La extensión que permite que BGP transporte la información de IP de Capa 2 MAC y Capa 3 es EVPN y utiliza Multi-Protocol Border Gateway Protocol (MP-BGP) como protocolo para distribuir la información de alcance que pertenece a la red superpuesta VXLAN.
Resolución de problemas de EVPN VxLAN TRM en switches Catalyst 9000
Contenido
Introducción
Este documento describe cómo resolver problemas con TRM (Tenant Routed Multicast) over EVPN VxLAN.
Prerequisites
- Se recomienda que esté familiarizado con la función VxLAN de EVPN unidifusión, BGP y MVPN (red privada virtual multidifusión).
- Además, debe comprender cómo funciona la multidifusión y los conceptos de multidifusión
Requirements
Esta guía asume que los peers BGP y NVE ya son correctos. Si hay problemas con la activación básica de VxLAN de EVPN (falla de ping unidifusión, BGP, pares NVE desactivados, etc.), consulte las guías de resolución de problemas de BGP, EVPN, ruta/switch según sea necesario.
Disponibilidad de funciones en cada versión de código
| Versión | Función |
| 17.1.1 | TRMv4 con RP de difusión ilimitada |
| 17.3.1 | TRMv4 con RP externo o RP único |
| 17.3.1 |
TRMv6 con RP de difusión ilimitada |
| 17.3.1 |
TRMv6 con RP externo o RP único |
| 17.3.1 | TRMv4 con interconexión MVPN (perfil 11) con RP único en el lado del fabric |
| 17.6.2 y 17.7.1 | Mdt de datos TRMv4 con RP de difusión ilimitada, RP externo o RP único |
Componentes Utilizados
La información que contiene este documento se basa en las siguientes versiones de software y hardware.
- C9300
- C9400
- C9500
- C9600
La información que contiene este documento se creó a partir de los dispositivos en un ambiente de laboratorio específico. Todos los dispositivos que se utilizan en este documento se pusieron en funcionamiento con una configuración verificada (predeterminada). Si tiene una red en vivo, asegúrese de entender el posible impacto de cualquier comando.
Antecedentes
Para configurar EVPN TRM, consulte: Guía de Configuración de BGP EVPN VXLAN, Cisco IOS XE Amsterdam 17.3.x
La multidifusión enrutada de arrendatarios (TRM) es una solución basada en BGP-EVPN que permite el enrutamiento de multidifusión entre orígenes y receptores conectados en VTEPS en el fabric VxLAN [RFC7432]. TRM se basa en las rutas presentes en la EVPN de unidifusión para detectar el origen de multidifusión y el RP de multidifusión. Al igual que con NG-MVPN, la información de origen y receptor de multidifusión se propaga mediante el protocolo BGP entre los VTEP configurados con la familia de direcciones BGP MVPN. No se envían paquetes PIM/IGMP a la estructura VxLAN desde un TRM VTEP.
El problema clave que soluciona TRM es la capacidad de los remitentes y receptores de multidifusión que se encuentran en diferentes VLAN pero en el mismo VRF, para poder comunicarse entre sí. Sin TRM, el tráfico multidifusión se envía como parte de la misma infraestructura BUM (difusión, unidifusión y multidifusión) en la capa subyacente, que puede ser un árbol de multidifusión o una replicación de entrada. Esta infraestructura se crea por VLAN y, como resultado, mientras que los orígenes y receptores de multidifusión en la misma VLAN pueden comunicarse, los que se encuentran en VLAN diferentes no pueden. Con TRM, la multidifusión se saca de BUM y se agrupa bajo el VRF principal. Debido a esto, la comunicación multicast está completamente habilitada, independientemente de las VLAN en las que reside el origen o el receptor.
TRM proporciona reenvío multidifusión con detección de varios arrendatarios entre remitentes y receptores dentro de la misma o diferentes subredes locales o a través de VTEP. Véase la guía Guía de Configuración de BGP EVPN VXLAN, Cisco IOS XE Amsterdam 17.3.x para ver más detalles
Cómo orientarse en esta guía:
- La guía se divide en 4 escenarios en función de la ubicación del RP.
- Un escenario puede hacer referencia a ejemplos de CLI no directamente en la sección en la que se encuentra. Por ejemplo, el Escenario 2 de SSM hace referencia al Escenario 1 para comprender cómo leer ciertas CLI.
- Solo el escenario 1 abarca IPv4 e IPv6, ya que los conceptos son fundamentalmente los mismos para ambas familias de direcciones.
- Los requisitos enumerados en estos escenarios asumen que el origen y el receptor están conectados directamente a los VTEPs (consulte la sección de información relacionada "Orígenes y receptores fuera del fabric" para obtener más información sobre esto).
| Escenarios |
IPv4/v6 |
¿Qué se incluye en cada |
| Detalles comunes para todos los demás escenarios |
IPv4 |
Siempre requerido: la base de MVPN y NVE están en buen estado, la verificación RPF a cualquier fuente TRM es el L3VNI. |
| RP AnyCast (cada VTEP es un RP con una IP RP común) |
IPv4/v6 |
Comandos BGP, PIM, IGMP, MFIB y FED con todos los detalles para ambos ejemplos de captura de IPv4/v6 plus |
| Sin RP (superposición SSM) |
IPv4 |
SSM Información específica. (Consulte la situación 1 para obtener información común) |
| RP dentro del fabric (un RP común para el fabric) |
IPv4 |
Comandos BGP, PIM, IGMP, MFIB y FED con todos los detalles para IPv4 |
| RP fuera del fabric (el RP no está en el fabric) |
IPv4 |
Información específica del borde de IP a fabric. (Consulte la situación 3 para obtener información común) |
| RP dentro del fabric (un RP común para el fabric) con L2VNI simétrico |
IPv4 |
Advertencias para el uso de un único RP en el fabric cuando el VNI está en VTEP tanto del emisor como del receptor. (Consulte la situación 3 para obtener información común) |
En este documento de troubleshooting, se han agregado comentarios al final de ciertas líneas de los resultados de los comandos show. Esto se ha hecho para resaltar o explicar un aspecto específico de esa línea de salida. Si un comentario comienza en una nueva línea, se refiere a la línea de salida que precede al comentario. Esta notación se ha utilizado en todo el documento para resaltar los comentarios dentro de los resultados de los comandos show:
<-— Text highlighted in this format inside a command's output represents a comment.
This is done for explanation purpose only and is not part of the command's output.
Terminology
| EVPN |
Red privada virtual Ethernet |
|
| VXLAN |
LAN extensible virtual (red de área local) |
VXLAN está diseñado para superar las limitaciones inherentes de las VLAN y el STP. Se propone un estándar IETF [RFC 7348] para proporcionar los mismos servicios de red Ethernet de capa 2 que las VLAN, pero con mayor flexibilidad. Funcionalmente, es un protocolo de encapsulación MAC-in-UDP que se ejecuta como una superposición virtual en una red subyacente de Capa 3. |
| VTEP |
Terminal de túnel virtual |
Este es el dispositivo que realiza la encapsulación y desencapsulación |
| NVE |
Interfaz virtual de red |
Interfaz lógica donde se produce la encapsulación y la desencapsulación |
| VNI |
identificador de red VXLAN |
Identifica de forma exclusiva cada subred o segmento de capa 2. Existen dos tipos de VNI: Simétrico (L2VNI): los VTEP tienen el mismo VNI Asimétrico (L3VNI): Los VTEP no tienen el mismo VNI y se enrutan a través de un único VNI común. |
| MDT |
Árbol de distribución de multidifusión |
El árbol de multidifusión creado entre VTEP para la encapsulación y la tunelización del tráfico de multidifusión de arrendatarios. |
| VAGABUNDO |
Difusión, unidifusión desconocida, multidifusión |
El tráfico BUM se envía a través del grupo Mcast vinculado al VNI en la configuración NVE. |
| RP |
Punto de encuentro |
Función que desempeña un dispositivo en el modo disperso de PIM. El punto de encuentro común para fuentes y receptores de multidifusión. |
| AnyCast (RP) |
Punto de encuentro AnyCast |
Dos o más RP se configuran con la misma dirección IP en las interfaces de loopback. FHR se registra en el RP más cercano en función del routing unidifusión. |
| RPT (árbol) |
Árbol de ruta raíz |
También se denomina árbol Shared o *,G. Esta trayectoria se dirige hacia el RP |
| SPT (árbol) |
Árbol de trayecto más corto |
La ruta más corta al origen determinada por la tabla de routing unidifusión |
| FHR |
Router de primer salto |
El dispositivo que está conectado directamente (ARP adyacente) al origen. El FHR registra la información de origen con el RP. |
| LHR |
Router de último salto |
El dispositivo al que está conectado el receptor |
| RPF |
Reenvío de Trayectoria Inversa |
Ruta de acceso unidifusión de vuelta al origen. Los paquetes de multidifusión entrantes no se aceptan/reenvían a menos que se reciban en la misma ruta que la tabla de ruteo de unidifusión. ('ip multicast multipath', casos de uso excluidos). |
| MRIB |
Base de Información de Ruteo Multicast |
La tabla de ruteo de multidifusión de software, también llamada tabla de ruta multicast |
| MFIB |
Base de Información de Reenvío Multicast |
El equivalente multidifusión de CEF. Se rellena con actualizaciones de MRIB y se utiliza para reenviar en el plano de datos. |
| FED |
Controlador de motor de reenvío |
Componente que programa el hardware del dispositivo. |
| IIF |
Interfaz entrante |
Interfaz habilitada para PIM que es también la ruta ascendente RPF unidifusión de regreso al Origen. (visto en show ip mroute) |
| OIF |
Interfaz saliente |
Interfaz habilitada para PIM que es de flujo descendente hacia el receptor. (visto en show ip mroute) |
Verificación
Verificación común a todos los escenarios
En esta primera sección se tratan los requisitos básicos necesarios para cualquiera de los escenarios.
- Asegúrese de que los pares NVE requeridos estén activos
- Asegúrese de que la interfaz RPF hacia el Origen en el VRF de Arrendatario sea el L3VNI SVI. Si la interfaz RPF no es el L3VNI SVI, BGP no envía una ruta de unión de tipo 7. En cualquier escenario, la interfaz RPF debe apuntar a esta interfaz.
- Asegúrese de que la ruta subyacente (túnel MDT) entre pares esté completa.
- Asegúrese de que BGP se utilice para el plano de control de multidifusión (utilice MVPN frente a PIM)
Verificar iguales NVE
Asegúrese de que los pares NVE estén activos entre VTEP para cualquiera de los escenarios de esta guía
- Los peers NVE están formados por direcciones aprendidas de BGP.
Leaf-01#sh nve peers
Interface VNI Type Peer-IP RMAC/Num_RTs eVNI state flags UP time
nve1 50901 L3CP 172.16.254.4 7c21.0dbd.9548 50901 UP A/-/4 01:54:11 <-- IPv4 peering with Leaf 02
nve1 50901 L3CP 172.16.254.4 7c21.0dbd.9548 50901 UP A/M/6 17:48:36 <-- IPv6 peering with Leaf 02
Leaf-02#sh nve peers
Interface VNI Type Peer-IP RMAC/Num_RTs eVNI state flags UP time
nve1 50901 L3CP 172.16.254.3 10b3.d56a.8fc8 50901 UP A/-/4 01:55:44 <-- IPv4 peering with Leaf 01
nve1 50901 L3CP 172.16.254.3 10b3.d56a.8fc8 50901 UP A/M/6 17:56:19 <-- IPv6 peering with Leaf 01
Verificar la Interfaz RPF en el VRF de Arrendatario
Si esta interfaz es cualquier interfaz que no sea L3VNI SVI, BGP no origina una unión MVPN de tipo 7.
- Si no ve esta interfaz, confirme que no hay ningún problema con la configuración que haría que la ruta de regreso a la fuente fuera una interfaz que no fuera L3VNI.
Leaf-03#sh ip rpf vrf green 10.1.101.11 <-- Multicast source IP
RPF information for ? (10.1.101.11)
RPF interface: Vlan901 <-- RPF interface is the L3VNI SVI
RPF neighbor: ? (172.16.254.3) <-- Underlay Next hop IP
RPF route/mask: 10.1.101.0/24 <-- Network prefix for the Source
RPF type: unicast (bgp 65001)
Doing distance-preferred lookups across tables
RPF topology: ipv4 multicast base, originated from ipv4 unicast base
Verificar que el Plano de Control Multicast Utiliza BGP
- mdt overlay use-bgp: informa a los dispositivos que utilicen BGP MVPN type 5/6/7 como el protocolo de señal (contra los mensajes PIM)
- spt-only: palabra clave adicional informa al dispositivo que utilice solo árboles SPT en AnyCast RP Scenario. Dado que cada VTEP es un RP, no se utiliza ninguna ruta MVPN de tipo 6.
Leaf-01
!
vrf definition green
rd 1:1
!
address-family ipv4
mdt auto-discovery vxlan
mdt default vxlan 239.1.1.1 <-- Defines MDT default underlay group address
mdt overlay use-bgp [spt-only] <-- Required for VTEP to use MVPN Type 5/6/7 versus PIM for multicast control plane. (spt-only used for Anycast RP scenario)
Verificar grupo MDT
El grupo MDT es común a todos los escenarios, ya que este es el grupo de túnel exterior en el que se encapsula el grupo TRM.
