Este documento describe los pasos para instalar y para preparar los Servicios inalámbricos en el regulador del Wireless LAN 5760 (WLC) y el 3850 Switch. Esta configuración inicial de los documentos abarca y el punto de acceso se unen al proceso para ambas Plataformas.
No hay requisitos específicos para este documento.
La información que contiene este documento se basa en las siguientes versiones de software y hardware.
La información que contiene este documento se creó a partir de los dispositivos en un ambiente de laboratorio específico. Todos los dispositivos que se utilizan en este documento se pusieron en funcionamiento con una configuración verificada (predeterminada). Si la red está funcionando, asegúrese de haber comprendido el impacto que puede tener cualquier comando.
El WLC CT5760 es el regulador basado en software del primer ® del Cisco IOS XE construido con ASIC elegante previsto para ser desplegado como regulador centralizado en la arquitectura inalámbrica unificada última generación. La plataforma también soporta las nuevas funciones de la movilidad con los 3850 Series Switch convergidos del acceso.
Los reguladores CT5760 se despliegan típicamente cerca de la base. Los puertos de link ascendente conectados con el switch del núcleo se pueden configurar como puertos de tronco EtherChannel para asegurar la redundancia del puerto. Este nuevo regulador es un regulador inalámbrico extensible y del rendimiento alto, que puede escalar hasta 1000 AP y a 12,000 clientes. El regulador tiene seis puertos de los datos del 10 Gbps por una capacidad total de 60 Gbps.
Las 5760 Series trabajan conjuntamente con el Cisco Aironet AP, la infraestructura primera de Cisco, y el motor de los Servicios de movilidad de Cisco para soportar los datos de red inalámbrica del negocio crítico, la Voz, el vídeo, y las aplicaciones de servicios de ubicación.
Las Cisco Catalyst 3850 Series son la última generación de switches de capa de acceso apilables de la empresa-clase que proporcionen la convergencia completa entre atado con alambre y Tecnología inalámbrica en una plataforma única. Accionado por el software IOS-XE, soportan al servicio de red inalámbrica con el control y el aprovisionamiento del protocolo de los untos de acceso de red inalámbrica (CAPWAP). El nuevo avión unificado de los datos del acceso de Cisco (UADP) ASIC acciona el Switch y los permisos uniforman la aplicación de políticas de la atar con alambre-Tecnología inalámbrica, la visibilidad de la aplicación, la flexibilidad, y la optimización de la aplicación. Esta convergencia se emplea la resistencia de Cisco nuevo y mejorado StackWise-480. El poder completo de IEEE 802.3at del soporte de los Cisco Catalyst 3850 Series Switch sobre los Ethernetes más (PoE+), módulos de red modulares y reemplazables en el terreno, fans redundantes, y fuentes de alimentación.
Esta sección delinea los pasos para configurar con éxito los 5760 WLC para recibir los Servicios inalámbricos.
--- System Configuration Dialog ---
Enable secret warning
----------------------------------
In order to access the device manager, an enable secret is required
If you enter the initial configuration dialog, you will be prompted for the
enable secret
If you choose not to enter the intial configuration dialog, or if you exit setup
without setting the enable secret,
please set an enable secret using the following CLI in configuration mode-
enable secret 0 <cleartext password>
----------------------------------
Would you like to enter the initial configuration dialog? [yes/no]: yes
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Basic management setup configures only enough connectivity
for management of the system, extended setup will ask you
to configure each interface on the system
Would you like to enter basic management setup? [yes/no]: yes
Configuring global parameters:
Enter host name [Controller]: w-5760-1
The enable secret is a password used to protect access to
privileged EXEC and configuration modes. This password, after
entered, becomes encrypted in the configuration.
Enter enable secret: cisco
The enable password is used when you do not specify an
enable secret password, with some older software versions, and
some boot images.
Enter enable password: cisco
The virtual terminal password is used to protect
access to the router over a network interface.
