The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
A link test is used to determine the quality of the radio link between two devices. Two types of link-test packets are transmitted during a link test: request and response. Any radio receiving a link-test request packet fills in the appropriate text boxes and echoes the packet back to the sender with the response type set.
The radio link quality in the client-to-access point direction can differ from that in the access point-to-client direction due to the asymmetrical distribution of the transmit power and receive sensitivity on both sides. Two types of link tests can be performed: a ping test and a CCX link test.
With the ping link test, the controller can test link quality only in the client-to-access point direction. The RF parameters of the ping reply packets received by the access point are polled by the controller to determine the client-to-access point link quality.
With the CCX link test, the controller can also test the link quality in the access point-to-client direction. The controller issues link-test requests to the client, and the client records the RF parameters (received signal strength indicator [RSSI], signal-to-noise ratio [SNR], and so on). of the received request packet in the response packet. Both the link-test requestor and responder roles are implemented on the access point and controller. Not only can the access point or controller initiate a link test to a CCX v4 or v5 client, but a CCX v4 or v5 client can initiate a link test to the access point or controller.
The controller shows these link-quality metrics for CCX link tests in both directions (out— access point to client; in— client to access point):
Signal strength in the form of RSSI (minimum, maximum, and average)
Signal quality in the form of SNR (minimum, maximum, and average)
The controller shows this metric regardless of direction:
The controller software supports CCX versions 1 through 5. CCX support is enabled automatically for every WLAN on the controller and cannot be disabled. The controller stores the CCX version of the client in its client database and uses it to limit the features for this client. If a client does not support CCXv4 or v5, the controller performs a ping link test on the client. If a client supports CCXv4 or v5, the controller performs a CCX link test on the client. If a client times out during a CCX link test, the controller switches to the ping link test automatically.
Note | Follow the instructions in this section to perform a link test using either the GUI or the CLI. |
Use these commands to run a link test using the controller CLI:
Run a link test by entering this command:
When CCX v4 or later releases is enabled on both the controller and the client being tested, information similar to the following appears:
CCX Link Test to 00:0d:88:c5:8a:d1. Link Test Packets Sent...................................... 20 Link Test Packets Received................................. 10 Link Test Packets Lost (Total/AP to Client/Client to AP).... 10/5/5 Link Test Packets round trip time (min/max/average)......... 5ms/20ms/15ms RSSI at AP (min/max/average)................................ -60dBm/-50dBm/-55dBm RSSI at Client (min/max/average)............................ -50dBm/-40dBm/-45dBm SNR at AP (min/max/average)................................. 40dB/30dB/35dB SNR at Client (min/max/average)............................. 40dB/30dB/35dB Transmit Retries at AP (Total/Maximum)...................... 5/3 Transmit Retries at Client (Total/Maximum).................. 4/2 Transmit rate: 1M 2M 5.5M 6M 9M 11M 12M 18M 24M 36M 48M 54M 108M Packet Count: 0 0 0 0 0 0 0 0 0 2 0 18 0 Transmit rate: 1M 2M 5.5M 6M 9M 11M 12M 18M 24M 36M 48M 54M 108M Packet Count: 0 0 0 0 0 0 0 0 0 2 0 8 0
When CCX v4 or later releases is not enabled on either the controller or the client being tested, fewer details appear:
Ping Link Test to 00:0d:88:c5:8a:d1. Link Test Packets Sent.......................... 20 Link Test Packets Received...................... 20 Local Signal Strength........................... -49dBm Local Signal to Noise Ratio..................... 39dB
Adjust the link-test parameters that are applicable to both the CCX link test and the ping test by entering these commands from configuration mode:
linktest frame-size size_of_link-test_frames
linktest num-of-frame number_of_link-test_request_frames_per_test