Compruebe que el grupo MDT está correctamente programado en el lado de origen
- La interfaz entrante del grupo MDT es el loopback del lado de origen
- La interfaz saliente del grupo MDT es la interfaz subyacente
Verifique Leaf-01: la ruta multicast MDT es correcta en MRIB/MFIB
Leaf-01#sh ip mroute 239.1.1.1 172.16.254.3
(172.16.254.3, 239.1.1.1), 00:46:35/00:02:05, flags: FTx
Incoming interface: Loopback1, RPF nbr 0.0.0.0 <-- IIF is local loopback with 0.0.0.0 RPF indicating local
Outgoing interface list:
GigabitEthernet1/0/2, Forward/Sparse, 00:46:35/00:03:12 <-- OIF is the underlay uplink
Leaf-01#sh ip mfib 239.1.1.1 172.16.254.3
(172.16.254.3,239.1.1.1) Flags: HW
SW Forwarding: 2/0/150/0, Other: 1/1/0
HW Forwarding: 1458/0/156/0, Other: 0/0/0 <-- Hardware counters indicate the entry is operating in hardware and forwarding packets
Null0 Flags: A NS <--- Null0 (originated locally)
GigabitEthernet1/0/2 Flags: F NS <-- OIF is into the Underlay (Global route table)
Pkts: 0/0/1 Rate: 0 pps
Verify Leaf-01: Entradas FED para el grupo MDT
Leaf-01#sh platform software fed switch active ip mfib 239.1.1.1/32 172.16.254.3 detail <-- the detail option gives summary of the HW indexes
MROUTE ENTRY vrf 0 (172.16.254.3, 239.1.1.1/32) <-- vrf 0 = global for this MDT S,G pair
HW Handle: 139738317079128 Flags:
RPF interface: Null0(1)): <-- Leaf-01 the Source (Null0)
HW Handle:139738317079128 Flags:A
Number of OIF: 2
Flags: 0x4 Pkts : 71 <-- packets that used this adjacency (similar to mfib command, but shown at the FED layer)
OIF Details:
Null0 A <-- The incoming interface is Local Loopback1 and A-Accept flag set
GigabitEthernet1/0/2 F NS <-- The Underlay Outgoing Interface and F-Forward flag set
Htm: 0x7f175cc0beb8 Si: 0x7f175cc0a6b8 Di: 0x7f175cc09df8 Rep_ri: 0x7f175cc0a1d8 <-- The DI (dest index) handle
DI details
----------
Handle:0x7f175cc09df8 Res-Type:ASIC_RSC_DI Res-Switch-Num:255 Asic-Num:255 Feature-ID:AL_FID_L3_MULTICAST_IPV4 Lkp-ftr-id:LKP_FEAT_INVALID ref_count:1
priv_ri/priv_si Handle:(nil) Hardware Indices/Handles: index0:0x538d mtu_index/l3u_ri_index0:0x0 index1:0x538d mtu_index/l3u_ri_index1:0x0
Brief Resource Information (ASIC_INSTANCE# 1)
----------------------------------------
Destination index = 0x538d
pmap = 0x00000000 0x00000002
pmap_intf : [GigabitEthernet1/0/2] <-- FED has the correct programming for the OIF
==============================================================
Compruebe que el grupo MDT está correctamente programado en el lado del receptor
- La interfaz entrante del grupo MDT es la interfaz RPF de vuelta al Loopback del lado de origen
- La interfaz saliente del grupo MDT es la interfaz de túnel Encap/Decap
Verifique Leaf-02: la ruta multicast MDT es correcta en MRIB/MFIB
Leaf-02#sh ip mroute 172.16.254.3 239.1.1.1 <-- This is the Global MDT group
(172.16.254.3, 239.1.1.1), 00:23:35/00:01:09, flags: JTx <-- Source is Leaf-01 Lo1 IP
Incoming interface: GigabitEthernet1/0/2, RPF nbr 172.16.24.2
Outgoing interface list:
Tunnel0, Forward/Sparse, 00:23:35/00:00:24 <-- Decap Tunnel
Leaf-02#sh ip mfib 239.1.1.1 172.16.254.3
Default <-- Global routing table
(172.16.254.3,239.1.1.1) Flags: HW
SW Forwarding: 1/0/150/0, Other: 0/0/0
HW Forwarding: 5537/0/168/0, Other: 0/0/0 <-- Hardware counters indicate the entry is operating in hardware and forwarding packets
GigabitEthernet1/0/2 Flags: A <-- Accept via Underlay (Global) interface
Tunnel0, VXLAN Decap Flags: F NS <-- Forward to VxLAN decap Tunnel
Pkts: 0/0/1 Rate: 0 pps
Verify Leaf-02: entradas FED para el grupo MDT
Leaf-02#sh platform software fed switch active ip mfib 239.1.1.1/32 172.16.254.3 detail
MROUTE ENTRY vrf 0 (172.16.254.3, 239.1.1.1/32) <-- vrf 0 = global for this MDT S,G pair
HW Handle: 140397391831832 Flags:
RPF interface: GigabitEthernet1/0/2(57)): <-- RPF interface to 172.16.254.3
HW Handle:140397391831832 Flags:A
Number of OIF: 2
Flags: 0x4 Pkts : 1585 <-- packets that used this adjacency (similar to mfib command, but shown at the FED layer)
OIF Details:
Tunnel0 F NS <-- Send to decap tunnel to remove VxLAN header
(Adj: 0x73 ) <-- Tunnel0 Adjacency
GigabitEthernet1/0/2 A <-- Accept MDT packets from this interface
Htm: 0x7fb0d0f1f388 Si: 0x7fb0d0f1dc08 Di: 0x7fb0d0ed0438 Rep_ri: 0x7fb0d0ed07a8
RI details <-- Rewrite Index is used for VxLAN decapsulation
----------
Handle:0x7fb0d0ed07a8 Res-Type:ASIC_RSC_RI_REP Res-Switch-Num:255 Asic-Num:255 Feature-ID:AL_FID_L3_MULTICAST_IPV4 Lkp-ftr-id:LKP_FEAT_INVALID ref_count:1
priv_ri/priv_si Handle:(nil) Hardware Indices/Handles: index0:0x38 mtu_index/l3u_ri_index0:0x0 index1:0x38 mtu_index/l3u_ri_index1:0x0
Brief Resource Information (ASIC_INSTANCE# 0)
----------------------------------------
ASIC# 0
Replication list :
------------------
Total #ri : 6
Start_ri : 56
Common_ret : 0
Replication entry rep_ri 0x38 #elem = 1
0) ri[0]=0xE803 Dynamic port=88ri_ref_count:1 dirty=0
Leaf-02#sh platform hardware fed sw active fwd-asic resource asic all rewrite-index range 0xE803 0xE803
ASIC#:0 RI:59395 Rewrite_type:AL_RRM_REWRITE_L2_PAYLOAD_IPV4_EVPN_DECAP(118) Mapped_rii:LVX_EVPN_DECAP(246)
<...snip...>
Escenario 1. AnyCast RP (árboles solo SPT) IPv4 e IPv6
En este modo hay un RP ubicado en cada VTEP. Estos VTEPs no sincronizan las fuentes aprendidas a través de MSDP y no hay un árbol compartido. En su lugar, el modo MDT utiliza la información BGP para crear solamente árboles de multidifusión SPT. Este modo se denomina indistintamente modo SPT-only o modo distribuido Anycast-RP. En este modo, cada VTEP es el RP PIM. Por lo tanto, el árbol (*,G) de cada sitio se trunca en el propio VTEP local. No es necesario enviar uniones (*,G) ni MVPN RT-6 a través del fabric.
Diagrama de la red
Para este modo, considere 3 tipos de ruta BGP:
- EVPN Route-type 2. Esto permite a los otros PE que necesitan construir una ruta C-Multicast (MVPN type6/7) de regreso al PE de origen, conectar el C-Multicast Import RT adecuado para que el PE de origen pueda importar la ruta C-Multicast (RFC 6514 11.1.3) [RFC6514]. El uso de este VRI depende del comando "mdt overlay use-bgp" VRF.
- MVPN Route-type 5. Es lo mismo que en MVPN y es el anuncio de un origen/grupo de multidifusión disponible
- MVPN Route-type 7. La información de la capa IGMP o MLD y de EVPN Tipo-2 se utiliza para crear esta unión de tipo BGP. El Tipo-7 impulsa la creación del MRIB OIF en el lado de Origen.
Requisitos de EVPN tipo 2:
- El origen de multidifusión conectado directamente está en línea.
- FHR (VTEP de origen) verifica la adyacencia ARP (o ND) y CEF (confirma que la fuente está conectada directamente).
- FHR origina la actualización de EVPN de tipo 2 BGP
Requisitos de MVPN de tipo 5:
- Se ha resuelto el requisito para la conexión directa de origen
- RP es local, por lo que FHR se registra a sí mismo
- FHR origina la actualización de BGP MVPN de tipo 5
Requisitos de MVPN de tipo 7:
- Hay una entrada EVPN de tipo 2 (necesaria para construir la ruta C-Multicast de tipo 7 con VRI correcto y enviada desde VTEP de origen)
- Hay una entrada de tipo 5 de MVPN (necesaria para resolver qué par de origen/grupo está disponible para la unión a SPT)
- El informe de afiliación de IGMP o MLD ha sido recibido y procesado por LHR VTEP
- La interfaz LHR VTEP RPF es la interfaz Fabric L3VNI
Verificar las Rutas BGP EVPN y MVPN
Verify Leaf-01: se crea el EVPN Type-2
### IPv4 ###
Leaf-01#sh bgp l2vpn evpn all route-type 2 0 F4CFE24334C5 10.1.101.11
...or you can also use:
Leaf-01#sh bgp l2vpn evpn detail [2][172.16.254.3:101][0][48][F4CFE24334C5][32][10.1.101.11]/24
BGP routing table entry for [2][172.16.254.3:101][0][48][F4CFE24334C5][32][10.1.101.11]/24, version 6
Paths: (1 available, best #1, table evi_101)
Advertised to update-groups:
1
Refresh Epoch 1
Local
:: (via default) from 0.0.0.0 (172.16.255.3) <-- Leaf-01 locally created
Origin incomplete, localpref 100, weight 32768, valid, sourced, local, best
EVPN ESI: 00000000000000000000, Label1 10101, Label2 50901
Extended Community: RT:1:1 RT:65001:101 MVPN AS:65001:0.0.0.0
MVPN VRF:172.16.255.3:2 ENCAP:8 Router MAC:10B3.D56A.8FC8 <-- MVPN VRI RT is part of the EVPN Type-2
Local irb vxlan vtep:
vrf:green, l3-vni:50901 <-- Vrf and VxLAN tag
local router mac:10B3.D56A.8FC8
core-irb interface:Vlan901 <-- L3VNI SVI
vtep-ip:172.16.254.3 <-- Leaf-01 VTEP
rx pathid: 0, tx pathid: 0x0
Updated on Dec 16 2020 17:40:29 UTC
### IPv6 ###
Leaf-01#sh bgp l2vpn evpn all route-type 2 0 F4CFE24334C1 FC00:1:101::11
...or you can also use:
Leaf-01#sh bgp l2vpn evpn detail [2][172.16.254.3:101][0][48][F4CFE24334C1][128][FC00:1:101::11]/36
BGP routing table entry for [2][172.16.254.3:101][0][48][F4CFE24334C1][128][FC00:1:101::11]/36, version 6
Paths: (1 available, best #1, table evi_101)
Advertised to update-groups:
1
Refresh Epoch 1
Local
:: (via default) from 0.0.0.0 (172.16.255.3) <-- Leaf-01 locally created
Origin incomplete, localpref 100, weight 32768, valid, sourced, local, best
EVPN ESI: 00000000000000000000, Label1 10101, Label2 50901
Extended Community: RT:1:1 RT:65001:101 MVPN AS:65001:0.0.0.0
MVPN VRF:172.16.255.3:2 ENCAP:8 Router MAC:10B3.D56A.8FC8 <-- MVPN VRI RT is part of the EVPN Type-2
Local irb vxlan vtep:
vrf:green, l3-vni:50901
local router mac:10B3.D56A.8FC8
core-irb interface:Vlan901 <-- L3VNI SVI
vtep-ip:172.16.254.3 <-- Leaf-01 VTEP
rx pathid: 0, tx pathid: 0x0
Updated on Mar 22 2021 19:54:18 UTC
Verifique Leaf-01: ARP/IPv6 ND y los debugs EVPN muestran que ARP/ND se aprende, luego se crea y se envía el tipo de ruta 2
### IPv4 ###
Leaf-01#sh debugging
ARP:
ARP packet debugging is on
BGP L2VPN EVPN:
BGP updates debugging is on for address family: L2VPN E-VPN
BGP update events debugging is on for address family: L2VPN E-VPN
*Dec 17 17:00:06.480: IP ARP: rcvd rep src 10.1.101.11 f4cf.e243.34c5, dst 10.1.101.11 Vlan101 tableid 2 <-- Multicast Source ARP
*Dec 17 17:00:06.481: BGP: EVPN Rcvd pfx: [2][172.16.254.3:101][0][48][F4CFE24334C5][32][10.1.101.11]/24, net flags: 0 <-- BGP Triggered Type-2 creation
*Dec 17 17:00:06.481: TRM communities added to sourced RT2 <-- TRM extended VRI communities being injected into EVPN Type-2
*Dec 17 17:00:06.481: BGP(10): update modified for [2][172.16.254.3:101][0][48][F4CFE24334C5][32][10.1.101.11]/30 <-- Modifying the update
*Dec 17 17:00:06.481: BGP(10): 172.16.255.1 NEXT_HOP set to vxlan local vtep-ip 172.16.254.3 for net [2][172.16.254.3:101][0][48][F4CFE24334C5][32][10.1.101.11]/24
*Dec 17 17:00:06.481: BGP(10): update modified for [2][172.16.254.3:101][0][48][F4CFE24334C5][32][10.1.101.11]/30
*Dec 17 17:00:06.481: BGP(10): (base) 172.16.255.1 send UPDATE (format) [2][172.16.254.3:101][0][48][F4CFE24334C5][32][10.1.101.11]/30, next 172.16.254.3, metric 0, path Local, extended community RT:1:1 RT:65001:101 MVPN AS:65001:0.0.0.0 MVPN VRF:172.16.255.3:2 ENCAP:8 Router MAC:10B3.D56A.8FC8
<--- Final update sent to RR with standard EVPN community info and required MVPN community attributes
### IPv6 ###
Leaf-01#debug ipv6 nd
ICMP Neighbor Discovery events debugging is on
ICMP ND HA events debugging is ON
IPv6 ND:
Mar 23 14:29:51.935: ICMPv6-ND: (Vlan101,FC00:1:101::11) Resolution request
Mar 23 14:29:51.935: ICMPv6-ND: (Vlan101,FC00:1:101::11) DELETE -> INCMP
Mar 23 14:29:51.935: ICMPv6-ND HA: in Update Neighbor Cache: old state 6 new state 0
Mar 23 14:29:51.935: ICMPv6-ND HA: add or delete entry not synced as no peer detected
Mar 23 14:29:51.936: ICMPv6-ND: (Vlan101,FC00:1:101::11) Sending NS
Mar 23 14:29:51.936: ICMPv6-ND: (Vlan101,FC00:1:101::11) Queued data for resolution
Mar 23 14:29:51.953: ICMPv6-ND: (Vlan101,FC00:1:101::11) Received NA from FC00:1:101::11
Mar 23 14:29:51.953: ICMPv6-ND: Validating ND packet options: valid
Mar 23 14:29:51.953: ICMPv6-ND: (Vlan101,FC00:1:101::11) LLA f4cf.e243.34c1
Mar 23 14:29:51.953: ICMPv6-ND HA: modify entry not synced as no peer detected
Mar 23 14:29:51.953: ICMPv6-ND: (Vlan101,FC00:1:101::11) INCMP -> REACH <-- peer is reachable
Leaf-01#debug bgp l2vpn evpn updates
Leaf-01#debug bgp l2vpn evpn updates events
BGP L2VPN EVPN:
Mar 23 14:11:56.462: BGP: EVPN Rcvd pfx: [2][172.16.254.3:101][0][48][F4CFE24334C1][128][FC00:1:101::11]/36, net flags: 0 <-- BGP Triggered Type-2 creation
Mar 23 14:11:57.462: TRM communities added to sourced RT2
ar 23 14:11:57.474: BGP(10): update modified for [2][172.16.254.3:101][0][48][F4CFE24334C1][128][FC00:1:101::11]/42
Mar 23 14:11:57.474: BGP(10): 172.16.255.1 NEXT_HOP set to vxlan local vtep-ip 172.16.254.3 for net [2][172.16.254.3:101][0][48][F4CFE24334C1][128][FC00:1:101::11]/36
Mar 23 14:11:57.474: BGP(10): update modified for [2][172.16.254.3:101][0][48][F4CFE24334C1][128][FC00:1:101::11]/42
Mar 23 14:11:57.474: BGP(10): (base) 172.16.255.1 send UPDATE (format) [2][172.16.254.3:101][0][48][F4CFE24334C1][128][FC00:1:101::11]/42, next 172.16.254.3, metric 0, path Local, extended community RT:1:1 RT:65001:101 MVPN AS:65001:0.0.0.0 MVPN VRF:172.16.255.3:2 ENCAP:8 Router MAC:10B3.D56A.8FC8
<--- Final update sent to RR with standard EVPN community info and required MVPN community attributes
Verifique que Leaf-02: Source side Route-type 2 se aprende en BGP en el lado del receptor
### IPv4 ###
Leaf-02#sh bgp l2vpn evpn all | b 10.1.101.11
* i [2][172.16.254.3:101][0][48][F4CFE24334C5][32][10.1.101.11]/24 <-- Remote VTEP route-type 2
172.16.254.3 0 100 0 ?
*>i 172.16.254.3 0 100 0 ? <-- IP of Leaf01 Lo1
Leaf-02#sh bgp l2vpn evpn route-type 2 0 F4CFE24334C5 10.1.101.11
...or you can also use:
Leaf-02#sh bgp l2vpn evpn detail [2][172.16.254.3:101][0][48][F4CFE24334C5][32][10.1.101.11]/24
BGP routing table entry for [2][172.16.254.3:101][0][48][F4CFE24334C5][32][10.1.101.11]/24, version 175
Paths: (2 available, best #2, table EVPN-BGP-Table) <-- In BGP EVPN table
Flag: 0x100
Not advertised to any peer
Refresh Epoch 2
Local
172.16.254.3 (metric 3) (via default) from 172.16.255.2 (172.16.255.2)
Origin incomplete, metric 0, localpref 100, valid, internal
EVPN ESI: 00000000000000000000, Label1 10101, Label2 50901
Extended Community: RT:1:1 RT:65001:101 MVPN AS:65001:0.0.0.0
MVPN VRF:172.16.255.3:2 ENCAP:8 Router MAC:10B3.D56A.8FC8
Originator: 172.16.255.3, Cluster list: 172.16.255.2
rx pathid: 0, tx pathid: 0
Updated on Dec 14 2020 19:58:57 UTC
MVPN AS:65001:0.0.0.0 <-- MVPN Autonomous System
MVPN VRF:172.16.255.3:2 <-- VRI Extended Community to be used in MVPN Type-7
Router MAC:10B3.D56A.8FC8 <-- Leaf-01 RMAC
Label2 50901 <-- L3VNI 50901
### IPv6 ###
Leaf-02#sh bgp l2vpn evpn all | b FC00:1:101::11
* i [2][172.16.254.3:101][0][48][F4CFE24334C1][128][FC00:1:101::11]/36
172.16.254.3 0 100 0 ?
