Comment ajouter l'authentification AAA (Xauth) au logiciel IPSec PIX version 5.2 et ultérieure

Introduction

L'authentification et la comptabilité RADIUS et TACACS+, et dans une certaine mesure, l'autorisation, sont effectuées pour les tunnels de client matériel Cisco Secure VPN Client 1.1 et Cisco VPN 3000 2.5 qui se terminent au PIX. Les changements dans PIX 5.2 et l'authentification étendue ultérieure (Xauth) par rapport à ceux des versions précédentes qui incluent la prise en charge de la liste d'accès d'authentification, d'autorisation et de comptabilité (AAA) pour contrôler ce que les utilisateurs authentifiés peuvent accéder et prendre en charge pour la terminaison Xauth du client Cisco VPN 3000 2.5. La commande vpn group split-tunneling permet au client VPN 3000 de se connecter au réseau à l'intérieur du PIX ainsi qu'à d'autres réseaux (par exemple, Internet) en même temps. Dans PIX 5.3 et les versions ultérieures, le changement AAA par rapport aux versions précédentes du code est que les ports RADIUS sont configurables. Dans PIX 6.0, la prise en charge du client VPN 3.x est ajoutée. Cela nécessite Diffie-Hellman groupe 2.

Conditions préalables

Exigences

Aucune exigence spécifique n'est associée à ce document.

Composants utilisés

Les informations contenues dans ce document sont basées sur les versions de matériel et de logiciel suivantes :

• Logiciel PIX version 5.2.1

• Client VPN sécurisé Cisco 1.1

• Client Cisco VPN 3000 2.5 ou Client VPN 3.x

  Remarque : la version 3.0.x du client VPN Cisco ne fonctionne pas avec les versions PIX antérieures à la version 6.0. Référez-vous à Matériel Cisco et clients VPN prenant en charge IPsec/PPTP/L2TP pour plus d'informations.

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Conventions

Pour plus d'informations sur les conventions utilisées dans ce document, reportez-vous à Conventions relatives aux conseils techniques Cisco.

Informations générales

La version 6.2 du logiciel PIX Firewall prend en charge le téléchargement de listes de contrôle d'accès (ACL) vers le PIX Firewall à partir d'un serveur de contrôle d'accès (ACS). Cela permet de configurer des listes de contrôle d'accès par utilisateur sur un serveur AAA pour fournir une autorisation de liste de contrôle d'accès par utilisateur. Il est ensuite téléchargeable via l'ACS vers le pare-feu PIX. Cette fonctionnalité est prise en charge pour les serveurs RADIUS uniquement. Il n'est pas pris en charge pour les serveurs TACACS+.

Étapes de débogage

Effectuez ces étapes de débogage :

1. Assurez-vous que la configuration de PIX Xauth fonctionne avant d'ajouter l'authentification AAA.

   Si vous ne pouvez pas transmettre le trafic avant d'implémenter AAA, vous ne pourrez pas le faire par la suite.

2. Activez un type de journalisation dans le PIX :

   • N'émettez pas la commande logging console debugging sur un système lourdement chargé.

   • La commande logging buffered debugging peut être émise. Exécutez ensuite la commande show logging.

   • La journalisation peut également être envoyée à un serveur Syslog (System Message Log) et examinée.

3. Activez le débogage sur les serveurs TACACS+ ou RADIUS. Tous les serveurs disposent de cette option.

Commandes de débogage sur PIX

• debug crypto ipsec sa — Cette commande debug affiche les événements IPsec.

• debug crypto isakmp sa — Cette commande debug affiche des messages sur les événements IKE (Internet Key Exchange).

• debug crypto isakmp engine — Cette commande debug affiche des messages sur les événements IKE.

Débogage côté client

Activez Log Viewer pour afficher les débogages côté client dans Cisco Secure 1.1 ou VPN 3000 Client 2.5.

Profils de serveur AAA

Cisco Secure UNIX TACACS+

user = noacl{
password = clear "********" 
service=shell {
} 
}
user = pixb{
  password = clear "********" 
  service=shell {
  set acl=115
  } 
  }
user = 3000full{
  password = clear "********" 
  service=shell {
  } 
  } 
user = 3000partial{
  password = clear "********" 
  service=shell {
  } 
  }

Cisco Secure ACS pour Windows TACACS+

Les utilisateurs noacl, 3000full et 3000partial n'ont besoin que d'un nom d'utilisateur et d'un mot de passe dans Cisco Secure ACS pour Windows. L'utilisateur pixb a besoin d'un nom d'utilisateur, d'un mot de passe, d'un groupe shell/exec archivé, d'une liste de contrôle d'accès archivée et de 115 caractères dans la zone.

Cisco Secure UNIX RADIUS

user = noacl{
password = clear "********" 
}
user = pixb{
  password = clear "********" 
  radius=Cisco {
  reply_attributes= {
  9,1="acl=115"
  } 
  } 
  }
user = 3000full{
  password = clear "********" 
  }
user = 3000partial{
  password = clear "********" 
  }

Cisco Secure ACS pour Windows RADIUS

RADIUS/Cisco est le type de périphérique. Les utilisateurs noacl, 3000full et 3000partial n'ont besoin que d'un nom d'utilisateur et d'un mot de passe dans Cisco Secure ACS pour Windows. L'utilisateur pixb a besoin d'un nom d'utilisateur, d'un mot de passe et d'une coche et acl=115 dans la zone rectangulaire Cisco/RADIUS où il indique 009\001 AV-Pair (spécifique au fournisseur).

Remarque : vous avez besoin de l'attribut vendor pour la liste de contrôle d'accès. L'attribut 11, id-filtre, n'est pas valide. L'ID de bogue Cisco CSCdt50422 (clients enregistrés uniquement) est attribué à ce problème. Il est corrigé dans le logiciel PIX version 6.0.1.

RADIUS Merit (prise en charge des paires Cisco AV)

noacl Password= "noacl" 

pixb Password= "pixb"
cisco-avpair = "acl=115"

3000full Password= "3000full"

3000partial Password= "3000partial"

Diagramme du réseau

Ports RADIUS configurables (versions 5.3 et ultérieures)

Certains serveurs RADIUS utilisent des ports RADIUS autres que 1645/1646 (généralement 1812/1813). Dans PIX 5.3 et les versions ultérieures, les ports d'authentification et de comptabilité RADIUS peuvent être changés en ports autres que les ports 1645/1646 par défaut avec ces commandes :

• aaa-server radius-authport #

• aaa-server radius-acctport #

Comment s'authentifier avec Xauth sans groupes VPN

Dans cet exemple, les trois clients VPN sont authentifiés avec Xauth. Cependant, les clients VPN peuvent accéder uniquement au réseau à l'intérieur du PIX, car le split-tunneling n'est pas utilisé. Consultez Comment authentifier Xauth avec des groupes VPN pour plus d'informations sur le split-tunneling. Les listes de contrôle d'accès transmises depuis le serveur AAA s'appliquent à tous les clients VPN. Dans cet exemple, l'objectif est que l'utilisateur noacl se connecte et accède à toutes les ressources à l'intérieur du PIX. L'utilisateur pixb se connecte, mais comme l'ACL 115 est transmise depuis le serveur AAA pendant le processus Xauth, l'utilisateur ne peut accéder qu'à 10.1.1.40. L'accès à 10.1.1.41 et à toutes les autres adresses IP internes est refusé.

Remarque : la version 6.0 du logiciel PIX est requise pour la prise en charge du client VPN 3.0.

Configuration de Cisco Secure VPN Client 1.1 - Xauth sans groupes VPN

Name of connection:
Remote party address = IP_Subnet = 10.1.1.0, Mask 255.255.255.0
Connect using Secure Gateway Tunnel to 172.18.124.157
My Identity:
Select certificate = None
ID_Type = ip address, pre-shared key and fill in key
('cisco1234') - matches that of pix in 'isakmp key' command
Security policy = defaults
Proposal 1 (Authen) = DES, MD5
Proposal 2 (Key Exchange) = DES, MD5, Tunnel

Ouvrez une fenêtre de déni de service (DoS) et exécutez la commande ping -t #.#.#.#. Lorsque la fenêtre Xauth s'affiche, tapez le nom d'utilisateur et le mot de passe qui correspondent à ceux du serveur AAA.

Configuration du client VPN 3000 2.5 ou VPN Client 3.x - Xauth sans groupes VPN

Procédez comme suit :

1. Sélectionnez Options > Properties > Authentication > Group Name.

2. Le nom du groupe est don't_care et le mot de passe correspond à celui sur PIX dans la commande isakmp key. Le nom d'hôte est 172.18.124.157.

