|
|
Client Name |
Specifies a name for your client adapter on the wireless network. Option: Up to 16 alphanumeric characters Default: None |
SSID1 |
Service set identifier (SSID) or network name identifies the specific wireless network that you want to access. See the note below. Option: Up to 32 ASCII characters (case sensitive) Default: None |
SSID2 |
Identifies an optional SSID or network name for a second wireless network that enables you to roam to the network without having to reconfigure your client adapter. See the note below. Option: Up to 32 ASCII characters (case sensitive) Default: None |
SSID3 |
Identifies an optional SSID or network name for a third wireless network that enables you to roam to the network without having to reconfigure your client adapter. See the note below. Option: Up to 32 ASCII characters (case sensitive) Default: None |
Note If you do not specify an SSID parameter, your client adapter can associate to any access point on the network that is configured to allow broadcast SSIDs (see the AP Radio Hardware page in the Cisco Aironet Access Point Software Configuration Guide). If the access points with which you wish to communicate are not configured to allow broadcast SSIDs, the value of this parameter must match the SSID of the access points. Otherwise, you will not be able to access the wireless network. |
Network Type |
Specifies the type of network in which your client adapter is installed. Options: infrastructure or ad hoc Default: infrastructure |
Network Type |
Description |
infrastructure |
Also referred to as Computer to Access Point. Used to set up a connection to a wired Ethernet network (through an access point). |
ad hoc |
Also referred to as computer to computer or peer to peer. Used to set up a small network between two or more wireless devices. For example, an ad hoc network could be set up between computers in a conference room so users can share information in a meeting. |
Authentication Type |
Defines how your client adapter attempts to authenticate to an access point. Options: open or shared Default: open |
Authentication |
Description |
open |
Allows your client adapter, regardless of its WEP settings, to authenticate and attempt to communicate with an access point. |
shared |
Allows your client adapter to communicate only with access points that have the same WEP keys. The access point sends a known unencrypted challenge packet to the client adapter, which encrypts the packet and sends it back to the access point. The access point attempts to decrypt the encrypted packet and sends an authentication response packet indicating the success or failure of the decryption back to the client adapter. |
Note If LEAP is enabled on your client adapter, Open is the only available option.
Note The Shared Authentication option is available only if the client adapter has been assigned a WEP key and WEP is enabled. Refer to Chapter 4 of the Cisco Aironet Wireless LAN Adapters Installation and Configuration Guide for MacOS for instructions on setting a WEP key and enabling WEP.
|
Enable WEP |
Enables or disables Wired Equivalent Privacy (WEP) for your client adapter. If you want to enable WEP for your client adapter, you must specify yes and create a WEP key using the ACU. You can disable WEP by specifying no. Refer to Refer to Chapter 4 of the Cisco Aironet Wireless LAN Adapters Installation and Configuration Guide for MacOS for more information on WEP and instructions on setting a WEP key. Options: yes or no Default: no |
Enable LEAP |
Enables or disables LEAP (also referred to as EAP - Cisco Wireless) for your client adapter. If you want to enable LEAP for your client adapter, you must specify yes and set a LEAP username and password using the ACU. Refer to Refer to Chapter 4 of the Cisco Aironet Wireless LAN Adapters Installation and Configuration Guide for MacOS for more information about LEAP and instructions on setting a LEAP username and password. Options: yes or no Default: no |
Transmit Power |
Defines the power level at which your client adapter transmits signals. This value must not be higher than that allowed by your country's regulatory agency (FCC in the U.S., DOC in Canada, ETSI in Europe, MKK in Japan, etc.). When World Mode is enabled, only the transmit power levels supported by the country of operation's regulatory agency are available (refer to Appendix D of the Cisco Aironet Wireless LAN Adapters Installation and Configuration Guide for MacOS). Range: 1, 5, 15, 30 mW (340 series client adapters) 1, 5, 20, 30, 50, or 100 mW (350 series client adapters) Default: Minimum level allowed by your country's regulatory agency
Note Reducing the transmit power level conserves battery power but decreases radio range.
