Sustitución del conmutador central Nexus 9236C - CPAR
Contenido
Introducción
Este documento describe los pasos necesarios para sustituir un conmutador central defectuoso (Nexus 9236C) en una configuración Ultra-M.
Este procedimiento se aplica a un entorno Openstack a través de la versión NEWTON donde ESC no administra Cisco Prime Access Registrar (CPAR) y CPAR se instala directamente en la VM implementada en Openstack.
Antecedentes
Ultra-M es una solución de núcleo de paquetes móviles virtualizada validada y empaquetada previamente diseñada para simplificar la implementación de VNF. Los servidores que forman parte de la configuración Ultra-M están conectados a tres tipos diferentes de switches :
- Catalyst Switch
- Switch de hoja
- Switch de columna
Esta imagen muestra la topología de red de una configuración Ultra-M:
Este documento está dirigido al personal de Cisco que está familiarizado con la configuración de Cisco Ultra-M y las operaciones del switch Catalyst.
Abreviaturas
| VNF | Función de red virtual |
| SPINE | Switch Nexus 9236C como columna |
| MOP | Método de procedimiento |
| LAN | Red de área local |
| FTP | File Transfer Protocol |
| TFTP | Trivial File Transfer Protocol |
| CIMC | Controlador de gestión integrada de Cisco |
Flujo de trabajo del MoP
Esta imagen muestra el flujo de trabajo de alto nivel del procedimiento de reemplazo.
Switch de columna en la configuración UltraM
Requisito previo
Realice una copia de seguridad del archivo de configuración desde el switch de columna a través de FTP/TFTP antes de continuar con el reemplazo del switch.
AL03-N9236c-POD2-spine1# copy running-config sftp:
Enter destination filename: [AL03-N9236c-POD2-spine1-running-config] backup-spine-cfg-2
Enter vrf (If no input, current vrf 'default' is considered): management
Enter hostname for the sftp server: 10.1.1.1
Enter username: root
The authenticity of host '10.1.1.1 (10.1.1.1)' can't be established.
ECDSA key fingerprint is SHA256:dnHSXQ6fyYX5v8DU87oqVkCoA8CSPW7CpT+o2qilNI4.
Are you sure you want to continue connecting (yes/no)? yes
Warning: Permanently added '10.1.1.1' (ECDSA) to the list of known hosts.
root@10.1.1.1's password:
Connected to 10.1.1.1.
sftp> put /var/tmp/vsh/backup-spine-cfg-2 backup-spine-cfg-2
Uploading /var/tmp/vsh/backup-spine-cfg-2 to /root/backup-spine-cfg-2
/var/tmp/vsh/backup-spine-cfg-2 0% 0 0.0KB/s --:-- ETA /var/tmp/vsh/backup-spine-cfg-2 100% 11KB 11.2KB/s 00:00
sftp> exit
Copy complete, now saving to disk (please wait)...
Copy complete.
Comprobaciones de estado
Paso 1. Verifique la versión de software actual que se ejecuta en el switch y anótela.
AL03-N9236c-POD2-spine1# show ver
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2018, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source. This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0 or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.
Software
BIOS: version 07.59
NXOS: version 7.0(3)I7(3)
BIOS compile time: 08/26/2016
NXOS image file is: bootflash:///nxos.7.0.3.I7.3.bin
NXOS compile time: 2/12/2018 13:00:00 [02/12/2018 19:13:48]
Hardware
cisco Nexus9000 C9236C chassis
Intel(R) Xeon(R) CPU @ 1.80GHz with 16400560 kB of memory.
Processor Board ID FDO211613CA
Device name: AL03-N9236c-POD2-spine1
bootflash: 53298520 kB
Kernel uptime is 134 day(s), 14 hour(s), 48 minute(s), 25 second(s)
Last reset at 705173 usecs after Fri Mar 2 17:56:31 2018
Reason: Reset due to upgrade
System version: 7.0(3)I5(2)
Service:
plugin
--More-- Core Plugin, Ethernet Plugin
Active Package(s):
Paso 2. Verifique el uso actual de la licencia.