*>i 172.16.254.3 0 100 0 ? <-- IP of Leaf01 Lo1
Leaf-02#sh bgp l2vpn evpn route-type 2 0 F4CFE24334C1 FC00:1:101::11
...or you can also use:
Leaf-02#sh bgp l2vpn evpn detail [2][172.16.254.3:101][0][48][F4CFE24334C1][128][FC00:1:101::11]/36
BGP routing table entry for [2][172.16.254.3:101][0][48][F4CFE24334C1][128][FC00:1:101::11]/36, version 659
Paths: (2 available, best #2, table EVPN-BGP-Table) <-- In BGP EVPN table
Flag: 0x100
Not advertised to any peer
Refresh Epoch 2
Local
172.16.254.3 (metric 3) (via default) from 172.16.255.2 (172.16.255.2)
Origin incomplete, metric 0, localpref 100, valid, internal
EVPN ESI: 00000000000000000000, Label1 10101, Label2 50901
Extended Community: RT:1:1 RT:65001:101 MVPN AS:65001:0.0.0.0
MVPN VRF:172.16.255.3:2 ENCAP:8 Router MAC:10B3.D56A.8FC8
Originator: 172.16.255.3, Cluster list: 172.16.255.2
rx pathid: 0, tx pathid: 0
Updated on Mar 23 2021 14:11:57 UTC
MVPN AS:65001:0.0.0.0 <-- MVPN Autonomous System
MVPN VRF:172.16.255.3:2 <-- VRI Extended Community to be used in MVPN Type-7
Router MAC:10B3.D56A.8FC8 <-- Leaf-01 RMAC
Label2 50901 <-- L3VNI 50901
Verifique Leaf-02: Source Route-type 5 se aprende en BGP en Receiver VTEP Leaf-02
### IPv4 ###
Leaf-02#sh bgp ipv4 mvpn all route-type 5 10.1.101.11 226.1.1.1
...or you can also use:
Leaf-02#sh bgp ipv4 mvpn detail [5][1:1][10.1.101.11][226.1.1.1]/18
BGP routing table entry for [5][1:1][10.1.101.11][226.1.1.1]/18, version 72 <-- Type-5 contains advertised S,G pair
Paths: (2 available, best #1, table MVPNv4-BGP-Table, not advertised to EBGP peer) <-- In BGP IPv4 MVPN table
Flag: 0x100
Not advertised to any peer
Refresh Epoch 1
Local
172.16.255.3 (metric 3) from 172.16.255.2 (172.16.255.2) <-- Loopback0 of Leaf-01
Origin incomplete, metric 0, localpref 100, valid, internal
Community: no-export
Extended Community: RT:1:1
Originator: 172.16.255.3, Cluster list: 172.16.255.2
rx pathid: 0, tx pathid: 0
Updated on Dec 15 2020 16:54:53 UTC
### IPv6 ###
Leaf-02#sh bgp ipv6 mvpn all route-type 5 FC00:1:101::11 FF06:1::1
...or you can also use:
Leaf-02#sh bgp ipv6 mvpn detail [5][1:1][FC00:1:101::11][FF06:1::1]/42
BGP routing table entry for [5][1:1][FC00:1:101::11][FF06:1::1]/42, version 11 <-- Type-5 contains advertised S,G pair
Paths: (2 available, best #1, table MVPNV6-BGP-Table, not advertised to EBGP peer) <-- In BGP IPv6 MVPN table
Flag: 0x100
Not advertised to any peer
Refresh Epoch 1
Local
172.16.255.3 (metric 3) from 172.16.255.2 (172.16.255.2) <-- Loopback0 of Leaf-01
Origin incomplete, metric 0, localpref 100, valid, internal
Community: no-export
Extended Community: RT:1:1
Originator: 172.16.255.3, Cluster list: 172.16.255.2
rx pathid: 0, tx pathid: 0
Updated on Mar 23 2021 15:13:06 UTC
Verifique Leaf-02: ha necesitado información BGP de Leaf-01 para crear el Type-7. El requisito final es que IGMP o MLD haya procesado un informe de afiliación que informe al VTEP que hay un receptor interesado.
### IPv4 ###
Leaf-02#sh ip igmp snooping groups vlan 102
Vlan Group Type Version Port List
-----------------------------------------------------------------------
102 226.1.1.1 igmp v2 Gi1/0/10 <-- Receiver joined on Gi1/0/10
### IPv6 ###
Leaf-02#sh ipv6 mld vrf green groups detail
Interface: Vlan102 <-- Join on Vlan 102
Group: FF06:1::1 <-- Group joined
Uptime: 06:38:25
Router mode: EXCLUDE (Expires: 00:02:14)
Host mode: INCLUDE
Last reporter: FE80::46D3:CAFF:FE28:6CC1 <-- MLD join from Receiver link-local address
Source list is empty <-- ASM join, no sources listed
Leaf-02#sh ipv6 neighbors vrf green
IPv6 Address Age Link-layer Addr State Interface
FE80::46D3:CAFF:FE28:6CC1 0 44d3.ca28.6cc1 REACH Vl102 <-- Receiver IP & MAC
Leaf-02#sh ipv6 mld snooping address vlan 102 <-- If MLD snooping is on, it can be checked as well
Vlan Group Type Version Port List
-----------------------------------------------------------------------
102 FF06:1::1 mld v2 Gi1/0/10 <-- Receiver joined on Gi1/0/10
Verifique Leaf-02: MVPN Debugs show Route-type 7 se crea cuando llega el informe de membresía IGMP/MLD y ya están instalados los EVPN Type-2 y Type-5 requeridos.
### IPv4 ###
Leaf-02#debug bgp ipv4 mvpn updates
Leaf-02#debug bgp ipv4 mvpn updates events
*Dec 14 19:41:57.645: BGP[15] MVPN: add c-route, type 7, bs len 0 asn=0, rd=1:1,
*Dec 14 19:41:57.645: source=10.1.101.11/4,
*Dec 14 19:41:57.645: group=226.1.1.1/4,
*Dec 14 19:41:57.645: nexthop=172.16.254.3, <-- Source is via Leaf-01 IP
*Dec 14 19:41:57.645: len left = 0
*Dec 14 19:41:57.645: BGP[14] MVPN umh lookup: vrfid 2, source 10.1.101.11
*Dec 14 19:41:57.645: BGP[4] MVPN umh lookup: vrfid 2, source 10.1.101.11, net 1:1:10.1.101.11/32, 1:1:10.1.101.11/32 with matching nexthop 172.16.254.3, remote-rd [172.16.]: 0x9:65001:0.0.0.0, 0x10B:172.16.255.3:2,
*Dec 14 19:41:57.646: BGP: MVPN(15) create local route [7][172.16.254.3:101][65001][10.1.101.11/32][226.1.1.1/32]/22
*Dec 14 19:41:57.646: BGP[15] MVPN: add c-route, type 7, bs len 0 asn=65001, rd=1:1,
### IPv6 ###
Leaf-02#debug bgp ipv6 mvpn updates
Leaf-02#debug bgp ipv6 mvpn updates events
Mar 23 15:46:11.171: BGP[16] MVPN: add c-route, type 7, bs len 0 asn=0, rd=1:1,
Mar 23 15:46:11.171: source=FC00:1:101::11/16,
Mar 23 15:46:11.171: group=FF06:1::1/16,
Mar 23 15:46:11.171: nexthop=::FFFF:172.16.254.3, <-- IPv4 next hop of Leaf-01
Mar 23 15:46:11.171: len left = 0
Mar 23 15:46:11.171: BGP[19] MVPN umh lookup: vrfid 2, source FC00:1:101::11
Mar 23 15:46:11.171: BGP[5] MVPN umh lookup: vrfid 2, source FC00:1:101::11, net [1:1]FC00:1:101::11/128, [1:1]FC00:1:101::11/128 with matching nexthop ::FFFF:172.16.254.3, remote-rd [172.16.]: 0x9:65001:0.0.0.0, 0x10B:172.16.255.3:2,
Mar 23 15:46:11.172: BGP: MVPN(16) create local route [7][172.16.254.3:101][65001][FC00:1:101::11][FF06:1::1]/46
Mar 23 15:46:11.172: BGP[16] MVPN: add c-route, type 7, bs len 0 asn=65001, rd=1:1,
Verify Leaf-01: MVPN Type-7 received from Leaf-02
### IPv4 ###
Leaf-01#sh bgp ipv4 mvpn all route-type 7 172.16.254.3:101 65001 10.1.101.11 226.1.1.1
...or you can also use:
Leaf-01#sh bgp ipv4 mvpn detail [7][172.16.254.3:101][65001][10.1.101.11/32][226.1.1.1/32]/22
BGP routing table entry for [7][172.16.254.3:101][65001][10.1.101.11/32][226.1.1.1/32]/22, version 76
Paths: (2 available, best #1, table MVPNv4-BGP-Table) <-- In BGP IPv4 MVPN table
Not advertised to any peer
Refresh Epoch 1
Local
172.16.255.4 (metric 3) from 172.16.255.2 (172.16.255.2) <-- loopback of Leaf-02 Receiver VTEP
Origin incomplete, metric 0, localpref 100, valid, internal
Extended Community: RT:172.16.255.3:2 <-- The VRI derived from EVPN Type-2 and added to the MVPN Type-7
Originator: 172.16.255.4, Cluster list: 172.16.255.2
rx pathid: 0, tx pathid: 0
Updated on Dec 15 2020 14:14:38 UTC
### IPv6 ###
Leaf-01#sh bgp ipv6 mvpn all route-type 7 172.16.254.3:101 65001 FC00:1:101::11 FF06:1::1
...or you can also use:
Leaf-01#sh bgp ipv6 mvpn detail [7][172.16.254.3:101][65001][FC00:1:101::11][FF06:1::1]/46
BGP routing table entry for [7][172.16.254.3:101][65001][FC00:1:101::11][FF06:1::1]/46, version 45
Paths: (2 available, best #1, table MVPNV6-BGP-Table) <-- In BGP IPv6 MVPN table
Not advertised to any peer
Refresh Epoch 1
Local
172.16.255.4 (metric 3) from 172.16.255.1 (172.16.255.1) <-- loopback of Leaf-02 Receiver VTEP
Origin incomplete, metric 0, localpref 100, valid, internal, best
Extended Community: RT:172.16.255.3:2 <-- The VRI derived from EVPN Type-2 and added to the MVPN Type-7
Originator: 172.16.255.4, Cluster list: 172.16.255.1
rx pathid: 0, tx pathid: 0x0
Updated on Mar 23 2021 15:46:11 UTC
Verifique Leaf-01: MVPN Debugs show Route-type 7 received with the MVPN VRI Route-Target
*Dec 17 16:16:31.923: BGP(15): 172.16.255.2 rcvd UPDATE w/ attr: nexthop 172.16.255.4, origin ?, localpref 100, metric 0, originator 172.16.255.4, clusterlist 172.16.255.2, extended community RT:172.16.255.3:2 <-- VRI RT
*Dec 17 16:16:31.923: BGP(15): 172.16.255.2 rcvd [7][172.16.254.3:101][65001][10.1.101.11/32][226.1.1.1/32]/22 <-- Received MVPN Type-7
<...only update from Spine-02 172.16.255.2 ...>
*Dec 17 16:16:31.923: BGP(15): skip vrf default table RIB route [7][172.16.254.3:101][65001][10.1.101.11/32][226.1.1.1/32]/22
*Dec 17 16:16:31.924: BGP(15): add RIB route (0:0)[7][1:1][65001][10.1.101.11/32][226.1.1.1/32]/22
(Skipping IPv6, see the debugs demonstrated in previous steps)
Verificar Hoja-02: La tabla BGP completa contiene el Tipo-2 de EVPN Leaf-01 y el Tipo-5 de MVPN, y el Tipo-7 generado por el Receptor Hoja-02
### IPv4 ###
Leaf-02#sh bgp l2vpn evpn all | b 10.1.101.11
* i [2][172.16.254.3:101][0][48][F4CFE24334C5][32][10.1.101.11]/24 <-- Remote VTEP route-type 2
172.16.254.3 0 100 0 ?
*>i 172.16.254.3 0 100 0 ? <-- IP of Leaf01 Lo1
Leaf-02#sh bgp ipv4 mvpn all
Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 1:1 (default for vrf green) <-- default RD for vrf green
*>i [5][1:1][10.1.101.11][226.1.1.1]/18 <-- Type-5, source & group
172.16.255.3 0 100 0 ? <-- Next hop Leaf-01 IP
* i 172.16.255.3 0 100 0 ?
Route Distinguisher: 172.16.254.3:101 <-- MVPN RD sent from Source Leaf-01
*> [7][172.16.254.3:101][65001][10.1.101.11/32][226.1.1.1/32]/22 <-- Type-7 BGP Join Entry
0.0.0.0 32768 ? <-- Locally created (0.0.0.0) by Leaf-02
### IPv6 ###
Leaf-02#sh bgp l2vpn evpn all | b FC00:1:101::11
* i [2][172.16.254.3:101][0][48][F4CFE24334C1][128][FC00:1:101::11]/36 <-- Remote VTEP route-type 2
172.16.254.3 0 100 0 ?
*>i 172.16.254.3 0 100 0 ? <-- IP of Leaf-01 Lo1
Leaf-02#sh bgp ipv6 mvpn all
Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 1:1 (default for vrf green) <-- default RD for vrf green
*>i [5][1:1][FC00:1:101::11][FF06:1::1]/42 <-- Type-5, source & group
172.16.255.3 0 100 0 ? <-- IPv4 Next hop Leaf-01 IP
* i 172.16.255.3 0 100 0 ?
Route Distinguisher: 172.16.254.3:101 <-- MVPN RD sent from Source Leaf-01
*> [7][172.16.254.3:101][65001][FC00:1:101::11][FF06:1::1]/46 <-- Type-7 BGP Join Entry
:: 32768 ? <-- Locally created (::) by Leaf-02
Verifique el grupo TRM Leaf-01 (FHR)
Compruebe que los grupos MDT y TRM están formados correctamente en el lado de origen.
- La interfaz entrante del grupo TRM es la SVI asociada al cliente VRF
- La interfaz saliente del grupo TRM es el L3VNI SVI
Verifique Leaf-01: el grupo TRM MRIB/MFIB
### IPv4 ###
Leaf-01#sh ip mroute vrf green 226.1.1.1 10.1.101.11
(10.1.101.11, 226.1.1.1), 02:57:56/00:03:14, flags: FTGqx <-- Flags: BGP S-A Route
Incoming interface: Vlan101, RPF nbr 0.0.0.0 <-- Local to Vlan101 Direct connected source
Outgoing interface list:
Vlan901, Forward/Sparse, 02:57:56/stopped <-- OIF is VxLAN L3VNI
Leaf-01#sh ip mfib vrf green 226.1.1.1 10.1.101.11
VRF green <-- Tenant VRF
(10.1.101.11,226.1.1.1) Flags: HW
SW Forwarding: 1/0/100/0, Other: 0/0/0
HW Forwarding: 5166/0/118/0, Other: 0/0/0 <-- Hardware counters indicate the entry is operating in hardware and forwarding packets
Vlan101 Flags: A <-- Accept flag set on Connected Source SVI
Vlan102 Flags: F NS
Pkts: 0/0/1 Rate: 0 pps
Vlan901, VXLAN v4 Encap (50901, 239.1.1.1) Flags: F <-- Forward via Vlan 901. Use MDT group 239.1.1.1, vxlan tag 50901
Pkts: 0/0/0 Rate: 0 pps
### IPv6 ###
Leaf-01#sh ipv6 mroute vrf green
(FC00:1:101::11, FF06:1::1), 01:01:00/00:01:08, flags: SFTGq <-- Flags: q - BGP S-A Route, G - BGP Signal Received
Incoming interface: Vlan101
RPF nbr: FE80::F6CF:E2FF:FE43:34C1 <-- link local address of Source
Immediate Outgoing interface list:
Vlan901, Forward, 01:01:00/never <-- OIF is VxLAN L3VNI
Leaf-01#sh ipv6 mfib vrf green FF06:1::1
VRF green <-- Tenant VRF
(FC00:1:101::11,FF06:1::1) Flags: HW
SW Forwarding: 0/0/0/0, Other: 1/0/1
HW Forwarding: 1968/0/118/0, Other: 0/0/0 <-- Hardware counters indicate the entry is operating in hardware and forwarding packets
Vlan101 Flags: A NS <-- Accept flag set on Connected Source SVI
Vlan901, VXLAN v4 Encap (50901, 239.1.1.1) Flags: F <-- Forward via Vlan 901. Use MDT group 239.1.1.1, vxlan tag 50901
Pkts: 0/0/0 Rate: 0 pps
Verify Leaf-01: el grupo TRM en FED
### IPv4 ###
Leaf-01#sh platform software fed switch active ip mfib vrf green 226.1.1.1/32 10.1.101.11
Multicast (S,G) Information
VRF : 2 <-- VRF ID 2 = vrf green (from "show vrf detail")
Source Address : 10.1.101.11
HTM Handler : 0x7f175cc08578
SI Handler : 0x7f175cc06ea8
DI Handler : 0x7f175cc067c8
REP RI handler : 0x7f175cc06b38
Flags : {Svl}
Packet count : 39140 <-- packets that used this adjacency (similar to mfib command, but shown at the FED layer)
State : 4
RPF :
Vlan101 A <-- Accept on Vlan 101 in Tenant vrf green
OIF :
Vlan102 F NS
Vlan101 A
Vlan901 F {Remote} <-- Forward via L3VNI interface
(Adj: 0x6a ) <-- Adjacency for this entry
### IPv6 ###
Leaf-01#sh plat soft fed switch active ipv6 mfib vrf green FF06:1::1/128 FC00:1:101::11
Multicast (S,G) Information
VRF : 2 <-- VRF ID 2 = vrf green (from "show vrf detail")
Source Address : fc00:1:101::11
HTM Handler : 0x7fba88d911b8
SI Handler : 0x7fba88fc4348
DI Handler : 0x7fba88fc8dc8
REP RI handler : 0x7fba88fc8fd8
Flags : {Svl}
Packet count : 2113 <-- packets that used this adjacency (similar to mfib command, but shown at the FED layer)
State : 4
RPF :
Vlan101 A {Remote} <-- Accept on Vlan 101 in Tenant vrf green (says remote, but this is a local host)
OIF :
Vlan101 A {Remote}
Vlan901 F {Remote} <-- Forward via L3VNI interface
(Adj: 0x7c ) <-- Adjacency for this entry
Verifique Leaf-01: la adyacencia es correcta
### IPv4 ###
Leaf-01#sh platform software fed switch active ip adj
IPV4 Adj entries
dest if_name dst_mac si_hdl ri_hdl pd_flags adj_id Last-modified
---- ------- ------- ------ ------ -------- ----- ------------------------
239.1.1.1 nve1.VNI50901 4500.0000.0000 0x7f175ccd8c38 0x7f175ccd8de8 0x60 0x6a 2020/12/16 17:39:55.747
*** Adjacency 0x6a details ***
Destination = the MDT tunnel multicast group 239.1.1.1
Interface = nve1.VNI50901 (the L3VNI 50901)
### IPv6 ###
Leaf-01#sh platform software fed switch active ipv6 adj
IPV6 Adj entries
dest if_name dst_mac si_hdl ri_hdl pd_flags adj_id Last-modified
---- ------- ------- ------ ------ -------- ------ -------------
239.1.1.1 nve1.VNI50901 4500.0000.0000 0x7fba88cf9fc8 0x7fba88cfa248 0x60 0x7c 2021/03/22 19:54:09.831
*** Adjacency 0x7c details ***
Destination = the MDT tunnel multicast group 239.1.1.1
Interface = nve1.VNI50901 (the L3VNI 50901)
Verifique el grupo TRM Leaf-02 (LHR)
Compruebe que los grupos MDT y TRM están formados correctamente en el lado del receptor.
