Apn Agg Max Bit Rate DL
|
Defines the total bandwidth
usage for the downlink direction of non-GBR QCIs at the APN.
|
Apn Agg Max Bit Rate UL
|
Defines the total bandwidth
usage for the uplink direction of non-GBR QCIs at the APN.
|
Arp
|
AllocationRetentionPriority
-
Priority Level – Priority-Level AVP value.
-
Preemption Capability – Preemption-Capability AVP value
-
Preemption Vulnerability – Preemption-Vulnerability AVP value.
|
Balance
Code
|
Indicates
with which balance the quota is associated. You can subscribe to multiple
balances, but the monitoring key is associated with one balance.
|
Diameter Client
|
The client
configuration is used to apply different policies based on PCEF type.
To filter a service based on the Diameter client, specify which
Diameter client you want the service to be applied to. Diameter clients are
configured in the
section of the interface.
This
parameter is optional.
|
Dosage
|
How much
quota to initially give the client (in bytes).
Default: 0
|
Dual Stack
Session
|
Can be set
to enabled or disabled.
Default:
disabled
|
Enable
Resource Allocation Notification
|
Can be set
to enabled or disabled.
Default:
disabled
|
Encoding
Format
|
Can be set
to true or false. If the Monitoring Key parameter is numeric, set this
parameter to true.
Default:
false
|
Event
Trigger
|
Used
primarily to notify the starting and stopping of applications or to report
usage. It is not used to rerequest rules.
|
Flow
Status
|
Defines
whether the service data flow is enabled or disabled.
|
Framed I P
Type
|
Can be set
to one of the following options:
-
ANY_ONE
-
BOTH
-
IPv4_ADDRESS
-
IPv6_ADDRESS
Default:
ANY_ONE
|
Guaranteed Bit Rate DL
|
Defines the guaranteed bit rate allowed for the downlink
direction.
|
Guaranteed Bit Rate UL
|
Defines the guaranteed bit rate allowed for the uplink
direction.
|
List of
Input Column Avp Pairs (List)
|
Defines
the mapping between the AVP Names and the key columns defined in the selected
STG. These AVPs are used as inputs while evaluating the CRD table in STG.
-
Avp
Name – The name of the Diameter AVP that is used as input for CRD table
evaluation. For example: Flow-Number, Media-Component-Number, and so on.
-
Column
– The key column in STG that corresponds to the specified AVP.
|
List Of
Output Column Avp Pairs (List)
|
Defines
the mapping between the AVP Names and the output columns defined in the
selected STG. These mappings indicate how the output columns' values are mapped
to AVPs after the CRD is evaluated.
-
Avp
Name – The name of the Diameter AVP to which the value of the output column is
mapped while setting the charging parameters on the dynamic rule (for the
Dedicated Bearer). For example: Rating-Group Service-Identifier.
-
Column
– The output column defined in the selected STG.
|
Max Req Bandwidth DL
|
Defines the maximum bit rate
allowed for the downlink direction.
|
Max Req Bandwidth UL
|
Defines the maximum bit rate
allowed for the uplink direction.
|
Monitoring
Key
|
Identifies
a usage monitoring control instance. You can specify any value.
|
Monitoring
Level
|
Can be set
to one of the following values:
-
SESSION_LEVEL (0)
-
PCC_RULE_LEVEL (1)
-
ADC_RULE_LEVEL (2)
|
Mute
Notification
|
Indicates
whether notifications for application starts and stops are muted for ADC Rule
by the TDF.
|
New String
Value
|
The new
string value that is used to overwrite the “String Value” if the value of
“String Value” field matches exactly with the value of “String Value To
Override”.
|
Online
|
Defines
whether the online charging interface from the PCEF for the associated PCC rule
is enabled. The default charging method provided by the CPS takes precedence
over any preconfigured default charging method at the PCEF.
|
Offline
|
Defines
whether the offline charging interface from the PCEF for the associated PCC
rule is enabled. The default charging method provided by the CPS takes
precedence over any preconfigured default charging method at the PCEF.
|
Precedence
|
Defines
the second level priority when the highest priority matches among the multiple
generic service configurations.
|
Preemption Capability
|
When provided within the QoS-Information AVP, the AVP defines
whether a service data flow can get resources that were already assigned to
another service data flow that has a lower priority level. If it is provided
within the Default-EPS-Bearer-QoS AVP, the AVP defines whether the Default
Bearer can get resources that were already assigned to another bearer with a
lower priority level.