3. Cliquez sur Connect.

4. Lorsque la fenêtre Xauth s'affiche, tapez le nom d'utilisateur et le mot de passe qui correspondent à ceux du serveur AAA.

Xauth sans groupes VPN - Configuration PIX

PIX Version 5.2(1)
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
hostname goss-pixb
fixup protocol ftp 21
fixup protocol http 80
fixup protocol h323 1720
fixup protocol rsh 514
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol sip 5060
names
access-list 108 permit ip 10.1.1.0 255.255.255.0 
192.168.1.0 255.255.255.0 
access-list 115 deny ip any host 10.1.1.41 
access-list 115 permit ip any host 10.1.1.40
pager lines 24
logging on
no logging timestamp
no logging standby
logging console debugging
no logging monitor
no logging buffered
logging trap debugging
no logging history
logging facility 20
logging queue 512
interface ethernet0 auto
interface ethernet1 auto
mtu outside 1500
mtu inside 1500
ip address outside 172.18.124.157 255.255.255.0
ip address inside 10.1.1.101 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool test 192.168.1.1-192.168.1.5
no failover
failover timeout 0:00:00
failover poll 15
failover ip address outside 0.0.0.0
failover ip address inside 0.0.0.0
arp timeout 14400
global (outside) 1 172.18.124.154
nat (inside) 0 access-list 108
Nat (inside) 1 10.1.1.0 255.255.255.0 0 0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 
rpc 0:10:00 h323 0:05:00 
sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
AAA-server TACACS+ protocol tacacs+ 
AAA-server RADIUS protocol radius 
AAA-server AuthInbound protocol tacacs+ 
AAA-server AuthInbound (outside) host 172.18.124.114 cisco timeout 5
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
no sysopt route dnat
crypto ipsec transform-set myset esp-des esp-md5-hmac 
crypto dynamic-map dynmap 10 set transform-set myset
crypto map mymap 10 ipsec-isakmp dynamic dynmap
crypto map mymap client configuration address initiate
crypto map mymap client configuration address respond
crypto map mymap client authentication AuthInbound
crypto map mymap interface outside
isakmp enable outside
isakmp key ******** address 0.0.0.0 netmask 0.0.0.0 
isakmp identity address
isakmp client configuration address-pool local test outside

!--- Internet Security Association and Key Management Protocol (ISAKMP) !--- Policy for Cisco VPN Client 2.5 or !--- Cisco Secure VPN Client 1.1.

isakmp policy 10 authentication pre-share
isakmp policy 10 encryption des
isakmp policy 10 hash md5

!--- The 1.1 and 2.5 VPN Clients use Diffie-Hellman (D-H) !--- group 1 policy (PIX default).

isakmp policy 10 group 1
isakmp policy 10 lifetime 86400
! 

!--- ISAKMP Policy for VPN Client 3.0

isakmp policy 20 authentication pre-share
isakmp policy 20 encryption des
isakmp policy 20 hash md5

!--- The VPN 3.0 Clients use D-H group 2 policy !--- and PIX 6.0 code.

isakmp policy 20 group 2
isakmp policy 20 lifetime 86400
telnet timeout 5
ssh timeout 5
terminal width 80
Cryptochecksum:05c6a2f3a7d187162c4408503b55affa
: end
[OK]

Comment s'authentifier avec Xauth avec des groupes VPN

Dans cet exemple, le client VPN 3000 2.5 ou le client VPN 3.0 peut être authentifié avec Xauth, et la transmission tunnel partagée est en vigueur. En vertu de l'appartenance au groupe VPN, une ACL est passée du PIX au client VPN 3000. Il spécifie que seul le réseau à l'intérieur du PIX a un tunnel chiffré. Le reste du trafic (peut-être vers Internet) n'est pas chiffré.

Dans cet exemple, un client VPN, avec le nom d'utilisateur 3000full (sur le serveur AAA), dans le groupe vpn3000-all (sur le PIX) accède à l'ensemble du réseau 10.1.1.X à l'intérieur du PIX en même temps qu'à Internet. Le client VPN reçoit des informations sur le serveur wins, le serveur dns et le nom de domaine. L'autre client VPN, avec le nom d'utilisateur 3000partial (sur le serveur AAA), dans le groupe vpn3000-41 (sur le PIX) accède à une seule adresse IP à l'intérieur du réseau (10.1.1.40) en vertu du profil de groupe. Ce client VPN ne reçoit pas d'informations sur le serveur WINS et DNS, mais continue à utiliser la transmission tunnel partagée.

Remarque : la version 6.0 du logiciel PIX est requise pour la prise en charge du client VPN 3.0.

Configuration du client VPN 2.5 ou 3.0 - Xauth avec groupes VPN

Procédez comme suit :

Remarque : la configuration du client VPN 2.5 ou 3.0 dépend de l'utilisateur concerné.

1. Sélectionnez Options > Propriétés > Authentification.

2. Le nom de groupe et le mot de passe de groupe correspondent au nom de groupe sur le PIX comme dans : vpngroup vpn3000-all password ******** ou vpngroup vpn3000-41 password ********. Le nom d'hôte est 172.18.124.157.

3. Cliquez sur Connect.

4. Lorsque la fenêtre Xauth s'affiche, saisissez le nom d'utilisateur et le mot de passe qui correspondent à ceux du serveur AAA.

Dans cet exemple, une fois l'utilisateur 3000full authentifié, il récupère les informations du groupe vpn3000-all. L'utilisateur 3000partial récupère les informations du groupe vpn3000-41. La fenêtre affiche les profils de sécurité Négociation et Votre lien est maintenant sécurisé.

L'utilisateur 3000full utilise le mot de passe pour le groupe vpn3000-all. La liste d'accès 108 est associée à ce groupe à des fins de transmission tunnel partagée. Le tunnel est formé vers le réseau 10.1.1.x. Le trafic circule sans être chiffré vers les périphériques qui ne figurent pas dans la liste d’accès 108 (par exemple, Internet). C'est la transmission tunnel partagée.

Voici le résultat de la fenêtre d'état de connexion du client VPN pour l'utilisateur 3000full :

        Network         Mask 
key     10.1.1.0        255.255.255.0
key     172.18.124.157  255.255.255.255

L'utilisateur 3000partial utilise le mot de passe pour le groupe vpn3000-41. La liste d'accès 125 est associée à ce groupe à des fins de transmission tunnel partagée. Le tunnel est formé vers le périphérique 10.1.1.41. Le trafic circule sans être chiffré vers les périphériques qui ne figurent pas dans la liste d’accès 125 (par exemple, Internet). Cependant, le trafic ne circule pas vers le périphérique 10.1.1.40, car il n’est pas routable. Il n'est pas spécifié dans la liste des tunnels de cryptage.

Voici le résultat de la fenêtre d'état de connexion du client VPN pour l'utilisateur 3000partial :

        Network         Mask
key     10.1.1.41       255.255.255.255
key     172.18.124.157  255.255.255.255

Xauth avec groupes VPN - Configuration PIX

Remarque : le client VPN sécurisé Cisco 1.1 ne fonctionne pas avec cette fonction car il n'existe pas de clé ISAKMP (Internet Security Association and Key Management Protocol). Ajoutez la commande isakmp key ******** address 0.0.0.0 netmask 0.0.0.0 pour faire fonctionner tous les clients VPN.

PIX Version 5.2(1)
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd OnTrBUG1Tp0edmkr encrypted
hostname goss-pixb
fixup protocol ftp 21
fixup protocol http 80
fixup protocol h323 1720
fixup protocol rsh 514
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol sip 5060
names
access-list 108 permit ip 10.1.1.0 255.255.255.0 
192.168.1.0 255.255.255.0 
access-list 125 permit ip host 10.1.1.41 any 
pager lines 24
logging on
no logging timestamp
no logging standby
logging console debugging
no logging monitor
no logging buffered
logging trap debugging
no logging history
logging facility 20
logging queue 512
interface ethernet0 auto
interface ethernet1 auto
mtu outside 1500
mtu inside 1500
ip address outside 172.18.124.157 255.255.255.0
ip address inside 10.1.1.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool test 192.168.1.1-192.168.1.5
no failover
failover timeout 0:00:00
failover poll 15
failover ip address outside 0.0.0.0
failover ip address inside 0.0.0.0
arp timeout 14400
global (outside) 1 172.18.124.154
Nat (inside) 0 access-list 108
Nat (inside) 1 10.1.1.0 255.255.255.0 0 0
route outside 0.0.0.0 0.0.0.0 172.18.124.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 
rpc 0:10:00 h323 0:05:00 
sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
AAA-server TACACS+ protocol tacacs+ 
AAA-server RADIUS protocol radius 
AAA-server AuthInbound protocol tacacs+ 
AAA-server AuthInbound (outside) host 172.18.124.111 
cisco timeout 5
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
no sysopt route dnat
crypto ipsec transform-set myset ESP-Des esp-md5-hmac 
crypto dynamic-map dynmap 10 set transform-set myset
crypto map mymap 10 ipsec-isakmp dynamic dynmap
crypto map mymap client configuration address initiate
crypto map mymap client configuration address respond
crypto map mymap client authentication AuthInbound
crypto map mymap interface outside
isakmp enable outside
isakmp identity address
isakmp client configuration address-pool local test outside

!--- ISAKMP Policy for Cisco VPN Client 2.5 or !--- Cisco Secure VPN Client 1.1.

isakmp policy 10 authentication pre-share
isakmp policy 10 encryption des
isakmp policy 10 hash md5

!--- The 1.1 and 2.5 VPN Clients use Diffie-Hellman (D-H) !--- group 1 policy (PIX default).

isakmp policy 10 group 1
isakmp policy 10 lifetime 86400
! 