- La interfaz entrante del grupo TRM es la SVI asociada al L3VNI
- La interfaz saliente del grupo TRM es la SVI del cliente donde se procesó la unión IGMP.
Verify Leaf-02: la ruta TRM (ruta de multidifusión de arrendatario) en MRIB/MFIB
Leaf-02#sh ip mroute vrf green 226.1.1.1 10.1.101.11 <-- The TRM Client group
(10.1.101.11, 226.1.1.1), 00:26:03/00:02:37, flags: TgQ
Incoming interface: Vlan901, RPF nbr 172.16.254.3 <-- Via L3VNI, RPF to Leaf-01
Outgoing interface list:
Vlan102, Forward/Sparse, 00:26:03/00:03:10 <-- Client Receiver Vlan
Leaf-02#sh ip mfib vrf green 226.1.1.1 10.1.101.11
VRF green <--- The Tenant VRF
(10.1.101.11,226.1.1.1) Flags: HW
SW Forwarding: 1/0/100/0, Other: 0/0/0
HW Forwarding: 39013/0/126/0, Other: 0/0/0 <-- Hardware counters indicate the entry is operating in hardware and forwarding packets
Vlan901, VXLAN Decap Flags: A <-- L3VNI Accept and decapsulate from VxLAN
Vlan102 Flags: F NS <-- Forward to the Tenant Vlan
Pkts: 0/0/1 Rate: 0 pps
Verify Leaf-02: el grupo TRM en FED
### IPv4 ###
Leaf-02#sh platform software fed switch active ip mfib vrf green 226.1.1.1/32 10.1.101.11 detail <-- Use detail option to resolve DI (Dest Index)
MROUTE ENTRY vrf 2 (10.1.101.11, 226.1.1.1/32)
HW Handle: 140397391947768 Flags: {Svl}
RPF interface: Vlan901(60)): SVI <-- RPF interface = L3VNI SVI Vlan901
HW Handle:140397391947768 Flags:A {Remote}
Number of OIF: 2
Flags: 0x4 Pkts : 39387 <-- packets that used this adjacency (similar to mfib command, but shown at the FED layer)
OIF Details:
Vlan102 F NS <-- Client Vlan
Vlan901 A {Remote} <-- Accept interface is RPF to source via Remote EVPN next hop
(Adj: 0xf80003c1 ) <-- Adj for vlan 901(show plat soft fed sw active ipv4 adj)
Htm: 0x7fb0d0edfb48 Si: 0x7fb0d0ee9158 Di: 0x7fb0d0eca8f8 Rep_ri: 0x7fb0d0ef2b98
DI details <-- Dest index (egress interface) details
----------
Handle:0x7fb0d0eca8f8 Res-Type:ASIC_RSC_DI Res-Switch-Num:255 Asic-Num:255 Feature-ID:AL_FID_L3_MULTICAST_IPV4 Lkp-ftr-id:LKP_FEAT_INVALID ref_count:1
priv_ri/priv_si Handle:(nil) Hardware Indices/Handles: index0:0x538b mtu_index/l3u_ri_index0:0x0 index1:0x538b mtu_index/l3u_ri_index1:0x0
Brief Resource Information (ASIC_INSTANCE# 1) <-- Gi1/0/10 is mapped to instance 1
----------------------------------------
Destination index = 0x538b
pmap = 0x00000000 0x00000200
pmap_intf : [GigabitEthernet1/0/10] <-- Maps to Gi1/0/10, the port toward the client
==============================================================
### IPv6 ###
Leaf-02#sh platform software fed switch active ipv6 mfib vrf green FF06:1::1/128 FC00:1:101::11 detail
MROUTE ENTRY vrf 2 (fc00:1:101::11, ff06:1::1/128)
HW Handle: 139852137577736 Flags: {Svl}
RPF interface: Vlan901(62)): SVI <-- RPF to Source L3VNI SVI 901
HW Handle:139852137577736 Flags:A {Remote}
Number of OIF: 2
Flags: 0x4 Pkts : 7445 <-- Packets use this Entry
OIF Details:
Vlan102 F NS <-- F - Forward. The OIF Vlan SVI 901
Vlan901 A {Remote}
(Adj: 0xf80003e2 ) <-- Adj for vlan 901 (show plat soft fed sw active ipv6 adj)
Htm: 0x7f31dcfee238 Si: 0x7f31dcfba5d8 Di: 0x7f31dcfc2358 Rep_ri: 0x7f31dcfcb1a8
DI details
----------
Handle:0x7f31dcfc2358 Res-Type:ASIC_RSC_DI Res-Switch-Num:255 Asic-Num:255 Feature-ID:AL_FID_L3_MULTICAST_IPV6 Lkp-ftr-id:LKP_FEAT_INVALID ref_count:1
priv_ri/priv_si Handle:(nil) Hardware Indices/Handles: index0:0x5381 mtu_index/l3u_ri_index0:0x0 index1:0x5381 mtu_index/l3u_ri_index1:0x0
Brief Resource Information (ASIC_INSTANCE# 1) <-- Gig1/0/10 is mapped to Instance 1
----------------------------------------
Destination index = 0x5381
pmap = 0x00000000 0x00000200
pmap_intf : [GigabitEthernet1/0/10] <-- Maps to Gig1/0/10, the port toward the client
==============================================================
Leaf-02#sh platform software fed switch active ifm mappings
Interface IF_ID Inst Asic Core Port SubPort Mac Cntx LPN GPN Type Active
GigabitEthernet1/0/10 0x12 1 0 1 9 0 5 15 10 10 NIF Y <-- Instance 1 of ASIC 0
Verify Leaf-02: La captura de paquetes realizada muestra el grupo de túnel MDT externo con tráfico de cliente interno
Leaf-02#sh mon ca 1 parameter
monitor capture 1 interface GigabitEthernet1/0/2 IN
monitor capture 1 match any
monitor capture 1 buffer size 10
monitor capture 1 limit pps 1000
### IPv4 ###
Leaf-02#sh mon capture 1 buffer detailed
Ethernet II, Src: 7c:21:0d:bd:2c:d6 (7c:21:0d:bd:2c:d6), Dst: 01:00:5e:01:01:01 (01:00:5e:01:01:01) <-- MAC is matching 239.1.1.1
Type: IPv4 (0x0800) <-- IPv4 outer packet
Internet Protocol Version 4, Src: 172.16.254.3, Dst: 239.1.1.1 <- Leaf-01 Source IP and MDT outer tunnel Group
0100 .... = Version: 4
.... 0101 = Header Length: 20 bytes (5)
Time to live: 253
User Datagram Protocol, Src Port: 65287, Dst Port: 4789 <-- VxLAN UDP port 4789
Virtual eXtensible Local Area Network
Flags: 0x0800, VXLAN Network ID (VNI)
Group Policy ID: 0
VXLAN Network Identifier (VNI): 50901 <-- L3VNI value
Type: IPv4 (0x0800) <-- IPv4 inner packet
Internet Protocol Version 4, Src: 10.1.101.11, Dst: 226.1.1.1 <-- Encapsulated IPv4 TRM group
0100 .... = Version: 4
Time to live: 254
Protocol: ICMP (1)
(multiple lines removed from this example capture)
### IPv6 ###
Leaf-02#sh mon capture 1 buffer detailed
Ethernet II, Src: 7c:21:0d:bd:2c:d6 (7c:21:0d:bd:2c:d6), Dst: 01:00:5e:01:01:01 (01:00:5e:01:01:01) <-- DMAC is matching 239.1.1.1
Type: IPv4 (0x0800) <-- IPv4 outer packet
Internet Protocol Version 4, Src: 172.16.254.3, Dst: 239.1.1.1
0100 .... = Version: 4
.... 0101 = Header Length: 20 bytes (5)
Differentiated Services Field: 0x00 (DSCP: CS0, ECN: Not-ECT)
0000 00.. = Differentiated Services Codepoint: Default (0)
.... ..00 = Explicit Congestion Notification: Not ECN-Capable Transport (0)
Total Length: 150
Identification: 0x4e4b (20043)
Flags: 0x4000, Don't fragment
0... .... .... .... = Reserved bit: Not set
.1.. .... .... .... = Don't fragment: Set <-- DF flag=1. MTU can be an issue if too low in path
..0. .... .... .... = More fragments: Not set
...0 0000 0000 0000 = Fragment offset: 0
Time to live: 253
Protocol: UDP (17)
Header checksum: 0x94f4 [validation disabled]
[Header checksum status: Unverified]
Source: 172.16.254.3
Destination: 239.1.1.1
User Datagram Protocol, Src Port: 65418, Dst Port: 4789 <-- VxLAN UDP port 4789
Source Port: 65418
Destination Port: 4789
<...snip...>
Virtual eXtensible Local Area Network
Flags: 0x0800, VXLAN Network ID (VNI)
0... .... .... .... = GBP Extension: Not defined
.... .... .0.. .... = Don't Learn: False
.... 1... .... .... = VXLAN Network ID (VNI): True
.... .... .... 0... = Policy Applied: False
.000 .000 0.00 .000 = Reserved(R): 0x0000
Group Policy ID: 0
VXLAN Network Identifier (VNI): 50901 <-- L3VNID 50901
Reserved: 0
Ethernet II, Src: 10:b3:d5:6a:00:00 (10:b3:d5:6a:00:00), Dst: 33:33:00:00:00:01 (33:33:00:00:00:01) <-- DMAC matches ff06:1::1
Type: IPv6 (0x86dd) <-- IPv6 inner packet
Internet Protocol Version 6, Src: fc00:1:101::11, Dst: ff06:1::1 <-- Encapsulated IPv6 TRM group
0110 .... = Version: 6
<...snip...>
Source: fc00:1:101::11
Destination: ff06:1::1
Internet Control Message Protocol v6
Type: Echo (ping) request (128)
<...snip...>
Situación 2: PIM SSM en el fabric
En este modo no hay RP en la superposición y no se utiliza MVPN de tipo 5 o 7 (la superposición sigue funcionando como PIM ASM). En SSM, el receptor envía e IGMPv3 S,G se une hacia LHR VTEP. Este VTEP realiza una búsqueda RPF para el Origen en el RIB. Si L3VNI SVI se encuentra como la interfaz RPF, LHR VTEP envía MVPN RT-7 al FHR VTEP que recibe e instala esta ruta. FHR VTEP luego informa a PIM que agregue L3VNI SVI como la interfaz saliente para la ruta multicast S,G.
En esta sección se muestran las diferencias con respecto a la situación 1. Los pasos y métodos que son iguales se indican sólo en la situación 1.
- Consulte los pasos de verificación y depuración para BGP y PIM del escenario 1, ya que las operaciones BGP y PIM son las mismas
Diagrama de la red
Para este modo, considere estos tipos de ruta BGP y sus orígenes
Creado por: Fuente VTEP
- EVPN Route-type 2. Se utiliza para obtener información de unidifusión y VRI para el origen y se agrega a la ruta C-Multicast (tipo MVPN-7) cuando VTEP se une al árbol STP.
Creado por: Receptor VTEP
- MVPN Route-type 7. La información de la capa IGMP o MLD y de EVPN Tipo-2 se utiliza para crear esta unión de tipo BGP. El Tipo-7 impulsa la creación del MRIB OIF en el lado de Origen.
Requisitos de EVPN tipo 2:
- FHR (VTEP de origen) verifica la adyacencia ARP (o ND) y CEF (confirma que la fuente está conectada directamente).
- FHR origina la actualización de EVPN de tipo 2 BGP
Requisitos de MVPN de tipo 7:
- Hay una entrada EVPN de tipo 2 (necesaria para construir la ruta C-Multicast de tipo 7 con VRI correcto y enviada desde VTEP de origen)
- VTEP del receptor: el informe de afiliación específico de la fuente IGMPv3 ha sido recibido y procesado por el LHR VTEP
- La interfaz LHR VTEP RPF es la interfaz Fabric L3VNI
Para este modo, se requiere una configuración adicional en LHR VTEP para habilitar el rango SSM y procesar los informes de afiliación de IGMPv3
Configuración de Leaf-03: establezca el solicitante IGMP en la versión 3 bajo la SVI del arrendatario
interface Vlan102
vrf forwarding green
ip address 10.1.102.1 255.255.255.0
ip pim sparse-mode
ip igmp version 3 <-- Sets the version to V3
end
Verify Leaf-03: el solicitante IGMP está configurado en la versión 3
Leaf-03#sh ip igmp snooping querier vlan 102
IP address : 10.1.102.1 <-- IP is that of the Vlan102 SVI
IGMP version : v3 <-- Querier is now version 3
Port : Router <-- Mrouter port is "Router" meaning querier is local to this VTEP
Max response time : 10s
Query interval : 60s
Robustness variable : 2
Enable Leaf-03: el rango SSM requerido para el VRF de arrendatario
Leaf-03(config)#ip pim vrf green ssm ?
default Use 232/8 group range for SSM <-- Set to the normally defined SSM range
range ACL for group range to be used for SSM <-- use an ACL to define a non-default SSM range
Verificar la secuencia de eventos requerida para este escenario
Paso 0 EVPN (Leaf-03): Verifique que haya un prefijo EVPN que BGP pueda encontrar el VRI para utilizar en el tipo-7 de MVPN.
Leaf-03#sh bgp l2vpn evpn all
BGP table version is 16, local router ID is 172.16.255.6
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
r RIB-failure, S Stale, m multipath, b backup-path, f RT-Filter,
x best-external, a additional-path, c RIB-compressed,
t secondary path, L long-lived-stale,
Origin codes: i - IGP, e - EGP, ? - incomplete
RPKI validation codes: V valid, I invalid, N Not found
Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 1:1 (default for vrf green)
* i [2][172.16.254.3:101][0][48][F4CFE24334C1][32][10.1.101.11]/24
172.16.254.3 0 100 0 ?
