Esta configuración de muestra configura un EtherChannel entre un Cisco Catalyst 6500 en el que se ejecuta Catalyst OS (CatOS) y un switch Catalyst 3500XL. El EtherChannel se puede llamar Fast EtherChannel (FEC) o Gigabit EtherChannel (GEC). El nombre depende de la velocidad de las interfaces o de los puertos que utilice para formar el EtherChannel. Puede utilizar cualquiera de estos switches en este escenario para obtener los mismos resultados:
Cualquier Catalyst 4500/4000, 5500/5000, o 6500/6000 Series conmuta que los funcionamientos CatOS
2900XL o 3500XL Series Switch uces de los de la Configuración fija de la capa de Catalyst 2 (L2)
En este documento, dos puertos Fast Ethernet de cada uno del Switches se lían en un FEC. En este documento, los términos “FEC”, “GEC”, “Canal de puerto”, “canal”, y “grupo de puertos” todo refieren al EtherChannel.
Asegúrese de cumplir estos requisitos antes de intentar esta configuración:
Familiaridad con los comandos de utilizar para configurar el EtherChannel en un Catalyst 2900XL o 3500XL Switch
Para más información sobre los comandos, refiera a configurar la sección de los puertos del switch de la guía de configuración de software del Catalyst 2900XL y Catalyst 3500XL del documento, 12.0(5)WC5, 12.0(5)WC6.
Familiaridad con los comandos de utilizar para configurar el EtherChannel en un Switch que ejecuta CatOS
Para más información sobre los comandos, refiera a la sección del EtherChannel que configura de la guía de configuración de software de las Catalyst 6500 Series del documento, 8.7.
La información que contiene este documento se basa en las siguientes versiones de software y hardware.
El Catalyst 3500XL Switch (modelo WS-C3524-PWR-XL-EN) ese funciona con el Software Release 12.0(5)WC9 de Cisco IOS®
Catalyst 6500 Switch (modelo 6506 con el Supervisor Engine II) que funciona con la versión 8.2.1 del software CatOS
La información que contiene este documento se creó a partir de los dispositivos en un ambiente de laboratorio específico. Todos los dispositivos que se utilizan en este documento se pusieron en funcionamiento con una configuración verificada (predeterminada). Si la red está funcionando, asegúrese de haber comprendido el impacto que puede tener cualquier comando.
Consulte Convenciones de Consejos TécnicosCisco para obtener más información sobre las convenciones del documento.
Usted debe crear manualmente el EtherChannel porque los Catalyst 2900XL/3500XL Switch no soportan el Port Aggregation Protocol (PAgP); PAgP del soporte de los switches CatOS. El PAgP facilita la creación automática del FEC y del GEC. Para más información sobre el PAgP, refiera a la sección del EtherChannel que configura de la guía de configuración de software de las Catalyst 6500 Series del documento, 8.7.
Cree el Canal de puerto en la orden de estos pasos:
Note: Cuando usted realiza los pasos en esta orden, usted evita los Posibles problemas con el Spanning Tree Protocol (STP) que puede ocurrir durante el proceso de configuración. El STP puede apagar los puertos con el estado errdisable en el Catalyst 6500 Switch si usted configura el switch CatOS mientras que un canal antes de que usted configure el switch XL como canal.
Publique el comando set port disable module/port en el switch CatOS.
Los comandos estableces para inhabilitar el modo los puertos para el uso en la canalización del puerto.
Cree el Canal de puerto (grupo de puertos) en el switch XL.
Cree el Canal de puerto en el switch CatOS.
Note: Esté seguro de fijar al modo del canal a "ON". Esta configuración es necesaria para inhabilitar el PAgP en los puertos y forzar los puertos para formar un canal.
Publique el comando set port enable module/port en el switch CatOS.
El comando vuelve a permitir los puertos que fueron inhabilitados anterior.
En esta sección encontrará la información para configurar las funciones descritas en este documento.
Note: Use la herramienta Command Lookup Tool (clientes registrados solamente) para encontrar más información sobre los comandos usados en este documento.
