/31
ip ospf network point-to-point
ip router ospf UNDERLAY area 0.0.0.0
ip pim sparse-mode
no shutdown
interface loopback0
ip address 10.0.0.13/32
ip router ospf UNDERLAY area 0.0.0.0
ip pim sparse-mode
interface loopback1
description NVE source
ip address 10.0.1.13/32
ip router ospf UNDERLAY area 0.0.0.0
ip pim sparse-mode
router ospf UNDERLAY
router-id 10.0.0.13
router bgp 65000
router-id 10.0.0.13
template peer SPINE-RR
remote-as 65000
update-source loopback0
address-family l2vpn evpn
send-community
send-community extended
neighbor 10.0.0.1
inherit peer SPINE-RR
neighbor 10.0.0.2
inherit peer SPINE-RR
vrf Tenant-A
address-family ipv4 unicast
advertise l2vpn evpn
evpn
vni 10010 l2
rd auto
route-target import auto
route-target export auto
vni 10020 l2
rd auto
route-target import auto
route-target export auto
Se l'underlay non esegue il multicast, sostituire mcast-group con la replica in entrata basata su BGP su ogni VTEP. PIM e la configurazione RP non sono richiesti per i VNI L2.
interface nve1
member vni 10010
suppress-arp
ingress-replication protocol bgp
member vni 10020
suppress-arp
ingress-replication protocol bgp
Per verificare che la configurazione funzioni correttamente, consultare questa sezione.
Cisco CLI Analyzer (solo utenti registrati) supporta alcuni comandi show. Usare Cisco CLI Analyzer per visualizzare un'analisi degli output del comando show.
| Area |
Comandi |
| Sottolineatura |
show ip ospf neighbors, show ip route 10.0.1.13, show ip pim neighbors, show ip pim rp |
| Piano di controllo sovrapposizione |
show bgp l2vpn evpn summary, show bgp l2vpn evpn |
| NVE |
show nve interface nve1 detail, show nve peer, show nve vni |
| Apprendimento MAC/IP |
show mac address-table vlan 10, show l2route evpn mac all, show l2route evpn mac-ip all, show ip arp suppression-cache detail |
| VNI L3 |
show ip route vrf Tenant-A, show bgp l2vpn evpn route-type 2, show bgp l2vpn evpn route-type 5 |
| Replica Multicast |
show ip route 239.1.1.10 |
| vPC |
show vpc, show vpc consistency-parameters global, show system nve infra-vlan |
Questi output provengono da uno stato stabile dopo l'invio del traffico tra Server-1, Server-2 e Server-3.
Leaf-1# show ip pim rp
PIM RP Status Information for VRF "default"
BSR disabled
Auto-RP disabled
BSR RP Candidate policy: None
BSR RP policy: None
Auto-RP Announce policy: None
Auto-RP Discovery policy: None
Anycast-RP 10.254.254.1 members:
10.0.0.1 10.0.0.2
RP: 10.254.254.1, (0),
uptime: 1d01h priority: 255,
RP-source: (local),
group ranges:
239.1.1.0/24
Leaf-1# show bgp l2vpn evpn summary
BGP summary information for VRF default, address family L2VPN EVPN
BGP router identifier 10.0.0.11, local AS number 65000
BGP table version is 58, L2VPN EVPN config peers 2, capable peers 2
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
10.0.0.1 4 65000 1520 1488 58 0 0 1d01h 9
10.0.0.2 4 65000 1519 1490 58 0 0 1d01h 9
Leaf-1# show nve interface nve1 detail
Interface: nve1, State: Up, encapsulation: VXLAN
VPC Capability: VPC-VIP-Only [notified]
Local Router MAC: 5254.0011.1b08
Host Learning Mode: Control-Plane
Source-Interface: loopback1 (primary: 10.0.1.11, secondary: 10.0.1.112)
Source Interface State: Up
Virtual RMAC Advertisement: Yes
NVE Flags:
Interface Handle: 0x49000001