*>i 172.16.254.3 0 100 0 ? <-- From Leaf-01
Leaf-03#sh bgp l2vpn evpn all route-type 2 0 F4CFE24334C1 10.1.101.11 <-- Detailed view of the EVPN type-2 entry
BGP routing table entry for [2][172.16.254.3:101][0][48][F4CFE24334C1][32][10.1.101.11]/24, version 283
Paths: (2 available, best #2, table EVPN-BGP-Table)
Not advertised to any peer
Refresh Epoch 1
Local
172.16.254.3 (metric 3) (via default) from 172.16.255.1 (172.16.255.1)
Origin incomplete, metric 0, localpref 100, valid, internal, best
EVPN ESI: 00000000000000000000, Gateway Address: 0.0.0.0, VNI Label 50901, MPLS VPN Label 0
Extended Community: RT:1:1 MVPN AS:65001:0.0.0.0
MVPN VRF:172.16.255.3:4 ENCAP:8 Router MAC:10B3.D56A.8FC8 <-- BGP finds the VRI in this entry
Originator: 172.16.255.3, Cluster list: 172.16.255.1
rx pathid: 0, tx pathid: 0x0
Updated on May 6 2021 16:17:06 UTC
Paso 1 (hoja 03): informe de afiliación a IGMPv3 recibido y que contiene un origen
Leaf-03#show ip igmp snooping groups vlan 102 226.1.1.1
Vlan Group Type Version Port List
-----------------------------------------------------------------------
102 226.1.1.1 igmp v3 Gi1/0/10
Leaf-03#show ip igmp snooping groups vlan 102 226.1.1.1 sources <-- Specify "sources" to see Source information
Vlan Group Type Version Port List
-----------------------------------------------------------------------
Source information for group 226.1.1.1:
Timers: Expired sources are deleted on next IGMP General Query
SourceIP Expires Uptime Inc Hosts Exc Hosts
-------------------------------------------------------
10.1.101.11 00:01:20 00:02:58 1 0 <-- Source specified in IGMP includes one source
Paso 2 (hoja 03): BGP es informado de esta unión, crea y envía la unión MVPN de tipo 7.
debug mvpn
debug ip igmp vrf green 226.1.1.1
May 6 17:11:08.500: IGMP(6): Received v3 Report for 1 group on Vlan102 from 10.1.102.12
May 6 17:11:08.500: IGMP(6): Received Group record for group 226.1.1.1, mode 5 from 10.1.102.12 for 1 sources <-- IGMPv3 type join
May 6 17:11:08.500: IGMP(6): WAVL Insert group: 226.1.1.1 interface: Vlan102 Successful
May 6 17:11:08.500: IGMP(6): Create source 10.1.101.11
May 6 17:11:08.500: IGMP(6): Updating expiration time on (10.1.101.11,226.1.1.1) to 180 secs
May 6 17:11:08.500: IGMP(6): Setting source flags 4 on (10.1.101.11,226.1.1.1)
May 6 17:11:08.500: IGMP(6): MRT Add/Update Vlan102 for (10.1.101.11,226.1.1.1) by 0
May 6 17:11:08.501: MVPN: Received local route update for (10.1.101.11, 226.1.1.1) with RD: 1:1, Route Type: 7, flags: 0x00 <-- MVPN process gets updated
May 6 17:11:08.501: MVPN: Route Type 7 added [(10.1.101.11, 226.1.1.1)] rd:1:1 send:1
May 6 17:11:08.501: MVPN: Sending BGP prefix=[7:0 1:1 : (10.1.101.11,226.1.1.1)] len=23, nh 172.16.254.3, Originate route
May 6 17:11:08.501: MVPN: Originate C-route, BGP remote RD 1:1 <-- MVPN Sends the type-7 join to Source leaf
Leaf-03#sh bgp ipv4 mvpn all
BGP table version is 10, local router ID is 172.16.255.6
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
r RIB-failure, S Stale, m multipath, b backup-path, f RT-Filter,
x best-external, a additional-path, c RIB-compressed,
t secondary path, L long-lived-stale,
Origin codes: i - IGP, e - EGP, ? - incomplete
RPKI validation codes: V valid, I invalid, N Not found
Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 1:1 (default for vrf green)
*> [7][1:1][65001][10.1.101.11/32][226.1.1.1/32]/22 <-- Locally created Type-7
0.0.0.0 32768 ?
Leaf-03#sh ip mroute vrf green 226.1.1.1 <-- for SSM you only see S,G and no *,G
IP Multicast Routing Table
<...snip...>
(10.1.101.11, 226.1.1.1), 00:29:12/00:02:46, flags: sTIg <-- s = SSM, I = Source Specific Join received, g = Sent BGP C-Mroute
Incoming interface: Vlan901, RPF nbr 172.16.254.3 <-- RPF interface is the L3VNI
Outgoing interface list:
Vlan102, Forward/Sparse, 00:29:12/00:02:46
Paso 3 (Hoja-01): Hoja de Origen recibe e instala la ruta de unión MVPN Tipo-7 e informa a PIM que instale L3VNI OIF
debug mvpn
debug ip pim vrf green 226.1.1.1
May 6 18:16:07.260: MVPN: Received BGP prefix=[7:65001 1:1 : (10.1.101.11,226.1.1.1)] len=23, nexthop: 172.16.255.6, router-id: 172.16.255.1, Accept route <-- Receive and accept type-7
May 6 18:16:07.260: MVPN: Received BGP route update for (10.1.101.11, 226.1.1.1) with RD: 1:1, Route Type: 7, flags: 0x01
May 6 18:16:07.260: MVPN: Route Type 7 added [(10.1.101.11, 226.1.1.1), nh 172.16.255.6] rd:1:1 send:0, to us <-- add type-7 route
May 6 18:16:07.260: PIM(4)[green]: Join-list: (10.1.101.11/32, 226.1.1.1), S-bit set, BGP C-Route
May 6 18:16:07.263: PIM(4)[green]: Add Vlan901/0.0.0.0 to (10.1.101.11, 226.1.1.1), Forward state, by BGP SG Join <-- PIM adds Vlan901 L3VNI ad OIF based on BGP join
May 6 18:16:07.264: PIM(4)[green]: Insert (10.1.101.11,226.1.1.1) join in nbr 10.1.101.11's queue
May 6 18:16:07.264: MVPN(green[AF_IPv4]): Add (10.1.101.11, 226.1.1.1) intf Vlan901 olist Join state for BGP C-Rt type 7 Accept <-- MVPN add Vlan901 OIF from type-7
Leaf-01#sh bgp ipv4 mvpn all
<...snip...>
Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 1:1 (default for vrf green)
*>i [7][1:1][65001][10.1.101.11/32][226.1.1.1/32]/22
172.16.255.6 0 100 0 ? <-- Recieved from Reciever Leaf-03
* i 172.16.255.6 0 100 0 ?
Leaf-01#sh ip mroute vrf green 226.1.1.1
<...snip...>
(10.1.101.11, 226.1.1.1), 00:42:41/stopped, flags: sTGx <-- s = SSM Group, G = Received BGP C-Mroute
Incoming interface: Vlan101, RPF nbr 10.1.101.11
Outgoing interface list:
Vlan901, Forward/Sparse, 00:42:41/stopped <-- L3VNI installed as OIF interface
Paso 4 y 5 (Leaf-01 y Leaf-03): la multidifusión llega a la hoja de FHR y se envía a través del fabric a la hoja de LHR. Resumen de los comandos de validación que se proporciona aquí. Puede comprobar la validación detallada de estos comandos en el escenario 1.
show ip mroute vrf green 226.1.1.1 count <-- software mroute counters
show ip mfib vrf green 226.1.1.1<-- hardware mroute details & counters
sh platform software fed switch active ip mfib vrf green 226.1.1.1/32 10.1.101.11 detail <-- ASIC entry details and counters
Situación 3: RP único dentro del fabric (modo disperso normal)
Este modo se denomina indistintamente RP no Anycast o RP externo. En este modo, sólo hay un RP en la superposición. Por lo tanto, el árbol (*,G) de la superposición podría abarcar varios sitios. BGP utiliza un MVPN RT-6 para anunciar la pertenencia (*,G) a través del entramado. Si RP y FHR se encuentran en sitios diferentes, los registros PIM se envían a través del fabric. Este es el modo operativo predeterminado para PIM SM en la superposición.
Diagrama de la red
Para este modo, considere estos tipos de ruta BGP y sus orígenes
Creado por: Fuente VTEP
- EVPN Route-type 2. Se utiliza para obtener información de unidifusión y VRI para el origen y se agrega a la ruta C-Multicast (tipo MVPN-7) cuando VTEP se une al árbol STP.
- MVPN Route-type 5. Ruta A-D de origen enviada a VTEP para S,G
Creado por: RP VTEP
- EVPN Route-type 5. Se utiliza para obtener información de unidifusión y VRI para el loopback RP. El loopback no crea el tipo de ruta 2, por lo que se utiliza el tipo 5.
- MVPN Route-type 7. Se trata de los detalles de IGMP join + RT VRI tomados del EVPN Tipo-2 y enviados al VTEP de origen, e impulsa la creación del MRIB OIF.
Creado por: Receptor VTEP
- MVPN Route-type 6. Tipo de ruta creado por el receptor VTEP para unir el árbol compartido *,G (árbol RPT) hacia el RP.
- MVPN Route-type 7. La información de la capa IGMP o MLD y de EVPN Tipo-2 se utiliza para crear esta unión de tipo BGP. El Tipo-7 impulsa la creación del MRIB OIF en el lado de Origen.
Requisitos de EVPN tipo 2:
- FHR (VTEP de origen) verifica la adyacencia ARP (o ND) y CEF (confirma que la fuente está conectada directamente).
- FHR origina la actualización de EVPN de tipo 2 BGP
Requisitos de EVPN tipo 5:
- El loopback RP se configura y anuncia en BGP
Requisitos de MVPN de tipo 5:
En este modo, Leaf en el sitio de origen anuncia los mensajes A-D activos de origen para un (S,G) solo si se cumplen estas dos condiciones.
- Recibe tráfico en la interfaz RPF hacia el Origen. (el origen se envía mcast al FHR)
- La interfaz L3VNI SVI se agrega como una interfaz de reenvío para la entrada (S,G), como resultado de una unión S,G del RP como parte del proceso de registro PIM. (El L3VNI SVI se instala en la lista de la OIF)
Requisitos de MVPN de tipo 6:
- RP anunció su ruta EVPN Tipo-5 que contiene sus detalles de alcance VRI y Unicast.
- Unión IGMP recibida en LHR que activa una actualización BGP hacia RP
Requisitos de MVPN de tipo 7:
- Hay una entrada EVPN de tipo 2 (necesaria para construir la ruta C-Multicast de tipo 7 con VRI correcto y enviada desde VTEP de origen)
- Hay una entrada de tipo 5 de MVPN (necesaria para resolver qué par de origen/grupo está disponible para la unión STP)
- VTEP del receptor: el informe de afiliación a IGMP ha sido recibido y procesado por LHR VTEP
- RP VTEP: RP ha recibido paquetes de registro multicast, tiene rutas EVPN y tiene un receptor para S,G (aprendido a través del tipo-6)
- La interfaz LHR VTEP RPF es la interfaz Fabric L3VNI
Verificar la secuencia de eventos requerida para este escenario
Valide los pasos necesarios para que el VTEP receptor se una inicialmente al árbol compartido y, a continuación, pase al árbol de ruta más corta. Esto implica comprobaciones de las tablas BGP, los estados de creación IGMP y MRIB.
Paso EVPN (hoja 03): EVPN tipo 5 de RP se aprende en LHR. Esto es necesario para que el VTEP receptor cree una ruta MVPN de tipo 6
Leaf-03#sh bgp l2vpn evpn all route-type 5 0 10.2.255.255 32
...or you can also use:
Leaf-03#sh bgp l2vpn evpn detail [5][1:1][0][32][10.2.255.255]/17
BGP routing table entry for [5][1:1][0][32][10.2.255.255]/17, version 25
Paths: (2 available, best #1, table EVPN-BGP-Table)
Not advertised to any peer
Refresh Epoch 2
Local
172.16.254.4 (metric 3) (via default) from 172.16.255.1 (172.16.255.1) <-- RP's global next hop IP
Origin incomplete, metric 0, localpref 100, valid, internal, best
EVPN ESI: 00000000000000000000, Gateway Address: 0.0.0.0, VNI Label 50901, MPLS VPN Label 0
Extended Community: RT:1:1 MVPN AS:65001:0.0.0.0
MVPN VRF:172.16.255.4:2 ENCAP:8 Router MAC:7C21.0DBD.9548
Originator: 172.16.255.4, Cluster list: 172.16.255.1
rx pathid: 0, tx pathid: 0x0
Updated on Jan 13 2021 19:09:31 UTC
Refresh Epoch 2
Local
MVPN VRF:172.16.255.4:2 <-- MVPN VRI
Router MAC:7C21.0DBD.9548 <-- Leaf-02 RMAC
Paso 1 (Hoja-03): informe de afiliación a IGMP recibido
Leaf-03#sh ip igmp snooping groups
Vlan Group Type Version Port List
-----------------------------------------------------------------------
102 224.0.1.40 igmp v2 Gi1/0/10
102 226.1.1.1 igmp v2 Gi1/0/10 <-- Client has joined
Paso 2 (hoja 03): creación de MVPN de tipo 6, envío a RP y recepción por RP (hoja 02)
#### Type-6 from the Receiver VTEP perspective ###
Leaf-03#sh bgp ipv4 mvpn all route-type 6 1:1 65001 10.2.255.255 226.1.1.1 <-- Source is RP Loopback
...or you can also use:
Leaf-03#sh bgp ipv4 mvpn detail [6][1:1][65001][10.2.255.255/32][226.1.1.1/32]/22
BGP routing table entry for [6][1:1][65001][10.2.255.255/32][226.1.1.1/32]/22, version 13
Paths: (1 available, best #1, table MVPNv4-BGP-Table)
Advertised to update-groups:
1
Refresh Epoch 1
Local
0.0.0.0 from 0.0.0.0 (172.16.255.6) <-- Generated locally
Origin incomplete, localpref 100, weight 32768, valid, sourced, local, best
Extended Community: RT:172.16.255.4:2 <-- VRI Ext Comm added from EVPN Type-5
rx pathid: 2, tx pathid: 0x0
Updated on Jan 14 2021 14:51:29 UTC
#### Type-6 from the RP perspective ###
Leaf-02#sh bgp ipv4 mvpn all route-type 6 1:1 65001 10.2.255.255 226.1.1.1 <-- type-6, RD 1:1, AS 65001, Source/Group
...or you can also use:
Leaf-02#sh bgp ipv4 mvpn detail [6][1:1][65001][10.2.255.255/32][226.1.1.1/32]/22
BGP routing table entry for [6][1:1][65001][10.2.255.255/32][226.1.1.1/32]/22, version 25
Paths: (2 available, best #1, table MVPNv4-BGP-Table)
Flag: 0x100
Not advertised to any peer
Refresh Epoch 2
Local
172.16.255.6 (metric 3) from 172.16.255.1 (172.16.255.1)
Origin incomplete, metric 0, localpref 100, valid, internal, best
Extended Community: RT:172.16.255.4:2 <-- Contains VRI learned from EVPN Type-5
Originator: 172.16.255.6, Cluster list: 172.16.255.1 <-- Sent from Leaf03 IP to RP
rx pathid: 0, tx pathid: 0x0
Updated on Jan 14 2021 14:54:29 UTC
Depuraciones de los pasos 1 y 2 (hoja 01): informe IGMP, búsqueda de origen EVPN y creación de MVPN de tipo 6
debug ip igmp vrf green 226.1.1.1
debug bgp ipv4 mvpn updates
debug bgp ipv4 mvpn updates events
### Client sends IGMP membership report ###
### IGMP processes this IGMP report ###
*Feb 1 21:13:19.029: IGMP(2): Received v2 Report on Vlan102 from 10.1.102.12 for 226.1.1.1 <--- IGMP processes received report
*Feb 1 21:13:19.029: IGMP(2): Received Group record for group 226.1.1.1, mode 2 from 10.1.102.12 for 0 sources
*Feb 1 21:13:19.029: IGMP(2): WAVL Insert group: 226.1.1.1 interface: Vlan102 Successful
*Feb 1 21:13:19.029: IGMP(2): Switching to EXCLUDE mode for 226.1.1.1 on Vlan102
*Feb 1 21:13:19.029: IGMP(2): Updating EXCLUDE group timer for 226.1.1.1
*Feb 1 21:13:19.029: IGMP(2): MRT Add/Update Vlan102 for (*,226.1.1.1) by 0 <--- Notify MRT to add Vlan 102 into Outgoing interface list
### BGP is informed by IGMP, does an EVPN source lookup, creates the MVPN Type-6 route, sends to RR ###
(Without the EVPN Type-5 prefix already in BGP you see IGMP debugs trigger, but no subsequent BGP debugs as seen here)
*Feb 1 21:13:19.033: BGP[15] MVPN: add c-route, type 6, bs len 0 asn=0, rd=1:1, <-- Start creation of Type-6 C-multicast Shared Tree Join
*Feb 1 21:13:19.033: source=10.2.255.255/4, <-- RP loopback255
*Feb 1 21:13:19.033: group=226.1.1.1/4, <-- Group IP
*Feb 1 21:13:19.033: nexthop=172.16.254.4, <-- Global Next-Hop learned from EVPN VRI
*Feb 1 21:13:19.033: len left = 0
*Feb 1 21:13:19.033: BGP[14] MVPN umh lookup: vrfid 2, source 10.2.255.255 <-- UMH (upstream multicast hop) as found in the RT of the EVPN type-5
*Feb 1 21:13:19.033: BGP[4] MVPN umh lookup: vrfid 2, source 10.2.255.255, net 1:1:10.2.255.255/32, 1:1:10.2.255.255/32 with matching nexthop 172.16.254.4, remote-rd [1:1]: 0x9:65001:0.0.0.0, 0x10B:172.16.255.4:2, <-- EVPN info adding to MVPN
*Feb 1 21:13:19.033: BGP: MVPN(15) create local route [6][1:1][65001][10.2.255.255/32][226.1.1.1/32]/22 <--- MVPN creating type-6
*Feb 1 21:13:19.033: BGP[15] MVPN: add c-route, type 6, bs len 0 asn=65001, rd=1:1,
*Feb 1 21:13:19.033: source=10.2.255.255/4,
*Feb 1 21:13:19.033: group=226.1.1.1/4,
*Feb 1 21:13:19.033: nexthop=172.16.254.4,
*Feb 1 21:13:19.033: len left = 0
*Feb 1 21:13:19.033: BGP[14] MVPN umh lookup: vrfid 2, source 10.2.255.255
*Feb 1 21:13:19.033: BGP[4] MVPN umh lookup: vrfid 2, source 10.2.255.255, net 1:1:10.2.255.255/32, 1:1:10.2.255.255/32 with matching nexthop 172.16.254.4, remote-rd [1:1]: 0x9:65001:0.0.0.0, 0x10B:172.16.255.4:2,
*Feb 1 21:13:19.034: BGP(15): skip vrf default table RIB route [6][1:1][65001][10.2.255.255/32][226.1.1.1/32]/22
*Feb 1 21:13:19.034: BGP(15): 172.16.255.1 NEXT_HOP self is set for sourced RT Filter for net [6][1:1][65001][10.2.255.255/32][226.1.1.1/32]/22
*Feb 1 21:13:19.034: BGP(15): (base) 172.16.255.1 send UPDATE (format) [6][1:1][65001][10.2.255.255/32][226.1.1.1/32]/22, next 172.16.255.6, metric 0, path Local, extended community RT:172.16.255.4:2 <-- Advertise to RR (172.16.255.1)
Paso 3 y 4 (hoja 01):Desde la perspectiva de FHR, valide los eventos de creación y registro de S,G (los eventos de creación y registro de S,G se producen casi al mismo tiempo)
3. Se inicia el tráfico de datos y se crea S,G en FHR VTEP. Los requisitos indicados en la sección "Fuentes de multidifusión no detectadas" se aplican aquí.