Enter virtual terminal password: cisco
Configure a NTP server now? [yes]:
Enter ntp server address : 192.168.1.200
Enter a polling interval between 16 and 131072 secs which is power of 2:16
Do you want to configure wireless network? [no]: no
Setup account for accessing HTTP server? [yes]: yes
Username [admin]: admin
Password [cisco]: cisco
Password is UNENCRYPTED.
Configure SNMP Network Management? [no]: no
Current interface summary
Any interface listed with OK? value "NO" does not have a valid configuration
Interface IP-Address OK? Method Status Protocol
Vlan1 unassigned NO unset up up
GigabitEthernet0/0 unassigned YES unset up up
Te1/0/1 unassigned YES unset up up
Te1/0/2 unassigned YES unset down down
Te1/0/3 unassigned YES unset down down
Te1/0/4 unassigned YES unset down down
Te1/0/5 unassigned YES unset down down
Te1/0/6 unassigned YES unset down down
Enter interface name used to connect to the
management network from the above interface summary: vlan1
Configuring interface Vlan1:
Configure IP on this interface? [yes]: yes
IP address for this interface: 192.168.1.20
Subnet mask for this interface [255.255.255.0] : 255.255.255.0
Class C network is 192.168.1.0, 24 subnet bits; mask is /24
Wireless management interface needs to be configured at startup
It needs to be mapped to an SVI that's not Vlan 1 (default)
Enter VLAN No for wireless management interface: 120
Enter IP address :192.168.120.94
Enter IP address mask: 255.255.255.0
El script siguiente del comando configuration fue creado:
w-5760-1
enable secret 4 tnhtc92DXBhelxjYk8LWJrPV36S2i4ntXrpb4RFmfqY^Q
enable password cisco
line vty 0 15
password cisco
ntp server 192.168.1.200 maxpoll 4 minpoll 4
username admin privilege 15 password cisco
no snmp-server
!
no ip routing
!
interface Vlan1
no shutdown
ip address 192.168.1.20 255.255.255.0
!
interface GigabitEthernet0/0
shutdown
no ip address
!
interface TenGigabitEthernet1/0/1
!
interface TenGigabitEthernet1/0/2
!
interface TenGigabitEthernet1/0/3
!
interface TenGigabitEthernet1/0/4
!
interface TenGigabitEthernet1/0/5
!
interface TenGigabitEthernet1/0/6
vlan 120
interface vlan 120
ip addr 192.168.120.94 255.255.255.0
exit
wireless management interface Vlan120
!
end
[0] Go to the IOS command prompt without saving this config.
[1] Return back to the setup without saving this config.
[2] Save this configuration to nvram and exit.
Enter your selection [2]: 2
Building configuration...
Compressed configuration from 2729 bytes to 1613 bytes[OK]
Use the enabled mode 'configure' command to modify this configuration.
Press RETURN to get started!
Configure la interfaz de TenGig conectada con la red de estructura básica en donde los flujos de tráfico CAPWAP entrantes/salientes. En este ejemplo, la interfaz usada es TenGigabitEthernet1/0/1. Se permiten el VLAN1 y el VLA N 120.
interface TenGigabitEthernet1/0/1
switchport trunk allowed vlan 1,120
switchport mode trunk
ip dhcp relay information trusted
ip dhcp snooping trust
Configure la ruta predeterminado saliente:
ip route 0.0.0.0 0.0.0.0 192.168.1.1
El GUI se puede acceder vía los <ipaddress >/wireless de https://
Los credenciales de inicio de sesión se definen ya en el diálogo de configuración inicial.
username admin privilege 15 password cisco
wireless management interface Vlan120
w-5760-1#sh run int vlan 120
Building configuration...
