Introduction
Ce document décrit la procédure de récupération du mot de passe sur XE-SDWAN.
Problème
Pour commencer avec XE-SDWAN version 16.10.3, vous disposez d'un mot de passe administrateur unique par défaut pour des raisons de sécurité qui peuvent être facilement ignorées par l'utilisateur et potentiellement se retrouver dans une situation de verrouillage utilisateur. Ceci est particulièrement dangereux lors de la configuration initiale du routeur si la connexion de contrôle avec le contrôleur vManage n'est pas encore établie et que vous ne pouvez pas simplement joindre un nouveau modèle avec le nom d'utilisateur et le mot de passe définis. Cet article présente une procédure détaillée de récupération.
Username: admin
Password:
Router#
Sep 23 20:36:03.133: SDWAN INFO: WARNING: Please configure a new username and password; one-time user admin is removed.
Il s'agit du nouveau message que vous voyez sur la console dès la connexion avec les informations d'identification admin/admin par défaut.
Note: Cette procédure annule la configuration existante. Par conséquent, prenez une sauvegarde de la configuration si possible avant de continuer.
Solution
Voici l'exemple de la façon dont un périphérique est verrouillé car il ignore le message de mot de passe unique des journaux de console.
rommon 2 > boot bootflash:asr1000-ucmk9.16.10.3a.SPA.bin
File size is 0x2f7f66c6
Located asr1000-ucmk9.16.10.3a.SPA.bin
Image size 796878534 inode num 17, bks cnt 194551 blk size 8*512
################################################################################################################################################################################################################################################################################################################################################################################################################################
Boot image size = 796878534 (0x2f7f66c6) bytes
<<<<<<<< OUTPUT TRIMMED >>>>>>>>>
Press RETURN to get started!
<<<<<<<< OUTPUT TRIMMED >>>>>>>>>
*Sep 23 20:35:33.558: %Cisco-SDWAN-Router-SYSMGR-6-INFO-200017: R0/0: SYSMGR: Started daemon vdaemon @ pid 2218 in vpn 0
*Sep 23 20:35:33.635: %Cisco-SDWAN-Router-TTMD-6-INFO-1200001: R0/0: TTMD: Starting
*Sep 23 20:35:33.725: %Cisco-SDWAN-Router-CFGMGR-6-INFO-300001: R0/0: CFGMGR: Starting
*Sep 23 20:35:33.823: %Cisco-SDWAN-Router-FPMD-6-INFO-1100001: R0/0: FPMD: Starting
*Sep 23 20:35:33.953: %Cisco-SDWAN-Router-FTMD-6-INFO-1000020: R0/0: FTMD: SLA class '__all_tunnels__' added at index '0': loss = 128%, latency = 2147483647 ms
*Sep 23 20:35:34.424: %Cisco-SDWAN-Router-FTMD-4-WARN-1000007: R0/0: FTMD: Connection to TTM came up. p_msgq 0x7fe1b3235500 p_ftm 0x9a3020
*Sep 23 20:35:41.475: %DMI-5-INITIALIZED: R0/0: syncfd: process has initialized.
*Sep 23 20:35:44.975: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback65528, changed state to up
*Sep 23 20:35:44.991: %SYS-5-LOG_CONFIG_CHANGE: Buffer logging: level debugging, xml disabled, filtering disabled, size (262144)
*Sep 23 20:35:45.025: SDWAN INFO: Received ENABLE_CONSOLE message from sysmgr
*Sep 23 20:35:45.025: Console Enabled
*Sep 23 20:35:45.025: SDWAN INFO: PNP start, status: success
*Sep 23 20:35:45.023: %DMI-5-ACTIVE: R0/0: nesd: process is in steady state.
*Sep 23 20:35:45.888: EXEC mode enabled on console
User Access Verification
Username: admin
Password:
Router#
*Sep 23 20:36:03.133: SDWAN INFO: WARNING: Please configure a new username and password; one-time user admin is removed.
*Sep 23 20:36:03.240: %DMI-5-CONFIG_I: R0/0: nesd: Configured from NETCONF/RESTCONF by system, transaction-id 14
Router#exit
Press RETURN to get started.