!--- ISAKMP Policy for VPN Client 3.0

isakmp policy 20 authentication pre-share
isakmp policy 20 encryption des
isakmp policy 20 hash md5

!--- The VPN 3.0 Clients use D-H group 2 policy !--- and PIX 6.0 code.

isakmp policy 20 group 2
isakmp policy 20 lifetime 86400
vpngroup vpn3000-all address-pool test
vpngroup vpn3000-all dns-server 10.1.1.40
vpngroup vpn3000-all wins-server 10.1.1.40
vpngroup vpn3000-all default-domain rtp.cisco.com
vpngroup vpn3000-all split-tunnel 108
vpngroup vpn3000-all idle-time 1800
vpngroup vpn3000-all password ********
vpngroup vpn3000-41 address-pool test
vpngroup vpn3000-41 split-tunnel 125
vpngroup vpn3000-41 idle-time 1800
vpngroup vpn3000-41 password ********
telnet timeout 5
ssh timeout 5
terminal width 80
Cryptochecksum:429db0e7d20451fc28074f4d6f990d25
: end

Xauth avec groupes VPN et listes de contrôle d'accès téléchargeables par utilisateur - Configuration ACS

Configuration de Cisco Secure ACS

Procédez comme suit :

1. Cliquez sur Interface Configuration et sélectionnez l'option pour User-Level Downloadable ACLs.

   

2. Cliquez sur Composants du profil partagé et définissez une liste de contrôle d'accès téléchargeable.

   

3. Cliquez sur User Setup. Sélectionnez l'option d'attribution de PIX ACL. Sélectionnez la liste de contrôle d’accès appropriée dans la liste déroulante.

   

Xauth avec groupes VPN et listes de contrôle d'accès téléchargeables par utilisateur - Installation de PIX 6.x

Si vous voulez effectuer une ACL téléchargeable utilisateur par utilisateur pour l'autorisation, utilisez le logiciel PIX Firewall version 6.2(2). Référez-vous à l'ID de bogue Cisco CSCdx47975 (clients enregistrés uniquement) .

PIX Version 6.2(2)
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
hostname sv2-4
fixup protocol ftp 21
fixup protocol http 80
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol ils 389
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol sip 5060
fixup protocol skinny 2000
names
access-list 108 permit ip 10.1.1.0 255.255.255.0 
192.168.1.0 255.255.255.0 
pager lines 24
logging buffered debugging
interface ethernet0 auto
interface ethernet1 auto
mtu outside 1500
mtu inside 1500
ip address outside 10.66.79.69 255.255.255.224
ip address inside 10.1.1.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool test 192.168.1.1-192.168.1.5
pdm history enable
arp timeout 14400
nat (inside) 0 access-list 108
conduit permit icmp any any 
route outside 0.0.0.0 0.0.0.0 10.66.79.65 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 
rpc 0:10:00 h323 0:05:00 sip 
0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+ 
aaa-server RADIUS protocol radius 
aaa-server LOCAL protocol local 
aaa-server AuthInbound protocol radius 
aaa-server AuthInbound (outside) host 10.66.79.244 cisco123 timeout 10
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
no sysopt route dnat
crypto ipsec transform-set myset esp-des esp-md5-hmac 
crypto dynamic-map dynmap 10 set transform-set myset
crypto map mymap 10 ipsec-isakmp dynamic dynmap

!--- This commands the router to respond to the VPN 3.x Client. 

crypto map mymap client configuration address respond

!--- This tells the router to expect Xauth for the VPN 3.x Client.
 
crypto map mymap client authentication AuthInbound
crypto map mymap interface outside
isakmp enable outside
isakmp policy 20 authentication pre-share
isakmp policy 20 encryption des
isakmp policy 20 hash md5
isakmp policy 20 group 2
isakmp policy 20 lifetime 86400
! 

!--- This is the VPN group configuration. 

vpngroup vpn3000-all address-pool test
vpngroup vpn3000-all default-domain apt.cisco.com

!--- The split-tunnel mode-config is not used, !--- which enforces authorization on a per-user basis. 

vpngroup vpn3000-all idle-time 1800
vpngroup vpn3000-all password ********
! 
telnet timeout 5
ssh timeout 5
terminal width 80
Cryptochecksum:7c3d067232f427e7522f4a679e963c58 
end:

Xauth avec groupes VPN et ACL téléchargeables par utilisateur - Configuration ASA/ PIX 7.x

PIX Version 7.1(1)
!
hostname PIX
domain-name cisco.com
enable password 9jNfZuG3TC5tCVH0 encrypted
names
!
interface Ethernet0
 nameif outside
 security-level 0
 ip address 10.66.79.69 255.255.255.224
!
interface Ethernet1
 nameif inside
 security-level 100
 ip address 10.1.1.1 255.255.255.0
!
passwd 2KFQnbNIdI.2KYOU encrypted
ftp mode passive
dns domain-lookup inside
dns server-group DefaultDNS
 timeout 30

access-list 108 permit ip 10.1.1.0 255.255.255.0 192.168.1.0 255.255.255.0
pager lines 24
logging buffer-size 500000
logging console debugging
logging monitor errors
mtu outside 1500
mtu inside 1500
ip local pool test 192.168.1.1-192.168.1.5
no failover
icmp permit any outside
icmp permit any inside
no asdm history enable
arp timeout 14400

nat (inside) 0 access-list 108
route outside 0.0.0.0 0.0.0.0 10.66.79.65 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00
timeout mgcp-pat 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute

aaa-server AuthInbound protocol radius
aaa-server AuthInbound host 10.66.79.244 key cisco123

group-policy vpn3000 internal
group-policy vpn3000 attributes
 dns-server value 172.16.1.1
 default-domain value cisco.com

username vpn3000 password nPtKy7KDCerzhKeX encrypted
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart

crypto ipsec transform-set my-set esp-des esp-md5-hmac

crypto dynamic-map dynmap 10 set transform-set my-set

crypto dynamic-map dynmap 10 set reverse-route

crypto map mymap 10 ipsec-isakmp dynamic dynmap

crypto map mymap interface outside

isakmp enable outside
isakmp policy 10 authentication pre-share
isakmp policy 10 encryption des
isakmp policy 10 hash md5
isakmp policy 10 group 2
isakmp policy 10 lifetime 1000

isakmp policy 65535 authentication pre-share
isakmp policy 65535 encryption 3des
isakmp policy 65535 hash sha
isakmp policy 65535 group 2
isakmp policy 65535 lifetime 86400


tunnel-group DefaultRAGroup general-attributes
 authentication-server-group (outside) vpn

tunnel-group vpn3000 type ipsec-ra
 
tunnel-group vpn3000 general-attributes
 address-pool test
 authentication-server-group vpn
 

tunnel-group vpn3000 ipsec-attributes
 pre-shared-key *

telnet timeout 5
ssh timeout 5
console timeout 0
!
class-map inspection_default
 match default-inspection-traffic
!
!
policy-map global_policy
 class inspection_default
  inspect dns maximum-length 512
  inspect ftp
  inspect h323 h225
  inspect h323 ras
  inspect netbios
  inspect rsh
  inspect rtsp
  inspect skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect tftp
  inspect sip
  inspect xdmcp
!
service-policy global_policy global
Cryptochecksum:ecb58c5d8ce805b3610b198c73a3d0cf
: end

Configuration de Xauth local pour la connexion du client VPN

Ces commandes sont requises pour configurer Xauth local pour la connexion du client VPN :

• aaa-server server-tag protocol local

• crypto map map-name client authentication aaa-server-name

Émettez la commande username pour définir les utilisateurs locaux sur PIX.

Afin d'utiliser la base de données d'authentification d'utilisateur PIX Firewall locale, entrez LOCAL pour le paramètre server-tag pour la commande aaa-server. La commande aaa-server est émise avec la commande crypto map pour établir une association d'authentification afin que les clients VPN soient authentifiés quand ils accèdent au pare-feu PIX.