AL03-N9236c-POD2-spine1# show license uasgesage
Feature Ins Lic Status Expiry Date Comments
Count
--------------------------------------------------------------------------------
N9K_LIC_1G No - Unused -
VPN_FABRIC No - Unused -
FCOE_NPV_PKG No - Unused -
SECURITY_PKG No 0 Unused -
N9K_UPG_EX_10G No - Unused -
TP_SERVICES_PKG No - Unused -
NXOS_ADVANTAGE_GF No - Unused -
NXOS_ADVANTAGE_M4 No - Unused -
NXOS_ADVANTAGE_XF No - Unused -
NXOS_ESSENTIALS_GF No - Unused -
NXOS_ESSENTIALS_M4 No - Unused -
NXOS_ESSENTIALS_XF No - Unused -
SAN_ENTERPRISE_PKG No - Unused -
PORT_ACTIVATION_PKG No 0 Unused -
NETWORK_SERVICES_PKG No - Unused -
NXOS_ADVANTAGE_M8-16 No - Unused -
NXOS_ESSENTIALS_M8-16 No - Unused -
FC_PORT_ACTIVATION_PKG No 0 Unused -
LAN_ENTERPRISE_SERVICES_PKG Yes - In use Never -
--------------------------------------------------------------------------------
Paso 3. Asegúrese de que los cables físicos conectados al canal de puerto del switch, la Vlan y también el estado del puerto sean los adecuados según lo esperado.
AL03-N9236c-POD2-spine1# show interface status | grep connected
mgmt0 -- connected routed full 100 --
Eth1/1 Connected to leaf1 connected trunk full 100G QSFP-100G-AOC5M
Eth1/2 Connected to leaf1 connected trunk full 100G QSFP-100G-AOC5M
Eth1/4 Connected to leaf2 connected trunk full 100G QSFP-100G-AOC5M
Eth1/5 Connected to leaf2 connected trunk full 100G QSFP-100G-AOC5M
Eth1/7 Connected to Leaf3 connected trunk full 100G QSFP-100G-AOC5M
Eth1/8 Connected to Leaf3 connected trunk full 100G QSFP-100G-AOC5M
Eth1/10 connect leaf4 connected trunk full 100G QSFP-100G-AOC5M
Eth1/11 connect leaf4 connected trunk full 100G QSFP-100G-AOC5M
Eth1/21/1 Connected to NMNET connected 101 full 10G QSFP-40G-SR4
Eth1/29 Connected to AL04- connected trunk full 100G QSFP-100G-AOC5M
Eth1/30 Connected to AL04- connected trunk full 100G QSFP-100G-AOC5M
Eth1/36/1 connected to ARG | connected routed full 10G QSFP-40G-SR4
Eth1/36/2 connected to ARG | disabled routed auto auto QSFP-40G-SR4
Eth1/36/3 connected to ARG | disabled routed auto auto QSFP-40G-SR4
Eth1/36/4 connected to ARG | disabled routed auto auto QSFP-40G-SR4
Po10 -- connected routed full 10G --
Po10.3101 -- connected routed full 10G --
Po10.3109 -- connected routed full 10G --
Po18 -- connected trunk full 100G --
Po21 -- connected trunk full 100G --
Po22 -- connected trunk full 100G --
Po25 -- connected trunk full 100G --
Po26 -- connected trunk full 100G --
Lo1 -- connected routed auto auto --
Vlan101 -- connected routed auto auto --
Vlan1025 vPCRF 1 and vPCRF connected routed auto auto --
Vlan1026 Replication for vP connected routed auto auto --
Vlan1031 External Traffic v connected routed auto auto --
Vlan1032 External External connected routed auto auto --
Vlan1033 External Traffic connected routed auto auto --
Vlan1034 External Traffic v connected routed auto auto --
Vlan1035 External Traffic v connected routed auto auto --
Vlan1036 External Traffic v connected routed auto auto --
Vlan1041 External Traffic A connected routed auto auto --
Vlan1042 External Traffic A connected routed auto auto --
Vlan1043 External Traffic A connected routed auto auto --
Vlan2601 Global Interchassi connected routed auto auto --
Vlan2602 NMNET Interchassis connected routed auto auto --
Paso 4. Asegúrese de que los vecinos BGP estén activos.