Source Interface hold-down-time: 180
Source Interface hold-up-time: 30
Remaining hold-down time: 0 seconds
Virtual Router MAC: 0200.0a00.0170
Leaf-1# show nve peers
Interface Peer-IP State LearnType Uptime Router-Mac
--------- -------------------------------------- ----- --------- -------- -----------------
nve1 10.0.1.13 Up CP 1d01h 5254.0013.1b08
Leaf-1# show nve vni
Codes: CP - Control Plane DP - Data Plane
UC - Unconfigured SA - Suppress ARP
S-ND - Suppress ND
SU - Suppress Unknown Unicast
Xconn - Crossconnect
MS-IR - Multisite Ingress Replication
HYB - Hybrid IRB mode
Interface VNI Multicast-group State Mode Type [BD/VRF] Flags
--------- -------- ----------------- ----- ---- ------------------ -----
nve1 10010 239.1.1.10 Up CP L2 [10] SA
nve1 10020 239.1.1.20 Up CP L2 [20] SA
nve1 50000 n/a Up CP L3 [Tenant-A]
Nota: Con l'EVPN BGP, i peer NVE vengono visualizzati quando un VTEP remoto annuncia le route per un VNI configurato localmente (LearnType CP). Leaf-3 vede la coppia vPC come un peer, il VTEP AnyCast 10.0.1.12. Con ADVERTIise-pip, Leaf-3 vede anche gli IP primari vPC 10.0.1.11 e 10.0.1.12 per il tipo-5 e le route orfane.
Leaf-1# show l2route evpn mac all
Flags -(Rmac):Router MAC (Stt):Static (L):Local (R):Remote (V):vPC link
(Dup):Duplicate (Spl):Split (Rcv):Recv (AD):Auto-Delete (D):Del Pending
(S):Stale (C):Clear, (Ps):Peer Sync (O):Re-Originated (Nho):NH-Override
(Pf):Permanently-Frozen, (Orp): Orphan
Topology Mac Address Prod Flags Seq No Next-Hops
----------- -------------- ------ ------------- ---------- ----------------
10 0050.5601.0a0a Local L, 0 Po11
10 0050.5603.0a14 BGP SplRcv 0 10.0.1.13 (Label: 10010)
20 0050.5603.1e1e BGP SplRcv 0 10.0.1.13 (Label: 10020)
Leaf-1# show ip arp suppression-cache detail
Flags: + - Adjacencies synced via CFSoE
L - Local Adjacency
R - Remote Adjacency
L2 - Learnt over L2 interface
PS - Added via L2RIB, Peer Sync
RO - Dervied from L2RIB Peer Sync Entry
Ip Address Age Mac Address Vlan Physical-ifindex Flags Remote Vtep Addrs
192.168.10.10 00:02:11 0050.5601.0a0a 10 port-channel11 L
192.168.10.20 00:05:42 0050.5603.0a14 10 (null) R 10.0.1.13
Leaf-1# show ip route vrf Tenant-A 192.168.20.30
IP Route Table for VRF "Tenant-A"
'*' denotes best ucast next-hop
'**' denotes best mcast next-hop
'[x/y]' denotes [preference/metric]
'%<string>' in via output denotes VRF <string>
192.168.20.30/32, ubest/mbest: 1/0
*via 10.0.1.13%default, [200/0], 00:10:21, bgp-65000, internal, tag 65000, segid: 50000 tunnelid: 0xa00010d encap: VXLAN
Leaf-1# show vpc consistency-parameters global | include Nve|Src|Sec|Host
Nve1 Adm St, Src Adm St, 1 Up, Up, 10.0.1.112, CP, Up, Up, 10.0.1.112, CP,
Sec IP, Host Reach, VMAC TRUE, Disabled, TRUE, Disabled,
Adv, SA,mcast l2, mcast 0.0.0.0, 0.0.0.0, Disabled, 0.0.0.0, 0.0.0.0, Disabled,
Nve Vni Configuration 1 10010-10020 10010-10020
Leaf-1# show system nve infra-vlans
Currently active infra-vlans: 3900
Tutti i pacchetti VXLAN provengono dal loopback dell'origine NVE del VTEP in entrata. Per gli host sulle porte vPC, si tratta dell'IP secondario condiviso (10.0.1.12). Il traffico unicast noto va all'IP NVE del VTEP remoto. Il traffico BUM va al gruppo multicast della VNI, o con la replica in entrata, e una copia unicast va a ciascun VTEP remoto.