Comment ajouter une comptabilité

Voici la syntaxe de la commande permettant d'ajouter la gestion des comptes :

• aaa accounting acctg_service|excepté entrant|sortant|if_name local_ip local_mask foreign_mask tacacs+|radius ;

ou (nouveauté de la section 5.2) :

• aaa accounting include acctg_service inbound|outbound match server_tag

Dans la configuration PIX, voici la commande ajoutée :

• aaa accounting include any inbound 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0.0 AuthInbound ;

ou (nouveauté de la section 5.2) :

• access-list 150 permit ip any any any accounting match 150 outside AuthInbound

Remarque : la commande sysopt connection permit-ipsec, et non la commande sysopt ipsec pl-compatible, est nécessaire au fonctionnement de la comptabilité Xauth. La gestion des comptes Xauth ne fonctionne pas uniquement avec la commande sysopt ipsec pl-compatible. La comptabilité Xauth est valide pour les connexions TCP. Il n'est pas valide pour les protocoles ICMP (Internet Control Message Protocol) ou UDP (User Datagram Protocol).

Exemple de comptabilité TACACS+

Fri Sep 8 03:48:40 2000 172.18.124.157 
pixc PIX 192.168.1.1 start task_id=0x17 foreign_ip=192.168.1.1 
    local_ip=10.1.1.40 cmd=telnet
Fri Sep 8 03:48:44 2000 172.18.124.157 pixc PIX 192.168.1.1 
    stop task_id=0x17 foreign_ip=192.168.1.1 local_ip=10.1.1.40 
    cmd=telnet elapsed_time=4 bytes_in=42 bytes_out=103
Fri Sep 8 03:49:31 2000 172.18.124.157 pixc PIX 192.168.1.1 
    start task_id=0x18 
foreign_ip=192.168.1.1 local_ip=10.1.1.40 cmd=http
Fri Sep 8 03:49:35 2000 172.18.124.157 pixc PIX 192.168.1.1 
    stop task_id=0x18 foreign_ip=192.168.1.1 local_ip=10.1.1.40 
    cmd=http elapsed_time=4 bytes_in=242 bytes_out=338

Exemple de comptabilisation RADIUS

Acct-Status-Type = Start
NAS-IP-Address = 172.18.124.157
Login-IP-Host = 10.1.1.40
Login-TCP-Port = 23
Acct-Session-Id = 0x00000003
User-Name = noacl
Vendor-Specific = Source-IP=192.168.1.1
Vendor-Specific = Source-Port=1141
Vendor-Specific = Destination-IP=10.1.1.40
Vendor-Specific = Destination-Port=23

Acct-Status-Type = Start
NAS-IP-Address = 172.18.124.157
Login-IP-Host = 10.1.1.40
Login-TCP-Port = 80
Acct-Session-Id = 0x00000004
User-Name = noacl
Vendor-Specific = Source-IP=192.168.1.1
Vendor-Specific = Source-Port=1168
Vendor-Specific = Destination-IP=10.1.1.40
Vendor-Specific = Destination-Port=80

Acct-Status-Type = Stop
NAS-IP-Address = 172.18.124.157
Login-IP-Host = 10.1.1.41
Login-TCP-Port = 80
Acct-Session-Id = 0x00000008
User-Name = noacl
Acct-Session-Time = 4
Acct-Input-Octets = 242
Acct-Output-Octets = 338
Vendor-Specific = Source-IP=192.168.1.1
Vendor-Specific = Source-Port=1182
Vendor-Specific = Destination-IP=10.1.1.41
Vendor-Specific = Destination-Port=80

Acct-Status-Type = Stop
NAS-IP-Address = 172.18.124.157
Login-IP-Host = 10.1.1.40
Login-TCP-Port = 23
Acct-Session-Id = 0x00000015
User-Name = noacl
Acct-Session-Time = 33
Acct-Input-Octets = 43
Acct-Output-Octets = 103
Vendor-Specific = Source-IP=192.168.1.1
Vendor-Specific = Source-Port=1257
Vendor-Specific = Destination-IP=10.1.1.40
Vendor-Specific = Destination-Port=23

Debug and Show - Xauth sans groupes VPN

goss-pixb#show debug
debug crypto ipsec 1
debug crypto isakmp 1
debug crypto engine
debug fover status
tx Off
rx Off
open Off
cable Off
txdmp Off
rxdmp Off
ifc Off
rxip Off
txip Off
get Off
put Off
verify Off
switch Off
fail Off
fmsg Off
goss-pixb#terminal monitor
goss-pixb# 

crypto_isakmp_process_block: src 172.18.124.99, dest 172.18.124.157
OAK_MM exchange
ISAKMP (0): processing SA payload. message ID = 0

ISAKMP (0): Checking ISAKMP transform 1 against priority 10 policy
ISAKMP: encryption DES-CBC
ISAKMP: hash MD5
ISAKMP: default group 1
ISAKMP: auth pre-share
ISAKMP (0): atts are acceptable. Next payload is 0
ISAKMP (0): SA is doing pre-shared key authentication
using id type ID_IPV4_ADDR
return status is IKMP_NO_ERROR
crypto_isakmp_process_block: src 172.18.124.99, dest 172.18.124.157
OAK_MM exchange
ISAKMP (0): processing KE payload. Message ID = 0

ISAKMP (0): processing NONCE payload. Message ID = 0

ISAKMP (0): processing vendor id payload

ISAKMP (0): processing vendor id payload

return status is IKMP_NO_ERROR
crypto_isakmp_process_block: src 172.18.124.99, dest 172.18.124.157
OAK_MM exchange
ISAKMP (0): processing ID payload. Message ID = 0
ISAKMP (0): processing HASH payload. Message ID = 0
ISAKMP (0): processing NOTIFY payload 24578 protocol 1
spi 0, message ID = 0
ISAKMP (0): processing notify INITIAL_CONTACTIPSEC(key_engine): 
got a queue event...
IPSEC(key_engine_delete_sas): rec'd delete notify from ISAKMP
IPSEC(key_engine_delete_sas): delete all SAs shared with 172.18.124.99

ISAKMP (0): SA has been authenticated

ISAKMP (0): ID payload
next-payload : 8
type : 1
protocol : 17
port : 500
length : 8
ISAKMP (0): Total payload length: 12
return status is IKMP_NO_ERROR
crypto_isakmp_process_block: src 172.18.124.99, dest 172.18.124.157
OAK_QM exchange
ISAKMP (0:0): Need XAUTH
ISAKMP/xauth: request attribute XAUTH_TYPE
ISAKMP/xauth: request attribute XAUTH_USER_NAME
ISAKMP/xauth: request attribute XAUTH_USER_PASSWORD
ISAKMP (0:0): initiating peer config to 172.18.124.99. 
ID = 2218162690 (0x84367a02)
return status is IKMP_NO_ERROR
crypto_isakmp_process_block: src 172.18.124.99, dest 172.18.124.157
ISAKMP_TRANSACTION exchange
ISAKMP (0:0): processing transaction payload from 172.18.124.99. 
Message ID = 2156074032
ISAKMP: Config payload CFG_REPLY
return status is IKMP_ERR_NO_RETRANS109005: Authentication succeeded 
for user 'pixb' from 172.18.124.99/0 to 0.0.0.0/0 on 
interface IKE-XAUTH
ISAKMP (0:0): initiating peer config to 172.18.124.99. 
ID = 2218162690 (0x84367a02)
109005: Authentication succeeded for user 'pixb' from 172.18.124.157
crypto_isakmp_process_block: src 172.18.124.99, dest 172.18.124.157
ISAKMP_TRANSACTION exchange
ISAKMP (0:0): processing transaction payload from 172.18.124.99. 
Message ID = 2156497080
ISAKMP: Config payload CFG_ACK
ISAKMP (0:0): initiating peer config to 172.18.124.99. 
ID = 393799466 (0x1778e72a)
return status is IKMP_NO_ERROR
crypto_isakmp_process_block: src 172.18.124.99, dest 172.18.124.157
ISAKMP_TRANSACTION exchange
ISAKMP (0:0): processing transaction payload from 172.18.124.99. 
Message ID = 2156156112
ISAKMP: Config payload CFG_ACK
ISAKMP (0:0): peer accepted the address!
return status is IKMP_NO_ERROR.99/0 to 0.0.0.0/0 on 
interface IKE-XAUTH

crypto_isakmp_process_block: src 172.18.124.99, dest 172.18.124.157
OAK_QM exchange
oakley_process_quick_mode:
OAK_QM_IDLE
ISAKMP (0): processing SA payload. Message ID = 2323118710