AL03-N9236c-POD2-spine1# show ip bgp summary vrf all
BGP summary information for VRF NMNET, address family IPv4 Unicast
BGP router identifier 10.225.247.201, local AS number 65361
BGP table version is 2, IPv4 Unicast config peers 2, capable peers 1
0 network entries and 0 paths using 0 bytes of memory
BGP attribute entries [0/0], BGP AS path entries [0/0]
BGP community entries [0/0], BGP clusterlist entries [0/0]
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
10.0.100.6 4 65361 193834 193833 2 0 0 19w1d 0
10.250.180.185 4 65137 0 0 0 0 0 19w1d Idle
BGP summary information for VRF default, address family IPv4 Unicast
BGP router identifier 10.0.200.1, local AS number 65361
BGP table version is 161, IPv4 Unicast config peers 2, capable peers 2
18 network entries and 29 paths using 5700 bytes of memory
BGP attribute entries [3/480], BGP AS path entries [1/6]
BGP community entries [0/0], BGP clusterlist entries [0/0]
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
10.0.100.2 4 65361 3868481 3868419 161 0 0 19w1d 12
10.163.140.225 4 65137 3868521 3868365 161 0 0 19w1d 5
AL03-N9236c-POD2-spine1# show ipv6 bgp summary vrf all
Paso 5. Asegúrese de que el estado de los vecinos BFD esté activo.
AL03-N9236c-POD2-spine1# show bfd neighbors vrf all
OurAddr NeighAddr LD/RD RH/RS Holdown(mult) State Int Vrf
10.163.140.226 10.163.140.225 1090519042/1090519042 Up 107(3) Up Po10.3101 default
AL03-N9236c-POD2-spine1# show bfd ipv6 neighbor vrf all
Procedimiento de sustitución del switch
Paso 1. Instale el nuevo switch en el rack y conecte los cables al switch como se ha indicado. Los pasos para la instalación del switch se pueden encontrar en este enlace: Guía de Instalación del Hardware del Switch de Modo NX-OS Nexus de columna 236C
Paso 2. Compruebe la versión de software del switch Nexus Spine y actualice/reduzca a la versión de software según el enlace dado: Guía de actualización y actualización de software Cisco Nexus serie 9000 NX-OS, versión 7.x
Paso 3. Transfiera la copia de seguridad de la configuración al nuevo switch y copie esa configuración al startup-config.
server-backup$ sftp admin@10.1.1.1
The authenticity of host '10.1.1.1 (10.1.1.1)' can't be established.
RSA key fingerprint is SHA256:fnbUmd2mL5yE94zxrRoKAlvYfQbheXJfQox7m3XfpIU.
Are you sure you want to continue connecting (yes/no)? yes
Warning: Permanently added '10.1.1.1' (RSA) to the list of known hosts.
User Access Verification
Password:
Password:
Connected to 10.1.1.1.
sftp> ls
20170607_193430_poap_15489_1.log 20170607_193430_poap_15489_2.log 20170607_193430_poap_15489_init.log backup-spine-cfg-2 backup-spine.cfg
backup_run_02152018 bios_daemon.dbg cfg-july25th cfg-july25th-spine1 flash:
flash:cfg-aug8th-ybattina-afterNSO flash:cfg-jul28th home l3-cfg-aug10th license_FDO211406K1_16.lic
lost+found nxos.7.0.3.I4.4.bin nxos.7.0.3.I5.2.bin nxos.7.0.3.I7.3.bin platform-sdk.cmd
scripts spine-config-bkp starat virtual-instance vlan.dat 100% 33KB 21.7KB/s 00:01
sftp> put backup-spine-cfg-2
Uploading backup-spine-cfg-2 to /backup-spine-cfg-2
backup-spine-cfg-2 100% 33KB 23.5KB/s 00:01
sftp> bye
AL03-N9236c-POD2-spine1# copy bootflash:///backup-spine-cfg-2 startup-config
Copy progress 100% 33KB
Copy complete, now saving to disk (please wait)...
Copy complete.
Paso 4. Recargue el switch después de cargar la configuración de respaldo.
AL03-N9236c-POD2-spine1#reload
Verificación del switch de columna reemplazada
Después de que el switch esté disponible para el acceso, realice las comprobaciones de estado a través de estos comandos en el switch de columna para verificar que el switch sustituido esté disponible en el estado esperado.
AL03-N9236c-POD2-spine1# show port-channel summary
AL03-N9236c-POD2-spine1# show ip bgp summary vrf all
AL03-N9236c-POD2-spine1# show ipv6 bgp summary vrf all
AL03-N9236c-POD2-spine1# show bfd neighbor vrf all
AL03-N9236c-POD2-spine1# show bfd ipv6 neighbor vrf all
ComentariosContacte a Cisco
- Abrir un caso de soporte
- (Requiere un Cisco Service Contract)