En este documento, se utiliza esta configuración de red:
En este documento, se utilizan estas configuraciones:
Catalyst 3524XL |
---|
Current configuration: ! version 12.0 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname cat3500 ! enable password mysecret !--- This is the privileged mode password for the example. ! ! ! ! ! ip subnet-zero ! ! ! interface FastEthernet0/1 port group 1 !--- The port group <group-number> command !--- makes this interface a member of channel group 1. ! interface FastEthernet0/2 port group 1 !--- This interface is also a member of channel group 1. ! interface VLAN1 ip address 10.10.10.2 255.255.255.0 !--- This is the IP address for management. no ip directed-broadcast no ip route-cache ! ! line con 0 transport input none stopbits 1 line vty 0 4 password mysecret !--- This is the Telnet password for the example. login line vty 5 15 login ! end cat3500# |
Catalyst 6506 |
---|
begin ! # ***** NON-DEFAULT CONFIGURATION ***** ! ! #time: Sun Feb 1 2004, 14:03:48 ! #version 8.2(1) ! !--- Output suppressed. ! #ip set interface sc0 1 10.10.10.3/255.255.255.0 10.10.10.255 !--- This is the IP address for management. ! !--- Output suppressed. ! #port channel set port channel 2/1-2 15 !--- The set port channel <module/port> command !--- creates an EtherChannel on switches that run CatOS. !--- The admin group (15, in this case) is not configured, !--- but is a number that the system assigns randomly. # default port status is enable ! ! #module 1 : 2-port 1000BaseX Supervisor ! #module 2 : 48-port 10/100BaseTX Ethernet set port channel 2/1-2 mode on !--- The set port channel <module/port> mode on command disables PAgP. !--- The disablement forces the ports to form a channel with the XL switch !--- that does not support PAgP. ! #module 3 empty ! #module 4 empty ! #module 5 empty ! #module 6 empty ! #module 15 : 1-port Multilayer Switch Feature Card ! #module 16 empty end cat6506> (enable) |
Use esta sección para confirmar que su configuración funciona correctamente.
La herramienta Output Interpreter Tool (clientes registrados solamente) (OIT) soporta ciertos comandos show. Utilice la OIT para ver un análisis del resultado del comando show.
Verifique el canal del puerto en el switch Catalyst 2900XL/3500XL:
show port group
show port group group-number
Verifique el estado del árbol de expansión en el switch Catalyst 2900XL/3500XL:
show spanning-tree
Verifique el canal del puerto en el switch CatOS:
show port capabilities module
show port channel
mostrar módulo de canal de puerto/puerto
show port channel info
Marque atravesar - estatus del árbol en el switch CatOS:
show spantree
show spantree vlan
show spantree module/port
show port group
cat3500# show port group Group Interface Transmit Distribution ----- --------------------- --------------------- 1 FastEthernet0/1 source address 1 FastEthernet0/2 source address cat3500#
show spanning-tree
cat3500# show spanning-tree Spanning tree 1 is executing the IEEE compatible Spanning Tree protocol Bridge Identifier has priority 32768, address 00d0.5868.f180 Configured hello time 2, max age 20, forward delay 15 Current root has priority 32768, address 00d0.020e.2c00 Root port is 1, cost of root path is 12 Topology change flag not set, detected flag not set, changes 10 Times: hold 1, topology change 35, notification 2 hello 2, max age 20, forward delay 15 Timers: hello 0, topology change 0, notification 0 Interface Fa0/1 (port 1) in Spanning tree 1 is FORWARDING Port path cost 12, Port priority 128 Designated root has priority 32768, address 00d0.020e.2c00 Designated bridge has priority 32768, address 00d0.020e.2c00 Designated port is 33, path cost 0 Timers: message age 2, forward delay 0, hold 0 BPDU: sent 4, received 633 Interface Fa0/3 (port 15) in Spanning tree 1 is down Port path cost 100, Port priority 128 Designated root has priority 32768, address 00d0.020e.2c00 Designated bridge has priority 32768, address 00d0.5868.f180 !--- Output suppressed.
Note: Esta salida no visualiza el Fa0/2 de la interfaz porque la interfaz se lía con el Fa0/1 en el Canal de puerto. Vea el (port 1) en la salida.
muestre el módulo de las capacidades de puerto — Utilice este comando de marcar si el EtherChannel de los soportes del módulo.