ISAKMP : Checking IPSec proposal 1

ISAKMP: transform 1, ESP_DES
ISAKMP: attributes in transform:
ISAKMP: authenticator is HMAC-MD5
ISAKMP: encaps is 1
ISAKMP (0): atts are acceptable.IPSEC(validate_proposal_request): 
proposal part #1,
(key eng. msg.) dest= 172.18.124.157, src= 172.18.124.99, 
dest_proxy= 10.1.1.0/255.255.255.0/0/0 (type=4), 
src_proxy= 192.168.1.1/255.255.255.255/0/0 (type=1),
protocol= ESP, transform= ESP-Des esp-md5-hmac , 
lifedur= 0s and 0kb, 
spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x4

ISAKMP (0): processing NONCE payload. Message ID = 2323118710

ISAKMP (0): processing ID payload. Message ID = 2323118710
ISAKMP (0): ID_IPV4_ADDR src 192.168.1.1 prot 0 port 0
ISAKMP (0): processing ID payload. Message ID = 2323118710
ISAKMP (0): ID_IPV4_ADDR_SUBNET dst 10.1.1.0/255.255.255.0 
prot 0 port 0
IPSEC(key_engine): got a queue event...
IPSEC(spi_response): getting spi 0xeeae8930(4004415792) for SA 
from 172.18.124.99 to 172.18.124.157 for prot 3

return status is IKMP_NO_ERROR4
crypto_isakmp_process_block: src 172.18.124.99, dest 172.18.124.157
OAK_QM exchange
oakley_process_quick_mode:
OAK_QM_AUTH_AWAITmap_alloc_entry: allocating entry 1
map_alloc_entry: allocating entry 2

ISAKMP (0): Creating IPSec SAs
inbound SA from 172.18.124.99 to 172.18.124.157 
(proxy 192.168.1.1 to 10.1.1.0)
has spi 4004415792 and conn_id 1 and flags 4
outbound SA from 172.18.124.157 to 172.18.124.99 
(proxy 10.1.1.0 to 192.168.1.1)
has spi 1281287211 and conn_id 2 and flags 4
IPSEC(key_engine): got a queue event...
IPSEC(initialize_sas): ,
(key eng. msg.) dest= 172.18.124.157, src= 172.18.124.99, 
dest_proxy= 10.1.1.0/255.255.255.0/0/0 (type=4), 
src_proxy= 192.168.1.1/0.0.0.0/0/0 (type=1),
protocol= ESP, transform= esp-des esp-md5-hmac , 
lifedur= 0s and 0kb, 
spi= 0xeeae8930(4004415792), conn_id= 1, keysize= 0, flags= 0x4
IPSEC(initialize_sas): ,
(key eng. msg.) src= 172.18.124.157, dest= 172.18.124.99, 
src_proxy= 10.1.1.0/255.255.255.0/0/0 (type=4), 
dest_proxy= 192.168.1.1/0.0.0.0/0/0 (type=1),
protocol= ESP, transform= esp-des esp-md5-hmac , 
lifedur= 0s and 0kb, 
spi= 0x4c5ee42b(1281287211), conn_id= 2, keysize= 0, flags= 0x4

return status is IKMP_NO_ERROR02101: decaps: rec'd 
IPSEC packet has invalid spi for destaddr=172.18.124.157, 
prot=esp, spi=0xeeae8930(0)
602301: sa created, (sa) sa_dest= 172.18.124.157, sa_prot= 50, 
sa_spi= 0xeeae8930(4004415792), sa_trans= esp-des esp-md5-hmac,
 sa_conn_id= 1

602301: sa created, (sa) sa_dest= 172.18.124.99, sa_prot= 50, 
sa_spi= 0x4c5ee42b(1281287211), sa_trans= esp-des esp-md5-hmac,
 sa_conn_id= 2

109011: Authen Session Start: user 'pixb', sid 5
109015: Authorization denied (acl=115) for user 'pixb' from 
192.168.1.1/0 to 10.1.1.40/8 on interface outside
109015: Authorization denied (acl=115) for user 'pixb' from 
192.168.1.1/0 to 10.1.1.40/8 on interface outside
109015: Authorization denied (acl=115) for user 'pixb' from 
192.168.1.1/0 to 10.1.1.40/8 on interface outside
109015: Authorization denied (acl=115) for user 'pixb' from 
192.168.1.1/0 to 10.1.1.40/8 on interface outside

goss-pixb# 
goss-pixb#show uauth
Current Most Seen
Authenticated Users 1 1
Authen In Progress 0 1
ipsec user 'pixb' at 192.168.1.1, authenticated
access-list 115
goss-pixb#show access-list
access-list 108 permit ip 10.1.1.0 255.255.255.0 192.168.1.0 
255.255.255.0 (hitcnt=18) 
access-list 125 permit ip host 10.1.1.41 any (hitcnt=0) 
access-list dynacl4 permit ip 10.1.1.0 255.255.255.0 host 
192.168.1.1 (hitcnt=0) 
access-list 115 permit ip any host 10.1.1.41 (hitcnt=0) 
access-list 115 deny ip any host 10.1.1.42 (hitcnt=0)

Debug and Show - Xauth avec groupes VPN

crypto_isakmp_process_block: src 172.18.124.96, 
dest 172.18.124.157
goss-pixb#show debug
debug crypto ipsec 1
debug crypto isakmp 1
debug crypto engine
debug fover status
tx Off
rx Off
open Off
cable Off
txdmp Off
rxdmp Off
ifc Off
rxip Off
txip Off
get Off
put Off
verify Off
switch Off
fail Off
fmsg Off
goss-pixb# 
crypto_isakmp_process_block: src 172.18.124.99, dest 172.18.124.157
OAK_AG exchange
ISAKMP (0): processing SA payload. message ID = 0

ISAKMP (0): Checking ISAKMP transform 1 against priority 10 policy
ISAKMP: encryption DES-CBC
ISAKMP: hash MD5
ISAKMP: default group 1
ISAKMP: auth pre-share
ISAKMP (0): atts are acceptable. Next payload is 3
ISAKMP (0): processing KE payload. message ID = 0

ISAKMP (0): processing NONCE payload. message ID = 0

ISAKMP (0): processing ID payload. message ID = 0
ISAKMP (0): processing vendor id payload

ISAKMP (0): speaking to a VPN3000 client

ISAKMP (0): ID payload
next-payload : 10
type : 1
protocol : 17
port : 500
length : 8
ISAKMP (0): Total payload length: 12
return status is IKMP_NO_ERROR
crypto_isakmp_process_block: src 172.18.124.99, dest 172.18.124.157
OAK_AG exchange
ISAKMP (0): processing HASH payload. message ID = 0
ISAKMP (0): SA has been authenticated
return status is IKMP_NO_ERROR
crypto_isakmp_process_block: src 172.18.124.99, dest 172.18.124.157
OAK_QM exchange
ISAKMP (0:0): Need XAUTH
ISAKMP/xauth: request attribute XAUTH_TYPE
ISAKMP/xauth: request attribute XAUTH_USER_NAME
ISAKMP/xauth: request attribute XAUTH_USER_PASSWORD
ISAKMP (0:0): initiating peer config to 172.18.124.99. 
ID = 1396280702 (0x53398d7e)
return status is IKMP_NO_ERROR
crypto_isakmp_process_block: src 172.18.124.99, dest 172.18.124.157
ISAKMP_TRANSACTION exchange
ISAKMP (0:0): processing transaction payload from 172.18.124.99. 
message ID = 2156608344
ISAKMP: Config payload CFG_REPLY
return status is IKMP_ERR_NO_RETRANS10
ISAKMP (0:0): initiating peer config to 172.18.124.99. 
ID = 1396280702 (0x53398d7e)9
crypto_isakmp_process_block: src 172.18.124.99, dest 172.18.124.157
ISAKMP_TRANSACTION exchange
ISAKMP (0:0): processing transaction payload from 172.18.124.99. 
message ID = 2156115984
ISAKMP: Config payload CFG_ACK
ISAKMP (0:0): peer accepted the address!
ISAKMP (0:0): processing saved QM.
oakley_process_quick_mode:
OAK_QM_IDLE
ISAKMP (0): processing SA payload. message ID = 1697984837

ISAKMP : Checking IPSec proposal 1

ISAKMP: transform 1, ESP_DES
ISAKMP: attributes in transform:
ISAKMP: authenticator is HMAC-MD5
ISAKMP: encaps is 1
ISAKMP (0): atts are acceptable.
IPSEC(validate_proposal_request): proposal part #1,
(key eng. msg.) dest= 172.18.124.157, src= 172.18.124.99, 
dest_proxy= 172.18.124.157/255.255.255.255/0/0 (type=1), 
src_proxy= 192.168.1.1/255.255.255.255/0/0 (type=1),
protocol= ESP, transform= esp-des esp-md5-hmac , 
lifedur= 0s and 0kb, 
spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x4