Current configuration : 62 bytes
!
interface Vlan120
ip address 192.168.120.94 255.255.255.0
end
w-5760-1#sh ip int br
Interface IP-Address OK? Method Status Protocol
Vlan1 192.168.1.20 YES manual up up
Vlan120 192.168.120.94 YES manual up up
GigabitEthernet0/0 unassigned YES unset down down
Te1/0/1 unassigned YES unset up up
Te1/0/2 unassigned YES unset down down
Te1/0/3 unassigned YES unset down down
Te1/0/4 unassigned YES unset down down
Te1/0/5 unassigned YES unset down down
Te1/0/6 unassigned YES unset down down
Capwap2 unassigned YES unset up up
w-5760-1#
w-5760-1#license right-to-use activate apcount <count> slot 1 acceptEULA
w-5760-1#show wireless country configured
Configured Country.............................: US - United States
Configured Country Codes
US - United States : 802.11a Indoor,Outdoor/ 802.11b / 802.11g
Para modificar el código del país, ingrese estos comandos:
w-5760-1(config)#ap dot11 24ghz shutdown
w-5760-1(config)#ap dot11 5ghz shutdown
w-5760-1(config)#ap country BE
Changing country code could reset channel and RRM grouping configuration.
If running in RRM One-Time mode, reassign channels after this command.
Check customized APs for valid channel values after this command.
Are you sure you want to continue? (y/n)[y]: y
w-5760-1(config)#no ap dot11 24ghz shut
w-5760-1(config)#no ap dot11 5ghz shut
w-5760-1(config)#end
w-5760-1#wr
Building configuration...
Compressed configuration from 3564 bytes to 2064 bytes[OK]
w-5760-1#show wireless country configured
Configured Country.............................: BE - Belgium
Configured Country Codes
BE - Belgium : 802.11a Indoor,Outdoor/ 802.11b / 802.11g
Para asegurarse de que los AP se hayan unido a, ingrese el comando show ap summary:
w-5760-1#show ap summary
Number of APs: 1
Global AP User Name: Not configured
Global AP Dot1x User Name: Not configured
AP Name AP Model Ethernet MAC Radio MAC State
--------------------------------------------------------------------------
APa493.4cf3.232a 1042N a493.4cf3.232a 10bd.186d.9a40 Registered
Los debugs útiles para resolver problemas el AP se unen a los problemas:
w-5760-1#debug capwap ap events
capwap/ap/events debugging is on
w-5760-1#debug capwap ap error
capwap/ap/error debugging is on
w-5760-1#debug dtls ap event
dtls/ap/event debugging is on
w-5760-1#debug capwap ios event
CAPWAP Event debugging is on
5760-1#debug capwap ios error
CAPWAP Error debugging is on
Esta sección incluye la configuración requerida recibir los Servicios inalámbricos en los 3850.
--- System Configuration Dialog ---
Enable secret warning
----------------------------------
In order to access the device manager, an enable secret is required
If you enter the initial configuration dialog, you will be prompted
for the enable secret
If you choose not to enter the intial configuration dialog, or if you
exit setup without setting the enable secret,
please set an enable secret using the following CLI in configuration mode-
enable secret 0 <cleartext password>
----------------------------------
Would you like to enter the initial configuration dialog? [yes/no]: yes
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Basic management setup configures only enough connectivity
for management of the system, extended setup will ask you
to configure each interface on the system
Would you like to enter basic management setup? [yes/no]: yes
Configuring global parameters:
Enter host name [Switch]: sw-3850-1
The enable secret is a password used to protect access to
privileged EXEC and configuration modes. This password, after
entered, becomes encrypted in the configuration.
Enter enable secret: Cisco123
The enable password is used when you do not specify an
enable secret password, with some older software versions, and
some boot images.
Enter enable password: Cisco123
The virtual terminal password is used to protect
access to the router over a network interface.
Enter virtual terminal password: Cisco123
Do you want to configure country code? [no]: yes
Enter the country code[US]:US
Note : Enter the country code in which you are installing this 3850 Switch and
the AP(s). If your country code is not recognized, enter one that is compliant
with the regulatory domain of your own country
Setup account for accessing HTTP server? [yes]: yes
Username [admin]: admin
Password [cisco]: cisco
Password is UNENCRYPTED.