User Access Verification
Username: admin
Password:
% Login invalid
Press RETURN to get started.
User Access Verification
Username:
Login incorrect
Username:
Étape 1. Lancer le processus en procédant comme suit
- Mettez le routeur hors tension et forcez-le à entrer dans le rommon avec une séquence de pause (ctrl+break, ctrl+c).
- Remplacez le registre de configuration par 0xA102 ou 0x8000.
Note: Nous vous recommandons d'utiliser 0xA102, car il est moins susceptible de fausser la frappe. Par exemple, si vous définissez par erreur le registre de configuration sur 0x800 au lieu de 0x8000 (deux zéros au lieu de trois), vous définissez le débit en bauds de la console sur 4800 au lieu du contournement de la configuration. Pour plus d'informations sur les registres de configuration, reportez-vous à l'article suivant https://www.cisco.com/c/en/us/support/docs/routers/10000-series-routers/50421-config-register-use.html
Remarque : Si vous connaissez le logiciel Cisco IOS-XE, vous vous demandez peut-être pourquoi le contournement de configuration ne peut pas être effectué avec le registre de configuration 0x2142. Cela est dû au fait que le logiciel IOS-XE SD-WAN stocke la configuration de manière différente dans la base de données de configuration (CDB) de la mémoire flash. À partir du logiciel Cisco IOS XE SD-WAN 16.10.1, le bit 15 peut être défini sur 1 pour contourner la configuration. Par conséquent, le registre de configuration doit être, par exemple, 0xA102. Cela résulte de la définition du bit 15 (0x8000) et de la combinaison avec la valeur hexadécimale du registre par défaut 0x2102.
3. Réinitialisez la case (cochez la sortie ci-dessous pour la commande).
Initializing Hardware ...
System integrity status: 90170400 12030117
U
System Bootstrap, Version 16.3(2r), RELEASE SOFTWARE
Copyright (c) 1994-2016 by cisco Systems, Inc.
Current image running: Boot ROM1
Last reset cause: PowerOn
Warning: Octeon PCIe lanes not x2 width: sts=0x5011
ASR1001-HX platform with 16777216 Kbytes of main memory
rommon 1 > confreg 0x8000
You must reset or power cycle for new config to take effect
rommon 2 > i
Resetting .......
Initializing Hardware ...
System integrity status: 90170400 12030117
Trixie configured
CaveCreek Link Status reg: Bus/Dev/Func: 0/28/1, offset 0x52, status = 00003011Times left ms:0000005C
Initializing DS31408...
Read MB FPGA Version: 0x16051716
DS31408 locked to local Oscillator
Taking Yoda out of reset...
Yoda VID enabled...
Crypto enabled...
Warning: Octeon PCIe link width not x2: sts=00001001
requesting link retrain
Astro enabled...
Astro PLL/bandgap init...
NP5c out of reset...
U
System Bootstrap, Version 16.3(2r), RELEASE SOFTWARE
Copyright (c) 1994-2016 by cisco Systems, Inc.
CPLD Version: 16033009 ASR1001-HX Slot:0
Current image running: Boot ROM1
Last reset cause: LocalSoft
Reading confreg 0x8000
Enabling interrupts
Initializing SATA controller...done
Checking for PCIe device presence...
Warning: Octeon PCIe lanes not x2 width: sts=0x5011 done
ASR1001-HX platform with 16777216 Kbytes of main memory
autoboot entry: NVRAM VALUES: bootconf: 0x0, autobootstate: 0
autobootcount: 0, autobootsptr: 0x0
Étape 2. Démarrez l'image XE-SDWAN .bin à partir de rommon.
rommon 3 > boot bootflash:asr1000-ucmk9.16.10.3a.SPA.bin
Warning: filesystem is not clean
File size is 0x2f7f66c6
Located asr1000-ucmk9.16.10.3a.SPA.bin
Image size 796878534 inode num 17, bks cnt 194551 blk size 8*512
#######################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################
File is comprised of 200 fragments (0%)
<<<<<< OUTPUT TRIMMED >>>>>>>>
Press RETURN to get started!
