t_config_wireless-adv-config

Available Languages

Updated:November 29, 2020

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Wireless Advanced Settings

Wireless Advanced Settings

On the Configuration > Wireless > Advanced page, you can perform the following advanced tasks:

ClosedLoad Balancing
  1. In the Load Balancing tab, in the Aggressive Load Balancing Window (Clients) field, enter a value between 1 and 20 to specify the load-balancing window and the number of client associations on the AP with the lightest load. For example, consider AP1 has the least number of clients (6), and the window size is set to 5, then each AP connected to the device can have 11 clients. As a result, every 12th client is load balanced, and a denial response is sent based on the configured value for the maximum denial count.

  2. In the Aggressive Load Balancing Denial Count field, enter a value between 0 and 10 to specify the number of times the client associations will be rejected for a particular AP.

    Note: In the Load Balancing Statistics area, you can view the load balancing statistical data.

  3. Click Apply.
ClosedBand Select
  1. In the Band Select tab, enter a value between 1 and 10 in the Cycle Count field. The cycle count sets the number of suppression cycles for a new client. The default cycle count is 2.
  2. In the Cycle Threshold field, enter a value between 1 and 1000 milliseconds for the scan cycle period threshold. This setting determines the time threshold during which new probe requests from a client come from a new scanning cycle. The default cycle threshold is 200 milliseconds.
  3. In the Age Out Suppression field, enter a value between 10 and 200 seconds. Age-out suppression sets the expiration time for pruning previously known 802.11b/g/n clients. The default value is 20 seconds. After this time elapses, clients become new and are subject to probe response suppression.
  4. In the Age Out Dual Band field, enter a value between 10 and 300 seconds. The age-out period sets the expiration time for pruning previously known dual-band clients. The default value is 50 seconds. After this time elapses, clients become new and are subject to probe response suppression.
  5. In the Client RSSI field, enter a value between -90 dBm and -20 dBm. This is the minimum RSSI for a client to respond to a probe.
  6. In the Client Mid RSSI field, enter a value between –20 dBm and –90 dBm. This parameter sets the mid-RSSI, whose value can be used for toggling 2.4 GHz probe suppression based on the RSSI value.
  7. Click Apply.
ClosedOptimized Roaming
  1. In the Optimized Roaming tab, navigate to the required radio tab: 5 GHz Band or 2.4 GHz Band.
  2. Check the Optimized Roaming Mode check box to enable it.
  3. Choose the required Optimized Roaming Date Rate Threshold. The threshold value options are different for 802.11a and 802.11b networks.
  4. Click Apply.
ClosedHigh Density

  1. In the High Density tab, choose the appropriate Rx SOP threshold for 5 GHz and 2.4 GHz networks.

    The table below shows the Rx SOP threshold values for high, medium and low levels for each 802.11 band:

    802.11 Band High Threshold Medium Threshold Low Threshold Auto
    5 GHz (802.11a) -76 dBm -78 dBm -80 dBm Use radio default
    2.4 GHz (802.11b) -79 dBm -82 dBm -85 dBm Use radio default
  2. In the Multicast Data Rate section, choose an appropriate multicast data rate for 5 GHz and 2.4 GHz networks.
  3. Click Apply.
ClosedPreferred Calls
  1. In the Preferred Calls tab, click Add.
  2. Enter the call index and number.
  3. Click Apply to Device.
ClosedRFID
  1. Check the RFID State check box to enable it.

  2. In the RFID Timeout field, enter a value between 60 and 7200 seconds. The RFID timeout field sets the expiration time. The default value is 1200 seconds.

  3. Click Apply.

 

Related Topics Link IconRelated Topics

 

© 2020 Cisco Systems, Inc. All rights reserved.

 

Was this Document Helpful?

FeedbackFeedback

Contact Cisco

This Document Applies to These Products