Configure SNMP Network Management? [no]: no
Current interface summary
Any interface listed with OK? value "NO" does not have a valid configuration
Interface IP-Address OK? Method Status Protocol
Vlan1 unassigned NO unset up down
GigabitEthernet0/0 unassigned YES unset up up
GigabitEthernet2/0/1 unassigned YES unset down down
GigabitEthernet2/0/2 unassigned YES unset down down
GigabitEthernet2/0/3 unassigned YES unset down down
...
...
...
GigabitEthernet2/0/46 unassigned YES unset down down
GigabitEthernet2/0/47 unassigned YES unset down down
GigabitEthernet2/0/48 unassigned YES unset up up
GigabitEthernet2/1/1 unassigned YES unset down down
GigabitEthernet2/1/2 unassigned YES unset down down
GigabitEthernet2/1/3 unassigned YES unset down down
GigabitEthernet2/1/4 unassigned YES unset down down
Te2/1/1 unassigned YES unset down down
Te2/1/2 unassigned YES unset down down
Te2/1/3 unassigned YES unset down down
Te2/1/4 unassigned YES unset down down
Enter interface name used to connect to the
management network from the above interface summary: vlan1
Configuring interface Vlan1:
Configure IP on this interface? [yes]: yes
IP address for this interface: 192.168.1.2
Subnet mask for this interface [255.255.255.0] : 255.255.255.0
Class C network is 192.168.1.0, 24 subnet bits; mask is /24
Este script del comando configuration fue creado:
hostname sw-3850-1
enable secret 4 vwcGVdcUZcRMCyxaH2U9Y/PTujsnQWPSbt.LFG8lhTw
enable password Cisco123
line vty 0 15
password Cisco123
ap dot11 24ghz shutdown
ap dot11 5ghz shutdown
ap country US
no ap dot11 24ghz shutdown
no ap dot11 5ghz shutdown
username admin privilege 15 password 0 cisco
no snmp-server
!
no ip routing
!
interface Vlan1
no shutdown
ip address 192.168.1.2 255.255.255.0
!
interface GigabitEthernet0/0
shutdown
no ip address
!
interface GigabitEthernet2/0/1
!
interface GigabitEthernet2/0/2
!
interface GigabitEthernet2/0/3
...
...
...
interface GigabitEthernet2/0/46
!
interface GigabitEthernet2/0/47
!
interface GigabitEthernet2/0/48
!
interface GigabitEthernet2/1/1
!
interface GigabitEthernet2/1/2
!
interface GigabitEthernet2/1/3
!
interface GigabitEthernet2/1/4
!
interface TenGigabitEthernet2/1/1
!
interface TenGigabitEthernet2/1/2
!
interface TenGigabitEthernet2/1/3
!
interface TenGigabitEthernet2/1/4
!
end
[0] Go to the IOS command prompt without saving this config.
[1] Return back to the setup without saving this config.
[2] Save this configuration to nvram and exit.
Enter your selection [2]: 2
The enable password you have chosen is the same as your enable secret.
This is not recommended. Re-enter the enable password.
Changing country code could reset channel and RRM grouping configuration.
If running in RRM One-Time mode, reassign channels after this command.
Check customized APs for valid channel values after this command.
Are you sure you want to continue? (y/n)[y]: y
% Generating 1024 bit RSA keys, keys will be non-exportable...
[OK] (elapsed time was 1 seconds)
Building configuration...
Compressed configuration from 4414 bytes to 2038 bytes[OK]
Use the enabled mode 'configure' command to modify this configuration.
Press RETURN to get started!
Para habilitar los Servicios inalámbricos, los 3850 deben ejecutar los ipservices o la licencia del ipbase.
sw-3850-1(config)#wireless management interface vlan <1-4095>
Un MC se debe definir para permitir que los AP se unan a.