<<<<<< OUTPUT TRIMMED >>>>>>>>
*Sep 23 20:47:34.124: %Cisco-SDWAN-Router-SYSMGR-6-INFO-200017: R0/0: SYSMGR: Started daemon cfgmgr @ pid 5018 in vpn 0
*Sep 23 20:47:34.125: %Cisco-SDWAN-Router-SYSMGR-6-INFO-200017: R0/0: SYSMGR: Started daemon fpmd @ pid 5019 in vpn 0
*Sep 23 20:47:34.125: %Cisco-SDWAN-Router-SYSMGR-6-INFO-200017: R0/0: SYSMGR: Started daemon ftmd @ pid 5020 in vpn 0
*Sep 23 20:47:34.126: %Cisco-SDWAN-Router-SYSMGR-6-INFO-200017: R0/0: SYSMGR: Started daemon ompd @ pid 5021 in vpn 0
*Sep 23 20:47:34.127: %Cisco-SDWAN-Router-SYSMGR-6-INFO-200017: R0/0: SYSMGR: Started daemon ttmd @ pid 5022 in vpn 0
*Sep 23 20:47:34.127: %Cisco-SDWAN-Router-SYSMGR-6-INFO-200017: R0/0: SYSMGR: Started daemon vdaemon @ pid 5023 in vpn 0
*Sep 23 20:47:34.214: %Cisco-SDWAN-Router-TTMD-6-INFO-1200001: R0/0: TTMD: Starting
*Sep 23 20:47:34.307: %Cisco-SDWAN-Router-CFGMGR-6-INFO-300001: R0/0: CFGMGR: Starting
*Sep 23 20:47:34.382: %Cisco-SDWAN-Router-FPMD-6-INFO-1100001: R0/0: FPMD: Starting
*Sep 23 20:47:34.525: %Cisco-SDWAN-Router-FTMD-6-INFO-1000020: R0/0: FTMD: SLA class '__all_tunnels__' added at index '0': loss = 128%, latency = 2147483647 ms
*Sep 23 20:47:41.143: %ONEP_BASE-6-CONNECT: [Element]: ONEP session Application:com.cisco.syncfd Host:Router ID:726 User:a has connected.
*Sep 23 20:47:41.997: %DMI-5-INITIALIZED: R0/0: syncfd: process has initialized.
*Sep 23 20:47:45.480: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback65528, changed state to up
*Sep 23 20:47:45.495: %SYS-5-LOG_CONFIG_CHANGE: Buffer logging: level debugging, xml disabled, filtering disabled, size (262144)
*Sep 23 20:47:45.534: SDWAN INFO: Received ENABLE_CONSOLE message from sysmgr
*Sep 23 20:47:45.534: Console Enabled
*Sep 23 20:47:45.534: SDWAN INFO: PNP start, status: success
*Sep 23 20:47:45.531: %DMI-5-ACTIVE: R0/0: nesd: process is in steady state.
*Sep 23 20:47:45.945: EXEC mode enabled on console
Étape 3. Vous pouvez maintenant vous connecter avec les informations d'identification d'administrateur par défaut.
User Access Verification
Username: admin
Password:
Router#
*Sep 23 20:48:16.659: SDWAN INFO: WARNING: Please configure a new username and password; one-time user admin is removed.
*Sep 23 20:48:16.767: %DMI-5-CONFIG_I: R0/0: nesd: Configured from NETCONF/RESTCONF by system, transaction-id 14
Router#
Router#sh ver | i Configuration register
Configuration register is 0x8000
Étape 4. Il s'agit d'une étape obligatoire.
- Remplacez le registre de configuration par 0x2102 et réinitialisez le logiciel sdwan. Cette opération efface toute la configuration existante.