| Intestazione |
Esempio: Da server-1 a server-2 (VLAN 10, VNI L2) |
Esempio: Da server-1 a server-3 (routing, VNI L3) |
| Ethernet esterna |
MAC uplink foglia-1 su MAC dorso |
MAC uplink foglia-1 su MAC dorso |
| IP esterno |
da 10.0.1.12 a 10.0.1.13 |
da 10.0.1.12 a 10.0.1.13 (da 10.0.1.11 a 10.0.1.13 se il traffico proviene da una porta orfana e si utilizza advertising-pip) |
| UDP esterno |
La porta di origine è un hash del flusso interno (entropia per ECMP); porta di destinazione 4789 |
Uguale |
| VXLAN |
Flag 0x08 (flag I), VNI 10010 |
Flag 0x08, VNI 50000 |
| Ethernet interna |
MAC da Server-1 a MAC Server-2 |
MAC router foglia-1 su MAC router foglia-3 |
| IP interno |
da 192.168.10.10 a 192.168.10.20 |
da 192.168.10.10 a 192.168.20.30 (TTL diminuito) |
Nota: VXLAN aggiunge 50 byte al frame originale. Impostare l'MTU sottostante (tutti gli uplink spine e foglia e la SVI di backup vPC) su almeno 50 byte in più rispetto alla MTU dell'host più grande. Si consiglia 9216.
| Sintomo |
Assegno |
Causa comune |
| Peer NVE non in visualizzazione peer NVE |
show bgp l2vpn evpn summary, show ip route <IP NVE remoto>, show nve vni |
Sessione VPN BGP inattiva; loopback NVE remoto non pubblicizzato nella base; VNI non configurato su entrambi i VTEP; elemento send-community esteso mancante |
| Interfaccia NVE inattiva o VNI sospesi su un VTEP vPC |
show nve interface nve1 detail, show vpc consistency-parameters global |
Mancata corrispondenza della configurazione NVE tra peer; il loopback della sorgente è ancora nel timer di attesa dopo un ricaricamento; IP secondario mancante o diverso |
| Gli host nella stessa VNI non possono comunicare oppure ARP non riesce |
show l2route evpn mac all, show ip arp suppression-cache detail, show ip mroute <gruppo> |
RT-2 non ricevuto (route-target o mancata corrispondenza VNI); BUM non replicato (nessun router adiacente PIM, senza RP, PIM mancante nel loopback NVE); suppress-arp su un VNI senza SVI anycast gateway |
| Routing tra VNI non riuscito |
show ip route vrf Tenant-A, show nve vni (stato VNI L3), show bgp l2vpn evpn route-type 5 |
VLAN L3 o SVI mancante o chiusa; vni mancante nel contesto VRF; pubblicizzare l2vpn evpn mancante nel BGP VRF; route-target entrambi auto evpn mancante |
| Il traffico ha esito negativo solo per le porte orfane o dopo che un peer vPC ha perso i propri uplink |
show system nve infra-vlan, show ip ospf neighbors vrf predefinito |
SVI sottostante di backup mancante, non presente nelle infra-vlan di sistema o non consentita sul collegamento peer |
| Pacchetti grandi scartati, pacchetti piccoli funzionanti |
show interface <uplink> (errori TX), ping con bit DF impostato tra i loopback NVE |
MTU underlay troppo piccola per il sovraccarico della VXLAN |
Nota: Questi elementi non sono supportati come uplink VXLAN:
Il loopback dell'origine NVE deve trovarsi nel VRF predefinito.
| Revisione | Data di pubblicazione | Commenti |
|---|---|---|
3.0 |
28-Oct-2026
|
Introduzione aggiornata, ortografia, grammatica, spaziatura, righe orizzontali inserite per separare le sezioni per la leggibilità, avvisi CCW fissi, URL, testo alternativo. |
2.0 |
15-Nov-2022
|
Errori di introduzione aggiornati, disclaimer legale, gerund, traduzione automatica, SEO, requisiti di stile e formattazione. |
1.0 |
10-Jul-2015
|
Versione iniziale |