4. Leaf-01 realiza el registro de origen al RP a través de su túnel PIM
Leaf-01#debug ip pim vrf green 226.1.1.1
PIM debugging is on
Leaf-01#debug ip mrouting vrf green 226.1.1.1
IP multicast routing debugging is on
### Debugs for PIM and Mroute show creation of S,G and PIM register encap event ###
*Jan 29 18:18:37.602: PIM(2): Building Periodic (*,G) Join / (S,G,RP-bit) Prune message for 226.1.1.1
*Jan 29 18:18:58.426: MRT(2): (10.1.101.11,226.1.1.1), RPF install from /0.0.0.0 to Vlan101/10.1.101.11<-- S,G is creation message (MRT process)
*Jan 29 18:18:58.427: PIM(2): Adding register encap tunnel (Tunnel4) as forwarding interface of (10.1.101.11, 226.1.1.1). <-- Sending via register (PIM process)
*Jan 29 18:18:58.427: MRT(2): Set the F-flag for (*, 226.1.1.1)
*Jan 29 18:18:58.427: MRT(2): Set the F-flag for (10.1.101.11, 226.1.1.1)
*Jan 29 18:18:58.428: MRT(2): Create (10.1.101.11,226.1.1.1), RPF (Vlan101, 10.1.101.11, 0/0) <-- S,G is creation message (MRT process)
*Jan 29 18:18:58.428: MRT(2): Set the T-flag for (10.1.101.11, 226.1.1.1)
### Tunnel 4 is PIM Register tunnel (Encap: encapsulate in tunnel to RP) ####
Leaf-01#sh int tunnel4
Tunnel4 is up, line protocol is up
Hardware is Tunnel
Description: Pim Register Tunnel (Encap) for RP 10.2.255.255 on VRF green <-- VRF green for Leaf-02 RP
Interface is unnumbered. Using address of Loopback901 (10.1.255.1) <-- Local Loopback
### S,G is created when Source sends data traffic ###
Leaf-01#sh ip mroute vrf green 226.1.1.1
IP Multicast Routing Table
<...snip...>
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(*, 226.1.1.1), 00:00:16/stopped, RP 10.2.255.255, flags: SPF
Incoming interface: Vlan901, RPF nbr 172.16.254.4
Outgoing interface list: Null
(10.1.101.11, 226.1.1.1), 00:00:16/00:02:47, flags: FTGqx
Incoming interface: Vlan101, RPF nbr 10.1.101.11, Registering <-- S,G created, in Register state, RPF IP is the /32 host prefix for this source
Outgoing interface list:
Vlan901, Forward/Sparse, 00:00:16/00:02:43 <-- OIF is the L3VNI SVI
#### Checking S,G in Hardware ###
Leaf-01#sh platform software fed switch active ip mfib vrf green 226.1.1.1/32 10.1.101.11 de
MROUTE ENTRY vrf 2 (10.1.101.11, 226.1.1.1/32) <-- VRF 2 is the ID for vrf green
HW Handle: 140213987784872 Flags: {Svl}
RPF interface: Vlan101(59)): SVI <-- RPF is Direct connected on a Local Subnet
HW Handle:140213987784872 Flags:A
Number of OIF: 2
Flags: 0x4 Pkts : 336 <-- packets that used this adjacency (similar to mfib command, but shown at the FED layer)
OIF Details:
Vlan101 A <-- Accept interface is programmed correctly
Vlan901 F {Remote} <-- Forward interface is L3VNI SVI
(Adj: 0x5f ) <-- Validate this Adj
Htm: 0x7f861cf071b8 Si: 0x7f861cf04838 Di: 0x7f861cf097a8 Rep_ri: 0x7f861ceecb38
### Check ADJ 0x5f for next hop details ###
Leaf-01#sh platform software fed switch active ip adj
IPV4 Adj entries
dest if_name dst_mac si_hdl ri_hdl pd_flags adj_id Last-modified
---- ------- ------- ------ ------ -------- ----- ------------------------
239.1.1.1 nve1.VNI50901 4500.0000.0000 0x7f861ce659b8 0x7f861ce65b68 0x60 0x5f 2021/01/29 17:07:06.568
Dest = MDT default group 239.1.1.1
Outgoing Interface = Nve1 using L3 VNI 50901
Paso 4 (Hoja-02): Desde la perspectiva RP, confirme que el registro de origen alcanza el RP y se crea S,G.
### PIM debugs showing PIM register event ###
Leaf-02#debug ip pim vrf green 226.1.1.1
PIM debugging is on
*Jan 29 18:21:35.500: PIM(2): Building Periodic (*,G) Join / (S,G,RP-bit) Prune message for 226.1.1.1
*Jan 29 18:21:35.500: PIM: rp our address <-- Leaf-02 is the RP
*Jan 29 18:21:41.005: PIM(2): Received v2 Register on Vlan901 from 10.1.255.1 <--- IP of Lo901 on Leaf-01 sent register
*Jan 29 18:21:41.005: for 10.1.101.11, group 226.1.1.1
*Jan 29 18:21:41.006: PIM(2): Adding register decap tunnel (Tunnel4) as accepting interface of (10.1.101.11, 226.1.1.1).
*Jan 29 18:21:41.008: PIM(2): Upstream mode for (10.1.101.11, 226.1.1.1) changed from 1 to 2
### Tunnel 4 is PIM Register tunnel (decap) ####
Leaf-02#sh int tunnel 4
Tunnel4 is up, line protocol is up
Hardware is Tunnel
Description: Pim Register Tunnel (Decap) for RP 10.2.255.255 on VRF green <-- decap side of register tunnel
Interface is unnumbered. Using address of Loopback255 (10.2.255.255) <-- RP IP
### Mroute debugs show pim Register triggering S,G ###
Leaf-02#debug ip mrouting vrf green 226.1.1.1
IP multicast routing debugging is on
*Jan 29 20:44:31.483: MRT(2): (10.1.101.11,226.1.1.1), RPF install from /0.0.0.0 to Vlan901/172.16.254.3 <-- RPF is to Leaf-01
*Jan 29 20:44:31.485: MRT(2): Create (10.1.101.11,226.1.1.1), RPF (Vlan901, 172.16.254.3, 200/0) <-- Create the S,G
*Jan 29 20:44:33.458: MRT(2): Set the T-flag for (10.1.101.11, 226.1.1.1) <-- Set SPT bit for S,G
### S,G is created and traffic is now sent along the *,G shared tree ###
Leaf-02#sh ip mroute vrf green
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group,
G - Received BGP C-Mroute, g - Sent BGP C-Mroute,
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed,
Q - Received BGP S-A Route, q - Sent BGP S-A Route,
V - RD & Vector, v - Vector, p - PIM Joins on route,
x - VxLAN group, c - PFP-SA cache created entry,
* - determined by Assert, # - iif-starg configured on rpf intf,
e - encap-helper tunnel flag
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(*, 226.1.1.1), 00:05:49/stopped, RP 10.2.255.255, flags: SGx <-- Sparse, Received BGP C-Mroute
Incoming interface: Null, RPF nbr 0.0.0.0 <-- RP is us (Incoming Interface Null with 0.0.0.0 RPF)
Outgoing interface list:
Vlan901, Forward/Sparse, 00:05:49/stopped
(10.1.101.11, 226.1.1.1), 00:01:22/00:01:41, flags: PTXgx <-- Pruned, SPT bit, Sent BGP C-Mroute
Incoming interface: Vlan901, RPF nbr 172.16.254.3 <-- Leaf-01 is RPF next hop
Outgoing interface list: Null
Paso 5 (Hoja-02): RP tiene un receptor, por lo que creó inmediatamente la ruta de unión al árbol de origen de MVPN de tipo 7
Leaf-02#sh ip mroute vrf green 226.1.1.1
<...snip...>
(*, 226.1.1.1), 00:02:22/00:00:37, RP 10.2.255.255, flags: SGx
Incoming interface: Null, RPF nbr 0.0.0.0
Outgoing interface list:
Vlan901, Forward/Sparse, 00:02:22/00:00:37 <-- L3 VNI is populated from Receiver BGP Type-6 join
#### Debugs showing Type-7 creation from RP ####
Leaf-02#debug bgp ipv4 mvpn updates
BGP updates debugging is on for address family: MVPNv4 Unicast
Leaf-02#debug bgp ipv4 mvpn updates events
BGP update events debugging is on for address family: MVPNv4 Unicast
*Jan 29 18:21:41.008: BGP[15] MVPN: add c-route, type 7, bs len 0 asn=0, rd=1:1,
*Jan 29 18:21:41.008: source=10.1.101.11/4,
*Jan 29 18:21:41.008: group=226.1.1.1/4,
*Jan 29 18:21:41.008: nexthop=172.16.254.3, <-- Leaf-01 Global next hop
*Jan 29 18:21:41.008: len left = 0
*Jan 29 18:21:41.008: BGP[14] MVPN umh lookup: vrfid 2, source 10.1.101.11
*Jan 29 18:21:41.008: BGP[4] MVPN umh lookup: vrfid 2, source 10.1.101.11, net 1:1:10.1.101.11/32, 1:1:10.1.101.11/32 with matching nexthop 172.16.254.3, remote-rd [172.16.]: 0x9:65001:0.0.0.0, 0x10B:172.16.255.3:2, <-- This is the VRI picked up from the EVPN Type-2
*Jan 29 18:21:41.009: BGP: MVPN(15) create local route [7][172.16.254.3:101][65001][10.1.101.11/32][226.1.1.1/32]/22
*Jan 29 18:21:41.009: BGP[15] MVPN: add c-route, type 7, bs len 0 asn=65001, rd=1:1,
*Jan 29 18:21:41.009: source=10.1.101.11/4,
*Jan 29 18:21:41.009: group=226.1.1.1/4,
*Jan 29 18:21:41.009: nexthop=172.16.254.3,
*Jan 29 18:21:41.009: len left = 0
*Jan 29 18:21:41.009: BGP[14] MVPN umh lookup: vrfid 2, source 10.1.101.11
*Jan 29 18:21:41.009: BGP[4] MVPN umh lookup: vrfid 2, source 10.1.101.11, net 1:1:10.1.101.11/32, 1:1:10.1.101.11/32 with matching nexthop 172.16.254.3, remote-rd [172.16.]: 0x9:65001:0.0.0.0, 0x10B:172.16.255.3:2,
### Type-7 Locally created on RP and sent to Source Leaf-01 ###
Leaf-02#sh bgp ipv4 mvpn all
BGP table version is 81, local router ID is 172.16.255.4
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
r RIB-failure, S Stale, m multipath, b backup-path, f RT-Filter,
x best-external, a additional-path, c RIB-compressed,
t secondary path, L long-lived-stale,
Origin codes: i - IGP, e - EGP, ? - incomplete
RPKI validation codes: V valid, I invalid, N Not found
Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 172.16.254.3:101 <-- Note the VRI is learnt from Leaf-01
*> [7][172.16.254.3:101][65001][10.1.101.11/32][226.1.1.1/32]/22 <-- [7] = type-7 for this S,G / VRI 172.16.254.3:101 learned from Leaf-01
0.0.0.0 32768 ? <-- 0.0.0.0 locally originated with local Weight
Paso 6 (Hoja-01): Hoja-01 de Origen recibe e instala MVPN Route-Type 7. (L3 VNI SVI se instala como una interfaz de reenvío para S,G)
### Received Type-7 from Leaf-02 RP ###
Leaf-01#debug bgp ipv4 mvpn updates
BGP updates debugging is on for address family: MVPNv4 Unicast
Leaf-01#debug bgp ipv4 mvpn updates events
BGP update events debugging is on for address family: MVPNv4 Unicast
*Jan 29 18:18:58.457: BGP(15): 172.16.255.1 rcvd UPDATE w/ attr: nexthop 172.16.255.4, origin ?, localpref 100, metric 0, originator 172.16.255.4, clusterlist 172.16.255.1, extended community RT:172.16.255.3:2 <-- Type-7 from Route Reflector 172.16.255.1
*Jan 29 18:18:58.457: BGP(15): 172.16.255.1 rcvd [7][172.16.254.3:101][65001][10.1.101.11/32][226.1.1.1/32]/22 <-- Received [7] Type-7 BGP join route
*Jan 29 18:18:58.457: BGP(15): skip vrf default table RIB route [7][172.16.254.3:101][65001][10.1.101.11/32][226.1.1.1/32]/22
*Jan 29 18:18:58.458: BGP(15): add RIB route (0:0)[7][1:1][65001][10.1.101.11/32][226.1.1.1/32]/22
### PIM updated by MVPN to install L3 VNI in Outgoing Interface List ###
Leaf-01#debug ip pim vrf green 226.1.1.1
PIM debugging is on
Leaf-01#debug ip mrouting vrf green 226.1.1.1
IP multicast routing debugging is on
*Jan 29 18:18:58.458: PIM(2): Join-list: (10.1.101.11/32, 226.1.1.1), S-bit set, BGP C-Route
*Jan 29 18:18:58.459: MRT(2): WAVL Insert VxLAN interface: Vlan901 in (10.1.101.11,226.1.1.1) Next-hop: 239.1.1.1 VNI 50901 Successful <-- VxLAN info such as VNI, and outer Mcast group during Olist creation
*Jan 29 18:18:58.459: MRT(2): set min mtu for (10.1.101.11, 226.1.1.1) 18010->9198
*Jan 29 18:18:58.460: MRT(2): Add Vlan901/239.1.1.1/50901 to the olist of (10.1.101.11, 226.1.1.1), Forward state - MAC not built <-- OIF is added for the VNI SVI 901
*Jan 29 18:18:58.460: PIM(2): Add Vlan901/0.0.0.0 to (10.1.101.11, 226.1.1.1), Forward state, by BGP SG Join
*Jan 29 18:18:58.460: MRT(2): Add Vlan901/239.1.1.1/50901to the olist of (10.1.101.11, 226.1.1.1), Forward state - MAC not built
Paso 7 (Hoja-01): Hoja-01 anuncia el origen MVPN A-D Tipo-5 para S,G
Leaf-01#debug bgp ipv4 mvpn updates
BGP updates debugging is on for address family: MVPNv4 Unicast
Leaf-01#debug bgp ipv4 mvpn updates events
BGP update events debugging is on for address family: MVPNv4 Unicast
*Jan 29 18:18:58.461: BGP(15): nettable_walker [5][1:1][10.1.101.11][226.1.1.1]/18 route sourced locally <-- BGP determines route is local to Leaf-01
*Jan 29 18:18:58.461: BGP(15): delete RIB route (0:0)[5][1:1][10.1.101.11][226.1.1.1]/18
*Jan 29 18:18:58.461: BGP(15): 172.16.255.1 NEXT_HOP self is set for sourced RT Filter for net [5][1:1][10.1.101.11][226.1.1.1]/18
*Jan 29 18:18:58.461: BGP(15): (base) 172.16.255.1 send UPDATE (format) [5][1:1][10.1.101.11][226.1.1.1]/18, next 172.16.255.3, metric 0, path Local, extended community RT:1:1 <-- Send Type-5 update