Si estos 3850 son el MC, ingrese el comando controller sin hilos de la movilidad:
sw-3850-1(config)#wireless mobility controller
sw-3850-1(config)#wireless mobility controller ip a.b.c.d
Y en el MC, ingrese estos comandos:
3850MC(config)#wireless mobility controller peer-group <SPG1>
3850MC(config)#wireless mobility controller peer-group <SPG1> member
ip w.x.y.z
Asegúrese de que las licencias activas AP estén disponibles en el MC (el MA utiliza las licencias que se activan en el MC):
sw-3850-1#show license right-to-use summary
License Name Type Count Period left
-----------------------------------------------
ipservices permanent N/A Lifetime
apcount base 1 Lifetime
apcount adder 49 Lifetime
-----------------------------------------------
License Level In Use: ipservices
License Level on Reboot: ipservices
Evaluation AP-Count: Disabled
Total AP Count Licenses: 50
AP Count Licenses In-use: 1
AP Count Licenses Remaining: 49
Para activar la licencia de la cuenta AP en los 3850, ingrese este comando con la cuenta requerida AP en el MC:
sw-3850-1#license right-to-use activate apcount <count> slot <#> acceptEULA
Configure el proceso de detección AP.
Para que los AP se unan al regulador, la configuración de puerto de switch se debe fijar como puerto de acceso en la Administración inalámbrica vlan:
Si el VLAN 100 se utiliza para la interfaz de administración inalámbrica:
sw-3850-1(config)#interface gigabit1/0/10
sw-3850-1(config-if)#switchport mode access
sw-3850-1(config-if)#switchport access vlan 100
Acceso Web de la configuración.
El GUI se puede acceder vía https:// <ipaddress>/wireless
Los credenciales de inicio de sesión se definen ya en el diálogo de configuración inicial.
username admin privilege 15 password 0 cisco ( username for Web access)
sw-3850-1#show wireless country configured
Configured Country.............................: US - United States
Configured Country Codes
US - United States : 802.11a Indoor,Outdoor/ 802.11b / 802.11g
Para modificar el código del país, ingrese estos comandos:
sw-3850-1(config)#ap dot11 24ghz shutdown
sw-3850-1(config)#ap dot11 5ghz shutdown
sw-3850-1(config)#ap country BE
Changing country code could reset channel and RRM grouping configuration.
If running in RRM One-Time mode, reassign channels after this command.
Check customized APs for valid channel values after this command.
Are you sure you want to continue? (y/n)[y]: y
sw-3850-1(config)#no ap dot11 24ghz shut
sw-3850-1(config)#no ap dot11 5ghz shut
sw-3850-1(config)#end
sw-3850-1#wr
Building configuration...
Compressed configuration from 3564 bytes to 2064 bytes[OK]
sw-3850-1#show wireless country configured
Configured Country.............................: BE - Belgium
Configured Country Codes
BE - Belgium : 802.11a Indoor,Outdoor/ 802.11b / 802.11g
Para asegurarse de que el AP se haya unido a, ingrese el comando show ap summary:
sw-3850-1#show ap summary
Number of APs: 1
Global AP User Name: Not configured
Global AP Dot1x User Name: Not configured
AP Name AP Model Ethernet MAC Radio MAC State
------------------------------------------------------------------------------
APa493.4cf3.232a 1042N a493.4cf3.231a 10bd.186e.9a40 Registered
Los debugs útiles para resolver problemas el AP se unen a los problemas:
sw-3850-1#debug capwap ap events
capwap/ap/events debugging is on
sw-3850-1#debug capwap ap error
capwap/ap/error debugging is on
sw-3850-1#debug dtls ap event
dtls/ap/event debugging is on
sw-3850-1#debug capwap ios event
CAPWAP Event debugging is on
sw-3850-1#debug capwap ios error
CAPWAP Error debugging is on