ISAKMP (0): processing NONCE payload. message ID = 1697984837

ISAKMP (0): processing ID payload. message ID = 1697984837
ISAKMP (0): ID_IPV4_ADDR src 192.168.1.1 prot 0 port 0
ISAKMP (0): processing ID payload. message ID = 1697984837
ISAKMP (0): ID_IPV4_ADDR dst 172.18.124.157 prot 0 port 0
ISAKMP (0): processing NOTIFY payload 24578 protocol 1
spi 0, message ID = 1697984837
ISAKMP (0): processing notify INITIAL_CONTACTIPSEC(key_engine): 
got a queue event...
IPSEC(key_engine_delete_sas): rec'd delete notify from ISAKMP
IPSEC(key_engine_delete_sas): delete all SAs shared with 172.18.124.99
IPSEC(key_engine): got a queue event...
IPSEC(spi_response): getting spi 0x6a9d3f79(1788690297) for SA 
from 172.18.124.99 to 172.18.124.157 for prot 3

return status is IKMP_NO_ERROR0
crypto_isakmp_process_block: src 172.18.124.99, dest 172.18.124.157
OAK_QM exchange
oakley_process_quick_mode:
OAK_QM_AUTH_AWAITmap_alloc_entry: allocating entry 1
map_alloc_entry: allocating entry 2

ISAKMP (0): Creating IPSec SAs
inbound SA from 172.18.124.99 to 172.18.124.157 
(proxy 192.168.1.1 to 172.18.124.157)
has spi 1788690297 and conn_id 1 and flags 4
outbound SA from 172.18.124.157 to 172.18.124.99 
(proxy 172.18.124.157 to 192.168.1.1)
has spi 2854452814 and conn_id 2 and flags 4
IPSEC(key_engine): got a queue event...
IPSEC(initialize_sas): ,
(key eng. msg.) dest= 172.18.124.157, src= 172.18.124.99, 
dest_proxy= 172.18.124.157/0.0.0.0/0/0 (type=1), 
src_proxy= 192.168.1.1/0.0.0.0/0/0 (type=1),
protocol= ESP, transform= esp-des esp-md5-hmac , 
lifedur= 0s and 0kb, 
spi= 0x6a9d3f79(1788690297), conn_id= 1, keysize= 0, flags= 0x4
IPSEC(initialize_sas): ,
(key eng. msg.) src= 172.18.124.157, dest= 172.18.124.99, 
src_proxy= 172.18.124.157/0.0.0.0/0/0 (type=1), 
dest_proxy= 192.168.1.1/0.0.0.0/0/0 (type=1),
protocol= ESP, transform= esp-des esp-md5-hmac , 
lifedur= 0s and 0kb, 
spi= 0xaa237e4e(2854452814), conn_id= 2, keysize= 0, flags= 0x4

return status is IKMP_NO_ERROR05: Authentication succeeded 
for user 'pixc' from 172.18.124.99/0 to 0.0.0.0/0 on interface IKE-XAUTH
602301: sa created, (sa) sa_dest= 172.18.124.157, sa_prot= 50, 
sa_spi= 0x6a9d3f79(1788690297), sa_trans= esp-des esp-md5-hmac , 
sa_conn_id= 1

602301: sa created, (sa) sa_dest= 172.18.124.99, sa_prot= 50, 
sa_spi= 0xaa237e4e(2854452814), sa_trans= esp-des esp-md5-hmac , 
sa_conn_id= 2

109011: Authen Session Start: user 'pixc', sid 19

crypto_isakmp_process_block: src 172.18.124.99, dest 172.18.124.157
OAK_QM exchange
oakley_process_quick_mode:
OAK_QM_IDLE
ISAKMP (0): processing SA payload. message ID = 3361949217

ISAKMP : Checking IPSec proposal 1

ISAKMP: transform 1, ESP_DES
ISAKMP: attributes in transform:
ISAKMP: authenticator is HMAC-MD5
ISAKMP: encaps is 1
ISAKMP (0): atts are acceptable.
IPSEC(validate_proposal_request): proposal part #1,
(key eng. msg.) dest= 172.18.124.157, src= 172.18.124.99, 
dest_proxy= 10.1.1.0/255.255.255.0/0/0 (type=4), 
src_proxy= 192.168.1.1/255.255.255.255/0/0 (type=1),
protocol= ESP, transform= esp-des esp-md5-hmac , 
lifedur= 0s and 0kb, 
spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x4

ISAKMP (0): processing NONCE payload. message ID = 3361949217

ISAKMP (0): processing ID payload. message ID = 3361949217
ISAKMP (0): ID_IPV4_ADDR src 192.168.1.1 prot 0 port 0
ISAKMP (0): processing ID payload. message ID = 3361949217
ISAKMP (0): ID_IPV4_ADDR_SUBNET dst 10.1.1.0/255.255.255.0 prot 0 port 0
IPSEC(key_engine): got a queue event...
IPSEC(spi_response): getting spi 0xfec4c3aa(4274308010) for SA 
from 172.18.124.99 to 172.18.124.157 for prot 3

return status is IKMP_NO_ERROR4
crypto_isakmp_process_block: src 172.18.124.99, dest 172.18.124.157
OAK_QM exchange
oakley_process_quick_mode:
OAK_QM_AUTH_AWAITmap_alloc_entry: allocating entry 4
map_alloc_entry: allocating entry 3

ISAKMP (0): Creating IPSec SAs
inbound SA from 172.18.124.99 to 172.18.124.157 
(proxy 192.168.1.1 to 10.1.1.0)
has spi 4274308010 and conn_id 4 and flags 4
outbound SA from 172.18.124.157 to 172.18.124.99 
(proxy 10.1.1.0 to 192.168.1.1)
has spi 798459812 and conn_id 3 and flags 4
IPSEC(key_engine): got a queue event...
IPSEC(initialize_sas): ,
(key eng. msg.) dest= 172.18.124.157, src= 172.18.124.99, 
dest_proxy= 10.1.1.0/255.255.255.0/0/0 (type=4), 
src_proxy= 192.168.1.1/0.0.0.0/0/0 (type=1),
protocol= ESP, transform= esp-des esp-md5-hmac , 
lifedur= 0s and 0kb, 
spi= 0xfec4c3aa(4274308010), conn_id= 4, keysize= 0, flags= 0x4
IPSEC(initialize_sas): ,
(key eng. msg.) src= 172.18.124.157, dest= 172.18.124.99, 
src_proxy= 10.1.1.0/255.255.255.0/0/0 (type=4), 
dest_proxy= 192.168.1.1/0.0.0.0/0/0 (type=1),
protocol= ESP, transform= esp-des esp-md5-hmac , 
lifedur= 0s and 0kb, 
spi= 0x2f9787a4(798459812), conn_id= 3, keysize= 0, flags= 0x4

return status is IKMP_NO_ERROR02101: decaps: rec'd IPSEC 
packet has invalid spi for destaddr=172.18.124.157, prot=esp, 
spi=0xfec4c3aa(0)
602301: sa created, (sa) sa_dest= 172.18.124.157, sa_prot= 50, 
sa_spi= 0xfec4c3aa(4274308010), sa_trans= esp-des esp-md5-hmac , 
sa_conn_id= 4

602301: sa created, (sa) sa_dest= 172.18.124.99, sa_prot= 50, 
sa_spi= 0x2f9787a4(798459812), sa_trans= esp-des esp-md5-hmac , 
sa_conn_id= 3


goss-pixb#show uauth
Current Most Seen
Authenticated Users 1 1
Authen In Progress 0 1
ipsec user 'pixc' at 192.168.1.1, authenticated
goss-pixb#show crypto ipsec sa


interface: outside
Crypto map tag: mymap, local addr. 172.18.124.157

local ident (addr/mask/prot/port): (172.18.124.157/255.255.255.255/0/0)
remote ident (addr/mask/prot/port): (192.168.1.1/255.255.255.255/0/0)
current_peer: 172.18.124.99
dynamic allocated peer ip: 192.168.1.1