Paso 8 (hoja 03): VTEP receptor obtiene el tipo 5 e instala la ruta de origen A-D para S,G
Leaf-03#debug bgp ipv4 mvpn updates
BGP updates debugging is on for address family: MVPNv4 Unicast
Leaf-03#debug bgp ipv4 mvpn updates events
BGP update events debugging is on for address family: MVPNv4 Unicast
*Jan 29 19:18:53.318: BGP(15): 172.16.255.1 rcvd UPDATE w/ attr: nexthop 172.16.255.3, origin ?, localpref 100, metric 0, originator 172.16.255.3, clusterlist 172.16.255.1, community no-export, extended community RT:1:1
*Jan 29 19:18:53.319: BGP(15): 172.16.255.1 rcvd [5][1:1][10.1.101.11][226.1.1.1]/18 <-- Type-5 Received from Source VTEP Leaf-01
*Jan 29 19:18:53.319: BGP(15): skip vrf default table RIB route [5][1:1][10.1.101.11][226.1.1.1]/18
Leaf-03#sh bgp ipv4 mvpn all route-type 5 10.1.101.11 226.1.1.1
...or you can also use:
Leaf-03#sh bgp ipv4 mvpn detail [5][1:1][10.1.101.11][226.1.1.1]/18
BGP routing table entry for [5][1:1][10.1.101.11][226.1.1.1]/18, version 41 <-- Type-5 A-D route from Leaf-01
Paths: (2 available, best #2, table MVPNv4-BGP-Table, not advertised to EBGP peer)
Flag: 0x100
Not advertised to any peer
Refresh Epoch 1
Local
172.16.255.3 (metric 3) from 172.16.255.1 (172.16.255.1) <-- Leaf-01 IP
Origin incomplete, metric 0, localpref 100, valid, internal, best
Community: no-export
Extended Community: RT:1:1
Originator: 172.16.255.3, Cluster list: 172.16.255.1
rx pathid: 0, tx pathid: 0x0
Updated on Jan 29 2021 19:18:53 UTC
Paso 9 (hoja 03): se crea S,G, hoja 03 envía MVPN tipo 7 para unirse al árbol SPT y comienza a aceptar tráfico
debug ip mrouting vrf green 226.1.1.1
debug bgp ipv4 mvpn updates
debug bgp ipv4 mvpn updates events
### Debug of Mrouting shows S,G create and call to BGP to create Type-7 BGP S,G join ###
*Feb 12 19:34:26.045: MRT(2): (10.1.101.11,226.1.1.1), RPF install from /0.0.0.0 to Vlan901/172.16.254.3 <-- RPF check done as first operation. Selected L3VNI SVI and Leaf-01 next hop
*Feb 12 19:34:26.046: MRT(2): Create (10.1.101.11,226.1.1.1), RPF (Vlan901, 172.16.254.3, 200/0) <-- RPF successful Creating S,G
*Feb 12 19:34:26.047: MRT(2): WAVL Insert interface: Vlan102 in (10.1.101.11,226.1.1.1) Successful
*Feb 12 19:34:26.047: MRT(2): set min mtu for (10.1.101.11, 226.1.1.1) 18010->9198
*Feb 12 19:34:26.047: MRT(2): Set the T-flag for (10.1.101.11, 226.1.1.1)
*Feb 12 19:34:26.048: MRT(2): Add Vlan102/226.1.1.1 to the olist of (10.1.101.11, 226.1.1.1), Forward state - MAC not built <-- Adding Vlan102 Receiver SVI into OIF list
*Feb 12 19:34:26.048: MRT(2): Set BGP Src-Active for (10.1.101.11, 226.1.1.1) <-- Signaling to BGP that this Source is seen and join SPT path
### BGP Type-7 created ###
Leaf-03#sh bgp ipv4 mvpn all
Route Distinguisher: 172.16.254.3:101 <-- VRI Route Distinguisher
*> [7][172.16.254.3:101][65001][10.1.101.11/32][226.1.1.1/32]/22 <-- Type [7], VRI, S,G info
0.0.0.0 32768 ? <-- created locally
Leaf-03#sh ip mroute vrf green 226.1.1.1 10.1.101.11
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group,
G - Received BGP C-Mroute, g - Sent BGP C-Mroute,
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed,
Q - Received BGP S-A Route, q - Sent BGP S-A Route,
V - RD & Vector, v - Vector, p - PIM Joins on route,
x - VxLAN group, c - PFP-SA cache created entry,
* - determined by Assert, # - iif-starg configured on rpf intf,
e - encap-helper tunnel flag
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(10.1.101.11, 226.1.1.1), 00:08:41/00:02:13, flags: TgQ <-- SPT bit, Sent MVPN type-7, Received MVPN type-5
Incoming interface: Vlan901, RPF nbr 172.16.254.3 <-- Receive from L3VNI via Leaf-01 IP next hop
Outgoing interface list:
Vlan102, Forward/Sparse, 00:08:41/00:02:22 <-- Send to host in Vlan 102
Paso 10 (Hoja-01): Hoja-01 recibe e instala MVPN Tipo-7 desde Hoja-03
debug bgp ipv4 mvpn updates
debug bgp ipv4 mvpn updates events
### Type-7 Received from Leaf-03 VTEP and installed into RIB ###
*Feb 12 19:55:29.000: BGP(15): 172.16.255.1 rcvd [7][172.16.254.3:101][65001][10.1.101.11/32][226.1.1.1/32]/22 <-- Type-7 from Leaf-03
*Feb 12 19:55:29.000: BGP(15): skip vrf default table RIB route [7][172.16.254.3:101][65001][10.1.101.11/32][226.1.1.1/32]/22
*Feb 12 19:55:29.000: BGP(15): add RIB route (0:0)[7][1:1][65001][10.1.101.11/32][226.1.1.1/32]/22
Situación 4: RP fuera del fabric (RP importado desde el borde hoja-02 desde el espacio IP)
Este escenario es básicamente el mismo que el escenario 2. Hay un único RP utilizado por el fabric en general. La diferencia es que la IP de RP se debe importar desde un espacio IP no de fabric a Fabric y se debe anunciar en BGP.
En esta sección se muestran las diferencias con respecto al escenario 3. Los pasos y métodos que son iguales se indican sólo en la situación 3
- Consulte Verificación de la Secuencia de Eventos Requerida para este Escenario desde el Escenario 3 ya que las operaciones BGP y PIM son las mismas
Diagrama de la red
Verificar importaciones de switch de frontera de IP a Fabric
La diferencia principal con este diseño frente a la situación 3 es la necesidad de importar primero la IP RP desde el espacio IP a EVPN.
El borde debe contener ciertos comandos para importar/exportar desde y hacia el fabric y los espacios IP:
- route-target <value> comandos de costura en la sección de configuración VRF
- advertise l2vpn evpn under the BGP vrf address-family
Verificar (hoja 02): configuración
Leaf-02#sh run vrf green
Building configuration...
Current configuration : 1533 bytes
vrf definition green
rd 1:1
!
address-family ipv4
mdt auto-discovery vxlan
mdt default vxlan 239.1.1.1
mdt overlay use-bgp
route-target export 1:1
route-target import 1:1
route-target export 1:1 stitching <-- BGP-EVPN fabric redistributes the stitching routes between the EVPN and the IP BGP
route-target import 1:1 stitching
exit-address-family
Leaf-02#sh run | sec router bgp
address-family ipv4 vrf green <--- BGP VRF green address-family
advertise l2vpn evpn <--- Use the 'advertise l2vpn evpn' command and 'export stitching' RTs to push the native routes towards the EVPN
redistribute connected
redistribute static
redistribute ospf 2 match internal external 1 external 2 <-- Learning via external OSPF neighbor in VRF
exit-address-family
Verify (Leaf-02): Prefix Import and Advertisement
debug bgp vpnv4 unicast updates
debug bgp vpnv4 unicast updates events
debug bgp l2vpn evpn updates
debug bgp l2vpn evpn updates events
*Feb 15 15:30:54.407: BGP(4): redist event (1) request for 1:1:10.2.255.255/32 <-- VPNv4 Redistribute statement present in BGP address family
*Feb 15 15:30:54.407: BGP(4) route 1:1:10.2.255.255/32 gw-1 10.2.1.2 src_proto (ospf) path-limit 1
*Feb 15 15:30:54.407: BGP(4): route 1:1:10.2.255.255/32 up
*Feb 15 15:30:54.407: bgp_ipv4set_origin: redist 1, opaque 0x0, net 10.2.255.255
*Feb 15 15:30:54.407: BGP(4): sourced route for 1:1:10.2.255.255/32 path 0x7FF8065EB9C0 id 0 gw 10.2.1.2 created (weight 32768)
*Feb 15 15:30:54.408: BGP(4): redistributed route 1:1:10.2.255.255/32 added gw 10.2.1.2
*Feb 15 15:30:54.408: BGP: topo green:VPNv4 Unicast:base Remove_fwdroute for 1:1:10.2.255.255/32
*Feb 15 15:30:54.408: BGP(4): 1:1:10.2.255.255/32 import vpn re-orig or locally sourced or learnt from CE <-- Prefix learned from external CE
*Feb 15 15:30:54.409: BGP(10): update modified for [5][1:1][0][32][10.2.255.255]/17 <--- EVPN picked up and Type-5 creation
*Feb 15 15:30:54.409: BGP(10): 172.16.255.1 NEXT_HOP set to vxlan local vtep-ip 172.16.254.4 for net [5][1:1][0][32][10.2.255.255]/17 <-- Set NH to Leaf-02 loopback
*Feb 15 15:30:54.409: BGP(10): update modified for [5][1:1][0][32][10.2.255.255]/17
*Feb 15 15:30:54.409: BGP(10): (base) 172.16.255.1 send UPDATE (format) [5][1:1][0][32][10.2.255.255]/17, next 172.16.254.4, metric 2, path Local, extended community RT:1:1 OSPF DOMAIN ID:0x0005:0x000000020200 MVPN AS:65001:0.0.0.0 MVPN VRF:172.16.255.4:2 ENCAP:8 Router MAC:7C21.0DBD.9548 OSPF RT:0.0.0.0:2:0 OSPF ROUTER ID:10.2.255.255:0
<-- BGP EVPN Type update created from Non-fabric Imported prefix and sent to RR
### Verify the NLRI is learned and Imported on Border Leaf-02 ###
Leaf-02#sh bgp vpnv4 unicast all
BGP table version is 39, local router ID is 172.16.255.4
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
r RIB-failure, S Stale, m multipath, b backup-path, f RT-Filter,
x best-external, a additional-path, c RIB-compressed,
t secondary path, L long-lived-stale,
Origin codes: i - IGP, e - EGP, ? - incomplete
RPKI validation codes: V valid, I invalid, N Not found
Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 1:1 (default for vrf green)
AF-Private Import to Address-Family: L2VPN E-VPN, Pfx Count/Limit: 3/1000 <-- Prefix Import details. (Note default import limit of 1000)
*> 10.2.255.255/32 10.2.1.2 2 32768 ? <-- Locally redistributed, Next hop on CE device
Leaf-02#sh bgp l2vpn evpn all route-type 5 0 10.2.255.255 32
...or you can also use:
Leaf-02#sh bgp l2vpn evpn detail [5][1:1][0][32][10.2.255.255]/17
BGP routing table entry for [5][1:1][0][32][10.2.255.255]/17, version 69
Paths: (1 available, best #1, table EVPN-BGP-Table)
Advertised to update-groups:
2
Refresh Epoch 1
Local, imported path from base
10.2.1.2 (via vrf green) from 0.0.0.0 (172.16.255.4) <-- Imported to EVPN Fabric table from IP
Origin incomplete, metric 2, localpref 100, weight 32768, valid, external, best
EVPN ESI: 00000000000000000000, Gateway Address: 0.0.0.0, local vtep: 172.16.254.4, VNI Label 50901, MPLS VPN Label 17 <-- VTEP IP of Leaf-02, L3VNI label
Extended Community: RT:1:1 OSPF DOMAIN ID:0x0005:0x000000020200
MVPN AS:65001:0.0.0.0 MVPN VRF:172.16.255.4:2 ENCAP:8 <-- MVPN VRI created
Router MAC:7C21.0DBD.9548 OSPF RT:0.0.0.0:2:0
OSPF ROUTER ID:10.2.255.255:0
rx pathid: 0, tx pathid: 0x0
Updated on Feb 15 2021 15:30:54 UTC
Verify (Leaf-02): Border Path to RP
Leaf-02#sh ip mroute vrf green
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group,
G - Received BGP C-Mroute, g - Sent BGP C-Mroute,
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed,
Q - Received BGP S-A Route, q - Sent BGP S-A Route,
V - RD & Vector, v - Vector, p - PIM Joins on route,
x - VxLAN group, c - PFP-SA cache created entry,
* - determined by Assert, # - iif-starg configured on rpf intf,
e - encap-helper tunnel flag
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(*, 226.1.1.1), 2d21h/stopped, RP 10.2.255.255, flags: SJGx <-- *,G for group and Non-fabric RP IP
Incoming interface: Vlan2001, RPF nbr 10.2.1.2 <-- RPF neighbor is populated for IP next hop outside VxLAN
Outgoing interface list:
Vlan901, Forward/Sparse, 01:28:47/stopped <-- Outgoing is L3VNI SVI
Situación 5: MDT de datos
Verificar grupo de datos MDT
El grupo de datos de MDT es similar a su grupo predeterminado de MDT donde se encapsulará el grupo de túnel exterior para TRM. Sin embargo, a diferencia del valor predeterminado de MDT, este grupo solo tendrá VTEP que se unan a este árbol si tienen receptores interesados para el grupo TRM.
Configuración necesaria
vrf definition green
rd 1:1
!
address-family ipv4
mdt auto-discovery vxlan
mdt default vxlan 239.1.1.1
mdt data vxlan 239.1.2.0 0.0.0.255 <-- Defines MDT Data underlay group address range
mdt data threshold 1 <-- Defines the threshold before cutting over to the Data group (In Kilobits per second)
mdt overlay use-bgp spt-only
route-target export 1:1
route-target import 1:1
route-target export 1:1 stitching
route-target import 1:1 stitching
exit-address-family
!