- Le routeur redémarre à cette étape et démarre avec le logiciel spécifié dans le fichier de configuration packages.conf
Router#request platform software sdwan software reset
*Sep 23 20:52:17.400: %INSTALL-5-INSTALL_START_INFO: R0/0: install_engine: Started install activate bootflash:asr1000-ucmk9.16.10.3a.SPA.bin
*Sep 23 20:52:23.919: %SYS-7-NV_BLOCK_INIT: Initialized the geometry of nvram
Router#
*Sep 23 20:52:47.943: %INSTALL-5-INSTALL_COMPLETED_INFO: R0/0: install_engine: Completed install activate PACKAGESep 23 20:53:04.302:
Initializing Hardware ...
System integrity status: 90170400 12030117
U
System Bootstrap, Version 16.3(2r), RELEASE SOFTWARE
Copyright (c) 1994-2016 by cisco Systems, Inc.
Current image running: Boot ROM1
Last reset cause: LocalSoft
Warning: Octeon PCIe lanes not x2 width: sts=0x5011
ASR1001-HX platform with 16777216 Kbytes of main memory
File size is 0x00001a47
Located packages.conf
Image size 6727 inode num 1120114, bks cnt 2 blk size 8*512
#
File size is 0x01e7df8e
Located asr1000-rpboot.16.10.3a.SPA.pkg
Image size 31973262 inode num 1120126, bks cnt 7806 blk size 8*512
########################################################################################################################################################################################################################################################################################################################
Boot image size = 31973262 (0x1e7df8e) bytes
ROM:RSA Self Test Passed
ROM:Sha512 Self Test Passed
<<<<<< OUTPUT TRIMMED >>>>>>>>
*Sep 23 20:57:13.347: %ONEP_BASE-6-CONNECT: [Element]: ONEP session Application:com.cisco.syncfd Host:Router ID:8029 User:a has connected.
*Sep 23 20:57:15.226: %Cisco-SDWAN-Router-SYSMGR-6-INFO-200017: R0/0: SYSMGR: Started daemon cfgmgr @ pid 4435 in vpn 0
*Sep 23 20:57:15.227: %Cisco-SDWAN-Router-SYSMGR-6-INFO-200017: R0/0: SYSMGR: Started daemon fpmd @ pid 4436 in vpn 0
*Sep 23 20:57:15.228: %Cisco-SDWAN-Router-SYSMGR-6-INFO-200017: R0/0: SYSMGR: Started daemon ftmd @ pid 4437 in vpn 0
*Sep 23 20:57:15.229: %Cisco-SDWAN-Router-SYSMGR-6-INFO-200017: R0/0: SYSMGR: Started daemon ompd @ pid 4438 in vpn 0
*Sep 23 20:57:15.229: %Cisco-SDWAN-Router-SYSMGR-6-INFO-200017: R0/0: SYSMGR: Started daemon ttmd @ pid 4439 in vpn 0
*Sep 23 20:57:15.230: %Cisco-SDWAN-Router-SYSMGR-6-INFO-200017: R0/0: SYSMGR: Started daemon vdaemon @ pid 4440 in vpn 0
*Sep 23 20:57:15.308: %Cisco-SDWAN-Router-TTMD-6-INFO-1200001: R0/0: TTMD: Starting
*Sep 23 20:57:15.391: %Cisco-SDWAN-Router-CFGMGR-6-INFO-300001: R0/0: CFGMGR: Starting
*Sep 23 20:57:15.484: %Cisco-SDWAN-Router-FPMD-6-INFO-1100001: R0/0: FPMD: Starting
*Sep 23 20:57:15.620: %Cisco-SDWAN-Router-FTMD-6-INFO-1000020: R0/0: FTMD: SLA class '__all_tunnels__' added at index '0': loss = 128%, latency = 2147483647 ms
*Sep 23 20:57:16.092: %Cisco-SDWAN-Router-FTMD-4-WARN-1000007: R0/0: FTMD: Connection to TTM came up. p_msgq 0x7f5815c35500 p_ftm 0x9a3020
*Sep 23 20:57:27.380: %DMI-5-INITIALIZED: R0/0: syncfd: process has initialized.