PERMIT, flags={}
#pkts encaps: 0, #pkts encrypt: 0, #pkts digest 0
#pkts decaps: 0, #pkts decrypt: 0, #pkts verify 0
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts compr. failed: 0, 
#pkts decompress failed: 0
#send errors 0, #recv errors 0

local crypto endpt.: 172.18.124.157, remote crypto endpt.: 172.18.124.99
path mtu 1500, ipsec overhead 56, media mtu 1500
current outbound spi: aa237e4e

inbound esp sas:
spi: 0x6a9d3f79(1788690297)
transform: esp-des esp-md5-hmac ,
<--- More ---> in use settings ={Tunnel, }
slot: 0, conn id: 1, crypto map: mymap
sa timing: remaining key lifetime (k/sec): (4608000/28519)
IV size: 8 bytes
replay detection support: Y


inbound ah sas:


inbound pcp sas:


outbound esp sas:
spi: 0xaa237e4e(2854452814)
transform: esp-des esp-md5-hmac ,
in use settings ={Tunnel, }
slot: 0, conn id: 2, crypto map: mymap
sa timing: remaining key lifetime (k/sec): (4608000/28510)
IV size: 8 bytes
replay detection support: Y


outbound ah sas:
<--- More ---> 

outbound pcp sas:



local ident (addr/mask/prot/port): (10.1.1.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (192.168.1.1/255.255.255.255/0/0)
current_peer: 172.18.124.99
dynamic allocated peer ip: 192.168.1.1

PERMIT, flags={}
#pkts encaps: 4, #pkts encrypt: 4, #pkts digest 4
#pkts decaps: 4, #pkts decrypt: 4, #pkts verify 4
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts compr. failed: 0, 
#pkts decompress failed: 0
#send errors 0, #recv errors 0

local crypto endpt.: 172.18.124.157, remote crypto 
endpt.:172.18.124.99
path mtu 1500, ipsec overhead 56, media mtu 1500
current outbound spi: 2f9787a4

inbound esp sas:
spi: 0xfec4c3aa(4274308010)
<--- More ---> transform: esp-des esp-md5-hmac ,
in use settings ={Tunnel, }
slot: 0, conn id: 4, crypto map: mymap
sa timing: remaining key lifetime (k/sec): (4607999/27820)
IV size: 8 bytes
replay detection support: Y


inbound ah sas:


inbound pcp sas:


outbound esp sas:
spi: 0x2f9787a4(798459812)
transform: esp-des esp-md5-hmac ,
in use settings ={Tunnel, }
slot: 0, conn id: 3, crypto map: mymap
sa timing: remaining key lifetime (k/sec): (4607999/27820)
IV size: 8 bytes
replay detection support: Y


<--- More ---> outbound ah sas:


outbound pcp sas:

Debug and Show - Xauth avec ACL téléchargeables par utilisateur

crypto_isakmp_process_block: src 10.66.79.229, 
dest 10.66.79.69
VPN Peer: ISAKMP: Added new peer: ip:10.66.79.229 
Total VPN Peers:1
VPN Peer: ISAKMP: Peer ip:10.66.79.229 Ref cnt incremented to:1 
Total VPN Peers:1
OAK_AG exchange
ISAKMP (0): processing SA payload. message ID = 0

ISAKMP (0): Checking ISAKMP transform 1 against priority 20 policy
ISAKMP: encryption 3DES-CBC
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: extended auth pre-share
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x20 0xc4 0x9b 
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): Checking ISAKMP transform 2 against priority 20 policy
ISAKMP: encryption 3DES-CBC
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: extended auth pre-share
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x20 0xc4 0x9b 
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): Checking ISAKMP transform 3 against priority 20 policy
ISAKMP: encryption 3DES-CBC
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: auth pre-share
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x20 0xc4 0x9b 
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): Checking ISAKMP transform 4 against priority 20 policy
ISAKMP: encryption 3DES-CBC
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: auth pre-share
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x20 0xc4 0x9b 
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): Checking ISAKMP transform 5 against priority 20 policy
ISAKMP: encryption DES-CBC
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: extended auth pre-share
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x20 0xc4 0x9b 
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): Checking ISAKMP transform 6 against priority 20 policy
ISAKMP: encryption DES-CBC
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: extended auth pre-share
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x20 0xc4 0x9b 
ISAKMP (0): atts are acceptable. Next payload is 3
ISAKMP (0): processing KE payload. message ID = 0

ISAKMP (0): processing NONCE payload. message ID = 0

ISAKMP (0): processing ID payload. message ID = 0
ISAKMP (0): processing vendor id payload

ISAKMP (0): received xauth v6 vendor id

ISAKMP (0): processing vendor id payload

ISAKMP (0): remote peer supports dead peer detection

ISAKMP (0): processing vendor id payload

ISAKMP (0): speaking to a Unity client

ISAKMP (0): ID payload
next-payload : 10
type : 2
protocol : 17
port : 500
length : 10
ISAKMP (0): Total payload length: 14
return status is IKMP_NO_ERROR
crypto_isakmp_process_block: src 10.66.79.229, dest 10.66.79.69
OAK_AG exchange
ISAKMP (0): processing HASH payload. message ID = 0
ISAKMP (0): processing NOTIFY payload 24578 protocol 1
spi 0, message ID = 0RADIUS_GET_PASS
RADIUS_REQUEST
raidus.c: rad_mkpkt_authen
attribute:
type 1, length 10, content:
80917fb0: 74 65 73 74 75 73 65 72 | testuser
attribute:
type 4, length 6, content:
80917fb0: 0a 42 | .B
80917fc0: 4f 45 | OE
attribute:
type 5, length 6, content:
80917fd0: 00 00 00 01 | ....

ISAKMP (0): processing notify INITIAL_CONTACTrip 0x80791f00
: chall_state ''
: state 0x7
: timer 0x0
: info 0x5d5ba513
session_id 0x5d5ba513
request_id 0x2
user 'testuser'
app 0
reason 2
sip 10.66.79.244
type 1
rad_procpkt: ACCEPT
attribute:
type 8, length 6, content:
809186f0: ff ff | ..
80918700: ff ff | ..
RADIUS_RCVD
attribute:
type 26, length 67, content:
Vendor ID 0 0 0 9, type=1, len=61:
80918700: 41 43 53 3a 43 69 | ACS:Ci
80918710: 73 63 6f 53 65 63 75 72 65 2d 44 65 66 69 6e 65 
| scoSecure-Define
80918720: 64 2d 41 43 4c 3d 23 41 43 53 41 43 4c 23 2d 50 
| d-ACL=#ACSACL#-P
80918730: 49 58 2d 56 50 4e 43 6c 69 65 6e 74 2d 33 64 33 
| IX-VPNClient-3d3
80918740: 32 37 38 31 35 | 27815
RADIUS_RCVD
RADIUS_REQUEST
raidus.c: rad_mkpkt_authen
attribute:
type 1, length 33, content:
809186d0: 23 41 43 53 41 43 4c 23 2d 50 49 58 | #ACSACL#-PIX
809186e0: 2d 56 50 4e 43 6c 69 65 6e 74 2d 33 64 33 32 37 
| -VPNClient-3d327
809186f0: 38 31 35 | 815
attribute:
type 4, length 6, content:
809186f0: 0a 42 4f 45 | .BOE
attribute:
type 5, length 6, content:
80918700: 00 00 00 | ...
80918710: 02 | .
IPSEC(key_engine): got a queue event...rip 0x80791f00
: chall_state ''
: state 0x7
: timer 0x0
: info 0x5d5ba513
session_id 0x5d5ba513
request_id 0x3
user '#ACSACL#-PIX-VPNClient-3d327815'
app 0
reason 2
sip 10.66.79.244
type 1
rad_procpkt: ACCEPT
attribute:
type 26, length 46, content:
Vendor ID 0 0 0 9, type=1, len=40:
80918e20: 69 70 3a 69 6e 61 63 6c 23 31 3d 70 | ip:inacl#1=p
80918e30: 65 72 6d 69 74 20 69 70 20 61 6e 79 20 68 6f 73 
| ermit ip any hos
80918e40: 74 20 31 30 2e 31 2e 31 2e 32 | t 10.1.1.2
RADIUS_RCVD
RADIUS_RCVD
RADIUS_ACCESS_ACCEPT:normal termination
RADIUS_DELETE

IPSEC(key_engine_delete_sas): rec'd delete notify from ISAKMP
IPSEC(key_engine_delete_sas): delete all SAs shared with 10.66.79.229