Compruebe que el grupo MDT está correctamente programado en el lado de origen
- La interfaz entrante del grupo MDT es el loopback del lado de origen
- La interfaz saliente del grupo MDT es la interfaz subyacente
Verifique Leaf-01: la ruta multicast MDT es correcta en MRIB/MFIB
Leaf-01#sh ip mroute 239.1.2.0 172.16.254.3
<snip>
(172.16.254.3, 239.1.2.0), 00:01:19/00:02:10, flags: FT
Incoming interface: Loopback1, RPF nbr 0.0.0.0 <-- IIF is local loopback with 0.0.0.0 RPF indicating local
Outgoing interface list:
TenGigabitEthernet1/0/1, Forward/Sparse, 00:01:19/00:03:10 <-- OIF is the underlay uplink
Leaf-01#sh ip mfib 239.1.2.0 172.16.254.3
<snip>
(172.16.254.3,239.1.2.0) Flags: HW
SW Forwarding: 2/0/828/0, Other: 0/0/0
HW Forwarding: 450/2/834/13, Other: 0/0/0 <-- Hardware counters indicate the entry is operating in hardware and forwarding packets
Null0 Flags: A <-- Null0 (Originated locally)
TenGigabitEthernet1/0/1 Flags: F NS <-- OIF is into the Underlay (Global routing table)
Pkts: 0/0/0 Rate: 0 pps
Verify Leaf-01: Entradas FED para el grupo MDT
Leaf-01#show platform software fed switch active ip mfib 239.1.2.0/32 172.16.254.3 detail <-- The detail option gives summary of the HW indexes
MROUTE ENTRY vrf 0 (172.16.254.3, 239.1.2.0/32) <-- vrf 0 = global for this MDT Data S,G pair
HW Handle: 140028029798744 Flags:
RPF interface: Null0(1)): <-- Leaf-01 is the Source(Null0)
HW Handle:140028029798744 Flags:A
Number of OIF: 2
Flags: 0x4 Pkts : 570 <-- Packets that used this adjacency (similar to the mfib command, but shown at the FED layer)
OIF Details:
TenGigabitEthernet1/0/1 F NS <-- The Underlay Outgoing Interface and F-Forward flag is set
Null0 A <-- The Incoming Interface is local loopback1 and A-Accept flag set
Htm: 0x7f5ad0fa48b8 Si: 0x7f5ad0fa4258 Di: 0x7f5ad0fa8948 Rep_ri: 0x7f5ad0fa8e28 <--The DI (dest index) handle
DI details
----------
Handle:0x7f5ad0fa8948 Res-Type:ASIC_RSC_DI Res-Switch-Num:255 Asic-Num:255 Feature-ID:AL_FID_L3_MULTICAST_IPV4 Lkp-ftr-id:LKP_FEAT_INVALID ref_count:1
priv_ri/priv_si Handle:(nil) Hardware Indices/Handles: index0:0x536e mtu_index/l3u_ri_index0:0x0 index1:0x536e mtu_index/l3u_ri_index1:0x0 index2:0x536e mtu_index/l3u_ri_index2:0x0 index3:0x536e mtu_index/l3u_ri_index3:0x0
<snip>
Brief Resource Information (ASIC_INSTANCE# 3)
----------------------------------------
Destination index = 0x536e
pmap = 0x00000000 0x00000001
pmap_intf : [TenGigabitEthernet1/0/1] <--FED has the correct programing of the OIF
==============================================================
Compruebe que el grupo MDT está correctamente programado en el lado del receptor
- La interfaz entrante del grupo MDT es la interfaz RPF de vuelta al Loopback del lado de origen
- La interfaz saliente del grupo MDT es la interfaz de túnel Encap/Decap
Verifique Leaf-02: la ruta multicast MDT es correcta en MRIB/MFIB
Leaf-03#sh ip mroute 239.1.2.0 172.16.254.3 <-- This is the Global MDT Data Group
<snip>
(172.16.254.3, 239.1.2.0), 00:06:12/00:02:50, flags: JTx <-- Source is Leaf-01 Loopback1 IP
Incoming interface: TenGigabitEthernet1/0/1, RPF nbr 172.16.26.2
Outgoing interface list:
Tunnel0, Forward/Sparse, 00:06:12/00:02:47 <-- Decap Tunnel
Leaf-03#sh ip mfib 239.1.2.0 172.16.254.3
<snip>
Default <-- Global Routing Table
(172.16.254.3,239.1.2.0) Flags: HW
SW Forwarding: 2/0/828/0, Other: 0/0/0
HW Forwarding: 760/2/846/13, Other: 0/0/0 <-- Hardware counters indicate the entry is operating in hardware and forwarding packets
TenGigabitEthernet1/0/1 Flags: A <-- Accept via Underlay (Global) interface
Tunnel0, VXLAN Decap Flags: F NS <-- Forward to VxLAN Decap Tunnel
Pkts: 0/0/2 Rate: 0 pps
Verify Leaf-02: entradas FED para el grupo MDT
Leaf-03#show platform software fed switch active ip mfib 239.1.2.0/32 172.16.254.3 detail
MROUTE ENTRY vrf 0 (172.16.254.3, 239.1.2.0/32) <-- vrf 0 = global for this MDT Data S,G pair
HW Handle: 140592885196696 Flags:
RPF interface: TenGigabitEthernet1/0/1(55)): <-- RPF Interface to 172.16.254.3
HW Handle:140592885196696 Flags:A
Number of OIF: 2
Flags: 0x4 Pkts : 800 <-- packets that used this adjacency (similar to mfib command, but shown at the FED layer)
OIF Details:
TenGigabitEthernet1/0/1 A <-- Accept MDT packets from this interface
Tunnel0 F NS <-- Forward to Decap Tunnel to remove VxLAN header
(Adj: 0x3c ) <-- Tunnel0 Adjacency
Htm: 0x7fde54fb7d68 Si: 0x7fde54fb50d8 Di: 0x7fde54fb4948 Rep_ri: 0x7fde54fb4c58
<snip>
RI details <-- Rewrite Index is used for VxLAN decapsulation
----------
Handle:0x7fde54fb4c58 Res-Type:ASIC_RSC_RI_REP Res-Switch-Num:255 Asic-Num:255 Feature-ID:AL_FID_L3_MULTICAST_IPV4 Lkp-ftr-id:LKP_FEAT_INVALID ref_count:1
priv_ri/priv_si Handle:(nil) Hardware Indices/Handles: index0:0x1a mtu_index/l3u_ri_index0:0x0 index1:0x1a mtu_index/l3u_ri_index1:0x0 index2:0x1a mtu_index/l3u_ri_index2:0x0 index3:0x1a mtu_index/l3u_ri_index3:0x0
Brief Resource Information (ASIC_INSTANCE# 0)
----------------------------------------
ASIC# 0
Replication list :
------------------
Total #ri : 6
Start_ri : 26
Common_ret : 0
Replication entry rep_ri 0x1A #elem = 1
0) ri[0]=0xE803 Dynamic port=88ri_ref_count:1 dirty=0
<snip>
Leaf-03#show platfomr software fed switch active fwd-asic resource asic all rewrite-index range 0xE803 0XE803
ASIC#:0 RI:59395 Rewrite_type:AL_RRM_REWRITE_L2_PAYLOAD_IPV4_EVPN_DECAP(118) Mapped_rii:LVX_EVPN_DECAP(143)
<snip>
Debug MDT Data Group
Utilice el debug de MVPN para verificar el evento de transición de MDT de datos
VTEP del lado fuente
Leaf#debug mvpn
<snip>
*Mar 27 12:12:11.115: MVPN: Received local withdraw for (10.1.101.11, 239.1.1.1) with RD: 1:1, Route Type: 5, flags: 0x00
*Mar 27 12:12:11.115: MVPN: Sending BGP prefix=[5: 1:1 : (10.1.101.11,239.1.1.1)] len=19, nh 0.0.0.0, Withdraw route
*Mar 27 12:12:11.115: MVPN: Route Type 5 deleted [(10.1.101.11, 239.1.1.1), nh 0.0.0.0] rd:1:1 send:1
*Mar 27 12:12:11.115: MVPN: Received BGP prefix=[5: 1:1 : (10.1.101.11,239.1.1.1)] len=19, nexthop: UNKNOWN, router-id: 0.0.0.0, Withdraw route
*Mar 27 12:12:11.115: MVPN: Received BGP withdraw for (10.1.101.11, 239.1.1.1) with RD: 1:1, Route Type: 5, flags: 0x00
*Mar 27 12:13:00.430: MVPN: Received local route update for (10.1.101.11, 239.1.1.1) with RD: 1:1, Route Type: 5, flags: 0x00
*Mar 27 12:13:00.431: MVPN: Route Type 5 added [(10.1.101.11, 239.1.1.1), nh 0.0.0.0] rd:1:1 send:1
*Mar 27 12:13:00.431: MVPN: RP 10.2.255.255 updated in newly created route
*Mar 27 12:13:00.431: MVPN: Sending BGP prefix=[5: 1:1 : (10.1.101.11,239.1.1.1)] len=19, nh 0.0.0.0, Originate route
*Mar 27 12:13:00.431: MVPN: Received BGP prefix=[5: 1:1 : (10.1.101.11,239.1.1.1)] len=19, nexthop: UNKNOWN, router-id: 0.0.0.0, Withdraw route
*Mar 27 12:13:00.431: MVPN: Received BGP withdraw for (10.1.101.11, 239.1.1.1) with RD: 1:1, Route Type: 5, flags: 0x00
*Mar 27 12:13:17.151: MVPN(green[AF_IPv4]): Successfully notified nve fordatamdt adjacency create 239.1.2.0 <-- Notify NVE about creating DATA MDT
*Mar 27 12:13:17.151: MVPN: Received local update <104:0x00:0>(172.16.254.3, 239.1.2.0) next_hop:0.0.0.0 router_id:172.16.255.3 RD:[1:1] Rmt-RD:[1:1] route type:3 <-- Received local update for the data group
*Mar 27 12:13:17.151: MVPN: LSM AD route added [(10.1.101.11,239.1.1.1) : <104:0x00:0>(172.16.254.3, 239.1.2.0)] orig:172.16.255.3 RD:[1:1] Rmt-RD:[1:1] rt:3 snd:1
*Mar 27 12:13:17.151: MVPN(green[AF_IPv4]): Sending VxLAN BGP AD prefix=[3:172.16.255.3 1:1 : (10.1.101.11,239.1.1.1)] len=23, accept=1, af=0 <-- Send the MDT Data Adjacency prefix in VxLAN BGP to remote VTEPS
*Mar 27 12:13:17.151: MVPN(green[AF_IPv4]): Originate VxLAN BGP AD rt:3
*Mar 27 12:13:17.151: MVPN(green[AF_IPv4]): VXLAN MDT-Data, node added for (10.1.101.11,239.1.1.1) MDT: 239.1.2.0 <-- Add a node for the data group
Leaf-01#
VTEP del lado del receptor
Leaf#debug mvpn
<snip>
*Mar 27 12:27:54.920: MVPN: Received BGP prefix=[5: 1:1 : (10.1.101.11,239.1.1.1)] len=19, nexthop: 172.16.255.3, router-id: 172.16.255.1, Accept route
*Mar 27 12:27:54.920: MVPN: Received BGP route update for (10.1.101.11, 239.1.1.1) with RD: 1:1, Route Type: 5, flags: 0x00
*Mar 27 12:27:54.920: MVPN: Route Type 5 found [(10.1.101.11, 239.1.1.1), nh 172.16.255.3]rd:1:1 send:0
*Mar 27 12:27:54.920: MVPN: Received BGP prefix=[5: 1:1 : (10.1.101.11,239.1.1.1)] len=19, nexthop: UNKNOWN, router-id: 0.0.0.0, Withdraw route
*Mar 27 12:27:54.920: MVPN: Received BGP withdraw for (10.1.101.11, 239.1.1.1) with RD: 1:1, Route Type: 5, flags: 0x00
*Mar 27 12:27:54.920: MVPN: Route Type 5 deleted [(10.1.101.11, 239.1.1.1), nh 172.16.255.3] rd:1:1 send:0
*Mar 27 12:28:27.648: MVPN: Received BGP prefix=[5: 1:1 : (10.1.101.11,239.1.1.1)] len=19, nexthop: UNKNOWN, router-id: 0.0.0.0, Withdraw route
*Mar 27 12:28:27.657: MVPN: Received BGP withdraw for (10.1.101.11, 239.1.1.1) with RD: 1:1, Route Type: 5, flags: 0x00
*Mar 27 12:28:44.235: MVPN: Received BGP prefix=[5: 1:1 : (10.1.101.11,239.1.1.1)] len=19, nexthop: 172.16.255.3, router-id: 172.16.255.1, Accept route
*Mar 27 12:28:44.235: MVPN: Received BGP route update for (10.1.101.11, 239.1.1.1) with RD: 1:1, Route Type: 5, flags: 0x00
*Mar 27 12:28:44.235: MVPN: Route Type 5 added [(10.1.101.11, 239.1.1.1), nh 172.16.255.3] rd:1:1 send:0
*Mar 27 12:29:00.956: MVPN: Received BGP prefix=[3:172.16.255.3 1:1 : (10.1.101.11,239.1.1.1)] len=23, nexthop: 172.16.255.3, router-id: 172.16.255.2, remote-rd: 1:1, Accept route
*Mar 27 12:29:00.956: MVPN: Received BGP prefix=[3:172.16.255.3 1:1 : (10.1.101.11,239.1.1.1)] len=23, nexthop: 172.16.255.3, router-id: 172.16.255.1, remote-rd: 1:1, Accept route
*Mar 27 12:29:00.956: MVPN: Received BGP update <104:0x00:50901>(172.16.254.3, 239.1.2.0) next_hop:172.16.255.3 router_id:172.16.255.2 RD:[1:1] Rmt-RD:[1:1] route type:3 <-- Received BGP update from source side VTEP
*Mar 27 12:29:00.956: MVPN: LSM AD route added [(10.1.101.11,239.1.1.1) : <104:0x00:50901>(172.16.254.3, 239.1.2.0)] orig:172.16.255.3 RD:[1:1] Rmt-RD:[1:1] rt:3 snd:0 <-- Adding the Data group
*Mar 27 12:29:00.957: MVPN(green[AF_IPv4]): Activating PE (172.16.255.3, 1:1) ad route refcnt:1 control plane refcnt: 0
*Mar 27 12:29:00.958: MVPN(green[AF_IPv4]): Successfully notified datamdt group for NVE (239.1.2.0, TRUE, FALSE) <-- Notify NVE of the DATA MDT
*Mar 27 12:29:00.958: MVPN: Received BGP update <104:0x00:50901>(172.16.254.3, 239.1.2.0) next_hop:172.16.255.3 router_id:172.16.255.1 RD:[1:1] Rmt-RD:[1:1] route type:3
Leaf-03#
Troubleshoot
Orígenes de multidifusión no detectados |
| Antes de analizar por qué un flujo de multidifusión no funciona, es importante comprender la relación entre ARP y el reenvío de multidifusión Por lo general, cuando un host se activa y envía tráfico, las entradas ARP se completan con los procedimientos de detección de origen regulares. Pero, en el caso de los orígenes de multidifusión, es posible que el origen comience a enviar tráfico y el plano L2 en el FHR procese este tráfico de multidifusión sin la resolución de ARP para el origen. La finalización de ARP juega un papel importante en la funcionalidad de TRM por dos razones.
Asegúrese de que ARP esté resuelto y que el origen sea accesible dentro del entramado EVPN. |
Otras depuraciones útiles |
| En esta sección hay otras depuraciones que pueden ser útiles en el aislamiento de los problemas de TRM
|
Fuentes y receptores fuera del fabric |
| En algunos casos, el origen y/o el receptor pueden vivir uno o más saltos L3 lejos de los VTEP de la estructura. Este es un diseño válido, pero cambia qué tipo de ruta EVPN transporta la VRI y qué proceso es responsable de la creación de uniones en el VTEP receptor.
|
Topología de AS múltiple (de columna a columna) de eBGP |
| En algunos casos, la topología puede requerir que BGP envíe información de actualización a otro AS/Fabric. Es posible que transcurran hasta 30 segundos para que la información del plano de control BGP converja y la multidifusión comience a funcionar.
eBGP inter-as requiere un comando adicional Utilice la palabra clave inter-as para las rutas de la familia de direcciones MVPN para cruzar los límites del sistema autónomo (AS) BGP. Border-Leaf(config-vrf-af)#mdt auto-discovery vxlan inter-as |
Túnel de registro con L2VNI simétrico (FHR bloqueado en el estado de registro PIM) |
| En los casos en los que el VNI existe en el FHR y en otros VTEP, es posible que el FHR se quede atascado en el estado de registro Esto se debe al hecho de que la IP de origen del túnel de registro PIM es el gateway AnyCast. Cuando el RP recibe un registro PIM, no sabe cuál es el VTEP correcto para enviar la detención del registro, ya que la IP es común para múltiples dispositivos. Problema de Ruta de Túnel de Registro PIM (Leaf-01) Este es el FHR real: Envía mensajes de registro al RP Leaf-01#sh ip pim vrf green tunnel (Hoja-03): Este VTEP (y posiblemente otros) contiene la misma SVI y dirección IP que el FHR Leaf-03#sh ip pim vrf green tunnel (Leaf-01): El FHR permanece atascado en el Registro (no recibe un registro-parada del RP) Leaf-01#show ip mroute vrf green 226.1.1.1 10.1.101.11 (Leaf-02) Este es el RP: En este caso también posee la misma IP de AnyCast que el FHR, y por lo tanto se envía el registro-parada a sí mismo. Si el RP no tiene el l2vni pero 2 o 3 otros vteps sí, se puede enviar el registro-parada al VTEP incorrecto ya que el RP no tiene forma de seleccionar el correcto. Leaf-02#sh ip route vrf green 10.1.101.1 (Hoja-02): La depuración en el RP muestra el problema donde el RP tiene esta ruta como local conectado Leaf-02#debug ip pim vrf green 226.1.1.1 Solución de problema de ruta de túnel de registro PIM La solución es utilizar una IP de loopback única en todos los VTEP y utilizar la configuración indicada en esta sección. Leaf-01#sh run int lo 901 |
Información Relacionada
Guía de Configuración de EVPN VxLAN TRM
Troubleshooting de EVPN VxLAN Unicast
Guía de configuración de MVPN 17.3.x (switches Catalyst 9300)
Guía de configuración de MVPN 17.3.x (switches Catalyst 9500)
Historial de revisiones
| Revisión | Fecha de publicación | Comentarios |
|---|---|---|
3.0 |
17-May-2023 |
Escenario MDT de datos agregado |
2.0 |
10-Aug-2021 |
Se han corregido algunos problemas menores de redacción |
1.0 |
03-Jun-2021 |
Versión inicial |
ComentariosContacte a Cisco
- Abrir un caso de soporte
- (Requiere un Cisco Service Contract)