*Sep 23 20:57:35.032: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback65528, changed state to up
*Sep 23 20:57:35.048: %SYS-5-LOG_CONFIG_CHANGE: Buffer logging: level debugging, xml disabled, filtering disabled, size (262144)
*Sep 23 20:57:35.081: SDWAN INFO: Received ENABLE_CONSOLE message from sysmgr
*Sep 23 20:57:35.081: Console Enabled
*Sep 23 20:57:35.081: SDWAN INFO: PNP start, status: success
*Sep 23 20:57:35.079: %DMI-5-ACTIVE: R0/0: nesd: process is in steady state.
*Sep 23 20:57:35.682: EXEC mode enabled on console
Étape 5. Maintenant, une fois de plus, vous êtes invité à fournir des informations d'identification d'administrateur uniques. Après cette étape, n'oubliez pas de modifier le mot de passe par défaut. Il est également recommandé d'ajouter un utilisateur supplémentaire. Si vous manquez cette étape et que vous êtes verrouillé, vous devez répéter toutes les étapes à nouveau.
User Access Verification
Username: admin
Password:
Router#
*Sep 23 20:58:18.048: SDWAN INFO: WARNING: Please configure a new username and password; one-time user admin is removed.
*Sep 23 20:58:18.155: %DMI-5-CONFIG_I: R0/0: nesd: Configured from NETCONF/RESTCONF by system, transaction-id 18
Router#confi
Router#config-tr
System is still initializing. Wait for PnP to be completed or terminate PnP with the following command:
pnpa service discovery stop
Router#pnpa service discovery stop
PNP-EXEC-DISCOVERY (1): Stopping PnP Discovery...
Waiting for PnP discovery cleanup ..
Router#
*Sep 23 20:58:48.997: %PNP-6-PNP_DISCOVERY_ABORT_ON_CLI: PnP Discovery abort on CLI input
*Sep 23 20:58:48.999: %DMI-5-SYNC_START: R0/0: syncfd: External change to running configuration detected. The running configuration will be synchronized to the NETCONF running data store.
*Sep 23 20:58:54.955: %DMI-5-SYNC_COMPLETE: R0/0: syncfd: The running configuration has been synchronized to the NETCONF running data store.
*Sep 23 20:58:54.955: %DMI-5-ACTIVE: R0/0: syncfd: process is in steady state.
*Sep 23 20:58:55.150: %DMI-5-CONFIG_I: R0/0: nesd: Configured from NETCONF/RESTCONF by system, transaction-id 181
*Sep 23 20:58:55.676: %Cisco-SDWAN-Router-SYSMGR-5-NTCE-200050: R0/0: SYSMGR: System status solid green (reason: All daemons up)
Router#
*Sep 23 20:59:00.083: %INSTALL-5-INSTALL_START_INFO: R0/0: install_engine: Started install commit PACKAGE
*Sep 23 20:59:00.327: %INSTALL-5-INSTALL_COMPLETED_INFO: R0/0: install_engine: Completed install commit PACKAGE
Router#sh ver | i register
Configuration register is 0x2102
Router#sh sdwan ver
*Sep 23 20:59:12.640: %PNP-6-PNP_DISCOVERY_ABORT_ON_CLI: PnP Discovery abort on CLI input
*Sep 23 20:59:12.640: %PNP-6-PNP_DISCOVERY_STOPPED: PnP Discovery stopped (Discovery Aborted)16.10.3a
Router#
Router#sh sdwan ver
16.10.3a
Router#
Router#conf
Router#config-tr
admin connected from 127.0.0.1 using console on Router
Router(config)# username admin privilege 15 secret <your password>
Router(config)# username sdwan privilege 15 secret <your password>
Router(config)# comm
Commit complete.
Router(config)#
*Sep 23 21:00:59.270: %DMI-5-CONFIG_I: R0/0: nesd: Configured from NETCONF/RESTCONF by admin, transaction-id 204
Router(config)# end
Étape 6. Vérifiez que vous avez toujours accès au périphérique avec le nom d'utilisateur et le mot de passe nouvellement créés.
Router#exit
Router con0 is now available
Press RETURN to get started.
User Access Verification
Username: admin
Password:
Router>en
Router#
Router#exit
Router con0 is now available
Press RETURN to get started.
User Access Verification
Username: sdwan
Password:
Router>en
Router#