-
0: Indicates that the service data flow or bearer is allowed to
get resources that were already assigned to another service data flow or bearer
with a lower priority level.
-
1: Indicates that the service data flow or bearer is not allowed
to get resources that were already assigned to another service data flow or
bearer with a lower priority level. This is the default value applicable if
this AVP is not supplied.
|
Preemption Vulnerability
|
When provided within the QoS-Information AVP, the AVP defines
whether a service data flow can lose the resources assigned to it in order to
admit a service data flow that has a higher priority level. If it is provided
within the Default-EPS-Bearer-QoS AVP, the AVP defines whether the Default
Bearer can lose the resources assigned to it in order to admit a pre-emption
capable bearer with a higher priority level.
-
0: Indicates that the resources assigned to the service data
flow or bearer can be pre-empted and allocated to a service data flow or bearer
with a higher priority level. This is the default value applicable if this AVP
is not supplied.
-
1: Indicates that the resources assigned to the service data
flow or bearer cannot be pre-empted and allocated to a service data flow or
bearer with a higher priority level.
|
Priority
|
The
priority of the message for processing. The higher the number, the higher the
priority.
Default
for most settings: 0
|
Priority
Levels
|
Used to
decide whether a bearer establishment or modification request can be accepted,
or rejected due to resource limitations (typically used for admission control
of GBR traffic). The AVP can also be used to decide which existing bearers to
pre-empt during resource limitations. The priority level defines the relative
importance of a resource request.
Values 1
to 15 are defined, with value 1 as the highest level of priority.
-
Values: 1 to 8 – Assigned for services that are authorized to
receive prioritized treatment within an operator domain.
-
Values: 9 to 15 – Assigned to resources that are authorized by
the Home network and thus applicable when a UE is roaming.
|
Provision
Default Bearer QoS
|
Must be
bound to the appropriate column in the STG. The data contained in the STG
column is of type True/False.
If the
value is True, the Default Bearer QoS information from the session is applied
to the rule, while QoS information derived from the prior parameters in this
STG is ignored.
|
Qci
|
The Quality of Service (QoS) Class Identifier.
The QoS
class identifier identifies a set of IP-CAN specific QoS parameters that define
QoS, excluding the applicable bitrates and ARP. It is applicable both for
uplink and downlink direction. The QCI values 0, 10 to 255 are divided for
usage as follows:
|
Rating
Group
|
The
charging key for the PCC rule used for rating purposes.
|
Realm
|
The
destination realm where the message is sent from PCRF.
|
Redirect
Address
|
Indicates
the target for redirected application traffic.
|
Redirect
Address Type
|
Defines
the address type of the address given in the Redirect-Server-Address AVP.
Default:
IPV4_ADDRESS
|
Redirect
Server Address
|
Indicates
the target for redirected application traffic.
|
Redirect
Support
|
This value
indicates that Redirection is enabled for a detected application's traffic.
|
Retry
Profile
|
Indicates
the Rule Retry Profile to be used. When CPS receives a Charging-Rule-Report
indicating failure to install or to activate one or more rules, it evaluates
the failed rules and takes further action.
|
Rule Group
|
Used to
classify rules at PCRF to change set of predefined rules based on policy.
This
parameter is optional.
|
Rule Name
|
A partial
name configured in Policy Builder (as derived using AF-Application-Identifier
and Media-Type values from the Custom dynamic rule name table in Gx Client).
Default:
AF
|
Scheduled
Hour
|
Can be
set to one of the following values:
Default: Turns
off the Hour Boundary RAR enhancement feature for look-ahead rules installation
at hour boundary. This causes rules to be installed at hour boundary as
applicable.
CurrentHour:
Rule activation time will be current time, deactivation time will be the next
hour.
NextHour: Rule
activation time will be the next hour, and deactivation time will be next-next
hour.
|
Search
Column
|
Must be
bound to the Key column in the STG. The data contained in the STG column is of
type Text.
|
Search
Group
|
A constant
value that CPS uses to search within the Search Table Group indicated by the
Search Table parameter.
|
Search
Table
|
The name
of the table from which to perform a lookup.
|
String
Value to Override
|
Indicates
whether overriding is required.
For
virtual services, if the value of “String Value” field matches exactly with the
value of “String Value To Override”, then the value of “String Value” is over
written with the “New String Value".
|
Tdf
Application Identifier
|
References
the application detection filter (for example, its value may represent an
application such as a list of URLs) to which the PCC rule for application
detection and control in the PCEF applies.
|
ToD Schedule
|
Identifies
the schedule for rule activation and deactivation.
|