ISAKMP (0): SA has been authenticated
return status is IKMP_NO_ERROR
ISAKMP (0): sending phase 1 RESPONDER_LIFETIME notify
ISAKMP (0): sending NOTIFY message 24576 protocol 1
ISAKMP/xauth: request attribute XAUTH_TYPE
ISAKMP/xauth: request attribute XAUTH_USER_NAME
ISAKMP/xauth: request attribute XAUTH_USER_PASSWORD
ISAKMP (0:0): initiating peer config to 10.66.79.229. 
ID = 3250273953 (0xc1bb3ea1)
crypto_isakmp_process_block: src 10.66.79.229, dest 10.66.79.69
ISAKMP_TRANSACTION exchange
ISAKMP (0:0): processing transaction payload from 10.66.79.229.
 message ID = 2167001532
ISAKMP: Config payload CFG_REPLY
return status is IKMP_ERR_NO_RETRANS
ISAKMP (0:0): initiating peer config to 10.66.79.229. 
ID = 1530000247 (0x5b31f377)
crypto_isakmp_process_block: src 10.66.79.229, dest 10.66.79.69
ISAKMP_TRANSACTION exchange
ISAKMP (0:0): processing transaction payload from 10.66.79.229. 
message ID = 2167001532
ISAKMP: Config payload CFG_ACK
return status is IKMP_NO_ERROR
crypto_isakmp_process_block: src 10.66.79.229, dest 10.66.79.69
ISAKMP_TRANSACTION exchange
ISAKMP (0:0): processing transaction payload from 10.66.79.229. 
message ID = 2167001532
ISAKMP: Config payload CFG_REQUEST
ISAKMP (0:0): checking request:
ISAKMP: attribute IP4_ADDRESS (1)
ISAKMP: attribute IP4_NETMASK (2)
ISAKMP: attribute IP4_DNS (3)
ISAKMP: attribute IP4_NBNS (4)
ISAKMP: attribute ADDRESS_EXPIRY (5)
Unsupported Attr: 5
ISAKMP: attribute APPLICATION_VERSION (7)
Unsupported Attr: 7
ISAKMP: attribute UNKNOWN (28672)
Unsupported Attr: 28672
ISAKMP: attribute UNKNOWN (28673)
Unsupported Attr: 28673
ISAKMP: attribute ALT_DEF_DOMAIN (28674)
ISAKMP: attribute ALT_SPLIT_INCLUDE (28676)
ISAKMP: attribute ALT_PFS (28679)
ISAKMP: attribute UNKNOWN (28680)
Unsupported Attr: 28680
ISAKMP: attribute UNKNOWN (28677)
Unsupported Attr: 28677
ISAKMP (0:0): responding to peer config from 10.66.79.229. 
ID = 2397668523
return status is IKMP_NO_ERROR
crypto_isakmp_process_block: src 10.66.79.229, dest 10.66.79.69
OAK_QM exchange
oakley_process_quick_mode:
OAK_QM_IDLE
ISAKMP (0): processing SA payload. message ID = 2858414843

ISAKMP : Checking IPSec proposal 1

ISAKMP: transform 1, ESP_3DES
ISAKMP: attributes in transform:
ISAKMP: authenticator is HMAC-MD5
ISAKMP: encaps is 1
ISAKMP: SA life type in seconds
ISAKMP: SA life duration (VPI) of 0x0 0x20 0xc4 0x9b 
IPSEC(validate_proposal): transform proposal 
(prot 3, trans 3, hmac_alg 1) not supported

ISAKMP (0): atts not acceptable. Next payload is 0
ISAKMP (0): skipping next ANDed proposal (1)
ISAKMP : Checking IPSec proposal 2

ISAKMP: transform 1, ESP_3DES
ISAKMP: attributes in transform:
ISAKMP: authenticator is HMAC-SHA
ISAKMP: encaps is 1
ISAKMP: SA life type in seconds
ISAKMP: SA life duration (VPI) of 0x0 0x20 0xc4 0x9b 
IPSEC(validate_proposal): transform proposal 
(prot 3, trans 3, hmac_alg 2) not supported

ISAKMP (0): atts not acceptable. Next payload is 0
ISAKMP (0): skipping next ANDed proposal (2)
ISAKMP : Checking IPSec proposal 3

ISAKMP: transform 1, ESP_3DES
ISAKMP: attributes in transform:
ISAKMP: authenticator is HMAC-MD5
ISAKMP: encaps is 1
ISAKMP: SA life type in seconds
ISAKMP: SA life duration (VPI) of 0x0 0x20 0xc4 0x9b IPSEC
(validate_proposal): transform proposal (prot 3, trans 3, hmac_alg 1) 
not supported

ISAKMP (0): atts not acceptable. Next payload is 0
ISAKMP : Checking IPSec proposal 4

ISAKMP: transform 1, ESP_3DES
ISAKMP: attributes in transform:
ISAKMP: authenticator is HMAC-SHA
ISAKMP: encaps is 1
ISAKMP: SA life type in seconds
ISAKMP: SA life duration (VPI) of 0x0 0x20 0xc4 0x9b IPSEC
(validate_proposal): transform proposal (prot 3, trans 3, hmac_alg 2) 
not supported

ISAKMP (0): atts not acceptable. Next payload is 0
ISAKMP : Checking IPSec proposal 5

ISAKMP: transform 1, ESP_DES
ISAKMP: attributes in transform:
ISAKMP: authenticator is HMAC-MD5
ISAKMP: encaps is 1
ISAKMP: SA life type in seconds
ISAKMP: SA life duration (VPI) of 0x0 0x20 0xc4 0x9b 
ISAKMP (0): atts are acceptable.
ISAKMP (0): bad SPI size of 2 octets!
ISAKMP : Checking IPSec proposal 6

ISAKMP: transform 1, ESP_DES
ISAKMP: attributes in transform:
crypto_isakmp_process_block: src 10.66.79.229, dest 10.66.79.69
OAK_QM exchange
crypto_isakmp_process_block: src 10.66.79.229, dest 10.66.79.69
OAK_QM exchange
oakley_process_quick_mode:
OAK_QM_AUTH_AWAIT
ISAKMP (0): Creating IPSec SAs
sv2-4(config)# 
sv2-4(config)# 
sv2-4(config)# 
sv2-4(config)# 
sv2-4(config)#show uauth
Current Most Seen
Authenticated Users 1 1
Authen In Progress 0 1
ipsec user 'testuser' at 192.168.1.1, authenticated
access-list #ACSACL#-PIX-VPNClient-3d327815
sv2-4(config)#show access-list
access-list 108; 1 elements
access-list 108 permit ip 10.1.1.0 255.255.255.0 192.168.1.0 
255.255.255.0 (hitcnt=38) 
access-list #ACSACL#-PIX-VPNClient-3d327815; 1 elements
access-list #ACSACL#-PIX-VPNClient-3d327815 permit ip any host 
10.1.1.2 (hitcnt=15) 
access-list dynacl4; 1 elements
access-list dynacl4 permit ip host 10.66.79.69 
host 192.168.1.1 (hitcnt=0) 
access-list dynacl5; 1 elements
access-list dynacl5 permit ip any host 192.168.1.1 (hitcnt=15) 
sv2-4(config)#show access-list
access-list 108; 1 elements
access-list 108 permit ip 10.1.1.0 255.255.255.0 
192.168.1.0 255.255.255.0 (hitcnt=42) 
access-list #ACSACL#-PIX-VPNClient-3d327815; 1 elements
access-list #ACSACL#-PIX-VPNClient-3d327815 permit ip any 
host 10.1.1.2 (hitcnt=17) 
access-list dynacl4; 1 elements
access-list dynacl4 permit ip host 10.66.79.69 host 
192.168.1.1 (hitcnt=0) 
access-list dynacl5; 1 elements
access-list dynacl5 permit ip any host 192.168.1.1 (hitcnt=17)

 

sv2-4(config)#show crypto map

Crypto Map: "mymap" interfaces: { outside }
client configuration address respond
client authentication AuthInbound

Crypto Map "mymap" 10 ipsec-isakmp
Dynamic map template tag: dynmap

Crypto Map "mymap" 20 ipsec-isakmp
Peer = 10.66.79.229
access-list dynacl6; 1 elements
access-list dynacl6 permit ip host 10.66.79.69 
host 192.168.1.1 (hitcnt=0) 
dynamic (created from dynamic map dynmap/10)
Current peer: 10.66.79.229
Security association lifetime: 4608000 kilobytes/28800 seconds
PFS (Y/N): N
Transform sets={ myset, }

Crypto Map "mymap" 30 ipsec-isakmp
Peer = 10.66.79.229
access-list dynacl7; 1 elements
access-list dynacl7 permit ip any host 192.168.1.1 (hitcnt=0) 
dynamic (created from dynamic map dynmap/10)
Current peer: 10.66.79.229
Security association lifetime: 4608000 kilobytes/28800 seconds
PFS (Y/N): N
Transform sets={ myset, }
sv2-4(config)

Informations connexes

• Page de support PIX
• Références des commandes du pare-feu PIX
• Demandes de commentaires (RFC)
• Page d'assistance Cisco Secure ACS pour UNIX
• Cisco Secure ACS pour la page d'assistance de Windows
• Page de support TACACS/TACACS+
• TACACS+ dans la documentation d'IOS
• Page d'assistance RADIUS
• Assistance et documentation techniques - Cisco Systems