cat6506> (enable) show port capabilities 2 Model WS-X6348-RJ-45 Port 2/1 Type 10/100BaseTX Speed auto,10,100 Duplex half,full Trunk encap type 802.1Q,ISL Trunk mode on,off,desirable,auto,nonegotiate Channel yes Broadcast suppression percentage(0-100) Flow control receive-(off,on),send-(off) Security yes Membership static,dynamic Fast start yes QOS scheduling rx-(1q4t),tx-(2q2t) CoS rewrite yes ToS rewrite DSCP UDLD yes Inline power auto,off AuxiliaryVlan 1..1000,1025..4094,untagged,dot1p,none SPAN source,destination COPS port group 2/1-48 Link debounce timer yes Dot1q-all-tagged yes -------------------------------------------------------------- Model WS-X6348-RJ-45 Port 2/2 Type 10/100BaseTX Speed auto,10,100 Duplex half,full Trunk encap type 802.1Q,ISL Trunk mode on,off,desirable,auto,nonegotiate Channel yes Broadcast suppression percentage(0-100) Flow control receive-(off,on),send-(off) Security yes Membership static,dynamic Fast start yes QOS scheduling rx-(1q4t),TX(2q2t) COs rewrite yes ToS rewrite DSCP UDLD yes Inline power auto,off AuxiliaryVlan 1..1000,1025..4094,untagged,dot1p,none SPAN source,destination COPS port group 2/1-48 Link debounce timer yes Dot1q-all-tagged yes -------------------------------------------------------------- !--- Output suppressed.
show port channel
cat6506> (enable) show port channel Port Status Channel Admin Ch Mode Group Id ----- ---------- -------------------- ----- ----- 2/1 connected on 15 1762 2/2 connected on 15 1762 Port Device-ID Port-ID Platform ----- ------------------------------- ------------------------- ---------------- 2/1 cat3500 FastEthernet0/1 cisco WS-C3524-PWR-XL 2/2 cat3500 FastEthernet0/2 cisco WS-C3524-PWR-XL cat6506> (enable)
show port channel info
cat6506> (enable) show port channel info Switch Frame Distribution Method: ip both Port Status Channel Admin Channel Speed Duplex Vlan mode group id ----- ---------- -------------------- ----- ------- ----- ------ ---- 2/1 connected on 15 1762 a-100 a-full 1 2/2 connected on 15 1762 a-100 a-full 1 Port Channel Oper-group Neighbor Oper-Distribution PortSecurity/ ifIndex Oper-group Method Dynamic port ----- ------- ---------- ---------- ----------------- ------------- 2/1 67 241 ip both 2/2 67 241 ip both Port Device-ID Port-ID Platform ----- ------------------------------- ------------------------- ---------------- 2/1 cat3500 FastEthernet0/1 cisco WS-C3524-PWR-XL 2/2 cat3500 FastEthernet0/2 cisco WS-C3524-PWR-XL !--- Output suppressed.
show spantree vlan
cat6506> (enable) show spantree 1 VLAN 1 Spanning tree mode RAPID-PVST+ Spanning tree type ieee Spanning tree enabled Designated Root 00-04-9b-bf-04-00 Designated Root Priority 32768 Designated Root Cost 0 Designated Root Port 1/0 Root Max Age 20 sec Hello Time 2 sec Forward Delay 15 sec Bridge ID MAC ADDR 00-04-9b-bf-04-00 Bridge ID Priority 32768 Bridge Max Age 20 sec Hello Time 2 sec Forward Delay 15 sec Port State Role Cost Prio Type ------------------------ ------------- ---- --------- ---- -------------------- 1/1 not-connected - 4 32 1/2 not-connected - 4 32 2/1-2 forwarding DESG 12 32 P2P, PEER(STP) 2/3 not-connected - 100 32 2/4 not-connected - 100 32 2/5 not-connected - 100 32 2/6 not-connected - 100 32 !--- Output suppressed.
show spantree module/port
cat6506> (enable) show spantree 2/1 Edge Port: No, (Configured) Default Link Type: P2P, (Configured) Auto Port Guard: Default Port Vlan State Role Cost Prio Type ------------------------ ---- ------------- ---- --------- ---- ----------------- 2/1-2 1 forwarding DESG 12 32 P2P, PEER(STP) cat6506> (enable) cat6506> (enable) show spantree 2/2 Edge Port: No, (Configured) Default Link Type: P2P, (Configured) Auto Port Guard: Default Port Vlan State Role Cost Prio Type ------------------------ ---- ------------- ---- --------- ---- ----------------- 2/1-2 1 forwarding DESG 12 32 P2P, PEER(STP) cat6506> (enable)
Note: La salida del comando show spantree module/port para los puertos 2/1 y 2/2 visualiza los resultados idénticos porque los puertos se agrupan juntos en un canal.
Actualmente, no hay información específica de troubleshooting disponible para esta configuración.