|
Power Mode |
Sets your client adapter to its optimum power consumption setting. Options CAM, PSP, or Maximum Default: CAM |
Power Save Mode |
Description |
CAM (Constantly Awake Mode) |
Keeps the client adapter powered up continuously so there is little lag in message response time. Consumes the most power but offers the highest throughput. Is recommended for desktop computers and devices that use AC power. |
PSP (Power Save Mode) |
Switches between a PSP mode and CAM, depending on network traffic. This mode switches to CAM when retrieving a large number of packets and switches back to PSP after the packets have been retrieved. Is recommended when power consumption is a concern but you need greater throughput than that allowed by Max PSP. |
Maximum (Max Power Savings) |
Causes the access point to buffer incoming messages for the client adapter, which wakes up periodically and polls the access point to see if any buffered messages are waiting for it. The adapter can request each message and then go back to sleep. Conserves the most power but offers the lowest throughput. Is recommended for devices for which power consumption is the ultimate concern (such as small battery-powered devices). |
Mixed Cells |
If your network's access points are set to communicate with both WEP-enabled or WEP-disabled clients (that is, if the Use of Data Encryption by Stations parameter on the AP Radio Data Encryption screen is set to Optional), you must specify yes, even if your client adapter is not using WEP. If you specify no, your client adapter will not be able to establish a connection with the access point.
Note For security reasons, Cisco recommends that both WEP-enabled and WEP-disabled clients not be allowed in the same cell because broadcast packets will be sent unencrypted, even to clients running WEP.
Options: yes or no Default: no |
Transmit Antenna |
Specifies the type of antenna that your client adapter uses to receive data. Options: both, right, or left •PC card - The PC card's integrated, permanently attached antenna operates best when used in diversity mode. Diversity mode enables the card to use the better signal from its two antenna ports. Default: both (Diversity) •LM card - The LM card is shipped without an antenna; however, an antenna can be connected through the card's external connector. If a snap-on antenna is used, diversity mode is recommended. Otherwise, select the mode that corresponds to the antenna port to which the antenna is connected. Default: both (Diversity) •PCI client adapter - The PCI client adapter must use the right antenna option. Default: right |
Receive Antenna |
Specifies the antenna that your client adapter uses to transmit data. See the Transmit Antenna parameter above for information on the options available for your client adapter. |
World Mode |
Selecting this checkbox enables the client adapter to assume the legal transmit power level and channel set of the access point to which it is associated. This parameter is available only in computer to access point (infrastructure) mode and is designed for users who travel between countries because it allows the adapter to be used in different regulatory domains. Options: yes or no Default: no
Note When World Mode is enabled, only the transmit power levels supported by the country of operation's regulatory agency are available.
|
Channel |
Specifies which frequency your client adapter will use as the channel for communications. These channels conform to the IEEE 802.11 Standard for your regulatory domain. •In infrastructure mode, this parameter is set automatically and cannot be changed. The client adapter listens to the entire spectrum, selects the best access point to associate to, and uses the same frequency as that access point. •In ad hoc mode, the channel of the client adapter must be set to match the channel used by the other clients with which you wish to communicate. Options: 1 to 11 (Dependent on regulatory domain) Example: 1 (Channel 1, 2412 MHz)
Note Refer to Appendix D of the Cisco Aironet Wireless LAN Adapters Installation and Configuration Guide for MacOS for a list of channel identifiers, channel center frequencies, and regulatory domains.
|
Wep Transmit Key |
Specifies the WEP key to use to transmit packets. Options: 1, 2, 3, or 4 Default: 1 |
LEAP Username |
Specifies the LEAP username.
Note In some networks, you must enter the domain name prior to the username, such as domain\ username, where domain represents the domain name.
Options: Unique name (alphanumeric characters) Default: None |